Toshiba e-Studio 650

Рейтинг

Парткаталог
Коды ошибок

Модули

PM-KIT

COVER-2-ASM

FEED-DRIVE-ASM

FRONT-FRAME-ASM

LASER-OPT-ASM

OPTICAL-FRAME-ASM

ALIGNING-ROLLER-ASM

CLEANER-2-ASM

COVER-ASM

MANUAL-FEED-DRIVE-2-ASM

REAR-FRAME-1-ASM

CHARGER-DRIVE-ASM

PLATEN-ASM

SUPPLIES

RECYCLE AUGER-ASM

FUSER-DRIVE-ASM

PAPER-FEED-ASM

TANDEM-LCF-2-ASM

DEVELOPER-2-ASM

TRANSPORT-BELT-DRIVE-2-ASM

CRG-2-ASM

TRANSPORT-BELT-CASE-2-ASM

FUSER-3-ASM

OPTICAL-ELECTRIC-ASM

TRANSPORT-BELT-DRIVE1

FEED-3-ASM

CLEANER-1-ASM

TRAY-ASM

HINGE-ASM

TONNER-DRIVE-ASM

COVER-1-ASM

REVERSE-DRIVE-ASM

UPPER-FRAME-ASM

FEED-DRIVE-2-ASM

CRG-1-ASM

TRANSPORT-BELT-GUIDE-2

LOWER-FRAME-ASM

DEVELOPER-1-ASM

ELECTRIC-ASM

REVERSE-OPEN-GUIDE-2-ASM

FEED-2-ASM

FEED-DRIVE-1-ASM

TRANSPORT-ROLLER-ASM

CASSETTE-ASM

CLEANER-3-ASM

REVERSE-OPEN-GUIDE-1-A

TRANSPORT-BELT-GUIDE-1

REPLACE UNIT

TANDEM-LCF-1-ASM

CONTROL-PANEL-ASM

FUSER-2-ASM

MAIN-CHARGER-ASM

FEED-1-ASM

LGC & SYS-ASM

MANUAL-TRAY-ASM

OPTICAL-DRIVE-ASM

DRUM DRUM-DRIVE ASM

DEV DRIVE/STAY-ASM

GUIDE-OPEN-ASM

USED-TONER AUGER-ASM

REAR-FRAME-2-ASM

FUSER-1-ASM

MANUAL-FEED-DRIVE-1-ASM

FEED-4-ASM

DEVELOPER-COVER-ASM

FEED-5-ASM

TRANSPORT-BELT-CASE-1-ASM

Детали TONNER-DRIVE-ASM

Деталь:	HOP-SUB-TNR-N
Парткод:	6LA03081000

Деталь:	AUG-HOP-SUB-N
Парткод:	6LA03087000

Деталь:	BUSH-0613-06F-M
Парткод:	6LA02367000

Деталь:	BUSH-HOPPER
Парткод:	6LA03220000

Деталь:	SEAL-SHUTTER-N
Парткод:	6LA03085000

Деталь:	SHUTTER-HOP-N
Парткод:	6LA03083000

Деталь:	SPC-SHT-N
Парткод:	6LA03084000

Деталь:	SEAL-HOPPER-N
Парткод:	6LA03086000

Деталь:	HOLDER-CPL
Парткод:	6LA03101000

Деталь:	COVER-CPL
Парткод:	6LA03102000

Деталь:	SEAL-VR90A
Парткод:	6LA03104000

Деталь:	SEAL-VR14A
Парткод:	6LA03105000

Деталь:	SEAL-WAS-90108
Парткод:	6LA03106000

Деталь:	SEAL-WAS-1426
Парткод:	6LA03107000

Деталь:	GSKT-TNR-DRV
Парткод:	6LA03108000

Деталь:	SM-SSM13F2
Парткод:	E0-05031000

Деталь:	SCREW20D23
Парткод:	44204394000

Деталь:	ASYS-BRKT-DRV-BTL1
Парткод:	6LA03121000

Деталь:	ASYS-BRKT-DRV-BTL2
Парткод:	6LA03123000

Деталь:	GP08S17/2GT072
Парткод:	6LA03236000

Деталь:	BLT/T-244-2GT-3
Парткод:	6LA03146000

Деталь:	GG08S066/10S017
Парткод:	6LA03144000

Деталь:	GG08S036/08S016
Парткод:	6LA03141000

Деталь:	MOTR.D-TNR-340
Парткод:	6LA07124000

Деталь:	GEAR10S047-06
Парткод:	6LA03145000

Деталь:	ASYS-BRKT-DRV-HOP
Парткод:	6LA03125000

Деталь:	GEAR08S018-06
Парткод:	6LA03143000

Деталь:	BUSH-6L
Парткод:	4400802070

Деталь:	GEAR-08S036-06
Парткод:	6LA03140000

Деталь:	HLDR-BOTTLE
Парткод:	6LA03160000

Деталь:	MG-CATCH-44
Парткод:	44200424000

Деталь:	EHP-6U
Парткод:	F0-00339000

Деталь:	HRNS-TNR-HOP-340
Парткод:	6LA07399000

Деталь:	ASYS-BRKT-TNR-U
Парткод:	6LA03161000

Деталь:	BRKT-TNR-U-SUB
Парткод:	6LA03169000

Деталь:	BRKT-TNR-L
Парткод:	6LA03164000

Деталь:	PDL-TNR-DRV-340
Парткод:	6LA03088000

Деталь:	GEAR-08S020-04
Парткод:	6LA03089000

Деталь:	BUSH-0410-05F-M
Парткод:	6LA02920000

Деталь:	STICK-DRV-TNR
Парткод:	6LA06569000

Деталь:	BRKT-TNR-STP
Парткод:	6LA03188000

Деталь:	HLDR-PLGR-BLT
Парткод:	6LA03154000

Деталь:	PLGR-CATCH-BLT
Парткод:	6LA03155000

Деталь:	SPC-CATCH
Парткод:	6LA03153000

Деталь:	COVER-SW-340
Парткод:	6LA03099000

Деталь:	ASYS-WALL-BTL
Парткод:	6LA03190000

Деталь:	COVER-DRV-TNR
Парткод:	6LA03139000

Деталь:	ASYS-COVER-BTL
Парткод:	6LA03286000

Деталь:	HOLDER-WH
Парткод:	4407685930

Деталь:	ASYS-SEAL-SHTR
Парткод:	6LA03225000

Деталь:	RR/E-5-ZC
Парткод:	X0-01266000

Деталь:	S/TPP/HEX-38-NI
Парткод:	6LA08917000

Деталь:	S/TPS/HEX-38-NI
Парткод:	6LA08909000

Деталь:	ASYS-CPL-BTL-U
Парткод:	6LA03177000

Деталь:	ASYS-CPL-BTL-E
Парткод:	6LA03178000

Деталь:	ASYS-CPL-BTL-D
Парткод:	6LA03179000

Деталь:	SEAL-CPL-BTL
Парткод:	6LA03262000

Деталь:	BRKT-SW-340
Парткод:	6LA03098000

Деталь:	SHAFT-TNR-N-OW
Парткод:	6LA03129000

Деталь:	ASYS-G08S050-06
Парткод:	6LA03148000

Коды ошибок

C04

C13

C14

C15

C16

C18

C1A

C1C

C26

C27

C28

C36

C37

C41

C43

C44

C45

C46

C47

C48

C49

C4A

C55

C56

C57

C58

C59

C73

C82

C83

C84

C85

C86

C94

CA1

CA2

CA3

CA5

CA6

CA9

CAA

CAB

CAC

CB1

CB2

CB3

CB4

CB5

CB6

CB7

CB8

CB9

CBA

CBB

CBC

CBD

CBE

CBF

CC0

CC1

CC2

CC4

CC5

CC6

CC7

CCC

CCD

CCE

CD0

CD1

CD2

CD3

CD4

CD5

CE0

CE1

CE2

CE3

CE4

E01

E02

E03

E09

E11

E12

E13

E14

E15

E16

E18

E19

E20

E21

E22

E23

E24

E25

E30

E31

E32

E33

E34

E35

E36

E37

E38

E3C

E3D

E3E

E3F

E41

E44

E45

E46

E47

E50

E51

E52

E54

E55

E57

E58

E59

E5A

E71

E72

E73

E74

E76

E77

E7A

E7B

E7C

E7D

E7E

E7F

E80

E81

E82

E83

E84

E85

E9F

EA1

EA2

EA3

EA4

EA5

EA6

EA7

EA8

EA9

EAA

EAB

EAC

EAD

EAE

EB3

EB5

EB6

EC0

EC1

EC2

EC3

EC4

EC5

EC6

EC7

EC8

EC9

ECA

ECB

ECC

F07

F10

F11

Деталь:	ASYS-MOTR.D-MCH-CL-340
Парткод:	6LA07162000

Error code:	C04
Display:	C04-xxx Add Paper
Description:	Abnormal feed motor
Causes:	402 Paper detection sensor is OFF (not detecting paper).
Remedy:	Is the PFP motor working? (Perform the output check in the test mode: 03-125/175) NO 1. Check if the signal line connector of the feed motor is disconnected. 2. Check if the connector J327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the feed motor board and LGC board are short- or open circuited. 5. Replace the feed motor. 6. Replace the LGC board. YES Is the LED on the feed motor board lit without flashing? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the feed motor board and LGC board are short- or open-circuited. 3. Replace the feed motor. 4. Replace the LGC board. YES Replace the LGC board.

Error code:	C13
Description:	1st cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C14
Description:	2nd cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C15
Description:	3rd cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C16
Description:	4th cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C18
Description:	LCF tray operation abnormal
Remedy:	Is the harness between the LGC board and the LCF unit open-circuited? Is the relay connector of the harness between the LGC board and the LCF unit or the connector J105 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: Are the switches and sensors in the LCF unit working properly? Y: 1. Replace the LCF tray motor. 2. Replace the LGC board. N: 1. Replace the sensors and switches. 2. Replace the LCF drive PC board or the LCF tray-down switch PC board. 3. Replace the LGC board.

Error code:	C1A
Description:	Abnormal tandem LCF end fence motor (Paper can be fed from cassettes other than the tandem LCF cassette.)
Remedy:	Is the LCF end fence motor working? (Perform the output check in the test mode: 03-207) NO 1. Check if the connector of the tandem LCF end fence motor is disconnected. 2. Check if the connector J346 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Are the tandem LCF end fence home/stop position sensors working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[7]/[A], /[7]/[B]) NO 1. Check if the connectors of the sensors are disconnected. 2. Check if the connector J346 on the LGC board is disconnected. 3. Check if the slit reaches the sensors. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the driving mechanism is abnormal. 2. Check if the conductor pattern on the LGC board is short- or open-circuited. 3. Replace the LGC board.

Error code:	C1C
Description:	Abnormal external LCF tray-up motor (Paper can be fed from cassettes other than the external LCF)
Remedy:	Is the tray motor driving? (Perform the output check in the test mode: 03-271) 1. Check if the connector J815 on the LCF tray motor is not disconnected. 2. Check if the connectors J801~804 on the LCF board are not disconnected. 3. Check if the connector of the tray-up sensor is not disconnected. 4. Check if the actuator reaches the sensor. 5. Check if the power (24V) is supplied to 1pin and 2pin of J803. If not, check if the door switch is turned ON and the harness of it is not open-circuited. 6. Replace the LCF board. 7. Replace the LGC board. Is the tray-up sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER] OFF/[1]/[C] 1. Check if the connector of the tray-up sensor is not disconnected. 2. Check if the connectors J801~804 on the LCF board are not disconnected. 3. Check if the actuator reaches the sensor. 4. Check if the coppector pins are not disconnected and the harness is not open-circuited. 5. Replace the LCF board. 6. Replace the LGC board. 1. Check if the tray lifting mechanism has no abnormality. 2. Replace the LCF board. 3. Replace the LGC board.

Error code:	C26
Description:	Peak detection error
Remedy:	Does the exposure lamp light? (Perform the output check in the test mode: 03-267) YES 1. Check if the connectors on the CCD and SLG boards are disconnected. 2. Check if the shading correction plate is dirty. 3. Check if the conductor pattern on the CCD board is short- or open-circuited. 4. Check if the conductor pattern on the SLG board is short- or open-circuited. 5. Replace the lens unit. 6. Replace the SLG board. NO 1. Check if the connectors of the exposure lamp and inverter are disconnected. 2. Check the SLG board if the connector pin J9 is disconnected and the harness is short- or opencircuited. 3. Check if the conductor pattern on the SLG board is short- or open-circuited. 4. Replace the SLG board. 5. Replace the inverter. 6. Replace the exposure lamp.

Деталь:	MO-KIT-8110
Парткод:	6LA06823000

Деталь:	MA-KIT-8110
Парткод:	6LA06825000

Деталь:	FR-KIT-8110
Парткод:	6LA06824000

Деталь:	PM-KIT-8110C
Парткод:	6LA06826000

Error code:	C27
Description:	Carriage home position sensor not turning OFF within a fixed time
Causes:	• If the Master sensor does not find master on the Drum when the Drum is at 79° during the printing movement.
Remedy:	Are the carriages stuck at a point other than the home position? Y: Check the SCM and SDV boards for any abnormal circuit. N: 1. Check if any connector pin is disconnected, or any harness is open- or short-circuited. 2. Check the scan motor drive pulley if its screws are loose. 3. Check if any conductor pattern on the SDV board is open- or short-circuited. 4. Check if any conductor pattern on the SCM board is open- or short-circuited. 5. Replace the SDV board. 6. Replace the SCM board.

Error code:	C36
Description:	Abnormal main charger wire cleaner drive motor
Remedy:	(1) Check if the main charger is not disconnected. (2) Check if the wire cleaner drive motor is driving. (3) Replace the LGC board.

Error code:	C37
Description:	Abnormal transfer belt cam motor
Causes:	• During the Original set movement, if the Original IN sensor does not detect Original (sensor light not reflected) within 1712 pulses after the Read pulse motor activates. • During the Original set movement, if the Original IN sensor stops detecting the Original before the Read pulse motor activates 347 pulses.
Remedy:	(1) Check if the connector of the transfer belt cam motor is not disconnected. (2) Check if the transfer belt contact/release switch is working properly. (3) Replace the transfer belt cam motor. (4) Replace the LGC board.

Error code:	C41
Description:	Thermistor or heater abnormal when warming-up is started
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C43
Description:	Thermistor abnormal during warming-up after abnormality judgment
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C44
Description:	Heater abnormal during warming-up after abnormality judgment
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C45
Description:	Abnormal side thermistor after the copier has become ready
Causes:	MAIN board Switching regulator
Remedy:	1. Check the side thermistor (1) Check if the connector is disconnected. (2) Check if the side thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the side thermistor is open-circuited. 2. Check the LGC board (1) Check if the connector J334 is disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) “6” to “0”.

Error code:	C46
Description:	Heater abnormal (low temperature) after the copier has become ready
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C47
Description:	Rear thermistor abnormal after the copier has become ready
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C48
Description:	Heater abnormal (high temperature)
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.