Toshiba e-Studio 2320c
Рейтинг
Модули
BYPASS-FEEDER-2-ASY
LASER-OPTICAL-UNIT
OPTICAL-FRAME-ASY
ADU-ASY-2
ADU-ASY-1
BELT-CLEAN-UNIT-ASY
CLN-DRUM-ASY
DOWNLOAD JIGS
FEEDER-1-ASY
TRANSPORT-BELT-UNIT-1
CRG-2-ASY
COV_STAY-PCB-ASY
REAR-FRAME-ASY-2
POWER-SUPPLY-ASY
FRONT-FRAME-ASY
SUPPLIES
DEVELOPER-ASY
FEEDER-2-ASY
DRUM-DRIVE-ASY
TRANSPORT-BELT-UNIT-2
CASE-PCB-ASY
MAIN-CHARGER-ASY
TRU-UNIT-2
BYPASS-ASY
COV&GUIDE-FEED-ASY
TONER-1-ASY
COVER-2-ASY
FUSER&EXIT-DRIVE-ASY
BASE-FRAME-ASY
TRU-UNIT-1
SHUTTER-ASY
REAR-FRAME-ASY-1
FUSER-3-ASY
REGIST&TR1-DRIVE-ASY
REPLACE UNIT
BYPASS-FEEDER-1-ASY
JIGS & GREASE
TRANSPORT-BELT-UNIT-3
LIFT-TRU&SNR-POS-ASY
CRG-1-ASY
COVER-1-ASY
DRAWER-ASY
FUSER SATY&GUIDE EXIT-ASY
FUSER-1-ASY
INNER-COVER-ASY
CONTROL-PANEL-ASY
PLATEN-ASY
DEV_TBU-DRIVE-ASY
ALIGNING-ASY
TRANSPORT-BELT-UNIT-4
PM-KIT
TONER-2-ASY
OPTICAL-DRIVE-ASY
FUSER-2-ASY
EPU-SUB-ASY
Детали FEEDER-2-ASY
| Деталь: | ASYS-FRM-BYPASS-380 |
| Парткод: | 6LE21223000 |
| Деталь: | SPL-IDLR-TR-BYPS-N |
| Парткод: | 6LE21254000 |
| Деталь: | SHAFT-IDLR-TR-BYPS |
| Парткод: | 6LA28966000 |
| Деталь: | IDLER-TR-BYPASS-K |
| Парткод: | 6LE40416000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | ACTUATOR-BYP |
| Парткод: | 6LE40422000 |
| Деталь: | SPG-T-SNSR-LOW-T |
| Парткод: | 6LA28960000 |
| Деталь: | BRKT-ACT-BYP |
| Парткод: | 6LA28952000 |
| Деталь: | ASYS-BRKT-FRM-BYPS-FRT |
| Парткод: | 6LE21225000 |
| Деталь: | GUIDE-BYPASS-U |
| Парткод: | 6LE40440000 |
| Деталь: | SOL-SFB-340 |
| Парткод: | 6LA15259000 |
| Деталь: | LEVER-PICK |
| Парткод: | 6LA28767000 |
| Деталь: | STUD-LVR-PIC-BP |
| Парткод: | 6LE40435000 |
| Деталь: | SPG-E-6R5XR7X28R5L |
| Парткод: | 6LA28769000 |
| Деталь: | STAY-BYPASS-U |
| Парткод: | 6LA28827000 |
| Деталь: | ASYS-COVER-BYPASS-U |
| Парткод: | 6LE40442000 |
| Деталь: | ACTR-EMP-SW-BYP |
| Парткод: | 6LA28768000 |
| Деталь: | ASYS-BRKT-STOPPER |
| Парткод: | 6LA28823000 |
| Деталь: | STPR-BYP-F-350 |
| Парткод: | 6LA28821000 |
| Деталь: | ARM-STOPPER |
| Парткод: | 4401965270 |
| Деталь: | LEVER-STOPPER-F |
| Парткод: | 4401965250 |
| Деталь: | STPR-BYP-R-350 |
| Парткод: | 6LA28822000 |
| Деталь: | LEVER-STOPPER-R |
| Парткод: | 4401965260 |
| Деталь: | PLATE-ARM-PICK |
| Парткод: | 6LA28819000 |
| Деталь: | BLT-SY-138-2GT-2.8 |
| Парткод: | 6LA28835000 |
| Деталь: | K-ROLL-PICK-BYP |
| Парткод: | 44218398000 |
| Деталь: | SFT-ROL-PIC-BYP-350 |
| Парткод: | 6LE40436000 |
| Деталь: | SHAFT-ROL-FEED-BYPS |
| Парткод: | 6LA28807000 |
| Деталь: | GEAR-06S-027-06 |
| Парткод: | 6LA28811000 |
| Деталь: | CLUTCH-6-L |
| Парткод: | 6LE69842000 |
| Деталь: | ARM-PICK-350 |
| Парткод: | 6LA28756000 |
| Деталь: | WEIGHT-PICK-BYP-LOW |
| Парткод: | 6LA28832000 |
| Деталь: | WEIGHT-PICK-BYP-UP |
| Парткод: | 6LA28834000 |
| Деталь: | SPL-ROL-FEED-BYP |
| Парткод: | 6LA28817000 |
| Деталь: | CUSHION-PAD |
| Парткод: | 6LA28758000 |
| Деталь: | PLY/T-2GT020-06 |
| Парткод: | 4401966400 |
| Деталь: | K-RLR-FEED-SFB |
| Парткод: | 44218389000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | CPG-DRVN-BYP-350 |
| Парткод: | 6LA28812000 |
| Деталь: | ROLLER-TR-BYPASS-18.5 |
| Парткод: | 6LE40425000 |
| Деталь: | STUD-G032-BYPS |
| Парткод: | 6LE40439000 |
| Деталь: | GEAR-06S-032-06 |
| Парткод: | 44201789000 |
| Деталь: | HRNS-SFB-380 |
| Парткод: | 6LE29398000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | SCREW-WEIGHT-36 |
| Парткод: | 6LE40407000 |
| Деталь: | WEIGHT-PICK-BYP-T |
| Парткод: | 6LE40412000 |
| Деталь: | WEIGHT-PICK-BYP-MID |
| Парткод: | 6LA28833000 |
| Деталь: | HRNS-SFB-PIS-360 |
| Парткод: | 6LA71421000 |
| Деталь: | SPL-IDLR-TR-BYP-R |
| Парткод: | 6LE21252000 |
| Деталь: | P/PRL/AH7-2X8-SS |
| Парткод: | X0-00979000 |
| Деталь: | S/CTS-M3X8-NI |
| Парткод: | X0-02011000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | DUCT-LSU-R-D-LWR |
| Парткод: | 6LE22625000 |
| Деталь: | DUCT-LSU-R-D-UPR |
| Парткод: | 6LE22626000 |
| Деталь: | GEAR-08S21-TRU-S |
| Парткод: | 6LE29011000 |
| Деталь: | STOP-RING-6-4 |
| Парткод: | 4408358930 |
| Деталь: | HRNS-TRUPS-380 |
| Парткод: | 6LE29384000 |
| Деталь: | PLT-PUSH-TRU |
| Парткод: | 6LE29013000 |
| Деталь: | PUSHER-TRU |
| Парткод: | 6LE29009000 |
| Деталь: | SCREW-SCAN-DF |
| Парткод: | 6LA67469000 |
| Деталь: | ASYS-DUCT-LSU-LWR |
| Парткод: | 6LE22646000 |
| Деталь: | DUCT-LSU-FN-UPR |
| Парткод: | 6LE22645000 |
| Деталь: | ASYS-CLNR-GLASS |
| Парткод: | 6LE26465000 |
| Деталь: | ASYS-FAN-LSU-380 |
| Парткод: | 6LE22631000 |
| Деталь: | HLDR-MID-ROLLER |
| Парткод: | 6LE24251000 |
| Деталь: | SEAL-DUCT-LSU |
| Парткод: | 6LE26505000 |
| Деталь: | ASYB-CLNR-LSU |
| Парткод: | 6LE26482000 |
| Деталь: | COVER-SPG-CAM-F-380 |
| Парткод: | 6LE24342000 |
| Деталь: | COVER-SPG-CAM-R-380 |
| Парткод: | 6LE24343000 |
| Деталь: | SPG-DETENT-TRU |
| Парткод: | 6LE29015000 |
| Деталь: | SEAL-DUCT-LSU-F-A |
| Парткод: | 6LE26535000 |
| Деталь: | SEAL-DUCT-LSU-F-B |
| Парткод: | 6LE26536000 |
| Деталь: | LASER-UNIT-450 |
| Парткод: | 6LH36823000 |
| Деталь: | LASER-UNIT-453 |
| Парткод: | 6LH36823100 |
| Деталь: | OTLV6-500B |
| Парткод: | F0-01560000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | EDS-1717U |
| Парткод: | F0-00047000 |
| Деталь: | RLWS-1TV0 |
| Парткод: | F0-00367000 |
| Деталь: | LES-1010 |
| Парткод: | F0-00542000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | S/PAN/SWWP-M4X16-N1 |
| Парткод: | X0-00198000 |
| Деталь: | P/PRL/AH7-2X8-SS |
| Парткод: | X0-00979000 |
| Деталь: | EDS-0607M |
| Парткод: | F0-00671000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | LID-DOWNLOAD |
| Парткод: | 6LA39881000 |
| Деталь: | COVER-FOOT-SCAN-380 |
| Парткод: | 6LE27445000 |
| Деталь: | HRNS-SCN-SYS-450 |
| Парткод: | 6LH39754000 |
| Деталь: | HRNS-SCN-SNSR-450 |
| Парткод: | 6LH39892000 |
| Деталь: | HRNS-SCN-PS-450 |
| Парткод: | 6LH39750000 |
| Деталь: | COVER-KEY |
| Парткод: | 6LE27449000 |
| Деталь: | LENS-UNIT-450 |
| Парткод: | 6LH37860000 |
| Деталь: | SNSR-PS-TY1CH56 |
| Парткод: | 6LE09478000 |
| Деталь: | CUSH-STAY-TP-LFT |
| Парткод: | 6LA39926000 |
| Деталь: | HOLDER-USB-45X |
| Парткод: | 6LH33222000 |
| Деталь: | CABLE-USB-450 |
| Парткод: | 6LH39790000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | COVER-HRNS-SLG |
| Парткод: | 6LA39453000 |
| Деталь: | BRKT-FAN-RER-380 |
| Парткод: | 6LE27450000 |
| Деталь: | MYLAR-BASE-SCAN |
| Парткод: | 6LA39908000 |
| Деталь: | STAY-TP-RGT-SCAN |
| Парткод: | 6LA39866000 |
| Деталь: | ASYS-BRKT-COV-REL-LR |
| Парткод: | 6LE27446000 |
| Деталь: | S/TPS/BID-3X6-ZU3 |
| Парткод: | X0-02069000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | AJ8W200WWF |
| Парткод: | E0-08497000 |
| Деталь: | DUCT-SCAN-RER |
| Парткод: | 6LA39673000 |
| Деталь: | FAND-6015-39X |
| Парткод: | 6LE09967000 |
| Деталь: | S/TPS/FHEXM-4X8-ZU3 |
| Парткод: | X0-02243000 |
| Деталь: | CUSH-DUCT-SCAN-RER |
| Парткод: | 6LA39675000 |
| Деталь: | ASY-SLG-430S |
| Парткод: | 6LH09328000 |
| Деталь: | LOCK-CRG-450 |
| Парткод: | 6LH37829000 |
| Деталь: | COVER-SNSR-LIFT |
| Парткод: | 6LA29902000 |
| Деталь: | EDS-2323U |
| Парткод: | F0-00034000 |
| Деталь: | S/PAN/SWWP-M3X8-NI |
| Парткод: | X0-00077000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | RLWC-6SV0 |
| Парткод: | F0-01629000 |
| Деталь: | WWS-2U |
| Парткод: | F0-01179000 |
| Деталь: | LES-1010 |
| Парткод: | F0-00542000 |
| Деталь: | RLWS3TV0 |
| Парткод: | F0-00036000 |
| Деталь: | S/TPP/PAN-3X20-NI |
| Парткод: | X0-02344000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | LWS-0711Z |
| Парткод: | F0-00736000 |
| Деталь: | SNSR-PS-TW06 |
| Парткод: | 6LE48550000 |
| Деталь: | BRKT-D_H-LENS |
| Парткод: | 6LA39898000 |
| Деталь: | ASY-D-H-SCAN-L-E-371 |
| Парткод: | 6LA86520000 |
| Деталь: | ASY-D_H-SCAN-L-U-371 |
| Парткод: | 6LA86519000 |
| Деталь: | ASY-D-H-SCAN-R-E-371 |
| Парткод: | 6LA86523000 |
| Деталь: | ASY-D_H-SCAN-R-U-371 |
| Парткод: | 6LA86522000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | GUIDE-P-U-380 |
| Парткод: | 6LE21023000 |
| Деталь: | SNSR-FED-390 |
| Парткод: | 6LE09239000 |
| Деталь: | COVER-ADU-UND-380D |
| Парткод: | 6LE21004000 |
| Деталь: | SCREW-CH-M |
| Парткод: | 6LE06406000 |
| Деталь: | CASE-ADU-380 |
| Парткод: | 6LE21013000 |
| Деталь: | SP-CS3A-B2BA |
| Парткод: | 4402859600 |
| Деталь: | COVER-IN-F-380 |
| Парткод: | 6LE21021000 |
| Деталь: | LBL-O-PLACE-COV |
| Парткод: | 6LA28607000 |
| Деталь: | LBL-INST-ADU |
| Парткод: | 6LE25956000 |
| Деталь: | LBL-HOT-410 |
| Парткод: | 6LE45619000 |
| Деталь: | COVER-GUIDE-RTN |
| Парткод: | 6LH34302000 |
| Деталь: | GUIDE-RTN-U-FC |
| Парткод: | 6LH36325000 |
| Деталь: | ASYS-COVER-SHLD-45X |
| Парткод: | 6LH34301000 |
| Деталь: | COVER-BRKT-ADU-380 |
| Парткод: | 6LE21019000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | T18R |
| Парткод: | F0-01012000 |
| Деталь: | SG-130 |
| Парткод: | F0-00260000 |
| Деталь: | S/TPS/FHEXM-3X8-ZU3 |
| Парткод: | X0-02239000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | COV-IN-R-380 |
| Парткод: | 6LE21008000 |
| Деталь: | SFT-TR-L-20 |
| Парткод: | 6LE40307000 |
| Деталь: | ROL-TR-CLT-ADU-DK |
| Парткод: | 6LE40306000 |
| Деталь: | GUIDE-P-IN-DK-B1 |
| Парткод: | 6LE40309100 |
| Деталь: | GUIDE-PAPER-L32D |
| Парткод: | 6LE40313000 |
| Деталь: | SCREW-CASET |
| Парткод: | 6LA28608000 |
| Деталь: | ROLL-TR-U-16 |
| Парткод: | 6LE40304000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | PLY/T-2GT020-6F |
| Парткод: | 41317051000 |
| Деталь: | P/PRL/AH7-2X8-SS |
| Парткод: | X0-00979000 |
| Деталь: | BLT/T-286-2GT-5 |
| Парткод: | 6LE40312000 |
| Деталь: | PLY/T-2GT016-6F |
| Парткод: | 6LE40308000 |
| Деталь: | BLT/T-258-2GT-5 |
| Парткод: | 6LA78706000 |
| Деталь: | CLUTCH-G28-06D-35E |
| Парткод: | 6LA78512000 |
| Деталь: | ASYS-BKT-MOT-ADU-380 |
| Парткод: | 6LE21015000 |
| Деталь: | AYSY-MOTR-S-ADU-371 |
| Парткод: | 6LA78482000 |
| Деталь: | GEAR-10S28-P2GT20-6 |
| Парткод: | 6LA78452000 |
| Деталь: | GEAR-10S15-PS2M39-6 |
| Парткод: | 6LA78772000 |
| Деталь: | GEAR-10S28-06 |
| Парткод: | 6LA78496000 |
| Деталь: | BLT-SY-S2M-120-4 |
| Парткод: | 6LA78447000 |
| Деталь: | LEVER-LATCH-F |
| Парткод: | 41316054000 |
| Деталь: | LEVER-LATCH-R32 |
| Парткод: | 44203255000 |
| Деталь: | SHAFT-OPEN-350 |
| Парткод: | 6LA28625000 |
| Деталь: | LEVER-OPEN-ADU |
| Парткод: | 6LE40317000 |
| Деталь: | SPE-068-070-241 |
| Парткод: | 41316064000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | KGLS-24RTV0 |
| Парткод: | F0-00221000 |
| Деталь: | PWA-F-ADU-410 |
| Парткод: | 6LE47128000 |
| Деталь: | HRNS-ADU-FED-L-360 |
| Парткод: | 6LA71342000 |
| Деталь: | HRNS-ADU-CVSW-371 |
| Парткод: | 6LA89451000 |
| Деталь: | HRNS-ADU-MOT-371 |
| Парткод: | 6LA89448000 |
| Деталь: | HRNS-ADU-450 |
| Парткод: | 6LH39915000 |
| Деталь: | HRNS-ADU-FED-U-410 |
| Парткод: | 6LE48050000 |
| Деталь: | SPCR-SPL-GUIDE-380 |
| Парткод: | 6LE21012000 |
| Деталь: | SPL-GUIDE-IN-380 |
| Парткод: | 6LE21017000 |
| Деталь: | ROLL-TRANS-C-371 |
| Парткод: | 6LA78672000 |
| Деталь: | SPL-ADU-320 |
| Парткод: | 44203240000 |
| Деталь: | ROLL-TRANS-IDLE-371 |
| Парткод: | 6LA78742000 |
| Деталь: | SPR-IDLE |
| Парткод: | 41316103000 |
| Деталь: | SPR-IDLE-U |
| Парткод: | 6LE40310000 |
| Деталь: | PLATE-PUSH-INT |
| Парткод: | 6LE21007000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/FHEXM-M3X8-NI |
| Парткод: | X0-02231000 |
| Деталь: | S/TPS/FHEXM-3X8-ZU3 |
| Парткод: | X0-02239000 |
| Деталь: | T18R |
| Парткод: | F0-01012000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | MSB-1207 |
| Парткод: | F0-01250000 |
| Деталь: | FRAME-CLN-TBU-F380 |
| Парткод: | 6LE28373000 |
| Деталь: | SHEET-AUGER-TBU |
| Парткод: | 6LE28329000 |
| Деталь: | PLATE-CLN-TBU |
| Парткод: | 6LE28434000 |
| Деталь: | BL-FC35TR |
| Парткод: | 6LE94755000 |
| Деталь: | AUGER-CLN-TBU |
| Парткод: | 6LE28234000 |
| Деталь: | GEAR-CLN-TBU |
| Парткод: | 6LE28272000 |
| Деталь: | SHUTTER-EXIT-CLN-TBU |
| Парткод: | 6LE28331000 |
| Деталь: | SEAL-BLADE-CLN-TBU-F |
| Парткод: | 6LE28321000 |
| Деталь: | LBL-HANDLE-CLN-TBU |
| Парткод: | 6LE28430000 |
| Деталь: | BUSH-0418-05F-M |
| Парткод: | 6LE28376000 |
| Деталь: | SEAL-BLADE-CLN-TBU-R |
| Парткод: | 6LE28322000 |
| Деталь: | SEAL-SIDE-BLADE-TBU |
| Парткод: | 6LE28323000 |
| Деталь: | BUSH-4-CLN-TBU-F |
| Парткод: | 6LE42524000 |
| Деталь: | SPG-C-SHUTTER-EXIT |
| Парткод: | 6LE28333000 |
| Деталь: | SHEET-REC-TBU |
| Парткод: | 6LE28330000 |
| Деталь: | RAIL-CLN-TBU-U |
| Парткод: | 6LE28312000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | S/TPP/PAN-3X6-NI |
| Парткод: | X0-00595000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | CASE-CLNR-DRUM-380 |
| Парткод: | 6LE23236000 |
| Деталь: | SEAL-BLADE-BCK |
| Парткод: | 6LE23117000 |
| Деталь: | SHEET-CASE-CLNR-AUGER |
| Парткод: | 6LE23114000 |
| Деталь: | SEAL-WASTE-TNR |
| Парткод: | 6LE23131000 |
| Деталь: | GEAR-8S23-4-AUGER |
| Парткод: | 6LE23107000 |
| Деталь: | BUSH-4-CLN-TBU-F |
| Парткод: | 6LE42524000 |
| Деталь: | AUGER-CLNR-DRUM-380 |
| Парткод: | 6LE23106000 |
| Деталь: | ASYB-WASTE-TNR-DUCT |
| Парткод: | 6LE23613000 |
| Деталь: | CAM-WASTE-DUCT |
| Парткод: | 6LE23181000 |
| Деталь: | CLNR-WASTE-DUCT |
| Парткод: | 6LE23180000 |
| Деталь: | ASYS-DUCT-WASTE-TNR-F |
| Парткод: | 6LE23612000 |
| Деталь: | RRG-2R65X7XR5-PS |
| Парткод: | 6LE23123000 |
| Деталь: | SPG-C-BIAS-BLADE-DRUM |
| Парткод: | 6LE23112000 |
| Деталь: | HLDR-BLADE-DRUM-380 |
| Парткод: | 6LE23109000 |
| Деталь: | SPG-F-BIAS-BLADE-DRUM |
| Парткод: | 6LE23237000 |
| Деталь: | BL-FC28D |
| Парткод: | 6LE98146000 |
| Деталь: | SPG-E-3R9XR4X13-BLADE |
| Парткод: | 6LE23110000 |
| Деталь: | SEAL-BLADE-SIDE-F |
| Парткод: | 6LE23115000 |
| Деталь: | SEAL-BLADE-SIDE-R |
| Парткод: | 6LE23116000 |
| Деталь: | BLADE-REC-DRUM-380-C |
| Парткод: | 6LE23210000 |
| Деталь: | SEAL-DRUM-F |
| Парткод: | 6LE23228000 |
| Деталь: | SEAL-DRUM-F-S |
| Парткод: | 6LE23229000 |
| Деталь: | SLEEVE-DRUM-SHAFT |
| Парткод: | 6LE23220000 |
| Деталь: | RTNR-DRUM-SHAFT |
| Парткод: | 6LE23121000 |
| Деталь: | ASYB-SHAFT-DRUM |
| Парткод: | 6LE23625000 |
| Деталь: | TAPE-CONDUCT |
| Парткод: | 6LE23235000 |
| Деталь: | S/BID-M3X4-NI |
| Парткод: | X0-00426000 |
| Деталь: | 608ZZM2MTLY13 |
| Парткод: | F0-01370000 |
| Деталь: | K-PWA-DLM-320 |
| Парткод: | 44205829000 |
| Деталь: | PWA-DWNLD-350-JIG2 |
| Парткод: | 6LA41995000 |
| Деталь: | PWA-DL-ADP-350-1881 |
| Парткод: | 6LA41996000 |
| Деталь: | PWA-DL-ADP-350-1931 |
| Парткод: | 6LA41997000 |
| Деталь: | K-PWA-DLS-320 |
| Парткод: | 44205828000 |
| Деталь: | M27C4001-10F1 |
| Парткод: | C0-04530000 |
| Деталь: | M27C160-100F1 |
| Парткод: | C0-05769000 |
| Деталь: | BRKT-ROL-SEP |
| Парткод: | 6LA47898000 |
| Деталь: | ASYS-GUIDE-P-SEP |
| Парткод: | 6LA66947000 |
| Деталь: | hldr-sep-rol-dm |
| Парткод: | 44201805000 |
| Деталь: | LEVER-RLR-PICK |
| Парткод: | 6LA47910000 |
| Деталь: | K-ROLL-SPT |
| Парткод: | 41304047100 |
| Деталь: | ARBOR-SPT-F |
| Парткод: | 4401964360 |
| Деталь: | ARBOR-SPT-R |
| Парткод: | 4401964270 |
| Деталь: | SFT-SEP-AT |
| Парткод: | 41304506000 |
| Деталь: | SPR-1.0-15.60RF |
| Парткод: | 44201817000 |
| Деталь: | SPC055-045-01525 |
| Парткод: | 6LA47909000 |
| Деталь: | cov-spe/arbor |
| Парткод: | 44201773000 |
| Деталь: | CHIP-HLDR-SEP |
| Парткод: | 41319491000 |
| Деталь: | GUIDE-P-FEED |
| Парткод: | 6LA47908000 |
| Деталь: | ACTR-EMPTY-PPR |
| Парткод: | 41306012000 |
| Деталь: | ARM-FEED-UNIT |
| Парткод: | 41318603000 |
| Деталь: | SFT-DRV-PICK |
| Парткод: | 41318604000 |
| Деталь: | ARM-RLR-PICK-380 |
| Парткод: | 6LE24295000 |
| Деталь: | PLY/T-PICK-20 |
| Парткод: | 41306002000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | ROLLER-PICK-AT |
| Парткод: | 41306719000 |
| Деталь: | CLUTCH-6-L |
| Парткод: | 6LE69842000 |
| Деталь: | PLY-20-2M |
| Парткод: | 4402231780 |
| Деталь: | SHAFT-ROL-FEED-380 |
| Парткод: | 6LE24306000 |
| Деталь: | K-ROLL-FEED |
| Парткод: | 6LE69833000 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | PLY/T-20-ROL-2G |
| Парткод: | 41306274000 |
| Деталь: | lev-rol-sep-dm |
| Парткод: | 44201810000 |
| Деталь: | ASYS-BRKT-CLT-380 |
| Парткод: | 6LE24258000 |
| Деталь: | CLUTCH-G28-06D-30AK |
| Парткод: | 6LE27035000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | BLT/T-194-2GT-2 |
| Парткод: | 41306504000 |
| Деталь: | BLT/T-124-2GT-2 |
| Парткод: | 41306502000 |
| Деталь: | T18R |
| Парткод: | F0-01012000 |
| Деталь: | SPR-LVR-PICK |
| Парткод: | 41305501000 |
| Деталь: | HRNS-PFP-FED-380 |
| Парткод: | 6LE29399000 |
| Деталь: | ASYS-BRKT-FEED-UNIT |
| Парткод: | 6LA47892000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | P/PRL/AH7-2X8-SS |
| Парткод: | X0-00979000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | 54702-1219 |
| Парткод: | E0-08732000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | MSB-1207 |
| Парткод: | F0-01250000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | EDS-0607M |
| Парткод: | F0-00671000 |
| Деталь: | S/TPS/FHEXM-3X8-ZU3 |
| Парткод: | X0-02239000 |
| Деталь: | SPG-TBU-TNS-GND |
| Парткод: | 6LH38610000 |
| Деталь: | ARM-TENSION-MOLD |
| Парткод: | 6LE28204000 |
| Деталь: | HLDR-BRG-F-450 |
| Парткод: | 6LH38601000 |
| Деталь: | HLDR-BRG-R-450 |
| Парткод: | 6LH38600000 |
| Деталь: | HOOK-CLN-TBU-F |
| Парткод: | 6LE28288000 |
| Деталь: | HOOK-CLN-TBU-R |
| Парткод: | 6LE28289000 |
| Деталь: | ASYS-FRAME-HINGE |
| Парткод: | 6LE28222000 |
| Деталь: | HLDR-PAD-CLN-TR2-N |
| Парткод: | 6LH38623000 |
| Деталь: | MYLAR-CLN-TR2-WP-450 |
| Парткод: | 6LH38622000 |
| Деталь: | ASYS-PLATE-CLN-F |
| Парткод: | 6LE28229000 |
| Деталь: | ASYS-PLATE-CLN-R |
| Парткод: | 6LE28230000 |
| Деталь: | BASE-TERMINAL-TBU |
| Парткод: | 6LE28236000 |
| Деталь: | LBL-HANDL-TBU |
| Парткод: | 6LE28431000 |
| Деталь: | BUSH-0604-GCB |
| Парткод: | 4408309990 |
| Деталь: | LVR-LIFT-TR1-R |
| Парткод: | 6LE28442000 |
| Деталь: | HOLDER-WH |
| Парткод: | 4407685930 |
| Деталь: | BUSH-TR2-TBU |
| Парткод: | 6LE28475000 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | ASYS-FRAME-TBU-HINGE-R |
| Парткод: | 6LE28432000 |
| Деталь: | LVR-TBU-F380 |
| Парткод: | 6LE28487000 |
| Деталь: | CAM-LIFT-CLN-TBU |
| Парткод: | 6LE28245000 |
| Деталь: | CAM-LIFT-TNS |
| Парткод: | 6LE28252000 |
| Деталь: | CAM-SIDE-PLATE-CLN |
| Парткод: | 6LE28253000 |
| Деталь: | COVER-TERMINAL-TBU |
| Парткод: | 6LE28258000 |
| Деталь: | HRNS-TBU-450 |
| Парткод: | 6LH40050000 |
| Деталь: | HRNS-TBUHV-C-380 |
| Парткод: | 6LE29418000 |
| Деталь: | HRNS-TBUHV-K-380 |
| Парткод: | 6LE29419000 |
| Деталь: | HRNS-TBUHV-M-380 |
| Парткод: | 6LE29417000 |
| Деталь: | HRNS-TBUHV-Y-380 |
| Парткод: | 6LE29416000 |
| Деталь: | GEAR-DRV-TBU-M04 |
| Парткод: | 6LE22160000 |
| Деталь: | PLATE-TBU-CL |
| Парткод: | 6LE28481000 |
| Деталь: | GUIDE-STUD-CLN-TBU |
| Парткод: | 6LE28276000 |
| Деталь: | GUIDE-WH-TR |
| Парткод: | 6LE28277000 |
| Деталь: | PLATE-TERM-TBU-TR2 |
| Парткод: | 6LE28307000 |
| Деталь: | PLATE-TERMINAL-TBU |
| Парткод: | 6LE28308000 |
| Деталь: | SHAFT-CAM-LVR-CLN |
| Парткод: | 6LE28325000 |
| Деталь: | SPG-E-TNS-9N |
| Парткод: | 6LE28531000 |
| Деталь: | SPG-E-CLN-TBU |
| Парткод: | 6LE28478000 |
| Деталь: | SPG-F-TR2 |
| Парткод: | 6LE28343000 |
| Деталь: | LVR-LIFT-TR1 |
| Парткод: | 6LE28301000 |
| Деталь: | MYLAR-TBU-F380-F-1 |
| Парткод: | 6LE28414000 |
| Деталь: | MYLAR-TBU-F380-F-2 |
| Парткод: | 6LE28415000 |
| Деталь: | MYLAR-TBU-F380-F-3 |
| Парткод: | 6LE28416000 |
| Деталь: | MYLAR-TBU-F380-R-1 |
| Парткод: | 6LE28418000 |
| Деталь: | MYLAR-TBU-F380-R-2 |
| Парткод: | 6LE28417000 |
| Деталь: | SPG-F-HOOK-STOP |
| Парткод: | 6LE28486000 |
| Деталь: | DDL-1680HH |
| Парткод: | F0-01159000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | LNR-1680HHRP0P15LY13 |
| Парткод: | F0-01390000 |
| Деталь: | S/TPP/PAN-3X8-NI |
| Парткод: | X0-00602000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | DDLF-1260ZZRPOP25LY349 |
| Парткод: | F0-01707000 |
| Деталь: | S/TPS/FHEXM-3X8-ZU3 |
| Парткод: | X0-02239000 |
| Деталь: | S/PAN/SWWP-M3X8-NI |
| Парткод: | X0-00077000 |
| Деталь: | FOOT-CRG-410 |
| Парткод: | 6LE46323000 |
| Деталь: | GUIDE-WH-CRG2 |
| Парткод: | 44202692000 |
| Деталь: | S/TPS/BID-3X6-ZU3 |
| Парткод: | X0-02069000 |
| Деталь: | CARRIGE-2-450 |
| Парткод: | 6LH37859000 |
| Деталь: | COVER-DL-380 |
| Парткод: | 6LE22834000 |
| Деталь: | COVER-PIF-380 |
| Парткод: | 6LE22835000 |
| Деталь: | RLWC-6SV0 |
| Парткод: | F0-01629000 |
| Деталь: | S/TPS/FHEXM-3X8-ZU3 |
| Парткод: | X0-02239000 |
| Деталь: | STUD-ADU-380 |
| Парткод: | 6LE21005000 |
| Деталь: | EDS-1717U |
| Парткод: | F0-00047000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | LWS-1316Z |
| Парткод: | F0-01245000 |
| Деталь: | MSB-1207 |
| Парткод: | F0-01250000 |
| Деталь: | HL-18-0 |
| Парткод: | F0-00505000 |
| Деталь: | PLATE-COVER-FAX |
| Парткод: | 6LE22883000 |
| Деталь: | RFC-16V0 |
| Парткод: | F0-01451000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | RFCC-525S |
| Парткод: | F0-01556000 |
| Деталь: | SPLSN-6U |
| Парткод: | F0-00342000 |
| Деталь: | RFC-33V0 |
| Парткод: | F0-01418000 |
| Деталь: | RFC-45V0 |
| Парткод: | F0-01858000 |
| Деталь: | COVER-HNS-380D |
| Парткод: | 6LE29018000 |
| Деталь: | BRKT-DOOR-SW-380 |
| Парткод: | 6LE22817000 |
| Деталь: | SLIDE-SW-ADU |
| Парткод: | 6LE22823000 |
| Деталь: | FA1L-AA22 |
| Парткод: | E0-08442000 |
| Деталь: | GUIDE-SW-DOOR-380 |
| Парткод: | 6LE22819000 |
| Деталь: | stud-door-sw |
| Парткод: | 6LE22824000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | SCREW-CH-M |
| Парткод: | 6LE06406000 |
| Деталь: | SPG-E-6R5XR45X31R9 |
| Парткод: | 6LE22836000 |
| Деталь: | DUCT-OZN-FAN-B |
| Парткод: | 6LH32920000 |
| Деталь: | ASYS-DUCT-FAN-60 |
| Парткод: | 6LH32921000 |
| Деталь: | ASYS-DUCT-OZN-A |
| Парткод: | 6LH32941000 |
| Деталь: | ASYS-DUCT-EPU-COOL-B |
| Парткод: | 6LH32929000 |
| Деталь: | FAND-DEV-390 |
| Парткод: | 6LE09187000 |
| Деталь: | ASYS-DUCT-EPU-COOL-A |
| Парткод: | 6LH32926000 |
| Деталь: | S/BID-M4X35-NI |
| Парткод: | X0-00461000 |
| Деталь: | DUCT-TNR-EXIT-U |
| Парткод: | 6LE22508000 |
| Деталь: | ASYS-DUCT-TNR-EXIT-L |
| Парткод: | 6LH36291000 |
| Деталь: | ASYS-DUCT-FAN |
| Парткод: | 6LE22571000 |
| Деталь: | FLTR-OZ-50-TNR-EX-450 |
| Парткод: | 6LH32949000 |
| Деталь: | HRNS-FIL-POW-350 |
| Парткод: | 6LA41968000 |
| Деталь: | MARK-EARTH-VDE-371 |
| Парткод: | 6LA91550000 |
| Деталь: | PS-HVT-450 |
| Парткод: | 6LH39912000 |
| Деталь: | PLATE-LVPS-CON-F380 |
| Парткод: | 6LE22855000 |
| Деталь: | AJ76101BF |
| Парткод: | E0-11767000 |
| Деталь: | RFC-33V0 |
| Парткод: | F0-01418000 |
| Деталь: | PWA-F-FIL-450-U |
| Парткод: | 6LH39819000 |
| Деталь: | PWA-F-FIL-450-E |
| Парткод: | 6LH39819100 |
| Деталь: | ASYB-PSU-F450UA |
| Парткод: | 6LH39979000 |
| Деталь: | ASYB-PSU-F450-EA |
| Парткод: | 6LH39979200 |
| Деталь: | ASYB-PSU-F450-UB |
| Парткод: | 6LH39979100 |
| Деталь: | ASYB-PUS-F450-EB |
| Парткод: | 6LH39979300 |
| Деталь: | NC-179-F6.35 |
| Парткод: | E0-06067000 |
| Деталь: | S/PAN/SWWS-M4X6-NI |
| Парткод: | X0-02093000 |
| Деталь: | SPLSN-8U |
| Парткод: | F0-00343000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | S/FHEXM-M4X8-NI |
| Парткод: | X0-02235000 |
| Деталь: | SPLSN-4U |
| Парткод: | F0-00340000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | LES-0510 |
| Парткод: | F0-01483000 |
| Деталь: | CABLE-P-INLET-US |
| Парткод: | 6LA55883000 |
| Деталь: | CABLE-P-INLET-EUR |
| Парткод: | 6LE95790000 |
| Деталь: | CABLE-P-INLET-AU |
| Парткод: | 6LE95791000 |
| Деталь: | CABLE-P-INLET-UK |
| Парткод: | 6LE87775000 |
| Деталь: | NRW10-15A-Y-TK1419 |
| Парткод: | E0-08475000 |
| Деталь: | NRW10-10A-Y-TK1419 |
| Парткод: | E0-08474000 |
| Деталь: | ASYS-PLATE-CRU-F |
| Парткод: | 6LE28231000 |
| Деталь: | ASYS-LINK-TBU-CRU-F |
| Парткод: | 6LE28227000 |
| Деталь: | ASYS-LINK-LIFT-CRU-F |
| Парткод: | 6LE28225000 |
| Деталь: | RAIL-GUIDE-TBU-F |
| Парткод: | 6LE28313000 |
| Деталь: | HLDR-TBU-F-CL |
| Парткод: | 6LE28393000 |
| Деталь: | HLDR-TBU-F-TR |
| Парткод: | 6LE28283000 |
| Деталь: | HLDR-RAIL-TBU |
| Парткод: | 6LE28419000 |
| Деталь: | BRKT-HLDR-TBU |
| Парткод: | 6LE28421000 |
| Деталь: | HOLDER-GUIDE-MID-L-F |
| Парткод: | 6LE28286000 |
| Деталь: | CAM-LIFT-TBU-F |
| Парткод: | 6LE28250000 |
| Деталь: | CAM-LIFT-CRU-F |
| Парткод: | 6LE28246000 |
| Деталь: | LINK-LIFT-PLATE-CRU |
| Парткод: | 6LE28294000 |
| Деталь: | SPG-HLDR-RAIL-TBU |
| Парткод: | 6LE28420000 |
| Деталь: | SPG-F-DPM-TBU-F |
| Парткод: | 6LE28338000 |
| Деталь: | WSHR-6R2X12XR5-APS |
| Парткод: | 6LE28372000 |
| Деталь: | SPG-F-FIX-TBU-CL |
| Парткод: | 6LE28508000 |
| Деталь: | SPG-F-FIX-TBU |
| Парткод: | 6LE28340000 |
| Деталь: | SCREW-TBU-F380-2 |
| Парткод: | 6LE28392000 |
| Деталь: | BRKT-SLIDE-F |
| Парткод: | 6LE25897000 |
| Деталь: | STUD-LEVER-ADU-F |
| Парткод: | 6LE23953000 |
| Деталь: | COV-FRM-TOP-BCK-380D |
| Парткод: | 6LE21701000 |
| Деталь: | SPG-TBU-F-CLN |
| Парткод: | 6LE28509000 |
| Деталь: | ASYS-BRKT-GEL-L-F-380 |
| Парткод: | 6LE27437000 |
| Деталь: | shaft-door-sw |
| Парткод: | 6LE22822000 |
| Деталь: | PUSHER-COVF-45X |
| Парткод: | 6LH33241000 |
| Деталь: | BRKT-SWCOV-45X |
| Парткод: | 6LH33240000 |
| Деталь: | SPG-C-5R75XR55X40 |
| Парткод: | 6LE22904000 |
| Деталь: | ASYS-BRKT-GEL-R-F-380 |
| Парткод: | 6LE27439000 |
| Деталь: | ASYS-ERZV10D821-350 |
| Парткод: | 6LA37732000 |
| Деталь: | HLDR-ERTH-RGST |
| Парткод: | 6LA37611000 |
| Деталь: | SPG-F-RGST-R |
| Парткод: | 6LA37612000 |
| Деталь: | SPG-F-RGST-L |
| Парткод: | 6LA37613000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | BRKT-BASE-SHUT-FRT |
| Парткод: | 6LE22527000 |
| Деталь: | BRKT-FUS-FRM-F |
| Парткод: | 6LE25890000 |
| Деталь: | STUD-HOOK-TRU |
| Парткод: | 6LE29029000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | S/FHEXM-M3X8-NI |
| Парткод: | X0-02231000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | S/TPS/BID-3X6-ZU3 |
| Парткод: | X0-02069000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | TES-016NV |
| Парткод: | F0-01551000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | S/FHEXM-M4X6-NI |
| Парткод: | X0-02234000 |
| Деталь: | S/TPS/FHEXM-4X8-ZU3 |
| Парткод: | X0-02243000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | OD-FC35 |
| Парткод: | 6LE20127000 |
| Деталь: | GN-2010 |
| Парткод: | 6A000000766 |
| Деталь: | GN-3010 |
| Парткод: | 6A000000459 |
| Деталь: | GP-1070 |
| Парткод: | 6A000001051 |
| Деталь: | GE-1170 |
| Парткод: | 6A000001048 |
| Деталь: | KP-2004 |
| Парткод: | 6A000000878 |
| Деталь: | KP-2005 |
| Парткод: | 6A000000925 |
| Деталь: | GQ-1110 |
| Парткод: | 6A000000880 |
| Деталь: | GS-1010 |
| Парткод: | 6A000001055 |
| Деталь: | GS-1020 |
| Парткод: | 6A000001057 |
| Деталь: | GP-1080 |
| Парткод: | 6A000001053 |
| Деталь: | D-FC28-K |
| Парткод: | 6LE98164300 |
| Деталь: | D-FC28-Y |
| Парткод: | 6LE98164000 |
| Деталь: | D-FC28-M |
| Парткод: | 6LE98164100 |
| Деталь: | D-FC28-C |
| Парткод: | 6LE98164200 |
| Деталь: | PS-ZTFC28K(1) |
| Парткод: | 6AK00000087 |
| Деталь: | PS-ZTFC28EK(1) |
| Парткод: | 6AK00000081 |
| Деталь: | PS-ZTFC28DK(1) |
| Парткод: | 6AG00002106 |
| Деталь: | PS-ZTFC28CK(1) |
| Парткод: | 6AG00002125 |
| Деталь: | PS-ZTFC28Y(1) |
| Парткод: | 6AG00002122 |
| Деталь: | PS-ZTFC28EY(1) |
| Парткод: | 6AG00002112 |
| Деталь: | PS-ZTFC28DY(1) |
| Парткод: | 6AG00002110 |
| Деталь: | PS-ZTFC28CY(1) |
| Парткод: | 6AG00002127 |
| Деталь: | PS-ZTFC28M(1) |
| Парткод: | 6AK00000089 |
| Деталь: | PS-ZTFC28EM(1) |
| Парткод: | 6AK00000084 |
| Деталь: | PS-ZTFC28DM(1) |
| Парткод: | 6AG00002108 |
| Деталь: | PS-ZTFC28CM(1) |
| Парткод: | 6AG00002126 |
| Деталь: | PS-ZTFC28C(1) |
| Парткод: | 6AK00000083 |
| Деталь: | PS-ZTFC28EC(1) |
| Парткод: | 6AK00000079 |
| Деталь: | PS-ZTFC28DC(1) |
| Парткод: | 6AG00002128 |
| Деталь: | PS-ZTFC28CC(1) |
| Парткод: | 6AG00002124 |
| Деталь: | PS-TBFC28 |
| Парткод: | 6AG00002037 |
| Деталь: | PS-TBFC28E |
| Парткод: | 6AG00002039 |
| Деталь: | PS-TBFC28C |
| Парткод: | 6AG00002038 |
| Деталь: | KA-3511PC |
| Парткод: | 6AG00000825 |
| Деталь: | KA-3511PC-C |
| Парткод: | 6AG00001376 |
| Деталь: | KK-3511 |
| Парткод: | 6AR00000615 |
| Деталь: | KK-3511-C |
| Парткод: | 6AR00000616 |
| Деталь: | MF-3500CU |
| Парткод: | 6AG00001654 |
| Деталь: | MF-3500CE |
| Парткод: | 6AG00001652 |
| Деталь: | GN-1050 |
| Парткод: | 6A000000981 |
| Деталь: | GN-1050C |
| Парткод: | 6A000001050 |
| Деталь: | ASYS-CASE-DEV-SEAL-F45X |
| Парткод: | 6LH33543000 |
| Деталь: | SEAL-VC6-10-2.5 |
| Парткод: | 4401949290 |
| Деталь: | SEAL-VC8-12-2.5 |
| Парткод: | 4406333150 |
| Деталь: | ASYS-BUSH-6X12-10F |
| Парткод: | 6LH33531000 |
| Деталь: | MIXER-1-380-25 |
| Парткод: | 6LE23152000 |
| Деталь: | GEAR-8H18-DEV |
| Парткод: | 6LE23185000 |
| Деталь: | WAS-POLY-4 |
| Парткод: | 4406527980 |
| Деталь: | SPG-C-CPG-DEV |
| Парткод: | 6LE23186000 |
| Деталь: | CPG-DRV-DEV |
| Парткод: | 6LE23184000 |
| Деталь: | ASYS-MIXER-2-F45X |
| Парткод: | 6LH33552000 |
| Деталь: | GEAR-8H18-6-R |
| Парткод: | 6LE23155000 |
| Деталь: | HLDR-BUSH-DEV-F |
| Парткод: | 6LE23135000 |
| Деталь: | BUSH-SEAL-6-M |
| Парткод: | 6LA30779000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | RLR-MAGT-F45X |
| Парткод: | 6LH33554000 |
| Деталь: | ASYS-SEAL-DUCT-DEV |
| Парткод: | 6LE23611000 |
| Деталь: | RLR-GUIDE-DEV-035 |
| Парткод: | 6LE23156000 |
| Деталь: | ASYS-SEAL-SHUT-DEV |
| Парткод: | 6LE23610000 |
| Деталь: | GEAR-8H19-8-L |
| Парткод: | 6LE23157000 |
| Деталь: | ASYS-GEAR-8H22-5-L-BR |
| Парткод: | 6LE23190000 |
| Деталь: | ASYS-GEAR-8H17-5-R-BR |
| Парткод: | 6LE23191000 |
| Деталь: | STUD-GEAR-DEV |
| Парткод: | 6LE23161000 |
| Деталь: | ASYS-HLDR-GEAR-DEV |
| Парткод: | 6LE23239000 |
| Деталь: | ADJSTR-MG-2 |
| Парткод: | 6LE23162000 |
| Деталь: | ASYS-COVER-DEV-F45X |
| Парткод: | 6LH33561000 |
| Деталь: | ASYS-DOCTOR-F45X |
| Парткод: | 6LH33548000 |
| Деталь: | SEAL-MG-SIDE-F |
| Парткод: | 6LE23163000 |
| Деталь: | SEAL-MG-SIDE-R |
| Парткод: | 6LE23164000 |
| Деталь: | ASYS-HLDR-SHIELD-DEV |
| Парткод: | 6LE23605000 |
| Деталь: | SEAL-ATC-BLK |
| Парткод: | 6LA29904000 |
| Деталь: | SNSR-ATC-380 |
| Парткод: | 6LE29460000 |
| Деталь: | HRNS-ATS-380 |
| Парткод: | 6LE29394000 |
| Деталь: | PLATE-DEV-COOLER |
| Парткод: | 6LH33523000 |
| Деталь: | SEAL-MG-DOC-L |
| Парткод: | 6LE23212000 |
| Деталь: | SEAL-DOC-SIDE-F |
| Парткод: | 6LE23218000 |
| Деталь: | SEAL-DOC-SIDE-R |
| Парткод: | 6LE23219000 |
| Деталь: | SEAL-MIXER-380 |
| Парткод: | 6LE23233000 |
| Деталь: | ASYS-DUCT-DEV-COV |
| Парткод: | 6LH33564000 |
| Деталь: | ASYS-SEAL-DOC-SIDE-R |
| Парткод: | 6LH33574000 |
| Деталь: | DUCT-DEV-COOLER |
| Парткод: | 6LH33524000 |
| Деталь: | L-1680DDRPOP25LY13 |
| Парткод: | F0-01206000 |
| Деталь: | S/PAN/SWWS-M3X6-BS |
| Парткод: | X0-01973000 |
| Деталь: | S5103-31 3BC |
| Парткод: | F0-01499000 |
| Деталь: | S/BID-M3X4-NI |
| Парткод: | X0-00426000 |
| Деталь: | CO0525A |
| Парткод: | F0-01642000 |
| Деталь: | THMS-DRM-380 |
| Парткод: | 6LE29461000 |
| Деталь: | ASYS-FRM-FEEDER-R |
| Парткод: | 6LE24223000 |
| Деталь: | RAIL-CST-RGT-380 |
| Парткод: | 6LE24209000 |
| Деталь: | RAIL-CSSTT-RGT |
| Парткод: | 6LA64841000 |
| Деталь: | SLIDER-CST |
| Парткод: | 41306007000 |
| Деталь: | CATCH-CST-380 |
| Парткод: | 6LE24257000 |
| Деталь: | CATCH-CST-320 |
| Парткод: | 44201601000 |
| Деталь: | BUSH-ROL-FEEDER |
| Парткод: | 44201613000 |
| Деталь: | ROLLER-FEEDER-380 |
| Парткод: | 6LE24203000 |
| Деталь: | GEAR-10S35_P3GT25-6 |
| Парткод: | 6LE24242000 |
| Деталь: | GEAR-10S20_10S32-6 |
| Парткод: | 6LE24243000 |
| Деталь: | GEAR-10S29-6 |
| Парткод: | 6LE24254000 |
| Деталь: | GEAR-10S21-8 |
| Парткод: | 6LE24265000 |
| Деталь: | GEAR-10S31-6 |
| Парткод: | 6LE24266000 |
| Деталь: | GEAR-10S25_10S27-6 |
| Парткод: | 6LE24292000 |
| Деталь: | GEAR-10S023-06 |
| Парткод: | 44201367000 |
| Деталь: | GEAR-10S22-6-TR2 |
| Парткод: | 6LA41184000 |
| Деталь: | GEAR-10S20_10S25-6 |
| Парткод: | 6LA64833000 |
| Деталь: | BLT/T-297-3GT-4 |
| Парткод: | 6LA04271000 |
| Деталь: | BRKT-DRV-FEEDER-CL |
| Парткод: | 6LE24263000 |
| Деталь: | ASYS-SHAFT-DRV-TR1-CL |
| Парткод: | 6LE24285000 |
| Деталь: | CLUTCH-G28-08D-30A |
| Парткод: | 6LE40813000 |
| Деталь: | COVER-RAIL-CST |
| Парткод: | 6LE24268000 |
| Деталь: | FOOT-MAIN-AT |
| Парткод: | 41306501000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | STOP RING |
| Парткод: | 41306265000 |
| Деталь: | BUSH-8X12X8F-NU4 |
| Парткод: | 6LH23442000 |
| Деталь: | ASYS-BRKT-ADU-R-450 |
| Парткод: | 6LH31404000 |
| Деталь: | BRKT-HOLD-BYP-R |
| Парткод: | 6LE21204000 |
| Деталь: | ASYS-BRKT-ADU-FRT |
| Парткод: | 6LE21216000 |
| Деталь: | 55533-1219 |
| Парткод: | E0-08733000 |
| Деталь: | CS1A-B2CA |
| Парткод: | E0-01853000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | MSB-1207 |
| Парткод: | F0-01250000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | S/TPS/BID-4X8-ZU3 |
| Парткод: | X0-02074000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | S/TPS/FHEXM-4X8-ZU3 |
| Парткод: | X0-02243000 |
| Деталь: | S/TPS/BID-3X8-ZU3 |
| Парткод: | X0-02070000 |
| Деталь: | MOTR_S-DRUM-380 |
| Парткод: | 6LE22137000 |
| Деталь: | MYLAR-SW-RGST-2 |
| Парткод: | 44201543000 |
| Деталь: | GEAR-5H66-8-IDLER-DRUM |
| Парткод: | 6LE22115000 |
| Деталь: | STOP RING |
| Парткод: | 41306265000 |
| Деталь: | SPG-C-IDL-RER-N |
| Парткод: | 6LE22213000 |
| Деталь: | COUPL-IDL-DRUM |
| Парткод: | 6LE22121000 |
| Деталь: | ASYS-SHAFT-DRV-DRUM-C-450 |
| Парткод: | 6LH32507000 |
| Деталь: | SPG-C-IDL-FRT |
| Парткод: | 6LE22128000 |
| Деталь: | COLAR-IDL-DRUM |
| Парткод: | 6LE22107000 |
| Деталь: | ASYS-SHAFT-DRIVE-DRUM-MC |
| Парткод: | 6LE22139000 |
| Деталь: | ASYS-SHAFT-DRV-DRUM-K-450 |
| Парткод: | 6LH32506000 |
| Деталь: | COLAR-DRIVE-DRUM |
| Парткод: | 6LE22133000 |
| Деталь: | GEAR-5H132-8-DRUM |
| Парткод: | 6LE22114000 |
| Деталь: | SPG-C-DRIVE-DRUM |
| Парткод: | 6LE22135000 |
| Деталь: | COUPL-DRIVE-DRUM-380 |
| Парткод: | 6LE22209000 |
| Деталь: | GUIDE-SEP-GEAR-IDL |
| Парткод: | 6LE22211000 |
| Деталь: | ASYS-BRKT-MOTR-SEP-IDL |
| Парткод: | 6LH32516000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | HRNS-SNS-DRM-380 |
| Парткод: | 6LE29389000 |
| Деталь: | GEAR-5H35_5S25-6 |
| Парткод: | 6LE22124000 |
| Деталь: | GEAR-5S35_5S25-6 |
| Парткод: | 6LE22125000 |
| Деталь: | S/BID-M3X4-ZC3-RED |
| Парткод: | 6LE22138000 |
| Деталь: | DISK-DRIVE-DRUM |
| Парткод: | 6LH32508000 |
| Деталь: | MYLAR-COV-SNSR |
| Парткод: | 6LH32520000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | S/PAN-M3X3-NI |
| Парткод: | X0-02112000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | LWS-1316Z |
| Парткод: | F0-01245000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | ACTR-CAM-LIFT-EXN |
| Парткод: | 6LE28396000 |
| Деталь: | LINK-YMC-F-CL |
| Парткод: | 6LE28378000 |
| Деталь: | LINK-YMC-R-CL |
| Парткод: | 6LE28377000 |
| Деталь: | LINK-YMC-F-EX |
| Парткод: | 6LE28298000 |
| Деталь: | ASYS-BRKT-LIFT |
| Парткод: | 6LE28219000 |
| Деталь: | ASYS-BRUSH-TBU-F380 |
| Парткод: | 6LE28409000 |
| Деталь: | SHAFT-LIFT-TBU |
| Парткод: | 6LE28327000 |
| Деталь: | SHAFT-LINK-TBU |
| Парткод: | 6LE28328000 |
| Деталь: | ASYS-STAY-TBU-H-CL |
| Парткод: | 6LE28462000 |
| Деталь: | ASYS-STAY-TBU-H-TR |
| Парткод: | 6LE28463000 |
| Деталь: | STAY-TBU-V |
| Парткод: | 6LE28495000 |
| Деталь: | BRKT-LINK-YMC-EX |
| Парткод: | 6LE28444000 |
| Деталь: | GEAR-5H28-6 |
| Парткод: | 6LE28267000 |
| Деталь: | GEAR-5H47-8 |
| Парткод: | 6LE28268000 |
| Деталь: | GEAR-5H64_5H19-6 |
| Парткод: | 6LE28269000 |
| Деталь: | GEAR-5H71_5H18-6 |
| Парткод: | 6LE28270000 |
| Деталь: | ASYS-MOTRD-TBU-LIFT-450 |
| Парткод: | 6LH38615000 |
| Деталь: | BRKT-BRUSH-TBU-CL |
| Парткод: | 6LE28406000 |
| Деталь: | BRKT-BRUSH-TBU-DRV |
| Парткод: | 6LE28397000 |
| Деталь: | BRKT-BRUSH-TBU-TR |
| Парткод: | 6LE28398000 |
| Деталь: | COVER-SNSR-LIFT |
| Парткод: | 6LA29902000 |
| Деталь: | GUIDE-LINK-TBU |
| Парткод: | 6LE28274000 |
| Деталь: | BUSH-8 |
| Парткод: | 4400802080 |
| Деталь: | CAM-LIFT-EX-FN |
| Парткод: | 6LE28394000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | UAMS-05-2 |
| Парткод: | F0-00044000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | S/PAN-M2.6X4-NC |
| Парткод: | X0-01670000 |
| Деталь: | LWS-0711Z |
| Парткод: | F0-00736000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | S/TPS/FHEXM-3X8-ZU3 |
| Парткод: | X0-02239000 |
| Деталь: | COV-CNCT-DWN |
| Парткод: | 6LA34629000 |
| Деталь: | COV-CNCT-USB-H |
| Парткод: | 6LA34648000 |
| Деталь: | EDS-2323U |
| Парткод: | F0-00034000 |
| Деталь: | EDS-1717U |
| Парткод: | F0-00047000 |
| Деталь: | SPSN-4U |
| Парткод: | F0-00331000 |
| Деталь: | SHCBS-14 |
| Парткод: | F0-01756000 |
| Деталь: | RLWC-2SV0 |
| Парткод: | F0-01609000 |
| Деталь: | PWA-F-IMG-450 |
| Парткод: | 6LH39833000 |
| Деталь: | HRNS-SYS-FAN-450 |
| Парткод: | 6LH39761000 |
| Деталь: | S/TPS/FHEXM-3X8-ZU3 |
| Парткод: | X0-02239000 |
| Деталь: | S/BID-M3X6-NI |
| Парткод: | X0-00430000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | MSB-1207 |
| Парткод: | F0-01250000 |
| Деталь: | ASYB-PWA-SYS-450S |
| Парткод: | 6LH39933000 |
| Деталь: | WD800JD-22LSA1 |
| Парткод: | G0-00496000 |
| Деталь: | GST-100-RFM4 |
| Парткод: | E0-05933000 |
| Деталь: | RLWS-1TV0 |
| Парткод: | F0-00367000 |
| Деталь: | SCREW-6-32X1/4 |
| Парткод: | 6LE82485000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | HED-1111-ALS20ABK |
| Парткод: | F0-01327000 |
| Деталь: | SCREW-HDD-CASE |
| Парткод: | 6LA56769000 |
| Деталь: | RFC-10 |
| Парткод: | D0-07098000 |
| Деталь: | T30R |
| Парткод: | F0-01437000 |
| Деталь: | HRNS-SATA-SIG-450 |
| Парткод: | 6LH39875000 |
| Деталь: | HRNS-SATA-POW-450 |
| Парткод: | 6LH39760000 |
| Деталь: | FAN_D-SYS-6025-430 |
| Парткод: | 6LH08778000 |
| Деталь: | S/FHEXM-M4X8-NI |
| Парткод: | X0-02235000 |
| Деталь: | S/TPS/PAN-4X32-ZU3 |
| Парткод: | X0-02114000 |
| Деталь: | SPG-F-SYS-EARTH |
| Парткод: | 6LH33235000 |
| Деталь: | ASYB-PWA-LGC-450S |
| Парткод: | 6LH40026000 |
| Деталь: | ASYB-PWA-LGC-451S |
| Парткод: | 6LH40026100 |
| Деталь: | ASYB-PWA-LGC-452S |
| Парткод: | 6LH40026200 |
| Деталь: | ASYB-PWA-LGC-453S |
| Парткод: | 6LH40026300 |
| Деталь: | ASYB-PWA-LGC-454S |
| Парткод: | 6LH40026400 |
| Деталь: | CASE-CHARGR-MAIN-380 |
| Парткод: | 6LE23550000 |
| Деталь: | TERM-CHARGR-MAIN-FRT |
| Парткод: | 6LE23551000 |
| Деталь: | TERM-CHARGR-MAIN-RER |
| Парткод: | 6LE23626000 |
| Деталь: | SPG-F-CHARGR-EPU-RER |
| Парткод: | 6LE23627000 |
| Деталь: | ELCTRD-CHARGR-MAIN-380 |
| Парткод: | 6LE23554000 |
| Деталь: | SPG-E-4XR5X11R2-CHARGR |
| Парткод: | 6LE23557000 |
| Деталь: | SEESAW-GRID-ELCTRD |
| Парткод: | 6LE23553000 |
| Деталь: | LID-CHARGR-MAIN-FRT |
| Парткод: | 6LE23559000 |
| Деталь: | LID-CHARGR-MAIN-RER |
| Парткод: | 6LE23560000 |
| Деталь: | SHEET-ERASE-CHARGR |
| Парткод: | 6LE23558000 |
| Деталь: | ROD-CHARGR-CLNR-380 |
| Парткод: | 6LE23567000 |
| Деталь: | GRID-CHARGR-MAIN-380 |
| Парткод: | 6LE23555000 |
| Деталь: | FILM-CLNR-CHARGR-380 |
| Парткод: | 6LE23564000 |
| Деталь: | S/TPP/PAN-3X6-NI |
| Парткод: | X0-00595000 |
| Деталь: | ROLLER-RGST-R |
| Парткод: | 6LE24202000 |
| Деталь: | GEAR-0.8-25 |
| Парткод: | 4407547320 |
| Деталь: | GUIDE-IDLE-TR1 |
| Парткод: | 6LE24375000 |
| Деталь: | ROLLER-IDLA |
| Парткод: | 6LA37628000 |
| Деталь: | SHAFT-IDLE-TR1 |
| Парткод: | 6LE24381000 |
| Деталь: | LVR-SEP-RELAY-F-371 |
| Парткод: | 6LA88317000 |
| Деталь: | LVR-SEP-RELAY-R-371 |
| Парткод: | 6LA88318000 |
| Деталь: | SPG-E-7XR9X107R15 |
| Парткод: | 6LE24329000 |
| Деталь: | ASYS-BRKT-TRU-R |
| Парткод: | 6LE29031000 |
| Деталь: | ASYS-PLT-TRU-F |
| Парткод: | 6LE29036000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | TRAY-BYP-LOW-380 |
| Парткод: | 6LE21264000 |
| Деталь: | TRAY-BYP-UP-380 |
| Парткод: | 6LE21263000 |
| Деталь: | TRAY-BYP-M-380 |
| Парткод: | 6LE21241000 |
| Деталь: | GUIDE-TRAY-FRT-380 |
| Парткод: | 6LE21243000 |
| Деталь: | GUIDE-TRAY-RER-380 |
| Парткод: | 6LE21244000 |
| Деталь: | ASYS-PLATE-PINION-380 |
| Парткод: | 6LE21247000 |
| Деталь: | pinion-18-395 |
| Парткод: | 4407726480 |
| Деталь: | ASYS-RACK-BYPASS-380 |
| Парткод: | 6LE21265000 |
| Деталь: | RACK-BYPASS-380 |
| Парткод: | 6LE21245000 |
| Деталь: | SPL-PLATE-PINION |
| Парткод: | 6LE21242000 |
| Деталь: | PWA-F-SFB-380 |
| Парткод: | 6LE29825000 |
| Деталь: | PAD-BRAKE |
| Парткод: | 4400901130 |
| Деталь: | HRNS-SFB-SIZE-360 |
| Парткод: | 6LA71350000 |
| Деталь: | LBL-HIGH-TRAY-350 |
| Парткод: | 6LA29002000 |
| Деталь: | ASYS-BRKT-BYP-R-380 |
| Парткод: | 6LE21229000 |
| Деталь: | ASYS-SFT-TRAY-BYPS-R |
| Парткод: | 6LE21232000 |
| Деталь: | SPA-HINGE-BYPASS |
| Парткод: | 6LA28948000 |
| Деталь: | BUSH-8 |
| Парткод: | 4400802080 |
| Деталь: | LEVER-GUIDE-F |
| Парткод: | 6LA29006000 |
| Деталь: | SPG-GUIDE-F |
| Парткод: | 6LA29007000 |
| Деталь: | SHEET-PAD-GUIDE-F-380 |
| Парткод: | 6LE21250000 |
| Деталь: | S/BID-M3X6-NI |
| Парткод: | X0-00430000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | S/TPS/FHEXM/R-3X6-ZU3 |
| Парткод: | X0-02419000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/TPS/FHEXM/R-3X8-ZU3 |
| Парткод: | X0-02420000 |
| Деталь: | UAMS-07-0 |
| Парткод: | F0-00033000 |
| Деталь: | S/TPP/PAN-3X6-NI |
| Парткод: | X0-00595000 |
| Деталь: | LBL-TRAY-U-350 |
| Парткод: | 6LA29000000 |
| Деталь: | LBL-TRAY-E-350 |
| Парткод: | 6LA29003000 |
| Деталь: | ASYS-GUIDE-FEEDER-LEFT |
| Парткод: | 6LE24317000 |
| Деталь: | GUIDE-FEEDER-RIGHT-UP |
| Парткод: | 6LE24204000 |
| Деталь: | GUIDE-FEED-BYPASS |
| Парткод: | 6LE24206000 |
| Деталь: | ACTR-SNSR-FED-LOW |
| Парткод: | 6LE24230000 |
| Деталь: | SPG-T-SNSR-LOW-350 |
| Парткод: | 6LA37703000 |
| Деталь: | MYLAR-SW-RGST-2 |
| Парткод: | 44201543000 |
| Деталь: | HRNS-FEED2-380 |
| Парткод: | 6LE29400000 |
| Деталь: | GUIDE-COV-FED-L |
| Парткод: | 6LE24321000 |
| Деталь: | KNOB-COVER-FEED |
| Парткод: | 6LE46201000 |
| Деталь: | SHAFT-FEED-LOW-350 |
| Парткод: | 6LE46205000 |
| Деталь: | ROLLER-IDLA |
| Парткод: | 6LA37628000 |
| Деталь: | BUSH-FEED-IDL |
| Парткод: | 44201623000 |
| Деталь: | SPG-C-8R2XR9X15R5 |
| Парткод: | 6LA66976000 |
| Деталь: | ASYS-BASE-HOOK-F380 |
| Парткод: | 6LE24307000 |
| Деталь: | HOOK-AK |
| Парткод: | 6LA60469000 |
| Деталь: | SPG-E-COVER-FEED |
| Парткод: | 6LE24341000 |
| Деталь: | GUIDE-OPEN-L |
| Парткод: | 44201627000 |
| Деталь: | STOPPER-COV-FED |
| Парткод: | 44201629000 |
| Деталь: | GUIDE-HOOK-COVER-FEED |
| Парткод: | 6LE24332000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | CS1A-B2CA |
| Парткод: | E0-01853000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/TPP/FHEXM-4X12-NI |
| Парткод: | X0-02253000 |
| Деталь: | S/TPP/BRZ-4X8-NI |
| Парткод: | X0-02092000 |
| Деталь: | ASYS-TNRBKT-F380 |
| Парткод: | 6LE28722000 |
| Деталь: | ASYS-TNRMTR-380S |
| Парткод: | 6LE28826000 |
| Деталь: | SPG-C-11R8XR8X20R-F380 |
| Парткод: | 6LE28706000 |
| Деталь: | ASYS-PIPE-F45X |
| Парткод: | 6LH39250000 |
| Деталь: | AUGER-TNRPATH-F380 |
| Парткод: | 6LE28707000 |
| Деталь: | SHUT-DUCT-TONER-CR |
| Парткод: | 6LE28736000 |
| Деталь: | GEAR-8H22-6-D |
| Парткод: | 6LE28713000 |
| Деталь: | SPG-C-SHUT-TNR-CR |
| Парткод: | 6LE28738000 |
| Деталь: | BUSH-061206F-M |
| Парткод: | 44204339000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | SHAFT-DRIVE-F380 |
| Парткод: | 6LE28734000 |
| Деталь: | GEAR-8H18-6-D |
| Парткод: | 6LE28824000 |
| Деталь: | GEAR-8S21-6 |
| Парткод: | 6LE28795000 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | STAY-TNR-F380 |
| Парткод: | 6LE28716000 |
| Деталь: | ASYS-PLATE-KTNR-45X |
| Парткод: | 6LH39102000 |
| Деталь: | GEAR-5H68_8S39-6-F45X-E |
| Парткод: | 6LH39253000 |
| Деталь: | GEAR-5H68_8S39-6-F45X-D |
| Парткод: | 6LH39253200 |
| Деталь: | GEAR-5H68_8S39-6-F45X-U |
| Парткод: | 6LH39253100 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | S/BID-M2.6X3-NI |
| Парткод: | X0-02557000 |
| Деталь: | S/TPS/FHEXM-3X8-ZU3 |
| Парткод: | X0-02239000 |
| Деталь: | None |
| Парткод: | 6LE21721000 |
| Деталь: | None |
| Парткод: | 6LA29564000 |
| Деталь: | None |
| Парткод: | 6LA29563000 |
| Деталь: | None |
| Парткод: | 6LE40910000 |
| Деталь: | None |
| Парткод: | 6LH32117000 |
| Деталь: | None |
| Парткод: | 6LH37821000 |
| Деталь: | None |
| Парткод: | 6LE21724000 |
| Деталь: | None |
| Парткод: | 6LH32113000 |
| Деталь: | None |
| Парткод: | 6LH32115000 |
| Деталь: | None |
| Парткод: | 6LE21727000 |
| Деталь: | None |
| Парткод: | 6LE40929000 |
| Деталь: | None |
| Парткод: | 6LE75819000 |
| Деталь: | None |
| Парткод: | 6LA29554000 |
| Деталь: | None |
| Парткод: | 6LE27466000 |
| Деталь: | None |
| Парткод: | 6LA47529000 |
| Деталь: | None |
| Парткод: | 6LA47633000 |
| Деталь: | None |
| Парткод: | 6LE27461000 |
| Деталь: | None |
| Парткод: | X0-02541000 |
| Деталь: | None |
| Парткод: | X0-02235000 |
| Деталь: | None |
| Парткод: | X0-02421000 |
| Деталь: | None |
| Парткод: | 6LE35418000 |
| Деталь: | None |
| Парткод: | 6LE35420000 |
| Деталь: | None |
| Парткод: | 4400740530 |
| Деталь: | None |
| Парткод: | 4400685400 |
| Деталь: | None |
| Парткод: | 4408860880 |
| Деталь: | None |
| Парткод: | 6LE90046000 |
| Деталь: | ASYS-BKT-FUS-DR-F45X |
| Парткод: | 6LH36287000 |
| Деталь: | GEAR-10S40-REV |
| Парткод: | 6LE25996000 |
| Деталь: | MOTR_D-FUSER-450 |
| Парткод: | 6LH36234000 |
| Деталь: | GEAR-FUS-HAND |
| Парткод: | 6LE25933000 |
| Деталь: | GR-10S30-10S42 |
| Парткод: | 6LE25907000 |
| Деталь: | GR-10S23-05H50 |
| Парткод: | 6LE25909000 |
| Деталь: | GEAR-10S23-REV |
| Парткод: | 6LE25995000 |
| Деталь: | GEAR-10S23-21 |
| Парткод: | 6LE25926000 |
| Деталь: | GEAR-10S29 |
| Парткод: | 6LE25908000 |
| Деталь: | GEAR-10S027-06 |
| Парткод: | 44201361000 |
| Деталь: | GEAR-10S023-06 |
| Парткод: | 44201367000 |
| Деталь: | GEAR-10S016-06-BCL |
| Парткод: | 6LA32521000 |
| Деталь: | SFT-FUS-DRV-REV |
| Парткод: | 6LE25994000 |
| Деталь: | SHAFT-FUS-MOT |
| Парткод: | 6LE25842000 |
| Деталь: | BUSH-8X12X8F-NU4 |
| Парткод: | 6LH23442000 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | DUCT-EXIT-FAN |
| Парткод: | 6LH36339000 |
| Деталь: | FAN-F380-80 |
| Парткод: | 6LE22868000 |
| Деталь: | GEAR-10S15_PS2M37 |
| Парткод: | 6LE23942000 |
| Деталь: | BLT_SY-40S2M-098 |
| Парткод: | 6LE23936000 |
| Деталь: | ASYB-BRKT-MOTR-EXIT |
| Парткод: | 6LH36333000 |
| Деталь: | GEAR-10S25-6 |
| Парткод: | 6LH36289000 |
| Деталь: | GEAR-10S32_10S19-6 |
| Парткод: | 6LH36290000 |
| Деталь: | COV-DUCT-EXIT-FAN |
| Парткод: | 6LH36342000 |
| Деталь: | LWS-0711Z |
| Парткод: | F0-00736000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | P/PRL/AH7-2X16-SS |
| Парткод: | X0-01533000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | S/PAN/SWWP-M4X8-ZU3 |
| Парткод: | X0-02217000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | S/TPS/PAN-4X32-ZU3 |
| Парткод: | X0-02114000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/TPP/FHEXM-4X8-NI |
| Парткод: | X0-02251000 |
| Деталь: | case-drv-try-f |
| Парткод: | 44201850000 |
| Деталь: | case-drv-try-r |
| Парткод: | 44201851000 |
| Деталь: | CPG-LIFT-28 |
| Парткод: | 41306022000 |
| Деталь: | SPC172-100-3400 |
| Парткод: | 4401966050 |
| Деталь: | GER-TRAY-21 |
| Парткод: | 41306025000 |
| Деталь: | GER-TRAY-24-14 |
| Парткод: | 41306024000 |
| Деталь: | G06S-13-G05S-80 |
| Парткод: | 44201853000 |
| Деталь: | G05H-45/G05S-15 |
| Парткод: | 44201854000 |
| Деталь: | ASYS-MOTR-D-TRAY-210 |
| Парткод: | 6LE71176000 |
| Деталь: | COV-SIDE-BOX-450D |
| Парткод: | 6LH32119000 |
| Деталь: | S/TPP/FLT-4X8-NI |
| Парткод: | 6LE26502000 |
| Деталь: | COV-WTNR-FRT-DOOR-1 |
| Парткод: | 6LH32123000 |
| Деталь: | COV-WTNR-FRT-DOOR-2 |
| Парткод: | 6LH32122000 |
| Деталь: | STOPPER-COV-FRT-WTNR |
| Парткод: | 6LH32120000 |
| Деталь: | ASYS-STAY-DRV-BOX |
| Парткод: | 6LH39161000 |
| Деталь: | GEAR-5H66-CPL |
| Парткод: | 6LH39164000 |
| Деталь: | SPG-C-DRV-CPL-WTNR |
| Парткод: | 6LH39165000 |
| Деталь: | MOTRD-PDL-450 |
| Парткод: | 6LH39804000 |
| Деталь: | ASYB-CASE-FLTR-OZN-45X |
| Парткод: | 6LH32914000 |
| Деталь: | FLTR-OZN-45X-CBO-600M |
| Парткод: | 6LH32948000 |
| Деталь: | SHEET-SNR-LG |
| Парткод: | 6LE28797000 |
| Деталь: | LWS-0711Z |
| Парткод: | F0-00736000 |
| Деталь: | S/TPS/FHEXM-4X8-ZU3 |
| Парткод: | X0-02243000 |
| Деталь: | LES-1010 |
| Парткод: | F0-00542000 |
| Деталь: | S/TPP/FHEXM-4X8-NI |
| Парткод: | X0-02251000 |
| Деталь: | LWS-1316Z |
| Парткод: | F0-01245000 |
| Деталь: | CA0143-A01C |
| Парткод: | F0-01805000 |
| Деталь: | S/PAN-M2.6X4-NC |
| Парткод: | X0-01670000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | LG285L2-R |
| Парткод: | C0-13512000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | SPG-C-16R5X1R4X56R2-TR2 |
| Парткод: | 6LH39400000 |
| Деталь: | SCREW-SPG-TR2 |
| Парткод: | 6LE46468000 |
| Деталь: | ARM-TRU-F |
| Парткод: | 6LH39403000 |
| Деталь: | SPG-E-8XR8X30R6-TRU |
| Парткод: | 6LE29059000 |
| Деталь: | STUD-PIVOT-TRU |
| Парткод: | 6LE29035000 |
| Деталь: | SPG-F-ARM-R-TRU |
| Парткод: | 6LE29067000 |
| Деталь: | ARM-TRU-R |
| Парткод: | 6LH39402000 |
| Деталь: | HOLDER-ROL |
| Парткод: | 6LE29037000 |
| Деталь: | CR-FC35TR2 |
| Парткод: | 6LE95128000 |
| Деталь: | BUSH-TRU-ROL |
| Парткод: | 6LE29040000 |
| Деталь: | STOP-RING-6-1.5 |
| Парткод: | 44201801000 |
| Деталь: | PLATE-GUIDE-TRU |
| Парткод: | 6LE29066000 |
| Деталь: | GUIDE-TRU-380 |
| Парткод: | 6LE29065000 |
| Деталь: | PLT-SNSR-TRU |
| Парткод: | 6LE29060000 |
| Деталь: | PLT-EARTH-TRU |
| Парткод: | 6LE29026000 |
| Деталь: | HRNS-TRUFAN-380 |
| Парткод: | 6LE29642000 |
| Деталь: | LEVER-LOCK-TRU-380 |
| Парткод: | 6LE29027000 |
| Деталь: | SHAFT-HOOK-TRU |
| Парткод: | 6LE29039000 |
| Деталь: | HOOK-TRU-380 |
| Парткод: | 6LE29038000 |
| Деталь: | SPG-E-6R1XR6X25R4-TRU |
| Парткод: | 6LE29061000 |
| Деталь: | HOLDER-RGST-SPE |
| Парткод: | 6LE24244000 |
| Деталь: | SPG-C-10R1X1X48R4 |
| Парткод: | 6LE24299000 |
| Деталь: | BUSH-ROL-RGST-F |
| Парткод: | 6LE24272000 |
| Деталь: | BUSH-8X12X8F-NU4 |
| Парткод: | 6LH23442000 |
| Деталь: | SPG-C-10X1X52R7 |
| Парткод: | 6LE24380000 |
| Деталь: | BUSH-ROL-RGST-R |
| Парткод: | 6LE24249000 |
| Деталь: | ASYS-GUIDE-RGST-R-380 |
| Парткод: | 6LE24301000 |
| Деталь: | SPG-C-10R8X1X38R5 |
| Парткод: | 6LE24330000 |
| Деталь: | ASYS-BRKT-GUIDE-TR1 |
| Парткод: | 6LE24376000 |
| Деталь: | COVER-TRU-380D |
| Парткод: | 6LE29014000 |
| Деталь: | SHEET-GUIDE-ADU |
| Парткод: | 6LE29001000 |
| Деталь: | LBL-CAU-BLT-410 |
| Парткод: | 6LE46435000 |
| Деталь: | LBL-FUS-1 |
| Парткод: | 6LA36367000 |
| Деталь: | SPL-EARTH-RGST-R |
| Парткод: | 6LE24323000 |
| Деталь: | MSB-1207 |
| Парткод: | F0-01250000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | S/TPS/FHEXM-3X8-ZU3 |
| Парткод: | X0-02239000 |
| Деталь: | DDL-1280ZZ |
| Парткод: | F0-01158000 |
| Деталь: | DDL-1680HHRP0P25LY349 |
| Парткод: | F0-01550000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | PS119EL1 |
| Парткод: | C0-12124000 |
| Деталь: | S/PAN/SWWP-M3X14-NI |
| Парткод: | X0-02135000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | ASYS-MOTR-SHUT-380 |
| Парткод: | 6LE22603000 |
| Деталь: | PLATE-SHUT-TNR-Y-45X |
| Парткод: | 6LH32902000 |
| Деталь: | PLATE-SHUT-TNR-45X |
| Парткод: | 6LH32901000 |
| Деталь: | RACK-SHUT-FRT-45X |
| Парткод: | 6LH32903000 |
| Деталь: | GUIDE-HARNESS |
| Парткод: | 6LE22861000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | GEAR-SHUT-FRT |
| Парткод: | 6LE22530000 |
| Деталь: | ACTR-SHUT-C |
| Парткод: | 6LE22610000 |
| Деталь: | RACK-SHUT-RER-45X |
| Парткод: | 6LH32904000 |
| Деталь: | SHAFT-SHUTTER |
| Парткод: | 6LE22534000 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | HRNS-LSHTU-450 |
| Парткод: | 6LH39793000 |
| Деталь: | GEAR-IDLER-08H17 |
| Парткод: | 6LE22596000 |
| Деталь: | ASYS-PL-MOTR-SHUT-D-2 |
| Парткод: | 6LE22655000 |
| Деталь: | GEAR-IDLER-08H18-U-A |
| Парткод: | 6LE22611000 |
| Деталь: | DUCT-OZN-CHA |
| Парткод: | 6LE22554000 |
| Деталь: | LAMP-ERASE-450 |
| Парткод: | 6LH39940000 |
| Деталь: | ACTR-CHARGR-MAIN |
| Парткод: | 6LE22563000 |
| Деталь: | SPG-SHUT-D-160 |
| Парткод: | 6LE22614000 |
| Деталь: | WASHER-6R2X9R5XR13-PL |
| Парткод: | 6LA78907000 |
| Деталь: | GEAR-IDLER-08H9-L-A |
| Парткод: | 6LE22612000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/TPS/BID-3X6-ZU3 |
| Парткод: | X0-02069000 |
| Деталь: | S/TPP/BID-3X6-NC |
| Парткод: | X0-01414000 |
| Деталь: | UAMS-05-2 |
| Парткод: | F0-00044000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | S/PAN-M3X3-NI |
| Парткод: | X0-02112000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | S/BID-M3X6-NI |
| Парткод: | X0-00430000 |
| Деталь: | BRKT-DH-380 |
| Парткод: | 6LE22881000 |
| Деталь: | THRMST-CS-7SA |
| Парткод: | 6LE71198000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | UAMS-05SN 142SH BLK |
| Парткод: | F0-01640000 |
| Деталь: | S/BID-M3X4-NI |
| Парткод: | X0-00426000 |
| Деталь: | STUD-HOOK-TRU |
| Парткод: | 6LE29029000 |
| Деталь: | BU28P-TZW-S (LF)(SN) |
| Парткод: | E0-09967000 |
| Деталь: | ASYS-BKT-SLD-R |
| Парткод: | 6LE25903000 |
| Деталь: | ASYS-PLATE-CRU-R |
| Парткод: | 6LE28232000 |
| Деталь: | ASYS-LINK-TBU-R |
| Парткод: | 6LE28228000 |
| Деталь: | ASYS-LINK-LIFT-CRU-R |
| Парткод: | 6LE28226000 |
| Деталь: | RAIL-GUIDE-TBU-R |
| Парткод: | 6LE28314000 |
| Деталь: | HLDR-TBU-R-CL |
| Парткод: | 6LE28284000 |
| Деталь: | HLDR-TBU-R-TR |
| Парткод: | 6LE28285000 |
| Деталь: | HLDR-RAIL-TBU |
| Парткод: | 6LE28419000 |
| Деталь: | BRKT-HLDR-TBU |
| Парткод: | 6LE28421000 |
| Деталь: | HOLDER-GUIDE-MID-L-R |
| Парткод: | 6LE28287000 |
| Деталь: | CAM-LIFT-TBU-R |
| Парткод: | 6LE28251000 |
| Деталь: | CAM-LIFT-CRU-R |
| Парткод: | 6LE28248000 |
| Деталь: | LINK-LIFT-PLATE-CRU |
| Парткод: | 6LE28294000 |
| Деталь: | SPG-HLDR-RAIL-TBU |
| Парткод: | 6LE28420000 |
| Деталь: | SPG-F-DPM-TBU-R |
| Парткод: | 6LE28339000 |
| Деталь: | WSHR-6R2X12XR5-APS |
| Парткод: | 6LE28372000 |
| Деталь: | ASYS-GEAR-6H24-BRG-N |
| Парткод: | 6LE22200000 |
| Деталь: | COUPL-DRIVE-DEV-MID |
| Парткод: | 6LE23715000 |
| Деталь: | ASYS-BASE-LSU-RER-RGT |
| Парткод: | 6LE26518000 |
| Деталь: | BRKT-REINF-FRM-R |
| Парткод: | 6LE25243000 |
| Деталь: | BASE-LSU-RER-LFT |
| Парткод: | 6LE26418000 |
| Деталь: | SPG-F-HLDR-LSU-LFT |
| Парткод: | 6LE26419000 |
| Деталь: | TERM-GUIDE-MID |
| Парткод: | 6LE29004000 |
| Деталь: | SPG-F-TERM-GUIDE |
| Парткод: | 6LE29003000 |
| Деталь: | ASYS-RESIST-380 |
| Парткод: | 6LE29002000 |
| Деталь: | ASYS-DUCT-EPU-COOL-TOP |
| Парткод: | 6LH32933000 |
| Деталь: | ASYS-DUCT-OZN |
| Парткод: | 6LH32907000 |
| Деталь: | DUCT-EXIT-REAR |
| Парткод: | 6LE23922000 |
| Деталь: | GEAR-4H66-10 |
| Парткод: | 6LE22159000 |
| Деталь: | ASYS-BRKT-DRV-TBU-FRT |
| Парткод: | 6LE22142000 |
| Деталь: | ASYS-DUCT-LSU-REAR |
| Парткод: | 6LE22588000 |
| Деталь: | S/PAN/WP-M3X5-NI |
| Парткод: | 6LA37949000 |
| Деталь: | DUCT-EPU-COOL-BTM-F45X |
| Парткод: | 6LH32912000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | LWS-1316Z |
| Парткод: | F0-01245000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | EDS-2323U |
| Парткод: | F0-00034000 |
| Деталь: | CS1A-B2CA |
| Парткод: | E0-01853000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | S/FHEXM-M3X8-NI |
| Парткод: | X0-02231000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | S/TPS/BID-3X6-ZU3 |
| Парткод: | X0-02069000 |
| Деталь: | S/TPP/FHEXM-4X8-NI |
| Парткод: | X0-02251000 |
| Деталь: | RFCC-525S |
| Парткод: | F0-01556000 |
| Деталь: | S/FHEXM-M4X6-NI |
| Парткод: | X0-02234000 |
| Деталь: | S/TPS/FHEXM-4X8-ZU3 |
| Парткод: | X0-02243000 |
| Деталь: | SCREW-LINK-M4 |
| Парткод: | 6LA65681000 |
| Деталь: | STOP-GUIDE-RTN-R |
| Парткод: | 6LE23910000 |
| Деталь: | GUIDE-EXIT-RTN-FC |
| Парткод: | 6LH36323000 |
| Деталь: | COVER-GUIDE-RTN-L-FC |
| Парткод: | 6LH36318000 |
| Деталь: | STOP-GUIDE-RTN-F |
| Парткод: | 6LE23912000 |
| Деталь: | SHAFT-GATE |
| Парткод: | 6LE23907000 |
| Деталь: | ROLL-GUIDE-RTN |
| Парткод: | 6LE23928000 |
| Деталь: | GATE-FUSER-SEN |
| Парткод: | 6LA36327000 |
| Деталь: | gate-fuser |
| Парткод: | 44202991000 |
| Деталь: | SPG-L-ACT-SEN |
| Парткод: | 6LE23908000 |
| Деталь: | SPG-C-4R46XR15X17R3 |
| Парткод: | 6LA36353000 |
| Деталь: | HRNS-EXITSW-380 |
| Парткод: | 6LE29350000 |
| Деталь: | SCREW-FUS-3X6P-380 |
| Парткод: | 6LE25982000 |
| Деталь: | GUIDE-EXIT-U-FC |
| Парткод: | 6LH36324000 |
| Деталь: | ASYS-BRKT-FUS-CLN |
| Парткод: | 6LH36226000 |
| Деталь: | COV-HAND-FUS-F |
| Парткод: | 6LE25929000 |
| Деталь: | COV-HAND-FUS-R |
| Парткод: | 6LE25930000 |
| Деталь: | ROLL-FUS-GUIDE |
| Парткод: | 6LE25931000 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 6LA08937000 |
| Деталь: | SHEET-FUS-R |
| Парткод: | 6LE25950000 |
| Деталь: | SHEET-FUS-F |
| Парткод: | 6LE25953000 |
| Деталь: | SHEET-FUS-OPEN |
| Парткод: | 6LE25954000 |
| Деталь: | SHEET-FUS-OPEN-F |
| Парткод: | 6LE25971000 |
| Деталь: | TLP1255(C8) |
| Парткод: | C0-10814000 |
| Деталь: | S/TPP/FHEXM-3X10-NI |
| Парткод: | X0-02248000 |
| Деталь: | S/PAN/SWWP-M3X10-NI |
| Парткод: | X0-00094000 |
| Деталь: | BRKT-DRV-TR1-CL-L |
| Парткод: | 6LE24349000 |
| Деталь: | GEAR-05S60-05H60-06 |
| Парткод: | 6LE22174000 |
| Деталь: | GEAR-05S40-05S64-06 |
| Парткод: | 6LE22168000 |
| Деталь: | GEAR-05S54-06 |
| Парткод: | 6LE22173000 |
| Деталь: | GEAR-05S50-8N |
| Парткод: | 6LE24365000 |
| Деталь: | GEAR-05S46-6N |
| Парткод: | 6LE24367000 |
| Деталь: | BRKT-DRV-TR1-CL |
| Парткод: | 6LE24355000 |
| Деталь: | ASYS-SHAFT-DRV-TR1-CLT |
| Парткод: | 6LE24358000 |
| Деталь: | CLUTCH-G28-08D-30A |
| Парткод: | 6LE40813000 |
| Деталь: | MOTRD-FEED-430 |
| Парткод: | 6LH09053000 |
| Деталь: | BUSH-8X12X8F-NU4 |
| Парткод: | 6LH23442000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | ASYB-MOTOR-RGST |
| Парткод: | 6LE29083000 |
| Деталь: | PLT-ARM-RGST |
| Парткод: | 6LE29048000 |
| Деталь: | GEAR-4H68-6 |
| Парткод: | 6LE29091000 |
| Деталь: | GEAR-4H94-CLT |
| Парткод: | 6LE29090000 |
| Деталь: | ASYS-SHAFT-DRV-RGST |
| Парткод: | 6LE29079000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | PLT-ARM-RGST-DRV |
| Парткод: | 6LE29094000 |
| Деталь: | GEAR-8S40-4H68-6 |
| Парткод: | 6LE29089000 |
| Деталь: | GEAR-10S17_10S31-6 |
| Парткод: | 6LE29052000 |
| Деталь: | GEAR-10S16_8S27-6 |
| Парткод: | 6LE29051000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | GEAR-4H72-6 |
| Парткод: | 6LE29092000 |
| Деталь: | STUD-PLANET-GEAR |
| Парткод: | 6LE24255000 |
| Деталь: | GEAR-05S56-08 |
| Парткод: | 6LE24357000 |
| Деталь: | BRKT-PLANET-GEAR |
| Парткод: | 6LE24239000 |
| Деталь: | COLLAR-ROLL-MID-380 |
| Парткод: | 6LE24356000 |
| Деталь: | GEAR-10S29-05S58-06 |
| Парткод: | 6LE22175000 |
| Деталь: | MSB-1207 |
| Парткод: | F0-01250000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/TPS/FHEXM-4X8-ZU3 |
| Парткод: | X0-02243000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | LNR-1680HHRP0P15LY13 |
| Парткод: | F0-01390000 |
| Деталь: | TR-BLT-FC28 |
| Парткод: | 6LH49407000 |
| Деталь: | TR-BLT-CLN-FC35 |
| Парткод: | 6LE39013000 |
| Деталь: | EPU-FC28-K |
| Парткод: | 6LH49403000 |
| Деталь: | EPU-FC28-Y |
| Парткод: | 6LH49403100 |
| Деталь: | EPU-FC28-M |
| Парткод: | 6LH49403200 |
| Деталь: | EPU-FC28-C |
| Парткод: | 6LH49403300 |
| Деталь: | FUSER-FC28-115 |
| Парткод: | 6LH49400000 |
| Деталь: | FUSER-FC28-220 |
| Парткод: | 6LH49400100 |
| Деталь: | FUSER-FC45-115 |
| Парткод: | 6LH49401000 |
| Деталь: | FUSER-FC45-220 |
| Парткод: | 6LH49401100 |
| Деталь: | ASYS-ROLL-SPT-L30 |
| Парткод: | 6LA28899000 |
| Деталь: | ARBOR-SPT-BYP |
| Парткод: | 6LA28863000 |
| Деталь: | SPR-1.0-15.65-13L |
| Парткод: | 6LA28865000 |
| Деталь: | SHAFT-ROL-SPT |
| Парткод: | 6LE40437000 |
| Деталь: | LEVER-SPT-F |
| Парткод: | 6LA28921000 |
| Деталь: | LEVER-SPT-R |
| Парткод: | 6LA28922000 |
| Деталь: | SPG-E-6XR6X91R7R |
| Парткод: | 6LA28840000 |
| Деталь: | STAY-SPT-BYP-350 |
| Парткод: | 6LE21222000 |
| Деталь: | BUSH-8X12X8F-NU4 |
| Парткод: | 6LH23442000 |
| Деталь: | ASYS-BRKT-LVR-SPT |
| Парткод: | 6LA28857000 |
| Деталь: | COVER-SPE-ARBOR-17 |
| Парткод: | 6LA28861000 |
| Деталь: | HOLDER-ROL-SPT-BYP |
| Парткод: | 6LA28862000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | ASYS-SHAFT-DRV-BYP |
| Парткод: | 6LE21236000 |
| Деталь: | PLATE-DRIVE-BYP |
| Парткод: | 6LE21213000 |
| Деталь: | ASYS-PLATE-BYP-F380 |
| Парткод: | 6LE24310000 |
| Деталь: | GEAR-10S23-6 |
| Парткод: | 6LE21215000 |
| Деталь: | BRKT-DRV-BYP-F380 |
| Парткод: | 6LE21210000 |
| Деталь: | CLUTCH-G28-08D-30A |
| Парткод: | 6LE40813000 |
| Деталь: | BRKT-DRIVE-BYP-RER |
| Парткод: | 6LE21235000 |
| Деталь: | CPG-DRV-BYP-350 |
| Парткод: | 6LA28915000 |
| Деталь: | STUD-DRV-BYP-F380 |
| Парткод: | 6LE21209000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | S/TPS/FHEXM/R-3X8-ZU3 |
| Парткод: | X0-02420000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | JIG-SW-F-COV |
| Парткод: | 4407915730 |
| Деталь: | BRUSH-33 |
| Парткод: | 4407915710 |
| Деталь: | JIG-CLEAN-DOC |
| Парткод: | 4406552140 |
| Деталь: | HOLDER-WIRE-SCAN |
| Парткод: | 6LA01757000 |
| Деталь: | NOZZLE-BOTTLE |
| Парткод: | 4407914000 |
| Деталь: | ASYB-JIG-GAP-DOC-SL-380 |
| Парткод: | 6LE23720000 |
| Деталь: | SPE-MOT-TNS |
| Парткод: | 44202661000 |
| Деталь: | JIG-FUS-SEP |
| Парткод: | 6LE25969000 |
| Деталь: | BAG-DRUM |
| Парткод: | 4408600920 |
| Деталь: | OIL-LAUNA40-100 |
| Парткод: | 4842512170 |
| Деталь: | ASM-PG-ALV2 |
| Парткод: | 41303711000 |
| Деталь: | MOLYKOTE_EM-30L_100G |
| Парткод: | 6LE36904000 |
| Деталь: | ASM-PG-HP300-S |
| Парткод: | 41303709000 |
| Деталь: | GREASE-HP300-S |
| Парткод: | 6LA00019000 |
| Деталь: | BELT-TBU-F450 |
| Парткод: | 6LH38612000 |
| Деталь: | GEAR-CLN-DRV-RLR |
| Парткод: | 6LE28271000 |
| Деталь: | GUIDE-RIB-YF20 |
| Парткод: | 6LE28513000 |
| Деталь: | HLDR-BRG-TNS |
| Парткод: | 6LE28281000 |
| Деталь: | RLR-DRV-TBU-EPDM-450 |
| Парткод: | 6LH38621000 |
| Деталь: | RLR-LIFT-TBU-N |
| Парткод: | 6LE28519000 |
| Деталь: | RLR-SNS-TBU-N |
| Парткод: | 6LE28518000 |
| Деталь: | RLR-TNS-TBU-NA |
| Парткод: | 6LH38611000 |
| Деталь: | RLR-TR1-TBU |
| Парткод: | 6LE28319000 |
| Деталь: | ASYS-RLR-TR2-TBU-FCOAT |
| Парткод: | 6LH38608000 |
| Деталь: | SPG-T-LIFT-TNS-F |
| Парткод: | 6LE28472000 |
| Деталь: | SPG-T-LIFT-TNS-R |
| Парткод: | 6LE28473000 |
| Деталь: | COLAR-RLR-TBU-12-N |
| Парткод: | 6LE28537000 |
| Деталь: | COLAR-RLR-TBU-12L-N |
| Парткод: | 6LE28538000 |
| Деталь: | DDL-1260ZZHP0P25LY13 |
| Парткод: | F0-01371000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | ASYS-SNR-BASE-IMG-POS |
| Парткод: | 6LE22854000 |
| Деталь: | SHUT-PL-IMG-POS |
| Парткод: | 6LE22805000 |
| Деталь: | LINK-IMG-POS |
| Парткод: | 6LE22804000 |
| Деталь: | SNSR-POS-380 |
| Парткод: | 6LE29453000 |
| Деталь: | SNSR-CTD-380 |
| Парткод: | 6LE29754000 |
| Деталь: | SND-TDS-10A-380 |
| Парткод: | 6LE22859000 |
| Деталь: | SPG-E-4R5XR3X20R8 |
| Парткод: | 6LE22846000 |
| Деталь: | HRNS-CTD-380 |
| Парткод: | 6LE29383000 |
| Деталь: | ASYS-SHAFT-CAM-TRU |
| Парткод: | 6LE29082000 |
| Деталь: | CAM-TRU |
| Парткод: | 6LE29010000 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | GEAR-08S21-TR2-S2 |
| Парткод: | 6LE46431000 |
| Деталь: | ACTR-CAM-TRU |
| Парткод: | 6LE29012000 |
| Деталь: | ASYS-HLDR-P-POWDER-L |
| Парткод: | 6LE24324000 |
| Деталь: | GEAR-10S26-CLT |
| Парткод: | 6LE29057000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | S/PAN-M3X6-ZU3 |
| Парткод: | X0-02256000 |
| Деталь: | S/BID-M3X6-NI |
| Парткод: | X0-00430000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | P/PRL/BH7-2X14-SS |
| Парткод: | X0-00990000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/TPP/FHEXM-4X8-NI |
| Парткод: | X0-02251000 |
| Деталь: | REF-LAMP-430 |
| Парткод: | 6LH08210000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | LAMP-EXPO-450 |
| Парткод: | 6LH39789000 |
| Деталь: | INV-EXPO-450 |
| Парткод: | 6LH39788000 |
| Деталь: | COVER-INV |
| Парткод: | 6LA39548000 |
| Деталь: | S/TPP/BRZ-3X6-ZU3 |
| Парткод: | X0-02541000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | FOOT-CRG-410 |
| Парткод: | 6LE46323000 |
| Деталь: | UAMS-05-2 |
| Парткод: | F0-00044000 |
| Деталь: | HRNS-SCN-INV-450 |
| Парткод: | 6LH39808000 |
| Деталь: | GUIDE-HRNS-CRG1 |
| Парткод: | 6LA39572000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | MYLAR-HRNS-INV |
| Парткод: | 6LA39577000 |
| Деталь: | CARRIGE-1-450 |
| Парткод: | 6LH37858000 |
| Деталь: | None |
| Парткод: | 6LH32100000 |
| Деталь: | None |
| Парткод: | 6LE22838000 |
| Деталь: | None |
| Парткод: | 6LE21715000 |
| Деталь: | None |
| Парткод: | 6LH32103000 |
| Деталь: | None |
| Парткод: | 6LH32104000 |
| Деталь: | None |
| Парткод: | 6LH32102000 |
| Деталь: | None |
| Парткод: | 6LE21704000 |
| Деталь: | None |
| Парткод: | 6LH32111000 |
| Деталь: | None |
| Парткод: | 6LE21709000 |
| Деталь: | None |
| Парткод: | 6LE21703000 |
| Деталь: | None |
| Парткод: | 6LE21708000 |
| Деталь: | None |
| Парткод: | 6LH32121000 |
| Деталь: | None |
| Парткод: | 6LH32914000 |
| Деталь: | None |
| Парткод: | 6LH32128000 |
| Деталь: | None |
| Парткод: | 6LH32124000 |
| Деталь: | None |
| Парткод: | 6LE21700000 |
| Деталь: | None |
| Парткод: | 6LA29536000 |
| Деталь: | None |
| Парткод: | 6LH32101000 |
| Деталь: | None |
| Парткод: | 6LE21763000 |
| Деталь: | None |
| Парткод: | 6LE21751000 |
| Деталь: | None |
| Парткод: | 6LE21710000 |
| Деталь: | None |
| Парткод: | 6LE21759000 |
| Деталь: | None |
| Парткод: | 6LH32130000 |
| Деталь: | None |
| Парткод: | 6LE21719000 |
| Деталь: | None |
| Парткод: | 6LE21725000 |
| Деталь: | None |
| Парткод: | 6LE21736000 |
| Деталь: | None |
| Парткод: | 6LE21742000 |
| Деталь: | None |
| Парткод: | 6LA29555000 |
| Деталь: | None |
| Парткод: | 6LE25955000 |
| Деталь: | None |
| Парткод: | 6LE21756000 |
| Деталь: | None |
| Парткод: | 6LE27462000 |
| Деталь: | None |
| Парткод: | 6LA47644000 |
| Деталь: | None |
| Парткод: | 44204604000 |
| Деталь: | None |
| Парткод: | 6LH39270000 |
| Деталь: | None |
| Парткод: | 6LH39271000 |
| Деталь: | None |
| Парткод: | F0-01564000 |
| Деталь: | None |
| Парткод: | X0-02247000 |
| Деталь: | None |
| Парткод: | X0-02249000 |
| Деталь: | None |
| Парткод: | X0-02235000 |
| Деталь: | None |
| Парткод: | X0-02421000 |
| Деталь: | None |
| Парткод: | 6LH32110000 |
| Деталь: | None |
| Парткод: | 6LH32110100 |
| Деталь: | None |
| Парткод: | 6LH32110200 |
| Деталь: | None |
| Парткод: | 6LH32110300 |
| Деталь: | None |
| Парткод: | 6LH32110400 |
| Деталь: | CASE-CST |
| Парткод: | 6LA56960000 |
| Деталь: | K-SFT-LIFT-TRAY |
| Парткод: | 41304004000 |
| Деталь: | BUSH-SFT-LIFT |
| Парткод: | 41306028000 |
| Деталь: | LEVER-LIFT-TRAY |
| Парткод: | 6LA60307000 |
| Деталь: | CUSH-LVR-LIFT |
| Парткод: | 41306614000 |
| Деталь: | ASY-TRAY-CST-AT/DM |
| Парткод: | 6LA56688000 |
| Деталь: | CUSH-TRAY-CST |
| Парткод: | 41306517000 |
| Деталь: | WALL-SIDE-F-AT/DM |
| Парткод: | 6LA56692200 |
| Деталь: | LVR-ADJUST-WALL |
| Парткод: | 6LA56693200 |
| Деталь: | SPACER-RACK-CST |
| Парткод: | 6LA56707000 |
| Деталь: | PLATE-RACK-CST |
| Парткод: | 6LA56706200 |
| Деталь: | K-WALL-SIDE-R |
| Парткод: | 6LA56703200 |
| Деталь: | LEVER-LOCK-WALL-RER |
| Парткод: | 6LA29058000 |
| Деталь: | LOCK-WALL-R |
| Парткод: | 41306260000 |
| Деталь: | SPL-LOCK-WALL-R |
| Парткод: | 41305546000 |
| Деталь: | WALL-CSSTT-END |
| Парткод: | 6LA29061000 |
| Деталь: | COV-CSSTT-450-D |
| Парткод: | 6LH32105000 |
| Деталь: | COV-CSSTT-HNDL-450 |
| Парткод: | 6LH32106000 |
| Деталь: | ASYS-PL-PINION-TRY |
| Парткод: | 6LA56961000 |
| Деталь: | SPC-LVR-WALL-F |
| Парткод: | 6LA56695000 |
| Деталь: | LBL/O-P-MAX |
| Парткод: | 41307701000 |
| Деталь: | LBL_O-PAPER-2 |
| Парткод: | 6LE40703000 |
| Деталь: | LBL_O-GUIDE-2 |
| Парткод: | 6LE40701000 |
| Деталь: | LBL_O-GUIDE-CONP-450 |
| Парткод: | 6LH31902000 |
| Деталь: | SHEET-CST |
| Парткод: | 41307599000 |
| Деталь: | LBL_O-LD-2 |
| Парткод: | 6LE40700000 |
| Деталь: | MYLAR-CST-BK |
| Парткод: | 6LA60306000 |
| Деталь: | S/TPP/BRZ-3X6-ZU3 |
| Парткод: | X0-02541000 |
| Деталь: | S/BID-M3X8-NI |
| Парткод: | X0-00434000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/TPP/BID-3X8-NI |
| Парткод: | X0-01989000 |
| Деталь: | W/TH/A-3-SS |
| Парткод: | X0-02116000 |
| Деталь: | S/TPP/BID-3X6-NC |
| Парткод: | X0-01414000 |
| Деталь: | SIZE-CST-450-LT |
| Парткод: | 6LH31900100 |
| Деталь: | SIZE-CST-450-A4 |
| Парткод: | 6LH31900000 |
| Деталь: | BRKT-SEN-FUS |
| Парткод: | 6LE25874000 |
| Деталь: | BASE-SEN-FC |
| Парткод: | 6LH36313000 |
| Деталь: | HLDER-SEN-FC |
| Парткод: | 6LH36327000 |
| Деталь: | SNR-THRMO-380 |
| Парткод: | 6LE29449000 |
| Деталь: | S/PAN/SWWP-M3X14-NI |
| Парткод: | X0-02135000 |
| Деталь: | BRUSH-EXIT-380 |
| Парткод: | 6LE23956000 |
| Деталь: | GUIDE-STAY-FUS-FC |
| Парткод: | 6LH36326000 |
| Деталь: | STAY-DUCT-FUS |
| Парткод: | 6LH36296000 |
| Деталь: | HRNS-LVPS-FSR2-450 |
| Парткод: | 6LH39728000 |
| Деталь: | SPC068-080-160 |
| Парткод: | 6LA14468000 |
| Деталь: | HRNS-THM-450 |
| Парткод: | 6LH40055000 |
| Деталь: | SCREW-D4-18-M3 |
| Парткод: | 4406326040 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 6LA08937000 |
| Деталь: | ASYS-ROLL-EXIT-U |
| Парткод: | 6LE23919000 |
| Деталь: | DUCT-EXIT-COVER |
| Парткод: | 6LE23921000 |
| Деталь: | DUCT-EXIT-BASE-FC |
| Парткод: | 6LH36321000 |
| Деталь: | GUIDE-EXIT |
| Парткод: | 6LE23924000 |
| Деталь: | SHAFT-EXIT-L |
| Парткод: | 6LE23925000 |
| Деталь: | GEAR-10S24-EXIT |
| Парткод: | 6LE23943000 |
| Деталь: | ROLL-EXIT-L-380 |
| Парткод: | 6LE23952000 |
| Деталь: | SPL-EXIT-ROLL-K |
| Парткод: | 6LE23957000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | LBL-HOT-410 |
| Парткод: | 6LE45619000 |
| Деталь: | BRKT-FUS-VOLT-06 |
| Парткод: | 6LH36304000 |
| Деталь: | BRKT-STAY-DRW-450 |
| Парткод: | 6LH36253000 |
| Деталь: | BRKT-STAY-DRW-454 |
| Парткод: | 6LH36203000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | S/BID-M3X6-NI |
| Парткод: | X0-00430000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | LF-1260ZZ |
| Парткод: | F0-00781000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | ASYS-FRM-FUS-450 |
| Парткод: | 6LH36283000 |
| Деталь: | ASYS-SEP-AJ6-7A |
| Парткод: | 6LH36336000 |
| Деталь: | BT-FC35-FU |
| Парткод: | 6LE94751000 |
| Деталь: | FR-FC28-U |
| Парткод: | 6LE98369000 |
| Деталь: | BRKT-FUS-SEN-IN-45X |
| Парткод: | 6LH36299000 |
| Деталь: | BRKT-THRM-LAMP-454 |
| Парткод: | 6LH36229000 |
| Деталь: | BRKT-HR-TMS |
| Парткод: | 6LE25887000 |
| Деталь: | SPG-E-FUS-SEN-45X |
| Парткод: | 6LH36262000 |
| Деталь: | BRKT-LAMP-F-454T |
| Парткод: | 6LH36201000 |
| Деталь: | ROLL-HT |
| Парткод: | 6LE25800000 |
| Деталь: | BRKT-TEN-SP |
| Парткод: | 6LE25809000 |
| Деталь: | COLLAR-HR-T1 |
| Парткод: | 6LE25801000 |
| Деталь: | CRR-HR-CLR-K2 |
| Парткод: | 6LE25846000 |
| Деталь: | COV-HNS-R-45X |
| Парткод: | 6LH36308000 |
| Деталь: | STUD-TEN-SP |
| Парткод: | 6LE25834000 |
| Деталь: | BUSH-FUS-FR |
| Парткод: | 6LE25822000 |
| Деталь: | SPG-E-FUS-HR |
| Парткод: | 6LE25853000 |
| Деталь: | SCREW-CON-DEV-V |
| Парткод: | 6LA08933000 |
| Деталь: | THRMST-HTR1-380 |
| Парткод: | 6LE29439000 |
| Деталь: | THRMST-HTR2-380 |
| Парткод: | 6LE29440000 |
| Деталь: | THMS-FUS-BELT-E-450 |
| Парткод: | 6LH39783000 |
| Деталь: | HRNS-FUS-HTR-C-380 |
| Парткод: | 6LE29346000 |
| Деталь: | COVER-FUS-F-FC |
| Парткод: | 6LH36316000 |
| Деталь: | COVER-FUS-B-FC |
| Парткод: | 6LH36315000 |
| Деталь: | COVER-FUS-R-FC |
| Парткод: | 6LH36317000 |
| Деталь: | BRKT-LAMP-R-454T |
| Парткод: | 6LH36202000 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 6LA08937000 |
| Деталь: | COV-FUS-HNS-R-FC |
| Парткод: | 6LH36314000 |
| Деталь: | LAMP-TRIPLE-115-454 |
| Парткод: | 6LH36249000 |
| Деталь: | LAMP-TRIPLE-230-454 |
| Парткод: | 6LH36250000 |
| Деталь: | LAMP-C-115-K2 |
| Парткод: | 6LE25860000 |
| Деталь: | LAMP-C-230-K2 |
| Парткод: | 6LE25863000 |
| Деталь: | LAMP-S-115-K2 |
| Парткод: | 6LE25861000 |
| Деталь: | LAMP-S-230-K2 |
| Парткод: | 6LE25864000 |
| Деталь: | HRNS-DRW1-AC-450 |
| Парткод: | 6LH39776000 |
| Деталь: | HRNS-DRW1B-AC-450 |
| Парткод: | 6LH39777000 |
| Деталь: | HRNS-DRW2-AC-450 |
| Парткод: | 6LH39706000 |
| Деталь: | HRNS-DRW2B-AC-450 |
| Парткод: | 6LH39801000 |
| Деталь: | COVER-INFRT-380D |
| Парткод: | 6LE28719000 |
| Деталь: | PLATE-MG |
| Парткод: | 6LE21710000 |
| Деталь: | KEY-EUDJ-F380 |
| Парткод: | 6LE28727000 |
| Деталь: | SEAL-COVIN-380 |
| Парткод: | 6LE28816000 |
| Деталь: | ASYS-DUCT-TBU-F45X |
| Парткод: | 6LH39241000 |
| Деталь: | ASYS-SHUT-UTNR |
| Парткод: | 6LE28754000 |
| Деталь: | SPG-C-SHUT-TNR-CR |
| Парткод: | 6LE28738000 |
| Деталь: | DUCT-TNR-UPR-450 |
| Парткод: | 6LH32938000 |
| Деталь: | DUCT-TNR-LWR-450 |
| Парткод: | 6LH32939000 |
| Деталь: | COVER-INNR-BLIND-F45X |
| Парткод: | 6LH39101000 |
| Деталь: | S/TPP/BID-4X8-NI |
| Парткод: | X0-01922000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | BRKT-DH-EXIT-380 |
| Парткод: | 6LE22882000 |
| Деталь: | THRMST-CS-7SA |
| Парткод: | 6LE71198000 |
| Деталь: | HRNS-DHT-EXIT-450 |
| Парткод: | 6LH39868000 |
| Деталь: | HF05N442 |
| Парткод: | E0-10981000 |
| Деталь: | HF05N132 |
| Парткод: | E0-10980000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | EDS-0607M |
| Парткод: | F0-00671000 |
| Деталь: | UAMS-05SN 142SH BLK |
| Парткод: | F0-01640000 |
| Деталь: | S/TPS/BID-3X6-ZU3 |
| Парткод: | X0-02069000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | COV-CONP-UPR-45XNP |
| Парткод: | 6LH37303100 |
| Деталь: | COV-CONP-LWR-45X |
| Парткод: | 6LH37304000 |
| Деталь: | COV-CONP-CLEAR-45X |
| Парткод: | 6LH37305000 |
| Деталь: | KEY-START |
| Парткод: | 6LH02005000 |
| Деталь: | KEY-START-RING |
| Парткод: | 6LH02006000 |
| Деталь: | KEY-STOP |
| Парткод: | 6LH02007000 |
| Деталь: | KEY-RESET-U |
| Парткод: | 6LH02008100 |
| Деталь: | KEY-FUNCTION |
| Парткод: | 6LH02009000 |
| Деталь: | KEY-MENU |
| Парткод: | 6LH02010000 |
| Деталь: | KEY-POWER |
| Парткод: | 6LH02011000 |
| Деталь: | KEY-TEN-45X |
| Парткод: | 6LH37308000 |
| Деталь: | KEY-ENERGY-45X |
| Парткод: | 6LH37306000 |
| Деталь: | KEY-USER-FUNC-45X |
| Парткод: | 6LH37307000 |
| Деталь: | LID-LED-45X |
| Парткод: | 6LH37309000 |
| Деталь: | KEY-COUNT |
| Парткод: | 6LH02012000 |
| Деталь: | MYLAR-SHIELD-45X |
| Парткод: | 6LH37310000 |
| Деталь: | SHIELD-SHEET-45X |
| Парткод: | 6LH37311000 |
| Деталь: | SHIELD-CONPANE-45X |
| Парткод: | 6LH37312000 |
| Деталь: | ASYS-HINGE-R-45X |
| Парткод: | 6LH37313000 |
| Деталь: | ASYS-HINGE-L-380 |
| Парткод: | 6LE26904000 |
| Деталь: | SHEET-PANEL-45X-U |
| Парткод: | 6LH37331000 |
| Деталь: | ASYS-PNL-TOUCH-450 |
| Парткод: | 6LH37325000 |
| Деталь: | ASYS-DSP-LCD-450 |
| Парткод: | 6LH37326000 |
| Деталь: | PWA-F-DSP-450 |
| Парткод: | 6LH39823000 |
| Деталь: | PWA-F-KEY-450 |
| Парткод: | 6LH39824000 |
| Деталь: | INV-DSP-450 |
| Парткод: | 6LH39802000 |
| Деталь: | HRNS-LCD-DSP-450 |
| Парткод: | 6LH40016000 |
| Деталь: | HRNS-INV-DSP-450 |
| Парткод: | 6LH39826000 |
| Деталь: | HRNS-SYS-DSP-450 |
| Парткод: | 6LH39827000 |
| Деталь: | S/TPB/BID-2X6-NI |
| Парткод: | X0-02094000 |
| Деталь: | S/TPP/BRZ-3X8-NI |
| Парткод: | X0-02096000 |
| Деталь: | S/TPP/BRZ-3X10-NI |
| Парткод: | X0-02095000 |
| Деталь: | S/BID-M3X8-NI |
| Парткод: | X0-00434000 |
| Деталь: | S/PAN/SWWP-M4X8-ZU3 |
| Парткод: | X0-02217000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | STOPPER-OPE-45X |
| Парткод: | 6LH37319000 |
| Деталь: | ASYS-GLASS-ADF-350 |
| Парткод: | 6LA39804000 |
| Деталь: | SPL-GLASS-ADF |
| Парткод: | 6LA39841000 |
| Деталь: | MYLAR-TAPE-FRT |
| Парткод: | 6LA39843000 |
| Деталь: | SEAL-COLOR-TP-L-R2 |
| Парткод: | 6LA39889000 |
| Деталь: | SHEET-GEL-13-4 |
| Парткод: | 6LA39375000 |
| Деталь: | MYLAR-SPL-GLASS-ADF |
| Парткод: | 6LA39842000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | ASYS-GLASS-380A |
| Парткод: | 6LE27406000 |
| Деталь: | ASYS-GLASS-380L |
| Парткод: | 6LE27406100 |
| Деталь: | ASYS-BRKT-MOTR-DEV |
| Парткод: | 6LE22169000 |
| Деталь: | MOTR_D-DEV-380 |
| Парткод: | 6LE22172000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | RNR-1560ZZRP0P24LY121 |
| Парткод: | F0-01482000 |
| Деталь: | SHAFT-DRIVE-DEV |
| Парткод: | 6LE22158000 |
| Деталь: | GEAR-5H77-8-ONEWAY |
| Парткод: | 6LE22161000 |
| Деталь: | STOP RING |
| Парткод: | 41306265000 |
| Деталь: | GEAR-5H77_5H70-6 |
| Парткод: | 6LE22162000 |
| Деталь: | GEAR-5H70-8-ONEWAY |
| Парткод: | 6LE22163000 |
| Деталь: | ASYS-BRKT-DRIVE-DEV-RER |
| Парткод: | 6LE22152000 |
| Деталь: | ASYS-BRKT-DRIVE-TBU-RER |
| Парткод: | 6LE22145000 |
| Деталь: | GEAR-4H94-8N |
| Парткод: | 6LE22201000 |
| Деталь: | MOTR_S-TBU-380 |
| Парткод: | 6LE22196000 |
| Деталь: | GEAR-4H164-8N |
| Парткод: | 6LE22202000 |
| Деталь: | GEAR-4H78-6H36-8N |
| Парткод: | 6LE22203000 |
| Деталь: | BRKT-DRIVE-DEV-FRT |
| Парткод: | 6LE22151000 |
| Деталь: | GEAR-5H59-4H62-8 |
| Парткод: | 6LE22149000 |
| Деталь: | GEAR-5H62_5H29-8 |
| Парткод: | 6LE22190000 |
| Деталь: | PLATE-DRIVE-TBU |
| Парткод: | 6LE22147000 |
| Деталь: | S/BID-M3X4-ZC3-RED |
| Парткод: | 6LE22138000 |
| Деталь: | SPG-E-DRV-TBU |
| Парткод: | 6LE22148000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | LNR-1680HHRP0P15LY13 |
| Парткод: | F0-01390000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | S/BID-M3X4-NI |
| Парткод: | X0-00426000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/TPS/FHEXM-4X8-ZU3 |
| Парткод: | X0-02243000 |
| Деталь: | ASYS-GUIDE-L |
| Парткод: | 6LE29087000 |
| Деталь: | GUIDE-MID-R |
| Парткод: | 6LE29006000 |
| Деталь: | ASYS-GUIDE-RGST-L-380 |
| Парткод: | 6LE24275000 |
| Деталь: | ACTR-RGST-380 |
| Парткод: | 6LE24231000 |
| Деталь: | ACTR-MID-380 |
| Парткод: | 6LE24229000 |
| Деталь: | HLDR-REG-SENSOR |
| Парткод: | 6LA37626000 |
| Деталь: | BRKT-SENS-MID |
| Парткод: | 6LE24232000 |
| Деталь: | SPG-ACT-380 |
| Парткод: | 6LE24277000 |
| Деталь: | MYLAR-SW-RGST-2 |
| Парткод: | 44201543000 |
| Деталь: | HRNS-FEED1-380 |
| Парткод: | 6LE29386000 |
| Деталь: | SCREW-LOCK-ARM |
| Парткод: | 6LA37669000 |
| Деталь: | HLDR-ROL-RGST-F-AL |
| Парткод: | 6LE24326000 |
| Деталь: | HLDR-ROL-RGST-R-AL |
| Парткод: | 6LE24327000 |
| Деталь: | STOP RING |
| Парткод: | 41306265000 |
| Деталь: | RLR-MID-380 |
| Парткод: | 6LE24374000 |
| Деталь: | GEAR-05S40-8N |
| Парткод: | 6LE24366000 |
| Деталь: | BUSH-ROL-RGST-L |
| Парткод: | 6LE24328000 |
| Деталь: | BUSH-8X12X8F-NU4 |
| Парткод: | 6LH23442000 |
| Деталь: | ROLLER-RGST-L |
| Парткод: | 6LE24201000 |
| Деталь: | GEAR-0.8-25 |
| Парткод: | 4407547320 |
| Деталь: | GUIDE-RAIL-WIRE-F |
| Парткод: | 6LE24337000 |
| Деталь: | GUIDE-RAIL-WIRE-R |
| Парткод: | 6LE24338000 |
| Деталь: | CAM-RGST-STOP-F |
| Парткод: | 6LE24335000 |
| Деталь: | CAM-RGST-STOP-R |
| Парткод: | 6LE24336000 |
| Деталь: | WIRE-CAM-RGST |
| Парткод: | 6LE24339000 |
| Деталь: | SPG-E-CAM-RGST |
| Парткод: | 6LE24340000 |
| Деталь: | LBL-GUIDE-MID |
| Парткод: | 6LE29099000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | S/TPP/BID-3X8-NI |
| Парткод: | X0-01989000 |
| Деталь: | S/TPS/FHEXM-4X8-ZU3 |
| Парткод: | X0-02243000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | BASE-SOCKET-TBU |
| Парткод: | 6LE28235000 |
| Деталь: | BRKT-SOCKET-TBU |
| Парткод: | 6LE28243000 |
| Деталь: | COVER-SOCKET-TBU |
| Парткод: | 6LE28257000 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 6LA08937000 |
| Деталь: | HRNS-HVPS-TBU-450 |
| Парткод: | 6LH39745000 |
| Деталь: | SPG-BIAS-TBU |
| Парткод: | 6LE28332000 |
| Деталь: | ASYS-SHAFT-LIFT-CRU |
| Парткод: | 6LE28233000 |
| Деталь: | BRKT-CLICK-CRU |
| Парткод: | 6LE28239000 |
| Деталь: | BRKT-CLICK-SHAFT-VA |
| Парткод: | 6LE28385000 |
| Деталь: | COLAR-CLICK |
| Парткод: | 6LE28256000 |
| Деталь: | SPG-T-CLICK |
| Парткод: | 6LE28427000 |
| Деталь: | WASHER-81403 |
| Парткод: | 4407010320 |
| Деталь: | CASE-TERMINAL-TR1-FN |
| Парткод: | 6LE28502000 |
| Деталь: | COVER-TERMINAL-TR1-FN |
| Парткод: | 6LE28500000 |
| Деталь: | SCREW-LVR-CRU |
| Парткод: | 6LE28464000 |
| Деталь: | CASE-TERMINAL-TR1-RN |
| Парткод: | 6LE28501000 |
| Деталь: | COVER-TERMINAL-TR1-RN |
| Парткод: | 6LE28499000 |
| Деталь: | PLATE-TR1 |
| Парткод: | 6LE28310000 |
| Деталь: | HLDR-TR-ROLL |
| Парткод: | 4406537280 |
| Деталь: | SPG-C-TR1 |
| Парткод: | 6LE28334000 |
| Деталь: | HANDL-LIFT-TBU-CRU |
| Парткод: | 6LE28460000 |
| Деталь: | S/TPP/BID-3X6-NC |
| Парткод: | X0-01414000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | LES-1010 |
| Парткод: | F0-00542000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | S/PAN/SWWP-M4X8-ZU3 |
| Парткод: | X0-02217000 |
| Деталь: | RLWC-2SV0 |
| Парткод: | F0-01609000 |
| Деталь: | DEV-KIT-FC28K |
| Парткод: | 6LH49404000 |
| Деталь: | DEV-KIT-FC28CLR |
| Парткод: | 6LH49405000 |
| Деталь: | TBU-KIT-FC28 |
| Парткод: | 6LH49406000 |
| Деталь: | FR-KIT-FC28 |
| Парткод: | 6LH49408000 |
| Деталь: | ROL-KIT-16CST |
| Парткод: | 41303640000 |
| Деталь: | COVER-INNR-DRW-45X |
| Парткод: | 6LH39105000 |
| Деталь: | HRNS-EPU-450 |
| Парткод: | 6LH39710000 |
| Деталь: | S/TPS/FHEXM/R-4X8-ZU3 |
| Парткод: | X0-02421000 |
| Деталь: | ASYS-CASE-DUCT-TOP |
| Парткод: | 6LH39112000 |
| Деталь: | CASE-DUCT-AUG-WTNR |
| Парткод: | 6LH39118000 |
| Деталь: | ASYS-BUSH-6X12X6F-M |
| Парткод: | 6LH04280000 |
| Деталь: | COUPL-AUG-WTNR |
| Парткод: | 6LH39119000 |
| Деталь: | CLNR-WTNR-DUCT-2 |
| Парткод: | 6LH39120000 |
| Деталь: | AUGER-WTNR-FRT |
| Парткод: | 6LH39111000 |
| Деталь: | BUSH-061206F-M |
| Парткод: | 44204339000 |
| Деталь: | PULLY-2GT19-6 |
| Парткод: | 6LH39128000 |
| Деталь: | ASYS-LID-WTNR |
| Парткод: | 6LH39215000 |
| Деталь: | ASYS-GEAR-PLT |
| Парткод: | 6LH39201000 |
| Деталь: | ASYS-WPIPE-45X |
| Парткод: | 6LH39205000 |
| Деталь: | GEAR-10S33-6D |
| Парткод: | 6LH39212000 |
| Деталь: | GEAR-10S33-P2GT19-6 |
| Парткод: | 6LH39213000 |
| Деталь: | BLT_SY-176-2GT-2 |
| Парткод: | 6LH39214000 |
| Деталь: | ASYS-SHUT-WTNR |
| Парткод: | 6LH39125000 |
| Деталь: | SPG-E-SHUT-WTNR |
| Парткод: | 6LH39123000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | ACTR-U-PADL-SNR |
| Парткод: | 6LE28832000 |
| Деталь: | LID-DUCT-F45X |
| Парткод: | 6LH39211000 |
| Деталь: | AUGER-WTNR-F45X |
| Парткод: | 6LH39209000 |
| Деталь: | DUCT-VT-F45X |
| Парткод: | 6LH39210000 |
| Деталь: | HRNS-AUGLCK-450 |
| Парткод: | 6LH39798000 |
| Деталь: | CS1A-B2CA |
| Парткод: | E0-01853000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | S/TPP/BID-3X8-NI |
| Парткод: | X0-01989000 |
| Деталь: | ACTR-COV-OPEN |
| Парткод: | 6LH39217000 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 6LA08937000 |
| Деталь: | S/TPP/FHEXM-4X8-NI |
| Парткод: | X0-02251000 |
| Деталь: | ASYS-BRKT-DRV-WTNR |
| Парткод: | 6LH39221000 |
| Деталь: | GEAR-5H49-CPL |
| Парткод: | 6LH39233000 |
| Деталь: | GEAR-5H21_P2GT60-6 |
| Парткод: | 6LH39231000 |
| Деталь: | MOTRD-AUG-450CW |
| Парткод: | 6LH39805000 |
| Деталь: | BLT_SY-202-2GT-4 |
| Парткод: | 6LH39234000 |
| Деталь: | ASYS-BRKT-DRV-WTNR-SUB |
| Парткод: | 6LH39225000 |
| Деталь: | GEAR-5H47-6 |
| Парткод: | 6LH39232000 |
| Деталь: | HRNS-AUGMTR-450 |
| Парткод: | 6LH39797000 |
| Деталь: | HLDR-SENS-THERM |
| Парткод: | 6LH39237000 |
| Деталь: | CHS-CSC-20 |
| Парткод: | D0-27874000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/PAN-M2.6X2.5-NI |
| Парткод: | X0-02270000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | S/TPS/FHEXM-3X8-ZU3 |
| Парткод: | X0-02239000 |
| Деталь: | ES-0505 |
| Парткод: | F0-00120000 |
| Деталь: | MSB-1207 |
| Парткод: | F0-01250000 |
| Деталь: | SHAFT-DRV-SCAN |
| Парткод: | 6LA39397000 |
| Деталь: | PLY-WIRE-SCAN |
| Парткод: | 6LA01742000 |
| Деталь: | ASYS-WIR_RP-SCAN-FRT |
| Парткод: | 6LA39410000 |
| Деталь: | ASYS-WIR_RP-SCAN-RER |
| Парткод: | 6LA39430000 |
| Деталь: | BRKT-MOTR-SCAN-410 |
| Парткод: | 6LE46348000 |
| Деталь: | MOTR_S-SCN-450 |
| Парткод: | 6LH39762000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | SHAFT-OPN-SNS |
| Парткод: | 6LA67393000 |
| Деталь: | SPR-OPEN-SNS |
| Парткод: | 44202846000 |
| Деталь: | LVR-OPEN-SNS |
| Парткод: | 44202845000 |
| Деталь: | SPE-WIRE-TENS |
| Парткод: | 44202660000 |
| Деталь: | BLT_SY-555-STS1.5-6 |
| Парткод: | 6LH37816000 |
| Деталь: | 608ZZNRA2 |
| Парткод: | F0-01360000 |
| Деталь: | SCREW-ACTR-TRU |
| Парткод: | 6LA08932000 |
| Деталь: | PULLEY-SCAN-450 |
| Парткод: | 6LH37814000 |
| Деталь: | COVER-PILLEY |
| Парткод: | 6LA39784000 |
| Деталь: | S/PAN/SWWP-M3X8-NI |
| Парткод: | X0-00077000 |
| Деталь: | S/TPS/BID-4X8-ZU3 |
| Парткод: | X0-02074000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | UAMS-05-2 |
| Парткод: | F0-00044000 |
| Деталь: | HR-FC28-L |
| Парткод: | 6LE98368000 |
| Деталь: | COV-PR-SCR-450 |
| Парткод: | 6LH36233000 |
| Деталь: | SPG-E-FUS-SCR-45X |
| Парткод: | 6LH36230000 |
| Деталь: | COVER-PR-HNS-R-FC |
| Парткод: | 6LH36320000 |
| Деталь: | COVER-PR-450M-FC |
| Парткод: | 6LH36319000 |
| Деталь: | BRKT-SCRP-PR-450 |
| Парткод: | 6LH36213000 |
| Деталь: | GEAR-10S040-FUS |
| Парткод: | 6LE25927000 |
| Деталь: | BRKT-PR-THM-450-E |
| Парткод: | 6LH36242000 |
| Деталь: | BRKT-PR-SEN-NT |
| Парткод: | 6LE25891000 |
| Деталь: | BRKT-LAMP-HLD |
| Парткод: | 6LE25885000 |
| Деталь: | BRKT-PR-ELEC-K2 |
| Парткод: | 6LE25883000 |
| Деталь: | THRMST-PRS-380 |
| Парткод: | 6LE29433000 |
| Деталь: | LBL-HOT-45X |
| Парткод: | 6LH36303000 |
| Деталь: | BRKT-PR-SPR-450 |
| Парткод: | 6LH36222000 |
| Деталь: | SPG-E-SCRP-F380 |
| Парткод: | 6LE25949000 |
| Деталь: | SCRAPR-FUS-350 |
| Парткод: | 6LA36256000 |
| Деталь: | SPR-PRESS-BRG |
| Парткод: | 44217749000 |
| Деталь: | SCREW-PR-SPR |
| Парткод: | 6LE25871000 |
| Деталь: | HRNS-FUS-PRS-F-380 |
| Парткод: | 6LE29349000 |
| Деталь: | HRNS-FUS-PRS-R-380 |
| Парткод: | 6LE29348000 |
| Деталь: | SHEET-COV-PR |
| Парткод: | 6LH36305000 |
| Деталь: | GUIDE-ENT-PR-450-V |
| Парткод: | 6LH36279000 |
| Деталь: | GUIDE-ENT-FUS-FC |
| Парткод: | 6LH36322000 |
| Деталь: | SHAFT-FUS-8 |
| Парткод: | 6LE25810000 |
| Деталь: | GEAR-10S-29-2 |
| Парткод: | 6LE25912000 |
| Деталь: | SPG-E-FUS-PR |
| Парткод: | 6LE25852000 |
| Деталь: | SCREW-SFT-8-V |
| Парткод: | 6LH36301000 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 6LA08937000 |
| Деталь: | BRUSH-FUSER |
| Парткод: | 6LE06670000 |
| Деталь: | 6805ZZS1C4KZ |
| Парткод: | F0-01361000 |
| Деталь: | UAMS-05L-0-46 |
| Парткод: | F0-00270000 |
| Деталь: | PLWS-1-46B |
| Парткод: | F0-00032000 |
| Деталь: | S/FHEXM-M3X6-NI |
| Парткод: | X0-02230000 |
| Деталь: | S/PAN/SWWP-M3X10-NI |
| Парткод: | X0-00094000 |
| Деталь: | S/PAN/SWWP-M3X5-NI |
| Парткод: | X0-00050000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | THMS-PRS-450 |
| Парткод: | 6LH39784000 |
| Деталь: | THMS-PRS-454 |
| Парткод: | 6LH39785000 |
| Деталь: | LAMP-PR-115-45X |
| Парткод: | 6LH36259000 |
| Деталь: | LAMP-PR-230-45X |
| Парткод: | 6LH36257000 |
| Деталь: | HANDLE-EPU-LOCK |
| Парткод: | 6LE23173000 |
| Деталь: | SPG-C-HANDLE-LOCK |
| Парткод: | 6LE23174000 |
| Деталь: | COVER-CNCT-EPU |
| Парткод: | 6LE23172000 |
| Деталь: | LBL-PSN-LSU-CLN |
| Парткод: | 6LE23205000 |
| Деталь: | HANDL-CHARGR-CLNR-380 |
| Парткод: | 6LE23566000 |
| Деталь: | TERM-HVT-EPU-380 |
| Парткод: | 6LE23703000 |
| Деталь: | SPG-C-BIAS-DEV-380 |
| Парткод: | 6LE23706000 |
| Деталь: | SPG-C-BIAS-BLADE-380 |
| Парткод: | 6LE23714000 |
| Деталь: | PLATE-BIAS-CHARGR-380 |
| Парткод: | 6LE23704000 |
| Деталь: | SPG-F-BIAS-GRID-380 |
| Парткод: | 6LE23705000 |
| Деталь: | STAY-EPU-UPR-380 |
| Парткод: | 6LE23707000 |
| Деталь: | S/TPP/BID-38-NI |
| Парткод: | 6LA80090000 |
| Деталь: | COVER-EPU-45X-K |
| Парткод: | 6LH33530000 |
| Деталь: | COVER-EPU-45X-Y |
| Парткод: | 6LH33529000 |
| Деталь: | COVER-EPU-45X-M |
| Парткод: | 6LH33530200 |
| Деталь: | COVER-EPU-45X-C |
| Парткод: | 6LH33530100 |
| Деталь: | HRNS-MCEPU-450 |
| Парткод: | 6LH39908000 |
| Деталь: | HRNS-YKEPU-450 |
| Парткод: | 6LH39907000 |
| Деталь: | S/FHEXM-M3X8-NI |
| Парткод: | X0-02231000 |
| Деталь: | S/TPP/FHEXM-3X8-NI |
| Парткод: | X0-02247000 |
| Деталь: | S/TPP/FHEXM-4X8-NI |
| Парткод: | X0-02251000 |
| Деталь: | 608ZZNR2KS |
| Парткод: | F0-01388000 |
| Деталь: | HRNS-HVPS-KPU-380 |
| Парткод: | 6LE29415000 |
| Деталь: | HRNS-HVPS-YPS-380 |
| Парткод: | 6LE29412000 |
| Деталь: | HRNS-HVPS-MPU-380 |
| Парткод: | 6LE29413000 |
| Деталь: | HRNS-HVPS-CPU-380 |
| Парткод: | 6LE29414000 |
Коды ошибок
C040
C130
C140
C150
C160
C180
C1A0
C1B0
C260
C270
C280
C290
C370
C380
C381
C390
C391
C3A0
C3A1
C3B0
C3B1
C411
C412
C443
C445
C446
C447
C448
C449
C450
C451
C452
C465
C466
C467
C468
C4B0
C4B1
C4D0
C550
C570
C580
C5A0
C5A1
C8E0
C900
C901
C910
C911
C940
C962
C970
C9E0
CA00
CA10
CA20
CB00
CB01
CB10
CB11
CB12
CB13
CB14
CB20
CB30
CB31
CB40
CB50
CB51
CB60
CB80
CB81
CB82
CB83
CB84
CB91
CB92
CB93
CB94
CB95
CBA0
CBB0
CBC0
CBE0
CC20
CC30
CC31
CC41
CC51
CC52
CC61
CC71
CC72
CC80
CC90
CCB0
CCF1
CD70
CD71
CD72
CDE0
CE00
CE10
CE20
CE40
CE50
CE60
CE70
CE71
CE90
CEC1
CEC2
CF10
CF90
E010
E011
E020
E030
E061
E062
E063
E064
E065
E090
E091
E0A0
E110
E120
E130
E140
E150
E160
E190
E200
E210
E220
E270
E300
E310
E320
E330
E340
E350
E360
E3C0
E3D0
E3E0
E400
E410
E420
E430
E440
E450
E480
E4A0
E510
E520
E550
E551
E552
E712
E714
E721
E722
E724
E725
E726
E731
E860
E870
E871
E910
E920
E930
E940
E9F0
EA10
EA20
EA21
EA22
EA23
EA24
EA25
EA26
EA27
EA28
EA29
EA30
EA31
EA32
EA40
EA50
EA60
EA70
EA90
EAA0
EAB0
EAB1
EAD0
EAE0
EB30
EB50
EB60
ED10
ED11
ED12
ED13
ED14
ED15
ED16
EF10
EF11
EF12
EF13
EF14
EF15
EF16
EF17
EF18
EF19
EF20
F100_0
F100_1
F100_2
F101_0
F101_1
F101_2
F101_3
F102
F103
F104
F106_0
F106_1
F106_2
F106_3
F106_4
F106_5
F109_0
F109_1
F109_2
F109_3
F109_4
F109_5
F109_6
F110
F111
F120
F121
F122
F124
F130
F131
F140
F200
F400
F500
F510
F520
F521
F550
F600
F700
F800
F900
Описание
| Error code: | C040 |
| Description: | PFP motor abnormality: The PFP motor is not rotating normally. |
| Causes: | PFP motor PFP board LGC board |
| Remedy: | 1 Is the PFP motor working? (Perform the output check in the test mode: 03-109/ 159) Yes 2 No 1. Check if the signal line connector CN506 of the PFP motor is disconnected. 2. Check if the connector CN246 on the PFP board is disconnected. 3. Check if the connector CN241 on the PFP board is disconnected. 4. Check if the connector CN318 on the LGC board is disconnected. 5. Check if the connector pins are disconnected and the harnesses are open circuited. 6. Check if the conductor patterns on the PFP motor board, PFP board and LGC board are short circuited or open circuited. 7. Replace the PFP motor. 8. Replace the PFP board. 9. Replace the LGC board. 2 Is the LED on the PFP motor board lit without flickering? Yes 3 No 1. Check if the connector pins are disconnected and the harnesses are open circuited. 2. Check if the conductor patterns on the PFP motor board, PFP board and LGC board are short circuited or open circuited. 3. Replace the PFP motor. 4. Replace the PFP board. 5. Replace the LGC board. 3 PFP board LGC board 1. Check if the PLL lock signal CN246-7 output from the PFP board is always "L" level. 2. Check if the voltage supplied to the microcomputer input terminal IC5-17 is always "L" level. 3. Replace the PFP board. 4. Replace the LGC board. |
| Error code: | C130 |
| Description: | 1st drawer tray abnormality: The tray-up motor-1 does not run normally or the 1st drawer tray does not move normally. (Feeding of any other drawer than the 1st drawer is possible.) |
| Causes: | Tray-up motor Tray-up sensor PFC board |
| Remedy: | Does the tray go up? (Perform the output check in the test mode: 03-276,278,279,280) ↓ → NO → 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector CN331 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[E], /[2]/[E], /[3]/[E] ,/[4]/[E]) ↓ → NO → 1. Check if the connector of the sensor is disconnected. 2. Check if the connector CN329, CN328, CN350 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. YES 1. Check if the positioning pin of the drawer is tightly screwed. 2. Check if the paper is not caught in the coupling when the tray goes up. 3. Check if the conductor pattern on the LGC board is short circuited or open circuited. 4. Replace the LGC board. |
| Error code: | C140 |
| Description: | 2nd drawer tray abnormality: The tray-up motor-1 does not run normally or the 2nd drawer tray does not move normally. (Feeding of any other drawer than the 2nd drawer is possible.) |
| Causes: | Tray-up motor Tray-up sensor PFC board |
| Remedy: | Does the tray go up? (Perform the output check in the test mode: 03-276,278,279,280) ↓ → NO → 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector CN331 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[E], /[2]/[E], /[3]/[E] ,/[4]/[E]) ↓ → NO → 1. Check if the connector of the sensor is disconnected. 2. Check if the connector CN329, CN328, CN350 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. YES 1. Check if the positioning pin of the drawer is tightly screwed. 2. Check if the paper is not caught in the coupling when the tray goes up. 3. Check if the conductor pattern on the LGC board is short circuited or open circuited. 4. Replace the LGC board. |
| Error code: | C150 |
| Description: | 3rd drawer tray abnormality: The tray-up motor-2 does not run normally or the 3rd drawer tray does not move normally. (Feeding of any other drawer than the 3rd drawer is possible.) |
| Causes: | Tray-up motor Tray-up sensor PFC board |
| Remedy: | Does the tray go up? (Perform the output check in the test mode: 03-276,278,279,280) ↓ → NO → 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector CN331 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[E], /[2]/[E], /[3]/[E] ,/[4]/[E]) ↓ → NO → 1. Check if the connector of the sensor is disconnected. 2. Check if the connector CN329, CN328, CN350 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. YES 1. Check if the positioning pin of the drawer is tightly screwed. 2. Check if the paper is not caught in the coupling when the tray goes up. 3. Check if the conductor pattern on the LGC board is short circuited or open circuited. 4. Replace the LGC board. |
| Error code: | C160 |
| Description: | 4th drawer tray abnormality: The tray-up motor-2 does not run normally or the 4th drawer tray does not move normally. (Feeding of any other drawer than the 4th drawer is possible.) |
| Causes: | Tray-up motor Tray-up sensor PFC board |
| Remedy: | Does the tray go up? (Perform the output check in the test mode: 03-276,278,279,280) ↓ → NO → 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector CN331 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[E], /[2]/[E], /[3]/[E] ,/[4]/[E]) ↓ → NO → 1. Check if the connector of the sensor is disconnected. 2. Check if the connector CN329, CN328, CN350 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. YES 1. Check if the positioning pin of the drawer is tightly screwed. 2. Check if the paper is not caught in the coupling when the tray goes up. 3. Check if the conductor pattern on the LGC board is short circuited or open circuited. 4. Replace the LGC board. |
| Error code: | C180 |
| Description: | Tandem LCF tray-up motor abnormality: The Tandem LCF tray-up motor does not run normally or the Tandem LCF tray does not move normally. (Feeding of any other drawer than the Tandem LCF is possible.) |
| Causes: | LCF tray-up motor LCF tray-up sensor LCF tray bottom sensor PFC board |
| Remedy: | Does the tray move? (Perform the output check in the test mode: 03-270) ↓ → NO → 1. Check if the connector of the Tandem LCF tray-up motor is disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 5. Replace the LCF tray-up moter. 6. Replace the LGC board. YES Are the 3rd drawer/tandem LCF tray-up sensor and tandem LCF bottom sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[3]/[E], /[8]/[F]) ↓ → NO → 1. Check if the connectors of the sensors are disconnected. 2. Check if the connector CN328, CN345 on the LGC board is disconnected. 3. Check if the slit reaches the sensors. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 6. Replace the LGC board. YES 1. Check if the driving mechanism is abnormal. 2. Check if the conductor pattern on the LGC board is short circuited or open circuited. 3. Replace the LGC board. |
| Error code: | C1A0 |
| Description: | Tandem LCF end fence motor abnormality: The Tandem LCF end fence motor does not run normally or the Tandem LCF end fence does not move normally. (Feeding of any other drawer than the Tandem LCF is possible.) |
| Causes: | LCF end fence motor LCF end fence home position sensor LCF end fence stop position sensor PFC board |
| Remedy: | Is the Tandem LCF end fence motor working? (Perform the output check in the test mode: 03-207) ↓ → NO → 1. Check if the connector of the Tandem LCF end fence motor is disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 5. Replace the Tanden LCF end fence motor. 6. Replace the LGC board. YES Are the LCF end fence stop position sensors working? (Perform the input check in the test mode: 03-[FAX]OFF/[8]/[G], /[8]/[H]) ↓ → NO → 1. Check if the connectors of the sensors are disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the slit reaches the sensors. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 6. Replace the LGC board. YES 1. Check if the driving mechanism is abnormal. 2. Check if the conductor pattern on the LGC board is short circuited or open circuited. 3. Replace the LGC board. |
| Error code: | C1B0 |
| Description: | LCF transport motor abnormality: The LCF transport motor is not rotating normally. |
| Causes: | LCF transport motor LCF board LGC board |
| Remedy: | 1 Is the LCF transport motor working? (Perform the output check in the test mode: 03-122/172) Yes 2 No 3 2 LCF transport motor LCF board LGC board 1. Check if the connector pins are disconnected and the harnesses are open circuited. 2. Check if the conductor patterns on the LCF transport motor board, LCF board and LGC board are short circuited or open circuited. 3. Check if the PLL lock signal CN3-10 output from the LCF board is always "L" level. 4. Check if the voltage supplied to the microcomputer input terminal IC103-17 is always "L" level. 5. Replace the LCF transport motor. 6. Replace the LCF board. 7. Replace the LGC board. 3 LCF transport motor LCF board LGC board 1. Check if the connector of the LCF transport motor is disconnected. 2. Check if the connector CN1, CN3 on the LCF board is disconnected. 3. Check if the connector CN318 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the LCF transport motor board, LCF board and LGC board are short circuited or open circuited. 6. Replace the LCF transport motor. 7. Replace the LCF board. 8. Replace the LGC board. |
| Error code: | C260 |
| Description: | Peak detection error: Lighting of the exposure lamp (white reference) is not detected when the power is turned ON. |
| Causes: | Lens unit SLG board Exposure lamp Supply harness |
| Remedy: | Does the exposure lamp light? (Perform the output check in the test mode: 03-267) ↓ → YES → 1. Check if the connectors on the CCD and SLG boards are disconnected. 2. Check if the shading correction plate is detached or dirty. 3. Check if the conductor pattern on the CCD board is short circuited or open circuited. 4. Check if the conductor pattern on the SLG board is short circuited or open circuited. 5. Replace the lens unit. 6. Replace the SLG board. NO 1. Check if the connectors of the exposure lamp and inverter are disconnected. 2. Check the SLG board if the connector pin CN1 is disconnected and the harness is short circuited or open circuited. 3. Check if the conductor pattern on the SLG board is short circuited or open circuited. 4. Replace the SLG board. 5. Replace the inverter. 6. Replace the exposure lamp. |
| Error code: | C270 |
| Description: | Carriage home position sensor not turning OFF within a specified period of time: The carriages do not shift from their home position within a specified period of time. |
| Causes: | Carriage home position sensor Carriage home position sensor harness SLG board Scan motor Scan motor harness |
| Remedy: | Remove the original glass and move the carriages to the paper feeding side. Turn ON the power and check the following items. Are the carriages slightly moved to the feeding direction? Are the carriages staying at a position other than home position? ll → YES → 1. Check if the conductor pattern on the SLG board is short circuited or open circuited. 2. Replace the SLG board. NO 1. Check if the connector pin is disconnected and the harness is short circuited or open circuited. 2. Check if the conductor pattern on the SLG board is short circuited or open circuited. 3. Replace the SLG board. |
| Error code: | C280 |
| Description: | Carriage home position sensor not turning ON within a specified period of time: The carriages do not reach their home position within a specified period of time. |
| Causes: | Carriage home position sensor Carriage home position sensor harness SLG board Scan motor Scan motor harness |
| Remedy: | Do the carriages make a big noise after they arrive at the home position? ↓ → YES → The carriage home position sensor is not turned ON. 1. Check if the connector of the sensor is disconnected. 2. Replace the carriage home position sensor. 3. Check if the conductor pattern on the SLG board is short circuited or open circuited. 4. Replace the SLG board. NO The carriages are stopped at the home position and do not move. 1. Check if the connector pins are disconnected and the harnesses are short circuited or open circuited. 2. Check if the conductor pattern on the SLG board is short circuited or open circuited. 3. Replace the SLG board. |
| Error code: | C290 |
| Description: | Scanner fuse blowout: 24V power for the scanning system is not supplied at the scanner warming-up after power-ON. |
| Causes: | SLG board Fuse Supply harness LVPS |
| Remedy: | 1 Is 24V supplied to the SLG board? Yes Supplied. 2 No Not supplied. 3 2 SLG board Check the following because the signal for checking 24V on the SLG board is abnormal. 1. Check if 3V is input in 35 Pin of the scanner CPU (IC15). 2. Check if the mounted parts on the SLG board are damaged or abnormal. 3 Supply harness 1. Check if the supply harness is connected properly to the connector. SLG board 1. Check if 24V and SG on the SLG board are short circuited. 2. Check if the power supply is short circuited by pulling out the supply harness on the SLG board. LVPS 1. Check if the fuse on the LVPS is open circuited. |
| Error code: | C370 |
| Description: | Transfer belt cam motor abnormality: The transfer belt cam motor does not run normally when the power is turned ON or the copying is started. |
| Causes: | Transfer belt contact/release detection sensor Transfer belt motor DRV board LGC board |
| Remedy: | (1) Is the transport belt unit working normally? (there is no extraneous material or toner clod). (2) Check if the connector of the transfer belt cam motor is not disconnected. (3) Check if the connector CN335 on the LGC board is disconnected. (4) Check if the fuse on the LVPS has blown. (5) Check if the transfer belt release detection sensor and transfer belt contact detection sensor is working properly. (6) Replace the transfer belt cam motor. (7) Replace the LGC board. |
| Error code: | C380 |
| Description: | Auto-toner sensor-K abnormality (upper limit) |
| Causes: | Auto-toner sensor-K/-C/-M/-Y Developer unit mixer motor-K/YMC EPU board LGC board |
| Remedy: | (1) Check if there is any abnormality on the connector between the equipment and the EPU tray of the process unit. (05-2788) (2) Check if the process unit (EPU tray) is securely installed. (3) Check if the harnesses between the connectors (CN550, CN551, CN555) on the EPU board, the drawer connectors for the LGC board of the EPU tray, and the connector of the LGC board are disconnected or open-circuited. (4) Check if the harnesses between the connectors (CN553, CN554, CN555, and CN556) and the auto toner sensor are disconnected or open-circuited. (5) Replace the auto-toner sensor. (6) Replace the EPU board. (7) Replace the LGC board. |
| Error code: | C381 |
| Description: | Auto-toner sensor-K abnormality (lower limit) |
| Causes: | Auto-toner sensor-K/-C/-M/-Y Developer unit mixer motor-K/YMC EPU board LGC board |
| Remedy: | (1) Check if there is any abnormality on the connector between the equipment and the EPU tray of the process unit. (05-2788) (2) Check if the process unit (EPU tray) is securely installed. (3) Check if the harnesses between the connectors (CN550, CN551, CN555) on the EPU board, the drawer connectors for the LGC board of the EPU tray, and the connector of the LGC board are disconnected or open-circuited. (4) Check if the harnesses between the connectors (CN553, CN554, CN555, and CN556) and the auto toner sensor are disconnected or open-circuited. (5) Replace the auto-toner sensor. (6) Replace the EPU board. (7) Replace the LGC board. |
| Error code: | C390 |
| Description: | Auto-toner sensor-C abnormality (upper limit) |
| Causes: | Auto-toner sensor-K/-C/-M/-Y Developer unit mixer motor-K/YMC EPU board LGC board |
| Remedy: | (1) Check if there is any abnormality on the connector between the equipment and the EPU tray of the process unit. (05-2788) (2) Check if the process unit (EPU tray) is securely installed. (3) Check if the harnesses between the connectors (CN550, CN551, CN555) on the EPU board, the drawer connectors for the LGC board of the EPU tray, and the connector of the LGC board are disconnected or open-circuited. (4) Check if the harnesses between the connectors (CN553, CN554, CN555, and CN556) and the auto toner sensor are disconnected or open-circuited. (5) Replace the auto-toner sensor. (6) Replace the EPU board. (7) Replace the LGC board. |
| Error code: | C391 |
| Description: | Auto-toner sensor-C abnormality (lower limit) |
| Causes: | Auto-toner sensor-K/-C/-M/-Y Developer unit mixer motor-K/YMC EPU board LGC board |
| Remedy: | (1) Check if there is any abnormality on the connector between the equipment and the EPU tray of the process unit. (05-2788) (2) Check if the process unit (EPU tray) is securely installed. (3) Check if the harnesses between the connectors (CN550, CN551, CN555) on the EPU board, the drawer connectors for the LGC board of the EPU tray, and the connector of the LGC board are disconnected or open-circuited. (4) Check if the harnesses between the connectors (CN553, CN554, CN555, and CN556) and the auto toner sensor are disconnected or open-circuited. (5) Replace the auto-toner sensor. (6) Replace the EPU board. (7) Replace the LGC board. |
| Error code: | C3A0 |
| Description: | Auto-toner sensor-M abnormality (upper limit) |
| Causes: | Auto-toner sensor-K/-C/-M/-Y Developer unit mixer motor-K/YMC EPU board LGC board |
| Remedy: | (1) Check if there is any abnormality on the connector between the equipment and the EPU tray of the process unit. (05-2788) (2) Check if the process unit (EPU tray) is securely installed. (3) Check if the harnesses between the connectors (CN550, CN551, CN555) on the EPU board, the drawer connectors for the LGC board of the EPU tray, and the connector of the LGC board are disconnected or open-circuited. (4) Check if the harnesses between the connectors (CN553, CN554, CN555, and CN556) and the auto toner sensor are disconnected or open-circuited. (5) Replace the auto-toner sensor. (6) Replace the EPU board. (7) Replace the LGC board. |
| Error code: | C3A1 |
| Description: | Auto-toner sensor-M abnormality (lower limit) |
| Causes: | Auto-toner sensor-K/-C/-M/-Y Developer unit mixer motor-K/YMC EPU board LGC board |
| Remedy: | (1) Check if there is any abnormality on the connector between the equipment and the EPU tray of the process unit. (05-2788) (2) Check if the process unit (EPU tray) is securely installed. (3) Check if the harnesses between the connectors (CN550, CN551, CN555) on the EPU board, the drawer connectors for the LGC board of the EPU tray, and the connector of the LGC board are disconnected or open-circuited. (4) Check if the harnesses between the connectors (CN553, CN554, CN555, and CN556) and the auto toner sensor are disconnected or open-circuited. (5) Replace the auto-toner sensor. (6) Replace the EPU board. (7) Replace the LGC board. |
| Error code: | C3B0 |
| Description: | Auto-toner sensor-Y abnormality (upper limit) |
| Causes: | Auto-toner sensor-K/-C/-M/-Y Developer unit mixer motor-K/YMC EPU board LGC board |
| Remedy: | (1) Check if there is any abnormality on the connector between the equipment and the EPU tray of the process unit. (05-2788) (2) Check if the process unit (EPU tray) is securely installed. (3) Check if the harnesses between the connectors (CN550, CN551, CN555) on the EPU board, the drawer connectors for the LGC board of the EPU tray, and the connector of the LGC board are disconnected or open-circuited. (4) Check if the harnesses between the connectors (CN553, CN554, CN555, and CN556) and the auto toner sensor are disconnected or open-circuited. (5) Replace the auto-toner sensor. (6) Replace the EPU board. (7) Replace the LGC board. |
| Error code: | C3B1 |
| Description: | Auto-toner sensor-Y abnormality (lower limit) |
| Causes: | Auto-toner sensor-K/-C/-M/-Y Developer unit mixer motor-K/YMC EPU board LGC board |
| Remedy: | (1) Check if there is any abnormality on the connector between the equipment and the EPU tray of the process unit. (05-2788) (2) Check if the process unit (EPU tray) is securely installed. (3) Check if the harnesses between the connectors (CN550, CN551, CN555) on the EPU board, the drawer connectors for the LGC board of the EPU tray, and the connector of the LGC board are disconnected or open-circuited. (4) Check if the harnesses between the connectors (CN553, CN554, CN555, and CN556) and the auto toner sensor are disconnected or open-circuited. (5) Replace the auto-toner sensor. (6) Replace the EPU board. (7) Replace the LGC board. |
| Error code: | C411 |
| Description: | Thermistor/heater abnormality at power-ON: Thermistor abnormality is detected at power-ON or the fuser roller temperature does not rise within a specified period of time after power-ON. |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1.Check the power voltage (1) Check if the power voltage is normal.(Is the voltage during the operation ±10% of the rated voltage?) 2.Check the thermistors (1) Check if the connectors are disconnected. (2) Check if the center and side thermistors (front, rear) are in contact with the surface of the fuser roller properly? (3) Check if the harnesses of the center and side thermistors (front, rear) are open circuited. 3. Check the heater (1) Check if the IH coil is broken. (2) Check if the connector of the IH coil is disconnected. (3) Check if the thermostat is blown. (4) Check if the connectors on the IH control board are disconnected (AC input connector and LGC I/F connectors CN455). (5) Check if the IH control board is abnormal. • Replace the IH control board. 4. Check the LGC board (1) Check if the connectors CN332,CN334 are disconnected. (2) Check if the conductor pattern on the LGC board is short circuited or open circuited. (3) Replace the LGC board. 5. Clear the status counter After repairing the matter which caused the error [C411/C412], perform the following: (1) Turn ON the power while [0] and [8] are pressed simultaneously. (2) Key in "400", then press [START]. (3) Change the current status counter value "1" or "2" to "0", then press [ENTER] or [INTERRUPT] (to cancel [C411/C412]). (4) Turn the power OFF and then back ON. Make sure that the equipment enters the normal ready state. |
| Error code: | C412 |
| Description: | Thermistor/heater abnormality at power-ON: Thermistor abnormality is detected at power-ON or the fuser roller temperature does not rise within a specified period of time after power-ON. |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1.Check the power voltage (1) Check if the power voltage is normal.(Is the voltage during the operation ±10% of the rated voltage?) 2.Check the thermistors (1) Check if the connectors are disconnected. (2) Check if the center and side thermistors (front, rear) are in contact with the surface of the fuser roller properly? (3) Check if the harnesses of the center and side thermistors (front, rear) are open circuited. 3. Check the heater (1) Check if the IH coil is broken. (2) Check if the connector of the IH coil is disconnected. (3) Check if the thermostat is blown. (4) Check if the connectors on the IH control board are disconnected (AC input connector and LGC I/F connectors CN455). (5) Check if the IH control board is abnormal. • Replace the IH control board. 4. Check the LGC board (1) Check if the connectors CN332,CN334 are disconnected. (2) Check if the conductor pattern on the LGC board is short circuited or open circuited. (3) Replace the LGC board. 5. Clear the status counter After repairing the matter which caused the error [C411/C412], perform the following: (1) Turn ON the power while [0] and [8] are pressed simultaneously. (2) Key in "400", then press [START]. (3) Change the current status counter value "1" or "2" to "0", then press [ENTER] or [INTERRUPT] (to cancel [C411/C412]). (4) Turn the power OFF and then back ON. Make sure that the equipment enters the normal ready state. |
| Error code: | C443 |
| Description: | Heater abnormality after abnormality judgment (not reaching to intermediate temperature) |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1,2.3. Check the thermistors, Heater and LGC board Check the above components following the procedures 1, 2 and 3 for [C411/C412]. 4. Clear the status counter Change the current status counter value (08-400) "3", "5" , "6" , "9" , "19" , "21" , "22" , "23" , "24" , "25" , "27" or "29" to "0" for [C44X], taking the same procedure as that for [C41X]. • The status counter value is as follows in the following cases. - The error occurred during warming-up: "3", "5" or "6" - The error occurred after the equipment has become ready: "7" - The temperature detected by the center thermistor is 240°C or higher, the temperature detected by the side thermistor is 250°C or higher or the temperature detected by the edge thermistor is 270°C or higher: "9", "19", "21", "22", "23", "25", "27" or "29". - The error occurred during printing: "24" or "25" - The error occurred during energy saving: "26" or "27" - A paper jam occurred: "28" or "29" |
| Error code: | C445 |
| Description: | Heater abnormality after abnormality judgment (prerunning end temperature abnormality) |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1,2.3. Check the thermistors, Heater and LGC board Check the above components following the procedures 1, 2 and 3 for [C411/C412]. 4. Clear the status counter Change the current status counter value (08-400) "3", "5" , "6" , "9" , "19" , "21" , "22" , "23" , "24" , "25" , "27" or "29" to "0" for [C44X], taking the same procedure as that for [C41X]. • The status counter value is as follows in the following cases. - The error occurred during warming-up: "3", "5" or "6" - The error occurred after the equipment has become ready: "7" - The temperature detected by the center thermistor is 240°C or higher, the temperature detected by the side thermistor is 250°C or higher or the temperature detected by the edge thermistor is 270°C or higher: "9", "19", "21", "22", "23", "25", "27" or "29". - The error occurred during printing: "24" or "25" - The error occurred during energy saving: "26" or "27" - A paper jam occurred: "28" or "29" |
| Error code: | C446 |
| Description: | Heater abnormality after abnormality judgment (prerunning end temperature abnormality) |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1,2.3. Check the thermistors, Heater and LGC board Check the above components following the procedures 1, 2 and 3 for [C411/C412]. 4. Clear the status counter Change the current status counter value (08-400) "3", "5" , "6" , "9" , "19" , "21" , "22" , "23" , "24" , "25" , "27" or "29" to "0" for [C44X], taking the same procedure as that for [C41X]. • The status counter value is as follows in the following cases. - The error occurred during warming-up: "3", "5" or "6" - The error occurred after the equipment has become ready: "7" - The temperature detected by the center thermistor is 240°C or higher, the temperature detected by the side thermistor is 250°C or higher or the temperature detected by the edge thermistor is 270°C or higher: "9", "19", "21", "22", "23", "25", "27" or "29". - The error occurred during printing: "24" or "25" - The error occurred during energy saving: "26" or "27" - A paper jam occurred: "28" or "29" |
| Error code: | C447 |
| Description: | Heater abnormality after abnormality judgment (temperature abnormality at ready status) |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1,2.3. Check the thermistors, Heater and LGC board Check the above components following the procedures 1, 2 and 3 for [C411/C412]. 4. Clear the status counter Change the current status counter value (08-400) "3", "5" , "6" , "9" , "19" , "21" , "22" , "23" , "24" , "25" , "27" or "29" to "0" for [C44X], taking the same procedure as that for [C41X]. • The status counter value is as follows in the following cases. - The error occurred during warming-up: "3", "5" or "6" - The error occurred after the equipment has become ready: "7" - The temperature detected by the center thermistor is 240°C or higher, the temperature detected by the side thermistor is 250°C or higher or the temperature detected by the edge thermistor is 270°C or higher: "9", "19", "21", "22", "23", "25", "27" or "29". - The error occurred during printing: "24" or "25" - The error occurred during energy saving: "26" or "27" - A paper jam occurred: "28" or "29" |
| Error code: | C448 |
| Description: | Heater lamp continuous lighting abnormality: Heater lamp lights continuously for a certain period of time when the pressure roller temperature during ready status is higher than the specified |
| Causes: | Thermopiles Fuser unit Power supply LGC board |
| Remedy: | 1. Check the power supply and fuser unit (1) Check if the fuser unit is installed properly. (2) Check if foreign matter or paper in the fuser unit is plugging up the monitoring opening of the fuser belt thermopile. (3) Check if the opening of the fuser belt thermopile of the equipment is plugged up. (4) Check if the connectors of the power supply are disconnected (power supply unit AC output connector CN409 and LGC Interface connector CN403). (5) Check if the power supply unit is abnormal. * Replace the power supply unit. 2. Check the LGC board (1) Check if the connector CN333 is disconnected. (2) Check if the conductor pattern on the LGC board is short circuited or open circuited. (3) Replace the LGC board. 3. Clear the status counter After repairing the matter which caused the error [C448], perform the following: (1) Turn the power ON while [0] and [8] are pressed simultaneously. (2) Key in “400”, then press the [START] button. (3) Change the displayed current status counter value “32” to “0”, then press [ENTER] or [INTERRUPT] (to cancel C448). (4) Turn the power OFF and then back ON. Make sure that the equipment enters the normal status. |
| Error code: | C449 |
| Description: | Heater abnormality after abnormality judgment (overheating) |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1,2.3. Check the thermistors, Heater and LGC board Check the above components following the procedures 1, 2 and 3 for [C411/C412]. 4. Clear the status counter Change the current status counter value (08-400) "3", "5" , "6" , "9" , "19" , "21" , "22" , "23" , "24" , "25" , "27" or "29" to "0" for [C44X], taking the same procedure as that for [C41X]. • The status counter value is as follows in the following cases. - The error occurred during warming-up: "3", "5" or "6" - The error occurred after the equipment has become ready: "7" - The temperature detected by the center thermistor is 240°C or higher, the temperature detected by the side thermistor is 250°C or higher or the temperature detected by the edge thermistor is 270°C or higher: "9", "19", "21", "22", "23", "25", "27" or "29". - The error occurred during printing: "24" or "25" - The error occurred during energy saving: "26" or "27" - A paper jam occurred: "28" or "29" |
| Error code: | C450 |
| Description: | Fuser unit related service call Thermistor abnormality during printing: Abnormality of the thermistor is detected during printing. |
| Causes: | LGC board |
| Remedy: | 1. Check the edge thermistor 1. Check if the connector is disconnected. 2. Check if the edge thermistor is in contact with the surface of the fuser roller properly. 3. Check if the harness of the edge thermistor is open circuited. 2. Check the LGC board 1. Check if the connector CN308 is disconnected. 2. Check if the conductor pattern on the board is short circuited or open circuited. 3. Replace the LGC board. 3. Clear the status counter 1. Change the current status counter value (08-2002) "6" to "0". |
| Error code: | C451 |
| Description: | Thermopile and edge thermistor temperature difference |
| Causes: | Power supply unit Thermopile LGC board |
| Remedy: | 1. Check if any paper is clinging to the fuser belt. 2. Check if there is any foreign matter between the fuser belt thermopile (center/side) and the fuser belt. Remove it if any. 3. Replace the fuser belt thermopile (center/side) |
| Error code: | C452 |
| Description: | Thermopile temperature difference |
| Causes: | Power supply unit Thermopile LGC board |
| Remedy: | 1.Check the power voltage (1) Check if the power voltage is normal.(Is the voltage during the operation ±10% of the rated voltage?) 2.Check the error detection history (1) Check the error detection history of each temperature detecting element when the error occurred. If any of the elements detects an abnormal temperature, check step 3. 08-1902: Fuser belt center thermopile temperature 08-1903: Fuser belt side thermopile temperature 08-1904: Fuser belt edge thermistor temperature 08-1905: Pressure roller center thermistor temperature 08-4545: Pressure roller rear thermistor temperature 3.Check the thermopiles (1) Check if the fuser belt center and side thermopiles (front, rear) are installed properly. (2) Check if the harnesses of the fuser belt center and side thermopiles (front, rear) are open circuited. 4. Check the IH board, IH coil and the fuser unit (1) Is the fuser unit installed correctly? (2) heck if foreign matter or paper in the fuser unit is plugging up the monitoring opening of the fuser belt thermopile. (3) Check if the opening of the fuser belt thermopile of the equipment is plugged up. (4) Is the IH coil open circuited? (Check if power is supplied to the IH coil.) (5) Check if the connector of the IH coil is disconnected. (6) Check if the thermostat is broken. (7) Check if any of the connectors (AC input connector and LGC I/F connector CN462) on the IH board is disconnected. (8) Is the IH board broken?. • Replace the IH board. 5. Check the LGC board (1) Check if the connectors CN333 and CN345 are disconnected. (2) Check if the conductor pattern on the LGC board is short circuited or open circuited. (3) Replace the LGC board. 6. Clear the status counter After repairing the matter which caused the error [C411/C412], perform the following: (1) Turn ON the power while [0] and [8] are pressed simultaneously. (2) Key in “400”, then press [START]. (3) Change the current status counter value “1” or “2” to “0”, then press [ENTER] or [INTERRUPT] (to cancel [C411/C412]). (4) Turn the power OFF and then back ON. Make sure that the equipment enters the normal ready state. |
| Error code: | C465 |
| Description: | Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality) |
| Causes: | Power supply unit LGC board |
| Remedy: | 1. Check the pressure roller thermistor (1) Check if the connector is disconnected. (2) Check if the pressure roller thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the pressure roller thermistor is open circuited. 2. Check the LGC board (1) Check if the connector CN332,CN334 is disconnected. (2) Check if the conductor pattern on the board is short circuited or open circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) "5", "6" , "7" , "8" , "18" , "20" , "24" , "26" or "28" to "0" |
| Error code: | C466 |
| Description: | Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality) |
| Causes: | Power supply unit LGC board |
| Remedy: | 1. Check the pressure roller thermistor (1) Check if the connector is disconnected. (2) Check if the pressure roller thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the pressure roller thermistor is open circuited. 2. Check the LGC board (1) Check if the connector CN332,CN334 is disconnected. (2) Check if the conductor pattern on the board is short circuited or open circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) "5", "6" , "7" , "8" , "18" , "20" , "24" , "26" or "28" to "0" |
| Error code: | C467 |
| Description: | Pressure roller thermistor abnormality after entering ready status (temperature abnormality at ready status) |
| Causes: | Pressure roller thermistor Fuser unit Power supply LGC board |
| Remedy: | 1. Check the pressure roller thermistor (1) Check if the connector is disconnected. (2) Check if the pressure roller thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the pressure roller thermistor is open circuited. 2. Check the LGC board (1) Check if the connector CN332,CN334 is disconnected. (2) Check if the conductor pattern on the board is short circuited or open circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) "5", "6" , "7" , "8" , "18" , "20" , "24" , "26" or "28" to "0" |
| Error code: | C468 |
| Description: | Pressure roller thermistor abnormality after entering ready status (overheating) |
| Causes: | Pressure roller thermistor Fuser unit Power supply LGC board |
| Remedy: | 1. Check the pressure roller thermistor (1) Check if the connector is disconnected. (2) Check if the pressure roller thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the pressure roller thermistor is open circuited. 2. Check the LGC board (1) Check if the connector CN332,CN334 is disconnected. (2) Check if the conductor pattern on the board is short circuited or open circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) "5", "6" , "7" , "8" , "18" , "20" , "24" , "26" or "28" to "0" |
| Error code: | C4B0 |
| Description: | Fuser unit counter abnormality |
| Causes: | LGC board |
| Remedy: | 1. Check the LGC board (1) Check if the conductor pattern on the board is short circuited or open circuited. (2) Check if NVRAM is mounted. (3) Replace the LGC board. 2. Clear the status counter Change the current status counter value (08-400) "30 or more" or "4" to "0". |
| Error code: | C4B1 |
| Description: | Fuser unit voltage judgment abnormality |
| Causes: | Fuser unit LGC board Switching regulator IH board |
| Remedy: | (1) Check if any of the harnesses in the fuser unit is open circuited. (2) Check if any of the connectors CN305, CN306 and CN330 on the LGC board is open circuited. (3) Check if there is any abnormality on the harnesses between the connectors CN305, CN306 and CN330 on the LGC board and the fuser unit. (4) Replace the LGC board. (5) Replace the fuser unit. (6) Check if the AC input connector on the IH board is disconnected. (7) Check if the connector CN404 of the switching regulator is disconnected. (8) Check if the fuse of the IH board has blown. (9) Replace the IH board. (10) Replace the FIL board. |
| Error code: | C4D0 |
| Description: | Fuser belt thermopile abnormality |
| Causes: | Thermistor LGC board |
| Remedy: | 1. Check the thermopile (1) Check if the connector of the thermopile is disconnected. (2) Check if the harnesses of the fuser belt center thermopile and the fuser belt side thermopile are open circuited. (3) Replace the thermopile. 2. Check the LGC board (1) Check if the connector CN333 is disconnected. (2) Check if the conductor pattern on the LGC board is open circuited or short circuited. (3) Replace the LGC board. 3. Cancel the service call After repairing the matter which caused the error [C4D0], turn the power OFF and then back ON to cancel the service call. However, the counter value will be stored until it is written over by the value of the other service call. |
| Error code: | C550 |
| Description: | RADF interface error: Communication error has occurred between the RADF and the scanner. |
| Causes: | RADF board Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-3210). SLG board |
| Remedy: | (1) Check if the harness connecting the ADF board and SLG board is disconnected or open circuited. (2) Check if the conductor pattern on the ADF board is short circuited or open circuited. (3) Check if the conductor pattern on the SLG board is short circuited or open circuited. (4) Replace the ADF board. (5) Replace the SLG board. |
| Error code: | C570 |
| Description: | Communication error between Engine-CPU and IPC board |
| Causes: | LGC board |
| Remedy: | (1) Check if the LGC board and IPC board are connected properly. (2) Check if the conductor pattern on the IPC board is short circuited or open circuited. (3) Check if the conductor pattern on the LGC board is short circuited or open circuited. (4) Replace the IPC board. (5) Replace the LGC board. |
| Error code: | C580 |
| Description: | Communication error between IPC board and Finisher |
| Causes: | LGC board Finisher controller board |
| Remedy: | (1) Check if the specified finisher is attached. (2) Check if the harness connecting the IPC board and the finisher controller PC board is disconnected or open circuited. (3) Check if the conductor pattern on the IPC board is short circuited or open circuited. (4) Check if the conductor pattern on the finisher controller PC board is short circuited or open circuited. (5) Replace the IPC board. (6) Replace the finisher controller PC board. |
| Error code: | C5A0 |
| Description: | SRAM board not connected (LGC board) |
| Causes: | SRAM board LGC board |
| Remedy: | (1) Check if the SRAM board has been installed properly. (2) Check if the conductor patterns on the SRAM board is short circuited or open circuited. (3) Check if the battery on the SRAM board has not run out. (4) Replace the SRAM board. (5) Replace the LGC board. |
| Error code: | C5A1 |
| Description: | NVRAM data abnormality (LGC board) |
| Causes: | SRAM board LGC board |
| Remedy: | (1) Check if the NVRAM has been installed properly. (2) Check if the conductor patterns on the NVRAM is short circuited or open circuited. (3) Replace the NVRAM. (4) Replace the LGC board. |
| Error code: | C8E0 |
| Description: | RADF communication protocol abnormality: The system has to be stopped because the control abnormality occurred. |
| Remedy: | 1. Turn the power OFF and then back ON to check if the equipment operates normally. |
| Error code: | C900 |
| Description: | Connection error between SYS board and LGC board |
| Causes: | LGC board If the problem is not corrected with the replacement of the LGC board, reinstall the removed LGC board and replace the IMG board. IMG board If the problem is still not corrected with the replacement of the IMG board, reinstall the removed IMG board and replace the SYS board. SYS board |
| Remedy: | (1) Check if the connector CN423, CN424 on the IMG board and the connector CN319, CN320 on the LGC board are completely inserted. (2) Check if the connector pin between the IMG board (connector CN423, CN424) and the LGC board (connector CN319, CN320) is disconnected. (3) Check if the connector CN422 on the IMG board and the connector CN135 on the SYS board are completely inserted. (4) Check if the connector pin between the IMG board (connector CN422) and the SYS board (connector CN135) is disconnected. (5) Check if the conductor patterns on the IMG board, LGC board and SYS board are short circuited or open circuited. (6) Replace the LGC board if no problem is found in steps from (1) to (5) above. (7) If the problem is not corrected with the replacement of the LGC board, reinstall the removed LGC board and replace the IMG board. (8) If the problem is still not corrected with the replacement of the IMG board, reinstall the removed IMG board and replace the SYS board. |
| Error code: | C901 |
| Description: | System format error for scanner |
| Causes: | SLG board SYS board |
| Remedy: | Main power switch Does service call still occur even after turning OFF the main power switch then back ON? SLG board • Connector check (CN12) • Board check SYS board • Connector check (CN135) • Board check |
| Error code: | C910 |
| Description: | Toner cartridge IC chip access board abnormality |
| Causes: | Toner cartridge LGC board HRNS-LGC-TNRIC-140 CTIF board HRNS-TNRIC-140 |
| Remedy: | 1 Does the non-genuine toner cartridge display appear when the front cover is opened and closed? Yes Use the genuine toner cartridge. 2 No 2 2 Toner cartridge • Check the phenomenon by removing the toner cartridges (Y, M, C and K) and reinserting them. • Check that the CTRG board of each cartridge (Y, M, C and K) is installed properly. 3 Contact point on the equipment side Check that the spring of the contact point for each color (Y, M, C and K) is not deformed. 4 Is the spring of the contact point returned when it is pushed lightly? Yes No • Check that the CTIF board is installed properly. • Board check 7 Notes: The spring of the contact point may be released if you push the toner cartridge all the way in when an abnormality occurs. 5 LGC board • Connector check (CN364) • Board check 6 HRNS-LGC-TNRIC-140 • Relay connector check (J556, J557, J558, J559) • Harness check 7 CTIF board for each color (Y, M, C and K) • Check that the board is installed properly. • Board check 8 HRNS-TNRIC-140 for each color (Y, M, C and K) • Connector check • Harness check |
| Error code: | C911 |
| Description: | Toner cartridge IC chip access board abnormality |
| Causes: | Toner cartridge LGC board HRNS-LGC-TNRIC-212 CTIF board |
| Remedy: | 1 Does non-genuine toner cartridge display appear when the front cover is opened and closed? Yes Use the genuine toner cartridge. No 2 2 Toner cartridge • Check the phenomenon by removing the toner cartridges (Y, M, C and K) and reinserting them. • Check that the CTRG board of each cartridge (Y, M, C and K) is installed properly. • Avoid touching the contact point. • Wipe the contact point with a soft cloth if it`s stained. 3 Contact point on the equipment side Check that the spring of the contact point for each color (Y, M, C and K) is not deformed. 4 Is the spring of the contact point returned when it is pushed lightly? Yes No • Check that the CTIF board is installed properly. • Board check 7 Notes: The spring of the contact point may be released if you push the toner cartridge all the way in when an abnormality occurs. 5 LGC board • Connector check (CN375) • Board check 6 HRNS-LGC-TNRIC-212 • Connector check (CN375, CN440) • Harness check 7 CTIF board for each color (Y, M, C and K) • Check that the board is installed properly. • Board check |
| Error code: | C940 |
| Description: | Engine-CPU abnormality |
| Causes: | LGC board |
| Remedy: | Is the “Call for Service” displayed even after the power is turned OFF and back ON? → NO → Leave it and see what happens. YES 1. Check if the circuit pattern between the Engine-CPU and FROM is short circuited or open circuited. 2. Replace the LGC board if this error occurs frequently. |
| Error code: | C962 |
| Description: | LGC board ID abnormality |
| Causes: | LGC board If the problem is not corrected with the replacement of the LGC board, reinstall the removed LGC board and replace the IMG board. IMG board If the problem is still not corrected with the replacement of the IMG board, reinstall it and ask a specialist to repair it. (Abnormal ID) |
| Remedy: | (1) Check if the connector CN304 on the LGC board is completely inserted or not disconnected. (2) Check if the connectors CN423 and CN424 on the IMG board and the connectors CN319 and CN320 on the LGC board are completely inserted. (3) Check if the connector pin between the IMG board (connector CN423, CN424) and the LGC board (connector CN319, CN320) is disconnected. (4) Check if the connector CN426 on the IMG board is completely inserted or not disconnected. (5) Check if the conductor patterns on the IMG board and the LGC board are short circuited or open circuited. (6) Replace the LGC board if no problem is found in steps from (1) to (5) above. (7) If the problem is not corrected with the replacement of the LGC board, reinstall the removed LGC board and replace the IMG board. (8) If the problem is still not corrected with the replacement of the IMG board, reinstall it and ask a specialist to repair it. (Abnormal ID) |
| Error code: | C970 |
| Description: | High-voltage transformer leakage abnormality: The high-voltage leakage of the main charger is detected. |
| Causes: | Main charger |
| Remedy: | (1) Is the main charger installed securely? (2) Check if the spring of high-voltage supply contact point is deformed. (3) Check if the main charger wire is broken or the main charger grid is deformed. (4) Check if any foreign matters is on the main charger win or the main charger grid. (5) Replace the High-voltage transformer. (6) Replace the LGC board. |
| Error code: | C9E0 |
| Description: | Connection error between SLG board and SYS board |
| Causes: | SLG board If the problem is not corrected with the replacement of the SLG board, reinstall the removed SLG board and replace the IMG board. IMG board If the problem is still not corrected with the replacement of the IMG board, reinstall the removed IMG board and replace the SYS board. SYS board |
| Remedy: | (1) Check if the connector CN12 on the SLG board is completely inserted or not disconnected. (2) Check if the connector CN421 on the IMG board is completely inserted or not disconnected. (3) Check if the connector pin between the SLG board (connector CN12) and the IMG board (connector CN421) is disconnected, or the harness connecting these boards is short circuited or open circuited. (4) Check if the connector CN422 on the IMG board and the connector CN135 on the SYS board are completely inserted. (5) Check if the connector pin between the IMG board (connector CN422) and the SYS board (connector CN135) is disconnected. (6) Check if the conductor patterns on the SLG board, IMG board and SYS board are short circuited or open circuited. (7) Replace the SLG board if no problem is found in steps from (1) to (6) above. (8) If the problem is not corrected with the replacement of the SLG board, reinstall the removed SLG board and replace the IMG board. (9) If the problem is still not corrected with the replacement of the IMG board, reinstall the removed IMG board and replace the SYS board. |
| Error code: | CA00 |
| Display: | Unusable Device Remove USB device. Turn the machine off and then back on again. Retry using a USB flash memory drive. |
| Description: | Image position alignment abnormality |
| Remedy: | < Invalidating image position alignment control > (1) Turn the power ON while [0] and [8] are pressed simultaneously. (2) Key in “4546”, then press the [START] button. (08-4546: Position adjustment control / Mode setting) (3) Set the value to “0” (not performed automatically). (4) Turn the power OFF. < Checking the abnormal status on image position alignment > (5) Turn the power ON while [0] and [5] are pressed simultaneously. (6) Key in “4720”, then press the [START] button. (7) Press the [START] button again, then check the displayed value. (05-4720-0: Displaying the cause of image position alignment detection error front and rear sides.) (8) Press the [START] button. (9) After [1] is pressed, then press the [START] button. (10) Check the displayed value. (05-4720-1: Displaying the cause of image position alignment detection error center side.) When the error [CA00] occurs, the value between 1 and 255 is displayed. (0: Detection normality on the front and rear sides) (The statues of total 8 sections (4 colors on the front and rear sides) are displayed.) 1 : Y on the rear side detection abnormality (*1) 2 : Y on the front side detection abnormality (*1) 3 : Y on the front and rear sides detection abnormality 4 : M on the rear side detection abnormality (*1) 8 : M on the front side detection abnormality (*1) 12 : M on the front and rear sides detection abnormality 16 : C on the rear side detection abnormality (*1) 32 : C on the front side detection abnormality (*1) 48 : C on the front and rear sides detection abnormality ) 64 : K on the rear side detection abnormality (*1) 85 : All colors on the rear side detection abnormality -> (I) 128: K on the front side detection abnormality (*1) 170: All colors on the front side detection abnormality -> (I) 192: K on the front and rear sides detection abnormality 255: All colors on the front and rear sides detection abnormality -> (I) Other than the above: Multiple colors detection abnormality (*2) The adjustment value is the sum of (*1), which, as in the example below, specifies the cause of the detection abnormality. (E.g. 1) 05-4720-0 --- in case of 72 72 = 64 + 8 -> K on the rear side / M on the front side detection abnormality (E.g. 2) 05-4720-0 --- in case of 146 146 = 128 + 18 = 128 + 16 + 2 -> K on the front side / C on the rear side / Y on the front side detection abnormality When the error [CA00] occurs, the value between 1 and 85 is displayed. (0: Detection normality on the center side) (The statues of total 4 sections (4 colors on the front and rear sides) are displayed.) 1 : Y on the center side detection abnormality (*3) 4 : M on the center side detection abnormality (*3) 16 : C on the center side detection abnormality (*3) 64 : K on the center side detection abnormality (*3) 85 : All colors on the center side detection abnormality -> (I) Other than the above: Multiple colors detection abnormality (*4) The adjustment value is the sum of (*3), which, as in the example below, specifies the cause of the detection abnormality. (E.g. 1) 05-4720-0 --- in case of 65 65 = 64 + 1 -> K on the rear side / Y on the front side detection abnormality |
| Error code: | CA10 |
| Description: | Polygonal motor abnormality: The polygonal motor does not run normally. |
| Causes: | Polygonal motor Laser unit cooling fan (front) Laser unit cooling fan (rear) LGC board Laser optical unit |
| Remedy: | Is the polygonal motor rotating? ↓ → NO → (e-STUDIO555/655) 1. Check if the connector CN209 on the PLG board is disconnected. 2. Check if the harness is open circuited and the connector pin is disconnected. 3. Check if the following signals are transmitted on the pins of the connector CN209 on the PLG board. Pin 1: 27±1V, Pin 2: GND, Pin 5: Less than or equal to 1V (Lo), Pin 4: Less than or equal to 0.7 V (Lo), Pin 3: Do not touch. 4. Check if the conductor pattern on the PLG board is short circuited or open circuited. 5. Replace the laser optical unit. 6. Replace the PLG board. (e-STUDIO755/855) 1. Check if the connector CN206 on the PLG board is disconnected. 2. Check if the harness is open circuited and the connector pin is disconnected. 3. Check if the following signals are transmitted on the pins of the connector CN206 on the PLG board. Pin 5: 24±1V, Pin 4: GND, Pin 3: Less than or equal to 1V (Lo), Pin 2: Less than or equal to 0.7 V (Lo), Pin 1: Do not touch. 4. Check if the conductor pattern on the PLG board is short circuited or open circuited. 5. Replace the laser optical unit. 6. Replace the PLG board. YES Is the deformed image output? ↓ → NO → (e-STUDIO555/655) 1. Check if the connector CN209 on the PLG board is about to be disconnected. 2. Check if the harness is about to be open circuited and the connector pin is disconnected. 3. Check if the following signals are transmitted on the pins of the connector CN209 on the PLG board. Pin 1: 27±1V, Pin 2: GND, Pin 5: Less than or equal to 1V (Lo), Pin 4: Less than or equal to 0.7 V (Lo), Pin 3: Do not touch. 4. Check if the conductor pattern on the PLG board is short circuited or open circuited. 5. Check if the laser unit cooling fan is not stopped. 6. Check if the intake area of the laser unit cooling fan is not blocked. 7. Replace the laser optical unit. 8. Replace the PLG board. (e-STUDIO755/855) 1. Check if the connector CN206 on the PLG board is about to be disconnected. 2. Check if the harness is about to be open circuited and the connector pin is disconnected. 3. Check if the following signals are transmitted on the pins of the connector CN206 on the PLG board. Pin 5: 24±1V, Pin 4: GND, Pin 3: Less than or equal to 1V (Lo), Pin 2: Less than or equal to 0.7 V (Lo), Pin 1: Do not touch. 4. Check if the conductor pattern on the PLG board is short circuited or open circuited. 5. Check if the laser unit cooling fan is not stopped. 6. Check if the intake area of the laser unit cooling fan is not blocked. 7. Replace the laser optical unit. 8. Replace the PLG board. YES 1. Check if the conductor pattern on the PLG board is short circuited or open circuited. 2. Check if the grounding wire of the high-voltage unit (e.g. developer unit, transfer unit) is grounded securely. 3. Check if the bias contact point of the high-voltage unit is contacted securely. (Check if the point is not stained either.) 4. Check if the metal plates of the transport system are grounded securely. 5. Check if the equipment is grounded securely? 6. Check if the laser unit cooling fan is not stopped. 7. Check if the intake area of the laser unit cooling fan is not blocked. 8. Replace the laser optical unit. |
| Error code: | CA20 |
| Description: | H-sync detection error: Laser beam cannot be detected at the SNS board. |
| Causes: | LGC board Laser optical unit |
| Remedy: | (e-STUDIO555/655) Is the harness connecting the connector (J207) on the PLG board and the connector on the LDR1 board open circuited? Are the connectors damaged or disconnected? Is the harness connecting the connector (CN202) on the PLG board and the connector on the SNS board open circuited? Are the connectors damaged or disconnected? (e-STUDIO755/855) Is the harness connecting the connector (J207) on the PLG board and the connector on the LDR1 board open circuited? Are the connectors damaged or disconnected? Is the harness connecting the connector (J208) on the PLG board and the connector on the LDR1 board open circuited? Are the connectors damaged or disconnected? Is the harness connecting the connector (J210) on the PLG board and the connector on the SNS board open circuited? Are the connectors damaged or disconnected? ↓ → NO → (e-STUDIO555/655) 1. Replace the harness. Reconnect the connector. 2. Check if the connector(J207) on PLG board hold the harness securely? 3. Check if the following signals are transmitted on the pin of the connector(CN1) on the PLG board? Pin 1: 5V, Pin 3: 0V 4. Replace the laser optical unit. (e-STUDIO755/855) 1. Replace the harness. Reconnect the connector. 2. Check if the connector(J207,J208) on PLG board hold the harness securely? 3. Replace the laser optical unit. YES 1. Check if the conductor pattern on the PLG board is short circuited or open circuited. 2. Check if the grounding wire of the high-voltage unit (e.g. developer unit, transfer unit) is grounded securely. 3. Check if the bias contact point of the high-voltage unit is contacted securely. (Check if the point is not stained either.) 4. Check if the metal plates of the transport system are grounded securely. 5. Check if the equipment is grounded securely? 6. Replace the laser optical unit. |
| Error code: | CB00 |
| Description: | Finisher not connected: Communication error has occurred between the equipment and finisher. [MJ1103/1104] |
| Causes: | Finisher control board. LGC board |
| Remedy: | MJ-1103/1104 1. Check if the MJ-1103/1104 is set as the specified finisher on the equipment. 2. Check if the harness connecting the converter PC board and the finisher controller PC board is disconnected or open circuited. 3. Check if the conductor pattern on the converter PC board is open circuited or short circuited. 4. Check if the conductor pattern on the finisher controller PC board is open circuited or short circuited. 5. Replace the converter PC board. 6. Replace the finisher control PC board. |
| Error code: | CB01 |
| Description: | Finisher communication error: Communication error has occurred between the equipment and finisher. [MJ-1103/1104] |
| Causes: | Finisher control board. LGC board |
| Remedy: | MJ-1103/1104 1. Check if the MJ-1103/1104 is set as the specified finisher on the equipment. 2. Check if the harness connecting the converter PC board and the finisher controller PC board is disconnected or open circuited. 3. Check if the conductor pattern on the converter PC board is open circuited or short circuited. 4. Check if the conductor pattern on the finisher controller PC board is open circuited or short circuited. 5. Replace the converter PC board. 6. Replace the finisher control PC board. |
| Error code: | CB10 |
| Description: | Feed motor abnormality: The feed motor does not run normally or the stack feed roller does not move normally. |
| Causes: | Entrance motor Finisher control board |
| Remedy: | [Procedure 1] Is second feed motor (M8) rotating in reverse at the fixed timing? → NO → Replace second feed motor or finisher controller PC board. YES Is the shutter securely attached to the shutter upper/lower bars? → NO → Attach it securely. YES Turn the feed roller-2 in reverse by hand. Do the shutter upper/lower bars move up and down? l → NO → Fix the mechanism including the shutter upper/lower bars and gears of the feed roller-2. YES Is the shutter closed detecting switch (MS4) working normally? → NO → Replace the switch. YES Replace the finisher controller PC board. [Procedure 2] Is second feed motor (M8) rotating in reverse at the fixed timing? → NO → Replace second feed motor or finisher controller PC board. YES Is the shutter securely attached to the shutter upper/lower bars? → NO → Attach it securely. YES Turn feed roller-2 in reverse by hand. Do the shutter upper/lower bars move up and down? l → NO → Fix the mechanism including the shutter upper/lower bars and gears of the feed roller-2. YES Is the shutter open sensor (PI5) working normally? → NO → Replace the sensor. YES Replace the finisher controller PC board. [Procedure 3] Check the safety zone switch (MS3). Is the switch working normally? → NO → Replace the switch. YES Is the safety zone switch (MS3) correctly pressed? → NO → Fix the mechanism. YES Is the shutter closed detecting switch (MS4) working normally? → NO → Replace the switch. YES Is the shutter closed detecting switch (MS4) correctly pressed? → NO → Fix the mechanism. YES Replace the finisher controller PC board. |
| Error code: | CB11 |
| Description: | Buffer tray guide motor abnormality: The buffer tray guide motor is not rotating or the buffer tray guide is not moving normally. [MJ-1103/1104] |
| Causes: | Buffer tray guide motor. Finisher control board |
| Remedy: | MJ-1103/1104 Is there any mechanical problem when the buffer tray guide is opened/closed while the buffer roller is lifted up? YES Fix the mechanism. NO Is the harness between the buffer tray guide motor (M3) and the finisher control PC board (CN18) disconnected or open circuited? l YES • Reconnect the connector securely. • Replace the harness. NO 1. Replace the buffer tray guide motor (M3). 2. Replace the finisher control PC board. |
| Error code: | CB12 |
| Description: | Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally. [MJ-1103/1104] |
| Causes: | Buffer roller drive motor Finisher control board |
| Remedy: | MJ-1103/1104 Is there any mechanical problem when the buffer roller is rotated? YES Fix the drive mechanism. NO Is the harness between the buffer roller drive motor (M6) and the finisher control PC board (CN18) disconnected or open circuited? l YES • Reconnect the connector securely. • Replace the harness. NO 1. Replace the buffer roller drive motor (M6). 2. Replace the finisher control PC board. |
| Error code: | CB13 |
| Description: | Finisher exit motor abnormality |
| Causes: | Exit motor. Finisher control board |
| Remedy: | Is there any mechanical problem when the exit roller is rotated? YES Fix the mechanism. NO Is the harness between the exit motor (M11) and the CN13 of the finisher control PC board (FIN) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO 1. Replace the exit motor (M11). 2. Replace the finisher control PC board (FIN). |
| Error code: | CB14 |
| Description: | Paper holding arm motor abnormality |
| Causes: | Assist arm motor Finisher control board |
| Remedy: | [CB14] Paper pusher arm motor (M10) abnormality Is there any mechanical problem when the paper pusher cam is rotated? YES Fix the drive mechanism. NO Is the harness between the assist arm motor (M10) and the CN13 of the finisher control PC board (FIN) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO 1. Replace the buffer roller drive motor (M10). 2. Replace the finisher control PC board (FIN). |
| Error code: | CB20 |
| Description: | Delivery motor abnormality: The delivery motor does not run normally or the delivery roller does not move normally. |
| Causes: | Exit motor clock sensor (PI10) Finisher controller circuit board Exit motor |
| Remedy: | Rotate the delivery motor by hand. Does it rotate smoothly? → NO → Fix the mechanism. YES Is the delivery motor clock sensor (PI10) working normally? → NO → Replace the sensor. YES MJ-1027/1028: Does the voltage between J11-4 and -5 on the finisher controller PC board become 24V when the delivery motor starts rotating? MJ-1029: Does the voltage between J11-1 and -2 on the finisher controller PC board become 24V when the delivery motor starts rotating? → NO → Replace the finisher controller PC board. YES Is the wiring between the delivery motor and finisher controller PC board correct? → YES → Correct the wiring. NO Replace the motor. |
| Error code: | CB30 |
| Description: | Tray lift motor abnormality |
| Causes: | Movable tray shift motor Movable tray position-A/-B/-C sensor Finisher control board |
| Remedy: | [Procedure 1] Is the tray 1 home position sensor (PI8) working properly? → NO → Replace the tray 1 home position sensor. YES Is the tray 1 lifting mechanism working properly? → NO → Correct the defect of the mechanism. YES Is 24V supplied to the tray1 lifting motor (M5) from the finisher control board at the timing of tray driving? → NO → Replace the finisher control board. YES Is the harness between the finisher control board and tray 1 lifting motor normal? → NO → Replace the harness. YES Replace the tray 1 lifting motor. [Procedure 2] Is the tray 1 lifted/lowered? ↓ → YES → Is the wiring between the finisher controller PC board and tray 1 lifting motor normal? → NO → Correct the wiring. YES Replace the tray 1 lifting motor. NO Is the power supplied to the motor from the finisher control board at the timing of tray 1 lifting? → NO → Replace the finisher control board. YES Correct the defect of the mechanism. [Procedure 3] Is the tray 2 home position sensor (PI25) working properly? → NO → Replace the tray 2 home position sensor. YES Is the tray 2 lifting mechanism working properly? → NO → Correct the defect of the mechanism. YES Is 24V supplied to the tray 2 lifting motor (M10) from the finisher control board at the timing of tray driving? → NO → Replace the finisher control board. YES Is the harness between the finisher control board and tray 2 lifting motor normal? → NO → Replace the harness. YES Replace the tray 2 lifting motor. [Procedure 4] Is the tray 2 lifted/lowered? ↓ → YES → Is the harness between the finisher control board and tray 2 lifting motor normal? → NO → Correct the wiring. YES Replace the tray 2 lifting motor. NO Is the power supplied to the motor from the finisher control board at the timing of tray 2 lifting? → NO → Replace the finisher control board. YES Is there any abnormality at the tray 2 lifting mechanism? → YES → Correct the defect of the mechanism. NO Replace the tray 2 lifting motor. [Procedure 5] Is the tray lifting mechanism working properly? → NO → Correct the defect of the mechanism. YES Is the tray coming close detection switch working properly? → NO → Replace the switch. YES Replace the finisher controller PC board. |
| Error code: | CB31 |
| Description: | Movable tray paper-full detection error: The actuator of the movable tray paper-full detection sensor does not move smoothly. [MJ-1103/1104] |
| Causes: | Movable tray paper-full detection sensor Movable tray position-A/-B/-C sensor Finisher control board |
| Remedy: | MJ-1103/1104 Is there any mechanical problem when the actuator of the movable tray paper-full detection sensor (S16) is moved? YES Fix the mechanism. NO Is there a disconnection of the connector, incorrect installation or breakage of the movable tray paper-full detection sensor (S16)? YES • Connect the connector securely. • Reinstall the sensor correctly. • Replace the sensor. NO Is the harness between the movable tray paper-full detection sensor (S16) and the finisher control PC board (CN12) disconnected or open circuited? l YES • Reconnect the connector securely. • Replace the harness. NO Replace the finisher control PC board. |
| Error code: | CB40 |
| Description: | Alignment motor (rear) abnormality: The alignment motor (rear) does not run normally or the alignment plate does not move normally |
| Causes: | Front alignment motor Finisher control board |
| Remedy: | Is the alignment guide home position sensor (PI6) working normally? → NO → Replace the sensor. YES Is the wiring between the finisher controller PC board and the alignment motor (M3) correct? → YES → Correct the wiring. NO Is there any mechanical problem with the alignment guide movement path? → YES → Fix the mechanism. NO Is the problem solved by replacing the alignment motor? → NO → Replace the finisher controller PC board. YES END |
| Error code: | CB50 |
| Description: | Staple motor abnormality: The staple motor does not run normally or the stapler does not move normally. |
| Causes: | Stapler Finisher control board |
| Remedy: | Is the wiring between the finisher controller PC board and the stapler normal? → NO → Correct the wiring. YES Is the problem solved by replacing the stapler? → YES → END NO Replace the finisher controller PC board. |
| Error code: | CB51 |
| Description: | Stapler shift home position error: The stapler is not at the home position. [MJ-1103/1104] |
| Causes: | Stapler Stapler unit home position sensor Stapler unit shift motor Finisher control board |
| Remedy: | MJ-1103/1104 Is there any mechanical problem when the stapler is moved? YES Fix the mechanism. NO Is there a disconnection of the connector, incorrect installation or breakage of the stapler unit home position sensor (S10)? YES • Connect the connector securely. • Reinstall the sensor correctly. • Replace the sensor. NO Is the harness between the stapler unit home position sensor (S10) and the finisher control PC board (CN1) disconnected or open circuited? l YES • Reconnect the connector securely. • Replace the harness. NO Is the harness between the stapler unit shift motor (M4) and the finisher control PC board (CN5) disconnected or open circuited? l YES • Reconnect the connector securely. • Replace the harness. NO Replace the finisher control PC board. |
| Error code: | CB60 |
| Description: | Stapler shift motor abnormality: The stapler shift motor does not run normally or the Staple Unit does not move normally. |
| Causes: | Stapler Stapler unit shift motor Finisher control board |
| Remedy: | Is the stapler shift home position sensor (PI7) working normally? → NO → Replace the sensor. YES Is the wiring between the finisher controller PC board and the stapler shift motor (M4) correct? → YES → Correct the wiring. NO Is there any mechanical problem with the stapler stand motion path? → YES → Fix the mechanism. NO Try replacing the staple shift motor. Is the problem corrected? → YES → END NO Replace the finisher controller PC board. |
| Error code: | CB80 |
| Description: | Backup RAM data abnormality: 1. Abnormality of checksum value on the finisher controller PC board is detected when the power is turned ON. 2. Abnormality of checksum value on the punch controller PC board is detected when the power is turned ON. |
| Causes: | Finisher control board |
| Remedy: | Is the problem solved by turning the power of the equipment OFF and ON? → YES → End. NO Replace the finisher controller PC board. Replace tha punch driver PC board. |
| Error code: | CB81 |
| Description: | Flash ROM abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON. [MJ-1103/1104] |
| Causes: | Finisher control board |
| Remedy: | MJ-1103/1104 Is the error recovered when the power of the equipment is turned OFF and then back ON? YES End. NO 1. Check if the conductor pattern on the finisher controller PC board is open circuited or short circuited. 2. Replace the finisher control PC board. |
| Error code: | CB82 |
| Description: | Finisher - Main CPU program error |
| Causes: | Finisher control board |
| Remedy: | 1. Update the firmware version of the finisher control PC board (FIN). 2. Replace the finisher control PC board (FIN). |
| Error code: | CB83 |
| Description: | Saddle Stitch Finisher - Main CPU program error |
| Causes: | Saddle control PC board |
| Remedy: | 1. Update the firmware version of the saddle control PC board (ADL). 2. Replace the saddle control PC board (SDL). |
| Error code: | CB84 |
| Description: | Hole Punch Unit - Main CPU program error |
| Causes: | Hole punch control PC board |
| Remedy: | Is the firmware version of the PNC board (HP) latest? YES Update the firmware of the PNC board (HP). NO Replace the hole punch control PC board (HP). |
| Error code: | CB91 |
| Description: | Saddle Stitch Finisher flash ROM abnormality |
| Causes: | Saddle controller PC board |
| Remedy: | Is the error recovered when the power of the equipment is turned OFF and then back ON? YES End. NO 1. Check if the conductor pattern on the saddle controller PC board (SDL) is open circuited or short circuited. 2. Replace the saddle control PC board (SDL). |
| Error code: | CB92 |
| Description: | Saddle Stitch Finisher RAM abnormality |
| Causes: | Saddle controller PC board |
| Remedy: | Is the error recovered when the power of the equipment is turned OFF and then back ON? YES End. NO Replace the Saddle control PC board (SDL). |
| Error code: | CB93 |
| Description: | Additional folding motor abnormality |
| Causes: | Additional folding motor Saddle control PC board |
| Remedy: | Is there any mechanical problem when the additional folding carrier is moved? YES Fix the mechanism. NO Is the harness between the additional folding motor (M20) and the CN18 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO 1. Replace the additional folding motor (M20). 2. Replace the saddle control PC board (SDL). |
| Error code: | CB94 |
| Description: | Saddle transport motor abnormality |
| Causes: | Saddle transport motor Saddle control PC board |
| Remedy: | Is there any mechanical problem when the transport rollers are rotated? YES Fix the mechanism. NO Is the harness between the saddle transport motor (M16) and the CN18 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO 1. Replace the saddle transport motor (M16). 2. Replace the saddle control PC board (SDL). |
| Error code: | CB95 |
| Description: | Stacker motor abnormality |
| Causes: | Stacker motor Saddle control PC board |
| Remedy: | Is there any mechanical problem when the stacker carrier is moved? YES Fix the mechanism. NO Is the harness between the stacker motor (M14) and the CN4 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the saddle control PC board (SDL). |
| Error code: | CBA0 |
| Description: | Stitch motor (front) abnormality: The stitch motor (front) does not run normally or the rotational cam does not move normally. |
| Causes: | Stitcher home position switch Stitcher motor Saddle control PC board |
| Remedy: | Are the front and rear stitchers and their stands installed properly? → NO → Install them properly. YES Are the stitcher home position switches (MS7S/MS5S) on the front and rear stitchers working normally? → NO → Replace the front or rear stitcher. YES Are the front and rear stitchers operating at the fixed timing? → NO → Replace the front or rear stitcher. YES Check the wiring between the stitcher and saddle stitcher controller PC board. If there is no problem, replace the controller PC board. |
| Error code: | CBB0 |
| Description: | Stitch motor (rear) abnormality: The stitch motor (rear) does not run normally or the rotational cam does not move normally. |
| Causes: | Stitcher home position switch Stitcher motor Saddle control PC board |
| Remedy: | Are the front and rear stitchers and their stands installed properly? → NO → Install them properly. YES Are the stitcher home position switches (MS7S/MS5S) on the front and rear stitchers working normally? → NO → Replace the front or rear stitcher. YES Are the front and rear stitchers operating at the fixed timing? → NO → Replace the front or rear stitcher. YES Check the wiring between the stitcher and saddle stitcher controller PC board. If there is no problem, replace the controller PC board. |
| Error code: | CBC0 |
| Description: | Alignment motor abnormality: The alignment motor does not run normally or the alignment plate does not move normally. |
| Causes: | Alignment plate home position sensor Alignment motor Saddle control PC board |
| Remedy: | Is the alignment plate home position sensor (PI5S) working normally? → NO → Replace the sensor. YES Is the alignment motor (M5S) operating at the fixed timing? → YES → Replace the saddle stitcher controller PC board. NO Is the alignment plate drive mechanism normal? → NO → Fix the mechanism. YES Is the problem solved by replacing the alignment motor (M5S)? → NO → Replace the saddle stitcher controller PC board. YES END |
| Error code: | CBE0 |
| Description: | Paper folding motor abnormality: The paper folding motor does not run normally or the paper folding roller does not move normally. |
| Causes: | Paper folding motor clock sensor Paper folding home position sensor Paper folding motor Saddle control PC board |
| Remedy: | Is the paper folding motor clock sensor (PI4S) working normally? → NO → Replace the sensor. YES Is the paper folding home position sensor (PI21S) working normally? → NO → Replace the sensor. YES Is the paper folding motor (M2S) operating at the fixed timing? → YES → Replace the saddle stitcher controller PC board. NO Is the paper folding roller drive mechanism normal? → NO → Fix the mechanism. YES Is the problem solved by replacing the paper folding motor (M2S)? → NO → Replace the saddle stitcher controller PC board. YES END |
| Error code: | CC20 |
| Description: | Communication error between Finisher and Saddle Stitch section: Communication error has occurred between the finisher controller PC board and the saddle stitcher controller PC board. |
| Causes: | Finisher control PC board Saddle control PC board |
| Remedy: | Is the problem solved by turning OFF and ON the power switch of the equipment? → YES → END NO Is the wiring between the finisher controller PC board and the saddle stitcher controller PC board connected? → YES → Connect the wiring. NO Measure the voltage between J3-2 (+) and J3-1 (-) on the finisher controller PC board. Is it DC 5V? → NO → Replace the finisher controller PC board. YES Replace the saddle stitcher controller PC board. |
| Error code: | CC30 |
| Description: | Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| Causes: | Stack transport motor Finisher control PC board |
| Remedy: | MJ-1103/1104 Is there any mechanical problem when the stack transport belt is moved? YES Fix the mechanism. NO Is the harness between the stack transport motor (M5) and the finisher control PC board (CN10) disconnected or open circuited? l YES • Reconnect the connector securely. • Replace the harness. NO 1. Replace the stack transport motor (M5). 2. Replace the finisher control PC board. |
| Error code: | CC31 |
| Description: | Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| Causes: | Transport motor Finisher control PC board |
| Remedy: | MJ-1103/1104 Is there any mechanical problem when the stack transport roller -1 and -2 are rotated? YES Fix the mechanism. NO Is the harness between the transport motor (M2) and the finisher control PC board (CN5) disconnected or open circuited? l YES • Reconnect the connector securely. • Replace the harness. NO 1. Replace the transport motor (M2). 2. Replace the finisher control PC board. |
| Error code: | CC41 |
| Description: | Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| Causes: | Paper holder home position sensor Finisher control PC board |
| Remedy: | MJ-1103/1104 Is there any mechanical problem when the paper holder cam is rotated? YES Fix the mechanism. NO Is the harness between the paper holder home position sensor (S6) and the finisher control PC board (CN17) disconnected or open circuited? l YES • Reconnect the connector securely. • Replace the harness. NO 1. Replace the paper holder home position sensor (S6). 2. Replace the finisher control PC board. |
| Error code: | CC51 |
| Description: | Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| Causes: | Sideways adjustment motor Sideways deviation home position sensor Hole punch control PC board |
| Remedy: | MJ-1103/1104 (When MJ-6102 is installed) Is there any paper remaining on the transport path? YES Remove the paper. NO Rotate the sideways adjustment motor (M2). Does it rotate smoothly? NO Fix the mechanism. YES Are the sideways deviation home position sensor (S3) and its wiring correct? NO Replace the sensor. Correct the wiring. YES Is the wiring between the hole punch control PC board (HP) and sideways adjustment motor (M2) correct? NO Correct the wiring. YES 1. Replace the punch sideways adjustment motor (M2). 2. Replace the hole punch control PC board (HP). |
| Error code: | CC52 |
| Description: | Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| Causes: | Skew adjustment motor Skew home position sensor Hole punch control PC board |
| Remedy: | MJ-1103/1104 (When MJ-6102 is installed) Is there any paper remaining on the transport path? YES Remove the paper. NO Rotate the skew adjustment motor (M1). Does it rotate smoothly? NO Fix the mechanism. YES Are the skew home position sensor (S2) and its wiring correct? NO Replace the sensor. Correct the wiring. YES Is the wiring between the hole punch control PC board (HP) and skew adjustment motor (M1) correct? NO Correct the wiring. YES 1. Replace the skew adjustment motor (M1). 2. Replace the hole punch control PC board (HP). |
| Error code: | CC61 |
| Description: | Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| Causes: | Punch motor Punch home position sensor Hole punch control PC board |
| Remedy: | MJ-1103/1104 (When MJ-6102 is installed) Is there any paper remaining on the transport path? YES Remove the paper. NO Rotate the punch motor (M3). Does it rotate smoothly? NO Fix the mechanism. YES Are the punch home position sensor (S4) and its wiring correct? NO Replace the sensor. Correct the wiring. YES Is the wiring between the hole punch control PC board (HP) and punch motor (M3) correct? NO Correct the wiring. YES 1. Replace the punch motor (M3). 2. Replace the hole punch control PC board (HP). |
| Error code: | CC71 |
| Description: | Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| Causes: | Hole punch control PC board |
| Remedy: | Download the latest version of the PNC board (HP) firmware again and then check its operation. NO Replace the hole punch control PC board (HP). |
| Error code: | CC72 |
| Description: | Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| Causes: | Hole punch control PC board |
| Remedy: | Download the latest version of the PNC board (HP) firmware again and then check its operation. NO Replace the hole punch control PC board (HP). |
| Error code: | CC80 |
| Description: | Rear alignment motor abnormality: The rear alignment motor is not rotating or the rear alignment plate is not moving normally. [MJ-1029] |
| Causes: | Rear alignment motor Finisher control PC board |
| Remedy: | Is the alignment guide home position sensor (PI29) working normally? → NO → Replace the sensor. YES Is the wiring between the finisher controller PC board and the alignment motor (M11) correct? → YES → Correct the wiring. NO Is there any mechanical problem with the alignment guide movement path? → YES → Fix the mechanism. NO Is the problem solved by replacing the alignment motor? → NO → Replace the finisher controller PC board. YES END |
| Error code: | CC90 |
| Description: | Upper stack tray lift motor abnormality: The upper stack tray lift motor is not rotating or the upper stack tray is not moving normally. Tray shift motor abnormality: The tray shift motor is not rotating or the stack tray is not moving normally. [MJ- 1031] |
| Causes: | Tray clock sensor (SR9) Tray lower limit sensor (SR5) Tray 500 sensor (SR4) Sensor controller PC board Finisher control PC board Tray shift motor (M2) |
| Remedy: | MJ-1031 Is the wiring between the finisher controller PC board and tray shift motor (M2) correct? NO Correct the wiring. YES Are the front and rear sides of the stack tray leveled? NO Level them. YES Is the tray clock sensor (SR9) working properly? NO Replace the sensor. YES Are the tray lower limit sensor (SR5), tray 500 sensor (SR4) and tray safety switch (SW2) working properly? NO Replace the sensor or sensor controller PC board. YES Does the voltage between the pins J114-1 and -2 on the finisher controller PC board become 24V when the tray shift motor starts rotating? NO Replace the finisher controller PC board. YES Check the wiring between the tray shift motor and finisher controller PC board. If there is no problem, replace the tray shift motor. |
| Error code: | CCB0 |
| Description: | Alignment motor (rear) abnormality: The alignment motor (rear) is not rotating normally or the rear alignment plate is not moving normally. [MJ-1025] Offset motor abnormality: The offset motor is not rotating normally. [MJ-1031] |
| Causes: | Offset HP sensor (SR1) Offset motor (M5) Finisher control PC board |
| Remedy: | MJ-1025 Is the aligning plate home position sensor (rear) (PI5) working properly? NO Replace the sensor. YES Is the wiring between the finisher controller PC board and aligning plate home position sensor (rear) correct? NO Correct the wiring. YES Is there any mechanical problem with the path of aligning plate? YES Fix the mechanism. NO Try replacing the alignment motor (rear) (M5). Is the problem corrected? YES End. NO Replace the finisher controller PC board. MJ-1031 1. Check if the connector J104 on the finisher controller PC board is disconnected from the offset HP sensor (SR1) or the harnesses are open circuited. Correct if any. 2. Check if the connector J107 on the finisher controller PC board is disconnected from the offset motor (M5) or the harnesses are open circuited. Correct if any. 3. Replace the offset HP sensor. 4. Replace the offset motor. 5. Replace the finisher control PC board. |
| Error code: | CCF1 |
| Description: | Tray safety switch abnormality - The tray safety switch turned on during tray operation (moving up or down). |
| Error code: | CD70 |
| Description: | Waste toner box mixing paddle locked: The mixing paddle in the waste toner box does not rotate. |
| Causes: | Waste toner box Waste toner paddle motor (M6) Waste toner paddle motor lock detection sensor (S14) LGC board |
| Remedy: | 1 Do the paddles in the waste toner box rotate? (Actually make them rotate.) Yes 2 No Replace the waste toner box. 2 Is the waste toner paddle motor (M6) rotating? (Perform the output check: 03-414) Yes 5 No 3 3 Waste toner paddle motor (M6) • Connector and relay connector check • Check if there is any damage or abnormality in the gears on the driving cascade of the waste toner paddle motor. 4 LGC board • Connector check (CN359) • Board check 5 Is the waste toner paddle motor lock detection sensor (S14) operating normally? (Perform output check: 03-[FAX] OFF/[1]/ [C]) * To judge an error, check if the sensor detects each status of normal display and highlighted display. Yes 7 No 6 6 Waste toner paddle motor lock detection sensor (S14) Connector and relay connector check 7 LGC board • Connector check (CN359) • Board check |
| Error code: | CD71 |
| Description: | Waste toner transport motor locking error: The auger in the waste toner transport path does not rotate. |
| Causes: | Waste toner transport motor Auger lock detection sensor EPU board LGC board |
| Remedy: | (1) Pull out the process unit, rotate the gear counterclockwise and check if the load is extremely heavy. (2) Is the load still extremely heavy after the gear is rotated for a while to discharge the toner from the waste toner transport path? (3) Is the load still extremely heavy after the actuator is removed, the auger is pulled out and clean them? (4) Check if there is any abnormality of the mechanism in the waste toner transport path. (5) Does the waste toner transport motor (M31) rotate? (Output check: 03-234) (6) Are the connector of the waste toner transport motor and the relay connector disconnected? (7) Is the driving gear of the waste toner transport motor damaged or abnormal? (8) Is the connector (CN331) on the LGC board disconnected? (9) Check if the connector pins are disconnected or the harnesses are open-circuited. (10) Check if the conductor pattern on the LGC board is short circuited or open circuited. (11) Replace the waste toner transport motor. (12) Replace the LGC board. (13) Are the auger lock detection sensor (S42) working? (Input check: 03-[FAX]ON/[0]/[B]) (14) Check if each Normal/Highlighted display is reflected correctly to judge the malfunction. (15) Is the connector of the auger lock sensor disconnected? (16) Is the connector (CN557) on the EPU board disconnected? (17) Check if the connector pins are disconnected, the EPU drawer connector pins are disconnected or bent or the harnesses are open-circuited. (18) Check if the conductor pattern on the EPU board is short circuited or open circuited. (19) Replace the auger lock detection sensor. (20) Replace the EPU board. (21) Check if there is any abnormality of the mechanism such as the sensor`s actuator. |
| Error code: | CD72 |
| Description: | Waste toner motor locking error ("Waste toner box replacement"): "Waste toner box replacement" appears when either CD70 or CD71 error occurs. The error code CD72 is noted on the error history and logs. |
| Causes: | Waste toner box |
| Remedy: | 1 Waste toner box Replace it according to the displayed instruction. Notes: If you close the access cover without replacing the waste toner box, a message prompting you to turn the power OFF and then back ON appears, followed by CD70 or CD71. Replace the waste toner box first to check if CD70 or CD71 is cleared. If not, follow the troubleshooting procedure for CD70 or CD71. 2 Power supply unit Turn the power OFF and then back ON according to the displayed instruction. 3 CD70 or CD71 display Follow the troubleshooting procedure for CD70 or CD71. |
| Error code: | CDE0 |
| Description: | Paddle motor abnormality: The paddle motor is not rotating or the paddle is not rotating normally. [MJ-1029] |
| Causes: | Paddle motor |
| Remedy: | Is the paddle home position sensor (PI26) working normally? → NO → Replace the sensor. YES Is the wiring between the finisher controller PC board and the paddle motor (M14) correct? → YES → Correct the wiring. NO Is the paddle drive mechanism normal? → YES → Fix the mechanism. NO Is the problem solved by replacing the paddle motor? → NO → Replace the finisher controller PC board. YES END |
| Error code: | CE00 |
| Description: | Communication error between finisher and punch unit: Communication error between finisher controller PC board and punch controller PC board [MJ-1103/1104 (when MJ-6102 is installed)] |
| Causes: | Hole punch control PC board Finisher control PC board |
| Remedy: | Download the latest version of the PNC board (HP) firmware again and then check its operation. NO Replace the hole punch control PC board (HP). |
| Error code: | CE10 |
| Description: | Image quality sensor abnormality (OFF level): The output value of this sensor is out of a specified range when sensor light source is OFF. |
| Causes: | Image quality sensor Switching regulator LGC board |
| Remedy: | Is the connector of the image quality sensor, or the connector CN307 on the LGC board disconnected? Is the harness between the LGC board and the image quality sensor, or the harness between the LGC board and the switching power supply open circuited? YES Connect the connector securely. Replace the harness. NO Is the output voltage from the 12V-power supply normal? NO Check the power supply system and replace the switching power supply. YES 1. Replace the image quality sensor. 2. Replace the LGC board. |
| Error code: | CE20 |
| Description: | Image quality sensor abnormality (no pattern level): The output value of this sensor is out of a specified range when the image quality control test pattern is not formed. |
| Causes: | Image quality sensor |
| Remedy: | Are there any abnormal stains (cleaning defects), large scratches or breaking on the transfer belt surface? Are the drum and the transfer belt rotating? NO <Checking procedure> 1. Check if the transfer belt unit is securely installed. Correct it if not. 2. Check if any toner image remains on the transfer belt surface. If any, check the installation status of the TBU cleaner unit. If there is any abnormality, correct it, and clean the transfer belt. 3. Check if the drum and the transfer belt are properly operated. (ON: 03-101 / OFF: 03-151) If they are not rotating normally, check if their drive gears are damaged or if they contact the equipment. Correct it if needed. Proceed to step (6). (to step (1) for the second time) YES Is the sensor shutter of the image quality sensor opening or closing normally? Or is it damaged? Is the sensor surface of the image quality sensor stained with toner? If so, has it been cleaned? NO <Checking procedure> 1. Take off the transfer belt unit so that you can see the sensor unit. 2. Check if the sensor shutter is opening or closing normally. (Opening: 03-118 / Closing: 03-168) If the sensor shutter is not opening or closing, check if it is damaged or there is any abnormality in the sensor shutter solenoid. Check the connector and the harness between the sensor shutter solenoid and the LGC board. (LGC CN307-A7pin, A8pin) 3. Slide the sensor shutter so that the sensor surface can be seen. 4. Clean the sensor surface with a cotton swab or a soft cloth. 5. Clean the area around the sensor (e.g.: sensor shutter) if it is stained, so that the sensor surface does not become dirty. Proceed to step (6). (to step (1) for the second time) YES Is the connector of the image quality sensor securely connected? Is the connector CN307 on the LGC board securely connected? Is the harness between the LGC board and the image quality sensor disconnected? NO <Checking procedure> • Reconnect the connector. • Replace the harness. Proceed to step (6). (to step (1) for the second time) YES Is +12V power supply voltage normally supplied to the image quality sensor? Is +12V voltage normally output by the CN301-9pin on the LGC board? NO <Checking procedure> 1. Check if +12V voltage is output by the switching power supply (PS-ACC CN404-7pin). 2. Check if +12V voltage is output by the CN301-9pin on the LGC board. Check if the supply harness between the switching power supply and the LGC board is open circuited, damaged or disconnected. Proceed to step (6). (to step (1) for the second time) YES (1) Set the values of “Image quality closed-loop control / Contrast voltage (08-556)” and “Drum surface potential sensor control setting (08-2561)” to “0” (Invalid). (2) Perform “Enforced performing of image quality open-loop control (05-394)”. (3) Output the image quality control test pattern (04-270) more than one time and the list print ([9][START]) in the adjustment mode (05), and then check if the image is normal. Normal Abnormal Abnormal image: Blank print, Solid print, White banding, Color banding, White spots, Poor transfer, Uneven image density, Faded image (low density), Uneven light distribution, Blotched image. * Blank print: including when one of the YMCK colors is not printed. Correct the abnormal image. Proceed to step (5). (4) Replace the image quality sensor or the LGC board. (5) Set the values of “Image quality closed-loop control / Contrast voltage (08-556)” and “Drum surface potential sensor control setting (08-2561)” to “1” (Valid). (6) Perform “Automatic initialization of image quality control (05-396)” and make sure it is completed normally. (Error [CE10], [CE20] and [CE40] do not appear.) Then perform “Automatic gamma adjustment”. | When an error occurs: Check and correct it accordingly. (7) Reset all of the values in the codes “Abnormality detection count (Y/M/C/K) Display/0 clearing (08-573 to 08-576)”. |
| Error code: | CE40 |
| Description: | Image quality control test pattern abnormality: The test pattern is not formed normally. |
| Remedy: | (1) Use “Image quality control abnormal detection counter Y to K display/0 clearing (08-573 to 576)” to check the abnormal occurring condition for each color. (2) Check “Output value display of image quality sensor / High-density pattern (05-390-0 to 3)” to check if the high-density pattern abnormality occurs for each color and identify the color which pattern is abnormal. If the value is 628 or above, it is defined as high-density pattern abnormality. High-density pattern abnormality • Check if the laser shutter is working properly. <Procedure> 1. Take off the process unit so that the laser shutter can be easily seen. * Clean around the laser shutter if the developer has been spilled over. 2. While pressing the digital keys [0] and [3] simultaneously, turn the power ON. 3. Key in “201”. 4. Press the [START] button and check if the shutter is opened and then closed (reciprocating 1cycle). • Check if the developer unit has been installed properly. 1. Visually check the installation status of the developer unit, and correct it if there is any abnormality. | To (8) (If you have already performed this checking cycle once, proceed to step (3).) (3) Set the values of “Image quality closed-loop control / Contrast voltage (08-556)” and “Drum surface potential sensor control setting (08-2561)” to “0” (Invalid). (4) Perform “Enforced performing of image quality open-loop control (05-394)”. (5) Output the image quality control test pattern (04-270) more than one time and the list print ([9][START]) in the adjustment mode (05), and check the patch of the color identified in step (1) to see if the image is abnormal Abnormal image: Blank print, Solid print, White banding, Color banding, White spots, Poor transfer, Uneven image density, Faded image (low density), Uneven light distribution, Blotched image. * Blank print: including when one of the YMCK colors is not printed. Correct the abnormal image. Proceed to step (7). (6) Replace the image quality sensor or LGC board. (7) Set the values of “Image quality closed-loop control / Contrast voltage (08-556)” and “Image quality closed-loop control / Laser power (08-557)” to “1” (Valid). (8) Perform “Automatic initialization of image quality control (05-396)” and make sure it is completed normally. (Error [CE40] does not appear.) Then perform “Automatic gamma adjustment”. (9) Clear all “Image quality control abnormal detection counter Y to K display/0 clearing (08-573 to 576)”. (10) Check if any of the springs for supplying power to the transfer belt unit is deformed. Replace the spring if it is deformed. |
| Error code: | CE50 |
| Description: | Temperature/humidity sensor abnormality: The output value of the temperature/humidity sensor is out of the specified range. |
| Causes: | Temperature/humidity sensor LGC board |
| Remedy: | Is the connector CN338 on the LGC board or the connector of the temperature/humidity sensor (S7) disconnected? Is the harness between the LGC board and the temperature/humidity sensor disconnected? → YES → Connect the connector securely. Replace the harness. NO 1. Check the connection of the KEY board and DSP board. 2. Check the connection of the DSP board and LGC board. 3. Replace the temperature/humidity sensor. 4. Replace the LGC board. |
| Error code: | CE60 |
| Description: | Drum thermistor-Y abnormality: The output value of the drum thermistor-Y is out of a specified range. |
| Causes: | Drum thermistor-K Drum thermistor-Y EPU board LGC board |
| Remedy: | (1) Check if there is any abnormality on the connector between the equipment and the EPU tray of the process unit. (05-2788) (2) Is the harness between the LGC board and the drawer connector for developer unit disconnected? (3) Is the harness inside of the developer unit and the harness of the drum thermistor Y or K disconnected? (4) Is the connector CN341 on the LGC board, or the connector of the drum thermistor Y or K disconnected? (5) Replace the drum thermistor Y or K. (6) Replace the EPU board. (7) Replace the LGC board. |
| Error code: | CE70 |
| Description: | Drum drive switching abnormality: The drum switching detection sensor (S11) is not turned ON after the drum motor was rotated for a specified period of time. |
| Causes: | Drum switching motor (M3) Drum switching detection sensor (S11) LGC board |
| Remedy: | 1 Is the drum switching motor (M3) operating properly? (Perform the output check: 03-240) Yes 5 No 2 2 Drum switching motor (M3) Check the connector of the motor and joint connectors 3 Drum switching detection sensor (S11) Sensor check 4 LGC board • Connector check (CN391, CN392) • Board check 5 Is the drum switching detection sensor (S11) working? (Perform the input check: 03-[ALL]OFF/[8]/ [F] (Highlighted in the black mode)) Yes 8 No 6 6 Drum switching detection sensor (S11) • Sensor, connector, joint connector check • Check if there is any foreign matter such as grease in the detection area of the drum switching detection sensor. 7 LGC board • Connector check (CN391, CN392) • Board check 8 Is the drum switching motor assembled in the drum drive unit able to be rotated smoothly by hand? Yes 10 No 9 9 Drum switching motor (M3) • While reinstalling the drum switching motor, push it so that its gear will slightly move away from the engaging gear. • Check the bracket in which the drum switching motor is installed. If it is deformed, replace it. 10 Is the drum switching guide able to be moved smoothly by hand after the drum switching motor has been removed? Yes 12 No 11 11 Drum switching motor (M3) Check if the slide area (guide, plate) of the drum switching guide is deformed or any foreign matter is attached to it. (Replace it if there is.) 12 LGC board Board check |
| Error code: | CE71 |
| Description: | Drum phase adjustment abnormality: Drum phase sensors (Color drum phase sensor and K drum phase sensor) are not turned ON after the drum motor was rotated for a specified period of time. |
| Causes: | Drum motor (K) Drum motor (YMC) K drum phase sensor Color drum phase sensor LGC board Cleaning blade (Y, M, C, K) Needle electrode Drum (Y, M, C, K) |
| Remedy: | (1) Is the drum shaft rotating normally? (Perform the output check: 03-110 and 03-111) (2) Check if the harness or connector of the color drum phase sensor or the K drum phase senor is disconnected or open-circuited. (3) Is the drum loaded abnormally? (4) Is the drum motor (K)/(YMC) broken? (5) Check if the harness or connector of the drum motor (K)/(YMC) is disconnected or opencircuited. (6) Check if the tooth surface of the transfer belt drive gear is damaged. |
| Error code: | CE90 |
| Description: | Drum thermistor abnormality: The output value of the drum thermistor is out of the specified range. |
| Causes: | Drum thermistor-K Drum thermistor-Y EPU board LGC board |
| Remedy: | Is the connector CN337 on the LGC board, or the connector of the drum thermistor disconnected? Is the harness between the LGC board and the drum thermistor (THM5) disconnected? → YES → Connect the connector securely. Replace the harness. NO 1. Replace the drum thermistor. 2. Replace the LGC board. |
| Error code: | CEC1 |
| Description: | 2nd transfer roller contacting position detection abnormality |
| Causes: | Registration motor (M19) LGC board 2nd transfer roller position detection sensor (S29) |
| Remedy: | 1 Is the 2nd transfer roller`s contact and release proper? (Perform output check: 03-239) Yes 4 No 2 2 Registration motor (M19) • Connector check • Harness check 3 LGC board • Connector check (CN332) • Board check 4 Is the 2nd transfer roller position detection sensor (S29) working properly? (Perform input check: 03-[ALL]OFF/[7]/[E]) Yes 7 No 5 5 2nd transfer roller position detection sensor (S29) • Connector and relay connector check • Harness check 6 LGC board • Connector check (CN337) • Board check 7 Mechanical section Sensor check 8 LGC board Board check |
| Error code: | CEC2 |
| Description: | 2nd transfer roller releasing position detection abnormality |
| Causes: | Registration motor (M19) LGC board One-way clutch gear at the end of the shaft 2nd transfer roller position detection sensor (S29) |
| Remedy: | 1 Is the 2nd transfer roller`s contact and release proper? (Perform output check: 03-239) Yes 9 No 2 2 Is the registration motor (M19) rotating? Yes 5 No 3 3 Registration motor (M19) • Connector check • Harness check 4 LGC board • Connector check (CN332) • Board check 5 Is the 2nd transfer roller holding arm operated smoothly when it is pushed? Yes 8 No 6 6 2nd transfer roller pressure spring Check that the spring is installed properly (not running off the frame of the mold). 7 Parts surrounding the 2nd transfer roller Check if there is any damage or abnormality. 8 One-way clutch gear at the end of the shaft Replace it. 9 Is the 2nd transfer roller position detection sensor (S29) working properly? (Perform input check: 03-[ALL]OFF/[7]/[E]) Yes No 10 10 LGC board • Connector and relay connector check • Harness check 11 Parts surrounding the 2nd transfer roller • Connector check (CN337) • Board check 12 Mechanical section Sensor check 13 LGC board Board check |
| Error code: | CF10 |
| Description: | Undefined error code processing: If the engine of the equipment judges that a code (command) other than the defined error codes is sent from the finisher, it regards this as a CF10 error. |
| Causes: | Finisher control PC board Hole punch control PC board (when MJ-6102 is installed) |
| Remedy: | (1) Is the error recovered when the power of the equipment is turned OFF and then back ON? (2) If not as in step 1, check if the LGC board and IPC board are connected correctly. (3) If the error has still not been recovered in step 2, check if there is any defect in the LGC board, IPC board or finisher control board. If not, replace the LGC board, IPC board or finisher control board. |
| Error code: | CF90 |
| Description: | Laser optical unit shutter abnormality. |
| Causes: | Shutter motor Shutter sensor (home position) Shutter sensor (end position) LGC board |
| Remedy: | 1. Take off the left center cover so that the connector relay plate and the shutter motor can be seen. 2. Is the shutter motor working? (Perform the output check: 03-201). * If it is working properly, proceed to 10. If not, check 3 to 9 below. 3. Check if the shutter motor connector CN214 (2-pin connector) is disconnected. 4. Check if the connector CN218 (8-pin connector) on the connector relay plate is disconnected. 5. Check if the connector CN327 on the LGC board is disconnected. 6. Check if the connector pins are disconnected or the harnesses are open circuited. 7. Check if the conductor pattern on the LGC board is short circuited or open circuited. 8. Replace the shutter motor. 9. Replace the LGC board. 10.Is the shutter motor working and the shutter plate moving? (Perform the output check: 03-201) * If it is working properly, proceed to 14. If not, check 11 to 13 below. 11. Check if the shutter motor and the shutter crank are assembled correctly, or not damaged. 12. Check if the shutter plate is assembled correctly. 13.Check if the shutter plate contacts with any parts inside the machine. 14.Is the shutter motor working, and the shutter plate reciprocates one cycle to stop at its original position. * If it is working properly, proceed to 25. If not, check 15 to 24 below. 15.Perform the input check for the shutter detection sensor (Perform the input check: 03-[All OFF]/ [7]/[D] and /[E]). 16.Manually move the shutter to see that it is “opened” when the crank is in the front, and it is “closed” when the crank is in the back. Therefore, check if the sensor detects as described in the table below. Abnormal H H Open H L Close L H Midstream L L 17.Check if the detection sensor is coming off of or lift off from the plate base. 18.Check if the connector of the shutter status detection sensor (CN216, CN217) are disconnected. 19.Check if the detection sensor cut-out part of the shutter plate is deformed. 20.Check if the connector (CN327) on the LGC board disconnected. 21.Check if the connector pins are disconnected or the harnesses are open-circuited. 22.Check if the conductor pattern on the LGC board is open-circuited or short-circuited. 23.Replace the shutter status detection sensor. 24.Replace the LGC board. 25.Take off the LSU and check if there is no foreign matter between the shutter plate and the LSU cover. 26.Check if the conductor pattern on the LGC board is open-circuited or short-circuited. 27.Check the LGC board |
| Error code: | E010 |
| Display: | E010 |
| Description: | Paper not reaching fuser transport sensor: Paper which has passed the fuser unit does not reach the fuser transport sensor. |
| Causes: | Fuser transport sensor LGC board ADU board PFC board Fuser unit |
| Remedy: | Open the jam access cover. Is there any paper on the transport path or in the fuser unit? → YES → Remove the paper. NO Is the fuser transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[7]/[C]) ↓ → NO → 1. Check if the connector of the fuser transport sensor is disconnected. 2. Check if the connector CN332 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the fuser transport sensor. 6. Replace the LGC board. YES Is the transfer belt working? ↓ → NO → 1. Check if the connector of the transport belt is disconnected. 2. Check if the connector on the transport motor driving PC board is disconnected. 3. Check if the connector CN341 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the transport motor driving PC board. 7. Replace the LGC board. YES Is the drum separation finger solenoid working? (Perform the output check in the test mode: 03-111,161) ↓ → NO → 1. Check if the connector of the drum separation finger solenoid is disconnected. 2. Check if the connector CN339 on the LGC board is disconnected. 3. Check the installation state of cleaner. 4. Is the relay connector connecting the cleaner unit and the equipment disconnected or stained with toner? 5. Replace the drum separation finger solenoid. 6. Replace the LGC board. YES Is the registration sensor working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the registration sensor is installed correctly. 3. Check if the registration actuator is operating properly. 4. Check if the connector CN341 on the LGC board is disconnected. 5. Check if the connector pins are disconnected and the harnesses are open circuited. 6. Check if the conductor pattern on the LGC board is short circuited or open circuited. 7. Replace the registration sensor. 8. Replace the LGC board. YES Is the registration motor working? (Perform the output check in the test mode: 03-108/158) ↓ → NO → 1. Check if the connector of the registration roller clutch is disconnected. 2. Check if the connector CN341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration roller clutch. 6. Replace the LGC board. YES Check if there is any abnormality in the space between the registration motor and the registration roller (metal). Check if the registration roller (rubber) is rotating smoothly. Check the condition of the registration roller at the horizontal transport section and clean or replace it. * If the error [E010] caused by a paper jam underneath the drum cleaner often occurs due to an insufficient paper separation from the photoconductive drum, set a smaller value in the code 08-841, and see what happens. At this time, however, pay attention to the transferability at the leading edge of the paper since this transferability can be slightly narrowed depending on the environments and conditions under which the equipment is placed or the media type of the paper used. (Refer to 3.6.1 in this manual about the details of the code 08-841.) |
| Error code: | E011 |
| Description: | Transfer belt paper-clinging jam: The paper after the 2nd transfer is clinging to the transfer belt, or a paper jam occurred between the registration roller and the paper clinging detection sensor. |
| Causes: | Paper clinging detection sensor Registration motor PFC board LGC board Rollers |
| Remedy: | 1. Check if there is any paper clinging to the transfer belt or entering under the receiving tray. Remove it if there is. 2. Use the paper within the specification if the thin paper being used is out of specification. 3. Is the registration motor rotating? (Perform the input check. 03-128/528) 4. Check if the connector CN512 on the PFC board is disconnected from the registration motor or the harnesses are open circuited. Correct if any. 5. Replace the registration motor. 6. Replace the PFC board. 7. Check the state of the registration roller and replace it if it is deteriorated. 8. Is the paper clinging detection sensor working? (Perform the input check: 03-[FAX]OFF/[7]/[E]) 9. Check if the connector CN307 on the LGC board is disconnected from the paper clinging detection sensor or the harnesses are open circuited. Correct if any. 10.Replace the paper clinging detection sensor. 11.Is the transfer belt rotating normally? (Perform the output check: 03-116) 12.Is the transfer belt cleaning blade peeled? 13.Is the auger of the transfer belt cleaner unit locked? 14.Is the connector of the transfer belt motor disconnected? 15.Is the transfer belt motor broken? 16.Check if the tooth surface of the transfer belt drive gear is damaged. 17.Replace the PFC board. 18.Use the paper within the specification if the special paper whose reflection rate is lower than the specification is used. 19.If jams occur on the back side in duplex printing, change the media type mode to the recycled paper mode, and then check if there are still jams. (When this type of jam occurs on heavily curled paper during duplex printing, the jam may be resolved by selecting the recycled paper mode.) 20.Change the 2nd transfer bias offset value as shown below and then check if there are still jams. Change the default value 5 of each code below to 6 or 7. Color: 05-2935 Subcode: 7 Black: 05-2937 Subcode: 7 |
| Error code: | E020 |
| Description: | Paper stopping at fuser transport sensor: The trailing edge of paper does not pass the fuser transport sensor after its leading edge has reached the fuser transport sensor. |
| Causes: | LGC board ADU board PFC board Rollers |
| Remedy: | Is the fuser transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[7]/[C]) ↓ → NO → 1. Check if the connector of the fuser transport sensor is disconnected. 2. Check if the connector CN332 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the fuser transport sensor. 6. Replace the LGC board. YES Is the reverse motor driving? (Perform the output check in the test mode: 03-126) ↓ → NO → 1. Check if the connector of the reverse transport unit is not disconnected. 2. Check if the connector CN335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check if the conductor pattern on the LGC board is not short- or open-circuited. 5. Replace the LGC board YES 1. Check if the separation finger for the fuser unit is working normally. 2. Replace the LGC board |
| Error code: | E030 |
| Description: | Power-ON jam: Paper is remaining on the paper transport path of the equipment when the power is turned ON. |
| Causes: | Fuser transport sensor LGC board ADU board PFC board Rollers |
| Remedy: | Open the cover of the unit/area whose picture is blinking on the control panel. Is there any paper on the transport path? (Refer to the following table.) → YES → Remove the paper. NO Is the sensor in the jamming area working? (Perform the input check in the test mode: refer to the following table.) ↓ → NO → 1. Check if the connector of the sensor is disconnected. 2. Check if any of the connectors on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the sensor. 6. Replace the LGC board. YES Replace the LGC board. Registration area Registration sensor 03-[FAX]ON/[4]/[E] Exit/Reverse area Exit sensor 03-[FAX]OFF/[7]/[B] Reverse sensor-1 03-[FAX]OFF/[7]/[E] Reverse sensor-2 03-[FAX]OFF/[7]/[D] Fuser transport sensor 03-[FAX]OFF/[7]/[C] Reverse transport area Horizontal transport sensor-1 03-[FAX]OFF/[9]/[F] Horizontal transport sensor-2 03-[FAX]OFF/[9]/[G] Horizontal transport sensor-3 03-[FAX]OFF/[9]/[H] Paper feeding area 1st drawer feed sensor 03-[FAX]OFF/[1]/[D] 2nd drawer feed sensor 03-[FAX]OFF/[2]/[D] 3rd drawer / tandem LCF feed sensor 03-[FAX]OFF/[3]/[D] 4th drawer feed sensor 03-[FAX]OFF/[4]/[D] 1st drawer transport sensor 03-[FAX]OFF/[1]/[C] 2nd drawer transport sensor 03-[FAX]OFF/[2]/[C] 3rd drawer / tandem LCF transport sensor 03-[FAX]OFF/[3]/[C] 4th drawer transport sensor 03-[FAX]OFF/[4]/[C] Intermediate transport sensor 03-[FAX]OFF/[1]/[A] |
| Error code: | E061 |
| Description: | Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment. |
| Remedy: | If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON. |
| Error code: | E062 |
| Description: | Incorrect paper size setting for 2nd drawer: The size of paper in the 2nd drawer differs from size setting of the equipment. |
| Remedy: | If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON. |
| Error code: | E063 |
| Description: | Incorrect paper size setting for 3rd drawer: The size of paper in the 3rd drawer differs from size setting of the equipment. |
| Remedy: | If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON. |
| Error code: | E064 |
| Description: | Incorrect paper size setting for 4th drawer: The size of paper in the 4th drawer differs from size setting of the equipment. |
| Remedy: | If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON. |
| Error code: | E065 |
| Display: | E065 error X motor |
| Description: | Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment. |
| Remedy: | If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON. |
| Error code: | E090 |
| Description: | Image data delay jam: Image data to be printed cannot be prepared. |
| Causes: | SYS board IMG board LGC board HDD Page memory |
| Remedy: | 1. Remove the paper remained in front of the registration sensor. 2. If the error still occurs, check the following: 3. Check if the error is cleared by turning the power OFF and then back ON. 4. Check if the connectors connecting the SYS board, SLG board and PLG board are disconnected. 5. Check if the connectors of the HDD are disconnected. 6. Check if the page memory is connected to the connector on the SYS board properly. 7. Replace the page memory. 8. Check if the harnesses connecting the SYS board, SLG board and PLG board are opencircuited. 9. Replace the HDD, SYS board, SLG board and PLG board. |
| Error code: | E091 |
| Description: | Other time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware. |
| Causes: | SYS board IMG board LGC board HDD |
| Remedy: | 1. Check if there is any paper in the equipment. Remove it if there is. 2. If the error still occurs, check the following: 3. Check if the error is cleared by turning the power OFF and then back ON. 4. Check if the connectors connecting the SYS board, SYSIF board, SLG board and PLG board are disconnected. 5. Check if the connectors of the HDD are disconnected. 6. Check if the page memory is connected to the connector on the SYS board properly. 7. Replace the page memory. 8. Check if the harnesses connecting the SYSIF board, SLG board and PLG board are opencircuited. 9. Replace the HDD, SYS board, SLG board and PLG board. |
| Error code: | E0A0 |
| Description: | Image transport ready time-out jam: Image data to be printed cannot be sent. |
| Causes: | SYS board IMG board LGC board HDD |
| Remedy: | 1. Remove the paper remained in front of the registration sensor. 2. Check if the error is cleared by turning the power OFF and then back ON. 3. Check if the connector CN341 on the LGC board is disconnected. 4. Replace the LGC board. |
| Error code: | E110 |
| Description: | Transport jam during duplex printing (paper not reaching registration sensor): Paper which passed the reverse transport section does not reach the registration sensor during duplex printing. |
| Causes: | Registration sensor ADU motor2 ADU board PFC board LGC board ADU roller |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the registration sensor? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Is the transport motor (M17) rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. YES Check the transport roller. Clean or replace it. (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → If the paper is damaged, remove the paper and check the followings. 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ll → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) NO → Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. Replace the registration roller(rubber) if not solved. |
| Error code: | E120 |
| Description: | Bypass misfeeding (paper not reaching registration sensor): Paper fed out of the bypass tray does not reach the registration sensor. |
| Causes: | Bypass feed sensor Bypass motor Bypass pick-up solenoid ADU board PFC board ADU roller Rollers |
| Remedy: | Open the bypass unit cover. Is there any paper in front of the registration sensor? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Is the width of the side guides of the bypass unit too narrow? Is the paper skewed? → YES → Match the width of the side guides and that of the paper. NO Is the bypass feed clutch working? (Perform the output check in the test mode: 03-204) Is the bypass feed sensor working? (Perform the input check in the test mode: 03- [FAX]OFF/[6]/[G]) ↓ → NO → 1. Check if the connector of the bypass feed clutch and bypass feed sensor are disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the bypass feed clutch and bypass feel sensor. 6. Replace the LGC board. YES Check the bypass transport roller, feed separation and separation rollers. Clean or replace them. |
| Error code: | E130 |
| Description: | 1st drawer misfeeding (paper not reaching 1st drawer feed sensor): Paper does not reach the 1st drawer feed sensor during the feeding at the 1st drawer. |
| Causes: | 1st drawer feed sensor Feed motor PFC roller Rollers |
| Remedy: | Open the feed cover. Is there any paper in front of the 1st drawer transport sensor? → YES → Remove the paper. NO Is the 1st drawer feed sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[D]) ↓ → NO → 1. Check if the connector of the 1st drawer feed sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer feed sensor. 6. Replace the LGC board. YES Is the width of the side guides of the 1st drawer too narrow? Is there any paper skewing? → YES → Fit the width of the original guide to that of the paper. NO Is the 1st drawer feed clutch working? (Perform the output check in the test mode: 03-201) ↓ → NO → 1. Check if the connector of the 1st drawer feed clutch is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer feed clutch. 6. Replace the LGC board. YES Check the 1st drawer feed roller, separation roller and pickup roller. Clean or replace them. * Check if the paper weight is within the specified range. |
| Error code: | E140 |
| Description: | 2nd drawer misfeeding (paper not reaching 2nd drawer feed sensor): Paper does not reach the 2nd drawer feed sensor during the feeding at the 2nd drawer. |
| Causes: | 2nd drawer feed sensor Feed motor PFC roller Rollers |
| Remedy: | Open the drawer feed cover. Is there any paper in front of the 2nd drawer transport sensor? → YES → Remove the paper. NO Is the 2nd drawer transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[D]) ↓ → NO → 1. Check if the connector of the 2nd drawer feed sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 2nd drawer feed sensor. 6. Replace the LGC board. YES Is the width of the side guides of the 2nd drawer too narrow? Is there any paper skewing? → YES → Fit the width of the original guide to that of the paper. NO Is the 2nd drawer feed clutch working? (Perform the output check in the test mode: 03-202) ↓ → NO → 1. Check if the connector of the 2nd drawer feed clutch is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 2nd drawer feed clutch. 6. Replace the LGC board. YES Check the 2nd drawer feed roller, separation roller and pickup roller. Clean or replace them. * Check if the paper weight is within the specified range. |
| Error code: | E150 |
| Description: | 3rd drawer misfeeding (paper not reaching 3rd drawer / Tandem LCF feed sensor): Paper does not reach the 3rd drawer / Tandem LCF feed sensor during the feeding at the 3rd drawer. |
| Causes: | 3rd drawer feed sensor Feed/transfer motor PFC roller Rollers 3rd drawer feed clutch |
| Remedy: | Open the feed cover. Is there any paper in front of the 3rd drawer / Tandem LCF feed sensor? → YES → Remove the paper. NO Is the 3rd drawer / Tandem LCF feed sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[3]/[D]) ↓ → NO → 1. Check if the connector of the 3rd drawer / Tandem LCF feed sensor is disconnected. 2. Check if the connector CN328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 3rd drawer / Tandem LCF feed sensor. 6. Replace the LGC board. YES Is the width of the side guides of the 3rd drawer too narrow? Is there any paper skewing? → YES → Fit the width of the original guide to that of the paper. NO Is the 3rd drawer / Tandem LCF feed clutch working? (Perform the output check in the test mode: 03-209 (Tandem LCF model) and 03-226 (4th drawer model)) ↓ → NO → 1. Check if the connector of the 3rd drawer / Tandem LCF feed clutch is disconnected. 2. Check if the connector CN328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 3rd drawer / Tandem LCF feed clutch. 6. Replace the LGC board. YES Check the 3rd drawer / Tandem LCF feed roller, separation roller and pickup roller. Clean or replace them. * Check if the paper weight is within the specified range. |
| Error code: | E160 |
| Description: | 4th drawer misfeeding (paper not reaching 4th drawer feed sensor): Paper does not reach the 4th drawer feed sensor during the feeding at the 4th drawer. |
| Causes: | 4th drawer feed sensor Feed/transfer motor PFC roller Rollers 4th drawer feed clutch |
| Remedy: | Open the feed cover. Is there any paper in front of the 4th drawer feed sensor? → YES → Remove the paper. NO Is the 4th drawer feed sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[4]/[D]) ↓ → NO → 1. Check if the connector of the 4th drawer feed sensor is disconnected. 2. Check if the connector CN350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 4th drawer feed sensor. 6. Replace the LGC board. YES Is the width of the side guides of the 4th drawer too narrow? Is there any paper skewing? → YES → Fit the width of the original guide to that of the paper. NO Is the 4th drawer feed clutch working? (Perform the output check in the test mode: 03-228) ↓ → NO → 1. Check if the connector of the 4th drawer feed clutch is disconnected. 2. Check if the connector CN350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 4th drawer feed clutch. 6. Replace the LGC board. YES Check the 4th drawer feed roller, separation roller and pickup roller. Clean or replace them. * Check if the paper weight is within the specified range. |
| Error code: | E190 |
| Description: | Tandem LCF misfeeding (paper not reaching 3rd drawer / Tandem LCF feed sensor): Paper does not reach the 3rd drawer Tandem LCF feed sensor during the feeding at the Tandem LCF. |
| Causes: | LCF feed sensor LCF feed clutch PFC board Rollers |
| Remedy: | Open the feed cover. Is there any paper in front of the 3rd drawer / Tandem LCF feed sensor? → YES → Remove the paper. NO Is the 3rd drawer / Tandem LCF feed sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[3]/[D]) ↓ → NO → 1. Check if the connector of the 3rd drawer / Tandem LCF feed sensor is disconnected. 2. Check if the connector CN328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 3rd drawer / Tandem LCF feed sensor. 6. Replace the LGC board. YES Is the width of the side guides of the 3rd drawer too narrow? Is there any paper skewing? → YES → Fit the width of the original guide to that of the paper. NO Is the 3rd drawer / Tandem LCF feed clutch working? (Perform the output check in the test mode: 03-209 (Tandem LCF model) and 03-226 (4th drawer model)) ↓ → NO → 1. Check if the connector of the 3rd drawer / Tandem LCF feed clutch is disconnected. 2. Check if the connector CN328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 3rd drawer / Tandem LCF feed clutch. 6. Replace the LGC board. YES Check the 3rd drawer / Tandem LCF feed roller, separation roller and pickup roller. Clean or replace them. * Check if the paper weight is within the specified range. |
| Error code: | E200 |
| Description: | 1st drawer transport jam (paper not reaching registration sensor): Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the 1st drawer. |
| Causes: | Registration sensor Transport motor-1 PFC board LGC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the registration sensor? → YES → Replace the paper. NO Is the registration sensor(S18) working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES 1. Check the transport roller. Replace it if it is worn out. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor (S17) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor (M17) rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. 7. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. Check if the registration roller (rubber) is rotating smoothly. |
| Error code: | E210 |
| Description: | 2nd drawer transport jam (paper not reaching registration sensor): Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the 2nd drawer. |
| Causes: | Registration sensor Transport motor-1 PFC board LGC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the registration sensor? → YES → Replace the paper. NO Is the registration sensor(S18) working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES 1. Check the transport roller. Replace it if it is worn out. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor (S17) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor (M17) rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. 7. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. Check if the registration roller (rubber) is rotating smoothly. |
| Error code: | E220 |
| Description: | 2nd drawer transport jam (paper not reaching 1st drawer transport sensor): Paper which has passed the 2nd drawer transport sensor does not reach the 1st drawer transport sensor during the feeding at the 2nd drawer. |
| Causes: | 1st drawer transport sensor Transport motor-2 Transport motor-1 PFC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the 1st drawer transport sensor? → YES → Remove the paper. NO Is the 1st drawer transport sensor (S33) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[C]) ↓ → NO → 1. Check if the connector of the 1st drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches (CLT5,7,9,11) working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings: 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E270 |
| Description: | Bypass transport jam (Paper not reaching the registration sensor): Paper fed from the bypass tray and passed through the bypass feed sensor does not reach the registration sensor. |
| Causes: | Registration sensor Transport motor-1 PFC board LGC board Rollers |
| Remedy: | 1. Open the jam access cover and check if there is any paper in front of the 1st drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 1st drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[1]/[G]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN516 on the PFC board is disconnected from the 1st drawer feed sensor or the harnesses are open circuited. Correct if any. 4. Replace the 1st drawer feed sensor. 5. Replace the PFC board. 6. Is the transport motor-1 working? (Perform the output check: 03-124 or 524) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connector CN512 on the PFC board is disconnected from the transport motor-1 or the harnesses are open circuited. Correct if any. 8. Replace the transport motor-1. 9. Replace the PFC board. 10.Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 11.Check the transport roller. Replace it if it is worn out. |
| Error code: | E300 |
| Description: | 3rd drawer transport jam (paper not reaching registration sensor): Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the 3rd drawer. |
| Causes: | Registration sensor Transport motor-1 PFC board LGC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the registration sensor? → YES → Replace the paper. NO Is the registration sensor(S18) working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES 1. Check the transport roller. Replace it if it is worn out. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor (S17) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor (M17) rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. 7. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. Check if the registration roller (rubber) is rotating smoothly. |
| Error code: | E310 |
| Description: | 3rd drawer transport jam (paper not reaching 1st drawer transport sensor): Paper which has passed the 2nd transport sensor does not reach the 1st drawer transport sensor during the feeding at the 3rd drawer. |
| Causes: | 1st drawer transport sensor Transport motor-2 Transport motor-1 PFC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the 1st drawer transport sensor? → YES → Remove the paper. NO Is the 1st drawer transport sensor (S33) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[C]) ↓ → NO → 1. Check if the connector of the 1st drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches (CLT5,7,9,11) working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings: 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E320 |
| Description: | 3rd drawer transport jam (paper not reaching 2nd drawer transport sensor): Paper which has passed the 3rd drawer / Tandem LCF transport sensor does not reach the 2nd drawer transport sensor during the feeding at the 3rd drawer. |
| Causes: | 3rd drawer transport clutch 2nd drawer transport sensor Feed motor PFC board Rollers |
| Remedy: | Open the feed cover. Is there paper in front of the 2nd drawer transport sensor? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the 2nd drawer transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[C] ↓ → NO → 1. Check if the connector of the 2nd drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 2nd drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-210/225/231) ↓ → NO → 1. Check if the connectors of the (lower/middle) transport clutches are disconnected. 2. Check if the connector CN329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the (lower/middle) transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. |
| Error code: | E330 |
| Description: | 4th drawer transport jam (paper not reaching registration sensor): Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the 4th drawer. |
| Causes: | Registration sensor Transport motor-1 PFC board LGC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the registration sensor? → YES → Replace the paper. NO Is the registration sensor(S18) working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES 1. Check the transport roller. Replace it if it is worn out. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor (S17) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor (M17) rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. 7. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. Check if the registration roller (rubber) is rotating smoothly. |
| Error code: | E340 |
| Description: | 4th drawer transport jam (paper not reaching 1st transport sensor): Paper which has passed the 2nd drawer transport sensor does not reach the 1st drawer transport sensor during the feeding at the 4th drawer. |
| Causes: | 1st drawer transport sensor Transport motor-2 Transport motor-1 PFC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the 1st drawer transport sensor? → YES → Remove the paper. NO Is the 1st drawer transport sensor (S33) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[C]) ↓ → NO → 1. Check if the connector of the 1st drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches (CLT5,7,9,11) working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings: 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E350 |
| Description: | 4th drawer transport jam (paper not reaching 2nd drawer transport sensor): Paper which has passed the 3rd drawer / Tandem LCF transport sensor does not reach the 2nd drawer transport sensor during the feeding at the 4th drawer. |
| Causes: | 3rd drawer transport clutch 2nd drawer transport sensor Feed motor PFC board Rollers |
| Remedy: | Open the feed cover. Is there paper in front of the 2nd drawer transport sensor? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the 2nd drawer transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[C] ↓ → NO → 1. Check if the connector of the 2nd drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 2nd drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-210/225/231) ↓ → NO → 1. Check if the connectors of the (lower/middle) transport clutches are disconnected. 2. Check if the connector CN329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the (lower/middle) transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. |
| Error code: | E360 |
| Description: | 4th drawer transport jam (paper not reaching 3rd drawer / Tandem LCF transport sensor): Paper which has passed the 4th drawer transport sensor does not reach the 3rd drawer / Tandem LCF transport sensor during the feeding at the 4th drawer. |
| Causes: | 4rd drawer transport clutch 3rd drawer transport sensor 3rd drawer transport clutch Feed motor PFC board Rollers |
| Remedy: | Open the feed cover. Is there any paper in front of the 3rd drawer / Tandem LCF feed sensor? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the 3rd drawer / Tandem LCF feed sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[D]) ↓ → NO → 1. Check if the connector of the 3rd drawer / Tandem LCF feed sensor is disconnected. 2. Check if the connector CN328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the LGC board is short circuited or open circuited. 5. Replace the 3rd drawer / Tandem LCF drawer feed sensor. 6. Replace the LGC board. YES Is the 4th drawer transport clutch working? (Perform the output check in the test mode: 03-225) ↓ → NO → 1. Check if the connector of the 4th drawer transport clutch is disconnected. 2. Check if the connector CN350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 4th drawer transport clutch. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the PFP transport roller. Clean or replace it. |
| Error code: | E3C0 |
| Description: | Tandem LCF transport jam (paper not reaching registration sensor): Paper which has passed the 1st transport sensor does not reach the registration sensor during the feeding at the Tandem LCF. |
| Causes: | Registration sensor Transport motor-1 PFC board LGC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the registration sensor? → YES → Replace the paper. NO Is the registration sensor(S18) working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES 1. Check the transport roller. Replace it if it is worn out. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor (S17) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor (M17) rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. 7. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. Check if the registration roller (rubber) is rotating smoothly. |
| Error code: | E3D0 |
| Description: | Tandem LCF transport jam (paper not reaching 1st drawer transport sensor): Paper which has passed the 2nd drawer transport sensor does not reach the 1st drawer transport sensor during the feeding at the Tandem LCF. |
| Causes: | 1st drawer transport sensor Transport motor-2 Transport motor-1 PFC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the 1st drawer transport sensor? → YES → Remove the paper. NO Is the 1st drawer transport sensor (S33) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[C]) ↓ → NO → 1. Check if the connector of the 1st drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches (CLT5,7,9,11) working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings: 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E3E0 |
| Description: | Tandem LCF transport jam (paper not reaching 2nd transport sensor): Paper which has passed the 3rd drawer / Tandem LCF transport sensor does not reach the 2nd drawer transport sensor during the feeding at the Tandem LCF. |
| Causes: | 3rd drawer transport clutch 2nd drawer transport sensor Feed motor PFC board Rollers |
| Remedy: | Open the feed cover. Is there paper in front of the 2nd drawer transport sensor? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the 2nd drawer transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[C] ↓ → NO → 1. Check if the connector of the 2nd drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 2nd drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-210/225/231) ↓ → NO → 1. Check if the connectors of the (lower/middle) transport clutches are disconnected. 2. Check if the connector CN329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the (lower/middle) transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. |
| Error code: | E400 |
| Display: | Print Unable E4 Turn the power off and then back on again. |
| Description: | Duplexing unit open jam |
| Causes: | Fuse LGC board Switching regulator Interlock switch |
| Remedy: | 1. Close the duplexing unit if it is opened. Remove if there is any paper before closing it. 2. Is the voltage of 24V being supplied from the power supply unit? (Perform the input check: 03- [COPY] ON/[6]/[A]) 3. Check if the connector CN309 on the LGC board is disconnected from the connector CN403 on the switching regulator or the harnesses are open circuited. Correct if any. 4. Check if the fuse (F201, F202, F203, and F204) on the switching regulator has blown. 5. Replace the PFC board. 6. Replace the switching regulator. 7. Is the interlock switch working properly? (Perform the input check: 03-[SCAN] ON/[4]/[G]) 8. Check if the connector CN312 on the LGC board is disconnected from the interlock switch or the harnesses are open circuited. Correct if any. |
| Error code: | E410 |
| Description: | Front cover open jam: The front cover has opened during printing. |
| Causes: | Front cover opening/closing switch LGC board |
| Remedy: | Is the front cover open? → YES → Remove the paper if there is any, then close the cover. NO Is the voltage of 24V being supplied from the power supply unit? (Perform the input check in the test mode: 03-[FAX] ON/[9]/[H]) ↓ → NO → 1. Check if the connector for 24 V power supply is disconnected. 2. Check if the connector CN344 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Replace the LGC board. |
| Error code: | E420 |
| Description: | PFP side cover open jam: The PFP side cover has opened during printing. |
| Causes: | PFP side cover opening/closing switch PFP board LGC board |
| Remedy: | 1 Is the PFP side cover open? Yes Remove the paper if there is any, then close the cover. No 2 2 Is the PFP side cover opening/closing switch working? (Perform the input check in the test mode: 03- [FAX]OFF/[2]/[A]) Yes 3 No • Check if the connector of the PFP side cover opening/closing switch is disconnected. • Check if either of the connectors CN241 or CN243 on the PFP board is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. • Replace the PFP side cover opening/ closing switch. • Replace the PFP board. • Replace the LGC board. 3 Replacing board • Replace the PFP board. • Replace the LGC board. |
| Error code: | E430 |
| Description: | ADU open jam: The ADU has opened during printing. |
| Causes: | ADU opening/closing switch ADU board LGC board |
| Remedy: | 1. Close the ADU if it is opened. Remove if there is any paper before closing it. 2. Is the ADU opening/closing switch working? (Perform the input check: 03-[FAX]ON/[2]/[C]) 3. Check if the connector CN338 on the LGC board is disconnected from the ADU opening/closing switch or the harnesses are open circuited. Check if the connectors CN211 and CN217 on the ADU board are disconnected. Correct if any. 4. Replace the ADU opening/closing switch. 5. Replace the ADU board. 6. Replace the PFC board. 7. Replace the LGC board. |
| Error code: | E440 |
| Description: | Right lower cover (feed cover) open jam: The feed cover has opened during printing. |
| Causes: | ADU opening/closing switch LGC board |
| Remedy: | Is the feed cover open? → YES → Remove the paper if there is any, then close the cover. NO Is the side door switch working? (Perform the input check in the test mode: 03-[FAX]ON/[2]/[A]) ↓ → NO → 1. Check if the connector of the feed cover sensor is disconnected. 2. Check if the connector CN304 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the feed cover sensor. 6. Replace the LGC board. YES Replace the LGC board. |
| Error code: | E450 |
| Description: | Option LCF side cover open jam: The side cover of the Option LCF has opened during printing. |
| Causes: | LCF side cover opening/closing switch LCF board LGC board |
| Remedy: | Is the LCF front cover open? → YES → Remove the paper if there is any, then close the cover. NO Is the LCF side cover opening/closing switch working? (Perform the input check in the test mode: 03-[FAX]OFF/[5]/[B]) ↓ → NO → 1. Check if the connector of the LCF side cover opening/closing switch is disconnected. 2. Check if either of the connectors CN100 or CN106 on the LCF board is disconnected. 3. Check if the connector CN338 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 6. Replace the LCF side cover opening/closing switch. 7. Replace the LCF board. 8. Replace the LGC board. YES 1. Replace the LCF board. 2. Replace the LGC board. |
| Error code: | E480 |
| Description: | Bridge unit open jam: The bridge unit has opened during printing. |
| Causes: | Bridge unit cover opening/closing detection switch LGC board |
| Remedy: | 1. Close the bridge unit if it is opened. Remove if there is any paper before closing it. 2. Is the bridge unit cover opening/closing detection switch working? (Perform the input check: 03- [FAX]OFF/[5]/[E]) 3. Check if the connector CN334 on the LGC board is disconnected from the bridge unit cover opening/closing detection switch or the harnesses are open circuited. Correct if any. 4. Replace the bridge unit cover opening/closing detection switch. 5. Replace the LGC board. |
| Error code: | E4A0 |
| Description: | Waste toner cover open jam (printing) |
| Causes: | Waste toner detection sensor LGC board |
| Remedy: | 1. Close the waste toner cover if it is opened. Remove if there is any paper before closing it. 2. Is the waste toner detection sensor working? (Perform the input check: 03-[FAXON]/[1]/[C]) 3. Check if the connector CN331 on the LGC board is disconnected from the waste toner detection sensor or the harnesses are open circuited. Correct if any. 4. Replace the waste toner detection sensor. 5. Replace the LGC board. |
| Error code: | E510 |
| Description: | Transport jam during duplex printing (paper not reaching reverse sensor-2): Paper which has passed the reverse sensor-1 does not reach the reverse sensor-2 during duplex printing. |
| Causes: | Duplexing unit path entrance sensor Reverse motor ADU motor-2 PFC board ADU board DRV board Rollers |
| Remedy: | Open the exit cover. Is there any paper in front of the reverse sensor-2? → YES → Remove the paper. NO Is the reverse sensor-1 working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[G]) ↓ → NO → 1. Check if the connector of the reverse sensor-1 is disconnected. 2. Check if the connector CN335 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on LGC board are short circuited or open circuited. 5. Replace the reverse sensor-1. 6. Replace the LGC board. YES Is the horizontal transport section driving clutch working? (Perform the output check in the test mode: 03-222) ↓ → NO → 1. Check if the connector of the horizontal transport section driving clutch is disconnected. 2. Check if the connector CN334 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the horizontal transport section driving clutch. 6. Replace the LGC board. YES Is the Mylar at the reverse section normal? → NO → Replace the Mylar. YES Check the condition of the roller at the horizontal transport section and clean or replace it. |
| Error code: | E520 |
| Description: | Stop jam in the ADU: The paper does not reach the ADU exit sensor after it has passed the ADU entrance sensor. |
| Causes: | ADU exit sensor LGC board ADU exit sensor MOT board MOT2 board Rollers in the ADU |
| Remedy: | 1 Open the ADU. Is there any paper in front of the ADU exit sensor? Yes Remove the paper. No 2 2 Is the ADU exit sensor working? (Perform the input check in the test mode: 03- [FAX]OFF/[1]/[E]) Yes 3 No • Check if the connector of the ADU exit sensor is disconnected. • Check if the connector CN311 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the LGC board are short circuited or open circuited. • Replace the ADU exit sensor. • Replace the LGC board. 3 Is the ADU motor working? (Perform the output check in the test mode: 03-119) Yes 4 No • Check if the connector of the ADU motor is disconnected. • Check if the connector CN402 and CN404 on the MOT/MOT2 board is disconnected. • Check if the connector CN303 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the ADU exit sensor. • Replace the MOT/MOT2 board. • Replace the LGC board. 4 ADU • Check the rollers in the ADU. Replace them if they are worn out. |
| Error code: | E550 |
| Description: | Paper remaining jam at paper transport path: Paper is remaining on the paper transport path when the printing has finished. (Jam caused by a multiple paper feeding) |
| Causes: | Feed or transport roller possibly causing multiple feeding Sensor in the jamming area Refer to the table below PFC board |
| Remedy: | Open the cover of the unit/area whose picture is blinking on the control panel. Is there any paper on the transport path? → YES → Remove the paper. NO Is the sensor in the jamming area working? (Perform the input check in the test mode: refer to the following table) ↓ → NO→ 1. Check if the connector of the sensor is disconnected. 2. Check if any of the connectors on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the sensor. 6. Replace the LGC board. YES 1. Check if any multiple paper is fed from the drawer. 2. Replace the LGC board. Registration area Registration sensor 03-[FAX]ON/[4]/[E] Exit/Reverse area Exit sensor 03-[FAX]OFF/[7]/[B] Reverse sensor-1 03-[FAX]OFF/[7]/[E] Reverse sensor-2 03-[FAX]OFF/[7]/[D] Fuser transport sensor 03-[FAX]OFF/[7]/[C] Reverse transport area Horizontal transport sensor-1 03-[FAX]OFF/[9]/[F] Horizontal transport sensor-2 03-[FAX]OFF/[9]/[G] Horizontal transport sensor-3 03-[FAX]OFF/[9]/[H] Paper feeding area 1st drawer feed sensor 03-[FAX]OFF/[1]/[D] 2nd drawer feed sensor 03-[FAX]OFF/[2]/[D] 3rd drawer / tandem LCF feed sensor 03-[FAX]OFF/[3]/[D] 4th drawer feed sensor 03-[FAX]OFF/[4]/[D] 1st drawer transport sensor 03-[FAX]OFF/[1]/[C] 2nd drawer transport sensor 03-[FAX]OFF/[2]/[C] 3rd drawer / tandem LCF transport sensor 03-[FAX]OFF/[3]/[C] 4th drawer transport sensor 03-[FAX]OFF/[4]/[C] Intermediate transport sensor 03-[FAX]OFF/[1]/[A] |
| Error code: | E551 |
| Description: | Paper remaining jam on the transport path (when a service call occurs) |
| Causes: | Feed or transport roller possibly causing multiple feeding Sensor in the jamming area Refer to the table below. LGC board |
| Remedy: | 1 Jamming transport path Open the cover of the unit/area whose picture is flashing on the control panel and remove any paper on the transport path. 2 Sensor in the jamming area • Sensor check (Refer to the table below) • Harness check • Connector check 3 LGC board • Harness check • Connector check • Board check Notes: If the jam is occurring in the ADU, LCF or PFP, check the board in each unit. Registration area Jam access cover Registration sensor 03-[ALL]OFF/[9]/[A] Paper clinging detection sensor 03-[ALL]OFF/[9]/[E] Registration pass sensor 03-[ALL]OFF/[9]/[F] Feed sensor 03-[ALL]OFF/[9]/[B] Exit area Fuser cover Exit sensor 03-[ALL]OFF/[9]/[C] ADU ADU ADU entrance sensor 03-[ALL]OFF/[9]/[G] ADU exit sensor 03-[ALL]OFF/[9]/[H] Bypass feed unit Side cover 2nd drawer feed sensor 03-[FAX]ON/[4]/[D] LCF LCF side cover LCF feed sensor 03-[COPY]ON/[9]/[F] PFP PFP side cover PFP upper drawer feed sensor 03-[FAX]ON/[0]/[C] PFP lower drawer feed sensor 03-[FAX]ON/[0]/[D] Bridge unit Bridge unit Bridge unit transport sensor-1 (Entrance sensor) 03-[ALL]OFF/[0]/[A] Bridge unit transport sensor-2 (Exit sensor) 03-[ALL]OFF/[0]/[B] Finisher Finisher door Sensors in the finisher |
| Error code: | E552 |
| Description: | Paper remaining jam on the transport path (when the cover is closed) |
| Causes: | Feed or transport roller possibly causing multiple feeding Sensor in the jamming area Refer to the table below. LGC board |
| Remedy: | 1 Jamming transport path Open the cover of the unit/area whose picture is flashing on the control panel and remove any paper on the transport path. 2 Sensor in the jamming area • Sensor check (Refer to the table below) • Harness check • Connector check 3 LGC board • Harness check • Connector check • Board check Notes: If the jam is occurring in the ADU, LCF or PFP, check the board in each unit. Registration area Jam access cover Registration sensor 03-[ALL]OFF/[9]/[A] Paper clinging detection sensor 03-[ALL]OFF/[9]/[E] Registration pass sensor 03-[ALL]OFF/[9]/[F] Feed sensor 03-[ALL]OFF/[9]/[B] Exit area Fuser cover Exit sensor 03-[ALL]OFF/[9]/[C] ADU ADU ADU entrance sensor 03-[ALL]OFF/[9]/[G] ADU exit sensor 03-[ALL]OFF/[9]/[H] Bypass feed unit Side cover 2nd drawer feed sensor 03-[FAX]ON/[4]/[D] LCF LCF side cover LCF feed sensor 03-[COPY]ON/[9]/[F] PFP PFP side cover PFP upper drawer feed sensor 03-[FAX]ON/[0]/[C] PFP lower drawer feed sensor 03-[FAX]ON/[0]/[D] Bridge unit Bridge unit Bridge unit transport sensor-1 (Entrance sensor) 03-[ALL]OFF/[0]/[A] Bridge unit transport sensor-2 (Exit sensor) 03-[ALL]OFF/[0]/[B] Finisher Finisher door Sensors in the finisher |
| Error code: | E712 |
| Description: | Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor. |
| Causes: | Original registration sensor Original pickup solenoid RADF board Perform the 05-3210 Roller Pickup roller, feed roller, separation roller |
| Remedy: | 1. Clean the pickup roller, feed roller and separation roller if they are stained. 2. Flatten the original if it is folded or excessively curled and place it again. 3. Is the original registration sensor working? (Perform the input check: 03-[FAX]ON/[7]/[H]) * If it is working properly, proceed to 7. If not, check 3 to 6. 4. Check if the connector CN74 on the RADF board is disconnected from the original registration sensor or the harnesses are open circuited. Correct if any. 5. Replace the original registration sensor. 6. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 7. Replace the pickup roller, feed roller and separation roller if they are worn out. |
| Error code: | E714 |
| Description: | Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray. |
| Causes: | Original empty sensor RADF board Perform the 05-3210 Roller Pickup roller, feed roller, separation roller |
| Remedy: | 1. Is the original empty sensor working? (Perform the input check: 03-[FAX]ON/[7]/[B]) 2. Check if the lever of original empty sensor is working normally. 3. Check if the connector CN74 on the RADF board is disconnected from the original empty sensor or the harnesses are open circuited. Correct if any. 4. Replace the original empty sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). |
| Error code: | E721 |
| Description: | Jam not reaching the original reading start sensor: The original does not reach the original reading start sensor after it has passed the original registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side). |
| Causes: | Original reading start sensor RADF board Perform the 05-3210 Roller Registration roller, Read roller |
| Remedy: | 1. Clean the original registration roller, intermediate transfer roller, reading start roller, reverse roller and reverse registration roller if they are stained. 2. Is the original reading start sensor working? (Perform the input check: 03-[FAX]ON/[7]/[G]) * If it is working properly, proceed to 8. If not, check 3 to 7 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original reading start sensor or the harnesses are open circuited. Correct if any. 4. Perform the automatic adjustment of the original reading start sensor (05-356). 5. Perform the manual adjustment of the original reading start sensor. 6. Replace the original reading sensor, and then perform the automatic adjustment of the original reading start sensor (05-356). 7. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 8. Replace the original registration roller, intermediate transfer roller, reading start roller, reverse roller and reverse registration roller if they are worn out. |
| Error code: | E722 |
| Description: | Jam not reaching the original exit sensor (during scanning): The original which passed the read sensor does not reach the original exit sensor when it is transported from the scanning section to exit section. |
| Causes: | Original exit sensor RADF board Perform the 05-3210 Roller |
| Remedy: | 1. Clean the reading end roller and the exit intermediate roller if they are stained. 2. Is the original exit sensor working? (Perform the input check: 03-[FAX]ON/[7]/[E]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original exit sensor or the harnesses are open circuited. Correct if any. 4. Replace the original exit sensor 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Replace the reading end roller and the exit intermediate roller if they are worn out. |
| Error code: | E724 |
| Description: | Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor. |
| Causes: | Original registration sensor RADF board Perform the 05-3210 Roller |
| Remedy: | 1. Clean the original registration roller if it is stained. 2. Is the original registration sensor working? (Perform the input check: 03-[FAX]ON/[7]/[H]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN74 on the RADF board is disconnected from the original registration sensor or the harnesses are open circuited. Correct if any. 4. Replace the original registration sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Replace the original registration roller if it is worn out. |
| Error code: | E725 |
| Description: | Stop jam at the reading start sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor. |
| Causes: | Original reading start sensor RADF board Perform the 05-3210 Roller Registration roller, Read roller |
| Remedy: | 1. Clean the original registration roller, intermediate transfer roller, reading start roller, reverse roller and reverse registration roller if they are stained. 2. Is the original reading start sensor working? (Perform the input check: 03-[FAX]ON/[7]/[G]) * If it is working properly, proceed to 8. If not, check 3 to 7 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original reading start sensor or the harnesses are open circuited. Correct if any. 4. Perform the automatic adjustment of the original reading start sensor (05-356). 5. Perform the manual adjustment of the original reading start sensor. 6. Replace the original reading sensor, and then perform the automatic adjustment of the original reading start sensor (05-356). 7. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 8. Replace the original registration roller, intermediate transfer roller, reading start roller, reverse roller and reverse registration roller if they are worn out. |
| Error code: | E726 |
| Description: | Transport/exit signal reception jam during ADF standby status |
| Remedy: | 1. Check if there is any paper in the RADF. Remove it if there is. 2. Check if there is any paper in the equipment. Remove it if there is. 3. If a jam still occurs, turn the power OFF and then back ON to check if the equipment operates normally. |
| Error code: | E731 |
| Description: | Stop jam at the original exit sensor: The trailing edge of the original does not pass the original exit sensor after its leading edge has reached this sensor |
| Causes: | Original exit sensor RADF board Perform the 05-3210 Roller Exit roller |
| Remedy: | 1. Clean the exit roller and the exit intermediate roller if they are stained. 2. Is the original exit sensor working? (Perform the input check: 03-[FAX]ON/[7]/[E]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original exit sensor or the harnesses are open circuited. Correct if any. 4. Replace the original exit sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Replace the exit roller and the exit intermediate roller if they are worn out. |
| Error code: | E860 |
| Description: | Original jam access cover open: The Original jam access cover has opened during RADF operation. |
| Causes: | Original exit reverse sensor RADF board Perform the 05-3210 |
| Remedy: | 1. Close the original jam access cover or the original reverse unit if they are opened. Remove if there are any original before closing them. 2. Is the original jam access cover opening/closing sensor and the original revese unit opening/ closing sensor working? (Perform the input check: 03) Original jam access cover opening/closing sensor: 03-[FAX]ON/[7]/[C], Original revese unit opening/closing sensor: 03-[FAX]ON/[5]/[C] * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN74 or CN75 on the RADF board is disconnected from the original jam access cover opening/closing sensor, original revese unit opening/closing sensor or the harnesses are open circuited. Correct if any. 4. Replace the original jam access cover opening/closing sensor or the original revese unit opening/closing sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). |
| Error code: | E870 |
| Description: | RADF open jam: RADF has opened during RADF operation. |
| Causes: | RADF opening/closing sensor RADF board Perform the 05-3210 |
| Remedy: | 1. Close the RADF if it is opened. Remove if there is any original before closing it. 2. Is the RADF opening/closing sensor working? (Perform the input check: 03-[FAX]ON/[7]/[D]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN75 on the RADF board is disconnected from the RADF opening/ closing sensor or the harnesses are open circuited. Correct if any. 4. Replace the RADF opening/closing sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Is the RADF opening/closing sensor adjusted within the specified range? |
| Error code: | E871 |
| Description: | Cover open jam in the read ready status: Jam caused by opening of the Original jam access cover or front cover while the RADF is waiting for the scanning start signal from the equipment. |
| Causes: | Original jam access cover opening/ closing sensor RADF board Perform the 05-3210 |
| Remedy: | 1. Close the original jam access cover or the front cover if they are opened in the read ready status. 2. Is the original jam access cover sensor working? (Perform the input check: 03-[FAX]ON/[7]/[C]) 3. Check if the connector CN75 on the RADF board is disconnected from the Original jam access cover sensor or the harnesses are open circuited. Correct if any. 4. Replace the original jam access cover sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). |
| Error code: | E910 |
| Description: | Jam at the bridge unit transport sensor 1: The paper does not reach the bridge unit transport sensor 1 after it has passed the exit sensor. |
| Causes: | Bridge unit transport sensor-1 Bridge unit transport entrance motor Bridge unit transport exit motor LGC board DRV board PFC board Roller Transport roller of the bridge unit |
| Remedy: | 1. Check if there is any paper in the bridge unit and remove it if there is. 2. Is the bridge unit transport sensor-1 working? (Perform the input check:03-[FAX]OFF/[5]/[F]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN334 on the LGC board is disconnected from the bridge unit transport sensor-1 (entrance sensor) or the harnesses are open circuited. Check if the connector J510 of the bridge unit is disconnected. Correct if any. 4. Replace the bridge unit transport sensor-1. 5. Replace the LGC board. 6. Is the bridge unit gate solenoid working? (Perform the output check: 03-232) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connector CN334 on the LGC board is disconnected from the bridge unit gate solenoid or the harnesses are open circuited. Check if the connector J510 of the bridge unit is disconnected. Correct if any. 8. Replace the bridge unit gate solenoid. 9. Replace the LGC board. 10.Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: 03-113/163) * If it is working properly, proceed to 12. If not, check 11 below. 11.Check the drive system of the equipment and bridge unit. 12.Check if the rollers in the exit roller, the pressure spring and the bridge unit are worn out. |
| Error code: | E920 |
| Description: | Stop jam at the bridge unit transport sensor 1: The trailing edge of the paper does not pass the bridge unit transport sensor 1 after its leading edge has reached the sensor. |
| Causes: | Bridge unit transport sensor-1 Bridge unit transport entrance motor Bridge unit transport exit motor LGC board DRV board PFC board Roller Transport roller of the bridge unit |
| Remedy: | 1. Check if there is any paper in the bridge unit and remove it if there is. 2. Is the bridge unit transport sensor-1 working? (Perform the input check:03-[FAX]OFF/[5]/[F]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN334 on the LGC board is disconnected from the bridge unit transport sensor-1 (entrance sensor) or the harnesses are open circuited. Check if the connector J510 of the bridge unit is disconnected. Correct if any. 4. Replace the bridge unit transport sensor-1. 5. Replace the LGC board. 6. Is the bridge unit gate solenoid working? (Perform the output check: 03-232) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connector CN334 on the LGC board is disconnected from the bridge unit gate solenoid or the harnesses are open circuited. Check if the connector J510 of the bridge unit is disconnected. Correct if any. 8. Replace the bridge unit gate solenoid. 9. Replace the LGC board. 10.Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: 03-113/163) * If it is working properly, proceed to 12. If not, check 11 below. 11.Check the drive system of the equipment and bridge unit. 12.Check if the rollers in the exit roller, the pressure spring and the bridge unit are worn out. |
| Error code: | E930 |
| Description: | Jam at the bridge unit transport sensor 2: The trailing edge of the paper does not reach the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 1. |
| Causes: | Bridge unit transport sensor-2 LGC board Roller Transport roller of the bridge unit |
| Remedy: | 1. Check if there is any paper in the bridge unit and remove it if there is. 2. Is the bridge unit transport sensor-2 working? (Perform the input check:03-[FAX]OFF/[5]/[D]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN334 on the LGC board is disconnected from the bridge unit transport sensor-2 (exit sensor) or the harnesses are open circuited. Check if the connector J510 of the bridge unit is disconnected. Correct if any. 4. Replace the bridge unit transport sensor-2. 5. Replace the LGC board. 6. Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: 03-113/163) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check the drive system of the equipment and bridge unit. 8. Check if the rollers in the exit roller, the pressure spring and the bridge unit are worn out. 9. Replace the LGC board. 10.Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: 03-113/163) * If it is working properly, proceed to 12. If not, check 11 below. 11.Check the drive system of the equipment and bridge unit. 12.Check if the rollers in the exit roller, the pressure spring and the bridge unit are worn out. |
| Error code: | E940 |
| Description: | Stop jam at the bridge unit transport sensor 2: The trailing edge of the paper does not pass the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 2. |
| Causes: | Bridge unit transport sensor-2 LGC board Roller Transport roller of the bridge unit |
| Remedy: | 1. Check if there is any paper in the bridge unit and remove it if there is. 2. Is the bridge unit transport sensor-2 working? (Perform the input check:03-[FAX]OFF/[5]/[D]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN334 on the LGC board is disconnected from the bridge unit transport sensor-2 (exit sensor) or the harnesses are open circuited. Check if the connector J510 of the bridge unit is disconnected. Correct if any. 4. Replace the bridge unit transport sensor-2. 5. Replace the LGC board. 6. Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: 03-113/163) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check the drive system of the equipment and bridge unit. 8. Check if the rollers in the exit roller, the pressure spring and the bridge unit are worn out. 9. Replace the LGC board. 10.Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: 03-113/163) * If it is working properly, proceed to 12. If not, check 11 below. 11.Check the drive system of the equipment and bridge unit. 12.Check if the rollers in the exit roller, the pressure spring and the bridge unit are worn out. |
| Error code: | E9F0 |
| Description: | Hole punch jam: Hole punching is not performed properly. |
| Causes: | Punch HP sensor (S4) Punch motor (M3) Punch controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or equipment? → YES → Remove the paper. NO Is the connector J1 on the punch driver PC board disconnected? Is the harness connecting the punch driver PC board and punch home position sensor (PI3P) open circuited? → YES → Connect the connector securely. Replace the harness. NO Is the punch home position sensor working properly? l → NO → 1. Connect the connector of the punch home position sensor securely. 2. Replace the punch home position sensor. YES Replace the punch driver PC board. |
| Error code: | EA10 |
| Description: | Paper transport delay jam: Paper which has passed the exit sensor does not reach the inlet sensor. |
| Causes: | Feeding sensor (S22) Transport path switching solenoid (SOL5) Entrance motor (M1) Interface PC board (I/F) Finisher control PC board (FIN) |
| Remedy: | Is there any paper remaining on the transport path in the finisher or equipment? → YES → Remove the paper. NO Is the connector J17 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) open circuited? → YES → Connect the connector securely. Replace the harness. NO Is the inlet sensor working normally? (Check the movement of the actuator.) ll → NO → 1. Connect the connector of the inlet sensor securely. 2. Attach the actuator securely if its shaft is out of place. 3. Replace the inlet sensor. YES Replace the finisher controller PC board. |
| Error code: | EA20 |
| Description: | Paper transport stop jam: Paper which has reached the inlet sensor does not pass the inlet sensor. |
| Causes: | Entrance sensor (S1) Finisher control PC board (FIN) |
| Remedy: | Is there any paper remaining on the transport path in the finisher or main unit? → YES → Remove the paper. NO Is any of the connectors J17, J24, J9 and J11 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) opencircuited? Is the harness connecting the finisher controller PC board and buffer path inlet paper sensor (PI17) open-circuited? Is the harness connecting the finisher controller PC board and buffer path paper sensor (PI14) open circuited? Is the harness connecting the finisher controller PC board and stapling tray sensor (PI4) open circuited? Is the harness connecting the finisher controller PC board and delivery sensor (PI3) open circuited? → YES → Connect the connectors securely. Replace the harnesses. NO Is the inlet sensor working properly? (Check the movement of the actuator.) Is the buffer path inlet paper sensor working properly? (Check the movement of the actuator.) Is the buffer path paper sensor working properly? (Check the movement of the actuator.) Is the stapling tray sensor working properly? (Check the movement of the actuator.) Is the delivery sensor working properly? (Check the movement of the actuator.) ll → NO → 1. Connect the connectors of the sensors securely. 2. Attach the actuators securely if their shafts are out of place. 3. Replace the sensors. YES Replace the finisher controller PC board. |
| Error code: | EA21 |
| Description: | Paper size error jam: Paper does not reach the sensor because the paper is shorter than spec. [MJ-1103/1104] |
| Causes: | Entrance sensor (S1) Transport sensor (S2) Finisher controller board |
| Remedy: | MJ-1103/1104 1. Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. 2. Is the paper size used shorter than the size specified in the specifications? 3. Check if the connectors CN7 and CN22 on the finisher controller PC board are disconnected from the inlet sensor (S1) and the transport sensor (S2), or the harnesses are open circuited. Correct if any. 4. Replace the sensor. 5. Replace the finisher controller PC board. |
| Error code: | EA22 |
| Description: | Paper transport jam (Finisher paper punching edge detection sensor): [MJ-1103/1104] |
| Causes: | Paper position sensor (S6-1) Paper position sensor (S6-2) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path? YES Remove the paper, not leaving any chips. NO Is the paper too short for specifications? NO Use paper accepted in the specifications. YES Are the paper position sensor (S6-1 and S6-2) and its wiring correct? NO Replace the sensor. Correct the wiring. YES Replace the hole punch control PC board (HP). |
| Error code: | EA23 |
| Description: | Paper transport jam (exit sensor): [MJ-1103/1104] |
| Causes: | Transport sensor (S2) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or equipment? YES Remove the paper. NO Is there a disconnection of the connector, incorrect installation or breakage of the transport sensor (S2)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Replace the finisher control PC board (FIN). |
| Error code: | EA24 |
| Description: | Paper transport jam (between entrance and exit sensors): [MJ-1103/1104] |
| Causes: | Entrance sensor (S1) Transport sensor (S2) Entrance motor (M1) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or equipment? YES Remove the paper. NO Is the paper size used shorter than the size specified in the specifications? YES Use the paper size specified in the specifications. NO Is there a disconnection of the connector, incorrect installation or breakage of the entrance sensor (S1)? Is there a disconnection of the connector, incorrect installation or breakage of the transport sensor (S2)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the entrance motor (M1) and the CN26 of the finisher control PC board (FIN) disconnected or open circuited? Is the harness between the transport sensor (S2) and the CN6 of the finisher control PC board (FIN) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the finisher control PC board (FIN). |
| Error code: | EA25 |
| Description: | Paper transport jam (after paper stack exit): [MJ1103/1104] |
| Causes: | Finishing tray paper detection sensor (S12) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or equipment? YES Remove the paper. NO Is there any mechanical problem when the actuator of the finishing tray paper detection sensor (S12) is moved? YES Fix the mechanism. NO Is there a disconnection of the connector, incorrect installation or breakage of the finishing tray paper detection sensor (S12)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the finishing tray paper detection sensor (S12) and the CN18 of the finisher control PC board (FIN) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the finisher control PC board (FIN). |
| Error code: | EA26 |
| Description: | Paper transport jam (stop command request): [MJ1103/1104] |
| Causes: | Entrance sensor (S1) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the Finisher or the equipment? YES Remove the paper. NO Is there a disconnection of the connector, incorrect installation or breakage of the entrance sensor (S1)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the entrance sensor (S1) and the CN26 of the finisher control PC board (FIN) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the finisher control PC board (FIN). |
| Error code: | EA27 |
| Description: | Paper transport jam (paper not inserted): [MJ-1103/ 1104] |
| Causes: | Entrance sensor (S1) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the Finisher or the equipment? YES Remove the paper. NO Is there a disconnection of the connector, incorrect installation or breakage of the entrance sensor (S1)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the entrance sensor (S1) and the CN26 of the finisher control PC board (FIN) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the finisher control PC board (FIN). |
| Error code: | EA28 |
| Description: | Paper transport jam (assisting arm operation delay): [MJ-1103/1104] |
| Causes: | Assist arm motor (M10) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or equipment? YES Remove the paper. NO Is there any mechanical problem when the paper holding cam is rotated? YES Fix the mechanism. NO Is the harness between the assist arm motor (M10) and the CN13 of the finisher control PC board (FIN) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the finisher control PC board (FIN). |
| Error code: | EA29 |
| Description: | Paper transport jam (stack transport delay): [MJ1103/1104] |
| Causes: | Buffer tray guide motor (M2) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the Finisher or the equipment? YES Remove the paper. NO Is there any mechanical problem when the buffer tray guide is opened and closed while the buffer roller is kept raised? YES Fix the mechanism. NO Is the harness between the buffer tray guide motor (M2) and the CN11 of the finisher control PC board (FIN) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the finisher control PC board (FIN). |
| Error code: | EA30 |
| Description: | Power-ON jam: Paper is remaining at the inlet sensor when the power is turned ON. |
| Causes: | Entrance sensor Finisher controller PC board |
| Remedy: | Is there any paper remaining on the transport path in the finisher? → YES → Remove the paper. NO Is any of the connectors J17, J24 and J11 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) opencircuited? Is the harness connecting the finisher controller PC board and buffer path inlet paper sensor(PI17) open-circuited? Is the harness connecting the finisher controller PC board and buffer path paper sensor (PI14) open circuited? Is the harness connecting the finisher controller PC board and delivery sensor (PI3) open circuited? → YES → Connect the connectors securely. Replace the harnesses. NO Is the inlet sensor working properly? (Check the movement of the actuator.) Is the buffer path inlet paper sensor working properly? (Check the movement of the actuator.) Is the buffer path paper sensor working properly? (Check the movement of the actuator.) Is the delivery sensor working properly? (Check the movement of the actuator.) ll → NO → 1. Connect the connectors of the sensors securely. 2. Attach the actuators securely if their shafts are out of place. 3. Replace the sensors. YES Replace the finisher controller PC board. |
| Error code: | EA31 |
| Description: | Transport path paper remaining jam: The paper which has passed through the inlet sensor does not reach the transport sensor. [MJ-1103/1104] |
| Causes: | Transport sensor (S2) Finisher controller board |
| Remedy: | 1. Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. 2. Check if the connector CN22 on the finisher controller PC board is disconnected from the transport sensor (S2) or the harnesses are open circuited. Correct if any. 3. Check if the connectors CN7 and CN22 on the finisher controller PC board are disconnected from the inlet sensor (S1) and the transport sensor (S2), or the harnesses are open circuited. Correct if any. 4. Replace the sensor. 5. Replace the finisher controller PC board. |
| Error code: | EA32 |
| Description: | Exit paper remaining jam: The paper is remaining on the finishing tray when the power is turned ON. [MJ-1103/1104] |
| Causes: | Finishing tray paper detection sensor (S12) Finisher controller board |
| Remedy: | 1. Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. 2. Check and correct the mechanism. 3. Check if the connector CN11 on the finisher controller PC board is disconnected from the finishing tray paper detection sensor (S12) or the harnesses are open circuited. Correct if any. 4. Replace the sensor. 5. Replace the finisher controller PC board. |
| Error code: | EA40 |
| Description: | Door open jam: The upper cover or the front cover of the Finisher has opened, or the upper door or the front door of the Hole Punch Unit has opened during printing. |
| Causes: | Front cover switch (SW1) Stationary tray opening/closing switch (SW2) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or main unit? → YES → Remove the paper. NO Is the finisher connected with the main unit? → NO → Connect the finisher with the main unit. YES Is the connector J12 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and joint sensor (PI15) opencircuited? → YES → Connect the connector securely. Replace the harness. NO Is the joint sensor working properly? l → NO → 1. Connect the connector of the joint sensor securely. 2. Replace the joint sensor. YES Is the door of the finisher closed? → NO → Close the door. YES Is the connector J12 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and door opening sensor (PI16) open-circuited? → YES → Connect the connector securely. Replace the harness. NO Is the door opening sensor working properly? l → NO → 1. Connect the connector of the door opening sensor securely. 2. Replace the door opening sensor. YES Is the connector J5 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and door switch (MS1) opencircuited? → YES → Connect the connector securely. Replace the harness. NO Is the connector J5 on the punch driver PC board disconnected? Is the harness connecting the punch driver PC board and front door switch (MS2P) opencircuited? → YES → Connect the connector securely. Replace the harness. NO Are the upper and front door switches working properly? ll → NO → 1. Connect the connectors of the door switch and the front door switch securely. 2. Replace the upper/front door switches. YES Replace the finisher controller PC board. |
| Error code: | EA50 |
| Description: | Stapling jam: Stapling is not performed properly |
| Causes: | Stapler interference sensor (S11) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or equipment or on the stapling tray? → YES → Remove the paper. NO Is the jam cleared by taking off the staple cartridge from the finisher and removing the staple sheet slid from the staple case? → YES → End. NO Is the connector J8 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and stapling home position sensor (PI22) open circuited? → YES → Connect the connector securely. Replace the harness. NO Is the stapling home position sensor working properly? l → NO → 1. Connect the connector of the stapling home position sensor securely. 2. Replace the stapling home position sensor. YES Replace the finisher controller PC board. |
| Error code: | EA60 |
| Description: | Early arrival jam: The inlet sensor detects paper earlier than the specified timing |
| Causes: | Entrance sensor (S1) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or equipment? → YES → Remove the paper. NO Is the connector J17 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) open circuited? → YES → Connect the connector securely. Replace the harness. NO Is the inlet sensor working properly? (Check the movement of the actuator.) ll → NO → 1. Connect the connector of the inlet sensor securely. 2. Attach the actuator securely if its shaft is out of place. 3. Replace the inlet sensor. YES Replace the finisher controller PC board. |
| Error code: | EA70 |
| Description: | Stack exit belt home position error: The stack exit belt is not at the home position. [MJ-1103/1104] |
| Causes: | Stack belt exit home position sensor (S9) Stack transport motor (M5) Finisher controller board |
| Remedy: | 1. Check if the connector CN11 on the finisher controller PC board is disconnected from the stack belt exit home position sensor (S9) and the harnesses are open circuited. Correct if any. 2. Is the harness between the stack transport motor (M5) and the finisher control PC board (CN10) disconnected or open circuited? 3. Replace the sensor. 4. Replace the finisher controller PC board. 5. Is the upper surface detection sensor normal? (See CB31.) |
| Error code: | EA90 |
| Description: | Door open jam: The delivery cover or the inlet cover has opened during printing. |
| Causes: | Delivery cover sensor (PI3) Inlet cover sensor (PI9) Saddle stitcher controller board |
| Remedy: | main unit? → YES → Remove the paper. NO Is the saddle stitcher door closed? → NO → Close the door. YES Is either of the connectors J10 or J11 on saddle stitcher controller PC board disconnected? Are the harnesses connecting the saddle stitcher controller PC board and cover opening sensors (PI2S: front door opening/closing sensor, PI3S:delivery cover sensor, PI9S: inlet cover sensor) open-circuited? → YES → Connect the connector securely. Replace the harness. NO Are the cover opening sensors working properly? l → NO → 1. Connect the connectors of the cover opening sensors securely. 2. Replace the cover opening sensors. YES Replace the finisher controller PC board. |
| Error code: | EAA0 |
| Description: | Power-ON jam: Paper is remaining at the No. 1 paper sensor, No. 2 paper sensor, No. 3 paper sensor, vertical path paper sensor or delivery sensor when the power is turned ON. |
| Causes: | No. 1 paper sensor (PI18) No. 2 paper sensor (PI19) No. 3 paper sensor (PI20) Vertical path paper sensor (PI17) Delivery sensor (PI11) Saddle stitcher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or saddle stitcher section? → YES → Remove the paper. NO Is any of the connectors J10, J13 and J9 on the saddle stitcher controller PC board disconnected? Is the harness connecting the saddle stitcher controller PC board and No.1 paper sensor (PI18S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and No.2 paper sensor (PI19S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and No.3 paper sensor (PI20S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and vertical path paper sensor (PI17S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and delivery sensor (PI11S) open-circuited? → YES → Connect the connectors securely. Replace the harnesses. NO Is the No.1 paper sensor working properly? (Check the movement of the actuator.) Is the No.2 paper sensor working properly? (Check the movement of the actuator.) Is the No.3 paper sensor working properly? (Check the movement of the actuator.) Is the vertical path paper sensor working properly? (Check the movement of the actuator.) Is the delivery sensor working properly? (Check the movement of the actuator.) ll → NO → 1. Connect the connectors of the sensors securely. 2. Attach the actuators securely if their shafts are out of place. 3. Replace the sensors. YES Replace the saddle stitcher controller PC board. |
| Error code: | EAB0 |
| Description: | Paper transport stop jam: Paper which has passed the inlet sensor does not reach or pass the No. 1 paper sensor, No. 2 paper sensor, No. 3 paper sensor or delivery sensor. |
| Causes: | No. 1 paper sensor (PI18) No. 2 paper sensor (PI19) No. 3 paper sensor (PI20) Delivery sensor (PI11) Saddle stitcher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher, saddle stitcher section or main unit? → YES → Remove the paper. NO Is the connector J17 on finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) opencircuited? Is either of the connectors J10 or J9 on the saddle stitcher controller PC board disconnected? Is the harness connecting the saddle stitcher controller PC board and No.1 paper sensor (PI18S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and No.2 paper sensor (PI19S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and No.3 paper sensor (PI20S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and delivery sensor (PI11S) open-circuited? → YES → Connect the connectors securely. Replace the harnesses. NO Is the inlet sensor working properly? (Check the movement of the actuator.) Is the No.1 paper sensor working properly? (Check the movement of the actuator.) Is the No.2 paper sensor working properly? (Check the movement of the actuator.) Is the No.3 paper sensor working properly? (Check the movement of the actuator.) Is the delivery sensor working properly? (Check the movement of the actuator.) ll → NO → 1. Connect the connectors of the sensors securely. 2. Attach the actuators securely if their shafts are out of place. 3. Replace the sensors. YES Replace the saddle stitcher controller PC board. |
| Error code: | EAB1 |
| Description: | Short paper jam (Saddle Stitch Finisher) |
| Causes: | Feeding sensor (S22) Junction box paper detection sensor (S26) Transport path-2 (S27) Transport path-3 (S28) Ejecting roller (S29) Interface PC board (I/F) Saddle stitcher controller board Finisher controller board |
| Remedy: | Is there any paper remaining in the paper transport path in the equipment or the saddle stitch section of the Finisher? YES Remove the paper. NO Is the paper too short for specifications? YES Use paper accepted in the specifications. NO Is there a disconnection of the connector, incorrect installation or breakage of the feeding sensor (S22)? Is there a disconnection of the connector, incorrect installation or breakage of the junction box paper detection sensor (S24)? Is there a disconnection of the connector, incorrect installation or breakage of the transport path- 2 (S27)? Is there a disconnection of the connector, incorrect installation or breakage of the transport path- 3 (S28)? Is there a disconnection of the connector, incorrect installation or breakage of the ejecting roller (S29)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the feeding sensor (S22) or the junction box paper detection sensor (S24) and the CN8 of the interface PC board (I/F) disconnected or open circuited? Is the harness between the transport path-2 sensor (S27), transport path-3 sensor (S28) or ejecting roller sensor (S29) and the CN20 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO 1. Replace the saddle control PC board (SDL). 2. Replace the finisher control PC board (FIN). |
| Error code: | EAD0 |
| Description: | Print end command time-out jam: The printing has not finished normally due to the communication error between the SYS board and LGC board at the end of the printing. |
| Causes: | SYS board LGC board |
| Remedy: | Is the main motor rotating normally? → NO 1. Check if there is any paper in the equipment. Remove it if there is. 2. If the error still occurs, check the following: 3. Check if the error is cleared by turning the power OFF and then back ON. 4. Check if the connectors connecting the SYS board, SYSIF board, SLG board and PLG board are disconnected. 5. Check if the harnesses connecting the SYS board, SLG board and PLG board are open circuited. 6. Replace the SYS board, SYSIF board and LGC board. |
| Error code: | EAE0 |
| Description: | Receiving period time-out jam: The printing cannot be finished normally due to the communication error between the equipment and the Finisher when the paper is transported from the equipment to the Finisher. |
| Causes: | Finisher controller board |
| Remedy: | Is the finisher working? → YES → Replace the finisher controller PC board. NO 1. Check if the voltage (24V) is being supplied to the finisher. 2. Check the connection of the LGC board and IPC board. 3. Check if the harness connecting the IPC board and finisher I/F connector of the equipment side is open circuited. 4. Check if the harness connecting the I/F connector of the finisher side and finisher controller PC board is open circuited. 5. Replace the finisher controller PC board. |
| Error code: | EB30 |
| Description: | Ready period time-out jam: The equipment judges that the paper transport to the Finisher is disabled due to the communication error between the equipment and the Finisher at the start of the printing. |
| Causes: | Finisher controller board LGC board |
| Remedy: | Is there paper in the equipment? → NO → Replace the LGC board. YES Are the IPC board and LGC board properly connected to each other? → NO → Connect them properly. YES Is the harness securely connected to the IPC board? → NO → Connect the harness properly. YES Is any of the connector pins of the harness connecting the equipment and finisher disconnected or any of those harnesses open circuited? → NO → Connect the pin or replace the harness. YES 1. Replace the IPC board. 2. Replace the LGC board. 3. Replace the finisher controller PC board. |
| Error code: | EB50 |
| Description: | Paper remaining on the transport path: The multiple feeding of the preceding paper caused the misfeeding of the upcoming paper. |
| Causes: | 1st drawer feed sensor Bypass feed sensor ADU exit sensor Registration sensor 1st drawer feed sensor 2nd drawer feed sensor ADU board LGC board Rollers |
| Remedy: | In case the paper is fed from the 1st drawer, bypass unit or Open the bypass unit cover. Is there any paper in front of the drawer feed sensor? ll → YES → Remove the paper. * Clean or replace the feed roller and separation roller if this error occurs frequently. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Check the rollers. Clean or replace them. In case the paper is fed from the 2nd drawer, 3rd drawer, 4th drawer, Tandem LCF Open the bypass unit cover. Is there any paper in front of the 1st drawer transport sensor? ll → YES → Remove the paper. * Clean or replace the feed roller and separation roller if this error occurs frequently. NO Are the 1st drawer transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[C]) ↓ → NO → 1. Check if the connector of the 1st drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport sensor. 6. Replace the LGC board. YES If any paper remains in the equipment or drawer, remove it. Check the rollers. Clean or replace them. |
| Error code: | EB60 |
| Description: | Paper remaining on the transport path: The multiple feeding of the preceding paper caused the misfeeding of the upcoming paper (= redetection after no jam is detected at [EB50]). |
| Causes: | Registration sensor PFC board Rollers |
| Remedy: | Open the bypass unit cover. Is there any paper in front of the registration sensor? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Check the rollers. Clean or replace them. |
| Error code: | ED10 |
| Description: | Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position. [MJ-1103/1104 (when MJ-6102 is installed)] |
| Causes: | Skew adjustment motor (M1) Skew HP sensor (S2) Punch controller board |
| Remedy: | MJ-1103/1104 1. Check if there is any paper in the finisher or the on the transport path of the equipment. Remove it if there is. 2. Rotate skew adjustment motor and fix its mechanism if it does not rotate smoothly. 3. Check if the connectors on the hole punch controller PC board (HP board) are disconnected from the skew HP sensor (S2) and the skew adjustment motor, or the harnesses are open circuited. Correct if any. 4. Replace the skew adjustment motor. 5. Replace the hole punch control PC board. |
| Error code: | ED11 |
| Description: | Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position. [MJ-1103/1104 (when MJ6102 is installed)] |
| Causes: | Sideways adjustment motor (M2) Sideways deviation HP sensor (S3 Punch controller board |
| Remedy: | MJ-1103/1104 1. Check if there is any paper on the transport path and remove it if there is. 2. Rotate sideways adjustment motor and fix its mechanism if it does not rotate smoothly. 3. Check if the connectors on the hole punch controller PC board (HP board) are disconnected from the sideways deviation HP sensor (S3)and the sideways adjustment motor, or the harnesses are open circuited. Correct if any. 4. Replace the sideways adjustment motor. 5. Replace the hole punch control PC board. |
| Error code: | ED12 |
| Description: | Shutter home position error: The shutter is not at the home position. [MJ-1103/1104] |
| Causes: | Shutter opening/closing sensor (S4) Shutter clutch (CLT1) Finisher controller board |
| Remedy: | MJ-1103/1104 1. Open and close the shutter. If there is any mechanical problem, fix its mechanism. 2. Check if the connectors on the finisher controller PC board are disconnected from the shutter opening/closing sensor (S4) and the shutter clutch (CLT1), or the harnesses are open circuited. Correct if any. 3. Replace the shutter clutch (CLT1). 4. Replace the shutter opening/closing sensor (S4). 5. Replace the finisher controller PC board. |
| Error code: | ED13 |
| Description: | Front alignment plate home position error: The front alignment plate is not at the home position. [MJ1103/1104] |
| Causes: | Front alignment plate home position sensor (S7) Front alignment motor (M9) Finisher controller board |
| Remedy: | MJ-1103/1104 1. Move the front alignment plate. If there is any mechanical problem, fix its mechanism. 2. Check if the connectors on the finisher controller PC board are disconnected from the front alignment plate home position sensor (S7) and the front alignment motor (M9), or the harnesses are open circuited. Correct if any. 3. Replace the front alignment motor (M9). 4. Replace the front alignment plate home position sensor (S7). 5. Replace the finisher controller PC board. |
| Error code: | ED14 |
| Description: | Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ1103/1104] |
| Causes: | Rear alignment plate home position sensor (S7) Rear alignment motor (M10) Finisher controller board |
| Remedy: | MJ-1103/1104 1. Move the rear alignment plate. If there is any mechanical problem, fix its mechanism. 2. Check if the connectors on the finisher controller PC board are disconnected from the rear alignment plate home position sensor (S8) and the rear alignment motor (M10), or the harnesses are open circuited. Correct if any. 3. Replace the rear alignment motor (M10). 4. Replace the rear alignment plate home position sensor (S8). 5. Replace the finisher controller PC board. |
| Error code: | ED15 |
| Description: | Paddle home position error: The paddle is not at the home position. [MJ-1103/1104] |
| Causes: | Paddle home position sensor (S3) Paddle motor (M8) Finisher controller board |
| Remedy: | MJ-1103/1104 1. Rotate the paddle. If there is any mechanical problem, fix its mechanism. 2. Check if the connectors on the finisher controller PC board are disconnected from the paddle home position sensor (S3) and the paddle motor (M8), or the harnesses are open circuited. Correct if any. 3. Replace the paddle motor (M8). 4. Replace the paddle home position sensor (S3). 5. Replace the finisher controller PC board. |
| Error code: | ED16 |
| Description: | Buffer tray home position error: The buffer tray is not at the home position. [MJ-1103/1104] |
| Causes: | Buffer tray home position sensor (S5) Buffer tray guide motor (M3) Finisher controller board |
| Remedy: | MJ-1103/1104 1. Open and close the buffer tray guide. If there is any mechanical problem, fix its mechanism. 2. Check if the connectors on the finisher controller PC board are disconnected from the buffer tray home position sensor (S5) and the buffer tray guide motor (M3), or the harnesses are open circuited. Correct if any. 3. Replace the buffer tray guide motor (M3). 4. Replace the buffer tray home position sensor (S5). 5. Replace the finisher controller PC board. |
| Error code: | EF10 |
| Description: | Paper not supported for Saddle Stitch Finisher |
| Causes: | Buffer tray home position sensor (S5) Buffer tray guide motor (M3) Saddle controller board |
| Remedy: | Is there any paper remaining on the paper transport path in the Finisher or the equipment, or on the finishing tray? YES Remove the paper. NO Is the jam released by taking off the front staple cartridge from the Finisher and removing the staple sheet slid from the staple case? YES End. NO Is the harness between the front saddle stapler drive unit and the CN3 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely. • Replace the harness if open circuited. NO 1. Reconnect the connector securely if there is any disconnection. 2. Replace the saddle control PC board (SDL). |
| Error code: | EF11 |
| Description: | Saddle Stitch Finisher stapling error (front) |
| Causes: | Front saddle stapler drive unit Saddle controller board |
| Remedy: | Is there any paper remaining on the paper transport path in the Finisher or the equipment, or on the finishing tray? YES Remove the paper. NO Is the jam released by taking off the front staple cartridge from the Finisher and removing the staple sheet slid from the staple case? YES End. NO Is the harness between the front saddle stapler drive unit and the CN3 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely. • Replace the harness if open circuited. NO 1. Reconnect the connector securely if there is any disconnection. 2. Replace the saddle control PC board (SDL). |
| Error code: | EF12 |
| Description: | Saddle Stitch Finisher stapling error (rear) |
| Causes: | Rear saddle stapler drive unit Saddle controller board |
| Remedy: | Is there any paper remaining on the paper transport path in the Finisher or the equipment, or on the finishing tray? YES Remove the paper. NO Is the jam released by taking off the rear staple cartridge from the Finisher and removing the staple sheet slid from the staple case? YES End. NO Is the harness between the rear saddle stapler drive unit and the CN3 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO 1. Replace the rear saddle stapler drive unit. 2. Replace the saddle control PC board (SDL). |
| Error code: | EF13 |
| Description: | Saddle paper holder home position detection abnormality |
| Causes: | Paper holding home position sensor (S38) Saddle controller board |
| Remedy: | Is there any mechanical problem when the paper holding cam is rotated? YES Fix the mechanism. NO Is there a disconnection of the connector, incorrect installation or breakage of the paper holding home position sensor (S38)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the paper holding home position sensor (S38), paper holding clutch (CLT4) or saddle transport motor (M16) and the CN8 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the saddle control PC board (SDL). |
| Error code: | EF14 |
| Description: | Saddle paper exit jam |
| Causes: | Exit sensor (S31) Saddle controller board |
| Remedy: | Is there any paper remaining in the paper transport path of the equipment or the saddle stitch section of the Finisher? YES Remove the paper. NO Is there a disconnection of the connector, incorrect installation or breakage of the exit sensor (S31)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the exit sensor (S31) and the CN19 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the saddle control PC board (SDL). |
| Error code: | EF15 |
| Description: | Saddle Stitch Finisher side alignment motor home position detection abnormality |
| Causes: | Side alignment home position sensor (S36) Side alignment motor (M15) Saddle controller board |
| Remedy: | Is there any mechanical problem when the jog is moved? YES Fix the mechanism. NO Is there a disconnection of the connector, incorrect installation or breakage of the side alignment home position sensor (S36)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the side alignment home position sensor (S36) and the CN5 of the saddle control PC board (SDL) disconnected or open circuited? Is the harness between the side alignment motor (M15) and the CN5 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the saddle control PC board (SDL). |
| Error code: | EF16 |
| Description: | Saddle Stitch Finisher stacker motor home position detection abnormality |
| Causes: | Stacker home position sensor (S33) Stacker motor (M14) Saddle controller board |
| Remedy: | Is there any mechanical problem when the stacker carrier is moved? YES Fix the mechanism. NO Is there a disconnection of the connector, incorrect installation or breakage of the stacker home position sensor (S33)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the stacker home position sensor (S33) and the CN4 of the saddle control PC board (SDL) disconnected or open circuited? Is the harness between the stacker motor (M14) and the CN4 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the saddle control PC board (SDL). |
| Error code: | EF17 |
| Description: | Saddle Stitch Finisher folding blade home position detection abnormality |
| Causes: | Folding blade home position sensor (S35) Folding blade clutch (CLT3) Saddle controller board |
| Remedy: | Is there any mechanical problem when the folding blade cam is rotated? YES Fix the mechanism. NO Is there a disconnection of the connector, incorrect installation or breakage of the folding blade home position sensor (S35)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the folding blade home position sensor (S35) and the CN15 of the saddle control PC board (SDL) disconnected or open circuited? Is there a disconnection of the connector, incorrect installation or breakage of the folding blade clutch (CLT3)? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the saddle control PC board (SDL). |
| Error code: | EF18 |
| Description: | Saddle Stitch Finisher additional folding roller home position detection abnormality |
| Causes: | Additional folding home position sensor (S39) Additional folding motor (M20) Saddle controller board |
| Remedy: | Is there any mechanical problem when the additional folding carrier is moved? YES Fix the mechanism. NO Is there a disconnection of the connector, incorrect installation or breakage of the additional folding home position sensor (S39)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the additional folding home position sensor (S39) or the additional folding motor encoder sensor (S42) and the CN19 of the saddle control PC board (SDL) disconnected or open circuited? Is the harness between the additional folding motor (M20) and the CN18 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the saddle control PC board (SDL). |
| Error code: | EF19 |
| Description: | Saddle paper folding jam |
| Causes: | Exit transport sensor (S41) Saddle controller board |
| Remedy: | Is there any paper remaining in the paper transport path in the equipment or the saddle stitch section of the Finisher? YES Remove the paper. NO Is there a disconnection of the connector, incorrect installation or breakage of the exit transport sensor (S41)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the exit transport sensor (S41) and the CN19 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the saddle control PC board (SDL). |
| Error code: | EF20 |
| Description: | Saddle stacker jam |
| Causes: | Stacker paper detection sensor (S30) Saddle controller board |
| Remedy: | Is there any paper remaining in the paper transport path in the equipment or the saddle stitch section of the Finisher? YES Remove the paper. NO Is there a disconnection of the connector, incorrect installation or breakage of the stacker paper detection sensor (S30)? YES • Reconnect the connector securely if there is any disconnection. • Reinstall the sensor correctly if there is any incorrect installation. • Replace the sensor if there is any breakage. NO Is the harness between the stacker paper detection sensor (S30) and the CN14 of the saddle control PC board (SDL) disconnected or open circuited? l YES • Reconnect the connector securely if there is any disconnection. • Replace the harness if open circuited. NO Replace the saddle control PC board (SDL). |
| Error code: | F100_0 |
| Description: | HDD format error: Operation of HDD key data fails. |
| Remedy: | Setting Reboot the equipment. If it cannot be recovered, reinstall the software in the following procedure. (1) Install the OS data. |
| Error code: | F100_1 |
| Description: | HDD format error: Encryption key data of either the SYS board or the SRAM board for the SYS board are damaged. |
| Remedy: | Encryption key status Check the displayed message. ([3] + [C] + [POWER] → 5. Key Backup Restore) |
| Error code: | F100_2 |
| Description: | HDD format error: Encryption key data of both the SYS board and the SRAM board for the SYS board are damaged. |
| Remedy: | Encryption key status Check the displayed message. ([3] + [C] + [POWER] → 5. Key Backup Restore) |
| Error code: | F101_0 |
| Description: | HDD connection error (HDD connection cannot be detected.) |
| Causes: | HDD SYS board |
| Remedy: | HDD, SYS board, Setting 1. Turn the power of the equipment OFF and check the connection of the HDD. - Connector and harness check - Check if the connector pins of the HDD are bent. 2. If the error still occurs after step 1, perform the following. - Perform [3C] → [5] (Key Backup Restore) and check that each Key Status is "OK". - If not, recover the key (copy "SRAM Key Status" to "FROM Key Status" or vice versa). 3. If the error still persists after step 2, perform the following. - Perform [3C] → [3] (Format HDD), and then install "System Software (HD data)" with [49] - [4]. Notes: If F101_1 occurs with ADI-HDD and the error persists after performing step 3, perform step 3 after performing [4]+[C]+[POWER] → 1. Revert factory initial status HDD. 4. If the error persists even after step 3, replace the HDD. |
| Error code: | F101_1 |
| Description: | Root partition mount error (HDD formatting fails.): The HDD cannot be connected (mounted) caused by damage to the areas in which the program is mainly stored. |
| Causes: | HDD SYS board |
| Remedy: | HDD, SYS board, Setting 1. Turn the power of the equipment OFF and check the connection of the HDD. - Connector and harness check - Check if the connector pins of the HDD are bent. 2. If the error still occurs after step 1, perform the following. - Perform [3C] → [5] (Key Backup Restore) and check that each Key Status is "OK". - If not, recover the key (copy "SRAM Key Status" to "FROM Key Status" or vice versa). 3. If the error still persists after step 2, perform the following. - Perform [3C] → [3] (Format HDD), and then install "System Software (HD data)" with [49] - [4]. Notes: If F101_1 occurs with ADI-HDD and the error persists after performing step 3, perform step 3 after performing [4]+[C]+[POWER] → 1. Revert factory initial status HDD. 4. If the error persists even after step 3, replace the HDD. |
| Error code: | F101_2 |
| Description: | Normal partition mount error (HDD normal partition mounting fails.): The HDD cannot be connected (mounted) caused by damage to areas other than those described in the F101_0 and F101_1 errors. |
| Causes: | HDD SYS board |
| Remedy: | HDD, SYS board, Setting 1. Turn the power of the equipment OFF and check the connection of the HDD. - Connector and harness check - Check if the connector pins of the HDD are bent. 2. If the error still occurs after step 1, perform the following. - Perform [3C] → [5] (Key Backup Restore) and check that each Key Status is "OK". - If not, recover the key (copy "SRAM Key Status" to "FROM Key Status" or vice versa). 3. If the error persists after step 2, perform the following. - Check if the state of each partition is "OK" by performing [5]+[C]+[POWER] → 6. DISK Info. - If the state of partition is "NG", initialize the partition by performing [5]+[C]+[POWER] → 3. Initialize HDD. Notes: The following items will be deleted by performing step 3. . Message Log . Job Log . Spool Data (Print, Email reception) . Template 4. If the error still persists after step 3, perform the following. - Perform [3C] → [3] (Format HDD), and then install "System Software (HD data)" with [49] - [4]. 5. If the error persists even after step 4, replace the HDD. |
| Error code: | F101_3 |
| Description: | Encryption partition mount error (HDD encryption partition mounting fails.): The HDD cannot be connected (mounted) caused by damage to the areas in which the key is stored. |
| Causes: | HDD SYS board |
| Remedy: | HDD, SYS board, Setting 1. Turn the power of the equipment OFF and check the connection of the HDD. - Connector and harness check - Check if the connector pins of the HDD are bent. 2. If the error still occurs after step 1, perform the following. - Perform [3C] → [5] (Key Backup Restore) and check that each Key Status is "OK". - If not, recover the key (copy "SRAM Key Status" to "FROM Key Status" or vice versa). 3. If the error persists after step 2, perform the following. - Check if the state of each partition is "OK" by performing [5]+[C]+[POWER] → 6. DISK Info. - If the state of partition is "NG", initialize the partition by performing [5]+[C]+[POWER] → 3. Initialize HDD. Notes: The following items will be deleted by performing step 3. . Message Log . Job Log . Spool Data (Print, Email reception) . Template 4. If the error still persists after step 3, perform the following. - Perform [3C] → [3] (Format HDD), and then install "System Software (HD data)" with [49] - [4]. 5. If the error persists even after step 4, replace the HDD. |
| Error code: | F102 |
| Description: | HDD boot error: HDD does not become ready for booting. |
| Causes: | HDD SYS board |
| Remedy: | (1) Check if the connectors of the HDD are disconnected. (2) Check if the connector pins are disconnected or the wires of harnesses are broken. (3) Perform the bad sector check (08-694). If the check result is OK, recover the data in the HDD. If the check result is failed, replace the HDD. (4) Replace the SYS board. |
| Error code: | F103 |
| Description: | Finisher Paddle Failure An error was detected in the Finisher Paddle Motor. |
| Causes: | • Finisher Paddle Motor • Finisher Control Board |
| Remedy: | 1 Test these sensors. • Swing Guide Home Position Sensor • Paddle Home Position Sensor Run the appropriate Service Diagnostics sensor test. Do the sensors operate? Go to Step 2. Replace the sensor. If the error persists, go to Step 2. 2 Test the Paddle Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Paddle Motor test. Does the motor operate? Replace the Finisher Control Board. If the error persists, go to Step 4. Go to Step 4. 3 Check for +24 V to the Paddle Motor. Disconnect CN57. Is there +24 V across CN57-1 and -2 <=> ground? Replace the Delivery Motor. Replace the harness. If the error persists, go to Step 5. 4 Check all pins of the Inverter Interface Cable for continuity. Disconnect CN1 and CN2 from the Finisher Control Board and the opposite end from the Inverter. Is the cable conductive? Replace the Inverter Power Supply. Replace the cable. |
| Error code: | F104 |
| Description: | HDD data error: Abnormality is detected in the data of the HDD. |
| Causes: | HDD SYS board |
| Remedy: | (1) Check if the connectors of the HDD are disconnected. (2) Check if the connector pins are disconnected or the wires of harnesses are broken. (3) Perform the bad sector check (08-694). If the check result is OK, recover the data in the HDD. If the check result is failed, replace the HDD. (4) Replace the SYS board. |
| Error code: | F106_0 |
| Description: | ADI-HDD error: Illegal disk replacement detected (ADI-HDD Exchange to SATA-HDD) |
| Remedy: | Setting Check if the HDD has been replaced with a SATA-HDD (normal type). (1) Start the equipment in the 4C mode: [4] + [C] + [POWER] (2) Check the type of the HDD shown on the top left of the control panel display “Current HDD type”. 2a. In case of “SATA-HDD” (normal type), replace it with the original ADI-HDD or a new ADI-HDD. Notes: To replace with the original ADI-HDD, start the equipment in the normal mode and then reinstall master data (HD Data) only if any abnormality occurs. 2b. In case of “ADI-HDD” Check each item in the Measures field for the HDD below. If the error still occurs, reinstall the master data (HD Data). HDD • Connector check • Harness check • Perform the bad sector check (08-9072). If the check result is OK, recover the data in the HDD. If the check result fails, replace the HDD. |
| Error code: | F106_1 |
| Description: | ADI-HDD error: HDD type detection error |
| Remedy: | Setting If the error is not recovered after rebooting the equipment or no abnormality is found on any check items for the HDD, reinstall the master data (HD Data). HDD • Connector check • Harness check • Perform the bad sector check (08-9072). If the check result is OK, recover the data in the HDD. If the check result fails, replace the HDD. • Check that either the ADI-HDD or SATA-HDD (normal type) is mounted. (1) Start the equipment in the 4C mode: [4] + [C] + [POWER] (2) Check the type of the HDD shown on the top left of the control panel display “Current HDD type”. Normal status: ADI-HDD or SATA-HDD Abnormal status: Unknown HDD If “Unknown HDD” is displayed, reinstall the master data (HD Data). |
| Error code: | F106_2 |
| Description: | ADI-HDD error: ADI encryption key download operation error |
| Remedy: | Setting Checking of ADI-HDD encryption key status (1) Start the equipment in the 3C mode: [3] + [C] + [POWER] (2) The authentication menu is displayed. Press [OK]. (Not required in the default setting) (3) Select “5. Key Backup Restore” and then press the [START] button. (4) Check the status of the ADI-HDD encryption key on the Key Backup Restore Mode menu. (5) After the operation is completed, shut down the equipment by pressing the [POWER] button. • In case both the SRAM ADIKey and FROM ADIKey status are OK • Reinstall the system ROM data (OS Data). • In case either the SRAM ADIKey or FROM ADIKey status is other than OK Restore the ADI-HDD encryption key. • In case both of the SRAM ADIKey and FROM ADIKey status are other than OK Reinstall the master data (HD Data). |
| Error code: | F106_3 |
| Description: | ADI-HDD error: ADI authentication Admin Password generation error |
| Remedy: | Reinstall the system ROM data (OS Data). Reinstall the master data (HD Data). |
| Error code: | F106_4 |
| Description: | ADI-HDD error: Authentication random number generation error |
| Remedy: | Reinstall the system ROM data (OS Data). Reinstall the master data (HD Data). |
| Error code: | F106_5 |
| Description: | ADI-HDD error: Authentication data transmission error |
| Remedy: | Reinstall the system ROM data (OS Data). Reinstall the master data (HD Data). • In case this error occurred after returning SRAM data for SRAM cloning: Copy the ADI-HDD encryption key from FROM to SRAM. (1) Start the equipment in the 3C mode: [3] + [C] + [POWER] (2) The authentication menu is displayed. Press [OK]. (Not required in the default setting) (3) Select “5. Key Backup Restore” and then press the [START] button. (4) Select “6. ADIKey FROM to SRAM” and then press the [START] button. (5) After the restoring of the encryption key has completed, “Operation Complete” is displayed. (6) After the operation has completed, shut down the equipment by pressing the [POWER] button. |
| Error code: | F109_0 |
| Description: | Key consistency error: Consistency check operation error. |
| Causes: | SRAM board SYS board |
| Remedy: | Setting Reboot the equipment. If it cannot be recovered, reinstall the software in the following procedure. (1) Install the OS data. (2) Reinstall the master data and application program. SRAM board (for SYS board) If the error is not cleared after the software reinstallation, replace the SRAM board. "9.2.6 Precautions and Procedures when replacing SRAM board (for SYS board)" SYS board If the error is not cleared after this (see above), replace the SYS board. "9.2.4 Precautions and Procedures when replacing the SYS board" |
| Error code: | F109_1 |
| Description: | Key consistency error: SRAM encryption AES key data damage. |
| Remedy: | Reboot the equipment. If it cannot be recovered, reinstall the software in the following procedure. (1) Install the OS data. (2) Reinstall the master data and application program. |
| Error code: | F109_2 |
| Description: | Key consistency error: Signature Check public key damage. |
| Remedy: | Reboot the equipment. If it cannot be recovered, reinstall the software in the following procedure. (1) Install the OS data. (2) Reinstall the master data and application program. |
| Error code: | F109_3 |
| Description: | Key consistency error: HDD encryption parameter damage. |
| Remedy: | Encryption key status confirmation Check the message displayed by [3] + [C] + [POWER] → 5. Key Backup Restore. |
| Error code: | F109_4 |
| Description: | Key consistency error: license data damage. |
| Remedy: | Encryption key status confirmation Check the message displayed by [3] + [C] + [POWER] → 5. Key Backup Restore |
| Error code: | F109_5 |
| Description: | Key consistency error (encryption key for ADI-HDD is damaged) |
| Remedy: | Encryption key status confirmation Check the message displayed by [3] + [C] + [POWER] → 5. Key Backup Restore. |
| Error code: | F109_6 |
| Description: | Key consistency error (administrator password error for ADI-HDD authentication) |
| Remedy: | Encryption key status confirmation Check the message displayed by [3] + [C] + [POWER] → 5. Key Backup Restore. |
| Error code: | F110 |
| Description: | Finisher Staple Motor Failure An error was detected in the Staple Motor. |
| Causes: | • Finisher Staple Motor • Finisher Control Board |
| Remedy: | 1 Test these sensors. • Staple Clock Sensor • Fold Home Position Sensor Run the appropriate Service Diagnostics sensor test. Do the sensors operate? Go to Step 2. Replace the sensor. If the error persists, go to Step 2. 2 Test the Staple Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Staple Motor tests. Does the motor operate? Replace the Finisher Control Board. If the error persists, go to Step 4. Go to Step 3. 3 Check for +24 V to the Staple Motor. Disconnect CN71. Is there +24 V across CN71-1 and -2 <=> ground? Replace the Staple Motor. Replace the harness. If the error persists, go to Step 4. 4 Check all pins of the Inverter Interface Cable for continuity. Disconnect CN1 and CN2 from the Finisher Control Board and the opposite end from the Inverter. Is the cable conductive? Replace the Inverter Power Supply. Replace the cable. |
| Error code: | F111 |
| Description: | Finisher Stack Handling Motor Failure The Delivery Belt Home Position Sensor detected a Stack Handling error. |
| Causes: | • Finisher Stack Handling Motor • Finisher Control Board |
| Remedy: | 1 Check the delivery mechanism. Does the Delivery Belt turn freely when operated manually? Go to Step 2. Repair the mechanism. 2 Test the Delivery Belt Home Position Sensor. Run the Service Diagnostics Exit Belt Home Position Sensor test. Does the sensor operate? Go to Step 3. Replace the sensor. If the error persists, go to Step 3. 3 Test the Staple Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Staple Motor tests. Does the motor operate? Replace the Finisher Control Board. If the error persists, go to Step 4. Go to Step 4. 4 Check for +24 V to the Staple Motor. Disconnect CN59. Is there +24 V across CN59-1 and -2 <=> ground? Replace the Stack Handling Motor. Replace the harness. If the error persists, go to Step 5. 5 Check all pins of the Inverter Interface Cable for continuity. Disconnect CN1 and CN2 from the Finisher Control Board and the opposite end from the Inverter. Is the cable conductive? Replace the Inverter Power Supply. Replace the cable. |
| Error code: | F120 |
| Description: | Database abnormality: Databases do not run normally. |
| Remedy: | (1) Rebuild the databases. (Perform 08-684.) (2) If the error is not recovered, initialize the HDD. (Key in “2” at 08-690.) |
| Error code: | F121 |
| Description: | Database abnormality (user management database) |
| Remedy: | Setting 1. Delete the log in the following procedure:[5] + [C] + [POWER] → 4. Initialize database → 1. LDAP database (to delete user database) (Note that all user, role, group and accounting data will be deleted.) 2. If the error is not recovered, reinstall the system software. ([4] + [9] + [POWER] → 4. System Software(HD data)) Notes: • If you rebuild the databases with a job remaining, delete it after finishing. • When “Rebuilding all databases” is performed, all data including log/user/role/group/department information and address book data are deleted. If you back up the data in advance, they will be recovered by restoring them after rebuilding the database. |
| Error code: | F122 |
| Description: | Database 3 abnormality (log management database) |
| Remedy: | Setting 1. Delete the log in the following procedure: [5] + [C] + [POWER] → 4. Initialize database → 2. Log database (jobs and messages) (Note that all job and message logs will be deleted.) 2. If the error is not recovered, reinstall the system software. ([4] + [9] + [POWER] → 4. System Software(HD data)) Notes: • If you rebuild the databases with a job remaining, delete it after finishing. • When “Rebuilding all databases” is performed, all data including log/user/role/group/department information and address book data are deleted. If you back up the data in advance, they will be recovered by restoring them after rebuilding the database. |
| Error code: | F124 |
| Description: | Database abnormality: Database is not operating normally. (Language management database) |
| Remedy: | Setting Delete the journal file: [5] + [C] + [START] → 4. Initialize DB - > 3. Language DB If the recovery is still not completed, reinstall the master data and application program. "11.2.1 Master data/ System ROM" |
| Error code: | F130 |
| Description: | Controller to Engine Communications Failure An communications error was detected. |
| Causes: | • Engine Control Board, PL1.1.4 |
| Remedy: | 1 Cycle power to the printer. Does the error persist? Go to Step 2. Complete 2 Reseat the CUIF connector. Does the error persist? Replace the Engine Control Board. If the error persists, replace the Image Processor Board Complete |
| Error code: | F131 |
| Description: | Finisher Fold Position Sensor Failure An error was detected with the Fold Position Sensor. |
| Causes: | • Fold Position Sensor • Finisher Control Board |
| Remedy: | 1 Test the Folding Position Sensor. Run the Service Diagnostics Bookbinding Position Sensor test. Does the sensor function correctly? Replace the Finisher Control Board. Go to Step 2. 2 Check the sensor connection. Is CN39 connected? Go to Step 3. Reconnect the sensor. 3 Replace the sensor. Does the error persist? Go to Step 4. Complete 4 Check all pins on the harness for continuity. Is the harness conductive? Replace the Finisher Control Board. Replace the harness. |
| Error code: | F140 |
| Description: | ASIC format error: ASIC formatting fails or memory acquiring fails when software is formatted |
| Causes: | SYS board Main memory |
| Remedy: | SYS board • Connector check • Board check Main memory • Check the installation • Main memory check |
| Error code: | F200 |
| Description: | Data overwrite option (GP-1070) disabled |
| Causes: | SYS board |
| Remedy: | Perform firmware installation (some firmware: OS, HDD, SYS, Laser Firmware, PFC Firmware, Engine Main Firmware, and Scanner Firmware) with the USB media. "6.1 Firmware Updating with USB Media" * When the function of the Data Overwrite Enabler (GP-1070) is deleted from the equipment, the service call “F200” occurs. |
| Error code: | F400 |
| Description: | SYS board cooling fan abnormality |
| Causes: | SYS board cooling fan SYS board |
| Remedy: | (1) Check if the fan is rotating properly. (2) If not, check if any foreign object is adhered. (3) Are the connector CN112 and the relay connector of the SYS board connected securely? (4) Replace the SYS board cooling fan. |
| Error code: | F500 |
| Description: | HD partition damage |
| Remedy: | Setting • Diagnose the file system with [5] + [C] + [POWER] → 1. Check F/S, and then recover the problem partition with [5] + [C] + [POWER] → 2. Recovery F/S. • If it still is not recovered by performing the above, reinstall the software after formatting the HDD with [3] + [C] + [POWER] → 3: Format HDD. |
| Error code: | F510 |
| Description: | Software boot-up error |
| Remedy: | Setting 1. Reboot. 2. If it has still not recovered, reinstall the HDD software. 3. If it still persists after step 2, perform [3] + [C] + [POWER] → 3, and then reinstall the HDD software. Notes: User data will be deleted when [3] + [C] + [POWER] → 3 is performed. |
| Error code: | F520 |
| Description: | Software boot-up error |
| Remedy: | Setting 1. Reboot. 2. If it has still not recovered, reinstall the HDD software. 3. If it still persists after step 2, perform [3] + [C] + [POWER] → 3, and then reinstall the HDD software. Notes: User data will be deleted when [3] + [C] + [POWER] → 3 is performed. |
| Error code: | F521 |
| Description: | Integrity check error |
| Remedy: | Setting Restart the equipment. If the error is not recovered after restarting the equipment, reinstall software following the procedure below. (1) Turn the power OFF. (2) Turn the power back ON while pressing the [4] and [9] buttons simultaneously. (3) The authentication screen is displayed. Enter the password. (Password entry is not required under the default setting.) (4) Key in [1] to select “1. SYSTEM FIRMWARE (OS data)” and [4] to select “4. SYSTEM SOFTWARE (OS data) “, and then press the [START] button. (5) When updating is completed properly, “Update successful completed Restart the MFP” is displayed on the touch panel. |
| Error code: | F550 |
| Description: | Encryption partition error |
| Remedy: | Setting • Recover the encryption key with [3] + [C] + [POWER] → 5. |
| Error code: | F600 |
| Description: | Software update error |
| Remedy: | Setting 1. Perform [3] + [C] + [POWER] → [1] → [START] for “Clear Error Flag in Software Installation”. 2. Reinstall the firmware in error displayed on the F600 error screen. |
| Error code: | F700 |
| Description: | Overwrite error |
| Remedy: | Setting • If a service call occurs again after the reboot, replace the HDD. |
| Error code: | F800 |
| Description: | Date error |
| Remedy: | Setting Reset the date, and request the administrator to set the date and time. 1. Turn the power on while pressing the [6] and [CLEAR] button. 2. Select [2] key, and then press the [START] button. 3. Press the [START] button on the confirmation screen displayed. (The date is set to January 1st, 2011.) 4. Request the administrator to set the date and time. |
| Error code: | F900 |
| Description: | Model information error |
| Remedy: | Setting Recover the machine information by means of the following procedure. Notes: The following procedure is supported in the firmware with the version “2050” or later. If the version is before “2050”, first upgrade it to “2050” or later with [4] + [9] → [1] for “SYSTEM FIRMWARE (OS Data)”. <Machine information recovery> 1. Turn the power ON while pressing [6] and the [CLEAR] button simultaneously. 2. Key in [3] to select “3. SRAM Re-Initialize Support”, and then press the [START] button. 3. After the operation is completed, shut down the equipment by pressing the [ON/OFF] button. * If it is not recovered, perform the following procedure. 4. Turn the power ON while pressing [3] and the [CLEAR] button simultaneously. 5. Enter the password on the Authentication screen. If no password is set for Service, press the [OK] button without entering anything. If the High Security Mode has been set, enter “#1048#”. 6. Key in [5] to select “5. Key Backup Restore”, and then press the [START] button. 7. Key in [2] to select “2. Key FROM to SRAM”, and then press the [START] button. 8. After the operation is completed, shut down the equipment by pressing the [ON/OFF] button. |
