Toshiba e-Studio 195i
Рейтинг
Модули
OPTICAL-FRAME-ASY
FUSER-1-ASY
PLATEN-ASY
FUSER-2-ASY
FRONT-FRAME-ASY
CONTROL-PANEL-ASY
MAIN-DRIVE-ASY
DRAWER-ASY
REAR-FRAME-ASY
COVER-1-ASY
STAY-ASY
BYPASS-ASY
COVER-GUIDE-ASY
REPLACE UNIT
TRANSPORT-CHARGER-ASY
BASE-FRAME-ASY
ALIGNING-ASY
BYPASS-FEEDER-ASY
DEVELOPER-ASY
OPTICAL-DRIVE-ASY
COVER-2-ASY
COVER-3-ASY
MAIN-CHARGER-ASY
RECYCLE-ASY
GUIDE-ALIGNING-ASY
CLEANER-ASY
Детали FUSER-2-ASY
| Деталь: | LVR-OPEN-SNS-280 |
| Парткод: | 6LE60780000 |
| Деталь: | SPR-OPEN-SNS |
| Парткод: | 44202846000 |
| Деталь: | SHAFT-OPN-SNS |
| Парткод: | 6LA67393000 |
| Деталь: | BRKT-SW-PLATEN |
| Парткод: | 6LH24131000 |
| Деталь: | MYLAR-HRNS-INV-LEX |
| Парткод: | 6LH25800000 |
| Деталь: | HRNS-SCN-CISM-H220 |
| Парткод: | 6LJ49700000 |
| Деталь: | ASY-CIS-CJ4 |
| Парткод: | 6LJ49014000 |
| Деталь: | ASYS-COV-HNS-HTR |
| Парткод: | 6LE60858000 |
| Деталь: | ASY-CASE-CIS |
| Парткод: | 6LE60691000 |
| Деталь: | FOOT-CRG-3.64 |
| Парткод: | 4408604590 |
| Деталь: | SPRING-CIS |
| Парткод: | 6LE60703000 |
| Деталь: | STOP-BELT |
| Парткод: | 6LE60695000 |
| Деталь: | LG248NL1 |
| Парткод: | C0-11250000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | S/TPD3/FHEXM-3X8-ZU3 |
| Парткод: | X0-02593000 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | MYLAR-HRNS-CIS |
| Парткод: | 6LJ49041000 |
| Деталь: | SNSR-PS-181EL1-S42R |
| Парткод: | 6LE64034000 |
| Деталь: | S/TPP/BID-3X8-NI |
| Парткод: | 6LA80090000 |
| Деталь: | ASY-D-HTR-L-U |
| Парткод: | 6LE60856100 |
| Деталь: | ASY-D-HTR-L-E |
| Парткод: | 6LE60856200 |
| Деталь: | ASY-D-HTR-R-U |
| Парткод: | 6LE60854100 |
| Деталь: | ASY-D-HTR-R-E |
| Парткод: | 6LE60854200 |
| Деталь: | SNSR-PS181EL1-S42 |
| Парткод: | 6LE63995000 |
| Деталь: | THRMST-CS-7SA-280 |
| Парткод: | 6LE63996000 |
| Деталь: | THRMST-CS-7L-280 |
| Парткод: | 6LE64009000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | FRAME-FUS-HR-284-N |
| Парткод: | 6LH90400000 |
| Деталь: | ROLL-FUS-GUIDE |
| Парткод: | 6LE25931000 |
| Деталь: | PLT-NUT-LMP-284 |
| Парткод: | 6LH24660000 |
| Деталь: | PLT-THMS-LMP-280 |
| Парткод: | 6LE58575000 |
| Деталь: | THRMST-HTR-284 |
| Парткод: | 6LH27402000 |
| Деталь: | THMS-HTR-280 |
| Парткод: | 6LE63998000 |
| Деталь: | ASYS-HLD-THMIS-280 |
| Парткод: | 6LE58520000 |
| Деталь: | HR-1640-U |
| Парткод: | 6LE19935000 |
| Деталь: | HRNS-LP-ACIN2-280 |
| Парткод: | 6LE63314000 |
| Деталь: | GEAR-HR-RLR |
| Парткод: | 6LH24603000 |
| Деталь: | CRR-HT/RLR |
| Парткод: | 6LH24640000 |
| Деталь: | SCRAPER-282 |
| Парткод: | 6LE58405000 |
| Деталь: | SPE-SCR-HR-371 |
| Парткод: | 6LA84096000 |
| Деталь: | EARTH-FUS-EXIT |
| Парткод: | 6LE58530000 |
| Деталь: | SFT-EXIT-IDLE-280 |
| Парткод: | 6LE58600000 |
| Деталь: | ROLL-EXIT-L-282 |
| Парткод: | 6LE58555000 |
| Деталь: | ROLLER-EXIT-282 |
| Парткод: | 6LE58587000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | HLDR-GEAR-EXIT-280 |
| Парткод: | 6LE58401000 |
| Деталь: | GEAR-10S35-5 |
| Парткод: | 6LE58540000 |
| Деталь: | GEAR-10S20-8 |
| Парткод: | 6LE58570000 |
| Деталь: | SPG-T-EXIT-R-280 |
| Парткод: | 6LE58611000 |
| Деталь: | SPG-T-EXIT-F-280 |
| Парткод: | 6LE58615000 |
| Деталь: | EARTH-FUS-HEAT |
| Парткод: | 6LE58535000 |
| Деталь: | ASYS-GEAR-HR-EXIT |
| Парткод: | 6LE58490000 |
| Деталь: | GEAR-10H21_10S20-6-FUS |
| Парткод: | 6LH24602000 |
| Деталь: | ROL-IDLE-FUS-284 |
| Парткод: | 6LH24605000 |
| Деталь: | BUSH-HR_RLR |
| Парткод: | 6LH24604000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | SCREW-PINION |
| Парткод: | 6LA04456000 |
| Деталь: | ROLL-GUIDE-EXIT-280 |
| Парткод: | 6LE58505000 |
| Деталь: | SPG-T-GUIDE-OPEN-2 |
| Парткод: | 6LE58886000 |
| Деталь: | SPG-E-FUS-GEAR |
| Парткод: | 6LE58770000 |
| Деталь: | PLT-NUT-FUS-280 |
| Парткод: | 6LE58564000 |
| Деталь: | SCREW-M3-FUS-C |
| Парткод: | 6LA36276000 |
| Деталь: | GUIDE- FUS-CURL-282 |
| Парткод: | 6LE58625000 |
| Деталь: | SCREW-HLDR-MG |
| Парткод: | 6LA65683000 |
| Деталь: | S/BID-M3X8-NI |
| Парткод: | X0-00434000 |
| Деталь: | USUITA-SPSEMS-4X8-6 |
| Парткод: | 6LH55300000 |
| Деталь: | S/PAN/SWWP-M3X8-NI |
| Парткод: | X0-00077000 |
| Деталь: | S/TPD3/FHEXM-3X6-ZU3 |
| Парткод: | X0-02592000 |
| Деталь: | S/TPP/BID-3*8-NI |
| Парткод: | 6LA80090000 |
| Деталь: | S/FHEXM-M3X10-NI |
| Парткод: | X0-02232000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | USUITA-SEMS-3X5-6 |
| Парткод: | 6LH55301000 |
| Деталь: | LVR-EXIT-PAPER |
| Парткод: | 6LJ22901000 |
| Деталь: | LAMP-HTR-C-371-NAD |
| Парткод: | 6LE58630100 |
| Деталь: | LAMP-HTR-C-371-MJD |
| Парткод: | 6LE58630200 |
| Деталь: | LAMP-HTR-S-371-NAD |
| Парткод: | 6LE58631100 |
| Деталь: | LAMP-HTR-S-371-MJD |
| Парткод: | 6LE58631200 |
| Деталь: | ASYS-GLASS-ADF-280 |
| Парткод: | 6LE60728000 |
| Деталь: | HOLDER-GLASS-280 DV |
| Парткод: | 6LE60770100 |
| Деталь: | MYLAR-GLASS-F |
| Парткод: | 6LE60733000 |
| Деталь: | ASY-GLASS-PLATEN-280-LCJ4 |
| Парткод: | 6LE60740900 |
| Деталь: | ASY-GLASS-PLATEN-280-ACJ4 |
| Парткод: | 6LE60740800 |
| Деталь: | ASY-GLASS-PLATEN-280-KCJ4 |
| Парткод: | 6LE60740A00 |
| Деталь: | S/BID-M3X6-NI |
| Парткод: | X0-00430000 |
| Деталь: | LID-SCREW-H150 |
| Парткод: | 6LE08071200 |
| Деталь: | FRAME-FUS-PR-280 |
| Парткод: | 6LH29500000 |
| Деталь: | LVR-P-REL-280 |
| Парткод: | 6LE58710000 |
| Деталь: | BUSH-PR-280 |
| Парткод: | 6LE58690000 |
| Деталь: | HR-1640-L |
| Парткод: | 6LE19936000 |
| Деталь: | LVR-PRESS-280 |
| Парткод: | 6LE58720000 |
| Деталь: | SPE-PR-280 |
| Парткод: | 6LE58750000 |
| Деталь: | EARTH-FUS-PRS-280 |
| Парткод: | 6LE58700000 |
| Деталь: | LG248NL1 |
| Парткод: | C0-11250000 |
| Деталь: | GUIDE-ENT-FUS-280 |
| Парткод: | 6LE58880000 |
| Деталь: | COV-FUS-RER-280 |
| Парткод: | 6LE58870000 |
| Деталь: | HRNS-EXIT-280 |
| Парткод: | 6LE63299000 |
| Деталь: | GUIDE-OPEN-FUS-282_N |
| Парткод: | 6LH24613000 |
| Деталь: | SPG-T-ACT-EXIT-282 |
| Парткод: | 6LE58862000 |
| Деталь: | ACTR-EXIT-282_N |
| Парткод: | 6LH24612000 |
| Деталь: | LBL-W-HOT-280 |
| Парткод: | 6LE58890000 |
| Деталь: | MYLAR-COV-SENS |
| Парткод: | 6LE58765000 |
| Деталь: | LBL-FUS-OPE |
| Парткод: | 6LE58896000 |
| Деталь: | STOPPER-FUS-GID |
| Парткод: | 6LE58407000 |
| Деталь: | SCREW-SPEAKER-ZU3 |
| Парткод: | 6LA47979000 |
| Деталь: | S/TPD3/FHEXM-3X6-ZU3 |
| Парткод: | X0-02592000 |
| Деталь: | BUSH-RGST-F |
| Парткод: | 6LE57207000 |
| Деталь: | SPG-LEVER-TNR-C |
| Парткод: | 6LA88014000 |
| Деталь: | LEVER-TNR-C |
| Парткод: | 6LA88010000 |
| Деталь: | STUD-DRSW-TR |
| Парткод: | 44200855000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | UAMS-05SN-W |
| Парткод: | F0-00043000 |
| Деталь: | SW-ITLOCKV |
| Парткод: | 6LH27405000 |
| Деталь: | BRKT-SW-INT |
| Парткод: | 6LE57911000 |
| Деталь: | S/TPP/BID-3*8-NI |
| Парткод: | 6LA80090000 |
| Деталь: | S/TPS/FPAN-3X14-NC |
| Парткод: | X0-01615000 |
| Деталь: | S/TPD3/FHEXM-3X8-ZU3 |
| Парткод: | X0-02593000 |
| Деталь: | ASYS-KEY-START-LH |
| Парткод: | 6LH88234000 |
| Деталь: | KEY-CL-STOP-LH-H |
| Парткод: | 6LH22450000 |
| Деталь: | KEY-FC-LH-E |
| Парткод: | 6LE54639000 |
| Деталь: | HOLDER-LED-LH |
| Парткод: | 6LE54640000 |
| Деталь: | KEY-COPY-H |
| Парткод: | 6LH22445000 |
| Деталь: | KEY-COPY-H-SUB |
| Парткод: | 6LE54668000 |
| Деталь: | KEY-TEN-LH-H |
| Парткод: | 6LH22451000 |
| Деталь: | KEY-DEN-LH |
| Парткод: | 6LE54712000 |
| Деталь: | HOLDER-LED-TEL-H |
| Парткод: | 6LE54651000 |
| Деталь: | KEY-LH |
| Парткод: | 6LE54644000 |
| Деталь: | KEY-COPY-LH |
| Парткод: | 6LE54646000 |
| Деталь: | KEY-ENTER-H |
| Парткод: | 6LE54715000 |
| Деталь: | KEY-ES-H |
| Парткод: | 6LH22444000 |
| Деталь: | KEY-COPY-SETTINGS-H |
| Парткод: | 6LE54652000 |
| Деталь: | HOLDER-LED-PAPER-H |
| Парткод: | 6LE54666000 |
| Деталь: | COVER-DIAL-H |
| Парткод: | 6LE54667000 |
| Деталь: | DSP-LCD7086-284 |
| Парткод: | 6LH29350000 |
| Деталь: | PWA-F-HPNL-286 |
| Парткод: | 6LH27008000 |
| Деталь: | ASYS-BRKT-CONPANE-H |
| Парткод: | 6LE54681000 |
| Деталь: | BRKT-CONPANE-H-R |
| Парткод: | 6LE54661000 |
| Деталь: | COVER-CONPANE-H-L DV |
| Парткод: | 6LE54672100 |
| Деталь: | HRNS-LCD-282 |
| Парткод: | 6LE63325000 |
| Деталь: | ASYB-CONPANE-H-U N DV |
| Парткод: | 6LH22436700 |
| Деталь: | ASYB-CONPANE-H-E DV |
| Парткод: | 6LE54658600 |
| Деталь: | ASYB-CONPANE-H-C N DV |
| Парткод: | 6LH22436800 |
| Деталь: | ASYB-CONPANE-H-T N DV |
| Парткод: | 6LH22436900 |
| Деталь: | S/TPB/BID-2X6-ZU3 |
| Парткод: | X0-02117000 |
| Деталь: | S/TPP/BID-3*8-NI |
| Парткод: | 6LA80090000 |
| Деталь: | S/TPD3/FHEXM-3X8-ZU3 |
| Парткод: | X0-02593000 |
| Деталь: | KEY-SELECT-H |
| Парткод: | 6LE54714000 |
| Деталь: | KEY-SELECT-HU |
| Парткод: | 6LE54714100 |
| Деталь: | SHIELD-CONPANE-H |
| Парткод: | 6LE54700000 |
| Деталь: | SHIELD-CONP-H-MAIN-TWD |
| Парткод: | 6LH88201000 |
| Деталь: | SHIELD-CONPANE-H-TW |
| Парткод: | 6LE54716000 |
| Деталь: | MOTR.D-MAIN-H150 |
| Парткод: | 6LH93200000 |
| Деталь: | GEAR-5H62L_10H25L-6 |
| Парткод: | 6LE56640000 |
| Деталь: | GEAR-10H37L_10H17L-6 |
| Парткод: | 6LE56642000 |
| Деталь: | GEAR-10H36R_10H21R-6 |
| Парткод: | 6LE56645000 |
| Деталь: | STOPPER-6-3 |
| Парткод: | 4406520870 |
| Деталь: | GEAR-10S23_P2STE62_10H21R |
| Парткод: | 6LE56641000 |
| Деталь: | GEAR-10S21_P2STE43-6 |
| Парткод: | 6LE56644000 |
| Деталь: | ASYS-GEAR-5H56L-6-COUPL-N |
| Парткод: | 6LH23425000 |
| Деталь: | COUPL-GR-P-JOINT-280 |
| Парткод: | 6LE56653000 |
| Деталь: | ASYS-GEAR-10S24_P2STE30-N |
| Парткод: | 6LH23426000 |
| Деталь: | BLT.SY-ST2-400-4-B |
| Парткод: | 6LH23465000 |
| Деталь: | SPG-TENS-ROL-280 |
| Парткод: | 6LE56610000 |
| Деталь: | ASYS-MOTRD-TNR-470 |
| Парткод: | 6LH53764000 |
| Деталь: | ASYS-BRKT-GEAR-284 |
| Парткод: | 6LH23431000 |
| Деталь: | GEAR-10H21R-6 |
| Парткод: | 6LE56630000 |
| Деталь: | GEAR-10H23L-6 |
| Парткод: | 6LE56623000 |
| Деталь: | GEAR-8S21-6 |
| Парткод: | 6LE56618000 |
| Деталь: | TENS-ROLLER |
| Парткод: | 6LA82311000 |
| Деталь: | GEAR-10H21L-6 |
| Парткод: | 6LE56620000 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | GEAR-10S37_10H17R_10S19-8 |
| Парткод: | 6LE56646000 |
| Деталь: | GEAR-5H60L-6-WORM-TNR |
| Парткод: | 6LE56633000 |
| Деталь: | BUSH-8X12X8F-NU4 |
| Парткод: | 6LH23442000 |
| Деталь: | STOP RING |
| Парткод: | 41306265000 |
| Деталь: | S/TPP/BID-3*8-NI |
| Парткод: | 6LA80090000 |
| Деталь: | GEAR-10H21L_8S19-6 |
| Парткод: | 6LE56613000 |
| Деталь: | HLDR-SFT-RGST-DRV |
| Парткод: | 6LE56634000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/TPD3/FHEXM-3X8-ZU3 |
| Парткод: | X0-02593000 |
| Деталь: | S/PAN-M2.6X4-NC |
| Парткод: | X0-01670000 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | ASYS-BRKT-DRV-CLTCH-G |
| Парткод: | 6LJ48214000 |
| Деталь: | SFT-CPL-CHA-G2 |
| Парткод: | 6LJ48212000 |
| Деталь: | BUSH-06-16-G |
| Парткод: | 6LJ48211000 |
| Деталь: | GEAR-10H22L_8S22-6-G |
| Парткод: | 6LJ48210000 |
| Деталь: | ASYS-BRKT-DRV-FEED-G |
| Парткод: | 6LJ48217000 |
| Деталь: | SPG-CPL-CHA-G |
| Парткод: | 6LJ48213000 |
| Деталь: | CPL-CSSTT-CHA-G |
| Парткод: | 6LJ48208000 |
| Деталь: | GEAR-8S27-6-G |
| Парткод: | 6LJ48209000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | RR/E-5-POM |
| Парткод: | 6LE53442000 |
| Деталь: | LWS-1S |
| Парткод: | F0-00235000 |
| Деталь: | LWS-05 |
| Парткод: | F0-00035000 |
| Деталь: | MYLAR-GUARD-HRNS |
| Парткод: | 6LJ50682000 |
| Деталь: | CATCH-CST-280 |
| Парткод: | 6LH22003000 |
| Деталь: | STOP-PLATE-CSSTT |
| Парткод: | 6LE53718000 |
| Деталь: | SPG-LATCH-TRAY |
| Парткод: | 6LE53730000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | GEAR-10S18-8-TRAY |
| Парткод: | 6LE53717000 |
| Деталь: | ASYS-ROL-CST-36-L35 |
| Парткод: | 6LJ46929000 |
| Деталь: | S/TPP/BID-3X8-NI |
| Парткод: | X0-01989000 |
| Деталь: | BRKT-TRAY-280 |
| Парткод: | 6LE53746000 |
| Деталь: | SPG-CSSTT-280 |
| Парткод: | 6LE53732000 |
| Деталь: | WALL-CST-END-LE_4 |
| Парткод: | 6LJ46915000 |
| Деталь: | TRAY-CST-LE_4 |
| Парткод: | 6LJ46900000 |
| Деталь: | STOP-RING-8 |
| Парткод: | 41306265000 |
| Деталь: | SPG-T-END-WALL |
| Парткод: | 6LJ46922000 |
| Деталь: | SPG-PAD-CHA-G |
| Парткод: | 6LJ46907000 |
| Деталь: | SPC-LVR-WALL-F |
| Парткод: | 6LA56695000 |
| Деталь: | SLIDE-WALL-R-G |
| Парткод: | 6LJ46901000 |
| Деталь: | SLIDE-WALL-F-G |
| Парткод: | 6LJ46902000 |
| Деталь: | SHAFT_STOPER_WALL |
| Парткод: | 6LJ46919000 |
| Деталь: | PLT-WALL-GEAR-G |
| Парткод: | 6LJ46917000 |
| Деталь: | P/PRL/AH7-2X16-SS |
| Парткод: | X0-01533000 |
| Деталь: | LEVER-LOCK-WALL-G |
| Парткод: | 6LJ46916000 |
| Деталь: | LBL-MAX-CST-F43X |
| Парткод: | 6LH05749000 |
| Деталь: | COVER-CSSTT-G-TN |
| Парткод: | 6LJ46908100 |
| Деталь: | ASYS-ROL-PIC-CST |
| Парткод: | 6LJ46934000 |
| Деталь: | BUSH-8X12X8F-NU4 |
| Парткод: | 6LH23442000 |
| Деталь: | ASYS-ROL-CST-G |
| Парткод: | 6LJ46904000 |
| Деталь: | ASYS-HOLD-PAD-G |
| Парткод: | 6LJ46914000 |
| Деталь: | ASYS-PLATE-CSSTT-G |
| Парткод: | 6LJ46913000 |
| Деталь: | LBL-OPE-CST |
| Парткод: | 6LJ46928000 |
| Деталь: | LBL-CST-PUSH-280A |
| Парткод: | 6LE53757000 |
| Деталь: | LBL-CST-PUSH-280E |
| Парткод: | 6LE53758000 |
| Деталь: | SIZE-CST-390-UC |
| Парткод: | 6LE03708000 |
| Деталь: | SIZE-CST-390-E |
| Парткод: | 6LE03709000 |
| Деталь: | SIZE-CST-390-C |
| Парткод: | 6LE03715000 |
| Деталь: | GEAR-10S19-6 |
| Парткод: | 6LE56647000 |
| Деталь: | GEAR-10S17_10S19-6 |
| Парткод: | 6LE56631000 |
| Деталь: | GEAR-10S17-5-CPG |
| Парткод: | 6LE56622000 |
| Деталь: | SPG-DRV-CL-280 |
| Парткод: | 6LE56612000 |
| Деталь: | CPG-DRV-CLN-280 |
| Парткод: | 6LE56609000 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | GEAR-10S26_10S37-6 |
| Парткод: | 6LE56643000 |
| Деталь: | ASYS-SHAFT-DRUM-280 |
| Парткод: | 6LE56662000 |
| Деталь: | GEAR-10H36R-8 |
| Парткод: | 6LE56648000 |
| Деталь: | CPG-DRUM-AW5 |
| Парткод: | 41314022000 |
| Деталь: | SPG-C-173 |
| Парткод: | 6LA79504000 |
| Деталь: | SPL-GUIDE-TR |
| Парткод: | 6LE62434000 |
| Деталь: | PLATE-TRU |
| Парткод: | 6LE62430000 |
| Деталь: | SPL-BIAS-RGST |
| Парткод: | 6LE56606000 |
| Деталь: | HRNS-HVPS1-280 |
| Парткод: | 6LE63315000 |
| Деталь: | HRNS-HVT-GB-280 |
| Парткод: | 6LE63318000 |
| Деталь: | SPL-CH-M |
| Парткод: | 6LA85009000 |
| Деталь: | SPL-GRID |
| Парткод: | 6LE86050000 |
| Деталь: | HRNS-HVPS2-280 |
| Парткод: | 6LE63316000 |
| Деталь: | PLT-TERM-DEV |
| Парткод: | 6LA82004000 |
| Деталь: | SPC-TERM |
| Парткод: | 6LA82006000 |
| Деталь: | HRNS-HVPS3-280 |
| Парткод: | 6LE63317000 |
| Деталь: | HRNS-ACIN1-280 |
| Парткод: | 6LE63313000 |
| Деталь: | ASYS-PLATE-DRIVE-DEV |
| Парткод: | 6LE56635000 |
| Деталь: | ASY-HOLD-SP-TNR |
| Парткод: | 6LE58079000 |
| Деталь: | PWA-F-SRAM-286 |
| Парткод: | 6LH27013200 |
| Деталь: | LI-BAT-CR-2450 |
| Парткод: | 6LE90510000 |
| Деталь: | ASY-PWA-MAIN-222S |
| Парткод: | 6LJ49814000 |
| Деталь: | ASY-PWA-MAIN-223S |
| Парткод: | 6LJ49814100 |
| Деталь: | ASY-PWA-MAIN-224S |
| Парткод: | 6LJ49814200 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | P/PRL/AH7-2X10-SS |
| Парткод: | X0-00980000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/TPP/BID-3*8-NI |
| Парткод: | 6LA80090000 |
| Деталь: | BU14P-TZ-S (LF)(SN) |
| Парткод: | E0-09932000 |
| Деталь: | UAMS-05S-2 |
| Парткод: | F0-00042000 |
| Деталь: | S/PAN-M3X6-NI |
| Парткод: | X0-00057000 |
| Деталь: | WS-4W |
| Парткод: | F0-01252000 |
| Деталь: | CBT-10S0 |
| Парткод: | F0-01553000 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | SHAFT-DRV-TNR-280 |
| Парткод: | 6LE56660000 |
| Деталь: | SPG-DRV-TN-280 |
| Парткод: | 6LE56611000 |
| Деталь: | CPG-TC-280 |
| Парткод: | 6LE56666000 |
| Деталь: | CPG-TC-470-C |
| Парткод: | 6LH57004400 |
| Деталь: | CPG-TC-470-D |
| Парткод: | 6LH57004100 |
| Деталь: | CPG-TC-470-E |
| Парткод: | 6LH57004300 |
| Деталь: | CPG-TC-470-U |
| Парткод: | 6LH57004200 |
| Деталь: | CPG-TC-470-J |
| Парткод: | 6LH57004000 |
| Деталь: | PWA-F-FUS-371 |
| Парткод: | 6LA88759000 |
| Деталь: | COVER-PWA-FUS-280 |
| Парткод: | 6LE55664000 |
| Деталь: | S/TPD3/FHEXM-3X8-ZU3 |
| Парткод: | X0-02593000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | S/TPS/FHEXM/R-3X8-ZU3 |
| Парткод: | X0-02420000 |
| Деталь: | S/BID-M3X6-NI |
| Парткод: | X0-00430000 |
| Деталь: | HRNS-CTIF-H220 |
| Парткод: | 6LJ49701000 |
| Деталь: | BRKT-COV-TNR-SHT |
| Парткод: | 6LJ49110000 |
| Деталь: | COVER-FRONT-R |
| Парткод: | 6LE55209000 |
| Деталь: | COVER-FRONT-L |
| Парткод: | 6LE55219000 |
| Деталь: | BRKT-FRAME-SENSOR |
| Парткод: | 6LE57906000 |
| Деталь: | SW-ITLOCKV |
| Парткод: | 6LH27405000 |
| Деталь: | MYLAR-FRM-SENSOR |
| Парткод: | 6LE55221000 |
| Деталь: | COVER-TR_DV |
| Парткод: | 6LJ47407100 |
| Деталь: | COVER-STOP-P DV |
| Парткод: | 6LE55260100 |
| Деталь: | COVER-DUCT-TRAY |
| Парткод: | 6LH88547000 |
| Деталь: | COVER-LEFT |
| Парткод: | 6LE55238000 |
| Деталь: | FILTER-COV-LEFT |
| Парткод: | 6LE55240000 |
| Деталь: | COVER-TRAY-BACK |
| Парткод: | 6LE55248000 |
| Деталь: | COVER-PILLAR-FRT-B |
| Парткод: | 6LE55268000 |
| Деталь: | COVER-PILLAR-FRT-TN_FW |
| Парткод: | 6LJ47405000 |
| Деталь: | COVER-RIGHT |
| Парткод: | 6LE55229000 |
| Деталь: | SHIELD-COV-TRAY |
| Парткод: | 6LH88544000 |
| Деталь: | CS1A-B2CA |
| Парткод: | E0-01853000 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | S/TPD3/FHEXM-3X8-ZU3 |
| Парткод: | X0-02593000 |
| Деталь: | S/TPS/FPAN-3X14-NC |
| Парткод: | X0-01615000 |
| Деталь: | COV-TRAY-EXIT-SUB |
| Парткод: | 6LJ47406000 |
| Деталь: | ASYS-COVER-EMBLEM-195 |
| Парткод: | 6LJ47400200 |
| Деталь: | ASYS-COVER-EMBLEM-195BM |
| Парткод: | 6LJ47400500 |
| Деталь: | ASYS-COVER-EMBLEM-225 |
| Парткод: | 6LJ47400300 |
| Деталь: | ASYS-COVER-EMBLEM-225BM |
| Парткод: | 6LJ47400600 |
| Деталь: | ASYS-COVER-EMBLEM-245 |
| Парткод: | 6LJ47400400 |
| Деталь: | ASYS-COVER-EMBLEM-245BM |
| Парткод: | 6LJ47400700 |
| Деталь: | LBL-SERVICE-45 |
| Парткод: | 44204604000 |
| Деталь: | LBL-SERVICE-45C |
| Парткод: | 6LA56227000 |
| Деталь: | LBL-SERVICE-45-TWD |
| Парткод: | 6LA48504000 |
| Деталь: | LBL-CAU-LASER |
| Парткод: | 6LE59160000 |
| Деталь: | LBL-CAU-LASER-CND |
| Парткод: | 6LH29160000 |
| Деталь: | LBL-CAU-LASER-TWD |
| Парткод: | 6LE65093000 |
| Деталь: | LBL-ENERGY-T-PS-N |
| Парткод: | 6LE84761000 |
| Деталь: | HRNS-D/H-280 |
| Парткод: | 6LE63406000 |
| Деталь: | THRMST-CS-7L |
| Парткод: | 6LE09486000 |
| Деталь: | HRNS-D/H-DRM-280 |
| Парткод: | 6LE63375000 |
| Деталь: | BRKT-EARTH-TRU |
| Парткод: | 6LE62432000 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | COVER-HRNS-OPE |
| Парткод: | 6LE58010000 |
| Деталь: | ASYS-BEAM-R |
| Парткод: | 6LE57864000 |
| Деталь: | LWS-1U |
| Парткод: | F0-00024000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | HEATER-D-DRM-280E |
| Парткод: | 6LE64030000 |
| Деталь: | HEATER-D-DRM-280U |
| Парткод: | 6LE64029000 |
| Деталь: | HRNS-HPNL-H222 |
| Парткод: | 6LJ49718000 |
| Деталь: | HRNS-HPNL-152TW |
| Парткод: | 6LH93511000 |
| Деталь: | S/TPD3/FHEXM-3X8-ZU3 |
| Парткод: | X0-02593000 |
| Деталь: | TRAY-BYP-TOP-284DV |
| Парткод: | 6LH21852100 |
| Деталь: | SHEET-PAD-GUIDE-F |
| Парткод: | 6LA29009000 |
| Деталь: | GUIDE-TRAY-BYP-R_DV |
| Парткод: | 6LE53419100 |
| Деталь: | GUIDE-TRAY-BYP-L DV |
| Парткод: | 6LE53418100 |
| Деталь: | SPG-GUIDE |
| Парткод: | 6LE53407000 |
| Деталь: | LVR-GID DV |
| Парткод: | 6LE53406100 |
| Деталь: | GUIDE-SUB-R DV |
| Парткод: | 6LE53411100 |
| Деталь: | GUIDE-SUB-L DV |
| Парткод: | 6LE53409100 |
| Деталь: | GEAR-10S18-6-BYP-TRAY |
| Парткод: | 6LE53504000 |
| Деталь: | HOLDER-PINI-280 |
| Парткод: | 6LE53505000 |
| Деталь: | TRAY-BYP-SUB-284DV |
| Парткод: | 6LH21850100 |
| Деталь: | TRAY-BYP-BOT-284DV |
| Парткод: | 6LH21851100 |
| Деталь: | S/TPP/BID-3X8-NI |
| Парткод: | 6LA80090000 |
| Деталь: | ARM-TRAY-SFB |
| Парткод: | 6LE53449000 |
| Деталь: | PUSHER-PAPER-GUIDE |
| Парткод: | 6LE53506000 |
| Деталь: | COVER-HRNS-BASE |
| Парткод: | 6LE58021000 |
| Деталь: | SPG-PUSHER-GUIDE |
| Парткод: | 6LE53457000 |
| Деталь: | COVER-PUSHER-G FW |
| Парткод: | 6LE53507100 |
| Деталь: | ASYS-PAD-PUSHER-GUIDE |
| Парткод: | 6LE53488000 |
| Деталь: | PAD-ADH-TAPE-S |
| Парткод: | 6LE53454000 |
| Деталь: | TRAY-SNSR-FED-284 |
| Парткод: | 6LH23928000 |
| Деталь: | ACTR-SNSR-SFB |
| Парткод: | 6LE53482000 |
| Деталь: | SPG-SNSR-SFB-90 |
| Парткод: | 6LE53485000 |
| Деталь: | HRNS-SFB-SNR-280 |
| Парткод: | 6LE63308000 |
| Деталь: | LG248NL1 |
| Парткод: | C0-11250000 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | ASYS-CASE-SIDE-H |
| Парткод: | 6LE62307100 |
| Деталь: | ASYS-COV-SIDE-IN |
| Парткод: | 6LE62338000 |
| Деталь: | FILTER-OZONE-TRU-371 |
| Парткод: | 6LA88240000 |
| Деталь: | ASYS-COV-FILTER |
| Парткод: | 6LE62374000 |
| Деталь: | GUIDE-PUSH-TRU |
| Парткод: | 6LE62392000 |
| Деталь: | SPC-PUSH-RGST |
| Парткод: | 6LE62403000 |
| Деталь: | PUSH-ROL-RGST |
| Парткод: | 6LE62400000 |
| Деталь: | ARM-TRU-F |
| Парткод: | 6LE62311000 |
| Деталь: | ARM-TRU-R |
| Парткод: | 6LE62387000 |
| Деталь: | GUIDE-TR-280 |
| Парткод: | 6LE62348000 |
| Деталь: | TERM-CH-TR-280 |
| Парткод: | 6LE62354000 |
| Деталь: | SPC-CH-TR-R |
| Парткод: | 6LE62351000 |
| Деталь: | EARTH-TRU |
| Парткод: | 6LE62345000 |
| Деталь: | LEVER-SIDE-COV |
| Парткод: | 6LE62410000 |
| Деталь: | SPC-CH-TR |
| Парткод: | 6LA88343000 |
| Деталь: | GEAR-10S020-08 |
| Парткод: | 6LA85880000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | ROLLER-RGST-280 |
| Парткод: | 6LH23932000 |
| Деталь: | STOP RING |
| Парткод: | 41306265000 |
| Деталь: | WSHR-85X185XR5-ABS |
| Парткод: | 6LE62470000 |
| Деталь: | FAN_D07F-24SG25EX |
| Парткод: | 6LH93201000 |
| Деталь: | S/TPP/BID-3*8-NI |
| Парткод: | 6LA80090000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | TR-CH-1640 |
| Парткод: | 6LE65620000 |
| Деталь: | CLN-DRUM-1640 |
| Парткод: | 6LE65630000 |
| Деталь: | DEV-UNIT-1640 |
| Парткод: | 6LE65600000 |
| Деталь: | FUSER-1650-115 |
| Парткод: | 6LE65510100 |
| Деталь: | FUSER-1650-230 |
| Парткод: | 6LE65510200 |
| Деталь: | BUSH-RLR-GUIDE |
| Парткод: | 41306677000 |
| Деталь: | CASE-CH-TR |
| Парткод: | 6LA88230000 |
| Деталь: | DAMPER |
| Парткод: | 41306712000 |
| Деталь: | EARTH-CH-TR |
| Парткод: | 6LA88304000 |
| Деталь: | GEAR-RLR-GUIDE |
| Парткод: | 41306272000 |
| Деталь: | GUIDE-CH-TR-280 |
| Парткод: | 6LE62303000 |
| Деталь: | HANGER-WIRE-TR |
| Парткод: | 4401764730 |
| Деталь: | LID-CH-TR-R |
| Парткод: | 6LA88245000 |
| Деталь: | PLT-CH-TR |
| Парткод: | 6LA88238000 |
| Деталь: | PLT-TERM-1 |
| Парткод: | 44203860000 |
| Деталь: | LID-CH-TR-F |
| Парткод: | 6LA88244000 |
| Деталь: | Roller-Guide |
| Парткод: | 6LH23931000 |
| Деталь: | S/TPP/BID-3*8-NI |
| Парткод: | 6LA80090000 |
| Деталь: | SPRING-TENS-CH |
| Парткод: | 6LA84935000 |
| Деталь: | SUPPORTER-371 |
| Парткод: | 6LA88248000 |
| Деталь: | WIRE-CH-060-353-R |
| Парткод: | 6LA88250000 |
| Деталь: | AC-P10CF34 |
| Парткод: | E0-12842000 |
| Деталь: | AJ8W200WWF |
| Парткод: | E0-08497000 |
| Деталь: | HRNS-LVPS-282 |
| Парткод: | 6LE63354000 |
| Деталь: | SPSN-6U |
| Парткод: | F0-00332000 |
| Деталь: | FAN-D-8025-350NH |
| Парткод: | 6LA34342000 |
| Деталь: | SEAL-FAN-280 |
| Парткод: | 6LE57843000 |
| Деталь: | LASER-UNIT-H220 |
| Парткод: | 6LJ48403000 |
| Деталь: | GUIDE-HRNS-DHTR |
| Парткод: | 6LE57845000 |
| Деталь: | LID-BTM-BASE-G |
| Парткод: | 6LJ48222000 |
| Деталь: | CHS-CGC5-28 |
| Парткод: | D0-32012000 |
| Деталь: | FOOT-FRM-BASE |
| Парткод: | 6LE57841000 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | HRNS-FUS-280 |
| Парткод: | 6LE63319000 |
| Деталь: | HRNS-HVPS-SIG-280 |
| Парткод: | 6LE63379000 |
| Деталь: | CABLE-P-INLET-US-15A |
| Парткод: | 6LJ49716000 |
| Деталь: | CABLE-P-INLET-EUR |
| Парткод: | 6LE95822000 |
| Деталь: | CABLE-P-INLET-UK |
| Парткод: | 6LH40421000 |
| Деталь: | CABLE-P-INLET-AU |
| Парткод: | 6LE95823000 |
| Деталь: | CABLE-P-INLET-TWD |
| Парткод: | 6LE95826000 |
| Деталь: | CABLE-P-INLET-CCC-L |
| Парткод: | 6LH23012000 |
| Деталь: | S/TPD3/FHEXM-3X8-ZU3 |
| Парткод: | X0-02593000 |
| Деталь: | S/PAN/SWWP-M4X8-BSNI |
| Парткод: | X0-00169000 |
| Деталь: | RLWS-1TV0 |
| Парткод: | F0-00367000 |
| Деталь: | PS-ACC-152J |
| Парткод: | 6LH93204000 |
| Деталь: | PS-ACC-152E |
| Парткод: | 6LH93205000 |
| Деталь: | GUIDE-LOW-G |
| Парткод: | 6LJ48201000 |
| Деталь: | STOP RING |
| Парткод: | 41306265000 |
| Деталь: | GUIDE-BUSH-RGST-R |
| Парткод: | 6LE57224000 |
| Деталь: | ROLLER-RGST-DRV-284 |
| Парткод: | 6LH23925000 |
| Деталь: | GEAR-10S015-08 |
| Парткод: | 6LE57208000 |
| Деталь: | CLUTCH-G33-08D-30A |
| Парткод: | 6LE57210000 |
| Деталь: | HLDR-SNSR-CSSTT |
| Парткод: | 6LH22010000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | P/PRL/AH7-2X10-SS |
| Парткод: | X0-00980000 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | CS1A-B2CA |
| Парткод: | E0-01853000 |
| Деталь: | CASE-FRAME-SFB DV |
| Парткод: | 6LE53404100 |
| Деталь: | ASYS-SHAFT-RLR-FEED_D |
| Парткод: | 6LH21840000 |
| Деталь: | COUPL-SHAFT-FEED_D |
| Парткод: | 6LH21842000 |
| Деталь: | BUSH-5X8X4R2F-POM |
| Парткод: | 6LE53441000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | BUSH-5X8X4R2F-GCB-NU4 |
| Парткод: | 6LH23440000 |
| Деталь: | STUD-CLUCH-PICK |
| Парткод: | 6LE53467000 |
| Деталь: | GEAR-08S20-5 |
| Парткод: | 6LE53434000 |
| Деталь: | GEAR-08S23-5 |
| Парткод: | 6LE53435000 |
| Деталь: | ASYS-GEAR-GUIDE |
| Парткод: | 6LE53459000 |
| Деталь: | PAWL-ARM-B |
| Парткод: | 6LE53427000 |
| Деталь: | SPG-PAWL-RCHT |
| Парткод: | 6LE53469000 |
| Деталь: | PAWL-ARM-A |
| Парткод: | 6LE53429000 |
| Деталь: | SOL-06A-FED-280 |
| Парткод: | 6LE56678000 |
| Деталь: | SPG-SOL-FEED |
| Парткод: | 6LE53465000 |
| Деталь: | ARM-CAM-LINK |
| Парткод: | 6LE53503000 |
| Деталь: | ARM-PICK |
| Парткод: | 6LE53405000 |
| Деталь: | GEAR-06S29-6 |
| Парткод: | 6LE53413000 |
| Деталь: | ASYS-SHAFT-A |
| Парткод: | 6LE53494000 |
| Деталь: | ASYS-ROL-PICK-371 |
| Парткод: | 6LA79037000 |
| Деталь: | SHAFT-PICK |
| Парткод: | 6LE53417000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | BUSH-5X8X6R2F-POM |
| Парткод: | 6LE53430000 |
| Деталь: | RR/E-5-POM |
| Парткод: | 6LE53442000 |
| Деталь: | HLDR-STOP-BYP |
| Парткод: | 6LE53408000 |
| Деталь: | ARM-STOP |
| Парткод: | 6LE53444000 |
| Деталь: | LEVER-STOP-L |
| Парткод: | 6LE53414000 |
| Деталь: | LEVER-STOP-R |
| Парткод: | 6LE53416000 |
| Деталь: | STOPPER-L |
| Парткод: | 6LE53412000 |
| Деталь: | STOPPER-R |
| Парткод: | 6LE53410000 |
| Деталь: | SPG-RLR-PICK |
| Парткод: | 6LE53464000 |
| Деталь: | ASYS-GUIDE-COVER |
| Парткод: | 6LE53496000 |
| Деталь: | COVER-FRAM-FEED-DV |
| Парткод: | 6LJ46700100 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | BOSS-CLUCH-FEED |
| Парткод: | 6LE53433000 |
| Деталь: | SPG-CLUCH-FEED |
| Парткод: | 6LE53462000 |
| Деталь: | CAP-CLUCH-FEED |
| Парткод: | 6LE53425000 |
| Деталь: | GEAR-CLUCH-FEED |
| Парткод: | 6LE53426000 |
| Деталь: | ASYB-CLUCH-PICK |
| Парткод: | 6LE53487000 |
| Деталь: | CUSHION-COV-BYP-1T11 |
| Парткод: | 6LE53501000 |
| Деталь: | CUSHION-HLDR-BYP-2T11 |
| Парткод: | 6LE53502000 |
| Деталь: | S/BID-M3X8-NI |
| Парткод: | X0-00434000 |
| Деталь: | UAMS-05-0 |
| Парткод: | F0-01048000 |
| Деталь: | ASYS-CASE-DEV-280 |
| Парткод: | 6LE55918000 |
| Деталь: | PLATE-SIDE |
| Парткод: | 6LA81632000 |
| Деталь: | S/FHEXM-M3X10-NI |
| Парткод: | X0-02232000 |
| Деталь: | MIXER-1-371 |
| Парткод: | 6LA81635000 |
| Деталь: | SPACER-MIX |
| Парткод: | 6LA81636000 |
| Деталь: | ASYS-MIXER-2-284 |
| Парткод: | 6LH23230000 |
| Деталь: | MIXER-3-371 |
| Парткод: | 6LA81643000 |
| Деталь: | BUSH-DEV-R-280 |
| Парткод: | 6LE55966000 |
| Деталь: | SEAL-BUSH-DEV-R |
| Парткод: | 6LE55967000 |
| Деталь: | S/TPP/BID-3*8-NI |
| Парткод: | 6LA80090000 |
| Деталь: | SEAL-VC6-10-2.5 |
| Парткод: | 4401949290 |
| Деталь: | BUSH-6X12X4R8F-NU4 |
| Парткод: | 6LH23441000 |
| Деталь: | ASYS-BUSH-0613-07 |
| Парткод: | 6LA81645000 |
| Деталь: | ROLLER-MG-377 |
| Парткод: | 6LH23270000 |
| Деталь: | BUSH-DEV |
| Парткод: | 6LA81652000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | ROLL-GUIDE-371 |
| Парткод: | 6LA81662000 |
| Деталь: | ASYS-BKT-DEV-TENS |
| Парткод: | 6LA81678000 |
| Деталь: | COLLAR-DEV-TENS |
| Парткод: | 4401950980 |
| Деталь: | PULLY-2GT16-6 |
| Парткод: | 6LA81670000 |
| Деталь: | PULLY-2GT27-6 |
| Парткод: | 6LA81666000 |
| Деталь: | P/PRL/AH7-2X10-SS |
| Парткод: | X0-00980000 |
| Деталь: | BLT/T-2GT-92 |
| Парткод: | 6LA81674000 |
| Деталь: | GEAR-10S27-CUP |
| Парткод: | 6LA81677000 |
| Деталь: | GR-10H27-5-06 |
| Парткод: | 4402439380 |
| Деталь: | ASYS-DOCTOR-371 |
| Парткод: | 6LA81656000 |
| Деталь: | BRKT-DEV-R-371 |
| Парткод: | 6LA81691000 |
| Деталь: | F126ZZ-SH44M-GV22 |
| Парткод: | F0-01946000 |
| Деталь: | BRKT-DEV-F-371 |
| Парткод: | 6LA81711000 |
| Деталь: | ADJUSTER-MG |
| Парткод: | 6LA81718000 |
| Деталь: | S/TPD3/FHEXM-3X8-ZU3 |
| Парткод: | X0-02593000 |
| Деталь: | SPL-DOCTOR |
| Парткод: | 6LH53468000 |
| Деталь: | SPC060-065-0130 |
| Парткод: | 4400672520 |
| Деталь: | SCREW-DOCTOR-371 |
| Парткод: | 6LA81610000 |
| Деталь: | GEAR-10S28-6 |
| Парткод: | 6LA81724000 |
| Деталь: | ASYS-BRKT-DRV |
| Парткод: | 6LA81729000 |
| Деталь: | SNR-ATC-280 |
| Парткод: | 6LE63990000 |
| Деталь: | HRNS-ATS-280 |
| Парткод: | 6LE63301000 |
| Деталь: | S/BID-M3X5-BSNI |
| Парткод: | X0-01725000 |
| Деталь: | THMS-DRM-364 |
| Парткод: | 6LE78194000 |
| Деталь: | GEAR-10B22-6 |
| Парткод: | 6LA81685000 |
| Деталь: | ASYS-BRKT-RECY |
| Парткод: | 6LE55970000 |
| Деталь: | GEAR-8S15-6 |
| Парткод: | 6LA81888000 |
| Деталь: | GEAR-8S29_8S18-6 |
| Парткод: | 6LE55980000 |
| Деталь: | GEAR-10B22-6-CUP |
| Парткод: | 6LA81881000 |
| Деталь: | SHEET-MG-F |
| Парткод: | 6LA81780000 |
| Деталь: | SHEET-MG-R |
| Парткод: | 6LA81781000 |
| Деталь: | ASYS-COV-DEV |
| Парткод: | 6LA81790000 |
| Деталь: | COVER-DEV-BTL-371 |
| Парткод: | 6LA81700000 |
| Деталь: | S/PAN/SWWP-M3X8-NI |
| Парткод: | X0-00077000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | MYLAR-DOC-SLIDE |
| Парткод: | 6LA81714000 |
| Деталь: | SCREW-SPG-TR2 |
| Парткод: | 6LE46468000 |
| Деталь: | MOTR_S-SCN-280 |
| Парткод: | 6LE63997000 |
| Деталь: | PLT-MOT-SCAN |
| Парткод: | 6LE60636000 |
| Деталь: | HRNS-SCN-MOT-280 |
| Парткод: | 6LE63385000 |
| Деталь: | BRKT-MOT-SCAN |
| Парткод: | 6LE60634000 |
| Деталь: | BELT-E2M-276-4 |
| Парткод: | 6LE60686000 |
| Деталь: | PLT-SFT-HLDR |
| Парткод: | 6LE60626000 |
| Деталь: | ASYS-BELT-TENSION |
| Парткод: | 6LJ49001000 |
| Деталь: | MYLAR-GLASS |
| Парткод: | 6LE60718000 |
| Деталь: | BRKT-HP-SENSOR |
| Парткод: | 6LE60845000 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 6LA08937000 |
| Деталь: | BELT-E2M-1290-4 |
| Парткод: | 6LE60682000 |
| Деталь: | PLY-TENSION-12 |
| Парткод: | 6LE60654000 |
| Деталь: | Spring-Tension |
| Парткод: | 6LE60678000 |
| Деталь: | PULLEY-30STE2 |
| Парткод: | 6LE60662000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | PULLEY-40_S16STE2 |
| Парткод: | 6LE60670000 |
| Деталь: | S/PAN-M3X4-NI |
| Парткод: | X0-02113000 |
| Деталь: | UAMS-02WL-0 |
| Парткод: | F0-01046000 |
| Деталь: | S/TPD3/FHEXM-3X6-ZU3 |
| Парткод: | X0-02592000 |
| Деталь: | S/TPD3/FHEXM-3X8-ZU3 |
| Парткод: | X0-02593000 |
| Деталь: | LG248NL1 |
| Парткод: | C0-11250000 |
| Деталь: | ASYS-COV-REAR |
| Парткод: | 6LE55205000 |
| Деталь: | COVER-SCAN-FRT-H DV |
| Парткод: | 6LE54674100 |
| Деталь: | COV-TOP-SCAN-DV |
| Парткод: | 6LH91600100 |
| Деталь: | LID-COV-REAR_DF |
| Парткод: | 6LE55290000 |
| Деталь: | LID-COV-REAR_PRT |
| Парткод: | 6LE55291000 |
| Деталь: | ASYB-BOOK-HOLDER-CJ2 |
| Парткод: | 6LH22722000 |
| Деталь: | LID-COV-REAR-PFU |
| Парткод: | 6LE55294000 |
| Деталь: | S/TPD3/FHEXM-3X8-ZU3 |
| Парткод: | X0-02593000 |
| Деталь: | S/TPD3/FHEXM-4X8-ZU3 |
| Парткод: | X0-02589000 |
| Деталь: | LBL-LASER |
| Парткод: | 6LA47529000 |
| Деталь: | LBL-LASER-C |
| Парткод: | 6LA56226000 |
| Деталь: | LBL-LASER-TWD |
| Парткод: | 6LA48505000 |
| Деталь: | CASE-ADU-JE DV |
| Парткод: | 6LE56901100 |
| Деталь: | PUSHER-CASE-ADU-SW |
| Парткод: | 6LE57000000 |
| Деталь: | LVR-OPEN-COV-SID DV |
| Парткод: | 6LE56910100 |
| Деталь: | COVER-EXIT-CJ DV |
| Парткод: | 6LE56960100 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | SPG-COVER-EXIT |
| Парткод: | 6LE56921000 |
| Деталь: | STOPPER-STRING-F-282 |
| Парткод: | 6LE57011000 |
| Деталь: | STOPPER-STRING-R-280 |
| Парткод: | 6LE56990000 |
| Деталь: | PUSHER-COV-SIDE |
| Парткод: | 6LE56950000 |
| Деталь: | LBL-O-PLACE-COV-280 |
| Парткод: | 6LE57020000 |
| Деталь: | LBL- W-HOT-EXIT371 |
| Парткод: | 6LA82504000 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | S/TPS/FPAN-3X25-ZU3 |
| Парткод: | X0-02426000 |
| Деталь: | LBL-HOT-COV |
| Парткод: | 6LA75470000 |
| Деталь: | LBL-HOT-COV-TWD |
| Парткод: | 6LA75503000 |
| Деталь: | CASE-CH-M |
| Парткод: | 6LA84920000 |
| Деталь: | CH-M |
| Парткод: | 6LH25001000 |
| Деталь: | GRID-CH-M-371 |
| Парткод: | 6LA84930000 |
| Деталь: | HANGER-WIRE-TR |
| Парткод: | 4401764730 |
| Деталь: | LID-CH-M-F |
| Парткод: | 6LA84944000 |
| Деталь: | LID-CH-M-R |
| Парткод: | 6LH29501000 |
| Деталь: | MYLAR-CLN-CH |
| Парткод: | 6LA84941000 |
| Деталь: | MYLAR-LED |
| Парткод: | 6LA84957000 |
| Деталь: | ROD-CLN-CH-M |
| Парткод: | 6LA84938000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | SPE-GR |
| Парткод: | 6LA84950000 |
| Деталь: | SPL-CH-M-R |
| Парткод: | 6LA84922000 |
| Деталь: | SPRING-TENS-CH |
| Парткод: | 6LA84935000 |
| Деталь: | TERM-CH-M-R |
| Парткод: | 6LA84915000 |
| Деталь: | TERM-CH-M-F |
| Парткод: | 6LA84910000 |
| Деталь: | ASY-CH-MAIN |
| Парткод: | 6LH25002000 |
| Деталь: | ASYS-COV-NOZLE-280 |
| Парткод: | 6LE56021000 |
| Деталь: | AUGER-RECY-280 |
| Парткод: | 6LE56030000 |
| Деталь: | BUSH-0611-06F-M |
| Парткод: | 6LH89031000 |
| Деталь: | GEAR-8S22-6 |
| Парткод: | 6LA81936000 |
| Деталь: | S/TPP/BID-3*8-NI |
| Парткод: | 6LA80090000 |
| Деталь: | COVER-RECY-280 |
| Парткод: | 6LE56035000 |
| Деталь: | MYLAR-VIB-TNR |
| Парткод: | 6LE56040000 |
| Деталь: | SEAL-RECY-CLN |
| Парткод: | 6LA81953000 |
| Деталь: | MYLAR-RECY-CLN |
| Парткод: | 6LA81952000 |
| Деталь: | ASYS-TNR-IN |
| Парткод: | 6LA81955000 |
| Деталь: | STOPPER-LID-371 |
| Парткод: | 6LA81707000 |
| Деталь: | PUSHER-DEV-G |
| Парткод: | 6LJ48202000 |
| Деталь: | SPC-PUSH-DEV-F |
| Парткод: | 6LA82106000 |
| Деталь: | BRKT-HOLD-SP-280-G |
| Парткод: | 6LJ48204000 |
| Деталь: | SPC-PUSH-DEV-R |
| Парткод: | 6LA82107000 |
| Деталь: | BRKT-SNSR-280 |
| Парткод: | 6LE53708000 |
| Деталь: | ACTR-SNSR-280 |
| Парткод: | 6LE53709000 |
| Деталь: | ASYS-GUIDE-RGST-L-G |
| Парткод: | 6LJ48205000 |
| Деталь: | ASYS-GUIDE-MYLAR-RGST-G |
| Парткод: | 6LJ48221000 |
| Деталь: | HRNS-RGST-SW-280 |
| Парткод: | 6LE63358000 |
| Деталь: | ACTR-RGST-280 |
| Парткод: | 6LE57204000 |
| Деталь: | SPG-ACT-RGST |
| Парткод: | 6LE57220000 |
| Деталь: | MYLAR-SUPPORT-SNS |
| Парткод: | 6LA85910000 |
| Деталь: | S/TPS/FHEXM/R-3X8-ZU3 |
| Парткод: | X0-02420000 |
| Деталь: | UAMS-05SN-W |
| Парткод: | F0-00043000 |
| Деталь: | UAMS-02WL-0 |
| Парткод: | F0-01046000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | LG248NL1 |
| Парткод: | C0-11250000 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | ASYS-FRAME-CLN-C |
| Парткод: | 6LA79525000 |
| Деталь: | ASYS-FRAME-CLN-F |
| Парткод: | 6LA79540000 |
| Деталь: | FRAME-CLN-R |
| Парткод: | 6LA79583000 |
| Деталь: | AUGER-CLN |
| Парткод: | 6LA79600000 |
| Деталь: | BL-2320D |
| Парткод: | 6LA27845000 |
| Деталь: | BLADE-REC |
| Парткод: | 6LE54020000 |
| Деталь: | BUSH-0410-05F-M |
| Парткод: | 6LA02920000 |
| Деталь: | GEAR-10S18-4 |
| Парткод: | 6LA79605000 |
| Деталь: | GEAR-10S17-4 |
| Парткод: | 6LA79606000 |
| Деталь: | HLDR-LED |
| Парткод: | 6LH23220000 |
| Деталь: | HOLDER-SCRAPER |
| Парткод: | 6LA79615000 |
| Деталь: | PWA-F-DLE-280V |
| Парткод: | 6LH27027000 |
| Деталь: | SEAL-BLADE-SIDE |
| Парткод: | 6LA79547000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | SCRAPER-371 |
| Парткод: | 6LA79618000 |
| Деталь: | SEAL-CLN-F |
| Парткод: | 6LA79546000 |
| Деталь: | SEAL-CLN-R |
| Парткод: | 6LA79586000 |
| Деталь: | MYLAR-HLDR-LED |
| Парткод: | 6LH29503000 |
| Деталь: | SEAL-CLN-C |
| Парткод: | 6LA79531000 |
| Деталь: | SHUTTER-CLN |
| Парткод: | 6LA79609000 |
| Деталь: | SPC-NZL-CLN |
| Парткод: | 6LA79612000 |
| Деталь: | STUD-GEAR-CLN |
| Парткод: | 6LA79554000 |
| Деталь: | WHEEL-CLN-8 |
| Парткод: | 41306325000 |
| Деталь: | SEAL-SIDE-REC |
| Парткод: | 6LA79534000 |
| Деталь: | BUSH-1821*03-M |
| Парткод: | 41306135000 |
| Деталь: | PIN-DRUM-371 |
| Парткод: | 6LA79622000 |
| Деталь: | SPD-SCRPR-DRUM |
| Парткод: | 41305536000 |
| Деталь: | HRNS-DLE2-377 |
| Парткод: | 6LE88066000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | S/TPP/BID-3*8-NI |
| Парткод: | 6LA80090000 |
| Деталь: | RR/E-2.5-SS |
| Парткод: | X0-00974000 |
| Деталь: | SCREW-CLNR-DEV |
| Парткод: | 6LA65682000 |
| Деталь: | SCREW-PU-F_M |
| Парткод: | 6LH23250000 |
| Деталь: | COV-PU-F-U_N |
| Парткод: | 6LH89000100 |
| Деталь: | COV-PU-F-J_N |
| Парткод: | 6LH89000000 |
| Деталь: | COV-PU-F-D_N |
| Парткод: | 6LH89000300 |
Коды ошибок
C01
C04
C08
C15
C16
C21
C26
C41
C43
C44
C45
C55
C56
C94
C97
C99
CA1
CA2
E01
E02
E03
E09
E11
E12
E13
E14
E15
E16
E21
E30
E32
E33
E35
E36
E40
E41
E42
E44
E51
E71
E72
E73
E74
E86
E87
F14
Описание
| Error code: | C01 |
| Display: | C01-xxx No Ink Replace Ink Cartridge |
| Description: | Main motor is abnormal |
| Remedy: | Is the main motor working? NO 1. Check if the connector CN1 of the main motor is disconnected. 2. Check if the connector J313 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circutied. 4. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 5. Replace the main motor. 6. Replace the LGC board. YES Is the LED on the main motor board lit without flickering? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 3. Replace the main motor. 4. Replace the LGC board. YES 1. Check if the PLL lock signal J313-11 output from the LGC board is always level “L”? 2. Check if the voltage supplied to the microcomputer input terminal IC10-7 is always “L”? 3. Replace the LGC board. |
| Error code: | C04 |
| Display: | C04-xxx Add Paper |
| Description: | Abnormal feed motor |
| Causes: | 402 Paper detection sensor is OFF (not detecting paper). |
| Remedy: | Is the PFP motor working? (Perform the output check in the test mode: 03-125/175) NO 1. Check if the signal line connector of the feed motor is disconnected. 2. Check if the connector J327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the feed motor board and LGC board are short- or open circuited. 5. Replace the feed motor. 6. Replace the LGC board. YES Is the LED on the feed motor board lit without flashing? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the feed motor board and LGC board are short- or open-circuited. 3. Replace the feed motor. 4. Replace the LGC board. YES Replace the LGC board. |
| Error code: | C08 |
| Description: | ADU motor IC overcurrent detection error |
| Causes: | 861 No paper is set on the standard paper feed tray while the tray is specified as interposer tray by the Admin. Tab on the operation panel. |
| Remedy: | 1 Is the ADU motor working? (Perform the output check in the test mode: 04-110/160) Yes 2 No 1. Check if any of the connectors CN251 and CN252 on the ADU board is disconnected. 2. Check if the relay connector between the ADU board and the PFC board is disconnected. 3. Check if the connector CN246 on the PFC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the ADU board and the PFC board are short circuited or open circuited. 6. Replace the ADU motor. 7. Replace the ADU board. 8. Replace the PFC board. 2 Is the voltage supplied to the driver IC terminal IC1-18 on the ADU board is always at level "H"? Yes 3 No 1. Check if the voltage supplied to the connector CN251-12 on the ADU board is always at level "H". 2. Check if the voltage supplied to the connector CN246-6 on the PFC board is always at level "H". 3. Check if the voltage supplied to the CPU input terminal (IC4-96) on the PFC board is always at level "H". 4. Replace the PFC board. 3 Replace the ADU board. |
| Error code: | C15 |
| Description: | 3rd cassette tray operation abnormal |
| Remedy: | Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board. |
| Error code: | C16 |
| Description: | 4th cassette tray operation abnormal |
| Remedy: | Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board. |
| Error code: | C21 |
| Description: | Carriage initialization error |
| Remedy: | 1 Does the CIS case move to its home position when the power is turned ON? Yes 1. Check if the CIS home position sensor is installed properly. 2. Check if any of the connectors is disconnected from the CIS home position sensor. 3. Check if the connector CN14 on the MAIN board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the MAIN board are short circuited or open circuited. 6. Replace the CIS home position sensor. 7. Replace the MAIN board. No 2 2 Is there any abnormal sound when the CIS case is moving? Yes 1. Check if the CIS unit drive belt-1 or the CIS unit drive belt-2 is damaged. 2. Check if the belt tension of the CIS unit drive belt-1 or the CIS unit drive belt-2 is loose. 3. Check if the joint of the belt stopper and the CIS unit drive belt-1 is loose. No 3 3 1. Check if the tension of the CIS unit drive belt-1 or the CIS unit drive belt-2 is too tight. 2. Check if any of the connectors of the scan motor is disconnected. 3. Check if the connector CN18 on the MAIN board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the MAIN board are short circuited or open circuited. 6. Replace the scan motor. 7. Replace the MAIN board |
| Error code: | C26 |
| Description: | Peak detection error |
| Remedy: | Does the exposure lamp light? (Perform the output check in the test mode: 03-267) YES 1. Check if the connectors on the CCD and SLG boards are disconnected. 2. Check if the shading correction plate is dirty. 3. Check if the conductor pattern on the CCD board is short- or open-circuited. 4. Check if the conductor pattern on the SLG board is short- or open-circuited. 5. Replace the lens unit. 6. Replace the SLG board. NO 1. Check if the connectors of the exposure lamp and inverter are disconnected. 2. Check the SLG board if the connector pin J9 is disconnected and the harness is short- or opencircuited. 3. Check if the conductor pattern on the SLG board is short- or open-circuited. 4. Replace the SLG board. 5. Replace the inverter. 6. Replace the exposure lamp. |
| Error code: | C41 |
| Description: | Thermistor or heater abnormal when warming-up is started |
| Causes: | MAIN board Switching regulator |
| Remedy: | 1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally. |
| Error code: | C43 |
| Description: | Thermistor abnormal during warming-up after abnormality judgment |
| Causes: | MAIN board Switching regulator |
| Remedy: | 1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally. |
| Error code: | C44 |
| Description: | Heater abnormal during warming-up after abnormality judgment |
| Causes: | MAIN board Switching regulator |
| Remedy: | 1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally. |
| Error code: | C45 |
| Description: | Abnormal side thermistor after the copier has become ready |
| Causes: | MAIN board Switching regulator |
| Remedy: | 1. Check the side thermistor (1) Check if the connector is disconnected. (2) Check if the side thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the side thermistor is open-circuited. 2. Check the LGC board (1) Check if the connector J334 is disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) “6” to “0”. |
| Error code: | C55 |
| Description: | RADF I/F error |
| Remedy: | Is the harness between the ADF board and SLG board open-circuited? Replace the harness. Is the ADF board short- or open-circuited? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. Replace the SLG board. |
| Error code: | C56 |
| Description: | Communication error between main CPU and PFC |
| Causes: | • If the ADF unit set sensor does not detect the ADF unit. |
| Remedy: | (1) Check if the conductor pattern around IC57 and IC58 is not short- or open-circuited. (2) Replace the LGC board. |
| Error code: | C94 |
| Description: | LGC-CPU abnormal |
| Remedy: | Is "Call for service" displayed again even after the copier is turned OFF and then back ON? N: Observe the condition for a while. Y: 1. Check if the conductor pattern between LGC-CPU (IC32) and FROM (IC24) is open- or short-circuited. 2. If this problem recurs frequently, replace the LGC board. |
| Error code: | C97 |
| Description: | Vacuum fan motor abnormality |
| Remedy: | Check the High-voltage transformer. 1. Is the main charger installed securely? 2. Check if the spring of high-voltage supply contact point is deformed. 3. Check if the needle electrode is broken or the main charger grid is deformed. 4. Check if any foreign matters is on the needle electrode or the main charger grid. 5. Is the transfer/separation charger installed securely? 6. Check if the transfer/separation charger wire is broken or unhooked. 7. Check if any foreign matter is on the transfer/separation charger wire. |
| Error code: | C99 |
| Description: | PFC microcomputer is abnormal |
| Remedy: | Is the service call output even after the power switch on the main unit is turned OFF then ON again? No Leave as it is and see what happens. Yes • Check the circuit pattern around the PFC microcomputer (IC21) for breaks and short-circuits. • Replace the PFC microcomputer or LGC board if this trouble occurs frequently. |
| Error code: | CA1 |
| Description: | Polygonal motor rotation abnormal |
| Remedy: | Is the polygonal motor rotating? N: 1. Check if the polygonal motor connector is disconnected. 2. Check if connector J181 or J188 on the IMC board is disconnected. 3. Check if any harness is open-circuited or any connector pin is disconnected. 4. Check if any conductor pattern on the IMC board is open- or short-circuited. 5. Replace the IMC board. 6. Replace the laser optical unit. Y: Are both 10th and 12th pins of the connector J188 on the IMC board always at the level "L"? N: 1. Check if any conductor pattern on the IMC board is open- or short-circuited . 2. Replace the IMC board. 3. Replace the laser optical unit. Y: 1. Check if any conductor pattern on the IMC board is open- or short-circuited . 2. Replace the IMC board. 3. Replace the laser optical unit. |
| Error code: | CA2 |
| Description: | H-SYNC abnormal |
| Remedy: | Is the polygonal motor rotating? N: Refer to "[CA1] Polygonal motor rotation abnormal". Y: Are both 10th and 12th pins of the connector J188 on the IMC board always at the level "L"? N: Refer to "[CA1] Polygonal motor rotation abnormal". Y: Is the harness between the RLY and IMC boards open-circuited? Are the connector J185 on the IMC board or the connector J201 on the RLY board disconnected? Y: Replace the harness. Reconnect the connectors. N: 1. Replace the IMC board. 2. Replace the laser optical unit. |
| Error code: | E01 |
| Description: | Paper leading edge not reaching the exit sensor |
| Remedy: | Is the fuser motor rotating? Y: Is the harness between the LGC board and the exit sensor open-circuited? Is the connector of the paper exit sensor or the connector J123 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the exit sensor. 2. Replace the LGC board. N: Is the harness between the LGC board and the paper exit sensor open-circuited? Is the fuser motor connector or the connector J122 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the fuser motor. 2. Replace the LGC board. Where was the paper stopped? Near the exit sensor (paper not damaged) Are the registration seRemove the paper after the fuser unit cools down.nsor and paper exit sensor functioning properly? (Does the actuator return normally?) Y: 1. In the tRemove the paper after the fuser unit cools down.est mode (03) check if each sensor is functioning. 2. Reconnect each sensor connector. N: Repair the actuator if it has come off. Before reaching the fuser unit Did the paper stop, curling upward excessively? Y: Replace the paper in the cassette. From the transfer belt surface to the exit sensor Do the size of paper and the size set match? N: Make the sizes match. Y: Is the transfer belt moving? Is the black drum motor or the transfer belt motor stopped? Or is any abnormal noise heard from one of them due to loss of synchronism? Y: 1. Reduce the mechanical load by adjusting the drive system. Remove any foreign matter. 2. Check the motor connector, and the connector J130 on the LGC board. 3. Replace the motor. 4. Replace the LGC board. No paper found Is the paper attached to the fuser belt? Remove the paper after the fuser unit cools down. |
| Error code: | E02 |
| Display: | E02-xxx !!Maintenance!! Call Service |
| Description: | Paper trailing edge not passing the exit sensor |
| Remedy: | Is the fuser motor rotating? Y: Is the harness between the LGC board and the exit sensor open-circuited? Is the connector of the paper exit sensor or the connector J123 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the exit sensor. 2. Replace the LGC board. N: Is the harness between the LGC board and the paper exit sensor open-circuited? Is the fuser motor connector or the connector J122 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the fuser motor. 2. Replace the LGC board. Where was the paper stopped? Near the exit sensor (paper not damaged) Are the registration seRemove the paper after the fuser unit cools down.nsor and paper exit sensor functioning properly? (Does the actuator return normally?) Y: 1. In the tRemove the paper after the fuser unit cools down.est mode (03) check if each sensor is functioning. 2. Reconnect each sensor connector. N: Repair the actuator if it has come off. Before reaching the fuser unit Did the paper stop, curling upward excessively? Y: Replace the paper in the cassette. From the transfer belt surface to the exit sensor Do the size of paper and the size set match? N: Make the sizes match. Y: Is the transfer belt moving? Is the black drum motor or the transfer belt motor stopped? Or is any abnormal noise heard from one of them due to loss of synchronism? Y: 1. Reduce the mechanical load by adjusting the drive system. Remove any foreign matter. 2. Check the motor connector, and the connector J130 on the LGC board. 3. Replace the motor. 4. Replace the LGC board. No paper found Is the paper attached to the fuser belt? Remove the paper after the fuser unit cools down. |
| Error code: | E03 |
| Description: | Paper remaining inside the copier at power ON |
| Remedy: | Is any paper remaining inside the copier? Y: Remove the paper. N: Refer to [E01], [E02] and [E11] to [E26]. |
| Error code: | E09 |
| Description: | Jam caused by an abnormal HDD |
| Remedy: | (1) Check if the connectors of the HDD are disconnected. (2) Check if the connector pins are disconnected and the harnesses are open-circuited. (3) Replace the HDD. (4) Replace the SYS board. |
| Error code: | E11 |
| Description: | Paper misfeed from the ADU |
| Remedy: | Is any paper remaining in the paper feed area inside the ADU? Y: Remove the paper. N: Is the connector J104 on the LGC board disconnected? Is the harness between the LGC board and the ADU drawer connector open-circuited? Y: Reconnect the connector. Replace the harness. N: 1. Replace the LGC board. 2. Replace the ADU. |
| Error code: | E12 |
| Display: | E12-Output Bin Full, Top |
| Description: | Top Output Tray is Full, Unload Paper |
| Remedy: | 1 Visually inspect the Stack Full Actuator and use service diagnostics to test the Stack Full Sensor. Does the sensor and actuator operate correctly? Go to step [3]. Replace the actuator if broken. If the sensor is not working, go to step [2}. 2 Check Pin 6 OPTN cable at the Engine Controller Board for +5 volts. Replace the Engine Controller Board. Go to step [3]. 3 Check the Stack Full Sensor wiring harness to the Toner Sensor Board Pin 3 for +5 volts. Go to step [4]. Replace the Stack Full Sensor and wiring. 4 Check for +5 volts at Pin 6 OPTN cable to the Toner Sensor Board. Replace the ribbon cable (OPTN) Replace the Toner Sensor Board. |
| Error code: | E13 |
| Description: | Paper misfeed from the 1st cassette |
| Remedy: | Open the side door; does any paper remain in the paper path from the cassette? Y: Remove the paper. N: Is the width of the side guide set too narrow for the paper width? Y: Set the side guide wider. (When the tray is being lifted, make sure that a gap is left between the paper and the side guide.) N: Is the harness between the LGC board and the cassette feed-jam sensor open-circuited? Is the cassette feed-jam sensor connector or the connector J106 or J107 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the cassette feed-jam sensor. 2. Replace the LGC board. |
| Error code: | E14 |
| Display: | E14-Front Cover B Open |
| Description: | The front cover (Cover B) is open. Close the cover so that printing can continue. |
| Remedy: | 1. Ensure the duplexer is installed correctly. 2. Inspect the connector at the rear end of the duplexer unit. 3. Inspect the wiring harness leading from the duplexer unit interface connector to the engine controller board. 4. Replace the duplexer unit. 5. Replace the engine controller board. |
| Error code: | E15 |
| Description: | Paper misfeed from the 3rd cassette |
| Causes: | • If the light path of the Master tension plate sensor is not blocked within 384 pulse rotation of the Read pulse motor rotated in the reverse direction. • If master loading error is detected at Drum angle 79° and if the Master tension plate sensor is blocked. |
| Remedy: | Open the side door; does any paper remain in the paper path from the cassette? Y: Remove the paper. N: Is the width of the side guide set too narrow for the paper width? Y: Set the side guide wider. (When the tray is being lifted, make sure that a gap is left between the paper and the side guide.) N: Is the harness between the LGC board and the cassette feed-jam sensor open-circuited? Is the cassette feed-jam sensor connector or the connector J106 or J107 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the cassette feed-jam sensor. 2. Replace the LGC board. |
| Error code: | E16 |
| Description: | Paper misfeed from the 4th cassette |
| Causes: | • If excessive current is detected 0.3 seconds consecutively after the Inking motor is activated. |
| Remedy: | Open the side door; does any paper remain in the paper path from the cassette? Y: Remove the paper. N: Is the width of the side guide set too narrow for the paper width? Y: Set the side guide wider. (When the tray is being lifted, make sure that a gap is left between the paper and the side guide.) N: Is the harness between the LGC board and the cassette feed-jam sensor open-circuited? Is the cassette feed-jam sensor connector or the connector J106 or J107 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the cassette feed-jam sensor. 2. Replace the LGC board. |
| Error code: | E21 |
| Description: | Paper transport jam from the LCF |
| Remedy: | Open the side door; does any paper remain in the paper path up to the registration roller? Y: Remove the paper. N: Is the harness between the LGC board and the cassette feed-jam sensor open-circuited? Is the harness between the LGC board and the registration sensor open-circuited? Is the cassette feed-jam sensor connector, registration sensor connector, or the connector J107 or J108 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the cassette feed-jam sensor or the registration sensor. 2. Replace the LGC board. |
| Error code: | E30 |
| Description: | Paper fed from the 3rd cassette (not reaching the registration sensor) |
| Causes: | The Developer Unit is not connected to the machine. |
| Error code: | E32 |
| Description: | Paper fed from the 3rd cassette (not reaching the 2nd cassette transport sensor) |
| Causes: | The Upper Size Selector is having some error. |
| Remedy: | Open the feed cover. Is there paper in front of the 2nd cassette transport sensor? YES Remove the paper. NO Is the 2nd cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[3]/[B]) NO 1. Check if the connector of the 2nd cassette transport sensor is disconnected. 2. Check if the connector J328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 2nd cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-203, 210, 226) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out. |
| Error code: | E33 |
| Description: | Paper fed from the 3rd cassette (not reaching the 3rd cassette transport sensor) |
| Causes: | The Lower Size Selector is having some error. |
| Remedy: | Open the feed cover. Is there any paper in front of the 3rd cassette transport sensor? YES Remove the paper. NO Is the 3rd cassette tranport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[4]/[B] NO 1. Check if the connector of the 3rd cassette transport sensor is disconnected. 2. Check if the connector J328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5 Replace the 3rd cassette transport sensor. 6. Replace the LGC board. YES Is the transport clutch working? (Perform the output check in the test mode: 03-225) NO 1. Check if the connector of the transport clutch is disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5 Replace the transport clutch. 6 Replace the LGC board. YES Check the transport roller. Replace it if it is worn out. |
| Error code: | E35 |
| Description: | Paper fed from the 4th cassette (not reaching the 1st cassette transport sensor) |
| Causes: | The Fuser Blower 1 (BL1) on the driving side is not working correctly. |
| Remedy: | Open the feed cover. Is there paper in front of the 1st cassette transport sensor? YES Remove the paper. NO Is the 1st cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) NO 1. Check if the connector of the 1st cassette transport sensor is disconnected. 2. Check if the connector J328, 329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-202, 203, 210) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out. |
| Error code: | E36 |
| Description: | Paper fed from the 4th cassette (not reaching the 2nd cassette transport sensor) |
| Causes: | The Paper Feeding Blower (BL3) is not working correctly. |
| Error code: | E40 |
| Description: | Jam access cover opened during printing |
| Remedy: | Is the jam access cover open? YES Remove paper if there is any, then shut the cover. NO Is the voltage of 24V being supplied from the power supply unit? (Perform the input check in the test mode: 03-[FAX] ON/[1]/[H]) NO 1. Check if the connector for 24V power supply is disconnected. 2. Check if the connector J319 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Replace the LGC board. |
| Error code: | E41 |
| Description: | Front cover opened during printing |
| Remedy: | Is the front cover or the paper-exit unit open? Y: Close the front cover or the paper-exit unit. N: Is the AC harness between the main switch, front cover switch, paper-exit unit switch and switching power supply open-circuited? Is any of the faston terminals (front cover switch, paper-exit unit switch, main switch) and the connector J701 of the switching power supply disconnected? Y: Reconnect the disconnected faston terminal or connector. Replace the harness. N: 1. Replace the front cover switch or the paper-exit unit switch. 2. Replace the main switch. 3. Replace the switching power supply. |
| Error code: | E42 |
| Description: | Side door opened during printing |
| Causes: | The temperature on the side of the Fuser Roller is risen abnormally. |
| Remedy: | Is the side door open? Y: Close the side door. N: Is the harness between the LGC board and the side door open/close switch open-circuited? Is the side door open/close switch connector or the connector J107 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the side door open/close switch. 2. Replace the LGC board. |
| Error code: | E44 |
| Description: | Feed cover opened during printing |
| Remedy: | Is the feed cover open? YES Remove the paper if there is any, then close the cover. NO Is the feed cover sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[4]/[G]) NO 1. Check if the connector of the feed cover sensor is disconnected. 2. Check if the connector J338 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are opencircuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the feed cover sensor. 6. Replace the LGC board. YES Replace the LGC board. |
| Error code: | E51 |
| Description: | Paper not restarting from the ADU stack |
| Remedy: | Is the ADU pushed in securely to the copier? N: Push in the ADU securely to the copier. Y: Is the connector J104 on the LGC board disconnected? Is the harness between the LGC board and the ADU drawer connector open-circuited? Y: Reconnect the connector. Replace the harness. N: 1. Replace the LGC board. 2. Replace the ADU. |
| Error code: | E71 |
| Display: | E71 PRAM DATA ADDR |
| Description: | Original not reaching the aligning sensor |
| Remedy: | Have too many originals been placed? Y: Reset the originals, following the specification. N: Are the original sheets curled or folded too much? Y: Flatten and reset the originals. N: Are different-size originals placed together? Y: Set only one-size originals. N: Is the gap between the aligning plate and the feed roller too large? Y: Adjust the gap. N: Is the separation pad stained? Y: Clean the separation pad. |
| Error code: | E72 |
| Description: | Original not reaching the exit sensor |
| Remedy: | Have too many originals been placed? Y: Reset the originals, following the specification. N: Are the original sheets curled or folded too much? Y: Flatten and reset the originals. N: Are different-size originals placed together? Y: Set only one-size originals. N: Is the gap between the aligning plate and the feed roller too large? Y: Adjust the gap. N: Is the separation pad stained? Y: Clean the separation pad. |
| Error code: | E73 |
| Description: | Original not passing the exit sensor |
| Remedy: | Have too many originals been placed? Y: Reset the originals, following the specification. N: Are the original sheets curled or folded too much? Y: Flatten and reset the originals. N: Are different-size originals placed together? Y: Set only one-size originals. N: Is the gap between the aligning plate and the feed roller too large? Y: Adjust the gap. N: Is the separation pad stained? Y: Clean the separation pad. |
| Error code: | E74 |
| Display: | E74 TRANS DATA |
| Description: | Original reversing jam |
| Remedy: | Are the read roller and reverse roller dirty? YES Clean the rollers. NO Is the reverse flapper working properly? NO Adjust the reverse solenoid. |
| Error code: | E86 |
| Description: | ADF jam. ADF jam access cover open: The ADF jam access cover has opened during ADF operation. |
| Remedy: | 1 Is the ADF jam access cover opened? Yes Remove the original, if any, and close the ADF jam access cover. No 2 2 Is the ADF jam access cover switch working? (Perform the input check: 13- [04. SENSOR TEST]) Yes 3 No 1. Check if the connector of the ADF jam access cover switch is disconnected. 2. Check if the connector CN75 on the ADF board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open circuited. 4. Check if the conductor pattern on the ADF board is short circuited or open circuited. 5. Replace the ADF jam access cover switch. 6. Replace the ADF board. 3 Replace the ADF board. |
| Error code: | E87 |
| Description: | ADF jam. ADF open jam: ADF has opened during ADF operation. |
| Remedy: | 1 Is the ADF opened? Yes Remove the original, if any, and close the ADF. No 2 2 Is the ADF opening/closing sensor adjusted within the specified range? Yes 3 No Adjust the ADF opening/closing sensor. 3 Is the ADF opening/closing sensor working? (Perform the input check: 13- [04. SENSOR TEST]) Yes 4 No 1. Check if the connector of the ADF opening/closing sensor is disconnected. 2. Check if the connector CN74 on the ADF board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open circuited. 4. Check if the conductor pattern on the ADF board is short circuited or open circuited. 5. Replace the ADF opening/closing sensor. 6. Replace the ADF board. 4 Replace the ADF board. |
| Error code: | F14 |
| Description: | Scanner unit F-ROM error |
| Remedy: | 1 Has the MAIN board been replaced? Yes Download the counter value of the SRAM board to the MAIN board in the setting mode (08-389). No 2 2 Has the SRAM board been replaced? Yes Download the counter value of the MAIN board to the SRAM board in the setting mode (08-388). No 3 3 1. Check if the connector CN2 on the SRAM board and the connector CN2 on the MAIN board are securely connected. 2. Replace the SRAM board. 3. Replace the MAIN board. |
