Toshiba e-Studio 360CP
Рейтинг
Модули
High-capacity feeder 2
High-capacity feeder 4
Expansion feeder 1
Covers 3
Electrical A2
RIP board
Base 3
High-capacity feeder 6
DUPLEX UNIT 2
Electrical A
PAPER FEED
Finisher feed 2
Finisher elevator
Covers 1
High-capacity feeder 5
Base 2
High-capacity feeder 3
Finisher covers
CASSETTE
Expansion feeder 2
Covers 4
DUPLEX UNIT 1
Finisher frame
Covers 2
Covers 5
FUSER UNIT
Finisher electronics
Electrical B
High-capacity feeder 1
Finisher docking 1
Finisher docking 2
Upper unit
Finisher feed 1
Детали Finisher covers
| Деталь: | Solenoid assembly, paper pickup |
| Парткод: | 56P9846 |
| Деталь: | Clutch, paper feed |
| Парткод: | 56P9848 |
| Деталь: | Motor assembly, transport |
| Парткод: | 56P9844 |
| Деталь: | ARM, PICK-UP |
| Парткод: | 56P9944 |
| Деталь: | SPRING, PRESSURE |
| Парткод: | 56P9504 |
| Деталь: | Interrupter, photo |
| Парткод: | 56P9528 |
| Деталь: | Roller, manual feed pickup |
| Парткод: | 56P9849 |
| Деталь: | Roller, manual feed |
| Парткод: | 56P9850 |
| Деталь: | LIMITER, TORQUE |
| Парткод: | 56P9852 |
| Деталь: | Roller, manual feed separate |
| Парткод: | 56P9854 |
| Деталь: | Sensor assembly, paper feed |
| Парткод: | 56P9845 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | 56P9847 |
| Деталь: | Parts packet |
| Парткод: | 56P9959 |
| Деталь: | Sensor, resistor |
| Парткод: | 56P9541 |
| Деталь: | Cable assembly, safety switch |
| Парткод: | 56P9875 |
| Деталь: | Cable assembly, HCF motor |
| Парткод: | 56P9865 |
| Деталь: | Cable assembly, I/F |
| Парткод: | 56P9871 |
| Деталь: | Cable assembly, paper feed sensor |
| Парткод: | 56P9866 |
| Деталь: | Cable, up/down switch |
| Парткод: | 56P9880 |
| Деталь: | Cable, paper volume |
| Парткод: | 56P9879 |
| Деталь: | Cable assembly, sensor |
| Парткод: | 56P9878 |
| Деталь: | Cable assembly, paper size sensor |
| Парткод: | 56P9877 |
| Деталь: | Cable assembly, lift motor |
| Парткод: | 56P9876 |
| Деталь: | Board, high-capacity feed |
| Парткод: | 56P2658 |
| Деталь: | Cable assembly, power supply out |
| Парткод: | 56P9873 |
| Деталь: | Cable assembly, power supply in |
| Парткод: | 56P9872 |
| Деталь: | Cable assembly, power supply |
| Парткод: | 56P9874 |
| Деталь: | Converter, DC/DC |
| Парткод: | 56P9870 |
| Деталь: | Power supply, HCF |
| Парткод: | 56P4008 |
| Деталь: | Cable assembly, drawer ground |
| Парткод: | 56P9867 |
| Деталь: | Roller, track |
| Парткод: | 56P9861 |
| Деталь: | SWITCH, MICRO |
| Парткод: | 56P9864 |
| Деталь: | SWITCH, PUSH |
| Парткод: | 56P9530 |
| Деталь: | Spring, pressure pickup |
| Парткод: | 56P9501 |
| Деталь: | Switch, HCF push |
| Парткод: | 56P9863 |
| Деталь: | Parts packet |
| Парткод: | 56P9961 |
| Деталь: | Motor asm, stepping |
| Парткод: | 40X1090 |
| Деталь: | Cable asm, upper optional drawer |
| Парткод: | 56P9777 |
| Деталь: | Cable asm, lower optional drawer |
| Парткод: | 56P9778 |
| Деталь: | Cover, right side C |
| Парткод: | 40X1204 |
| Деталь: | Cover, right side B |
| Парткод: | 40X1203 |
| Деталь: | Cover, right side A |
| Парткод: | 40X1202 |
| Деталь: | Cable asm, expansion paper level |
| Парткод: | 40X1091 |
| Деталь: | Interrupt, photo |
| Парткод: | 40X1173 |
| Деталь: | FOOT, RUBBER |
| Парткод: | 56P9503 |
| Деталь: | Cover, front feed |
| Парткод: | 40X1200 |
| Деталь: | Screw, slide rail |
| Парткод: | 56P9524 |
| Деталь: | Rail, base left side |
| Парткод: | 40X1034 |
| Деталь: | Cover. left side |
| Парткод: | 40X1201 |
| Деталь: | GUIDE, WIRE |
| Парткод: | 11G0199 |
| Деталь: | Lever, size sense |
| Парткод: | 56P9521 |
| Деталь: | Card, size sense |
| Парткод: | 56P9522 |
| Деталь: | Cable asm, size sense |
| Парткод: | 56P9775 |
| Деталь: | Board, expansion feeder controller |
| Парткод: | 56P2657 |
| Деталь: | Gear, Z30 |
| Парткод: | 40X1096 |
| Деталь: | Gear, IDS 38 |
| Парткод: | 40X1093 |
| Деталь: | Motor, paper tray lift |
| Парткод: | 40X1097 |
| Деталь: | Cable asm, expansion lift motor |
| Парткод: | 40X1092 |
| Деталь: | Belt, timing S3M:177 |
| Парткод: | 40X1095 |
| Деталь: | Gear, Z28:20T |
| Парткод: | 40X1246 |
| Деталь: | COVER, REAR |
| Парткод: | 40X1167 |
| Деталь: | Assembly, expansion feeder |
| Парткод: | 56P4024 |
| Деталь: | Plate, Ground |
| Парткод: | 11G0399 |
| Деталь: | Pulley, timing 20t |
| Парткод: | 40X1094 |
| Деталь: | Parts packet |
| Парткод: | 40X1269 |
| Деталь: | Cord (6ft straight), Israel |
| Парткод: | 40X0275 |
| Деталь: | Cord (6ft straight), South Africa |
| Парткод: | 40X0276 |
| Деталь: | Cord (6ft high amp straight), Brazil (HV, LV) |
| Парткод: | 40X0277 |
| Деталь: | Cord (HV 6ft straight), Austria, Russia |
| Парткод: | 40X0278 |
| Деталь: | Cord (6ft straight), Denmark, Finland, Norway, Sweden |
| Парткод: | 40X0279 |
| Деталь: | Cord (10A 3 cond. 6ft straight) , Korea |
| Парткод: | 40X0280 |
| Деталь: | Cord (13A 3 cond. 6ft straight), Taiwan |
| Парткод: | 40X0281 |
| Деталь: | Cord (1.77M straight), Peoples Republic of China |
| Парткод: | 40X0282 |
| Деталь: | Cord (6ft straight), Australia |
| Парткод: | 40X0296 |
| Деталь: | Interuptor, photo (paper low sensor) |
| Парткод: | 40X1104 |
| Деталь: | Parts packet |
| Парткод: | 40X1267 |
| Деталь: | Transformer (Japan Only) |
| Парткод: | 56P9964 |
| Деталь: | Card assembly, RIP |
| Парткод: | 40X4248 |
| Деталь: | Fan, RIP box |
| Парткод: | 40X4520 |
| Деталь: | Cable assembly, power RIP |
| Парткод: | 56P9749 |
| Деталь: | Box, RIP |
| Парткод: | 40X1165 |
| Деталь: | Cable assembly, 26 pin RIP printer controller |
| Парткод: | 40X4054 |
| Деталь: | CABLE, USB |
| Парткод: | 40X4255 |
| Деталь: | Cable, operator panel |
| Парткод: | 40X4256 |
| Деталь: | Cover, RIP box |
| Парткод: | 40X1166 |
| Деталь: | Parts packet |
| Парткод: | 40X4268 |
| Деталь: | Parts packet |
| Парткод: | 40X1265 |
| Деталь: | Pin, upper unit support |
| Парткод: | 56P9667 |
| Деталь: | HANDLE, LOCK |
| Парткод: | 56P9669 |
| Деталь: | Shroud, cable |
| Парткод: | 56P9670 |
| Деталь: | GUIDE, CABLE |
| Парткод: | 56P9671 |
| Деталь: | Support assembly, upper unit |
| Парткод: | 40X1207 |
| Деталь: | Handle assembly, lock |
| Парткод: | 40X1208 |
| Деталь: | Cover, electronic |
| Парткод: | 40X1151 |
| Деталь: | GUIDE, CABLE |
| Парткод: | 56P9672 |
| Деталь: | Plate, upper side fence |
| Парткод: | 56P9892 |
| Деталь: | Knob, stopper |
| Парткод: | 56P9893 |
| Деталь: | Knob, tray |
| Парткод: | 56P9891 |
| Деталь: | Plate, paper adhesion |
| Парткод: | 56P9890 |
| Деталь: | Fence assembly, front side |
| Парткод: | 56P9915 |
| Деталь: | Fence assembly, rear side |
| Парткод: | 56P9894 |
| Деталь: | Interrupter, photo |
| Парткод: | 56P9528 |
| Деталь: | Pad, friction |
| Парткод: | 56P9889 |
| Деталь: | Parts packet |
| Парткод: | 56P9963 |
| Деталь: | Plate, paper re-feed drawer |
| Парткод: | 56P9825 |
| Деталь: | Guide, rear side |
| Парткод: | 56P9827 |
| Деталь: | Guide, front side |
| Парткод: | 56P9826 |
| Деталь: | Solenoid assembly, paper re-feed |
| Парткод: | 56P3992 |
| Деталь: | Bearing, release |
| Парткод: | 56P9814 |
| Деталь: | Spring, re-feed roller |
| Парткод: | 56P9816 |
| Деталь: | Roll, release |
| Парткод: | 56P9813 |
| Деталь: | Interrupter, photo |
| Парткод: | 40X1171 |
| Деталь: | Motor assembly, paper guide |
| Парткод: | 56P9828 |
| Деталь: | Interrupter, photo |
| Парткод: | 40X1173 |
| Деталь: | Spring, feed roller |
| Парткод: | 56P9526 |
| Деталь: | Spring, reed roller |
| Парткод: | 56P9815 |
| Деталь: | Solenoid assembly, feed roller |
| Парткод: | 56P3991 |
| Деталь: | Cable assembly, duplex drawer |
| Парткод: | 56P3993 |
| Деталь: | Roller, follow-up feed |
| Парткод: | 40X1175 |
| Деталь: | GEAR, IDLER |
| Парткод: | 56P9527 |
| Деталь: | Gear, carrying roller |
| Парткод: | 56P9817 |
| Деталь: | Pulley, carrying roller timing |
| Парткод: | 56P9818 |
| Деталь: | Pulley, feed roller |
| Парткод: | 56P9819 |
| Деталь: | BELT, TIMING |
| Парткод: | 56P9822 |
| Деталь: | BELT, TIMING |
| Парткод: | 56P9823 |
| Деталь: | Knob, paper re-feed |
| Парткод: | 56P9821 |
| Деталь: | Pulley, re-feed roller |
| Парткод: | 56P9820 |
| Деталь: | Roller, drive feed |
| Парткод: | 40X1174 |
| Деталь: | Plate, paper carrying drawer |
| Парткод: | 56P9824 |
| Деталь: | Roller, middle feed |
| Парткод: | 40X1176 |
| Деталь: | Roller, re-feed |
| Парткод: | 40X1177 |
| Деталь: | Parts packet |
| Парткод: | 40X1271 |
| Деталь: | Cord (8ft right angle) , US, Canada, ET AL |
| Парткод: | 40X0269 |
| Деталь: | Cord (8ft 15A straight), Japan |
| Парткод: | 40X0270 |
| Деталь: | Cord (6ft straight), England, France, Germany, Spain, Belgium |
| Парткод: | 40X0286 |
| Деталь: | Cord (8ft right angle), Argentina, Paraguay, Uruguay |
| Парткод: | 40X0272 |
| Деталь: | Cord (8ft straight), Italy |
| Парткод: | 40X0273 |
| Деталь: | Cord (6ft straight), Switzerland |
| Парткод: | 40X0274 |
| Деталь: | Cord (8ft straight ), UK |
| Парткод: | 40X0271 |
| Деталь: | Cable asm, finisher |
| Парткод: | 40X1102 |
| Деталь: | Cable asm, printer controller power 2 |
| Парткод: | 56P9727 |
| Деталь: | Supply, high voltage |
| Парткод: | 56P3983 |
| Деталь: | Cable asm, feeder |
| Парткод: | 40X1042 |
| Деталь: | SENSOR, HUMIDITY |
| Парткод: | 40X1247 |
| Деталь: | Asm, HCF/FIN D-Sub |
| Парткод: | 40X1101 |
| Деталь: | Cable asm, HVU |
| Парткод: | 56P9715 |
| Деталь: | Cable asm, printer controller power 1 |
| Парткод: | 40X1053 |
| Деталь: | Card, CK1 Daughter |
| Парткод: | 40X1084 |
| Деталь: | Card, conditioning (230V only) |
| Парткод: | 56P3988 |
| Деталь: | Cable, motor driver power |
| Парткод: | 56P9747 |
| Деталь: | Cable asm, duplex connector |
| Парткод: | 56P2670 |
| Деталь: | Supply, 120V power 1 |
| Парткод: | 56P3984 |
| Деталь: | Supply, 230V power 1 |
| Парткод: | 56P3985 |
| Деталь: | SHEET, INSULATION |
| Парткод: | 56P9737 |
| Деталь: | Fuse, thermal (230V only) |
| Парткод: | 56P9943 |
| Деталь: | Cable, conditioning joint (230V only) |
| Парткод: | 56P9738 |
| Деталь: | Resistor, conditioning (230V only) |
| Парткод: | 56P9741 |
| Деталь: | Cable, conditioning resistor (230V only) |
| Парткод: | 56P9740 |
| Деталь: | CABLE, FUSER DRAWER |
| Парткод: | 40X1049 |
| Деталь: | Cable, fuser drawer (230V only) |
| Парткод: | 40X1050 |
| Деталь: | Board, printer controller |
| Парткод: | 56P2654 |
| Деталь: | EEPROM, printer controller |
| Парткод: | 56P9729 |
| Деталь: | Belt, power supply |
| Парткод: | 40X1052 |
| Деталь: | Fan, power supply |
| Парткод: | 40X1047 |
| Деталь: | Cable asm, conditioning printer controller |
| Парткод: | 40X1205 |
| Деталь: | Motor, paper tray lift |
| Парткод: | 40X1097 |
| Деталь: | Supply, 120V power 2 |
| Парткод: | 56P3986 |
| Деталь: | Supply, 230V power 2 |
| Парткод: | 56P3987 |
| Деталь: | Board, sensor |
| Парткод: | 40X1043 |
| Деталь: | Cable asm, sensor board |
| Парткод: | 40X1044 |
| Деталь: | Cable, belt relay |
| Парткод: | 40X1120 |
| Деталь: | Switch, power |
| Парткод: | 40X1158 |
| Деталь: | CABLE, POWER SWITCH |
| Парткод: | 40X1157 |
| Деталь: | Board, 120V motor driver |
| Парткод: | 56P2652 |
| Деталь: | Board, 230V motor driver |
| Парткод: | 56P2653 |
| Деталь: | Cable asm, MIF |
| Парткод: | 40X1055 |
| Деталь: | Bushing, turn guide |
| Парткод: | 40X1103 |
| Деталь: | Shaft, changing |
| Парткод: | 40X1119 |
| Деталь: | Assembly, drive link |
| Парткод: | 40X1112 |
| Деталь: | Sensor, humidity (not included in 7-3) |
| Парткод: | 40X1247 |
| Деталь: | Clutch, paper feed |
| Парткод: | 40X1082 |
| Деталь: | Clutch, roller 6 x 10 x 14 |
| Парткод: | 40X1081 |
| Деталь: | Assembly, paper-feed base |
| Парткод: | 40X1075 |
| Деталь: | Sensor, relay |
| Парткод: | 40X1107 |
| Деталь: | Roller, relay |
| Парткод: | 40X1108 |
| Деталь: | Roller, separator |
| Парткод: | 40X1079 |
| Деталь: | Clip, paper-feed shaft |
| Парткод: | 40X1106 |
| Деталь: | Clutch, friction (torque limiter) |
| Парткод: | 40X1080 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | 40X1078 |
| Деталь: | Roller, pickup |
| Парткод: | 40X1077 |
| Деталь: | Interrupt, photo |
| Парткод: | 40X1173 |
| Деталь: | Cable asm, paper-feed type 1 |
| Парткод: | 40X1098 |
| Деталь: | Plate, guide rocking |
| Парткод: | 40X1076 |
| Деталь: | FOOT, RUBBER |
| Парткод: | 56P9503 |
| Деталь: | Actuator, front cover open switch |
| Парткод: | 56P9641 |
| Деталь: | Screw, slide rail |
| Парткод: | 56P9524 |
| Деталь: | Rail, base left side |
| Парткод: | 40X1034 |
| Деталь: | Board, CK2 daughter board/sensor |
| Парткод: | 40X1083 |
| Деталь: | Lever, size sense |
| Парткод: | 56P9521 |
| Деталь: | Unit, drive 120 V |
| Парткод: | 56P2666 |
| Деталь: | Unit, drive 230V |
| Парткод: | 56P2667 |
| Деталь: | Clutch, drive unit |
| Парткод: | 40X1150 |
| Деталь: | Cable asm, drive unit sensor |
| Парткод: | 56P9644 |
| Деталь: | Sensor, drive unit |
| Парткод: | 56P9645 |
| Деталь: | Clutch, belt up/down |
| Парткод: | 40X1037 |
| Деталь: | Frame, sub |
| Парткод: | 56P2668 |
| Деталь: | Assembly, jogging unit |
| Парткод: | 56P9300 |
| Деталь: | Belt, timing 60S3M408 |
| Парткод: | 56P9333 |
| Деталь: | Assembly, tractor motor |
| Парткод: | 56P9329 |
| Деталь: | Assembly, guide stack |
| Парткод: | 56P9301 |
| Деталь: | Assembly, elevator motor |
| Парткод: | 56P9308 |
| Деталь: | SHUTTER |
| Парткод: | 56P9451 |
| Деталь: | Spring, C |
| Парткод: | 56P9332 |
| Деталь: | WIRE |
| Парткод: | 56P9331 |
| Деталь: | Drum, wire |
| Парткод: | 56P9459 |
| Деталь: | Gear, Z30 |
| Парткод: | 56P9460 |
| Деталь: | Panel, lower left |
| Парткод: | 56P4073 |
| Деталь: | Assembly, sensor |
| Парткод: | 56P9465 |
| Деталь: | Assembly, hook rear |
| Парткод: | 56P9307 |
| Деталь: | Cover assembly, front |
| Парткод: | 40X1123 |
| Деталь: | Label, MPT |
| Парткод: | 40X1516 |
| Деталь: | Parts packet |
| Парткод: | 40X1262 |
| Деталь: | Cover assembly, right side |
| Парткод: | 40X1124 |
| Деталь: | COVER, TOP |
| Парткод: | 40X1131 |
| Деталь: | Label, operator panel |
| Парткод: | 56P9545 |
| Деталь: | Magnet, right side latch |
| Парткод: | 40X1139 |
| Деталь: | OPERATOR PANEL |
| Парткод: | 40X1259 |
| Деталь: | Cover, waste toner bottle |
| Парткод: | 40X1132 |
| Деталь: | Magnet, front cover latch |
| Парткод: | 40X1140 |
| Деталь: | COVER, LEFT FRONT |
| Парткод: | 40X1129 |
| Деталь: | Cover, left side |
| Парткод: | 40X1126 |
| Деталь: | COVER, SOLENOID |
| Парткод: | 40X1125 |
| Деталь: | Tray assembly, exit |
| Парткод: | 40X1122 |
| Деталь: | COVER, REAR |
| Парткод: | 40X1128 |
| Деталь: | Cover, adjustment |
| Парткод: | 40X1130 |
| Деталь: | COVER, PAPER FEED |
| Парткод: | 40X1127 |
| Деталь: | SPRING, PRESSURE |
| Парткод: | 56P9883 |
| Деталь: | Interrupter, photo |
| Парткод: | 56P9528 |
| Деталь: | Bracket, rear idler |
| Парткод: | 56P9888 |
| Деталь: | BELT, TIMING |
| Парткод: | 56P9884 |
| Деталь: | Gear, drive |
| Парткод: | 56P9886 |
| Деталь: | Pulley, timing |
| Парткод: | 56P9885 |
| Деталь: | Motor, HCF DC |
| Парткод: | 56P9882 |
| Деталь: | Bracket, front idler |
| Парткод: | 56P9887 |
| Деталь: | Parts packet |
| Парткод: | 56P9962 |
| Деталь: | Parts packet |
| Парткод: | 40X1265 |
| Деталь: | Pin, upper unit support |
| Парткод: | 56P9667 |
| Деталь: | HANDLE, LOCK |
| Парткод: | 56P9669 |
| Деталь: | Shroud, cable |
| Парткод: | 56P9670 |
| Деталь: | GUIDE, CABLE |
| Парткод: | 56P9671 |
| Деталь: | Support assembly, upper unit |
| Парткод: | 40X1207 |
| Деталь: | Handle assembly, lock |
| Парткод: | 40X1208 |
| Деталь: | Cover, electronic |
| Парткод: | 40X1151 |
| Деталь: | GUIDE, CABLE |
| Парткод: | 56P9672 |
| Деталь: | Sensor assembly, photo |
| Парткод: | 56P9854 |
| Деталь: | Interrupter, photo |
| Парткод: | 56P9855 |
| Деталь: | Caster, HCF |
| Парткод: | 56P9529 |
| Деталь: | SPRING, TENSION |
| Парткод: | 56P9856 |
| Деталь: | SWITCH, MICRO |
| Парткод: | 56P9857 |
| Деталь: | SWITCH, PUSH |
| Парткод: | 56P9530 |
| Деталь: | Connector, inlet |
| Парткод: | 56P9859 |
| Деталь: | Connector, I/F |
| Парткод: | 56P9858 |
| Деталь: | Screw, Shoulder |
| Парткод: | 56P9853 |
| Деталь: | Parts packet |
| Парткод: | 56P9960 |
| Деталь: | COVER, TOP |
| Парткод: | 56P4064 |
| Деталь: | COVER, FRONT |
| Парткод: | 56P4065 |
| Деталь: | Tray, upper |
| Парткод: | 56P4067 |
| Деталь: | Tray, lower |
| Парткод: | 56P4068 |
| Деталь: | Panel, left upper |
| Парткод: | 56P4062 |
| Деталь: | Assembly, lower left panel |
| Парткод: | 40X1227 |
| Деталь: | COVER, REAR |
| Парткод: | 56P4066 |
| Деталь: | Assembly, staple cover |
| Парткод: | 56P4063 |
| Деталь: | Cover, staple A |
| Парткод: | 56P9365 |
| Деталь: | Cartridge, staple |
| Парткод: | 56P9367 |
| Деталь: | Stapler |
| Парткод: | 56P9363 |
| Деталь: | Cover, staple B |
| Парткод: | 56P9364 |
| Деталь: | Cassette, paper feed |
| Парткод: | 40X4058 |
| Деталь: | Kit, rack guard holder |
| Парткод: | 40X1501 |
| Деталь: | Flag, bottom sense |
| Парткод: | 40X1105 |
| Деталь: | Magnet, front cover latch |
| Парткод: | 40X1140 |
| Деталь: | Spring, paper carry 2 |
| Парткод: | 40X1071 |
| Деталь: | Bushing, pressure |
| Парткод: | 40X1070 |
| Деталь: | Roller, follow up |
| Парткод: | 40X1072 |
| Деталь: | Guide assembly, expansion turn guide |
| Парткод: | 40X1069 |
| Деталь: | Assembly, paper feed expansion |
| Парткод: | 40X1086 |
| Деталь: | Plate, guide rocking |
| Парткод: | 40X1076 |
| Деталь: | Roller, relay expansion feed |
| Парткод: | 40X1111 |
| Деталь: | Guide, HCPF |
| Парткод: | 56P9788 |
| Деталь: | Bushing, turn guide |
| Парткод: | 40X1103 |
| Деталь: | Clip, paper feed shaft |
| Парткод: | 40X1106 |
| Деталь: | Roller, separator |
| Парткод: | 40X1079 |
| Деталь: | Clutch, friction |
| Парткод: | 40X1080 |
| Деталь: | Roller, pickup |
| Парткод: | 40X1077 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | 40X1078 |
| Деталь: | Assembly, turn guide switch option |
| Парткод: | 40X1088 |
| Деталь: | Interrupt, photo |
| Парткод: | 40X1173 |
| Деталь: | Cable asm, paper feed type 2 |
| Парткод: | 40X1089 |
| Деталь: | Sensor, relay |
| Парткод: | 40X1107 |
| Деталь: | Clutch, roller 6 x 10 x 14 |
| Парткод: | 40X1081 |
| Деталь: | Clutch, paper feed |
| Парткод: | 40X1087 |
| Деталь: | Parts packet |
| Парткод: | 40X1270 |
| Деталь: | Guide assembly, turn |
| Парткод: | 40X1242 |
| Деталь: | Duplex assembly |
| Парткод: | 56P4023 |
| Деталь: | Board, duplex interface |
| Парткод: | 40X1060 |
| Деталь: | Frame, duplex |
| Парткод: | 40X1168 |
| Деталь: | Cable assembly, duplex connection |
| Парткод: | 56P3990 |
| Деталь: | Screw, duplex mounting |
| Парткод: | 40X1169 |
| Деталь: | Motor, duplex stepping |
| Парткод: | 56P3989 |
| Деталь: | Interrupter, photo |
| Парткод: | 40X1171 |
| Деталь: | Cable assembly, paper detection |
| Парткод: | 56P9806 |
| Деталь: | Plate, duplex guide |
| Парткод: | 56P9994 |
| Деталь: | Cable assembly, duplex interface |
| Парткод: | 56P9807 |
| Деталь: | Parts packet |
| Парткод: | 40X1271 |
| Деталь: | HANDLE |
| Парткод: | 56P4069 |
| Деталь: | Sensor, Photo |
| Парткод: | 56P9380 |
| Деталь: | SPRING |
| Парткод: | 56P9386 |
| Деталь: | Screw, M4 |
| Парткод: | 56P9373 |
| Деталь: | Assembly, exit guide inverter |
| Парткод: | 56P9309 |
| Деталь: | Sensor, Photo |
| Парткод: | 56P9399 |
| Деталь: | Assembly, exit guide straight |
| Парткод: | 56P4364 |
| Деталь: | Unit, 3 hole punch (U.S. only) |
| Парткод: | 56P9313 |
| Деталь: | Unit, 4 hole punch (non U.S.) |
| Парткод: | 56P9314 |
| Деталь: | Kit, punch speed up |
| Парткод: | 56P4072 |
| Деталь: | Exit assembly, face up |
| Парткод: | 40X1026 |
| Деталь: | Feeder assembly, multipurpose |
| Парткод: | 40X1135 |
| Деталь: | Assembly, upper limit sensor |
| Парткод: | 56P9306 |
| Деталь: | Supply, power |
| Парткод: | 56P9303 |
| Деталь: | Cord, Y power |
| Парткод: | 56P9358 |
| Деталь: | Cord, Y power (230 V only) |
| Парткод: | 56P9368 |
| Деталь: | Board, finisher control |
| Парткод: | 56P4365 |
| Деталь: | CABLE |
| Парткод: | 56P9410 |
| Деталь: | Bracket, finisher control board |
| Парткод: | 56P9420 |
| Деталь: | CABLE, INTERFACE |
| Парткод: | 56P9357 |
| Деталь: | Cable assembly, 30 pin RIP harness |
| Парткод: | 40X1074 |
| Деталь: | Cable assembly, 36 pin RIP harness |
| Парткод: | 40X1073 |
| Деталь: | Cable assembly, 8 pin PH controller |
| Парткод: | 40X1068 |
| Деталь: | Cable assembly, printhead controller power |
| Парткод: | 56P9720 |
| Деталь: | Cable assembly, paper tray lift motor |
| Парткод: | 40X1099 |
| Деталь: | Cable assembly, cassette bottom sensor |
| Парткод: | 40X1100 |
| Деталь: | Cable assembly, paper feed type 1 |
| Парткод: | 40X1098 |
| Деталь: | Cable assembly, carrying clutch |
| Парткод: | 40X1114 |
| Деталь: | Cable assembly, MPF clutch |
| Парткод: | 40X1116 |
| Деталь: | Cable assembly, registration clutch |
| Парткод: | 40X1113 |
| Деталь: | Cable assembly, registration sensor |
| Парткод: | 40X1115 |
| Деталь: | Parts packet |
| Парткод: | 40X1267 |
| Деталь: | Catch, door |
| Парткод: | 56P9838 |
| Деталь: | Magnet, latch |
| Парткод: | 56P9835 |
| Деталь: | COVER, UPPER |
| Парткод: | 56P9837 |
| Деталь: | COVER, UPPER REAR |
| Парткод: | 56P9834 |
| Деталь: | COVER, LOWER REAR |
| Парткод: | 56P9843 |
| Деталь: | COVER, RIGHT |
| Парткод: | 56P9839 |
| Деталь: | COVER, FRONT |
| Парткод: | 56P9833 |
| Деталь: | Fence, end |
| Парткод: | 56P9836 |
| Деталь: | Ring, snap |
| Парткод: | 56P9940 |
| Деталь: | Cover assembly, upper |
| Парткод: | 56P9841 |
| Деталь: | Lever, vertical transport |
| Парткод: | 56P9840 |
| Деталь: | SPRING, TENSION |
| Парткод: | 56P9842 |
| Деталь: | Parts packet |
| Парткод: | 56P9958 |
| Деталь: | Screw, thumb |
| Парткод: | 56P9467 |
| Деталь: | Bracket, rail |
| Парткод: | 40X1237 |
| Деталь: | Screw, lock |
| Парткод: | 56P9472 |
| Деталь: | Screw, rail |
| Парткод: | 40X1238 |
| Деталь: | Chassis, rail |
| Парткод: | 40X1239 |
| Деталь: | ROLLER |
| Парткод: | 56P9474 |
| Деталь: | Stud, lock-f |
| Парткод: | 40X1241 |
| Деталь: | Stud, lock |
| Парткод: | 56P9473 |
| Деталь: | Screw, lock |
| Парткод: | 40X1240 |
| Деталь: | Bracket, lock |
| Парткод: | 40X1254 |
| Деталь: | Shield, light (used on p/n 56P9594) |
| Парткод: | 56P9993 |
| Деталь: | Parts packet |
| Парткод: | 40X4263 |
| Деталь: | FRAME, UPPER |
| Парткод: | 56P9594 |
| Деталь: | Holder, cable |
| Парткод: | 56P9638 |
| Деталь: | Shroud, cable |
| Парткод: | 56P9632 |
| Деталь: | Board, printhead controller |
| Парткод: | 56P3980 |
| Деталь: | Pivot, color link |
| Парткод: | 56P9628 |
| Деталь: | BEARING, ROLLER |
| Парткод: | 56P9627 |
| Деталь: | Link, frame |
| Парткод: | 56P9624 |
| Деталь: | Frame, printhead controller |
| Парткод: | 40XH49 |
| Деталь: | Hook, right link |
| Парткод: | 56P9625 |
| Деталь: | Holder, front hsp |
| Парткод: | 40XH42 |
| Деталь: | Holder, front printhead |
| Парткод: | 56P9644 |
| Деталь: | Rail, left side |
| Парткод: | 56P9592 |
| Деталь: | Rail, right side |
| Парткод: | 56P9640 |
| Деталь: | Link, frame |
| Парткод: | 56P9629 |
| Деталь: | Cover, eraser |
| Парткод: | 56P9594 |
| Деталь: | Holder, rear printhead |
| Парткод: | 56P9593 |
| Деталь: | Spring, printhead |
| Парткод: | 56P9609 |
| Деталь: | Bracket, rear upper |
| Парткод: | 40XH48 |
| Деталь: | Fan, upper left |
| Парткод: | 40X4033 |
| Деталь: | Bracket, fan holder |
| Парткод: | 56P9624 |
| Деталь: | Fan, upper right |
| Парткод: | 40X4032 |
| Деталь: | Cover, hook |
| Парткод: | 56P9626 |
| Деталь: | Assembly, RFID |
| Парткод: | 40Xm7 |
| Деталь: | Hook, middle |
| Парткод: | 40XH45 |
| Деталь: | HOOK, RIGHT |
| Парткод: | 40XH47 |
| Деталь: | Handle, up opening |
| Парткод: | 40X4257 |
| Деталь: | Bracket, front upper |
| Парткод: | 40XH43 |
| Деталь: | HOOK, LEFT |
| Парткод: | 40XH46 |
| Деталь: | Rod, interlocking |
| Парткод: | 40XH44 |
| Деталь: | Hook, left link |
| Парткод: | 56P9630 |
| Деталь: | Cable, RFID |
| Парткод: | 40Xm8 |
| Деталь: | Lamp, M erase |
| Парткод: | 40X4028 |
| Деталь: | Lamp, C erase |
| Парткод: | 40X4029 |
| Деталь: | Lamp, Y erase |
| Парткод: | 40X4030 |
| Деталь: | Lamp, K erase |
| Парткод: | 40X4034 |
| Деталь: | Assembly, LED printhead (K) |
| Парткод: | 56P3984 |
| Деталь: | Assembly, LED printhead (C) |
| Парткод: | 56P3982 |
| Деталь: | Assembly, guide plate |
| Парткод: | 56P9395 |
| Деталь: | Assembly, solenoid |
| Парткод: | 56P9334 |
| Деталь: | Spring, H |
| Парткод: | 56P9396 |
| Деталь: | Gear, Z19 |
| Парткод: | 56P9398 |
| Деталь: | GATE |
| Парткод: | 56P9310 |
| Деталь: | ROLLER |
| Парткод: | 56P9400 |
| Деталь: | Roller, patting |
| Парткод: | 56P9361 |
| Деталь: | Roller, I |
| Парткод: | 56P9401 |
| Деталь: | Roller, F |
| Парткод: | 56P9312 |
| Деталь: | Roller, G |
| Парткод: | 56P9405 |
| Деталь: | CLUTCH, REGISTRATION |
| Парткод: | 56P9335 |
| Деталь: | Belt, timing 60S2M184 |
| Парткод: | 56P9407 |
| Деталь: | Assembly, feed motor |
| Парткод: | 56P9341 |
| Деталь: | Belt, timing 60S2M334 |
| Парткод: | 56P9339 |
| Деталь: | Assembly, punch drive |
| Парткод: | 56P4060 |
| Деталь: | Spring, B |
| Парткод: | 56P9318 |
| Деталь: | Pulley gear Z36/T24 |
| Парткод: | 56P4070 |
| Деталь: | BELT |
| Парткод: | 56P4061 |
Коды ошибок
900
910
911
912
917
918
919
920
923
924
925
926 ... 929
930
931
932
933
934
935
936 ... 939
940
941
942
945
946
947
948
949
950
952
954
955
956
957
958
960
961
964
970
975
976
978
979
980
981
982
983
984
985
986
987
991
992
993
994
995
996
997
998
999
Описание
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 910 |
| Display: | SYSTEM HALT (*) 910 : DEVICE CONST |
| Description: | Tray 2 Lift Motor Failure Code 910: The Tray 2 Lift Motor is not rotating. |
| Causes: | • Tray 2 Lift Motor, PL4.1.23 • Motor Driver Board, PL2.1.10 • LVPS, PL3.1.1 |
| Remedy: | 1 Test the Lift Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Tray 2 Lift Motor test. Does the motor operate? Complete. Replace the motor. If the error persists, go to Step 2. 2 Check for +24 V to the Lift Motor. Is there +24 V across GDDC-1 <=> ground? Go to Step 5. Go to Step 3. 3 Check Motor Driver Board POW24 connector for 24 V. 1. Disconnect POW24. Is there +24 V across POW24 pins 1 and 2? Replace the Motor Driver Board. Go to Step 4. 4 Check for 24 V at the LVPS 1. Disconnect CN2 on the LVPS. Is there +24 V across pins 1 and 2? Replace the POW24 Harness. Replace the LVPS. 5 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 911 |
| Display: | ERROR 911 ENVIRONMENT TEMP(HI) |
| Description: | DC pick motor excessive PWM |
| Remedy: | • Check system board • Check autocompensator motor |
| Error code: | 912 |
| Description: | DC pick motor underspeed error |
| Remedy: | • Check system board • Check autocompensator |
| Error code: | 917 |
| Display: | Power Off/on 917: Error |
| Description: | Error in the Transfer Unit Belt Applicable Status Code: Code 917: The Transfer Belt Rotation Sensor indicates a belt error. |
| Causes: | • Transfer Unit, PL1.1.20 • Transfer Unit Motor, PL2.1.86 • Belt Rotation Sensor, PL2.1.146 |
| Remedy: | 1 Test the Belt Rotation Sensor. Run the Service Diagnostics Belt Hole IC test. Does the sensor function correctly? Go to Step 2. Replace the sensor (8-91). If the error persists, go to Step 3. 2 Test the Transfer Unit Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Transfer Belt Motor test. Does the motor operate? Replace the Transfer Unit. If the error persists, go to Step 3. Replace the motor. If the error persists, go to Step 3. 3 Check all pins on the HALL1 Harness for continuity. Disconnect HALL1 and P/J310 Is the harness conductive? Replace the Motor Driver Board.If the error persists, go to Step 4. Replace the HALL1 Harness. 4 Check all pins of the DRV0 harness for continuity. Disconnect the DRV0 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV0 Harness. |
| Error code: | 918 |
| Display: | Power Off/on 918: Error |
| Description: | Duplex Unit Fan Failure The Duplex Fan rotation signal indicates the Duplex Fan has stopped rotating. Applicable Status Code: Code 918: The Duplex Fan has failed. |
| Causes: | • Duplex Unit Fan • Duplex Unit Control Board • Duplex Unit |
| Remedy: | 1 Check the Duplex Unit connector for damage. Is the connector damaged? Replace the connector. Go to Step 2. 2 Test the Duplex Unit Fan. Run the Service Diagnostics Duplex Fan test. Does the Fan function correctly? Go to Step 3. Replace the Duplex Unit. If the error persists, go to Step 3. 3 Check all pins on the DUPLEX Harness for continuity. Disconnect the DUPLEX Harness. Is the DUPLEX Harness conductive? Replace the Motor Driver Board. If the error persists, go to Step 4. Replace the DUPLEX Harness. 4 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 919 |
| Display: | Power Off/on 919: Error |
| Description: | Power Supply Fan Error |
| Causes: | • Controller RW3600 power outtage • Controller RW3600 rebooted • Connection to Controller RW3600 loose |
| Remedy: | 1 Is CN17 on the printer controller board properly connected? Go to step 2. Connect CN17. 2 Is CN6 on the CK2 daughter board properly connected? Go to step 3. Connect CN6. 3 Is +24 V present between pins 1 and 3 of connector CN6 on the CK2 daughter board? Replace the power supply fan. Replace the printer controller board. 4 Did either exchange solve the problem? Problem solved. Replace the CK2 daughter board. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 923 |
| Display: | Power Off/on 923: Error |
| Description: | Fuser Error |
| Remedy: | Fuser is too hot during printing or when printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 924 |
| Display: | Power Off/on 924: Error |
| Description: | Fuser Error |
| Causes: | • Non-supported DRAM connected • Poor connection between IMB and optional DRAM • Optional DRAM defective • IMB defective • BiCU defective |
| Remedy: | An open circuit has been detected in the Fuser Thermistor Circuit. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 926 ... 929 |
| Description: | 926(K), 927(C), 928(Y), 929(M) - Toner Sensor Error |
| Remedy: | 1 Is the toner cartridge the correct type for the printer? Go to step 2. Recommend the customer replace the cartridge with the correct type. 2 Is the toner cartridge encoder wheel dirty? Clean the encoder wheel and toner sensor. Go to step 3. 3 Replace the toner cartridge for the color with the error. Did this fix the problem? Problem solved. Go to step 4. 4 Test the sensors. While actuating the sensor, does the voltage fluctuate between 0 V and +5 V between pins 1 and 4 and 5, 8 and 9, 12, and 13 on CN1 on the printer controller board. Replace the printer controller board. Replace the affected toner sensor. |
| Error code: | 930 |
| Display: | Power Off/on 930: Error |
| Description: | Motor Driver Board Clock Frequency Error The Sub-CPU clock frequency on the Motor Driver Board is inaccurate. Applicable Status Code: Code 930: The Sub-CPU clock frequency is inaccurate. |
| Causes: | • Motor Driver Board, PL2.1.10 • Engine Control Board, PL1.1.4 |
| Remedy: | 1 Check the Motor Driver Board connection. Is DRV0 harness damaged or disconnected or? Replace the harness. Go to Step 2. 2 Check all pins of the DRV0 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Motor Driver Board. If the error persists, replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 931 |
| Display: | Power Off/on 931: Error |
| Description: | Duplex Unit Clock Frequency Error The clock frequency for the Duplex Unit Control Board CPU is inaccurate. Applicable Status Code: Code 931: The Duplex Unit’s CPU clock frequency is inaccurate. |
| Causes: | • Motor Driver Board, PL2.1.10 • Duplex Unit, PL16.1.1A |
| Remedy: | 1 Check the Duplex Unit connector for damage. Is the connector damaged? Replace the connector. Go to Step 2. 2 Check all pins on the DUPLEX Harness for continuity. Disconnect the DUPLEX Harness. Is the DUPLEX Harness conductive? Replace the Duplex Unit. If the error persists, go to Step 3. Replace the DUPLEX Harness. 3 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 932 |
| Display: | Power Off/on 932: Error |
| Description: | Finisher Inverter Clock Frequency Error The clock frequency for the Inverter Control Board CPU is inaccurate. Applicable Status Code: Code 932: The Inverter’s CPU clock frequency is inaccurate. |
| Causes: | • Inverter Control Board • Engine Control Board, PL1.1.4 |
| Remedy: | 1 Check the Option connection. Is the Option connection from the Inverter to the Printer damaged or disconnected? Reconnect or replace the cable. Go to Step 2. 2 Check all pins on the Option Harness for continuity. Disconnect OPTIF from the Engine Control Board and the Option connector. Is the harness conductive? Go to Step 3. Replace the Option harness. 3 Check the Inverter Control Board POWER connection. Is POWER disconnected or damaged? Replace or reconnect the harness. Replace the Inverter Control Board. If the error persists, replace the Engine Control Board. |
| Error code: | 933 |
| Display: | Power Off/on 933: Error |
| Description: | Black Printhead Error |
| Remedy: | 1 Check to ensure that the cables between the LED printhead and the printhead controller board as well as the cables between the printhead controller board and the printer controller board are properly connected. Are they properly connected? Go to step 2. Properly connect the cables. 2 Replace the LED printhead for the affected color. Did this resolve the problem? Problem solved. Replace the printhead controller board, and go to step 3. 3 Did replacement of the printhead controller board resolve the problem? Problem solved. Replace the printer controller board. |
| Error code: | 934 |
| Display: | Power Off/on 934: Error |
| Description: | Color Drum Sensor Error |
| Remedy: | 1 Clean the color drum sensor LED. Did this fix the problem? Problem solved. Go to step 2 2 Swap the yellow photo developer with a different color photo developer. Did this fix the problem? Replace the photo developer that called the error. Go to step 3. 3 Is connector CN2 on the printer controller board connected properly? Replace the sub frame assembly. Plug the connector in securely. 4 Did replacing the sub frame fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 935 |
| Display: | Power Off/on 935: Error |
| Description: | Black Drum Sensor Error |
| Remedy: | 1 Clean the black drum sensor LED. Did this fix the problem? Problem solved. Go to step 2 2 Swap the black photo developer with a different color photo developer. Did this fix the problem? Replace the photo developer that called the error. Go to step 3. 3 Is connector CN2 on the printer controller board connected properly? Replace the sub frame assembly. Plug the connector in securely. 4 Did replacing the sub frame fix the problem? Problem solved. Replace the printer controller board |
| Error code: | 936 ... 939 |
| Description: | Cassette Error |
| Remedy: | 1 Are connectors CN8 and CN6 on the printer controller board connected properly? Replace the printer controller board. Plug the connector in securely. |
| Error code: | 940 |
| Display: | Power Off/on 940: Error |
| Description: | Waste Toner Transfer Error The Waste Toner Auger Rotation Sensor indicates that the Waste Toner Auger has stopped rotating. Applicable Status Code: Code 940: The Waste Toner Auger has failed. |
| Causes: | • Waste Toner Auger Rotation Sensor • Waste Toner Auger Assembly • Waste Toner Motor |
| Remedy: | 1 Check the following for evidence of fault or damage: • Waste Toner Manifold • Waste Toner Auger Rotation Sensor • HALLDCT Harness Is there any damage or debris? Replace any damaged parts. Go to Step 2. 2 Test the Waste Toner Auger Rotation Sensor. Run the Service Diagnostics Waste Toner Hole IC test using a magnetic source to actuate the Hall-effect sensor. Does the sensor function correctly? Go to Step 3. Replace the sensor. If the error persists, go to Step 6. 3 Check the Waste Toner Manifold Auger drive. With the Basket Assembly closed, rotate the Waste Toner Motor. Does the Auger rotate? Go to Step 4. Replace the Waste Toner Gear Assembly PL2.1.41. 4 Test the Waste Toner Motor. Run the Service Diagnostics Waste Motor test. Does the motor rotate? Go to Step 7. Replace the motor. If the error persists, go to Step 5. 5 Check all pins of the WTDC Harness for continuity. Disconnect WTDC and P/J50. Is the harness conductive? Replace the Motor Driver Board. Replace the harness. 6 Check all pins of the HALLDCT Harness for continuity. Disconnect HALLDCT and P/J320. Is the harness conductive? Replace the Motor Driver Board. Replace the harness. 7 Check all pins of the DRV0 Harness for continuity. Disconnect DRV0. Is the harness conductive? Replace the Motor Driver Board. If the error persists, replace the Engine Control Board. Replace the harness. |
| Error code: | 941 |
| Display: | Power off/on 941: Error |
| Description: | High-Capacity Feed Tray Error |
| Remedy: | 1 Is connector CN22 on the printer controller board connected properly? Go to “Highcapacity feeder (HCF) service check”. Plug the connector in securely. |
| Error code: | 942 |
| Display: | Power off/on 942: Error |
| Description: | Duplex Error |
| Remedy: | 1 Is connector CN16 on the printer controller board connected properly? Replace the printer controller board. Plug the connector in securely. |
| Error code: | 945 |
| Display: | Power off/on 945: Error |
| Description: | Engine Flash Error |
| Remedy: | Reflash the engine code. |
| Error code: | 946 |
| Display: | Power OFF/ON Error : 946 |
| Description: | Printer/Printhead Controller Board Communication Error |
| Remedy: | 1 Is CN03 on the printhead controller board or CN14 on the printer controller board connected properly? Go to step 2. Connect cables. 2 Make sure all printhead LED EPROMS are present on the printhead controller board. Are all the EPROMS present? Go to step 3. Install the EPROM(s) included with printhead FRU. 3 Replace the printhead controller board. Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 947 |
| Description: | Finisher Communication Error |
| Remedy: | 1 Are the finisher to printer interface cable and power cable properly connected? Go to step 2. Properly connect the cable. 2 Replace the interface cable. Did this resolve the problem? Problem solved. Replace the control finisher board. Go to step 3. 3 Did finisher control board replacement resolve the problem? Problem solved. Replace the printer control board. |
| Error code: | 948 |
| Description: | PEL Clock Error |
| Remedy: | Indicates the pel clock check failed. Replace the system board. |
| Error code: | 949 |
| Description: | Delay Line Calibration Failure |
| Remedy: | Indicates a delay line calibration failure. Replace the system board. |
| Error code: | 950 |
| Description: | NVRAM Mismatch |
| Remedy: | 950 Error displayed on the printer and you are not sure if the printer had the interconnect or system boards previously replaced: 1 Interconnect board Note: Before replacing the interconnect board, make absolutely sure you have the correct FRU number for the interconnect board that should go into your printer. Warning: Any time the interconnect board assembly is replaced, the Configuration ID must be reset in NVRAM on the interconnect board. See “Setting configuration ID”. Unplug the machine and replace the interconnect board assembly. Turn the printer on. If a 950 error still displays, replace the system board assembly. 950 Error after replacing the system board: 1 System board Note: Make sure you have the correct system board FRU number before installing the board in the printer. Replace the system board. 950 Error after replacing interconnect board: 1 Interconnect board Note: Before replacing the interconnect board, make absolutely sure you have the correct FRU number for the interconnect board that should go into your printer. Warning: Any time the interconnect board assembly is replaced, the Configuration ID must be reset in NVRAM on the interconnect board. Go to“Setting configuration ID”. Replace the interconnect board. |
| Error code: | 952 |
| Description: | NVRAM Chip Failure |
| Causes: | An engine board NVM abnormality. Replace the engine board. |
| Remedy: | 1 Make sure the 26-pin RIP printer controller cable is not broken or damaged. Is the cable broken or damaged? Replace the cable. Go to step 2. 2 Is EPROM U7 present on the printer controller board? Replace the printer controller board. Install EPROM U7. |
| Error code: | 954 |
| Description: | NVRAM CRC Failure |
| Causes: | • Firmware bug • IPU defective |
| Remedy: | Indicates the NVRAM experienced a CRC failure. Replace the interconnect board. |
| Error code: | 955 |
| Description: | Code CRC <loc> |
| Causes: | • Firmware bug • Hard disk unit defective • Controller defective • MCU defective • IPU defective |
| Remedy: | Replace the system board. Where <loc> = CRC Failure or ECC Failure on the system board. |
| Error code: | 956 |
| Description: | Processor Failure |
| Causes: | A processor failure on the RIP board. Replace the RIP board. |
| Remedy: | Replace the RIP board. |
| Error code: | 957 |
| Description: | ASIC Failure |
| Causes: | A ASIC failure on the RIP board. Replace the RIP board. |
| Remedy: | Replace the RIP board. |
| Error code: | 958 |
| Description: | NAND Failure |
| Causes: | The printer has performed more than 100 "shift and re-flash" operations as a result of Error Correction Code bit corrections. It is an indication that the NAND on the RIP board is failing. Replace the RIP board. |
| Remedy: | Before proceeding when a 958 NAND failure displays, perform a power on reset (POR) to see if the ECC error correction code can reflash NAND. If this does not fix the problem, replace the system board. |
| Error code: | 960 |
| Display: | Inspection is required. 980:Error |
| Description: | RAM Memory Error |
| Remedy: | Indicates a DRAM Memory Error on the system board. Replace the system board. |
| Error code: | 961 |
| Description: | RAM in Slot 2 is Bad |
| Causes: | The RAM in slot 1 on the RIP board is bad. Replace the failing RAM card. |
| Remedy: | If another SDRAM memory DIMM is installed in slot 1, turn the power off, switch the DIMM in slot 1 to slot 2. If the memory in slot 2 now works correctly, replace the failing DIMM that was in slot 2. If this does not fix the problem, replace the system board. If another DIMM is not available, replace the memory option. If this does not fix the problem, replace the system board. |
| Error code: | 964 |
| Description: | Emulation Error |
| Causes: | • Software defective |
| Remedy: | Indicates a failure within the Download Emulation which is programmed into the code overlay card. The specific error is as follows: 964 - Download Emulation CRC Failure. Checksum Failure. |
| Error code: | 970 |
| Description: | Standard Network Error |
| Remedy: | Check the network card in slot x on the RIP card. |
| Error code: | 975 |
| Description: | Unrecognizable Network Port |
| Causes: | The network port is unrecognizable. For printers equipped with (standard) network circuitry on the RIP board, replace the RIP board. For printers equipped with an optional network card, replace the failing card. |
| Remedy: | Software error. |
| Error code: | 976 |
| Description: | Unrecoverable Software Error in Network Port |
| Causes: | An unrecoverable software error in the network port. For printers equipped with (standard) network circuitry on the RIP board, replace the RIP board. For printers equipped with an optional network card, replace the failing card. |
| Remedy: | Software error. Go to the “Options service check”, and refer to the network card option section. |
| Error code: | 978 |
| Description: | Bad Checksum While Programming Network Card |
| Causes: | A bad checksum while programming the network port. For printers equipped with (standard) network circuitry on the RIP board, replace the RIP board. For printers equipped with an optional network card, replace the failing card. |
| Remedy: | Software error. |
| Error code: | 979 |
| Description: | Flash Parts Failed While Programming Network Port |
| Causes: | Flash parts failed while programming the network port. For printers equipped with (standard) network circuitry on the RIP board, replace the RIP board. For printers equipped with an optional network card, replace the failing card. |
| Remedy: | Reflash network port. |
| Error code: | 980 |
| Display: | Contact the Service center. 980: Error |
| Description: | <device> Comm |
| Causes: | • See description below this table. |
| Remedy: | The engine is experiencing unreliable communications to the specified device. |
| Error code: | 981 |
| Display: | Service call 981: Error |
| Description: | <device> |
| Causes: | • Defective NVRAM • Loose connection between the BICU and the NVRAM • Incorrect installation of the NVRAM • Defective BICU |
| Remedy: | The engine protocol violation detected by the specified device. |
| Error code: | 982 |
| Display: | Service call 982: Error |
| Description: | <device> Comm |
| Causes: | • Localization setting not specified (The main power switch is turned on for the first time after the NVRAM is replaced.) • Incorrect localization setting • Defective NVRAM |
| Remedy: | Communications error detected by the specified device. |
| Error code: | 983 |
| Display: | Power Off/on 983: Error |
| Description: | <device> |
| Causes: | Is more than one toner cartridge of the same color installed? |
| Remedy: | Invalid command received by the specified device. |
| Error code: | 984 |
| Display: | Service call 984: Error. |
| Description: | <device> |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected |
| Remedy: | Invalid command parameter received by the specified device. Note: Service errors 980 thru 984 <device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 985 |
| Display: | Service call 985: Error |
| Description: | Transfer Belt Thermistor Error |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected |
| Remedy: | 1 Are connectors CN407 and CN411 on the sensor board connected properly? Go to step 2. Plug the connector in securely. 2 Is connector CN15 on the printer controller board connected properly? Replace the transfer belt unit. If the problem remains, replace the printer controller board. Plug the connector in securely. |
| Error code: | 986 |
| Display: | Service call 986: Error |
| Description: | Transparency (OHP) Sensor Error |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU Controller disconnected |
| Remedy: | 1 Are connectors CN4 (light emitting) and CN5 (light receiving) on the CK1 daughter board connected properly? Go to step 2. Plug the connector in securely. 2 Test the sensor. While actuating the sensor, does the voltage fluctuate between 0 V and +5 between pins 2 and 3 of connector CN7 of the printer controller board? Replace the printer controller board. Replace the MPF unit. |
| Error code: | 987 |
| Display: | Service call 987: Error |
| Description: | Service Toner Cartridge |
| Remedy: | 1 Turn the printer off and then back on. Did this fix the error? Problem solved. Go to step 2. 2 Try different toner cartridges. Did this fix the error? Problem solved. Go to step 3. 3 Check the cable connections on the RFID antenna, and CN 21 on the printer controller card. Are they properly connected? Go to step 4. Properly connect the connections. 4 Check the RFID cable. Is it damaged? Replace the RFID cable. Replace the printer controller board. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 993 |
| Display: | Service Call 993:Error |
| Description: | CPU Error |
| Remedy: | Replace the printer controller board. |
| Error code: | 994 |
| Display: | Service Call 994:Error |
| Description: | Density Sensor Error |
| Causes: | • No action required because this SC does not interfere with operation of the machine. |
| Remedy: | 1 Is the front door fully closed? Go to step 2. Close the front door. 2 Is the density sensor actuator stuck in place? Release the density sensor actuator. Go to step 3. 3 Are connectors CN406 and CN407 on the sensor board connected properly? Go to step 4. Plug the connector in securely. 4 Is connector CN15 on the printer controller board connected properly? Replace the density sensor. Go to step 5. Plug the connector in securely. 5 Did replacing the density sensor fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 995 |
| Description: | Finisher Main Feed Motor abnormal |
| Causes: | -01 D • Defective BCU • NVRAM Replacement error • Install the previous NVRAM • Input the serial number with SP5-811-004, and turn the main power switch off and on. -02 D • Defective NVRAM • Defective controller Perform SP5-825 to download the appropriate data to the NVRAM, and then turn the main power switch off and then back on. -03 D The serial number cannot be identified due to a mistake during controller replacement or mechanical failure. Replace the controller with the correct type. -04 D - Place all parts in the initial state, and then replace the parts according to the procedures described in the manuals. |
| Remedy: | 1 Is there jammed paper or other obstructions in the paper path? Clear the paper path. Go to step 2. 2 Check to ensure the connector PJ6 on the finisher control board and the feed motor assembly cable are properly connected. Are the cables properly connected? Go to step 3. Properly connect the cables. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pins 7 and 8 and +5 V dc (–10%) between pins 7 and 6 on the feed motor assembly cable connector CN1. Is either voltage missing? Go to step 4. Go to step 5. 4 Disconnect the feed motor assembly cable and PJ6 on the finisher control board. Measure continuity on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 5 Replace the feed motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 6 Measure for +24 V dc between pins 1 and 2 on connector PJ3 on the finisher control board. Measure for +5 V dc between pins 1 and 3 on PJ2 on the finisher control board. Is either voltage missing? Replace the power supply. Replace the finisher control board. |
| Error code: | 996 |
| Description: | Finisher Jogging Motor Error |
| Causes: | • FCU board hardware or firmware defective • Replace FCU board |
| Remedy: | 1 Are there foreign objects or obstructions in the jogging assembly? Clear the objects or obstruction. Go to step 2. 2 Are the jogging motor connectors CN2 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pin 1 on CN2 and frame ground. Is +24 V dc present? Go to step 4. Go to step 5. 4 Replace the jogging motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN2 and PJ5. Perform a continuity check on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 6 Check for +24 V dc (–10%) between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
| Error code: | 999 |
| Display: | Service call 999: Error |
| Description: | Stapler Motor Error |
| Causes: | • Color registration (MUSIC) failure |
| Remedy: | 1 Are staples jammed in the stapler? Go to step 2. Go to step 3. 2 Clear the staple jam and run the staple test in diagnostic mode or run a staple job. Does the problem reoccur? Replace the staple cartridge and to go step 4. Problem solved. 3 Are the connectors CN5 on the stapler and PJ1 on the finisher control board securely connected? Go to step 5. Securely connect the connectors. 4 Did replacement of the stapler cartridge resolve the problem? Problem resolved. Replace the stapler. 5 Make sure the finisher set switch is activated. Measure for 5 V dc between pins 11 and 12 on stapler connector CN5. Is 5 V dc present? Replace the stapler. Replace the finisher control board. 6 Did replacement of the finisher control board correct the problem? Problem solved. Go to step 7. 7 Is there continuity on the stapler to finisher control board cable? Replace the power supply. Replace the cable. |
