Toshiba e-Studio 45
Рейтинг
Модули
ASM-BYPASS-FEEDER-2
ASM-FUSER-2
ASM-FEEDER-1
ASM-FUSER-1
ASM-COVER-2
ASM-BASE-FRAME
ASM-CASE-PWA
ASM-CHARGER-M
ASM-FUSER-3
ASM-CLEANER
ASM-COVER-1
ASM-CRG-2
ASM-CASSETTE
ASM-BYPASS
ASM-CONTROL-PANEL
ASM-TONER
ASM-ADU
ASM-OPTICS-FRAME
ASM-FUSER-4
ASM-PLATEN
ASM-REAR-FRAME
ASM-DEV-STAY
ASM-COVER-GUIDE
ASM-CRG-1
ASM-MAIN-DRIVE
ASM-FEEDER-2
ASM-LASER-SCAN
ASM-FRONT-FRAME
ASM-BYPASS-FEEDER-1
ASM-CHARGER-TR
ASM-OPTICS-DRIVE
ASM-ALGINING
ASM-DEVELOPER
Детали ASM-CRG-1
| Деталь: | SHAFT-BYP-320 |
| Парткод: | 44201954000 |
| Деталь: | BRKT-ROL-BYP |
| Парткод: | 41316535000 |
| Деталь: | K-BRKT-PICK-BYP |
| Парткод: | 41316537000 |
| Деталь: | COLLAR-BYPASS |
| Парткод: | 4401965280 |
| Деталь: | LEVER-PICK |
| Парткод: | 4401965310 |
| Деталь: | SLEEVE-BYPS-AW |
| Парткод: | 41316521000 |
| Деталь: | SPR-0.8-13.82-R |
| Парткод: | 4401966620 |
| Деталь: | ARBOR-PICK-UP |
| Парткод: | 4401965300 |
| Деталь: | PLY/T-2GT020-06 |
| Парткод: | 4401966400 |
| Деталь: | BLT/T142-2GT2.8 |
| Парткод: | 4401965220 |
| Деталь: | K-ROL-FEED-1 |
| Парткод: | 4402038460 |
| Деталь: | CLUTCH-6-L |
| Парткод: | 4402833110 |
| Деталь: | SFT-PICK-BYP |
| Парткод: | 41316549000 |
| Деталь: | STPR-PA-BYP-R |
| Парткод: | 41316529000 |
| Деталь: | K-ROLL-PICK-BYP |
| Парткод: | 4401966500 |
| Деталь: | K-FRM-ROL-BYP |
| Парткод: | 41316647000 |
| Деталь: | ARM-STOPPER |
| Парткод: | 4401965270 |
| Деталь: | GUIDE-PA-L-BYP |
| Парткод: | 41316649000 |
| Деталь: | GUIDE-PA-R-BYP |
| Парткод: | 41316650000 |
| Деталь: | K-SZ-ACTR-BYP |
| Парткод: | 41316525000 |
| Деталь: | ACT-PAPER-SW-BP |
| Парткод: | 41316530000 |
| Деталь: | SZ-GP1A73A |
| Парткод: | 4408683480 |
| Деталь: | BUSH-6-3.7 |
| Парткод: | 4401966470 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | CLP/W-UAMS05L |
| Парткод: | 4843391176 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | STPR-PA-BYP-F |
| Парткод: | 41316528000 |
| Деталь: | STP-ARM-SUB-R |
| Парткод: | 41316624000 |
| Деталь: | STP-ARM-SUB-F |
| Парткод: | 41316623000 |
| Деталь: | WEIGHT-PICK-FAC |
| Парткод: | 41316654000 |
| Деталь: | WEIGHT-PICK-BAC |
| Парткод: | 41316655000 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | ERR030SKZN3A |
| Парткод: | 4842090310 |
| Деталь: | 9HSS40/06MSFB |
| Парткод: | 4842011083 |
| Деталь: | TBID3006MSZN3A |
| Парткод: | 4842040683 |
| Деталь: | ERR050SKZN3A |
| Парткод: | 4842090312 |
| Деталь: | FLT3008MSZN3AI |
| Парткод: | 4842041964 |
| Деталь: | HOLDER-PICK-BYP |
| Парткод: | 41316541000 |
| Деталь: | CUSH-PICK-BYP |
| Парткод: | 44201955000 |
| Деталь: | SPRING-ROL-BYP |
| Парткод: | 41316656000 |
| Деталь: | SPR-0.8-13.82-R |
| Парткод: | 4401967500 |
| Деталь: | CLUTCH-6-08L2 |
| Парткод: | 4406584800 |
| Деталь: | K-FRM-ROL-BYP |
| Парткод: | 41316663000 |
| Деталь: | HR-3500-L |
| Парткод: | 44299020000 |
| Деталь: | BRG6808ZZNRS1C4 |
| Парткод: | 44202938000 |
| Деталь: | GEAR-H/R-320 |
| Парткод: | 44202940000 |
| Деталь: | CRR-H/R-320 |
| Парткод: | 44202941000 |
| Деталь: | HR-3500-U |
| Парткод: | 44299019000 |
| Деталь: | BRG608ZZM4 |
| Парткод: | 44202925000 |
| Деталь: | K-FRM-FUS-PRS |
| Парткод: | 44202900000 |
| Деталь: | SHAFT-CLN-P/R |
| Парткод: | 44202985000 |
| Деталь: | BUSH-CLN-PRS |
| Парткод: | 44202988000 |
| Деталь: | SCRAPER-P/R |
| Парткод: | 44202943000 |
| Деталь: | SPC-CLN-P/R |
| Парткод: | 44202987000 |
| Деталь: | DUCT-FUSER |
| Парткод: | 44203070000 |
| Деталь: | FAN-HTR-320 |
| Парткод: | 44205181000 |
| Деталь: | COVER-FUSER-FAN |
| Парткод: | 44203071000 |
| Деталь: | SEAL-DUCT-FUS-1 |
| Парткод: | 44203072000 |
| Деталь: | SEAL-DUCT-FUS-2 |
| Парткод: | 44203073000 |
| Деталь: | LBL-HOT |
| Парткод: | 44204538000 |
| Деталь: | STOPPER-SFT-CLN |
| Парткод: | 44202990000 |
| Деталь: | STAY-GUIDE-SCRP |
| Парткод: | 44203094000 |
| Деталь: | SPE-SCRAPER-50 |
| Парткод: | 44203109000 |
| Деталь: | ERR060SKZN3A |
| Парткод: | 4842090313 |
| Деталь: | PTBR3012MSZN3A |
| Парткод: | 4842040848 |
| Деталь: | BID2506MSCR1AI |
| Парткод: | 4842041869 |
| Деталь: | SCRAPER-P/R |
| Парткод: | 44203114000 |
| Деталь: | BID3006MSCR1AI |
| Парткод: | 4842041899 |
| Деталь: | frame-feed-unit |
| Парткод: | 44201780000 |
| Деталь: | BRKT-ROL-SEP |
| Парткод: | 41318614000 |
| Деталь: | guide-p-sep |
| Парткод: | 41318623000 |
| Деталь: | hldr-sep-rol-dm |
| Парткод: | 44201805000 |
| Деталь: | lev-rol-sep-dm |
| Парткод: | 44201810000 |
| Деталь: | arbor-spt-r-320 |
| Парткод: | 44201813000 |
| Деталь: | cov-spe/arbor |
| Парткод: | 4401966980 |
| Деталь: | K-ROLL-SPT |
| Парткод: | 4400669910 |
| Деталь: | shaft-sep |
| Парткод: | 4401964250 |
| Деталь: | arbor-spt-f-320 |
| Парткод: | 44201812000 |
| Деталь: | k-shaft-feed |
| Парткод: | 44201802000 |
| Деталь: | ASM-CLT-G28-CC6 |
| Парткод: | 4401969940 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | k-brkt-clt |
| Парткод: | 44201782000 |
| Деталь: | GROMET-EHP-6 |
| Парткод: | 4842416025 |
| Деталь: | k-arm-pick-roll |
| Парткод: | 44201786000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | K-ROL-PICK-2 |
| Парткод: | 44201807000 |
| Деталь: | STOP-RING-6-1.5 |
| Парткод: | 44201801000 |
| Деталь: | GEAR-06S-032-06 |
| Парткод: | 44201789000 |
| Деталь: | SPE040-030-0226 |
| Парткод: | 44201790000 |
| Деталь: | lever-pick-roll |
| Парткод: | 44201788000 |
| Деталь: | act-near-empty |
| Парткод: | 44201792000 |
| Деталь: | act-empty |
| Парткод: | 44201787000 |
| Деталь: | SZ-GP1A73A |
| Парткод: | 4408683480 |
| Деталь: | J-54702-1211 |
| Парткод: | 4843309862 |
| Деталь: | SPE047-070-0386 |
| Парткод: | 44201791000 |
| Деталь: | brkt-feed-unit |
| Парткод: | 44201799000 |
| Деталь: | wh-fed-unit-320 |
| Парткод: | 44205271000 |
| Деталь: | plt-erth-fed-1 |
| Парткод: | 44201803000 |
| Деталь: | plt-erth-fed-2 |
| Парткод: | 44201804000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | WASHER-SEP-320 |
| Парткод: | 44201774000 |
| Деталь: | TBID3008MSZN3L |
| Парткод: | 4842041885 |
| Деталь: | PTBR3006MSZN3A |
| Парткод: | 4842040495 |
| Деталь: | 9HSS30/04MSFB |
| Парткод: | 4842011062 |
| Деталь: | cov-spe/arbor |
| Парткод: | 44201773000 |
| Деталь: | SPR-1.0-15.60RF |
| Парткод: | 44201717000 |
| Деталь: | SPR-1.0-15.60RF |
| Парткод: | 44201817000 |
| Деталь: | K-ROLL-SPT |
| Парткод: | 44201776000 |
| Деталь: | SPC055-045-0159 |
| Парткод: | 44201815000 |
| Деталь: | K-FRM-FUSER-320 |
| Парткод: | 44202968000 |
| Деталь: | HLD-COIL-F |
| Парткод: | 44203176000 |
| Деталь: | BRKT-HLD-COIL-R |
| Парткод: | 44203177000 |
| Деталь: | GEAR-FUS-IN |
| Парткод: | 44203015000 |
| Деталь: | GEAR-FUS-IDL-29 |
| Парткод: | 44203035000 |
| Деталь: | K-ARM-FUS-F |
| Парткод: | 44202903000 |
| Деталь: | K-ARM-FUS-R |
| Парткод: | 44202904000 |
| Деталь: | SPE-ARM-FUS |
| Парткод: | 44202914000 |
| Деталь: | THRM-CS-7TA-190 |
| Парткод: | 44205189000 |
| Деталь: | THMS-HTR-320 |
| Парткод: | 44205182000 |
| Деталь: | WH-HTR-THRM-320 |
| Парткод: | 44205279000 |
| Деталь: | GEAR-SEP-IDLE-1 |
| Парткод: | 44203023000 |
| Деталь: | GEAR-IDLE-15-23 |
| Парткод: | 44203038000 |
| Деталь: | GEAR-IDLE-18-25 |
| Парткод: | 44203036000 |
| Деталь: | LEVER-FUS-ARM-B |
| Парткод: | 44203167000 |
| Деталь: | LEVER-FUS-ARM-H |
| Парткод: | 44203166000 |
| Деталь: | SHAFT-FUS-ARM |
| Парткод: | 44203168000 |
| Деталь: | SPL-FUS-F |
| Парткод: | 44203170000 |
| Деталь: | SPL-FUS-R |
| Парткод: | 44203171000 |
| Деталь: | BRUSH-SUS-HR |
| Парткод: | 44203172000 |
| Деталь: | K-HLD-THERMO |
| Парткод: | 44202992000 |
| Деталь: | HLDER-FUS-REP |
| Парткод: | 44203184000 |
| Деталь: | SCREW-FUS-REP |
| Парткод: | 44203185000 |
| Деталь: | PUSH-NUT-3 |
| Парткод: | 4407408370 |
| Деталь: | SPC-074-040-180 |
| Парткод: | 44203169000 |
| Деталь: | BRKT-FUS-TRM |
| Парткод: | 44203156000 |
| Деталь: | ERR050SKZN3A |
| Парткод: | 4842090312 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | ERR070SKZN3A |
| Парткод: | 4842090314 |
| Деталь: | TPAN3006MSZN3L |
| Парткод: | 4842040665 |
| Деталь: | ZPAN3006MSZN3A |
| Парткод: | 4842080197 |
| Деталь: | BID3006MSCR1AI |
| Парткод: | 7043300613 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | ZPAN3010MSZN3A |
| Парткод: | 4842080199 |
| Деталь: | CLP/W-PLWS1-46B |
| Парткод: | 4843391535 |
| Деталь: | ZPAN3008MSZN3C |
| Парткод: | 4842080198 |
| Деталь: | CLP/W-UAMS05L46 |
| Парткод: | 4843391499 |
| Деталь: | K-FRM-FUSER-320 |
| Парткод: | 44203154000 |
| Деталь: | K-FRM-FUSER-320 |
| Парткод: | 44203053000 |
| Деталь: | THMS-HTR-320 |
| Парткод: | 44205192000 |
| Деталь: | LEVER-FUS-ARM-B |
| Парткод: | 44203178000 |
| Деталь: | SHAFT-FUS-ARM |
| Парткод: | 44203179000 |
| Деталь: | BRKT-FUS-TRM |
| Парткод: | 44203063000 |
| Деталь: | COVER-HINGE-RL |
| Парткод: | 44200464000 |
| Деталь: | COVER-LEFT-R |
| Парткод: | 44200473000 |
| Деталь: | COVER-PANEL-L |
| Парткод: | 44200476000 |
| Деталь: | COVER-REAR-L |
| Парткод: | 44200488000 |
| Деталь: | COVER-REAR-U |
| Парткод: | 44200483000 |
| Деталь: | COVER-RIGHT-RL |
| Парткод: | 44200461000 |
| Деталь: | COVER-RIGHT-RU |
| Парткод: | 44200460000 |
| Деталь: | COVER-TOP-C |
| Парткод: | 44200434000 |
| Деталь: | Cover-Top-L |
| Парткод: | 44200432000 |
| Деталь: | COVER-TRAY-BACK |
| Парткод: | 44200450000 |
| Деталь: | COVER-DF-CONECT |
| Парткод: | 44200485000 |
| Деталь: | TBIDS-4008-CP |
| Парткод: | 4842041794 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | LABEL-FCC |
| Парткод: | 4400740530 |
| Деталь: | LABEL-CHINA |
| Парткод: | 4400685400 |
| Деталь: | LBL-C-TICK-MARK |
| Парткод: | 4402860770 |
| Деталь: | BOOK-HOLDER |
| Парткод: | 44200581000 |
| Деталь: | LBL-LASER |
| Парткод: | 44204534000 |
| Деталь: | LBL-SERVICE-45 |
| Парткод: | 44204604000 |
| Деталь: | LABEL-CANADA-A |
| Парткод: | 4408860880 |
| Деталь: | FOOT-MAIN-AT |
| Парткод: | 41306501000 |
| Деталь: | STUD-FEED-LEFT |
| Парткод: | 44201141000 |
| Деталь: | J-55533-1211 |
| Парткод: | 4843309863 |
| Деталь: | SP-CS1A-B2CA |
| Парткод: | 4843232255 |
| Деталь: | brkt-hold-dump |
| Парткод: | 44201140000 |
| Деталь: | CLP/W-LWS-2U |
| Парткод: | 4843390855 |
| Деталь: | CLP/W-LWS-3U |
| Парткод: | 4843390856 |
| Деталь: | PWZ-SPLSN-22U |
| Парткод: | 4843391582 |
| Деталь: | PWZ-SPSN-22U |
| Парткод: | 4843391594 |
| Деталь: | CLP/W-FLC-10S |
| Парткод: | 4843391674 |
| Деталь: | plate-drv-try |
| Парткод: | 44201852000 |
| Деталь: | BD/W-EDS-1 |
| Парткод: | 4843390941 |
| Деталь: | case-drv-try-f |
| Парткод: | 44201850000 |
| Деталь: | case-drv-try-r |
| Парткод: | 44201851000 |
| Деталь: | CPG-LIFT-28 |
| Парткод: | 41306022000 |
| Деталь: | SPC172-100-3400 |
| Парткод: | 4401966050 |
| Деталь: | GER-TRAY-21 |
| Парткод: | 41306025000 |
| Деталь: | GER-TRAY-24-14 |
| Парткод: | 41306024000 |
| Деталь: | G06S-13/G05S-80 |
| Парткод: | 44201853000 |
| Деталь: | G05H-45/G05S-15 |
| Парткод: | 44201854000 |
| Деталь: | K-M/DC-TRAY-210 |
| Парткод: | 4401981710 |
| Деталь: | foot-rail-left |
| Парткод: | 44201167000 |
| Деталь: | brkt-joint-pfp |
| Парткод: | 44201170000 |
| Деталь: | stay-cst-middle |
| Парткод: | 44201188000 |
| Деталь: | brkt-rear-low |
| Парткод: | 44201143000 |
| Деталь: | stay-rear-low |
| Парткод: | 44201144000 |
| Деталь: | brkt-earth-rear |
| Парткод: | 44201145000 |
| Деталь: | PS-HVT-320 |
| Парткод: | 44205153000 |
| Деталь: | CLP/W-LWS-1U |
| Парткод: | 4843390854 |
| Деталь: | PWZ-KGTS-22K |
| Парткод: | 4843391173 |
| Деталь: | TBID4008MSZN3L |
| Парткод: | 4842040748 |
| Деталь: | BID3006MSCR1AI |
| Парткод: | 4842041899 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | PTBR4008MSZN3A |
| Парткод: | 4842040849 |
| Деталь: | TPAN4008MSZN3L |
| Парткод: | 4842040060 |
| Деталь: | TBIDS-4008-CP |
| Парткод: | 4842041794 |
| Деталь: | THPAN4008MSZN3L |
| Парткод: | 4842040118 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | K-BASE-PWA |
| Парткод: | 44201054000 |
| Деталь: | FRAME-CASE-P-R |
| Парткод: | 44201051000 |
| Деталь: | FRAME-CASE-P-L |
| Парткод: | 44201052000 |
| Деталь: | COV-CASE-PWA-M |
| Парткод: | 44201072000 |
| Деталь: | COV-CASE-PWA-IF |
| Парткод: | 44201074000 |
| Деталь: | COV-FAX-MODULE |
| Парткод: | 44201076000 |
| Деталь: | COV-FAX-D/L |
| Парткод: | 44201077000 |
| Деталь: | COV-PRT-CONNECT |
| Парткод: | 44201078000 |
| Деталь: | WH-SYS-MMF-320 |
| Парткод: | 44205307000 |
| Деталь: | PWZ-SPSN-4U |
| Парткод: | 4843391584 |
| Деталь: | PWZ-SPSN-18U |
| Парткод: | 4843391592 |
| Деталь: | PWZ-SPLSN-18U |
| Парткод: | 4843391580 |
| Деталь: | BD/W-EDS-2323U |
| Парткод: | 4843391240 |
| Деталь: | BD/W-EDS-1 |
| Парткод: | 4843390941 |
| Деталь: | MZ-HDD-320-WD |
| Парткод: | 44205179000 |
| Деталь: | BRKT-HDD-320 |
| Парткод: | 44201085000 |
| Деталь: | SCREW-6-321/4 |
| Парткод: | 44201086000 |
| Деталь: | PWA-F-SYS-320 |
| Парткод: | 44205021000 |
| Деталь: | WIRE/B-EDS-25L |
| Парткод: | 4843391665 |
| Деталь: | HOLD-RHU |
| Парткод: | 44201069000 |
| Деталь: | SNR-HMS-320 |
| Парткод: | 44205186000 |
| Деталь: | WH-LGC-HMS-320 |
| Парткод: | 44205342000 |
| Деталь: | PWZ-SPSN-20U |
| Парткод: | 4843391953 |
| Деталь: | FAN-DC-320 |
| Парткод: | 44205160000 |
| Деталь: | BRKT-FAN-POL |
| Парткод: | 44202301000 |
| Деталь: | PWZ-SPLSN-4U |
| Парткод: | 4843391572 |
| Деталь: | BD/W-EDS-1717U |
| Парткод: | 4843391164 |
| Деталь: | WH-PWR-SYS-320 |
| Парткод: | 44205349000 |
| Деталь: | SHEET-LGC-PWA |
| Парткод: | 44201110000 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | JA-JFS-4S-C1N |
| Парткод: | 4843308931 |
| Деталь: | TPAN4008MSZN3L |
| Парткод: | 4842040060 |
| Деталь: | TPAN4032MSZN3L |
| Парткод: | 4842040059 |
| Деталь: | PWA-F-LGC-320 |
| Парткод: | 44205025000 |
| Деталь: | PWA-F-LGC-321 |
| Парткод: | 44205027000 |
| Деталь: | PWA-F-LGC-322 |
| Парткод: | 44216460000 |
| Деталь: | K-SRAM-T320MU |
| Парткод: | 44205502000 |
| Деталь: | K-SRAM-T320ME |
| Парткод: | 44205503000 |
| Деталь: | K-SRAM-T321MU |
| Парткод: | 44205504000 |
| Деталь: | K-SRAM-T321ME |
| Парткод: | 44205505000 |
| Деталь: | K-SRAM-T322MU |
| Парткод: | 44216421000 |
| Деталь: | K-SRAM-T322ME |
| Парткод: | 44216422000 |
| Деталь: | K-SRAM-T320SU |
| Парткод: | 44205651000 |
| Деталь: | K-SRAM-T320SX |
| Парткод: | 44205653000 |
| Деталь: | K-SRAM-T320SE |
| Парткод: | 44205652000 |
| Деталь: | WH-SYS-HDD-320U |
| Парткод: | 44205353000 |
| Деталь: | WH-SYS-HDD-320 |
| Парткод: | 44205352000 |
| Деталь: | MZ-HDD-320-WD |
| Парткод: | 44205190000 |
| Деталь: | PWA-F-SYS-320 |
| Парткод: | 44205031000 |
| Деталь: | WH-PWR-HDD-320 |
| Парткод: | 44205354000 |
| Деталь: | HOLD-RHU |
| Парткод: | 44201180000 |
| Деталь: | ASM-CH-M-320 |
| Парткод: | 44203500000 |
| Деталь: | MYLAR-M-CH |
| Парткод: | 44203518000 |
| Деталь: | PAD-CLN-300 |
| Парткод: | 4406330470 |
| Деталь: | SFT-WIRE-CLN |
| Парткод: | 44203515000 |
| Деталь: | PUSH-CH-M-F-220 |
| Парткод: | 4408672550 |
| Деталь: | TERMINAL-CH-M-F |
| Парткод: | 44203502000 |
| Деталь: | SPC060-010-0227 |
| Парткод: | 4408672530 |
| Деталь: | HOOK-R-CH-M |
| Парткод: | 44203517000 |
| Деталь: | TERMINAL-CH-M-R |
| Парткод: | 44203505000 |
| Деталь: | WIRE-CH-363 |
| Парткод: | 4408672510 |
| Деталь: | SP-TENSION-CH |
| Парткод: | 4407402190 |
| Деталь: | HANGER-WIRE |
| Парткод: | 4407682120 |
| Деталь: | LID-TERM-F |
| Парткод: | 44203510000 |
| Деталь: | LID-TERM-R |
| Парткод: | 44203512000 |
| Деталь: | GRID-220 |
| Парткод: | 4408672480 |
| Деталь: | CASE-CH-M-320 |
| Парткод: | 44203507000 |
| Деталь: | SPL-CH-M |
| Парткод: | 44203519000 |
| Деталь: | BRKT-CH-UP |
| Парткод: | 44203520000 |
| Деталь: | BRKT-CH-DOWN |
| Парткод: | 44203521000 |
| Деталь: | LBL-WIRE-CLN |
| Парткод: | 44203525000 |
| Деталь: | PTBR3006MSZN3A |
| Парткод: | 4842040495 |
| Деталь: | PAN3004MSZN3A |
| Парткод: | 7040300411 |
| Деталь: | SFT-WIRE-CLN |
| Парткод: | 44203514000 |
| Деталь: | TERMINAL-CH-M-F |
| Парткод: | 44203503000 |
| Деталь: | COVER-EXIT |
| Парткод: | 44202971000 |
| Деталь: | ASM-ROLL-EXIT-U |
| Парткод: | 44203190000 |
| Деталь: | ROLL-EXIT-L-320 |
| Парткод: | 44202973000 |
| Деталь: | sft-exit-l |
| Парткод: | 44202977000 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | gear-exit-u |
| Парткод: | 44202975000 |
| Деталь: | holder-rol-exit |
| Парткод: | 44203026000 |
| Деталь: | gear-mot-ext-id |
| Парткод: | 44203022000 |
| Деталь: | spe-hld-rol-ext |
| Парткод: | 44203028000 |
| Деталь: | scraper-h/r |
| Парткод: | 44202983000 |
| Деталь: | spe-scraper-h/r |
| Парткод: | 44202981000 |
| Деталь: | spl-gnd-exit |
| Парткод: | 44202982000 |
| Деталь: | guide-exit-rtn |
| Парткод: | 44202942000 |
| Деталь: | gate-fuser |
| Парткод: | 44202991000 |
| Деталь: | SHAFT-GATE |
| Парткод: | 44202994000 |
| Деталь: | act-sen-exit |
| Парткод: | 44202997000 |
| Деталь: | spring-act |
| Парткод: | 44202998000 |
| Деталь: | SZ-GP1A73A |
| Парткод: | 4408683480 |
| Деталь: | guide-exit-cov |
| Парткод: | 44202946000 |
| Деталь: | guide-ent-fus |
| Парткод: | 44202927000 |
| Деталь: | SCREW-M3-TENS |
| Парткод: | 4402088600 |
| Деталь: | spl-cov-fuser |
| Парткод: | 44203061000 |
| Деталь: | plate-cov-fuser |
| Парткод: | 44203009000 |
| Деталь: | cover-h/r-r |
| Парткод: | 44202999000 |
| Деталь: | cover-fuser-u |
| Парткод: | 44203001000 |
| Деталь: | cover-fuser-sub |
| Парткод: | 44203007000 |
| Деталь: | LBL-JAM-2 |
| Парткод: | 44204542000 |
| Деталь: | LBL-HOT-COV |
| Парткод: | 44204536000 |
| Деталь: | LBL-FUS-2 |
| Парткод: | 44203098000 |
| Деталь: | lbl-inst-fus |
| Парткод: | 44203097000 |
| Деталь: | ERR050SKZN3A |
| Парткод: | 4842090312 |
| Деталь: | ERR030SKZN3A |
| Парткод: | 4842090310 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 4402203820 |
| Деталь: | 12ZPAN3008MSZ3A |
| Парткод: | 4842040148 |
| Деталь: | spring-exit-f |
| Парткод: | 44203080000 |
| Деталь: | spring-exit-r |
| Парткод: | 44203081000 |
| Деталь: | SZ-LG248L1 |
| Парткод: | 4401983230 |
| Деталь: | eraser-brush |
| Парткод: | 44203029000 |
| Деталь: | plate-exit |
| Парткод: | 44203052000 |
| Деталь: | lbl-fus-3 |
| Парткод: | 44203099000 |
| Деталь: | ZPAN3008MSZN3C |
| Парткод: | 4842080198 |
| Деталь: | ZPAN3010MSZN3A |
| Парткод: | 4842080199 |
| Деталь: | ASM-COIL-IH-100 |
| Парткод: | 44203083000 |
| Деталь: | ASM-COIL-IH-200 |
| Парткод: | 44203084000 |
| Деталь: | ASM-CLEANER-320 |
| Парткод: | 44203400000 |
| Деталь: | K-CASE-AUG-CLN |
| Парткод: | 44203449000 |
| Деталь: | BRKT-BLADE |
| Парткод: | 44203418000 |
| Деталь: | BL-3500D |
| Парткод: | 44299018000 |
| Деталь: | SPE-BLADE-320 |
| Парткод: | 44203422000 |
| Деталь: | K-AUGER-CLN-320 |
| Парткод: | 44203427000 |
| Деталь: | GEAR-AUGER |
| Парткод: | 44203428000 |
| Деталь: | NOZZLE-CLN-320 |
| Парткод: | 44203430000 |
| Деталь: | SEAL-COVER-NZL |
| Парткод: | 44203432000 |
| Деталь: | COVER-NZL-320 |
| Парткод: | 44203437000 |
| Деталь: | SPC-NOZZLE |
| Парткод: | 44203434000 |
| Деталь: | SPD-SCRPR-DRUM |
| Парткод: | 41305536000 |
| Деталь: | SCRAPER-DRUM |
| Парткод: | 41306133000 |
| Деталь: | MYLAR-BLADE-BK |
| Парткод: | 44203414000 |
| Деталь: | SEAL-CLN-F |
| Парткод: | 44203410000 |
| Деталь: | SEAL-CLN-R |
| Парткод: | 44203412000 |
| Деталь: | K-BLADE-REC |
| Парткод: | 44203416000 |
| Деталь: | SEAL-CLN-F2 |
| Парткод: | 44203423000 |
| Деталь: | SEAL-CLN-R2 |
| Парткод: | 44203425000 |
| Деталь: | WASHER-CLN-AUG |
| Парткод: | 44203435000 |
| Деталь: | SEAL-NZL-320 |
| Парткод: | 44203431000 |
| Деталь: | SPC080-055-0120 |
| Парткод: | 44203433000 |
| Деталь: | KNOB-CLN-AUG |
| Парткод: | 44203436000 |
| Деталь: | ROOF-CLN-TOP |
| Парткод: | 44203454000 |
| Деталь: | K-RAIL-CLN-LOW |
| Парткод: | 44203456000 |
| Деталь: | MYL-NZL |
| Парткод: | 44203438000 |
| Деталь: | K-CASE-CLN-320 |
| Парткод: | 44203405000 |
| Деталь: | RAIL-CLN-A |
| Парткод: | 44203743000 |
| Деталь: | GUIDE-CLN-RGST |
| Парткод: | 44203745000 |
| Деталь: | OD-3500 |
| Парткод: | 44299006000 |
| Деталь: | K-SFT-DRUM-320 |
| Парткод: | 44203474000 |
| Деталь: | LP-ERASE-320 |
| Парткод: | 44203765000 |
| Деталь: | RAIL-CLN-B |
| Парткод: | 44203763000 |
| Деталь: | HOLDER-LED-320 |
| Парткод: | 44203720000 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | BUSHING-6 |
| Парткод: | 4407543330 |
| Деталь: | SCREW-COV-IN |
| Парткод: | 4406305940 |
| Деталь: | PTBR3006MSZN3A |
| Парткод: | 4842040495 |
| Деталь: | TPAN4008MSZN3L |
| Парткод: | 4842040060 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | WHEEL-CLN-320 |
| Парткод: | 44203459000 |
| Деталь: | BID3004MSCR1AI |
| Парткод: | 4842041897 |
| Деталь: | ERR050SKZN3A |
| Парткод: | 4842090312 |
| Деталь: | ERR040SKZN3A |
| Парткод: | 4842090311 |
| Деталь: | ERR030SKZN3A |
| Парткод: | 4842090310 |
| Деталь: | COVER-F-PANEL |
| Парткод: | 44200417000 |
| Деталь: | BRKT-PUSH-DOOR |
| Парткод: | 44200422000 |
| Деталь: | MG-CATCH-44 |
| Парткод: | 44200424000 |
| Деталь: | TRAY-PAPER |
| Парткод: | 44200447000 |
| Деталь: | STOP-PAPER |
| Парткод: | 41306169000 |
| Деталь: | PIN-HINGE |
| Парткод: | 4401970110 |
| Деталь: | Cover-Top-R |
| Парткод: | 44200430000 |
| Деталь: | COVER-TOP-FU |
| Парткод: | 44200440000 |
| Деталь: | COVER-TOP-FL |
| Парткод: | 44200442000 |
| Деталь: | COVER-FRM-F-1 |
| Парткод: | 44200453000 |
| Деталь: | COVER-RIGHT-FL |
| Парткод: | 44200457000 |
| Деталь: | COVER-LEFT |
| Парткод: | 44200470000 |
| Деталь: | LBL-TNR-INST |
| Парткод: | 44204526000 |
| Деталь: | LBL/O-RGST |
| Парткод: | 44200452000 |
| Деталь: | F-COV-FRONT45 |
| Парткод: | 44200544000 |
| Деталь: | F-COV-FRONT458 |
| Парткод: | 44200546000 |
| Деталь: | F-COV-FRONT35 |
| Парткод: | 44200545000 |
| Деталь: | F-COV-FRONT358 |
| Парткод: | 44200547000 |
| Деталь: | F-COV-FRONT28 |
| Парткод: | 44216350000 |
| Деталь: | F-COV-FRONT288 |
| Парткод: | 44216351000 |
| Деталь: | LID-SCREW |
| Парткод: | 44200503000 |
| Деталь: | LBL-ENERGY-T-PS |
| Парткод: | 4406359320 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | TBIDS-4008-CP |
| Парткод: | 4842041794 |
| Деталь: | LBL-PM-45/35 |
| Парткод: | 44204520000 |
| Деталь: | LBL-TNR-INST |
| Парткод: | 44204527000 |
| Деталь: | LBL-TNR-INST |
| Парткод: | 44204653000 |
| Деталь: | LBL-PM-45/35/28 |
| Парткод: | 44216363000 |
| Деталь: | ASM-CRG2 |
| Парткод: | 44202680000 |
| Деталь: | HLDR-MIR-CRG2-F |
| Парткод: | 44202682000 |
| Деталь: | HLDR-MIR-CRG2-R |
| Парткод: | 44202683000 |
| Деталь: | K-MIRROR-2 |
| Парткод: | 44202700000 |
| Деталь: | K-MIRROR-3 |
| Парткод: | 44202701000 |
| Деталь: | SPL-MIRROR2-F |
| Парткод: | 44202686000 |
| Деталь: | SPL-MIRROR2/3 |
| Парткод: | 44202687000 |
| Деталь: | SCREW-M3-10-NYL |
| Парткод: | 44202710000 |
| Деталь: | K-BKT-PLY-F-C2 |
| Парткод: | 44202688000 |
| Деталь: | K-BKT-PLY-R-C2 |
| Парткод: | 44202690000 |
| Деталь: | FOOT-CRG-3.64 |
| Парткод: | 4408604590 |
| Деталь: | GUIDE-WH-CRG2 |
| Парткод: | 44202692000 |
| Деталь: | BASE-CRG2 |
| Парткод: | 44202681000 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | ZPAN3006MSZN3A |
| Парткод: | 4842080197 |
| Деталь: | K-CST-AT |
| Парткод: | 41304067000 |
| Деталь: | K-SFT-LIFT-TRAY |
| Парткод: | 41304004000 |
| Деталь: | BUSH-SFT-LIFT |
| Парткод: | 41306028000 |
| Деталь: | LVR-LIFT-TRAY |
| Парткод: | 41305014000 |
| Деталь: | CUSH-LVR-LIFT |
| Парткод: | 41306614000 |
| Деталь: | K-TRAY-CST-AT |
| Парткод: | 41304006000 |
| Деталь: | CUSH-TRAY-CST |
| Парткод: | 41306517000 |
| Деталь: | WALL-SIDE-F-AT |
| Парткод: | 41306033000 |
| Деталь: | LVR-ADJUST-WALL |
| Парткод: | 41305015000 |
| Деталь: | LID-LVR-ADJUST |
| Парткод: | 41306030000 |
| Деталь: | PL-ADJUST-WALL |
| Парткод: | 41305012000 |
| Деталь: | PIN-ADJUST-LVR |
| Парткод: | 41304510000 |
| Деталь: | PIN-ADJUST-WALL |
| Парткод: | 41304511000 |
| Деталь: | K-WALL-SIDE-R |
| Парткод: | 41304065000 |
| Деталь: | LVR-LOC-WALL-R |
| Парткод: | 41306261000 |
| Деталь: | LOCK-WALL-R |
| Парткод: | 41306260000 |
| Деталь: | SPL-LOCK-WALL-R |
| Парткод: | 41305546000 |
| Деталь: | WALL-END-AT |
| Парткод: | 41306031000 |
| Деталь: | COV-CST |
| Парткод: | 41306183000 |
| Деталь: | HANDLE-CST |
| Парткод: | 41306184000 |
| Деталь: | K-PL-PINION-TRY |
| Парткод: | 41304005000 |
| Деталь: | SPC-LVR-WALL |
| Парткод: | 41305503000 |
| Деталь: | LBL/O-P-MAX |
| Парткод: | 41306694000 |
| Деталь: | LBL/O-PAPER |
| Парткод: | 41306692000 |
| Деталь: | LBL/O-GUIDE |
| Парткод: | 41306698000 |
| Деталь: | LBL/O-LD |
| Парткод: | 41306696000 |
| Деталь: | SHEET-CST |
| Парткод: | 41306917000 |
| Деталь: | ERR020SKZN3A |
| Парткод: | 4842090308 |
| Деталь: | TBIDP3008MSZN3A |
| Парткод: | 4842042077 |
| Деталь: | ERR070SKZN3A |
| Парткод: | 4842090314 |
| Деталь: | TBID3008MSZN3A |
| Парткод: | 4842040685 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | TZPAN-M308P-3A |
| Парткод: | 4842042073 |
| Деталь: | 2TWAS40SKZN3A |
| Парткод: | 7402204031 |
| Деталь: | TWAS030MSZN3A |
| Парткод: | 4842080090 |
| Деталь: | SHEET-CST |
| Парткод: | 41306705000 |
| Деталь: | SHEET-CST-US |
| Парткод: | 41306706000 |
| Деталь: | k-plate-pinion |
| Парткод: | 41316588000 |
| Деталь: | PWA-F-SFB-220 |
| Парткод: | 4408682090 |
| Деталь: | WH-SFB-SIZE-320 |
| Парткод: | 44205269000 |
| Деталь: | tray-byp-up |
| Парткод: | 41316594000 |
| Деталь: | guide-tray-r |
| Парткод: | 41316592000 |
| Деталь: | rack-bypass |
| Парткод: | 4408669710 |
| Деталь: | guide-tray-f |
| Парткод: | 41316593000 |
| Деталь: | k-rack-bypass |
| Парткод: | 4408669700 |
| Деталь: | pinion-18-395 |
| Парткод: | 4407726480 |
| Деталь: | tray-byp-dw |
| Парткод: | 41316595000 |
| Деталь: | tray-byp-m |
| Парткод: | 41316596000 |
| Деталь: | spg-pt-tray-byp |
| Парткод: | 41316597000 |
| Деталь: | PAD-BRAKE |
| Парткод: | 4400901130 |
| Деталь: | k-sft-tray-byp |
| Парткод: | 41316582000 |
| Деталь: | brkt-tray-byp |
| Парткод: | 41316578000 |
| Деталь: | spg-tray-byp |
| Парткод: | 41316580000 |
| Деталь: | k-try-byp-m-sub |
| Парткод: | 41316634000 |
| Деталь: | lbl-high-tray-t |
| Парткод: | 41316602000 |
| Деталь: | lbl-tray-eu |
| Парткод: | 41316600000 |
| Деталь: | ZPAN3008MSZN3C |
| Парткод: | 4842080198 |
| Деталь: | NUT030MSZN3A |
| Парткод: | 4842090241 |
| Деталь: | TBID3006MSZN3A |
| Парткод: | 4842040683 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | BID3006MSCR1AI |
| Парткод: | 4842041899 |
| Деталь: | ERR070SKZN3A |
| Парткод: | 4842090314 |
| Деталь: | k-plate-pinion |
| Парткод: | 44201978000 |
| Деталь: | k-sft-tray-byp |
| Парткод: | 44201988000 |
| Деталь: | F-COV-CONP |
| Парткод: | 44200701000 |
| Деталь: | COVER-LED-P |
| Парткод: | 44200715000 |
| Деталь: | KEY-C/S |
| Парткод: | 44200721000 |
| Деталь: | KEY-NUMBER |
| Парткод: | 44200725000 |
| Деталь: | KEY-POWER |
| Парткод: | 44200717000 |
| Деталь: | KEY-STATUS |
| Парткод: | 44200723000 |
| Деталь: | KEY-FC |
| Парткод: | 44200719000 |
| Деталь: | KEY-PRINT |
| Парткод: | 44200722000 |
| Деталь: | KEY-HELP |
| Парткод: | 44200724000 |
| Деталь: | KEY-INT |
| Парткод: | 44200720000 |
| Деталь: | BRKT-CONP-C |
| Парткод: | 44200741000 |
| Деталь: | BRKT-CONP-L |
| Парткод: | 44200742000 |
| Деталь: | BRKT-CONP-R |
| Парткод: | 44200740000 |
| Деталь: | PWA-F-DSP-320 |
| Парткод: | 44204999000 |
| Деталь: | PWA-F-KEY-320 |
| Парткод: | 44204952000 |
| Деталь: | MYLAR-SHIELD |
| Парткод: | 44200734000 |
| Деталь: | K-PNL-TOUCH-320 |
| Парткод: | 44200745000 |
| Деталь: | WH-DSP-LCD-300 |
| Парткод: | 4406382420 |
| Деталь: | LCD-TOUCH-154 |
| Парткод: | 4402322450 |
| Деталь: | CFL-LCD-230 |
| Парткод: | 4402956850 |
| Деталь: | SEAL-DISP |
| Парткод: | 4406306730 |
| Деталь: | PTBR3012MSZN3A |
| Парткод: | 4842040848 |
| Деталь: | SCREW-2006 |
| Парткод: | 4406306740 |
| Деталь: | K-COVER-LED-F |
| Парткод: | 44200732000 |
| Деталь: | K-KEY-FUNCTION |
| Парткод: | 44200728000 |
| Деталь: | CASE-GATE-TNR |
| Парткод: | 44204451000 |
| Деталь: | K-BRKT-TNR-DRV |
| Парткод: | 44204470000 |
| Деталь: | SHUTTER-GATE |
| Парткод: | 44204336000 |
| Деталь: | BRKT-GEAR-R |
| Парткод: | 44204476000 |
| Деталь: | AUGER-TNR |
| Парткод: | 44204338000 |
| Деталь: | BUSH-061206F-M |
| Парткод: | 44204339000 |
| Деталь: | K-MOT-D/C-TNR |
| Парткод: | 44204340000 |
| Деталь: | GP05S022/2GT044 |
| Парткод: | 44204342000 |
| Деталь: | GG5S032/05S082 |
| Парткод: | 44204343000 |
| Деталь: | GEAR-05S036-06 |
| Парткод: | 44204344000 |
| Деталь: | COV-TNR-DRV-F |
| Парткод: | 44204453000 |
| Деталь: | SPC076-060-0170 |
| Парткод: | 44204346000 |
| Деталь: | SPC054-040-0440 |
| Парткод: | 44204347000 |
| Деталь: | BLT/T-120-2GT-2 |
| Парткод: | 44204349000 |
| Деталь: | GASSKET-TNR-DRV |
| Парткод: | 44204457000 |
| Деталь: | COUPL-GEAR-STOP |
| Парткод: | 44204465000 |
| Деталь: | CLP/W-LWS-4U |
| Парткод: | 4843390857 |
| Деталь: | COUPLING-BTL-U |
| Парткод: | 44204461000 |
| Деталь: | COUPLING-BTL-D |
| Парткод: | 44204463000 |
| Деталь: | COUPLING-BTL-E |
| Парткод: | 44204462000 |
| Деталь: | SEAL-VR55A |
| Парткод: | 44204478000 |
| Деталь: | SEAL-VR14A |
| Парткод: | 44204479000 |
| Деталь: | SM-SSO1GL2T |
| Парткод: | 4407966810 |
| Деталь: | WH-TNR-SW-320 |
| Парткод: | 44205296000 |
| Деталь: | COV-HNS-DEV-F |
| Парткод: | 44204358000 |
| Деталь: | ARM-BOX-SP |
| Парткод: | 44204375000 |
| Деталь: | SPE063-050-0232 |
| Парткод: | 44204390000 |
| Деталь: | GUIDE-BOTLE-IN |
| Парткод: | 44204352000 |
| Деталь: | HANDLE-BOTTLE |
| Парткод: | 44204355000 |
| Деталь: | BUSH-AUGER-TNR |
| Парткод: | 44204458000 |
| Деталь: | GG08S031/COUP |
| Парткод: | 44204467000 |
| Деталь: | GG05S066/08S014 |
| Парткод: | 44204466000 |
| Деталь: | SEAL-WAS-5471 |
| Парткод: | 44204456000 |
| Деталь: | SEAL-WAS-1426 |
| Парткод: | 44204459000 |
| Деталь: | STAY-BOTTLE |
| Парткод: | 44204335000 |
| Деталь: | CLP/W-LWS-8SL25 |
| Парткод: | 4843391707 |
| Деталь: | J-0-175694-2 |
| Парткод: | 4843306485 |
| Деталь: | BRKT-TNR-COV-1 |
| Парткод: | 44204334000 |
| Деталь: | PS-ZT3500 |
| Парткод: | 66089630 |
| Деталь: | PS-ZT3500D |
| Парткод: | 66089632 |
| Деталь: | PS-ZT3500E |
| Парткод: | 66089631 |
| Деталь: | CLP/W-UAMS-05-2 |
| Парткод: | 4843391391 |
| Деталь: | BRKT-SFT-COV |
| Парткод: | 44204333000 |
| Деталь: | GUIDE-TNR-BTL |
| Парткод: | 44204341000 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | TPAN4008MSZN3L |
| Парткод: | 4842040060 |
| Деталь: | PAN2008MSZN3AI |
| Парткод: | 7040200811 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | PTBR3006MSZN3A |
| Парткод: | 4842040495 |
| Деталь: | TBID4008MSZN3L |
| Парткод: | 4842040748 |
| Деталь: | PS-TB3500 |
| Парткод: | 66089633 |
| Деталь: | PS-TB3500E |
| Парткод: | 66089634 |
| Деталь: | SPC086-065-0220 |
| Парткод: | 44204377000 |
| Деталь: | BRKT-MS-BTL |
| Парткод: | 44204308000 |
| Деталь: | STAY-BOTTLE |
| Парткод: | 44204392000 |
| Деталь: | GUIDE-TNR-BTL |
| Парткод: | 44204393000 |
| Деталь: | PAN3003MSZN3AI |
| Парткод: | 7040300311 |
| Деталь: | SCREW20D23 |
| Парткод: | 44204394000 |
| Деталь: | FRAME-B-ADU-320 |
| Парткод: | 44203230000 |
| Деталь: | K-FRM-R-ADU |
| Парткод: | 41316021000 |
| Деталь: | GUIDE-PAPER-U |
| Парткод: | 44203261000 |
| Деталь: | GUIDE-PAPER-L32 |
| Парткод: | 44203252000 |
| Деталь: | SCREW-CASET |
| Парткод: | 4400662390 |
| Деталь: | ROLL-TRANS-C |
| Парткод: | 41316029000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | U_ VO 1 O CM 0 VO CM 1 1 - - _1 Cl. |
| Парткод: | 41317050000 |
| Деталь: | NPIN2-8 |
| Парткод: | 4407403790 |
| Деталь: | BLT/T-282-2GT-5 |
| Парткод: | 41316033000 |
| Деталь: | ROLL-TRANS-L-32 |
| Парткод: | 44203222000 |
| Деталь: | ASM-CLT-G28-CW6 |
| Парткод: | 4401969920 |
| Деталь: | K-BKT-MOT-ADU |
| Парткод: | 44203212000 |
| Деталь: | K-MOT-EXIT-320 |
| Парткод: | 44205169000 |
| Деталь: | GP08S024/2GT020 |
| Парткод: | 44203218000 |
| Деталь: | GG08S024/10S028 |
| Парткод: | 44203219000 |
| Деталь: | GEAR-08S024 |
| Парткод: | 44203220000 |
| Деталь: | BLT/T-426-2GT-5 |
| Парткод: | 44203250000 |
| Деталь: | LEVER-LATCH-F |
| Парткод: | 41316055000 |
| Деталь: | LEVER-LATCH-R32 |
| Парткод: | 44203255000 |
| Деталь: | SHAFT-OPEN-320 |
| Парткод: | 44203253000 |
| Деталь: | SPE-068-070-241 |
| Парткод: | 41316064000 |
| Деталь: | GROMET-EHP-6U |
| Парткод: | 4842416026 |
| Деталь: | PWZ-KGLS-24RTVO |
| Парткод: | 4843391721 |
| Деталь: | PWA-F-ADU-320 |
| Парткод: | 44204943000 |
| Деталь: | SZ-FED-210 |
| Парткод: | 4401983080 |
| Деталь: | WH-ADU-CVSW |
| Парткод: | 41316251000 |
| Деталь: | WH-ADU-FED-L |
| Парткод: | 41316252000 |
| Деталь: | WH-ADU-320 |
| Парткод: | 44205267000 |
| Деталь: | WH-ADU-FED-U |
| Парткод: | 41316254000 |
| Деталь: | BRKT-WIRE |
| Парткод: | 41316070000 |
| Деталь: | BD/W-EDS-2323U |
| Парткод: | 4843391240 |
| Деталь: | SPL-ADU-320 |
| Парткод: | 44203240000 |
| Деталь: | BD/W-SG-130 |
| Парткод: | 4843390903 |
| Деталь: | CASE-ADU |
| Парткод: | 44203260000 |
| Деталь: | SP-CS3A-B2BA |
| Парткод: | 4402859600 |
| Деталь: | COVER-IN-R-320 |
| Парткод: | 44203254000 |
| Деталь: | GUIDE-PAPER-IN |
| Парткод: | 44203242000 |
| Деталь: | ROLL-TRANS-IDLE |
| Парткод: | 41316101000 |
| Деталь: | SPR-IDLE |
| Парткод: | 41316103000 |
| Деталь: | SPL-GUIDE-IN |
| Парткод: | 41316102000 |
| Деталь: | LBL-PLACE-COV |
| Парткод: | 44204558000 |
| Деталь: | TBID3006MSZN3A |
| Парткод: | 4842040683 |
| Деталь: | SCREW-MR-M3-6 |
| Парткод: | 4842041799 |
| Деталь: | 9HSS30/03MSFB |
| Парткод: | 4842011061 |
| Деталь: | ERR050SKZN3A |
| Парткод: | 4842090312 |
| Деталь: | ZPAN3008MSZN3C |
| Парткод: | 4842080198 |
| Деталь: | TBID3008MSCR3C |
| Парткод: | 4842040686 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | K-FRAME-R-ADU |
| Парткод: | 41316017000 |
| Деталь: | K-FRM-R-ADU-320 |
| Парткод: | 44203280000 |
| Деталь: | FRAME-F-ADU |
| Парткод: | 44203270000 |
| Деталь: | BRKT-MOT-U |
| Парткод: | 41316042000 |
| Деталь: | LEVER-LATCH-F |
| Парткод: | 41316054000 |
| Деталь: | LEVER-OPEN |
| Парткод: | 41316058200 |
| Деталь: | WIRE/B-SKB-1M |
| Парткод: | 4843391656 |
| Деталь: | COVER-INSIDE-F |
| Парткод: | 44203265000 |
| Деталь: | COVER-INSIDE-F |
| Парткод: | 44203271000 |
| Деталь: | COVER-IN-R-320 |
| Парткод: | 44203272000 |
| Деталь: | base-lens |
| Парткод: | 44202790000 |
| Деталь: | cover-sec |
| Парткод: | 44202793000 |
| Деталь: | GLASS-ADF |
| Парткод: | 44202865000 |
| Деталь: | PWA-F-SLG-320 |
| Парткод: | 44205013000 |
| Деталь: | PWZ-SPS-3U |
| Парткод: | 4843390858 |
| Деталь: | WH-SLG-SPLY-320 |
| Парткод: | 44205319000 |
| Деталь: | SNSR-PS-TY1CH56 |
| Парткод: | 4406379920 |
| Деталь: | spl-glas-adf |
| Парткод: | 44202867000 |
| Деталь: | k-stay-glass-f |
| Парткод: | 44202800000 |
| Деталь: | k-stay-glass-r |
| Парткод: | 44202820000 |
| Деталь: | SZ-GP1A73A |
| Парткод: | 4408683480 |
| Деталь: | clp-wire-press |
| Парткод: | 4406319330 |
| Деталь: | wh-slg-rear-320 |
| Парткод: | 44205318000 |
| Деталь: | PWB-F-CBL-320 |
| Парткод: | 44204942000 |
| Деталь: | spl-sheild-scan |
| Парткод: | 44202557000 |
| Деталь: | GSKT-3-10-23 |
| Парткод: | 44202553000 |
| Деталь: | cover-f-cbl |
| Парткод: | 44202554000 |
| Деталь: | spl-shield-cov |
| Парткод: | 44202776000 |
| Деталь: | spl-shield-ccd |
| Парткод: | 44202552000 |
| Деталь: | CLP/W-RLWS-3TV0 |
| Парткод: | 4843391670 |
| Деталь: | CLP/W-LWS-05 |
| Парткод: | 4843391562 |
| Деталь: | CLP/W-E0803A |
| Парткод: | 44202555000 |
| Деталь: | CLP/W-ENT-7N |
| Парткод: | 44202556000 |
| Деталь: | SHEET-CRG1 |
| Парткод: | 44202563000 |
| Деталь: | SHEET-CRG2 |
| Парткод: | 44202564000 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | Z-MA-TB-2533 |
| Парткод: | 4843390083 |
| Деталь: | ZPAN3008MSZN3A |
| Парткод: | 7640300851 |
| Деталь: | TPAN3006MSZN3L |
| Парткод: | 4842040665 |
| Деталь: | PAN3004MSZN3A |
| Парткод: | 7040300411 |
| Деталь: | SCREW-M4-7-R |
| Парткод: | 4842041800 |
| Деталь: | SNSR-PS-TW05 |
| Парткод: | 44205167000 |
| Деталь: | WH-SLG-APS-320L |
| Парткод: | 44205311000 |
| Деталь: | wh-slg-aps-320A |
| Парткод: | 44205305000 |
| Деталь: | WH-SYS-SLG-320U |
| Парткод: | 44205350000 |
| Деталь: | WH-SYS-SLG-320 |
| Парткод: | 44205339000 |
| Деталь: | ADJ-ASM-LENS320 |
| Парткод: | 44204772000 |
| Деталь: | k-cover-lens |
| Парткод: | 44202775000 |
| Деталь: | SCREW-MR-M3-6 |
| Парткод: | 4842041779 |
| Деталь: | k-shield-scan |
| Парткод: | 44202545000 |
| Деталь: | CLP/W-EMT-5N |
| Парткод: | 4402953750 |
| Деталь: | asm-d/h-scn-l-u |
| Парткод: | 44202501000 |
| Деталь: | asm-d/h-scn-l-e |
| Парткод: | 44202502000 |
| Деталь: | asm-d/h-scn-r-u |
| Парткод: | 44202504000 |
| Деталь: | asm-d/h-scn-r-e |
| Парткод: | 44202505000 |
| Деталь: | HOLDER-PWA-IH |
| Парткод: | 44203040000 |
| Деталь: | WH-HTR-THMS-320 |
| Парткод: | 44205329000 |
| Деталь: | WH-IH-ACIN-320 |
| Парткод: | 44205334000 |
| Деталь: | PLT-TERMINAL-1 |
| Парткод: | 44203042000 |
| Деталь: | PLT-TERMINAL-2 |
| Парткод: | 44203043000 |
| Деталь: | K-STAY-FUS |
| Парткод: | 44203010000 |
| Деталь: | SEAL-DUCT-IH |
| Парткод: | 44203060000 |
| Деталь: | SCREW-LINK-M4 |
| Парткод: | 44200880000 |
| Деталь: | PS-IH-320U |
| Парткод: | 44205157100 |
| Деталь: | PS-IH-320E |
| Парткод: | 44205157200 |
| Деталь: | PS-IH-320S |
| Парткод: | 44205157300 |
| Деталь: | PAN4006MSZN3AI |
| Парткод: | 7040400611 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | TPAN4008MSZN3L |
| Парткод: | 4842040060 |
| Деталь: | K-STAY-FUS |
| Парткод: | 44203089000 |
| Деталь: | GLASS-PLATEN |
| Парткод: | 44202866000 |
| Деталь: | K-GUIDE-GLASS |
| Парткод: | 44202861000 |
| Деталь: | seal-glass |
| Парткод: | 44202869000 |
| Деталь: | Guide-Rear |
| Парткод: | 44202864000 |
| Деталь: | tape-gls-platen |
| Парткод: | 44202871000 |
| Деталь: | lbl-scale-x-l |
| Парткод: | 44202852000 |
| Деталь: | lbl-scale-x-a |
| Парткод: | 44202851000 |
| Деталь: | lbl-scale-x-k |
| Парткод: | 44202855000 |
| Деталь: | lbl-scale-y-l |
| Парткод: | 44202854000 |
| Деталь: | lbl-scale-y-a |
| Парткод: | 44202853000 |
| Деталь: | lbl-scale-y-k |
| Парткод: | 44202856000 |
| Деталь: | PLATEN |
| Парткод: | 41306189000 |
| Деталь: | pocket-platen |
| Парткод: | 41306190000 |
| Деталь: | sheet-platen |
| Парткод: | 41306586000 |
| Деталь: | hinge-platen-at |
| Парткод: | 41306667000 |
| Деталь: | TBIDP4014MSZN3A |
| Парткод: | 4842042069 |
| Деталь: | BRKT-BRIDGE |
| Парткод: | 44200875000 |
| Деталь: | COV-POWER-FIN |
| Парткод: | 44201034000 |
| Деталь: | BD/W-EDS-1 |
| Парткод: | 4843390941 |
| Деталь: | CLP/W-LWS-3U |
| Парткод: | 4843390856 |
| Деталь: | CLP/W-LWS-2U |
| Парткод: | 4843390855 |
| Деталь: | CLP/W-RLWS-3TV0 |
| Парткод: | 4843391670 |
| Деталь: | K-BRKT-MOT-EXIT |
| Парткод: | 44203018000 |
| Деталь: | K-MOT-EXIT-320 |
| Парткод: | 44205169000 |
| Деталь: | BRKT-POWER |
| Парткод: | 44201030000 |
| Деталь: | INLET-AP300-2A2 |
| Парткод: | 4401981080 |
| Деталь: | WH-LGC-FIN-320 |
| Парткод: | 44205264000 |
| Деталь: | WH-ACMAIN-320 |
| Парткод: | 44205332000 |
| Деталь: | WH-INLET-G-320 |
| Парткод: | 44205289000 |
| Деталь: | WH-INLET-L-320 |
| Парткод: | 44205288000 |
| Деталь: | WH-INLET-N-320 |
| Парткод: | 44205331000 |
| Деталь: | FRAME-REAR-MID |
| Парткод: | 44200947000 |
| Деталь: | BD/W-EDS-2323U |
| Парткод: | 4843391240 |
| Деталь: | GMT-OBC-875 |
| Парткод: | 4842414633 |
| Деталь: | BRKT-TOP-R |
| Парткод: | 44200965000 |
| Деталь: | BD/W-EDS-2 |
| Парткод: | 4843390942 |
| Деталь: | BRKT-FRM-R-SUB |
| Парткод: | 44200970000 |
| Деталь: | STUD-LEV-ADU-R |
| Парткод: | 44203228000 |
| Деталь: | CLP/W-LWS-4U |
| Парткод: | 4843390857 |
| Деталь: | BRKT-REAR-SUB |
| Парткод: | 44201007000 |
| Деталь: | COV-DEV-DUCT |
| Парткод: | 44204266000 |
| Деталь: | FAN-DEV-320 |
| Парткод: | 44205180000 |
| Деталь: | BRKT-DRV-DRUM |
| Парткод: | 44201380000 |
| Деталь: | DUCT-IH |
| Парткод: | 44200869000 |
| Деталь: | SEAL-DEV-DUCT |
| Парткод: | 44204267000 |
| Деталь: | DUCT-DEV-REAR |
| Парткод: | 44204265000 |
| Деталь: | BRKT-KEY-CTR |
| Парткод: | 44200920000 |
| Деталь: | CLP/W-LWS-8SL25 |
| Парткод: | 4843391707 |
| Деталь: | TPAN4008MSZN3L |
| Парткод: | 4842040060 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | BID4006MSCR1AI |
| Парткод: | 4842041904 |
| Деталь: | ZPANE4008BSNI3E |
| Парткод: | 4842041837 |
| Деталь: | TBID3006MSZN3R |
| Парткод: | 4842042103 |
| Деталь: | BD/W-EDS-1717U |
| Парткод: | 4843391164 |
| Деталь: | FL-VU-215F3-M |
| Парткод: | 4402322610 |
| Деталь: | FL-ZSG2215-11 |
| Парткод: | 4402953150 |
| Деталь: | B-NRW10-15A-Y |
| Парткод: | 4402255020 |
| Деталь: | B-NRW10-10A-Y |
| Парткод: | 4402255050 |
| Деталь: | PS-ACC-320-JU |
| Парткод: | 44205152000 |
| Деталь: | PS-ACC-320-E |
| Парткод: | 44205152100 |
| Деталь: | CBL/P-INLET-UC |
| Парткод: | 4402449900 |
| Деталь: | CBL/P-INLET-AU |
| Парткод: | 4400494940 |
| Деталь: | CBL/P-INLET-EUR |
| Парткод: | 4400395940 |
| Деталь: | CBL-INLET-CND |
| Парткод: | 4402494070 |
| Деталь: | BRKT-HTR-PWA |
| Парткод: | 44204725000 |
| Деталь: | PWA-F-FUS-320U |
| Парткод: | 44204975100 |
| Деталь: | PWA-F-FUS-320E |
| Парткод: | 44204975200 |
| Деталь: | PWZ-SPLSN-6U |
| Парткод: | 4843391573 |
| Деталь: | PWZ-SPSN-6U |
| Парткод: | 4843391585 |
| Деталь: | WH-D/H-FUS-320 |
| Парткод: | 44205337000 |
| Деталь: | CLP/W-LWS-5S-2W |
| Парткод: | 4843391394 |
| Деталь: | CLP/W-LWS-3S |
| Парткод: | 4843391392 |
| Деталь: | ZPAN3008MSZN3C |
| Парткод: | 4842080198 |
| Деталь: | STAY-DEV-320 |
| Парткод: | 44204161000 |
| Деталь: | TERM-BIAS-DEV |
| Парткод: | 44204162000 |
| Деталь: | PLT-TERM-BIAS |
| Парткод: | 44204163000 |
| Деталь: | SEAL-STAY-DEV |
| Парткод: | 44204164000 |
| Деталь: | WH-HVT-D-320 |
| Парткод: | 44205286000 |
| Деталь: | PLATE-BIAS-SUB |
| Парткод: | 44204165000 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | TPAN4008MSZN3L |
| Парткод: | 4842040060 |
| Деталь: | ASM-HTR-D-U |
| Парткод: | 44204731000 |
| Деталь: | ASM-HTR-D-E |
| Парткод: | 44204732000 |
| Деталь: | K-COVER-GUIDE |
| Парткод: | 44203140000 |
| Деталь: | FAN-DC-320 |
| Парткод: | 44205160000 |
| Деталь: | RING-STOP-FAN |
| Парткод: | 44203113000 |
| Деталь: | WH-EXIT-FAN-320 |
| Парткод: | 44205287000 |
| Деталь: | PUSHER-DOOR-SW |
| Парткод: | 44203117000 |
| Деталь: | MG-CATCH-44 |
| Парткод: | 44200424000 |
| Деталь: | STOPPER-COV-CLN |
| Парткод: | 44203115000 |
| Деталь: | TERM-TCH-COV |
| Парткод: | 44203902000 |
| Деталь: | PLT-T-TRM-COV |
| Парткод: | 44203905000 |
| Деталь: | PLT-S-TRM-COV |
| Парткод: | 44203906000 |
| Деталь: | SPC-TRM-COV-078 |
| Парткод: | 44203910000 |
| Деталь: | HOLDER-TRS |
| Парткод: | 44203121000 |
| Деталь: | BRKT-GND-TCH-R |
| Парткод: | 44203136000 |
| Деталь: | SPC095-070-0230 |
| Парткод: | 44203129000 |
| Деталь: | GUIDE-COVER-ADU |
| Парткод: | 44203139000 |
| Деталь: | FILTER-OZ-320TK |
| Парткод: | 44203925000 |
| Деталь: | COVER-FILTER |
| Парткод: | 44203125000 |
| Деталь: | LABEL-DRUM-PS |
| Парткод: | 44204544000 |
| Деталь: | SPC093-070-0227 |
| Парткод: | 44203134000 |
| Деталь: | STOPPER-FAN-TRS |
| Парткод: | 44203143000 |
| Деталь: | LBL-JAM-1 |
| Парткод: | 44204540000 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | 12ZPAN3008MSZ3A |
| Парткод: | 4842040148 |
| Деталь: | BRKT-GND-TCH-R |
| Парткод: | 44203146000 |
| Деталь: | FILTER-OZ-32CP7 |
| Парткод: | 44203926000 |
| Деталь: | ASM-CRG1 |
| Парткод: | 44202720000 |
| Деталь: | LP-EXPO-50K-320 |
| Парткод: | 44205150000 |
| Деталь: | INV-EXP-50K-320 |
| Парткод: | 44205151000 |
| Деталь: | COV-INV |
| Парткод: | 44202728000 |
| Деталь: | K-REFLECTOR |
| Парткод: | 44202722000 |
| Деталь: | FOOT-CRG-3.64 |
| Парткод: | 4408604590 |
| Деталь: | SPL-MIRROR1-F |
| Парткод: | 44202725000 |
| Деталь: | SPL-MIRROR1-R |
| Парткод: | 44202726000 |
| Деталь: | SCREW-M3-10-NYL |
| Парткод: | 44202710000 |
| Деталь: | WH-SLG-INV-320 |
| Парткод: | 44205314000 |
| Деталь: | GUIDE-WH-CRG1 |
| Парткод: | 44202727000 |
| Деталь: | GROMET-EHP-6U |
| Парткод: | 4842416026 |
| Деталь: | BASE-CRG1 |
| Парткод: | 44202721000 |
| Деталь: | MYL-WH-SLG-INV |
| Парткод: | 44202731000 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | PTBR3006MSZN3A |
| Парткод: | 4842040495 |
| Деталь: | BID3006MSCR1AI |
| Парткод: | 7043300613 |
| Деталь: | K-REFRECTOR |
| Парткод: | 44202734000 |
| Деталь: | MIRROR-1-320 |
| Парткод: | 44202744000 |
| Деталь: | K-BRKT-DRV-MAIN |
| Парткод: | 44201330000 |
| Деталь: | BRKT-ARM-FEED |
| Парткод: | 44201371000 |
| Деталь: | SHAFT-ARM-FEED |
| Парткод: | 44201370000 |
| Деталь: | GEAR-10S025-06F |
| Парткод: | 44201376000 |
| Деталь: | GEAR-10S047-06 |
| Парткод: | 44201375000 |
| Деталь: | K-BRG-GEAR/S033 |
| Парткод: | 44201347000 |
| Деталь: | GEAR-10S024-06 |
| Парткод: | 44201368000 |
| Деталь: | K-GEAR-050-CUP |
| Парткод: | 44201394000 |
| Деталь: | GEAR-10S023-06 |
| Парткод: | 44201367000 |
| Деталь: | GEAR-10S023-06 |
| Парткод: | 44201362000 |
| Деталь: | GEAR-10S027-06 |
| Парткод: | 44201361000 |
| Деталь: | GG05H072/08H030 |
| Парткод: | 44201350000 |
| Деталь: | K-BRG-GEAR/H064 |
| Парткод: | 44201346000 |
| Деталь: | GG10S025/10S014 |
| Парткод: | 44201353000 |
| Деталь: | GEAR-10S022-06 |
| Парткод: | 44201360000 |
| Деталь: | GG10S021/10S036 |
| Парткод: | 44201379000 |
| Деталь: | GEAR-10S028-DEV |
| Парткод: | 44201365000 |
| Деталь: | GEAR-10H025-DEV |
| Парткод: | 44201366000 |
| Деталь: | BD/W-EDS-2 |
| Парткод: | 4843390942 |
| Деталь: | TERM-HVM-320 |
| Парткод: | 44203705000 |
| Деталь: | PLT-TERM-HVM |
| Парткод: | 44203707000 |
| Деталь: | SPL-TERM-HVM |
| Парткод: | 44203710000 |
| Деталь: | WH-HVT-M-320 |
| Парткод: | 44205285000 |
| Деталь: | HOLDER-RGST-CLT |
| Парткод: | 44201340000 |
| Деталь: | PWZ-SPLSN-3U |
| Парткод: | 4843391571 |
| Деталь: | M/DC-MAIN-320 |
| Парткод: | 44205161000 |
| Деталь: | BRKT-UTNR-FULL |
| Парткод: | 44201342000 |
| Деталь: | SZ-GP1A73A |
| Парткод: | 4408683480 |
| Деталь: | WH-UTNR-320 |
| Парткод: | 44205320000 |
| Деталь: | GEAR-027-CUP |
| Парткод: | 44201391000 |
| Деталь: | ERR050SKZN3A |
| Парткод: | 4842090312 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | TBID3008MSZN3L |
| Парткод: | 4842041885 |
| Деталь: | TPAN4008MSZN3L |
| Парткод: | 4842040060 |
| Деталь: | K-BRKT-DRV-MAIN |
| Парткод: | 44201388000 |
| Деталь: | BRKT-ARM-FEED |
| Парткод: | 44201383000 |
| Деталь: | SHAFT-ARM-FEED |
| Парткод: | 44201385000 |
| Деталь: | DAMPER-DRV-DRUM |
| Парткод: | 44201395000 |
| Деталь: | FRAME-FEEDER-F |
| Парткод: | 44201571000 |
| Деталь: | FOOT-MAIN-AT |
| Парткод: | 41306501000 |
| Деталь: | K-FRM-FEEDER-R |
| Парткод: | 44201580000 |
| Деталь: | RAIL-CST-RIGHT |
| Парткод: | 44201600000 |
| Деталь: | SLIDER-CST |
| Парткод: | 41306007000 |
| Деталь: | ROLLER-FEEDER |
| Парткод: | 44201611000 |
| Деталь: | BUSHING |
| Парткод: | 4346312030 |
| Деталь: | GG10S024/10S030 |
| Парткод: | 44201684000 |
| Деталь: | GG10S031/10S038 |
| Парткод: | 44201681000 |
| Деталь: | GEAR-10S035-06 |
| Парткод: | 44201862000 |
| Деталь: | GEAR-10S034-06 |
| Парткод: | 44201683000 |
| Деталь: | GEAR-10S033-06 |
| Парткод: | 44201686000 |
| Деталь: | K-BKT-DRV-FED-1 |
| Парткод: | 44201721000 |
| Деталь: | BRKT-DRV-FEED-2 |
| Парткод: | 44201690000 |
| Деталь: | ASM-CLT-G28-CW6 |
| Парткод: | 4401969920 |
| Деталь: | SHAFT-ID-CLUCH |
| Парткод: | 44201747000 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | GEAR-10S035-06D |
| Парткод: | 44201700000 |
| Деталь: | ASM-CLT-G28-CW8 |
| Парткод: | 4401969900 |
| Деталь: | GEAR-10S028-06D |
| Парткод: | 44201701000 |
| Деталь: | K-BKT-DRV-FED-3 |
| Парткод: | 44201741000 |
| Деталь: | GG10S040/10S034 |
| Парткод: | 44201730000 |
| Деталь: | GG10S020/10S025 |
| Парткод: | 44201732000 |
| Деталь: | GEAR-10S021-06 |
| Парткод: | 44201733000 |
| Деталь: | GEAR-10S023-06 |
| Парткод: | 44201734000 |
| Деталь: | GG10S025/10S021 |
| Парткод: | 44201680000 |
| Деталь: | CLP/W-LWS-2U |
| Парткод: | 4843390855 |
| Деталь: | GEAR-10S033-06 |
| Парткод: | 44201746000 |
| Деталь: | BD/W-EDS-2 |
| Парткод: | 4843390942 |
| Деталь: | K-BRKT-ADU-F |
| Парткод: | 44201641000 |
| Деталь: | BRKT-HOLD-SFB-F |
| Парткод: | 44201645000 |
| Деталь: | K-BRKT-ADU-R |
| Парткод: | 44201651000 |
| Деталь: | K-BKT-HLD-SFB-R |
| Парткод: | 44201655000 |
| Деталь: | BUSH-ROL-FEEDER |
| Парткод: | 44201613000 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | TBID4008MSZN3L |
| Парткод: | 4842040748 |
| Деталь: | TBID3008MSZN3L |
| Парткод: | 4842041885 |
| Деталь: | ERR070SKZN3A |
| Парткод: | 4842090314 |
| Деталь: | ERR050SKZN3A |
| Парткод: | 4842090312 |
| Деталь: | 9HSS30/04MSFB |
| Парткод: | 4842011062 |
| Деталь: | ERR040SKZN3A |
| Парткод: | 4842090311 |
| Деталь: | TPAN4008MSZN3L |
| Парткод: | 4842040060 |
| Деталь: | CATCH-CST-320 |
| Парткод: | 44201601000 |
| Деталь: | K-STAY-OPT |
| Парткод: | 44202280000 |
| Деталь: | K-BRKT-FAN-MID |
| Парткод: | 44201153000 |
| Деталь: | FAN-DC-320 |
| Парткод: | 44205160000 |
| Деталь: | CLP/W-LWS-3U |
| Парткод: | 4843390856 |
| Деталь: | ASM-OPT-F320 |
| Парткод: | 44202200000 |
| Деталь: | ASM-SCREW-OPT |
| Парткод: | 4408357160 |
| Деталь: | SCREW-M4-7-R |
| Парткод: | 4842041800 |
| Деталь: | BRKT-HINGE |
| Парткод: | 44200810000 |
| Деталь: | CLP/W-LWS-4U |
| Парткод: | 4843390857 |
| Деталь: | CLP/W-LWS-2U |
| Парткод: | 4843390855 |
| Деталь: | BD/W-EDS-1717U |
| Парткод: | 4843391164 |
| Деталь: | COV-CASE-PWA-R |
| Парткод: | 44201070000 |
| Деталь: | K-COV-PWA-F |
| Парткод: | 44201193000 |
| Деталь: | CLP/W-LWS-8SL25 |
| Парткод: | 4843391707 |
| Деталь: | SHILED-PWA-IH |
| Парткод: | 44203041000 |
| Деталь: | BD/W-EDS-1 |
| Парткод: | 4843390941 |
| Деталь: | K-BRKT-DUCT-1 |
| Парткод: | 44201122000 |
| Деталь: | BRKT-DUCT-2 |
| Парткод: | 44201132000 |
| Деталь: | SEAL-DUCT-2 |
| Парткод: | 44201128000 |
| Деталь: | LOUVER-DUCT-2 |
| Парткод: | 44201158000 |
| Деталь: | COV-FILTER-FAN |
| Парткод: | 44201156000 |
| Деталь: | FILTER-MID-FAN |
| Парткод: | 44201157000 |
| Деталь: | CLP/W-FLC-10S |
| Парткод: | 4843391674 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | TPAN4008MSZN3L |
| Парткод: | 4842040060 |
| Деталь: | TPAN-4035MSZN3L |
| Парткод: | 4842040386 |
| Деталь: | PTBR4008MSZN3A |
| Парткод: | 4842040849 |
| Деталь: | PAN4008MSZN3AI |
| Парткод: | 7040400811 |
| Деталь: | COVER-HTR-CNCT |
| Парткод: | 44204745000 |
| Деталь: | GROMET-EHP-6U |
| Парткод: | 4842416026 |
| Деталь: | OPT-UNIT-F320-S |
| Парткод: | 44202201000 |
| Деталь: | OPT-UNIT-F320-S |
| Парткод: | 44202203000 |
| Деталь: | MYLAR-FAN-MID |
| Парткод: | 44201159000 |
| Деталь: | brkt-top-f |
| Парткод: | 44200828000 |
| Деталь: | REINF-TOP-F |
| Парткод: | 44200829000 |
| Деталь: | reinf-frame-f |
| Парткод: | 44200830000 |
| Деталь: | BD/W - EDS - 1717U |
| Парткод: | 4843391164 |
| Деталь: | BD/W-EDS-1 |
| Парткод: | 4843390941 |
| Деталь: | SP - CS1A - B2CA |
| Парткод: | 4843232255 |
| Деталь: | CLP/W - LWS - 2U |
| Парткод: | 4843390855 |
| Деталь: | CLP/W - LWS - 3U |
| Парткод: | 4843390856 |
| Деталь: | WH - MAIN - SW - 320 |
| Парткод: | 44205293000 |
| Деталь: | stud-lever-adu |
| Парткод: | 44203227000 |
| Деталь: | stud-knob-rgst |
| Парткод: | 44201901000 |
| Деталь: | brkt-door-sw |
| Парткод: | 44200847000 |
| Деталь: | cover-side-sw |
| Парткод: | 44200510000 |
| Деталь: | COVER - FRM - F - 2 |
| Парткод: | 44200454000 |
| Деталь: | lbl-origin-tnr |
| Парткод: | 44204528000 |
| Деталь: | SZ - DOOR - 140 |
| Парткод: | 4400678360 |
| Деталь: | guide-sw-door |
| Парткод: | 44200852000 |
| Деталь: | stud-door-sw |
| Парткод: | 44200854000 |
| Деталь: | brkt-front-sub |
| Парткод: | 44201008000 |
| Деталь: | guide-drsw-f-tr |
| Парткод: | 44200858000 |
| Деталь: | stud-drsw-f-tr |
| Парткод: | 44200859000 |
| Деталь: | LID-SW |
| Парткод: | 41306165000 |
| Деталь: | shaft-door-sw |
| Парткод: | 44200857000 |
| Деталь: | LBL - CAU - LSR - 320 |
| Парткод: | 44204532000 |
| Деталь: | TPAN4008MSZN3L |
| Парткод: | 4842040060 |
| Деталь: | SZ - AJ8W200ZZ01 |
| Парткод: | 44205164000 |
| Деталь: | SZ - AJ8R2004ZC |
| Парткод: | 44205162000 |
| Деталь: | WH-LGC - FD - 320JU |
| Парткод: | 44205323000 |
| Деталь: | WH - LGC - FD - 320E |
| Парткод: | 44205324000 |
| Деталь: | reinf-frame-f |
| Парткод: | 44200832000 |
| Деталь: | guide-drsw-f-tr |
| Парткод: | 44200865000 |
| Деталь: | ZPAN3008MSZN3C |
| Парткод: | 4842080198 |
| Деталь: | ERR040SKZN3A |
| Парткод: | 4842090311 |
| Деталь: | BRKT-BYP-GEAR |
| Парткод: | 44201962000 |
| Деталь: | GG10S018/10S027 |
| Парткод: | 44201964000 |
| Деталь: | STUD-BYP-GEAR |
| Парткод: | 44201961000 |
| Деталь: | BRKT-PAD-SPT-BP |
| Парткод: | 41316569000 |
| Деталь: | SPRING-PAD-BYP |
| Парткод: | 41316568000 |
| Деталь: | ASM-CLT-G28-CW6 |
| Парткод: | 4401969920 |
| Деталь: | FRAME-BYP-320 |
| Парткод: | 44201951000 |
| Деталь: | CLP/W-UAMS05L |
| Парткод: | 4843391176 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | HLDR-TRAY-BYP |
| Парткод: | 41316562000 |
| Деталь: | PLT-HL-GEAR-BYP |
| Парткод: | 41316561000 |
| Деталь: | COVER-BYP |
| Парткод: | 41316573000 |
| Деталь: | SFT-TRAY-L-BYP |
| Парткод: | 41316581000 |
| Деталь: | WH-SFB-320 |
| Парткод: | 44205268000 |
| Деталь: | BD/W-EDS-1 |
| Парткод: | 4843390941 |
| Деталь: | CUSHION-PAD |
| Парткод: | 4401966410 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | 9HSS30/04MSFB |
| Парткод: | 4842011062 |
| Деталь: | TBID3006MSZN3A |
| Парткод: | 4842040683 |
| Деталь: | BID3006MSCR1AI |
| Парткод: | 4842041899 |
| Деталь: | K-BRAKE-PAD-320 |
| Парткод: | 44201967000 |
| Деталь: | K-BRAKE-PAD-320 |
| Парткод: | 44201968000 |
| Деталь: | ERR040SKZN3A |
| Парткод: | 4842090311 |
| Деталь: | ASM-CH-TR-320 |
| Парткод: | 44203810000 |
| Деталь: | PLT-CASE-TR-320 |
| Парткод: | 44203830000 |
| Деталь: | TERM-TR-R-320 |
| Парткод: | 44203855000 |
| Деталь: | TERM-TR-F-320 |
| Парткод: | 44203850000 |
| Деталь: | MYLAR-TR-GUIDE |
| Парткод: | 44203833000 |
| Деталь: | WIRE-CH-060353 |
| Парткод: | 4400674790 |
| Деталь: | SP-TENSION-CH |
| Парткод: | 4407402190 |
| Деталь: | HANGER-WIRE |
| Парткод: | 4407682120 |
| Деталь: | LID-TR-320 |
| Парткод: | 44203868000 |
| Деталь: | SUPPORTER-320 |
| Парткод: | 44203870000 |
| Деталь: | PLT-TERM-1 |
| Парткод: | 44203860000 |
| Деталь: | SPL-GUIDE-CH-TR |
| Парткод: | 44203845000 |
| Деталь: | CASE-CH-TR-320 |
| Парткод: | 44203820000 |
| Деталь: | TERM-TCH-320 |
| Парткод: | 44203885000 |
| Деталь: | PLT-G-TRM-TCH |
| Парткод: | 44203887000 |
| Деталь: | WH-HVT-TCH-320 |
| Парткод: | 44205322000 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | 12ZPAN3008MSZ3L |
| Парткод: | 4842040237 |
| Деталь: | COVER-TERM-TR |
| Парткод: | 44203847000 |
| Деталь: | SHAFT-DRV-SCAN |
| Парткод: | 44202641000 |
| Деталь: | PLY-WIRE-SCAN |
| Парткод: | 44202642000 |
| Деталь: | K-WIRE-SCAN-F |
| Парткод: | 44202643000 |
| Деталь: | K-WIRE-SCAN-R |
| Парткод: | 44202645000 |
| Деталь: | BRG-608ZZNR |
| Парткод: | 4407545610 |
| Деталь: | PLY/T-2GT063-11 |
| Парткод: | 44202668000 |
| Деталь: | FLANGE-PLY-SCAN |
| Парткод: | 4402804750 |
| Деталь: | BRKT-MOT-SCAN |
| Парткод: | 44202761000 |
| Деталь: | K-M/P-SCAN-320 |
| Парткод: | 44202763000 |
| Деталь: | BRKT-DF-L |
| Парткод: | 44202530000 |
| Деталь: | SFT-OPEN-SNS |
| Парткод: | 44202844000 |
| Деталь: | SPR-OPEN-SNS |
| Парткод: | 44202846000 |
| Деталь: | LVR-OPEN-SNS |
| Парткод: | 44202845000 |
| Деталь: | SPL-DF |
| Парткод: | 44202532000 |
| Деталь: | SZ-GP1A73A |
| Парткод: | 4408683480 |
| Деталь: | BD/W-EDS-2 |
| Парткод: | 4843390942 |
| Деталь: | BRKT-DF-R |
| Парткод: | 44202531000 |
| Деталь: | BD/W-EDS-1717U |
| Парткод: | 4843391164 |
| Деталь: | BLT/T-232-2M-6 |
| Парткод: | 44202540000 |
| Деталь: | SPE-WIRE-TENS |
| Парткод: | 44202660000 |
| Деталь: | SPE-MOT-TNS |
| Парткод: | 44202661000 |
| Деталь: | PWA-F-SDV-320 |
| Парткод: | 44204935000 |
| Деталь: | SPL-DF-GND |
| Парткод: | 44202825000 |
| Деталь: | SHAFT-DF-GND |
| Парткод: | 44202826000 |
| Деталь: | 9HSS40/04MSFB |
| Парткод: | 4842011081 |
| Деталь: | ERR070SKZN3A |
| Парткод: | 7405007031 |
| Деталь: | TPAN4008MSZN3L |
| Парткод: | 4842040060 |
| Деталь: | TBID3006MSZN3L |
| Парткод: | 4842040370 |
| Деталь: | TZPAN3006MSZN3L |
| Парткод: | 4842040690 |
| Деталь: | ZPAN3006MSZN3A |
| Парткод: | 4842080197 |
| Деталь: | K-WIRE-SCAN-F |
| Парткод: | 44202653000 |
| Деталь: | K-WIRE-SCAN-R |
| Парткод: | 44202654000 |
| Деталь: | GUIDE-FEEDER-L |
| Парткод: | 44201890000 |
| Деталь: | SP-CS1A-B2CA |
| Парткод: | 4843232255 |
| Деталь: | GUIDE-FEED-R |
| Парткод: | 44201891000 |
| Деталь: | GUIDE-FEED-SFB |
| Парткод: | 44201892000 |
| Деталь: | SZ-FED-210 |
| Парткод: | 4401983080 |
| Деталь: | WH-TR-SW-320 |
| Парткод: | 44205273000 |
| Деталь: | GUIDE-RGST-L |
| Парткод: | 44201530000 |
| Деталь: | ACT-SW-RGST-N |
| Парткод: | 44201537000 |
| Деталь: | ACT-SW-FEED-1 |
| Парткод: | 44201534000 |
| Деталь: | SPA-RGST-SW |
| Парткод: | 44201535000 |
| Деталь: | SZ-GP1A73A |
| Парткод: | 4408683480 |
| Деталь: | GUIDE-RGST-R |
| Парткод: | 44201540000 |
| Деталь: | WH-RGT-SW-320 |
| Парткод: | 44205272000 |
| Деталь: | GUIDE-COV-FED-L |
| Парткод: | 44201621000 |
| Деталь: | ROLLER-FEED-IDL |
| Парткод: | 44201622000 |
| Деталь: | BUSH-FEED-IDL |
| Парткод: | 44201623000 |
| Деталь: | SPC082-090-0155 |
| Парткод: | 44201625000 |
| Деталь: | MG-CATCH-44 |
| Парткод: | 44200424000 |
| Деталь: | ROLLER-RGST-R |
| Парткод: | 44201490000 |
| Деталь: | PIN |
| Парткод: | 4346312020 |
| Деталь: | GEAR-10S020-08 |
| Парткод: | 4401964660 |
| Деталь: | ROLLER-RGST-L |
| Парткод: | 44201510000 |
| Деталь: | NPIN2-8 |
| Парткод: | 4407403790 |
| Деталь: | GEAR-15-1.0 |
| Парткод: | 4402813190 |
| Деталь: | KNOB-RGST |
| Парткод: | 44201900000 |
| Деталь: | SPRING-2200 |
| Парткод: | 44201494000 |
| Деталь: | BUSH-D6-GCB |
| Парткод: | 4407976990 |
| Деталь: | BUSHING |
| Парткод: | 4346312030 |
| Деталь: | BRKT-SW-RGST |
| Парткод: | 44201538000 |
| Деталь: | GUIDE-OPEN-L |
| Парткод: | 44201627000 |
| Деталь: | ASM-CLT-G28-CC8 |
| Парткод: | 4406547840 |
| Деталь: | 9HSS30/04MSFB |
| Парткод: | 4842011062 |
| Деталь: | KNOB-COVER-FEED |
| Парткод: | 44201624000 |
| Деталь: | SCREW-LOCK-ARM |
| Парткод: | 4400805170 |
| Деталь: | MYLAR-SW-RGST-1 |
| Парткод: | 44201542000 |
| Деталь: | MYLAR-SW-RGST-2 |
| Парткод: | 44201543000 |
| Деталь: | STOPPER-COV-FED |
| Парткод: | 44201629000 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | PTBR4008MSZN3A |
| Парткод: | 4842040849 |
| Деталь: | ERR070SKZN3A |
| Парткод: | 7405007031 |
| Деталь: | ERR050SKZN3A |
| Парткод: | 7405005031 |
| Деталь: | TBID4008MSZN3L |
| Парткод: | 4842040748 |
| Деталь: | PTBR4012MSZN3A |
| Парткод: | 4842040851 |
| Деталь: | GUIDE-COV-FED-L |
| Парткод: | 44201630000 |
| Деталь: | ASM-DEV-320 |
| Парткод: | 44204020000 |
| Деталь: | ROLLER-MGN-320 |
| Парткод: | 44204030000 |
| Деталь: | K-HLDR-MG-F |
| Парткод: | 44204040000 |
| Деталь: | K-HLDR-MG-R |
| Парткод: | 44204042000 |
| Деталь: | K-DOCTOR-MG |
| Парткод: | 44204048000 |
| Деталь: | SPC-PUSH-MG |
| Парткод: | 44204050000 |
| Деталь: | MIXER-1-320 |
| Парткод: | 44204052000 |
| Деталь: | K-MIXER-2-320 |
| Парткод: | 44204053000 |
| Деталь: | RLR-GUIDE-320 |
| Парткод: | 44204055000 |
| Деталь: | PLT-ADJUST-MG |
| Парткод: | 44204057000 |
| Деталь: | GEAR-08H020-MG |
| Парткод: | 44204060000 |
| Деталь: | GEAR-08H021-IDL |
| Парткод: | 44204061000 |
| Деталь: | GG10H026/08H019 |
| Парткод: | 44204062000 |
| Деталь: | GEAR-10H026-MX2 |
| Парткод: | 44204063000 |
| Деталь: | BUSH-061206F-M |
| Парткод: | 44204339000 |
| Деталь: | K-BUSH-MIX1 |
| Парткод: | 44204065000 |
| Деталь: | K-BUSH-MIX2 |
| Парткод: | 44204069000 |
| Деталь: | K-PLT-DEV-R |
| Парткод: | 44204073000 |
| Деталь: | SNR-ATC-121 |
| Парткод: | 4402859550 |
| Деталь: | PLT-DEV-BIAS |
| Парткод: | 44204079000 |
| Деталь: | COV-DEV-FRONT |
| Парткод: | 44204080000 |
| Деталь: | SEAL-SIDE-MG-F |
| Парткод: | 44204084000 |
| Деталь: | SEAL-SIDE-MG-R |
| Парткод: | 44204085000 |
| Деталь: | K-COV-DEV-MIX |
| Парткод: | 44204127000 |
| Деталь: | WH-ATS-320 |
| Парткод: | 44205266000 |
| Деталь: | K-CASING-DEV320 |
| Парткод: | 44204031000 |
| Деталь: | SCREW-HLDR-MG |
| Парткод: | 44204086000 |
| Деталь: | SCREW-COV-IN |
| Парткод: | 4406305940 |
| Деталь: | THMS-DRM-320 |
| Парткод: | 44205158000 |
| Деталь: | K-COV-DEV-MG |
| Парткод: | 44204120000 |
| Деталь: | BRG-L1260DDLY83 |
| Парткод: | 4842210410 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407728150 |
| Деталь: | SEAL-VC6-10-2.5 |
| Парткод: | 4401949290 |
| Деталь: | SEAL-DRUM-320 |
| Парткод: | 44204122000 |
| Деталь: | ERR040SKZN3A |
| Парткод: | 4842090311 |
| Деталь: | ERR050SKZN3A |
| Парткод: | 4842090312 |
| Деталь: | PTBR3008MSZN3A |
| Парткод: | 4842040846 |
| Деталь: | BID3006BSCR3CI |
| Парткод: | 7043300664 |
| Деталь: | ZPANE3008BSNI3E |
| Парткод: | 4842041834 |
Коды ошибок
C01
C04
C13
C14
C15
C16
C18
C1A
C1B
C26
C27
C28
C41
C43
C44
C45
C47
C48
C49
C55
C57
C58
C71
C73
C74
C81
C82
C83
C94
CA1
CA2
CB1
CB2
CB3
CB4
CB5
CB6
CB7
CB8
CB9
CBA
CBB
CBC
CBD
CBE
CBF
CC0
CC1
CC2
CC3
CC4
CC5
CC6
CC8
CC9
CCA
CCB
E01
E02
E03
E09
E11
E12
E13
E14
E15
E16
E19
E20
E21
E22
E30
E31
E32
E33
E34
E35
E36
E3C
E3D
E3E
E40
E41
E42
E43
E44
E45
E48
E51
E52
E55
E71
E72
E73
E74
E91
E92
E93
E94
E9F
EA1
EA2
EA3
EA4
EA5
EA6
EA7
EA8
EA9
EAA
EAB
EAC
EAD
EAE
EAF
EB3
EB5
EB6
F07
F10
F11
Описание
| Error code: | C01 |
| Display: | C01-xxx No Ink Replace Ink Cartridge |
| Description: | Main motor is abnormal |
| Remedy: | Is the main motor working? NO 1. Check if the connector CN1 of the main motor is disconnected. 2. Check if the connector J313 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circutied. 4. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 5. Replace the main motor. 6. Replace the LGC board. YES Is the LED on the main motor board lit without flickering? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 3. Replace the main motor. 4. Replace the LGC board. YES 1. Check if the PLL lock signal J313-11 output from the LGC board is always level “L”? 2. Check if the voltage supplied to the microcomputer input terminal IC10-7 is always “L”? 3. Replace the LGC board. |
| Error code: | C04 |
| Display: | C04-xxx Add Paper |
| Description: | Abnormal feed motor |
| Causes: | 402 Paper detection sensor is OFF (not detecting paper). |
| Remedy: | Is the PFP motor working? (Perform the output check in the test mode: 03-125/175) NO 1. Check if the signal line connector of the feed motor is disconnected. 2. Check if the connector J327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the feed motor board and LGC board are short- or open circuited. 5. Replace the feed motor. 6. Replace the LGC board. YES Is the LED on the feed motor board lit without flashing? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the feed motor board and LGC board are short- or open-circuited. 3. Replace the feed motor. 4. Replace the LGC board. YES Replace the LGC board. |
| Error code: | C13 |
| Description: | 1st cassette tray operation abnormal |
| Remedy: | Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board. |
| Error code: | C14 |
| Description: | 2nd cassette tray operation abnormal |
| Remedy: | Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board. |
| Error code: | C15 |
| Description: | 3rd cassette tray operation abnormal |
| Remedy: | Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board. |
| Error code: | C16 |
| Description: | 4th cassette tray operation abnormal |
| Remedy: | Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board. |
| Error code: | C18 |
| Description: | LCF tray operation abnormal |
| Remedy: | Is the harness between the LGC board and the LCF unit open-circuited? Is the relay connector of the harness between the LGC board and the LCF unit or the connector J105 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: Are the switches and sensors in the LCF unit working properly? Y: 1. Replace the LCF tray motor. 2. Replace the LGC board. N: 1. Replace the sensors and switches. 2. Replace the LCF drive PC board or the LCF tray-down switch PC board. 3. Replace the LGC board. |
| Error code: | C1A |
| Description: | Abnormal tandem LCF end fence motor (Paper can be fed from cassettes other than the tandem LCF cassette.) |
| Remedy: | Is the LCF end fence motor working? (Perform the output check in the test mode: 03-207) NO 1. Check if the connector of the tandem LCF end fence motor is disconnected. 2. Check if the connector J346 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Are the tandem LCF end fence home/stop position sensors working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[7]/[A], /[7]/[B]) NO 1. Check if the connectors of the sensors are disconnected. 2. Check if the connector J346 on the LGC board is disconnected. 3. Check if the slit reaches the sensors. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the driving mechanism is abnormal. 2. Check if the conductor pattern on the LGC board is short- or open-circuited. 3. Replace the LGC board. |
| Error code: | C1B |
| Description: | LCF motor is abnormal (paper can be fed from the cassettes other than the LCF cassette) |
| Remedy: | Is the LCF motor working? (Perform the output check in the test mode: 03-122/172) NO 1. Check if the connector CN1 of the LCF motor is disconnected. 2. Check if the connector CN102 on the LCF board is disconnected. 3. Check if the signal line connector CN100 on the LCF board is disconnected. 4. Check if the power line connector CN101 on the LCF board is disconnected. 5. Check if the connector J312 on the LGC board is disconnected. 6. Check if the connector pins are disconnected and the harnesses are open-circuited. 7. Check if the conductor patterns on the LCF motor board, LCF board and LGC board arer short- or open-circuited. 8. Replace the LCF motor. 9. Replace the LCF board. 10. Replace the LGC board. YES 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the LCF motor board, LCF board and LGC board are short- or open-circuited. 3. Check if the PLL lock signal CN102-3 output from the LCF board is always “L” level. 4. Check if the voltage supplied to the microcomputer input terminal IC103-17 is always “L” level. 5. Replace the LCF motor. 6. Replace the LCF board. 7. Replace the LGC board. |
| Error code: | C26 |
| Description: | Peak detection error |
| Remedy: | Does the exposure lamp light? (Perform the output check in the test mode: 03-267) YES 1. Check if the connectors on the CCD and SLG boards are disconnected. 2. Check if the shading correction plate is dirty. 3. Check if the conductor pattern on the CCD board is short- or open-circuited. 4. Check if the conductor pattern on the SLG board is short- or open-circuited. 5. Replace the lens unit. 6. Replace the SLG board. NO 1. Check if the connectors of the exposure lamp and inverter are disconnected. 2. Check the SLG board if the connector pin J9 is disconnected and the harness is short- or opencircuited. 3. Check if the conductor pattern on the SLG board is short- or open-circuited. 4. Replace the SLG board. 5. Replace the inverter. 6. Replace the exposure lamp. |
| Error code: | C27 |
| Description: | Carriage home position sensor not turning OFF within a fixed time |
| Causes: | • If the Master sensor does not find master on the Drum when the Drum is at 79° during the printing movement. |
| Remedy: | Are the carriages stuck at a point other than the home position? Y: Check the SCM and SDV boards for any abnormal circuit. N: 1. Check if any connector pin is disconnected, or any harness is open- or short-circuited. 2. Check the scan motor drive pulley if its screws are loose. 3. Check if any conductor pattern on the SDV board is open- or short-circuited. 4. Check if any conductor pattern on the SCM board is open- or short-circuited. 5. Replace the SDV board. 6. Replace the SCM board. |
| Error code: | C28 |
| Description: | Carriage home position sensor not turning ON within a fixed time |
| Remedy: | Do the carriages, after arriving at its home position, make a big noise? Y: Since the carriage home position sensor has not been turned ON, 1. Check if the sensor connector is disconnected. 2. Check the SDV and SCM boards for any abnormal circuit. N: Since the carriages do not move, 1. Check if any connector pin is disconnected, or any harness is open- or short-circuited. 2. Check if any conductor pattern on the SDV board is open- or short-circuited. 3. Check if any conductor pattern on the SCM board is open- or short-circuited. 4. Replace the SDV board. 5. Replace the SCM board |
| Error code: | C41 |
| Description: | Thermistor or heater abnormal when warming-up is started |
| Causes: | MAIN board Switching regulator |
| Remedy: | 1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally. |
| Error code: | C43 |
| Description: | Thermistor abnormal during warming-up after abnormality judgment |
| Causes: | MAIN board Switching regulator |
| Remedy: | 1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally. |
| Error code: | C44 |
| Description: | Heater abnormal during warming-up after abnormality judgment |
| Causes: | MAIN board Switching regulator |
| Remedy: | 1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally. |
| Error code: | C45 |
| Description: | Abnormal side thermistor after the copier has become ready |
| Causes: | MAIN board Switching regulator |
| Remedy: | 1. Check the side thermistor (1) Check if the connector is disconnected. (2) Check if the side thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the side thermistor is open-circuited. 2. Check the LGC board (1) Check if the connector J334 is disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) “6” to “0”. |
| Error code: | C47 |
| Description: | Rear thermistor abnormal after the copier has become ready |
| Remedy: | 1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally. |
| Error code: | C48 |
| Description: | Heater abnormal (high temperature) |
| Remedy: | 1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally. |
| Error code: | C49 |
| Description: | Abnormal IH circuit or coil |
| Causes: | • If the actuator of the Master disposal unit set switch is not depressed. |
| Remedy: | 1. Check the IH control board (1) Check if the conductor pattern on the board is short or open-circuited. (2) Replace the IH control board. 2. Check the IH coil (1) Check if the coil is broken or shorted. (2) Replace the IH coil. 3. Clear the status counter Change the values “13”, “15”, “16” or “19” of the status counter (08-400) to “0”. * The status counter value is as follows in the following cases. Change them to "0" respectively. • The error occurred before the temperature of the fuser roller reaches 40°C: "13" • The error occurred before the temperature of the fuser roller reaches 150°C: "16" • The error occurred before the machine has become ready: "15" • The error occurred when the machine is in the ready state: "19" [C47], [C48] and [C49] can be cleared by turning OFF and ON the main switch as long as the problem was solved, and the status counter does not have to be changed to "0". The value of the status counter remains until the next service call overwrites the value. |
| Error code: | C55 |
| Description: | RADF I/F error |
| Remedy: | Is the harness between the ADF board and SLG board open-circuited? Replace the harness. Is the ADF board short- or open-circuited? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. Replace the SLG board. |
| Error code: | C57 |
| Description: | Communications error between LGC-CPU and IPC board |
| Remedy: | (1) Check if any conductor pattern on the LGC board, mainly around IC23, IC72, IC74 and J125, is short- or open-circuited. (2) Check if the conductor pattern on the IPC board is short- or open-circuited. (3) Replace the IPC board. (4) Replace the LGC board. |
| Error code: | C58 |
| Description: | Communication error between IPC board and finisher |
| Causes: | • If the actuator of the Master making unit set switch is not depressed. |
| Remedy: | Is a specified finisher used? Replace to the specified finisher. Is the harness between the IPC board and finisher control board open-circuited? Replace the harness. Is the conductor pattern on the IPC board is short- or open-circuited? Replace the IPC board. Replace the finisher control board. |
| Error code: | C71 |
| Description: | ADF feed motor is abnormal |
| Remedy: | (1) Check if the load on the motor shaft is normal. (2) Check the mechanical load and adjust the drive system. Remove foreign objects. (3) Check if the power is supplied to connector CN11 of the motor. (4) Check the circuits and connectors on the ADF control board, mainly IC6, Q19, Q20, Q21, Q22 and CN11, for short- and open-circuits. (5) Replace the ADF control board. (6) Replace the ADF feed motor. |
| Error code: | C73 |
| Description: | EEPROM initializing error |
| Remedy: | 1. Check if any conductor pattern on the RADF PC board is open- or short-circuited mainly around IC7. 2. Replace the RADF PC board. 3. Initialize the RADF`s EEPROM and perform the sensor automatic adjustment. |
| Error code: | C74 |
| Description: | Paper exit sensor automatic adjustment error |
| Remedy: | 1. Check if any foreign matter is present between the exit sensor and the reflecting mirror, and if the reflecting mirror is stained. 2. Check if the harness between the exit sensor and the RADF PC board is open-circuited. 3. Check if any conductor pattern on the RADF PC board is open- or short-circuited mainly around IC1, IC14 and CN8. 4. Replace the exit sensor. 5. Replace the RADF PC board. 6. Initialize the RADF`s EEPROM and perform the sensor automatic adjustment. |
| Error code: | C81 |
| Description: | Transport motor trouble |
| Remedy: | [Procedure 1] Is the No.2 transport motor (M8) operating in reverse at the fixed timing? No Replace the transport motor or finisher controller board. Yes Is the shutter correctly coupled to the shutter upper/lower bars? No Correctly couple. Yes Try turning transport roller 2 in reverse by hand. Do the shutter upper/lower bars move up and down? No Correct the mechanism from the shutter upper/lower bars up to the gears of transport roller 2. Yes Is the shutter close detection switch (MS4) normal? No Replace the switch. Yes Replace the finisher controller board. [Procedure 2] Is the No.2 transport motor (M8) operating in reverse at the fixed timing? No Replace the transport motor or finisher controller board. Yes Is the shutter correctly coupled to the shutter upper/lower bars? No Correctly couple. Yes Try turning transport roller 2 in reverse by hand. Do the shutter upper/lower bars move up and down? No Correct the mechanism from the shutter upper/lower bars up to the gears of transport roller 2. Yes Is the shutter open sensor (PI5) normal? No Replace the sensor. Yes Replace the finisher controller board. |
| Error code: | C82 |
| Description: | Communications error between scanner and ADF |
| Remedy: | 1. Check if the connectors are disconnected or the harnesses are open-circuited between the SCM board and RADF PC board (includig the relay connector). 2. Replace the RADF PC board. 3. Replace the SCM board. |
| Error code: | C83 |
| Description: | Original length sensor adjustment error |
| Remedy: | Is there any extraneous material between the original length sensor and reflective mirror? Remove the extraneous material. Is the reflective mirror tainted? Clean up the mirror. Is the conductor pattern around IC6, IC11 and CN15 on the ADF board short- or open-circuited? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. 1. Replace the original length sensor. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. |
| Error code: | C94 |
| Description: | LGC-CPU abnormal |
| Remedy: | Is "Call for service" displayed again even after the copier is turned OFF and then back ON? N: Observe the condition for a while. Y: 1. Check if the conductor pattern between LGC-CPU (IC32) and FROM (IC24) is open- or short-circuited. 2. If this problem recurs frequently, replace the LGC board. |
| Error code: | CA1 |
| Description: | Polygonal motor rotation abnormal |
| Remedy: | Is the polygonal motor rotating? N: 1. Check if the polygonal motor connector is disconnected. 2. Check if connector J181 or J188 on the IMC board is disconnected. 3. Check if any harness is open-circuited or any connector pin is disconnected. 4. Check if any conductor pattern on the IMC board is open- or short-circuited. 5. Replace the IMC board. 6. Replace the laser optical unit. Y: Are both 10th and 12th pins of the connector J188 on the IMC board always at the level "L"? N: 1. Check if any conductor pattern on the IMC board is open- or short-circuited . 2. Replace the IMC board. 3. Replace the laser optical unit. Y: 1. Check if any conductor pattern on the IMC board is open- or short-circuited . 2. Replace the IMC board. 3. Replace the laser optical unit. |
| Error code: | CA2 |
| Description: | H-SYNC abnormal |
| Remedy: | Is the polygonal motor rotating? N: Refer to "[CA1] Polygonal motor rotation abnormal". Y: Are both 10th and 12th pins of the connector J188 on the IMC board always at the level "L"? N: Refer to "[CA1] Polygonal motor rotation abnormal". Y: Is the harness between the RLY and IMC boards open-circuited? Are the connector J185 on the IMC board or the connector J201 on the RLY board disconnected? Y: Replace the harness. Reconnect the connectors. N: 1. Replace the IMC board. 2. Replace the laser optical unit. |
| Error code: | CB1 |
| Description: | Feed motor abnormal |
| Remedy: | [Procedure 1] Is the second feed motor (M8) rotating in reverse at the specified timing? N: Replace the second feed motor or the finisher controller PC board. Y: Is the shutter securely attached to the shutter upper/lower bars? N: Attach it securely. Y: Turn the feed roller-2 in reverse by hand. Do the shutter upper/lower bars move up and down? N: Correct the mechanism from the shutter upper/lower bars to the gears of the feed roller-2. Y: Is the shutter closed detecting switch (MS4) working normally? N: Replace the switch. Y: Replace the finisher controller PC board. [Procedure 2] Is the second feed motor (M8) rotating in reverse at the specified timing? N: Replace the second feed motor or the finisher controller PC board. Y: Is the shutter securely attached to the shutter upper/lower bars? N: Attach it securely. Y: Turn the feed roller-2 in reverse by hand. Do the shutter upper/lower bars move up and down? N: Correct the mechanism from the shutter upper/lower bars to the gears of the feed roller-2. Y: Is the shutter open sensor (PI5) working normally? N: Replace the sensor. Y: Replace the finisher controller PC board. [Procedure 3] Check the safety zone switch (MS3). Is the switch working normally? N: Replace the switch. Y: Is the safety zone switch (MS3) correctly pressed? N: Correct the mechanism. Y: Is the shutter closed detecting switch (MS4) working normally? N: Replace the switch. Y: Is the shutter closed detecting switch (MS4) correctly pressed? N: Correct the mechanism. Y: Replace the finisher controller PC board. |
| Error code: | CB2 |
| Description: | Delivery motor abnormal |
| Remedy: | Rotate the delivery motor by hand. Does it rotate smoothly? N: Correct the mechanism. Y: Is the delivery motor clock sensor (PI10) working normally? N: Replace the sensor. Y: Does the voltage between J11-4 and -5 on the finisher controller PC board become 24V when the delivery motor starts rotating? N: Replace the finisher controller PC board. Y: Is the wiring between the delivery motor and finisher controller PC board correct? N: Correct the wiring. Y: Replace the motor. |
| Error code: | CB3 |
| Description: | Tray lift motor abnormal |
| Remedy: | [Procedure 1] Is the tray home position sensor (PI8) working normally? N: Replace the sensor. Y: Is the tray elevation mechanism normal? N: Correct the mechanism. Y: Is 24V DC supplied to the tray lift motor (M5) from the finisher controller PC board when the tray is being driven? N: Replace the finisher controller PC board. Y: Is the wiring between the finisher controller PC board and the tray lift motor (M5) correct? N: Correct the wiring. Y: Replace the tray lift motor (M5). [Procedure 2] Does the tray reach the tray upper limit detecting switch (MS5)? Y: Lower the position of the tray. N: Is the tray upper limit detecting switch (MS5) working normally? N: Replace the switch. Y: Is the wiring between the finisher controller PC board and the tray upper limit detecting switch correct? N: Correct the wiring. Y: Replace the finisher controller PC board. [Procedure 3] Does the tray move up/down? N: Is the power supplied to the motor from the finisher controller PC board when the tray is moving? N: Replace the finisher controller PC board. Y: Is there any problem with the tray elevation mechanism? N: Replace the tray lift motor (M5). Y: Correct the tray elevation mechanism. Y: Are the tray lift motor clock sensor-1/-2 (PI9/PI19) working normally? N: Replace the sensors. Y: Replace the finisher controller PC board. |
| Error code: | CB4 |
| Description: | Alignment motor abnormal |
| Remedy: | Is the alignment guide home position sensor (PI6) working normally? N: Replace the sensor. Y: Is the wiring between the finisher controller PC board and the alignment motor (M3) correct? N: Correct the wiring. Y: Is there any mechanical problem with the alignment guide movement path? Y: Correct the mechanism. N: Is the problem solved by replacing the alignment motor? N: Replace the finisher controller PC board. Y: End |
| Error code: | CB5 |
| Description: | Staple motor abnormal |
| Remedy: | Is the wiring between the stapler and the finisher controller PC board correct? N: Correct the wiring. Y: Is the problem solved by replacing the stapler? N: Replace the finisher controller PC board. Y: End |
| Error code: | CB6 |
| Description: | Stapler shift motor abnormal |
| Remedy: | Is the stapler shift home position sensor (PI7) working normally? N: Replace the sensor. Y: Is the wiring between the finisher controller PC board and the stapler shift motor (M4) correct? N: Correct the wiring. Y: Is there any mechanical problem with the stapler stand motion path? Y: Correct the mechanism. N: Is the problem solved by replacing the stapler shift motor? N: Replace the finisher controller PC board. Y: End |
| Error code: | CB7 |
| Description: | Height sensor abnormal |
| Remedy: | [Procedure 1] Is the problem solved by turning the power of the copier OFF and ON Y: End N: Is the wiring between the finisher controller PC board and the height sensor (PS1) correct? N: Correct the wiring. Y: Is the voltage between J6-2(+) and J6-4(-) on the finisher controller PC board 5V DC? N: Replace the finisher controller PC board. Y: Readjust the height sensor. Replace the height sensor if it still causes the problem. [Procedure 2] Is the connector J6 on the finisher controller PC board, J114 of the height sensor (PS1) or relay connector J212 disconnected? Y: Connect the connector. N: Is the voltage between J6-2(+) and J6-4(-) on the finisher controller PC board 5V DC? N: Replace the finisher controller PC board. Y: Is the wiring between the finisher controller PC board and height sensor correct? N: Correct the wiring. Y: Replace the height sensor. [Procedure 3] Is the problem solved by readjusting the DIP switch? Y: End N: Is the wiring between the finisher controller PC board and height sensor (PS1) correct? N: Correct the wiring. Y: Is the voltage between J6-2(+) and J6-4(-) on the finisher controller PC board 5V DC? N: Replace the finisher controller PC board. Y: Replace the height sensor. |
| Error code: | CB8 |
| Description: | Backup RAM data abnormal |
| Remedy: | Is the problem solved by turning the power of the copier OFF and ON? Y: End N: Is the problem solved by replacing the finisher controller PC board? N: Replace the punch driver PC board. Y: End |
| Error code: | CB9 |
| Description: | Saddle stitcher/paper pushing plate motor abnormal |
| Remedy: | [Procedure 1] Is the paper pushing plate home position sensor (PI14S) working normally? N: Replace the sensor. Y: Is the paper pushing plate motor (M8S) operating at the specified timing? Y: Replace the saddle stitcher controller PC board. N: Is the paper pushing plate drive mechanism normal? N: Correct the mechanism. Y: Is the problem solved by replacing the paper pushing plate motor (M8S)? N: Replace the saddle stitcher controller PC board. Y: End [Procedure 2] Is the paper pushing plate top position sensor (PI15S) working normally? N: Replace the sensor. Y: Is the paper pushing plate motor (M8S) operating at the specified timing? Y: Replace the saddle stitcher controller PC board. N: Is there any problem with the paper pushing plate drive mechanism? Y: Correct the mechanism. N: Is the problem solved by replacing the paper pushing plate motor (M8S)? N: Replace the saddle stitcher controller PC board. Y: End [Procedure 3] Is the paper pushing plate motor clock sensor (PI1S) working normally? N: Replace the sensor. Y: Is the paper pushing plate motor (M8S) operating at the specified timing? Y: Replace the saddle stitcher controller PC board. N: Is there any problem with the pushing plate drive mechanism? Y: Correct the mechanism. N: Is the problem solved by replacing the paper pushing plate motor (M8S)? N: Replace the saddle stitcher controller PC board. Y: End |
| Error code: | CBA |
| Description: | Saddle stitcher/stitcher motor (front) abnormal |
| Remedy: | Are the front or rear stitcher and its stand installed properly? N: Install them properly. Y: Is the stitcher home position switch on the front or rear stitcher (MS7S/MS5S) working normally? N: Replace the front or rear stitcher. Y: Is the front or rear stitcher operating at the specified timing? N: Replace the front or rear stitcher. Y: Check the wiring between the stitcher and saddle stitcher controller PC board. If there is no problem, replace the controller PC board. |
| Error code: | CBB |
| Description: | Saddle stitcher/stitcher motor (rear) abnormal |
| Remedy: | Are the front or rear stitcher and its stand installed properly? N: Install them properly. Y: Is the stitcher home position switch on the front or rear stitcher (MS7S/MS5S) working normally? N: Replace the front or rear stitcher. Y: Is the front or rear stitcher operating at the specified timing? N: Replace the front or rear stitcher. Y: Check the wiring between the stitcher and saddle stitcher controller PC board. If there is no problem, replace the controller PC board. |
| Error code: | CBC |
| Description: | Saddle stitcher/alignment motor abnormal |
| Remedy: | Is the alignment plate home position sensor (PI5S) working normally? N: Replace the sensor. Y: Is the alignment motor (M5S) operating at the specified timing? Y: Replace the saddle stitcher controller PC board. N: Is the alignment plate drive mechanism normal? N: Correct the mechanism. Y: Is the problem solved by replacing the alignment motor (M5S)? N: Replace the saddle stitcher controller PC board. Y: End |
| Error code: | CBD |
| Description: | Saddle stitcher/guide motor abnormal |
| Remedy: | Is the guide home position sensor (PI13S) working normally? N: Replace the sensor. Y: Is the guide motor (M3S) operating at the specified timing? Y: Replace the saddle stitcher controller PC board. N: Is the guide plate drive mechanism normal? N: Correct the mechanism. Y: Is the problem solved by replacing the guide motor (M3S)? N: Replace the saddle stitcher controller PC board. Y: End |
| Error code: | CBE |
| Description: | Saddle stitcher/paper folding motor abnormal |
| Remedy: | Is the paper folding motor clock sensor (PI4S) working normally? N: Replace the sensor. Y: Is the paper folding home position sensor (PI21S) working normally? N: Replace the sensor. Y: Is the paper folding motor (M2S) operating at the specified timing? Y: Replace the saddle stitcher controller PC board. N: Is the paper folding roller drive mechanism normal? N: Correct the mechanism. Y: Is the problem solved by replacing the paper folding motor (M2S)? N: Replace the saddle stitcher controller PC board. Y: End |
| Error code: | CBF |
| Description: | Saddle stitcher/paper positioning plate motor abnormal |
| Remedy: | Is the paper positioning plate home position sensor (PI7S) working normally? N: Replace the sensor. Y: Is the paper positioning plate operating at the specified timing? Y: Replace the saddle stitcher controller PC board. N: Is the paper positioning plate drive mechanism normal? N: Correct the mechanism. Y: Is the problem solved by replacing the paper positioning plate motor (M4S)? N: Replace the saddle stitcher controller PC board. Y: End |
| Error code: | CC0 |
| Description: | Abnormal saddle stitcher sensor connector connection |
| Remedy: | [Procedure 1] Is the guide home position sensor (PI13S) connected to the saddle stitcher controller PC board? NO Connect it to the board. YES Is the wiring between the sensor and the saddle stitcher correct? YES Correct the wiring. NO Is 1 or 2V DC being supplied from J9-7 on the saddle stitcher controller PC board? NO Replace the saddle stitcher controller PC board. YES Is J9-11 on the saddle stitcher controller PC board correctly connected to the ground? NO Replace the saddle stitcher controller PC board. YES END [Procedure 2] Is the paper pushing plate home position sensor (PI14S) connected to the saddle stitcher controller PC board? NO Connect it to the board. YES Is the wiring between the sensor and the saddle stitcher correct? YES Correct the wiring. NO Is 1 or 2V DC being supplied from J9-10 on the saddle stitcher controller PC board? NO Replace the saddle stitcher controller PC board. YES Is J9-11 on the saddle stitcher controller PC board properly connected to the ground? NO Replace the saddle stitcher controller PC board. YES END [Procedure 3] Is the paper pushing plate top position sensor (PI15S) connected to the saddle stitcher controller PC board? NO Connect it to the board. YES Is the wiring between the sensor and the saddle stitcher correct? YES Correct the wiring. NO Is 1 or 2V DC being supplied from J9-13 on the saddle stitcher controller PC board? NO Replace the saddle stitcher controller PC board. YES Is J9-14 on the saddle stitcher controller PC board properly connected to the ground? NO Replace the saddle stitcher controller PC board. YES END |
| Error code: | CC1 |
| Description: | Abnormal saddle stitcher microswitch |
| Remedy: | [Procedure 1] Is the switch actuator for the inlet door working properly? NO Fix the mechanism. YES Is the inlet cover switch (MS1S) working normally? NO Replace the switch. YES Measure the voltage of J10-8 on the saddle stitcher controller PC board when the inlet door is open. Is it 5V? NO The inlet cover sensor (PI9S) is broken. Replace it. YES Measure the voltage between J19-2 (+) and J19-1 (-) on the saddle stitcher controller PC board. Is it 24 V? NO Replace the saddle stitcher controller PC board. YES Check the wiring between J19 on the finisher controller PC board and J1 on the saddle stitcher controller PC board. If there is no problem, replace the saddle stitcher controller PC board. [Procedure 2] Is the switch actuator for the front door working properly? NO Fix the mechanism. YES Is the front cover switch (MS2S) working normally? NO Replace the switch. YES Measure the voltage of J11-12 on the saddle switcher controller PC board when the front door is opened. Is it 5V? NO The front door opening/closing sensor is broken. Replace it. YES Replace the saddle stitcher controller PC board. [Procedure 3] Is the switch actuator for the delivery door working properly? NO Fix the mechanism. YES Is the delivery cover switch working normally? NO Replace the switch. YES Measure the voltage of J11-9 on the saddle stitcher controller PC board when the delivery door is opened. Is it 5V ? NO The delivery cover sensor (PI3S) is broken. Replace it. YES Replace the saddle stitcher controller PC board. |
| Error code: | CC2 |
| Description: | Abnormal communication between finisher and saddle stitcher |
| Remedy: | Is the problem solved by turning OFF and ON the power switch of the copier? YES END NO Is the wiring between the finisher controller PC board and the saddle stitcher controller PC board connected? YES Connect the wiring. NO Measure the voltage between J3-2 (+) and J3-1 (-) on the finisher controller PC board. Is it DC 5V? NO Replace the finisher controller PC board. YES Replace the saddle stitcher controller PC board. |
| Error code: | CC3 |
| Description: | Stack processing motor is abnormal |
| Remedy: | MJ-1011 [Procedure 1] Is the tension of the drive belt normal? NO Loosen the adjustment screw to adjust the tension. YES Does the bushing attached to the returing roller shaft smoothly move up and down? NO Apply grease on the cut-out part of the front side frame with where the bushing contacts. YES Is the spring of the returing roller detached? YES Attach the spring. YES Is the wiring between the finisher controller PC board and stack processing motor correct? YES Correct the wiring. YES Is the stack delivery lever home position sensor (S8) working properly? NO Replace the sensor. YES Is the problem solved by replacing the stack processing motor? NO Replace the finisher controller PC board. YES END [Procedure 2] Does the bushing attached to the returning roller shaft smoothly move up and down? NO Apply grease on the cut-out part of the front side frame with where the bushing contacts. YES Is the spring of the returning roller detached? YES Attach the spring. YES Is the tension of the stack processing motor drive belt normal? NO Loosen the adjustment screw to adjust the tension. YES Is the returning roller home position sensor (S3) working properly? NO Replace the sensor. YES Is the problem solved by replacing the stack processing motor? NO Replace the finisher controller PC board. YES END |
| Error code: | CC4 |
| Description: | Abnormal swing motor |
| Remedy: | [Procedure 1] Rotate the swing motor in reverse by hand. Does the swing guide move up and down? NO Fix the swing mechanism. YES Is the swing guide closed detection switch-2 (MS6) working normally? NO Replace the switch. YES Is the swing guide open sensor (PI18) working normally? NO Replace the sensor. YES Is the swing motor (M7) rotating in reverse at the fixed timing? NO Replace the motor. YES END [Procedure 2] Is the safety zone switch (MS3) working normally? NO Replace the switch. YES Is the safety zone switch (MS3) correctly pressed? NO Fix the mechanism. YES Is the swing guide closed detection switch-2 (MS6) working normally? NO Replace the switch. YES Is the swing guide closed detection switch-2 (MS6) correctly pressed? NO Fix the mechanism. YES Replace the finisher controller PC board. [Procedure 3] Is the swing motor clock sensor (PI20) working normally? NO Replace the sensor. YES Does the voltage between J11-6 and -7 on the finisher controller PC board become 24V when the swing motor starts rotating? NO Replace the finisher controller PC board. YES Is the wiring between the swing motor and finisher controller PC board correct? YES Correct the wiring. NO Replace the swing motor. |
| Error code: | CC5 |
| Description: | Abnormal horizontal registration motor |
| Remedy: | Is the horizontal registration home position sensor (PI1P) working normally? NO Replace the sensor. YES Is the wiring between the horizontal registration home position sensor (PI1P) and finisher controller PC board correct? YES Correct the wiring. NO Is the horizontal registration mechanism normal? NO Fix the mechanism. YES Is the problem solved by replacing the horizontal registration motor (M2P)? YES END NO Is the problem solved by replacing the punch motor? YES END NO Is the problem solved by replacing the punch driver board? YES END NO Replace the finisher controller PC board. |
| Error code: | CC6 |
| Description: | Abnormal punch motor |
| Remedy: | Is the punch home position sensor (PI3P) working normally? NO Replace the sensor. YES Is the wiring between the punch home position sensor (PI3P) and finisher controller PC board correct? YES Correct the wiring. NO Is the punching mechanism normal? NO Fix the mechanism. YES Is the problem solved by replacing the punch motor (M1P) ? YES END NO Is the problem solved by replacing the punch driver board? YES END NO Replace the finisher controller PC board. |
| Error code: | CC8 |
| Description: | Front jogging motor is abnormal |
| Remedy: | MJ-1011 Is the front jogging plate home position sensor (S6) working properly? NO Replace the sensor. YES Is the wiring between the finisher controller PC board and front jogging motor correct? NO Correct the wiring. YES Has the rack run over the stopper of the roll? YES Fix it. NO Is the problem solved by replacing the front jogging motor? NO Replace the finisher controller PC board. YES END |
| Error code: | CC9 |
| Description: | Upper stack tray lift motor is abnormal |
| Remedy: | MJ-1011 Is the wiring between the finisher controller PC board and upper stack tray lift motor correct? NO Correct the wiring. YES Are the front and rear sides of the upper stack tray leveled? NO Level them. YES Is the upper stack tray lift motor clock sensor (S19) working properly? NO Replace the sensor. YES Is the stack tray paper height sensor (S10) working properly? NO Replace the sensor. YES Are the upper stack tray upper limit sensor (S25), lower stack tray full sensor (S23) and stack processing safety switch working properly? NO Replace the sensor or sensor controller PC board. YES Does the voltage between the pins J14-1 and -2 on the finisher controller PC board become 24V when the upper stack tray lift motor starts rotating? NO Replace the finisher controller PC board. YES t t t t t t t t Check the wiring between the upper stack tray lift motor and finisher controller PC board. If there is no problem, replace the upper stack tray lift motor. |
| Error code: | CCA |
| Description: | Lower stack tray lift motor is abnormal |
| Remedy: | MJ-1011 Is the wiring between the finisher controller PC board and lower stack tray lift motor correct? NO Correct the wiring. YES Are the front and rear sides of the lower stack tray leveled? NO Level them. YES Is the lower stack tray lift motor clock sensor (S19) working properly? NO Replace the sensor. YES Is the stack tray paper height sensor (S10) working properly? NO Replace the sensor. YES Are the lower stack tray upper limit sensor (S13) and lower stack tray lower limit sensor (S12) working properly? NO Replace the sensor or sensor controller PC board. YES Does the voltage between the pins J3-1 and -2 on the finisher controller PC board become 24V when the lower stack tray lift motor starts rotating? NO Replace the finisher controller PC board. YES t t t t t t t t Check the wiring between the upper stack tray lift motor and finisher controller PC board. If there is no problem, replace the lower stack tray lift motor. |
| Error code: | CCB |
| Description: | Rear jogging motor is abnormal |
| Remedy: | MJ-1011 Is the rear jogging plate home position sensor (S7) working properly? NO Replace the sensor. YES Is the wiring between the finisher controller PC board and rear jogging motor correct? NO Correct the wiring. YES Has the rack run over the stopper of the roll? YES Fix it. NO Is the problem solved by replacing the rear jogging motor? NO Replace the finisher controller PC board. YES END |
| Error code: | E01 |
| Description: | Paper leading edge not reaching the exit sensor |
| Remedy: | Is the fuser motor rotating? Y: Is the harness between the LGC board and the exit sensor open-circuited? Is the connector of the paper exit sensor or the connector J123 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the exit sensor. 2. Replace the LGC board. N: Is the harness between the LGC board and the paper exit sensor open-circuited? Is the fuser motor connector or the connector J122 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the fuser motor. 2. Replace the LGC board. Where was the paper stopped? Near the exit sensor (paper not damaged) Are the registration seRemove the paper after the fuser unit cools down.nsor and paper exit sensor functioning properly? (Does the actuator return normally?) Y: 1. In the tRemove the paper after the fuser unit cools down.est mode (03) check if each sensor is functioning. 2. Reconnect each sensor connector. N: Repair the actuator if it has come off. Before reaching the fuser unit Did the paper stop, curling upward excessively? Y: Replace the paper in the cassette. From the transfer belt surface to the exit sensor Do the size of paper and the size set match? N: Make the sizes match. Y: Is the transfer belt moving? Is the black drum motor or the transfer belt motor stopped? Or is any abnormal noise heard from one of them due to loss of synchronism? Y: 1. Reduce the mechanical load by adjusting the drive system. Remove any foreign matter. 2. Check the motor connector, and the connector J130 on the LGC board. 3. Replace the motor. 4. Replace the LGC board. No paper found Is the paper attached to the fuser belt? Remove the paper after the fuser unit cools down. |
| Error code: | E02 |
| Display: | E02-xxx !!Maintenance!! Call Service |
| Description: | Paper trailing edge not passing the exit sensor |
| Remedy: | Is the fuser motor rotating? Y: Is the harness between the LGC board and the exit sensor open-circuited? Is the connector of the paper exit sensor or the connector J123 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the exit sensor. 2. Replace the LGC board. N: Is the harness between the LGC board and the paper exit sensor open-circuited? Is the fuser motor connector or the connector J122 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the fuser motor. 2. Replace the LGC board. Where was the paper stopped? Near the exit sensor (paper not damaged) Are the registration seRemove the paper after the fuser unit cools down.nsor and paper exit sensor functioning properly? (Does the actuator return normally?) Y: 1. In the tRemove the paper after the fuser unit cools down.est mode (03) check if each sensor is functioning. 2. Reconnect each sensor connector. N: Repair the actuator if it has come off. Before reaching the fuser unit Did the paper stop, curling upward excessively? Y: Replace the paper in the cassette. From the transfer belt surface to the exit sensor Do the size of paper and the size set match? N: Make the sizes match. Y: Is the transfer belt moving? Is the black drum motor or the transfer belt motor stopped? Or is any abnormal noise heard from one of them due to loss of synchronism? Y: 1. Reduce the mechanical load by adjusting the drive system. Remove any foreign matter. 2. Check the motor connector, and the connector J130 on the LGC board. 3. Replace the motor. 4. Replace the LGC board. No paper found Is the paper attached to the fuser belt? Remove the paper after the fuser unit cools down. |
| Error code: | E03 |
| Description: | Paper remaining inside the copier at power ON |
| Remedy: | Is any paper remaining inside the copier? Y: Remove the paper. N: Refer to [E01], [E02] and [E11] to [E26]. |
| Error code: | E09 |
| Description: | Jam caused by an abnormal HDD |
| Remedy: | (1) Check if the connectors of the HDD are disconnected. (2) Check if the connector pins are disconnected and the harnesses are open-circuited. (3) Replace the HDD. (4) Replace the SYS board. |
| Error code: | E11 |
| Description: | Paper misfeed from the ADU |
| Remedy: | Is any paper remaining in the paper feed area inside the ADU? Y: Remove the paper. N: Is the connector J104 on the LGC board disconnected? Is the harness between the LGC board and the ADU drawer connector open-circuited? Y: Reconnect the connector. Replace the harness. N: 1. Replace the LGC board. 2. Replace the ADU. |
| Error code: | E12 |
| Display: | E12-Output Bin Full, Top |
| Description: | Top Output Tray is Full, Unload Paper |
| Remedy: | 1 Visually inspect the Stack Full Actuator and use service diagnostics to test the Stack Full Sensor. Does the sensor and actuator operate correctly? Go to step [3]. Replace the actuator if broken. If the sensor is not working, go to step [2}. 2 Check Pin 6 OPTN cable at the Engine Controller Board for +5 volts. Replace the Engine Controller Board. Go to step [3]. 3 Check the Stack Full Sensor wiring harness to the Toner Sensor Board Pin 3 for +5 volts. Go to step [4]. Replace the Stack Full Sensor and wiring. 4 Check for +5 volts at Pin 6 OPTN cable to the Toner Sensor Board. Replace the ribbon cable (OPTN) Replace the Toner Sensor Board. |
| Error code: | E13 |
| Description: | Paper misfeed from the 1st cassette |
| Remedy: | Open the side door; does any paper remain in the paper path from the cassette? Y: Remove the paper. N: Is the width of the side guide set too narrow for the paper width? Y: Set the side guide wider. (When the tray is being lifted, make sure that a gap is left between the paper and the side guide.) N: Is the harness between the LGC board and the cassette feed-jam sensor open-circuited? Is the cassette feed-jam sensor connector or the connector J106 or J107 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the cassette feed-jam sensor. 2. Replace the LGC board. |
| Error code: | E14 |
| Display: | E14-Front Cover B Open |
| Description: | The front cover (Cover B) is open. Close the cover so that printing can continue. |
| Remedy: | 1. Ensure the duplexer is installed correctly. 2. Inspect the connector at the rear end of the duplexer unit. 3. Inspect the wiring harness leading from the duplexer unit interface connector to the engine controller board. 4. Replace the duplexer unit. 5. Replace the engine controller board. |
| Error code: | E15 |
| Description: | Paper misfeed from the 3rd cassette |
| Causes: | • If the light path of the Master tension plate sensor is not blocked within 384 pulse rotation of the Read pulse motor rotated in the reverse direction. • If master loading error is detected at Drum angle 79° and if the Master tension plate sensor is blocked. |
| Remedy: | Open the side door; does any paper remain in the paper path from the cassette? Y: Remove the paper. N: Is the width of the side guide set too narrow for the paper width? Y: Set the side guide wider. (When the tray is being lifted, make sure that a gap is left between the paper and the side guide.) N: Is the harness between the LGC board and the cassette feed-jam sensor open-circuited? Is the cassette feed-jam sensor connector or the connector J106 or J107 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the cassette feed-jam sensor. 2. Replace the LGC board. |
| Error code: | E16 |
| Description: | Paper misfeed from the 4th cassette |
| Causes: | • If excessive current is detected 0.3 seconds consecutively after the Inking motor is activated. |
| Remedy: | Open the side door; does any paper remain in the paper path from the cassette? Y: Remove the paper. N: Is the width of the side guide set too narrow for the paper width? Y: Set the side guide wider. (When the tray is being lifted, make sure that a gap is left between the paper and the side guide.) N: Is the harness between the LGC board and the cassette feed-jam sensor open-circuited? Is the cassette feed-jam sensor connector or the connector J106 or J107 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the cassette feed-jam sensor. 2. Replace the LGC board. |
| Error code: | E19 |
| Description: | Paper misfeed from the LCF |
| Causes: | • If the light path of the TPH pressure sensor is not opened within 10 seconds after the Write pulse motor is activated. [During TPH Down Positioning] • If the light path of the TPH pressure sensor is not blocked within 10 seconds after the Write pulse motor is activated. |
| Remedy: | Open the side door; does any paper remain in the paper path from the LCF? Y: Remove the paper. N: Is the harness between the LGC board and the cassette feed-jam sensor open-circuited? Is the cassette feed-jam sensor connector or the connector J105 or J107 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the cassette feed-jam sensor. 2. Replace the LGC board. |
| Error code: | E20 |
| Description: | Paper fed from the 1st cassette (not reaching the registration sensor) |
| Causes: | • If excessive current is detected 0.3 seconds consecutively after the Paper ejection motor is activated. |
| Remedy: | Open the jam access cover. Is there any paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[4]/[E]) NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Is the 1st cassette feed clutch working? (Perform the output check in the test mode: 03-201) NO 1. Check if the connector of the 1st cassette feed clutch is disconnected. 2. Check if the connector J329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board for short- or open-circuited. 5. Replace the upper cassette feed clutch. 6. Replace the LGC board. YES Check the 1st cassette feed roller and separation roller. Replace them if they are worn out. |
| Error code: | E21 |
| Description: | Paper transport jam from the LCF |
| Remedy: | Open the side door; does any paper remain in the paper path up to the registration roller? Y: Remove the paper. N: Is the harness between the LGC board and the cassette feed-jam sensor open-circuited? Is the harness between the LGC board and the registration sensor open-circuited? Is the cassette feed-jam sensor connector, registration sensor connector, or the connector J107 or J108 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the cassette feed-jam sensor or the registration sensor. 2. Replace the LGC board. |
| Error code: | E22 |
| Description: | Paper transport jam from the 1st cassette |
| Remedy: | Open the side door; does any paper remain in the paper path up to the registration roller? Y: Remove the paper. N: Is the harness between the LGC board and the cassette feed-jam sensor open-circuited? Is the harness between the LGC board and the registration sensor open-circuited? Is the cassette feed-jam sensor connector, registration sensor connector, or the connector J107 or J108 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the cassette feed-jam sensor or the registration sensor. 2. Replace the LGC board. |
| Error code: | E30 |
| Description: | Paper fed from the 3rd cassette (not reaching the registration sensor) |
| Causes: | The Developer Unit is not connected to the machine. |
| Error code: | E31 |
| Description: | Paper fed from the 3rd cassette (not reaching the 1st cassette transport sensor) |
| Remedy: | Open the feed cover. Is there paper in front of the 1st cassette transport sensor? YES Remove the paper. NO Is the 1st cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) NO 1. Check if the connector of the 1st cassette transport sensor is disconnected. 2. Check if the connector J328, 329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-202, 203, 210) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out. |
| Error code: | E32 |
| Description: | Paper fed from the 3rd cassette (not reaching the 2nd cassette transport sensor) |
| Causes: | The Upper Size Selector is having some error. |
| Remedy: | Open the feed cover. Is there paper in front of the 2nd cassette transport sensor? YES Remove the paper. NO Is the 2nd cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[3]/[B]) NO 1. Check if the connector of the 2nd cassette transport sensor is disconnected. 2. Check if the connector J328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 2nd cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-203, 210, 226) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out. |
| Error code: | E33 |
| Description: | Paper fed from the 3rd cassette (not reaching the 3rd cassette transport sensor) |
| Causes: | The Lower Size Selector is having some error. |
| Remedy: | Open the feed cover. Is there any paper in front of the 3rd cassette transport sensor? YES Remove the paper. NO Is the 3rd cassette tranport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[4]/[B] NO 1. Check if the connector of the 3rd cassette transport sensor is disconnected. 2. Check if the connector J328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5 Replace the 3rd cassette transport sensor. 6. Replace the LGC board. YES Is the transport clutch working? (Perform the output check in the test mode: 03-225) NO 1. Check if the connector of the transport clutch is disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5 Replace the transport clutch. 6 Replace the LGC board. YES Check the transport roller. Replace it if it is worn out. |
| Error code: | E34 |
| Description: | Paper fed from the 4th cassette (not reaching the registration sensor) |
| Causes: | The IC1 on the Main PCB is broken or not put into the socket proper. |
| Error code: | E35 |
| Description: | Paper fed from the 4th cassette (not reaching the 1st cassette transport sensor) |
| Causes: | The Fuser Blower 1 (BL1) on the driving side is not working correctly. |
| Remedy: | Open the feed cover. Is there paper in front of the 1st cassette transport sensor? YES Remove the paper. NO Is the 1st cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) NO 1. Check if the connector of the 1st cassette transport sensor is disconnected. 2. Check if the connector J328, 329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-202, 203, 210) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out. |
| Error code: | E36 |
| Description: | Paper fed from the 4th cassette (not reaching the 2nd cassette transport sensor) |
| Causes: | The Paper Feeding Blower (BL3) is not working correctly. |
| Error code: | E3C |
| Description: | Paper fed from the tandem LCF (not reaching the registration sensor) |
| Error code: | E3D |
| Description: | Paper fed from the tandem LCF (not reaching the 1st cassette feed sensor) |
| Remedy: | Open the feed cover. Is there paper in front of the 1st cassette transport sensor? YES Remove the paper. NO Is the 1st cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) NO 1. Check if the connector of the 1st cassette transport sensor is disconnected. 2. Check if the connector J328, 329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-202, 203, 210) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out. |
| Error code: | E3E |
| Description: | Paper fed from the tandem LCF (not reaching the 2nd cassette feed sensor) |
| Remedy: | Open the feed cover. Is there paper in front of the 2nd cassette transport sensor? YES Remove the paper. NO Is the 2nd cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[3]/[B]) NO 1. Check if the connector of the 2nd cassette transport sensor is disconnected. 2. Check if the connector J328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 2nd cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-203, 210, 226) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out. |
| Error code: | E40 |
| Description: | Jam access cover opened during printing |
| Remedy: | Is the jam access cover open? YES Remove paper if there is any, then shut the cover. NO Is the voltage of 24V being supplied from the power supply unit? (Perform the input check in the test mode: 03-[FAX] ON/[1]/[H]) NO 1. Check if the connector for 24V power supply is disconnected. 2. Check if the connector J319 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Replace the LGC board. |
| Error code: | E41 |
| Description: | Front cover opened during printing |
| Remedy: | Is the front cover or the paper-exit unit open? Y: Close the front cover or the paper-exit unit. N: Is the AC harness between the main switch, front cover switch, paper-exit unit switch and switching power supply open-circuited? Is any of the faston terminals (front cover switch, paper-exit unit switch, main switch) and the connector J701 of the switching power supply disconnected? Y: Reconnect the disconnected faston terminal or connector. Replace the harness. N: 1. Replace the front cover switch or the paper-exit unit switch. 2. Replace the main switch. 3. Replace the switching power supply. |
| Error code: | E42 |
| Description: | Side door opened during printing |
| Causes: | The temperature on the side of the Fuser Roller is risen abnormally. |
| Remedy: | Is the side door open? Y: Close the side door. N: Is the harness between the LGC board and the side door open/close switch open-circuited? Is the side door open/close switch connector or the connector J107 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the side door open/close switch. 2. Replace the LGC board. |
| Error code: | E43 |
| Description: | ADU pulled out during printing |
| Remedy: | Is the ADU pushed in securely to the copier? N: Push in the ADU securely to the copier. Y: Is connector J104 on the LGC board disconnected? Is the harness between the LGC board and the ADU drawer connector open-circuited? Y: Reconnect the connector. Replace the harness. N: 1. Replace the LGC board. 2. Replace the ADU. |
| Error code: | E44 |
| Description: | Feed cover opened during printing |
| Remedy: | Is the feed cover open? YES Remove the paper if there is any, then close the cover. NO Is the feed cover sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[4]/[G]) NO 1. Check if the connector of the feed cover sensor is disconnected. 2. Check if the connector J338 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are opencircuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the feed cover sensor. 6. Replace the LGC board. YES Replace the LGC board. |
| Error code: | E45 |
| Description: | LCF jam access cover opened during printing |
| Remedy: | Is the LCF jam access cover open? Y: Close the LCF jam access cover. N: Is the harness between the LGC board and the LCF unit open-circuited? Is the relay connector of the harness between the LGC board and the LCF unit or the connector J105 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the LGC board. 2. Replace the LCF unit. |
| Error code: | E48 |
| Description: | Relay unit opened during printing |
| Remedy: | Is the relay unit open? YES Remove the paper if there is any, then close the unit. NO Is the relay unit opening/closing switch working? (Perform the input check in the test mode: 03-[FAX]ON/[3]/[F]) NO 1. Check if the connector of the relay unit opening/closing switch is disconnected. 2. Check if the connector J315 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the relay unit opening/closing switch. 6. Replace the LGC board. YES Replace the LGC board. |
| Error code: | E51 |
| Description: | Paper not restarting from the ADU stack |
| Remedy: | Is the ADU pushed in securely to the copier? N: Push in the ADU securely to the copier. Y: Is the connector J104 on the LGC board disconnected? Is the harness between the LGC board and the ADU drawer connector open-circuited? Y: Reconnect the connector. Replace the harness. N: 1. Replace the LGC board. 2. Replace the ADU. |
| Error code: | E52 |
| Description: | Paper not reaching the ADU path sensor |
| Remedy: | Is the harness between the LGC board and the ADU path sensor open-circuited? Is the ADU path sensor connector or the connector J123 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the ADU path sensor. 2. Replace the LGC board. |
| Error code: | E55 |
| Description: | Paper remaining on the transport path when CRUN is OFF |
| Remedy: | Open the cover of the unit/area whose picture is flashing on the control panel. Is there any paper on the transport path? YES Remove the paper. NO Is the sensor in the jamming area working? (Perform the input check in the test mode: refer to the following table) NO 1. Check if the connector of the sensor is disconnected. 2. Check if any of the connectors on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the sensor. 6. Replace the LGC board. YES Replace the LGC board. Registration area Registration sensor 03-[ENERGYSAVER]ON/[4][E] Exit/reverse area Exit sensor 03-[ENERGYSAVER]OFF/[6][G] Reversal sensor 1 03-[ENERGYSAVER]OFF/[6][C] Reversal sensor 2 03-[ENERGYSAVER]OFF/[6][B] Reverse transport area Transport sensor 1 03-[ENERGYSAVER]OFF/[0][C] Transport sensor 2 03-[ENERGYSAVER]OFF/[0][A] Transport sensor 3 03-[ENERGYSAVER]OFF/[0][B] Paper feeding area 1st cassette feed sensor 03-[ENERGYSAVER]OFF/[2][A] 2nd cassette feed sensor 03-[ENERGYSAVER]OFF/[3][A] 3rd cassette/Tandem LCF feed sensor 03-[ENERGYSAVER]OFF/[4][A] 4th cassette/Tandem LCF feed sensor 03-[ENERGYSAVER]OFF/[5][A] 1st cassette transport sensor 03-[ENERGYSAVER]OFF/[2][B] 2nd cassette transport sensor 03-[ENERGYSAVER]OFF/[3][B] 3rd cassette/Tandem LCF transport sensor 03-[ENERGYSAVER]OFF/[4][B] 4th cassette/Tandem LCF transport sensor 03-[ENERGYSAVER]OFF/[5][B] |
| Error code: | E71 |
| Display: | E71 PRAM DATA ADDR |
| Description: | Original not reaching the aligning sensor |
| Remedy: | Have too many originals been placed? Y: Reset the originals, following the specification. N: Are the original sheets curled or folded too much? Y: Flatten and reset the originals. N: Are different-size originals placed together? Y: Set only one-size originals. N: Is the gap between the aligning plate and the feed roller too large? Y: Adjust the gap. N: Is the separation pad stained? Y: Clean the separation pad. |
| Error code: | E72 |
| Description: | Original not reaching the exit sensor |
| Remedy: | Have too many originals been placed? Y: Reset the originals, following the specification. N: Are the original sheets curled or folded too much? Y: Flatten and reset the originals. N: Are different-size originals placed together? Y: Set only one-size originals. N: Is the gap between the aligning plate and the feed roller too large? Y: Adjust the gap. N: Is the separation pad stained? Y: Clean the separation pad. |
| Error code: | E73 |
| Description: | Original not passing the exit sensor |
| Remedy: | Have too many originals been placed? Y: Reset the originals, following the specification. N: Are the original sheets curled or folded too much? Y: Flatten and reset the originals. N: Are different-size originals placed together? Y: Set only one-size originals. N: Is the gap between the aligning plate and the feed roller too large? Y: Adjust the gap. N: Is the separation pad stained? Y: Clean the separation pad. |
| Error code: | E74 |
| Display: | E74 TRANS DATA |
| Description: | Original reversing jam |
| Remedy: | Are the read roller and reverse roller dirty? YES Clean the rollers. NO Is the reverse flapper working properly? NO Adjust the reverse solenoid. |
| Error code: | E91 |
| Description: | Leading edge of paper not reaching the relay unit transport sensor-1 |
| Remedy: | Is there any paper remaining inside the relay unit? YES Remove the paper. NO Are the relay unit transport sensors-1 and -2 working? (Perform the input check in the test mode: 03-[FAX] ON/[4][H], [3][E]) NO 1. Check if the connectors of the relay unit transport sensors-1 and -2 are disconnected. 2. Check if the connector J573 of the relay unit is disconnected. 3. Check if the connector J315 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the relay unit transport sensors. 7. Replace the LGC board. YES Is the relay unit gate solenoid working? (Perform the output check in the test mode: 03-232) NO 1. Check if the connector J573 of the relay unit is disconnected. 2. Check if the connector J315 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Replace the relay unit gate solenoid. 5. Replace the LGC board. YES Does the transport roller of the relay unit work when the main motor is rotated? (Perform the output check in the test mode: 03-101/151) NO Check the drive system of the main unit and relay unit. YES Check if the rollers in the relay unit are worn out. |
| Error code: | E92 |
| Display: | E92 h` |
| Description: | Trailing edge of paper not passing the relay unit transport sensor- 1 |
| Remedy: | Is there any paper remaining inside the relay unit? YES Remove the paper. NO Are the relay unit transport sensors-1 and -2 working? (Perform the input check in the test mode: 03-[FAX] ON/[4][H], [3][E]) NO 1. Check if the connectors of the relay unit transport sensors-1 and -2 are disconnected. 2. Check if the connector J573 of the relay unit is disconnected. 3. Check if the connector J315 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the relay unit transport sensors. 7. Replace the LGC board. YES Is the relay unit gate solenoid working? (Perform the output check in the test mode: 03-232) NO 1. Check if the connector J573 of the relay unit is disconnected. 2. Check if the connector J315 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Replace the relay unit gate solenoid. 5. Replace the LGC board. YES Does the transport roller of the relay unit work when the main motor is rotated? (Perform the output check in the test mode: 03-101/151) NO Check the drive system of the main unit and relay unit. YES Check if the rollers in the relay unit are worn out. |
| Error code: | E93 |
| Description: | Leading edge of paper not reaching the relay unit transport sensor-2 |
| Remedy: | Is there any paper remaining inside the relay unit? YES Remove the paper. NO Are the relay unit transport sensors-1 and -2 working? (Perform the input check in the test mode: 03-[FAX] ON/[4][H], [3][E]) NO 1. Check if the connectors of the relay unit transport sensors-1 and -2 are disconnected. 2. Check if the connector J573 of the relay unit is disconnected. 3. Check if the connector J315 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the relay unit transport sensors. 7. Replace the LGC board. YES Is the relay unit gate solenoid working? (Perform the output check in the test mode: 03-232) NO 1. Check if the connector J573 of the relay unit is disconnected. 2. Check if the connector J315 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Replace the relay unit gate solenoid. 5. Replace the LGC board. YES Does the transport roller of the relay unit work when the main motor is rotated? (Perform the output check in the test mode: 03-101/151) NO Check the drive system of the main unit and relay unit. YES Check if the rollers in the relay unit are worn out. |
| Error code: | E94 |
| Description: | Trailing edge of paper not passing the relay unit transport sensor- 2 |
| Remedy: | Is there any paper remaining inside the relay unit? YES Remove the paper. NO Are the relay unit transport sensors-1 and -2 working? (Perform the input check in the test mode: 03-[FAX] ON/[4][H], [3][E]) NO 1. Check if the connectors of the relay unit transport sensors-1 and -2 are disconnected. 2. Check if the connector J573 of the relay unit is disconnected. 3. Check if the connector J315 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the relay unit transport sensors. 7. Replace the LGC board. YES Is the relay unit gate solenoid working? (Perform the output check in the test mode: 03-232) NO 1. Check if the connector J573 of the relay unit is disconnected. 2. Check if the connector J315 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Replace the relay unit gate solenoid. 5. Replace the LGC board. YES Does the transport roller of the relay unit work when the main motor is rotated? (Perform the output check in the test mode: 03-101/151) NO Check the drive system of the main unit and relay unit. YES Check if the rollers in the relay unit are worn out. |
| Error code: | E9F |
| Description: | Punching jam |
| Remedy: | Is there any paper remaining on the transport path in the finisher or copier? Y: Remove the paper. N: Is either of the connectors J1 or J3 on the punch driver PC board disconnected? Is the harness connecting the punch driver PC board and punch home position sensor (PI3P) open-circuited? Y: Connect the connector securely. Replace the harness. N: Is the punch home position sensor working properly? N: 1. Connect the connector of the punch home position sensor securely. 2. Replace the punch home position sensor. Y: Replace the punch driver PC board. |
| Error code: | EA1 |
| Description: | Paper transport delay jam |
| Remedy: | Is there any paper remaining on the transport path in the finisher or copier? Y: Remove the paper. N: Is the connector J17 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) open-circuited? Y: Connect the connector securely. Replace the harness. N: Is the inlet sensor functioning properly? (Does the actuator return normally?) N: 1. Connect the connector of the inlet sensor securely. 2. Attach the actuator if it has come off. 3. Replace the inlet sensor. Y: Replace the finisher controller PC board. |
| Error code: | EA2 |
| Description: | Paper transport stop jam |
| Remedy: | Is there any paper remaining on the transport path in the finisher or copier? Y: Remove the paper. N: Is any of the connectors J17, J24, J9 and J11 on the finisher controller PC board disconnected? Is any of the harnesses connecting between the finisher controller PC board and sensors (inlet sensor (PI1), buffer path inlet paper sensor (PI17), buffer path paper sensor (PI14), stapling tray sensor (PI4) and delivery sensor (PI3)) open-circuited? Y: Connect the connector securely. Replace the harness. N: Are the inlet sensor, buffer path inlet paper sensor, buffer path paper sensor, stapling tray sensor and delivery sensor functioning properly? (Do the actuators return normally?) N: 1. Connect the connectors of the sensors securely. 2. Attach the actuators if they have come off. 3. Replace the sensors. Y: Replace the finisher controller PC board. |
| Error code: | EA3 |
| Description: | Paper remaining inside the finisher at power ON |
| Remedy: | Is there any paper remaining on the transport path in the finisher? Y: Remove the paper. N: Is any of the connectors J17, J24 and J11 on the finisher controller PC board disconnected? Is any of the harnesses connecting between the finisher controller PC board and sensors (inlet sensor (PI1), buffer path inlet paper sensor (PI17), buffer path paper sensor (PI14) and delivery sensor (PI3)) open-circuited? Y: Connect the connector securely. Replace the harness. N: Are the inlet sensor, buffer path inlet paper sensor, buffer path paper sensor and delivery sensor functioning properly? (Do the actuators return normally?) N: 1. Connect the connectors of the sensors securely. 2. Attach the actuators if they have come off. 3. Replace the sensors. Y: Replace the finisher controller PC board. |
| Error code: | EA4 |
| Description: | Finisher front door opened during printing |
| Remedy: | Is there any paper remaining on the transport path in the finisher or copier? Y: Remove the paper. N: Is the finisher connected with the copier? N: Connect the finisher with the copier. Y: Is the connector J12 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and joint sensor (PI15) open-circuited? Y: Connect the connector securely. Replace the harness. N: Is the joint sensor working properly? N: 1. Connect the connector of the joint sensor securely. 2. Replace the joint sensor. Y: Is the door of the finisher closed? N: Close the door. Y: Is the connector J12 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and door opening sensor (PI16) open-circuited? Y: Connect the connector securely. Replace the harness. N: Is the door opening sensor working properly? N: 1. Connect the connector of the door opening sensor securely. 2. Replace the door opening sensor. Y: Is the connector J5 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and door switch (MS1) open-circuited? Y: Connect the connector securely. Replace the harness. N: Is the door switch working properly? N: 1. Connect the connector of the door switch securely. 2. Replace the door switch. Y: Is the connector J5 on the punch driver PC board disconnected? Is the harness connecting between the punch driver PC board and front door switch (MS2P) open-circuited? Y: Connect the connector securely. Replace the harness. N: Is the front door switch working properly? N: 1. Connect the connector of the front door switch securely. 2. Replace the front door switch. Y: Is the problem solved by replacing the punch driver PC board? End N: Replace the finisher controller PC board. |
| Error code: | EA5 |
| Description: | Finisher stapling jam |
| Remedy: | Is there any paper remaining on the transport path in the finisher or copier, or on the stapling tray? Y: Remove the paper. N: Is the jam cleared by taking off the staple cartridge from the finisher and removing the staple sheet slided from the staple case? Y: End N: Is the connector J8 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and staple home position sensor (PI22) open-circuited? Y: Connect the connector securely. Replace the harness. N: Is the staple home position sensor working properly? N: Replace the stapler unit. Y: Replace the finisher controller PC board. |
| Error code: | EA6 |
| Description: | Finisher early arrival jam |
| Remedy: | Is there any paper remaining on the transport path in the finisher or copier? Y: Remove the paper. N: Is the connector J17 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) open-circuited? Y: Connect the connector securely. Replace the harness. N: Is the inlet sensor functioning properly? (Does the actuator return normally?) N: 1. Connect the connector of the inlet sensor securely. 2. Attach the actuator if it has come off. 3. Replace the inlet sensor. Y: Replace the finisher controller PC board. |
| Error code: | EA7 |
| Description: | Stack transport jam before stapling |
| Error code: | EA8 |
| Description: | Saddle stitcher stapling jam |
| Remedy: | Is there any paper remaining on the transport path in the finisher, saddle stitcher section or copier, or on the stapling tray? Y: Remove the paper. N: Is the jam cleared by taking off the staple cartridge from the saddle stitcher and removing the staples stuck in the stapling unit? Y: End N: Is the connector J8 on the saddle stitcher controller PC board disconnected? Is the harness connecting the saddle stitcher controller PC board and stitcher home position switch (rear: MS5S, front: MS7S) open-circuited? Y: Connect the connector securely. Replace the harness. N: Are the stitcher home position switches working properly? N: Replace the stapler unit. Y: Replace the saddle stitcher controller PC board. |
| Error code: | EA9 |
| Description: | Saddle stitcher front door opened during printing |
| Remedy: | Is there any paper remaining on the transport path in the finisher, saddle stitcher section or copier? Y: Remove the paper. N: Is the saddle stitcher door closed? N: Close the door. Y: Is either of the connectors J10 or J11 on saddle stitcher controller PC board disconnected? Is any of the harnesses connecting between the saddle stitcher controller PC board and cover opening sensors (PI2S: front door opening/closing sensor, PI3S: delivery cover sensor, PI9S: inlet cover sensor) open-circuited? Y: Connect the connector securely. Replace the harness. N: Are the cover opening sensors working properly? N: 1. Connect the connectors of the cover opening sensors securely. 2. Replace the cover opening sensors. Y: Replace the saddle stitcher controller PC board. |
| Error code: | EAA |
| Description: | Paper remaining in the saddle stitcher at power ON |
| Remedy: | Is there any paper remaining on the transport path in the finisher or saddle stitcher section? Y: Remove the paper. N: Is any of the connectors J10, J13 and J9 on the saddle stitcher controller PC board disconnected? Is any of the harnesses connecting between the saddle stitcher controller PC board and sensors (No.1 paper sensor (PI18S), No.2 paper sensor (PI19S), No.3 paper sensor (PI20S), vertical path paper sensor (PI17S) and delivery sensor (PI11S)) open-circuited? Y: Connect the connector securely. Replace the harness. N: Are the No.1 paper sensor, No.2 paper sensor, No.3 paper sensor, vertical path paper sensor and delivery sensor functioning properly? (Do the actuators return normally?) N: 1. Connect the connectors of the sensors securely. 2. Attach the actuators if they have come off. 3. Replace the sensors. Y: Replace the saddle stitcher controller PC board. |
| Error code: | EAB |
| Description: | Saddle stitcher transport stop jam |
| Remedy: | Is there any paper remaining on the transport path in the finisher, saddle stitcher section or copier? Y: Remove the paper. N: Is either of the connectors J10 or J9 on the saddle stitcher controller PC board disconnected? Is any of the harnesses connecting between the saddle stitcher controller PC board and sensors (No.1 paper sensor (PI18S), No.2 paper sensor (PI19S), No.3 paper sensor (PI20S) and delivery sensor (PI11S)) open-circuited? Y: Connect the connector securely. Replace the harness. N: Are the No.1 paper sensor, No.2 paper sensor, No.3 paper sensor and delivery sensor functioning properly? (Do the actuators return normally?) N: 1. Connect the connectors of the sensors securely. 2. Attach the actuators if they have come off. 3. Replace the sensors. Y: Replace the saddle stitcher controller PC board. |
| Error code: | EAC |
| Description: | Saddle stitcher transport delay jam |
| Remedy: | Is there any paper remaining on the transport path in the finisher, saddle stitcher section or copier? Y: Remove the paper. N: Is any of the connectors J6, J9 and J10 on the saddle stitcher controller PC board disconnected? Is any of the harnesses connecting between the saddle stitcher controller PC board and the sensors (No.1 paper sensor (PI18S), No.2 paper sensor (PI19S), No.3 paper sensor (PI20S), delivery sensor (PI11S), and paper positioning plate paper sensor (PI8S)) open-circuited? Y: Connect the connector securely. Replace the harness. N: Are the No.1 paper sensor, No.2 paper sensor, No.3 paper sensor, delivery sensor, and paper positioning plate paper sensor functioning properly? (Do the actuators return normally?) N: 1. Connect the connector of the sensor securely. 2. Attach the actuator if it has come off. 3. Replace the sensor. Y: Replace the saddle controller controller PC board. |
| Error code: | EAD |
| Description: | Print end command time-out jam |
| Remedy: | Is the main motor rotating normally? NO 1. Replace the SYS board. 2. Replace the LGC board. |
| Error code: | EAE |
| Description: | Finisher receive time-out jam |
| Remedy: | Is the finisher working? Y: Replace the finisher controller PC board. N: 1. Check if the voltage (24V) is being supplied to the finisher. 2. Check the connection of the LGC board and IPC board. 3. Check if the harness connecting the IPC board and finisher I/F connector of the copier side is open-circuited. 4. Check if the harness connecting the I/F connector of the finisher side and finisher controller PC board is open-circuited. 5. Replace the finisher controller PC board. |
| Error code: | EAF |
| Description: | Stapled stack transport jam |
| Remedy: | MJ-1011 Is there any paper remaining on the transport path in the finisher or main unit? YES Remove the paper. NO Is the connector J10 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and returning roller home position sensor (S3D) open-circuited? YES Connect the connector securely. Replace the harness. NO Is the returning roller home position sensor working properly? NO 1. Connect the connector of the returning roller home position sensor securely. 2. Replace the returning roller home position sensor. YES Replace the finisher controller PC board. |
| Error code: | EB3 |
| Description: | Ready time time-out jam |
| Remedy: | Is there paper in the main unit? NO Replace the LGC board. YES Are the IPC board and LGC board properly connected to each other? NO Connect them properly. YES Is the harness securely connected to the IPC board? NO Connect the harness securely. YES Is any of the connector pins of the harness connecting the PPC and finisher disconnected or any of those harnesses open-circuited? NO Connect the pin securely/replace the harness. YES 1. Replace the IPC board. 2. Replace the LGC board. 3. Replace the finisher controller PC board. |
| Error code: | EB5 |
| Description: | Paper left on the transport path |
| Remedy: | In case an paper is fed from the 1st cassette, bypass feed unit or reversed paper transport section: Open the bypass unit cover. Is there any paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[4]/[E) NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Check the rollers. Replace them if they are worn out. In case an paper is fed from the 2nd, 3rd, 4th or tandem LCF: Open the feed cover. Is there any paper in front of the 1st cassette transport sensor? YES Remove the paper. NO Is the 1st cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) NO 1. Check if the connector of the 1st cassette transport sensor is disconnected. 2. Check if the connector J329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette transport sensor. 6. Replace the LGC board. YES Check the rollers. Replace them if they are worn out. |
| Error code: | EB6 |
| Description: | Paper left on the transport path |
| Remedy: | Open the bypass unit cover. Is there any paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[4]/[E) NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Check the rollers. Replace them if they are worn out. |
| Error code: | F07 |
| Description: | Communications error between system-CPU and LGC-CPU |
| Causes: | 014 The print drum was not centered at the start of master making. |
| Remedy: | Did the error occur immediately after updating the firmware? Y: Are the proper files saved in the PC? (In case of updating by PC) Are the type, attaching position and direction of the ROM correct? (In case of updating by download jig) N: After correcting, perform the firmware updating again. Y: Though the firmware updating was carried out correctly, error occurs.) N: Did the error occur during printing by the printer controller? Y: Turn OFF and ON the power of printer controller. N: 1. Check if the SYC board is securely connected to the MTH1 board. 2. Check if the IMC board is securely connected to the MTH1 board. 3. Check if the IMC board connector J182 is disconnected. 4. Check if the LGC board connector J113 is disconnected. 5. Check if the harness between the IMC and LGC boards is open-circuited. 6. Check the version of FROM on the SYS board. 7. Check the version of MROM on the LGC board. 8. Check the version of IMC-ROM on the IMC board. 9. Replace the SYS board. 10. Replace the IMC board. 11. Replace the LGC board. |
| Error code: | F10 |
| Description: | HDD formatting error |
| Causes: | 021 Paper size does not match with the size of image on the print drum when test print is selected and activated. |
| Remedy: | (1) Format the HDD. (Enter "2" into 08-690) (2) Check if the HDD is mounted. (3) Check if the specified HDD is mounted. (4) Check if the connector pins of the HDD are bent. (5) Check if the power supply connector is disconnected. (6) Check if the connector J144 on the SYS board is disconnected. (7) Replace the HDD. (8) Replace the SYS board. (9) Replace the harness. * When changing a HDD, do the following operations after replacing a new one. 1. Formatting of the HDD <Procedure> (1) Turen ON the power while the digital keys [0] and [8] are pressed simultaneously. (2) Confirm that "Test Mode" is displayed on the control panel. Enter the code "690" and press the [START] key. The display changes to "System Mode". (3) Enter "2" and press the [SET] or [INTERRRUPT] key. (4) [WAIT] is displayed. (5) Turn OFF the power after the message [REBOOT THE MACHINE] is displayed. 2. Downloading of the UI data |
| Error code: | F11 |
| Description: | Communications error between system-CPU and scanner-CPU |
| Causes: | 023 The paper size did not match the image on the print drum at the start of master making, when the paper loaded into the paper-feed tray was changed. |
| Remedy: | Did the error occur immediately after updating the firmware? Y: Are the proper files saved in the PC? (In case of updating by PC) Are the type, attaching position and direction of the ROM correct? (In case of updating by download jig) N: After correcting, perform the firmware updating again. N: 1. Check if the IMG board connector J161 is disconnected. 2. Check if the SCM board connector J1 is disconnected. 3. Check if the harness between the IMG and SCM boards is open-circuited. 4. Check if the IMG board is securely connected to the MTH1 board. 5. Check if the SYS board is securely connected to the MTH1 board. 6. Check the version of FROM on the SYS board. 7. Check the version of FROM on the SCM board. 8. Check the scanner related setting values (08-360 and 361). 9. Replace the SYS board. 10. Replace the IMG board. 11. Replace the SCM board. |
