Toshiba e-Studio 210c

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

лазерная

Макс. формат

Скорость печати A4

Цветность печати

цветная

Общие характеристики
Размещение	напольный
Макс. формат	A3
Технология печати	лазерная
Тип	лазерный/светодиодный
Тип устройства	МФУ
Сканер
Копир
Цветность печати	цветная
Телефон
Печать фотографий
Факс
Принтер
Время разогрева	240
Двусторонняя печать
Макс, разрешение для ч/б печати
По Y	600
По X	1 200
Скорость ч/б печати
A4	21
A4	31
Копир
Макс, количество копий за цикл	999
Время выхода первой копии	9
Шаг масштабирования	0,01
Значение масштаба
Минимальное	0,25
Максимальное	4
Макс, разрешение (ч/б)
По X	600
По Y	600
Сканер
Макс. формат оригинала	A3
Оттенки серого	256
Устройство автоподачи оригиналов	одностороннее
Расходные материалы
Ресурс фотобарабана	40 000
Ресурс девелопера	40 000
Печать на:
Этикетках
Карточках
Пленках
Плотность бумаги
Максимальная	256
Минимальная	54
Телефон
Caller ID
Беспроводная трубка
Стандарт DECT
Спикерфон
Автоответчик
АОН
Проводная трубка
Лотки
Подача бумаги
Стандартная	1 330
Вывод бумаги
Стандартный	300
Финишер
Сортировка со сдвигом
Сортер
Интерфейсы
Ethernet (RJ-45)
Память/Процессор
Емкость жесткого диска	20
Объем памяти	128
Габариты
Глубина	750
Высота	997
Вес	187
Ширина	868

Модули

ASM-USED-TONER

ASM-FUSER-2

ASM-TBU-TRAY-1

ASM-FEEDER-1

ASM-FUSER-1

ASM-EPU-FRAME

ASM-COVER-2

ASM-BASE-FRAME

ASM-EPU-DEVELOPER-1

ASM-OPTICS-2

ASM-REAR-FRAME-2

ASM-COVER-1

ASM-CRG-2

ASM-CASSETTE

ASM-FUSER-DRIVE

ASM-BYPASS

ASM-CONTROL-PANEL

ASM-EPU-CHARGER

ASM-ELECTRIC

ASM-EPU-DEVELOPER-2

ASM-ADU-GUIDE

ASM-PAPER-EXIT

ASM-SIZE-INDICATOR

ASM-TBU-TRAY-2

ASM-REAR-FRAME-1

ASM-CRG-1

ASM-FEEDER-2

ASM-FEED-DRIVE

ASM-EPU-DRIVE

ASM-OPTICS-1

ASM-LASER-SCAN

ASM-FRONT-FRAME

ASM-TRANSPORT-BELT

ASM-EPU-CLEANER

ASM-ALGINING

ASM-BYPASS-FEEDER

Детали ASM-CONTROL-PANEL

Деталь:	KEY-PRINT
Парткод:	4406306680

Деталь:	KEY-STOP
Парткод:	4406306520

Деталь:	KEY-TEN-31 4
Парткод:	44217311000

Деталь:	KEY-FC
Парткод:	4406505080

Деталь:	KEY-ID-314
Парткод:	4421 731 2000

Деталь:	KEY-FUNC-31 4
Парткод:	4421 731 3000

Деталь:	KEY-HELP
Парткод:	4406306580

Деталь:	KEY-AT/CO-314
Парткод:	4421 731 4000

Деталь:	KEY-FL/CO-314
Парткод:	4421 731 5000

Деталь:	KEY-BLACK-31 4
Парткод:	4421 731 6000

Деталь:	COVER-LED-FC
Парткод:	440650501 0

Деталь:	COVER-LED-AT/CO
Парткод:	4406505020

Деталь:	MYLAR-SHIELD-R
Парткод:	4406505110

Деталь:	MYLAR-SHIELD-L
Парткод:	44065051 20

Деталь:	BRKT-CONP-31 0
Парткод:	44065051 00

Деталь:	K-PNL-TOUCH-330
Парткод:	4408860850

Деталь:	SPACER-PWA
Парткод:	4406306710

Деталь:	F-COV-CONP-314U
Парткод:	4421 7307000

Деталь:	F-COV-CONP-314E
Парткод:	4421 7308000

Деталь:	WH-DSP-LCD-300
Парткод:	4406382420

Деталь:	PWA-F-KEY-310
Парткод:	4406563040

Деталь:	PWA-F-PNL-310
Парткод:	4406563070

Деталь:	PWA-F-DSP-310
Парткод:	4406576090

Деталь:	COV-FRONT-UP
Парткод:	4406504440

Деталь:	BRKT-CONPANE-R
Парткод:	4406509070

Деталь:	COV-FT-PRTCON
Парткод:	440650451 0

Деталь:	BRKT-CONPANE-L
Парткод:	4406509080

Деталь:	LBL-COLOR-31 4
Парткод:	4421 731 8000

Деталь:	WS-2U
Парткод:	F0-00338000

Деталь:	HINGE-OPEN-UP
Парткод:	4406504420

Деталь:	SHEET-FT-PRTCON
Парткод:	4406504430

Деталь:	PLATE-CONP-PTR
Парткод:	4406504610

Деталь:	PLATE-MG-DF
Парткод:	4402822490

Деталь:	SEAL-DISP
Парткод:	4406306730

Деталь:	CFL-LCD-230
Парткод:	4402956850

Деталь:	LCD-TOUCH-1 54
Парткод:	4402322450

Деталь:	WH-CTRCNT-310
Парткод:	4406565580

Деталь:	GSKT-5-1 0-50
Парткод:	4421 7371 000

Деталь:	SHEET-BKT-CONP
Парткод:	4421 7940000

Деталь:	ASM-CNP-31 4-UC
Парткод:	4421 7301 000

Деталь:	ASM-CNP-31 4-EU
Парткод:	4421 7302000

Деталь:	S/PAN-M3X6-ZC
Парткод:	X0-00053000

Деталь:	S/TPP/BRZ-3X12-ZC
Парткод:	X0-01514000

Деталь:	SCREW-2006
Парткод:	4406306740

Деталь:	PTBR3006MSZN3A
Парткод:	4842040495

Деталь:	PTBR4008MSZN3A
Парткод:	4842040849

Деталь:	S/CTS-M4X1 0-ZU
Парткод:	X0-01 850000

Коды ошибок

C05

C06

C0A

C11

C12

C13

C14

C15

C16

C18

C27

C28

C29

C31

C33

C35

C38

C39

C3A

C3B

C3C

C3D

C3E

C3F

C41

C42

C43

C44

C46

C47

C48

C57

C5A

C5B

C5C

C72

C73

C74

C82

C94

C9A

C9B

C9D

C9E

CA1

CA2

CB1

CB2

CB3

CB4

CB5

CB6

CB7

CB8

CB9

CBA

CBB

CBC

CBD

CBE

CBF

CD1

CD2

CD3

CD4

CD5

CD6

CD7

CD9

CDA

CDB

CE1

CE2

CE3

CE4

CE5

CE6

CE9

CF1

E01

E02

E03

E11

E12

E13

E14

E15

E16

E19

E21

E22

E23

E24

E25

E26

E41

E42

E43

E45

E46

E50

E51

E52

E54

E71

E72

E73

E79

E9F

EA1

EA2

EA3

EA4

EA5

EA6

EA8

EA9

EAA

EAB

EAC

EAE

EB7

EC2

EC3

F07

F09

F10

F11

F12

F13

F51

Деталь:	K - HLDR - THRM - 314
Парткод:	4421 7825000

Деталь:	S/PAN/SWWS - M3X8 - ZC
Парткод:	X0-00072000

Деталь:	S/PAN/SWWP - M4X8 - ZC
Парткод:	X0-001 61 000

Деталь:	HTR - 115 - 550W - U
Парткод:	4421 9844000

Деталь:	HTR - 127 - 550W - U
Парткод:	4421 9846000

Деталь:	S/PAN/SWWS-M3X1 6-ZC
Парткод:	X0-0011 9000

Деталь:	S/PAN/SWWP - M3X30 - ZC
Парткод:	X0-001 37000

Деталь:	PWA - F - LGC - 314S
Парткод:	44220561 000

Деталь:	S/TPS/BID - 3X8 - ZB
Парткод:	X0-01 531 000

Error code:	C05
Description:	ADU motor rotation abnormal
Causes:	317 After the master compression motor on the first print drum side or second print drum side begins to apply a compression force, the compression detection activates and the other disposal box exceeds 90% capacity before the FG count exceeds the specified volume (Expected disposal box full).
Remedy:	Is the ADU motor rotating properly? N: 1. Check if the harness between the LGC board and the ADU drawer connector is open-circuited. 2. Check if the harness between the switching power supply and the ADU drawer connector is open-circuited. 3. Check if any of the connectors J101, J102 and J104 on the LGC board is disconnected. 4. Reduce the mechanical load on the motor by adjusting the drive system. Remove foreign matter if any. 5. Replace the LGC board. Y: Are the pins B2 and B4 of the connector J104 on the LGC board always at the level "L"? N: 1. Check if the connector J104 on the LGC board is disconnected. 2. Check if any conductor pattern on the LGC board is open- or short-circuited. 3. Check if any harness is open-circuited or any connector pin is disconnected. 4. Replace the LGC board. Y: 1. Check if any conductor pattern on the LGC board is open- or short-circuited. 2. Replace the LGC board.

Деталь:	K-TERM-UTNR-UP
Парткод:	4406532950

Деталь:	SEAL-UTNR-UP-U
Парткод:	44065331 20

Деталь:	MYLAR-UTNR-UP
Парткод:	44065331 30

Деталь:	SEAL-UTNR-UP-L
Парткод:	4406533480

Error code:	C06
Description:	Feed motor rotation abnormal
Causes:	859 No paper in Tray No.1
Remedy:	Is the paper feed motor rotating properly? N: 1. Check if the connector J41 of the paper feed motor is disconnected. 2. Check if the connector J109 on the LGC board is disconnected. 3. Check if the connector J703 of the switching power supply is disconnected. 4. Check if the harness between the LGC board and the paper feed motor is open-circuited. 5. Check if the harness between the switching power supply and the paper feed motor is open-circuited. 6. Check if any harness is open-circuited or any connector pin is disconnected. 7. Rotate the motor manually, clockwise as seen from its back, and if the motor load is abnormal, remove any foreign matter from the drive unit. 8. Replace the paper feed motor. 9. Replace the LGC board. Y: Are the pins A6 and A10 of the connector J109 on the LGC board always at the level "L"? N: 1. Check if the connector J41 of the paper feed motor is disconnected. 2. Check if the connector J109 on the LGC board is disconnected. 3. Check if any conductor pattern on the LGC board is open- or short-circuited. 4. Check if any harness is open-circuited or any connector pin is disconnected. 5. Replace the LGC board. 6. Replace the paper feed motor. Y: 1. Check if any conductor pattern on the LGC board is open- or short-circuited. 2. Replace the LGC board. 3. Replace the paper feed motor.

Error code:	C0A
Description:	Developer motor rotation abnormal
Remedy:	Is the developer motor rotating properly? N: 1. Check if the connector J41 or J43 of the developer motor is disconnected. 2. Check if the connector J109 on the LGC board is disconnected. 3. Check if the connector J703 of the switching power supply is disconnected. 4. Check if the harness between the LGC board and the developer motor is open-circuited. 5. Check if the harness between the switching power supply and the developer motor is open-circuited. 6. Check if any harness is open-circuited or any connector pin is disconnected. 7. Rotate the motor manually, counterclockwise as seen from its back, and if the motor load is abnormal, remove any foreign matter from the drive unit. (Do not try to rotate the motor clockwise as seen from its back.) 8. Replace the developer motor. 9. Replace the LGC board. Y: Are the pins B12 and B16 of the connector J109 on the LGC board always at the level "L"? N: 1. Check if the connector J41 of the developer motor is disconnected. 2. Check if the connector J109 on the LGC board is disconnected. 3. Check if any conductor pattern on the LGC board is open- or short-circuited. 4. Check if any harness is open-circuited or any connector pin is disconnected. 5. Replace the LGC board. 6. Replace the developer motor. Y: 1. Check if any conductor pattern on the LGC board is open- or short-circuited. 2. Replace the LGC board. 3. Replace the developer motor.

Error code:	C11
Description:	ADU paper side guide operation abnormal
Remedy:	Is the ADU pushed in securely to the copier? N: Push in the ADU securely to the copier. Y: Has the timing belt for driving the paper side guide come off? Y: Put the belt on properly. N: Is the connector J104 on the LGC board disconnected? Is the harness between the LGC board and the ADU drawer connector open-circuited? Y: Reconnect the connector. Replace the harness. N: 1. Replace the LGC board. 2. Replace the ADU.

Error code:	C12
Description:	ADU paper end guide operation abnormal
Remedy:	Is the ADU pushed in securely to the copier? N: Push in the ADU securely to the copier. Y: Has the timing belt for driving the paper end guide come off? N: Is the connector J104 on the LGC board disconnected? Is the harness between the LGC board and the ADU drawer connector open-circuited? Y: Reconnect the connector. Replace the harness. N: 1. Replace the LGC board. 2. Replace the ADU.

Error code:	C13
Description:	1st cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C14
Description:	2nd cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C15
Description:	3rd cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C16
Description:	4th cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C18
Description:	LCF tray operation abnormal
Remedy:	Is the harness between the LGC board and the LCF unit open-circuited? Is the relay connector of the harness between the LGC board and the LCF unit or the connector J105 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: Are the switches and sensors in the LCF unit working properly? Y: 1. Replace the LCF tray motor. 2. Replace the LGC board. N: 1. Replace the sensors and switches. 2. Replace the LCF drive PC board or the LCF tray-down switch PC board. 3. Replace the LGC board.

Error code:	C27
Description:	Carriage home position sensor not turning OFF within a fixed time
Causes:	• If the Master sensor does not find master on the Drum when the Drum is at 79° during the printing movement.
Remedy:	Are the carriages stuck at a point other than the home position? Y: Check the SCM and SDV boards for any abnormal circuit. N: 1. Check if any connector pin is disconnected, or any harness is open- or short-circuited. 2. Check the scan motor drive pulley if its screws are loose. 3. Check if any conductor pattern on the SDV board is open- or short-circuited. 4. Check if any conductor pattern on the SCM board is open- or short-circuited. 5. Replace the SDV board. 6. Replace the SCM board.