Toshiba e-Studio 850
Рейтинг
Модули
REVERSE-OPEN-GUIDE-1-ASM
CLEANER-1-ASM
TRANSPORT-BELT-CASE-2-ASM
TRANSPORT-BELT-GUIDE-1-ASM
FUSER-1-ASM
CHARGER-DRIVE-ASM
ELECTRIC-ASM
MANUAL-TRAY-ASM
RECYCLE/AUGER-ASM
SUPPLIES
CLEANER-2-ASM
PM-KIT
TRANSPORT-BELT-DRIVE-2-ASM
FRONT-FRAME-ASM
OPTICAL-DRIVE-ASM
MANUAL-FEED-DRIVE-2-ASM
TANDEM-LCF-1-ASM
LGC-ASM
TONNER-DRIVE-ASM
REAR-FRAME-2-ASM
TRANSPORT-BELT-CASE-1-ASM
FEED-1-ASM
OPTICAL-ELECTRIC-ASM
OPTICAL-FRAME-ASM
DEV DRIVE/STAY-ASM
MAIN-CHARGER-ASM
PAPER-FEED-ASM
COVER-1-ASM
COVER-2-ASM
LOWER-FRAME-ASM
FEED-5-ASM
MANUAL-FEED-DRIVE-1-ASM
USED-TONER/AUGER-ASM
REPLACE UNIT
FUSER-4-ASM
HINGE-ASM
REVERSE-DRIVE-ASM
SYS-ASM
ALIGNING-ROLLER-ASM
FEED-DRIVE-1-ASM
FUSER-3-ASM
UPPER-FRAME-ASM
PLATEN-ASM
LASER-OPT-ASM
REVERSE-OPEN-GUIDE-2-ASM
FEED-3-ASM
DUCT-ASM
FEED-DRIVE-ASM
TRANSPORT-BELT-GUIDE-2-ASM
TRAY-ASM
DRUM/DRUM-DRIVE ASM
FEED-4-ASM
FEED-2-ASM
FUSER-2-ASM
DEVELOPER-2-ASM
TANDEM-LCF-2-ASM
TRANSPORT-BELT-DRIVE-1-ASM
CRG-2-ASM
TRANSPORT-ROLLER-ASM
FUSER-DRIVE-ASM
REAR-FRAME-1-ASM
GUIDE-OPEN-ASM
CONTROL-PANEL-ASM
FEED-DRIVE-2-ASM
DEVELOPER-1-ASM
COVER-ASM
CRG-1-ASM
DRAWER-ASM
CLEANER-3-ASM
Детали TRANSPORT-BELT-DRIVE-1-ASM
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | ROLLER-EXIT-L-390 |
| Парткод: | 6LE03135000 |
| Деталь: | BRG-688ZZNR |
| Парткод: | 4408510800 |
| Деталь: | GEAR-10S019-08 |
| Парткод: | 6LA05664000 |
| Деталь: | K-BRKT-EXIT-U |
| Парткод: | 6LA05652000 |
| Деталь: | GUIDE-REV-O-340 |
| Парткод: | 6LA05682000 |
| Деталь: | ASYS-GUIDE-REV-MID |
| Парткод: | 6LE03115000 |
| Деталь: | GATE-F390 |
| Парткод: | 6LE03113000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | ARM-GATE-F340 |
| Парткод: | 6LA05702000 |
| Деталь: | CUSH-ARM-GATE-390 |
| Парткод: | 6LE05753000 |
| Деталь: | PIN-2-10 |
| Парткод: | 4408256620 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | BRKT-HINGE-OP-L |
| Парткод: | 6LA05744000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | ASY-ROL-EXIT-390 |
| Парткод: | 6LE05754000 |
| Деталь: | SPL-FUS-EX |
| Парткод: | 6LA05658000 |
| Деталь: | ROL-1210 |
| Парткод: | 4406310100 |
| Деталь: | SHAFT-422 |
| Парткод: | 4406310110 |
| Деталь: | ROLLER-IDLE-390 |
| Парткод: | 6LE05723000 |
| Деталь: | BUSH-D6-GCB |
| Парткод: | 4407976990 |
| Деталь: | SPRING-500-ADU |
| Парткод: | 6LA05687000 |
| Деталь: | ASYS-BRKT-HIG-OP-U |
| Парткод: | 6LE03137000 |
| Деталь: | GEAR-10S020-08 |
| Парткод: | 6LA05666000 |
| Деталь: | BRUSH-SUS-E-390 |
| Парткод: | 6LE05752000 |
| Деталь: | ASY-ROL-EXT-U |
| Парткод: | 6LA05760000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | MYLAR-GUIDE-M39 |
| Парткод: | 6LA05696000 |
| Деталь: | MYLAR-GUIDE-M95 |
| Парткод: | 6LA05697000 |
| Деталь: | BRKT-EXIT-U-COV |
| Парткод: | 6LA15757000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | SFT-SCRPR-BRSH |
| Парткод: | 4401904390 |
| Деталь: | SPC-BRSH-CLN |
| Парткод: | 6LA02732000 |
| Деталь: | SEAL-SIDE-CLN-F |
| Парткод: | 6LA02646000 |
| Деталь: | SEAL-SIDE-BLD-F |
| Парткод: | 4401904180 |
| Деталь: | SEAL-SIDE-DRM-F |
| Парткод: | 4406329960 |
| Деталь: | SEAL-CL-REC |
| Парткод: | 6LA02704000 |
| Деталь: | SEAL-SIDE-CLN-R |
| Парткод: | 6LA02669000 |
| Деталь: | SEAL-SIDE-BLD-R |
| Парткод: | 4401904190 |
| Деталь: | SEAL-SIDE-DRM-R |
| Парткод: | 4406329970 |
| Деталь: | SEAL-ROOF-L |
| Парткод: | 4401904860 |
| Деталь: | PLATE-DRM-GAP |
| Парткод: | 6LA02675000 |
| Деталь: | SCREW-DRM-GAP |
| Парткод: | 4406329300 |
| Деталь: | K-COV-GAP-F |
| Парткод: | 6LA02680000 |
| Деталь: | K-PLATE-DRM-GAP |
| Парткод: | 6LA02685000 |
| Деталь: | SPE-050-040-158 |
| Парткод: | 6LA02688000 |
| Деталь: | K-COV-GAP-R |
| Парткод: | 6LA02689000 |
| Деталь: | AUG-CLN-390 |
| Парткод: | 6LE04133000 |
| Деталь: | BASE-NOZZLE-CLN |
| Парткод: | 6LA02700000 |
| Деталь: | SEAL-BASE-NOZ |
| Парткод: | 6LA02701000 |
| Деталь: | SPC-NOZZLE-390 |
| Парткод: | 6LE04126000 |
| Деталь: | SHUTTER-NOZZLE |
| Парткод: | 6LA02703000 |
| Деталь: | BUSH-0613-06F-M |
| Парткод: | 6LA02367000 |
| Деталь: | K-SFT-BRUSH-340 |
| Парткод: | 6LA02711000 |
| Деталь: | PIN-2-10 |
| Парткод: | 4408256620 |
| Деталь: | GEAR-15 |
| Парткод: | 4401904450 |
| Деталь: | K-SEAL-S-REC-F |
| Парткод: | 4406328750 |
| Деталь: | K-SEAL-S-REC-R |
| Парткод: | 4406328760 |
| Деталь: | K-BLADE-REC-300 |
| Парткод: | 4406328620 |
| Деталь: | BUSH-0814-08F-M |
| Парткод: | 6LA02368000 |
| Деталь: | ASYS-VRST-CLN |
| Парткод: | 6LE04128000 |
| Деталь: | GEAR-25 |
| Парткод: | 4401762250 |
| Деталь: | GEAR-23-30 |
| Парткод: | 6LA02719000 |
| Деталь: | PLT-BIAS-BRSH |
| Парткод: | 6LA02713000 |
| Деталь: | WASHER-81403 |
| Парткод: | 4407010320 |
| Деталь: | GEAR-16 |
| Парткод: | 4401904430 |
| Деталь: | B-6000 |
| Парткод: | 6LE19369000 |
| Деталь: | RR/E-6-SS |
| Парткод: | X0-00967000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/HEX-M36-NI |
| Парткод: | 6LA08900000 |
| Деталь: | S/TP/PAN2/S-4X10-NI |
| Парткод: | X0-02052000 |
| Деталь: | S/TPP/HEX-410-NI |
| Парткод: | 6LA08922000 |
| Деталь: | S/TPP/HEX-48-NI |
| Парткод: | 6LA08921000 |
| Деталь: | K-CASE-TRU |
| Парткод: | 4406339350 |
| Деталь: | K-LEVER-CAM |
| Парткод: | 4406339450 |
| Деталь: | ASYS-LVR-HANDLE |
| Парткод: | 6LA02905000 |
| Деталь: | ARM-BELT-TRU |
| Парткод: | 4406339420 |
| Деталь: | HOLDER-ARM-TRU |
| Парткод: | 4406339410 |
| Деталь: | SPC075-080-0315 |
| Парткод: | 6LA08948000 |
| Деталь: | SCRPR-BRUSH-TRU |
| Парткод: | 6LA02918000 |
| Деталь: | BUSH-BRS-F-TRU |
| Парткод: | 4406338940 |
| Деталь: | B-6510TR |
| Парткод: | 6LA23070000 |
| Деталь: | GEAR-08H025-06 |
| Парткод: | 4406338950 |
| Деталь: | BUSH-0612-D6F-M |
| Парткод: | 6LA02922000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | GG08H021/08H031 |
| Парткод: | 4406339300 |
| Деталь: | STOP-RING-8 |
| Парткод: | 4400336190 |
| Деталь: | PLATE-BRS-TRU |
| Парткод: | 4406338960 |
| Деталь: | AUGER-TRU-390 |
| Парткод: | 6LE08800000 |
| Деталь: | BUSH-0410-05F-M |
| Парткод: | 6LA02920000 |
| Деталь: | GEAR-08H028-04 |
| Парткод: | 4406339280 |
| Деталь: | NOZZLE-TRU-IN |
| Парткод: | 4406339230 |
| Деталь: | SEAL-BLADE-TRU-R |
| Парткод: | 6LE08832000 |
| Деталь: | SPC249-100-1220 |
| Парткод: | 4406339690 |
| Деталь: | SHTR-NZL-TRU |
| Парткод: | 4406339510 |
| Деталь: | SEAL-SHTR-TRU |
| Парткод: | 4406339520 |
| Деталь: | NOZZLE-TRU-OUT |
| Парткод: | 4406339240 |
| Деталь: | HLDR-S-NZL-TRU |
| Парткод: | 4406339530 |
| Деталь: | SEAL-NOZZLE-TRU |
| Парткод: | 4406339250 |
| Деталь: | SEAL-F-TRU |
| Парткод: | 4406339390 |
| Деталь: | SEAL-R-TRU |
| Парткод: | 4406339400 |
| Деталь: | SEAL-BLADE-TRU |
| Парткод: | 6LA02917000 |
| Деталь: | BL-6510TR |
| Парткод: | 6LA23075000 |
| Деталь: | K-GUIDE-C-TRU |
| Парткод: | 4406338970 |
| Деталь: | SPL-EARTH-G-C |
| Парткод: | 6LA02919000 |
| Деталь: | SPACER-ARM-TRU |
| Парткод: | 6LA02907000 |
| Деталь: | S/HEX-M48-NI |
| Парткод: | 6LA08905000 |
| Деталь: | S/HEX-M36-NI |
| Парткод: | 6LA08900000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | S/TPP/HEX-410-NI |
| Парткод: | 6LA08922000 |
| Деталь: | BRKT-STAY-OPEN |
| Парткод: | 6LA06228000 |
| Деталь: | PLATE-GUIDE-OP |
| Парткод: | 6LA06225000 |
| Деталь: | SHAFT-LEVER-340 |
| Парткод: | 6LA06226000 |
| Деталь: | SPA057-080-R |
| Парткод: | 4406343100 |
| Деталь: | LEVER-LOCK-GUIDE |
| Парткод: | 6LE03117000 |
| Деталь: | WIRE-GUIDE-OPEN |
| Парткод: | 4406343120 |
| Деталь: | RLR-TRANS-22 |
| Парткод: | 6LA06220000 |
| Деталь: | SPG-E-5R2XR7X47R2 |
| Парткод: | 6LE03139000 |
| Деталь: | MSB-1207 |
| Парткод: | F0-01250000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | RLR-PASS-TR-1 |
| Парткод: | 6LE03403000 |
| Деталь: | RLR-PASS-TR-2 |
| Парткод: | 6LE03114000 |
| Деталь: | PLY/T-3GT025-08 |
| Парткод: | 6LA06337000 |
| Деталь: | BLT/T-366-3GT-4 |
| Парткод: | 6LA06123000 |
| Деталь: | BUSH-8X12X8F |
| Парткод: | 6LA65698000 |
| Деталь: | BUSH-8 |
| Парткод: | 4400802080 |
| Деталь: | CLUCH-G28-08D |
| Парткод: | 6LA15184000 |
| Деталь: | BRKT-SENSOR-TR |
| Парткод: | 6LA06185000 |
| Деталь: | SNSR-FED-390 |
| Парткод: | 6LE09239000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | STOP-RING-6-1.5 |
| Парткод: | 44201801000 |
| Деталь: | BLT/T-303-3GT-4 |
| Парткод: | 6LA06124000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | RR/E-5-ZC |
| Парткод: | X0-01266000 |
| Деталь: | SPACER-DRW-CNCT |
| Парткод: | 6LA14365000 |
| Деталь: | STUD-FUS-REAR |
| Парткод: | 4406324600 |
| Деталь: | BRKT-FUS-EXIT-U |
| Парткод: | 6LA05193000 |
| Деталь: | K-BKT-FUS-F |
| Парткод: | 6LA05208000 |
| Деталь: | BRUSH-FUSER |
| Парткод: | 6LE06670000 |
| Деталь: | K-BRKT-LEV-R |
| Парткод: | 6LA05370000 |
| Деталь: | STUD-FUS-R-G27 |
| Парткод: | 6LA05290000 |
| Деталь: | GEAR-10S027-08 |
| Парткод: | 6LA05264000 |
| Деталь: | STUD-REAR-GEAR |
| Парткод: | 6LA05292000 |
| Деталь: | GG10S029/10S026 |
| Парткод: | 6LA05262000 |
| Деталь: | GG08S028/08S014 |
| Парткод: | 6LA05450000 |
| Деталь: | BRKT-WEB-MOT-390 |
| Парткод: | 6LE06635000 |
| Деталь: | STUD-WEB-MOT |
| Парткод: | 6LA05220000 |
| Деталь: | GG08S035/08S14S |
| Парткод: | 6LA05453000 |
| Деталь: | STUD-WEB-FRM |
| Парткод: | 6LA05221000 |
| Деталь: | MOTR.D-WEB-390 |
| Парткод: | 6LE09234000 |
| Деталь: | BRKT-WEB-SEN-390 |
| Парткод: | 6LE06605000 |
| Деталь: | SHEET-FUS-FRONT |
| Парткод: | 6LA05285000 |
| Деталь: | COVER-FUS-R |
| Парткод: | 6LA05205000 |
| Деталь: | CLUTCH-6-L |
| Парткод: | 4402833110 |
| Деталь: | COVER-FUS-F |
| Парткод: | 6LA05204000 |
| Деталь: | BRKT-IH-F |
| Парткод: | 6LA05200000 |
| Деталь: | SHEET-FUS-FR-L |
| Парткод: | 6LA05287000 |
| Деталь: | S/FPAN-M4X8-NI |
| Парткод: | X0-00486000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | PLWS-1-46B |
| Парткод: | F0-00032000 |
| Деталь: | S/PAN-M4X6-NC |
| Парткод: | X0-01528000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/PAN-M2.6X4-NC |
| Парткод: | X0-01670000 |
| Деталь: | S/TPS/HEX-410-NI |
| Парткод: | 6LA08914000 |
| Деталь: | SCREW-FUSER-M4 |
| Парткод: | 4401759180 |
| Деталь: | TLP1255(C8) |
| Парткод: | C0-10814000 |
| Деталь: | SCREW-CON-DEV-V |
| Парткод: | 6LA08933000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | RAIL-CH-M-L |
| Парткод: | 6LA02250000 |
| Деталь: | RAIL-CH-M-R |
| Парткод: | 6LA02251000 |
| Деталь: | SPL-PRESS-CH-R |
| Парткод: | 4406330570 |
| Деталь: | LEVER-SW |
| Парткод: | 6LA02252000 |
| Деталь: | GEAR-20H |
| Парткод: | 4406330070 |
| Деталь: | ASYS-MOTR-WCLN-390 |
| Парткод: | 6LE04111000 |
| Деталь: | STAY-MOT-CLN |
| Парткод: | 6LA02247000 |
| Деталь: | HOLDER-LAMP-ERS-390 |
| Парткод: | 6LE04118000 |
| Деталь: | LAMP-ERASE-390 |
| Парткод: | 6LE09407000 |
| Деталь: | SSM13F3 |
| Парткод: | E0-05032000 |
| Деталь: | SCREW20D23 |
| Парткод: | 44204394000 |
| Деталь: | HRNS-CLN-390 |
| Парткод: | 6LE09254000 |
| Деталь: | SKB-KI-100M |
| Парткод: | 4400682590 |
| Деталь: | BAND-PS100 |
| Парткод: | 4400902490 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | RR/E-2-SS |
| Парткод: | X0-00963000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/BID-M3X3-NC |
| Парткод: | X0-01951000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | BRKT-AC-UNIT-390 |
| Парткод: | 6LE05404000 |
| Деталь: | BLIND-AC-CABLE |
| Парткод: | 6LA01143000 |
| Деталь: | HRNS-BRK-NF-390 |
| Парткод: | 6LE09268000 |
| Деталь: | SHIELD-PS-ACC-390 |
| Парткод: | 6LE05419000 |
| Деталь: | FL-ZSG2215-11 |
| Парткод: | 6LE09282000 |
| Деталь: | HRNS-FIL-ACMAIN-390 |
| Парткод: | 6LE09267000 |
| Деталь: | HRNS-ACMAIN1-340 |
| Парткод: | 6LA07433000 |
| Деталь: | PWA-F-FIL-390 |
| Парткод: | 6LE09247000 |
| Деталь: | HRNS-INLET-G-390E |
| Парткод: | 6LE09321000 |
| Деталь: | HRNS-INLET-NF-390N |
| Парткод: | 6LE09273000 |
| Деталь: | HRNS-NF-FIL-390 |
| Парткод: | 6LE09262000 |
| Деталь: | HRNS-INLET-BRK-390L |
| Парткод: | 6LE09279000 |
| Деталь: | LWS-2111Z |
| Парткод: | F0-01299000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | S/PAN/SWWP-M4X8-BSNI |
| Парткод: | X0-00169000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | ASYS-P-CABLE-UC |
| Парткод: | 6LA07163000 |
| Деталь: | CBL/P-INLET-EUR |
| Парткод: | 4400395940 |
| Деталь: | VU-220F |
| Парткод: | D0-24625000 |
| Деталь: | NRW10-10A-TK1419 |
| Парткод: | E0-08474000 |
| Деталь: | PS-ACC-390JU |
| Парткод: | 6LE09102000 |
| Деталь: | PS-ACC-390E |
| Парткод: | 6LE09102100 |
| Деталь: | PE7420-1381-091T |
| Парткод: | E0-08478000 |
| Деталь: | SPLSN-6U |
| Парткод: | F0-00342000 |
| Деталь: | NC-179-F6.35 |
| Парткод: | E0-06067000 |
| Деталь: | TRAY-BYPASS-U |
| Парткод: | 6LE03414000 |
| Деталь: | PAD-BRAKE |
| Парткод: | 4400901130 |
| Деталь: | guide-tray-f |
| Парткод: | 6LE03417000 |
| Деталь: | guide-tray-r |
| Парткод: | 6LE03418000 |
| Деталь: | LBL-TRAY-FULL |
| Парткод: | 6LA04795000 |
| Деталь: | k-rack-bypass |
| Парткод: | 4408669700 |
| Деталь: | rack-bypass |
| Парткод: | 4408669710 |
| Деталь: | k-plate-pinion |
| Парткод: | 6LA04788000 |
| Деталь: | PWA-F-SFB-390 |
| Парткод: | 6LE09176000 |
| Деталь: | pinion-18-395 |
| Парткод: | 4407726480 |
| Деталь: | PLATE-GND-BYP |
| Парткод: | 6LA14493000 |
| Деталь: | HRNS-SFB-SIZE-340 |
| Парткод: | 6LA04761000 |
| Деталь: | PIN-TRAY-M-FE |
| Парткод: | 4402814310 |
| Деталь: | SPC-PIN-TRAY-N |
| Парткод: | 6LA08942000 |
| Деталь: | TRAY-BYPASS-M |
| Парткод: | 6LE03416000 |
| Деталь: | ASYS-TRAY-BYP-SUB |
| Парткод: | 6LE03419000 |
| Деталь: | TRAY-BYPASS-L |
| Парткод: | 6LE03415000 |
| Деталь: | S/BID-M3X6-NI |
| Парткод: | X0-00430000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | LBL-TRAY-U |
| Парткод: | 6LA04793000 |
| Деталь: | LBL-TRAY-E |
| Парткод: | 6LA04794000 |
| Деталь: | HOP-SUB-TNR-R |
| Парткод: | 6LA03210000 |
| Деталь: | SEAL-SUB-HOP-R |
| Парткод: | 6LA03212000 |
| Деталь: | AUG-SUB-HOP-R |
| Парткод: | 6LA03213000 |
| Деталь: | GEAR-10S026-06 |
| Парткод: | 6LA03214000 |
| Деталь: | BUSH-HOPPER |
| Парткод: | 6LA03220000 |
| Деталь: | BUSH-0613-06F-M |
| Парткод: | 6LA02367000 |
| Деталь: | SFT-SUB-HOP-N |
| Парткод: | 6LA03215000 |
| Деталь: | PDL-SUB-HOP |
| Парткод: | 6LA03218000 |
| Деталь: | GEAR-10S069-06 |
| Парткод: | 6LA03216000 |
| Деталь: | ASYS-REC-EXIT |
| Парткод: | 6LA03243000 |
| Деталь: | SHUTTER-HOP-R |
| Парткод: | 6LA14474000 |
| Деталь: | SPE-SHT-R |
| Парткод: | 6LA03222000 |
| Деталь: | COV-SUB-TNR-R |
| Парткод: | 6LA03211000 |
| Деталь: | ASYS-BRKT-DRV-R-390 |
| Парткод: | 6LE08558000 |
| Деталь: | MOTRD-AUG-390CW |
| Парткод: | 6LE09546000 |
| Деталь: | BLT/T-190-2GT-4 |
| Парткод: | 6LA03237000 |
| Деталь: | GP08S17/2GT072 |
| Парткод: | 6LA03236000 |
| Деталь: | GG10S016/08S080 |
| Парткод: | 6LA03235000 |
| Деталь: | HRNS-RCY-MOT-390 |
| Парткод: | 6LE09241000 |
| Деталь: | BRKT-RECYCLE |
| Парткод: | 6LA03260000 |
| Деталь: | ASYS-PIPE-195 |
| Парткод: | 6LA03240000 |
| Деталь: | JOIN-CL-NZL-U |
| Парткод: | 6LA03250000 |
| Деталь: | ASYS-JOIN-L |
| Парткод: | 6LA14450000 |
| Деталь: | SEAL-JOIN |
| Парткод: | 6LA03257000 |
| Деталь: | AUG-TNR-R |
| Парткод: | 6LA14448000 |
| Деталь: | WAS-0611Z25-P |
| Парткод: | 4406534410 |
| Деталь: | GEAR-08S022-06 |
| Парткод: | 6LA03255000 |
| Деталь: | HRNS-RCY-MOT2-390 |
| Парткод: | 6LE09261000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | S/PAN-M3X4-NI |
| Парткод: | X0-02113000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | S/PAN-M2.6X2.5-NI |
| Парткод: | X0-02270000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | S/HEX-M48-NI |
| Парткод: | 6LA08905000 |
| Деталь: | LWS-0711Z |
| Парткод: | F0-00736000 |
| Деталь: | D-6000 |
| Парткод: | 6LE19277000 |
| Деталь: | D-6510 |
| Парткод: | 6LA23011000 |
| Деталь: | GM-1050 |
| Парткод: | 6A000000418 |
| Деталь: | GM-4010 |
| Парткод: | 6A000000422 |
| Деталь: | GM-2040 |
| Парткод: | 6A000000420 |
| Деталь: | GP-1060 |
| Парткод: | 6A00000047D |
| Деталь: | GF-1140 |
| Парткод: | 66089914 |
| Деталь: | GN-1040 |
| Парткод: | 6A000000468 |
| Деталь: | GN-2010 |
| Парткод: | 6A000000455 |
| Деталь: | GN-3010 |
| Парткод: | 6A000000459 |
| Деталь: | COVER-ENABLER-390 |
| Парткод: | 6LE04478000 |
| Деталь: | PS-TB6510 |
| Парткод: | 66089851 |
| Деталь: | PS-TB6510E |
| Парткод: | 66089852 |
| Деталь: | PS-ZT6000(4) |
| Парткод: | 6AK00000015 |
| Деталь: | PS-ZT6000(4) |
| Парткод: | 6B000000046 |
| Деталь: | PS-ZT6000E(4) |
| Парткод: | 6AK00000016 |
| Деталь: | PS-ZT6000D(4) |
| Парткод: | 6AK00000017 |
| Деталь: | PS-ZT6000D(4) |
| Парткод: | 6A000000416 |
| Деталь: | MF-6000U |
| Парткод: | 6A000000547 |
| Деталь: | MF-6000E |
| Парткод: | 6A000000548 |
| Деталь: | K-BRKT-BLADE |
| Парткод: | 4401904710 |
| Деталь: | SPACER-BLADE |
| Парткод: | 4401761720 |
| Деталь: | WEIGHT-BLADE-390 |
| Парткод: | 6LE04121000 |
| Деталь: | ASYS-CLAW-DRUM-C |
| Парткод: | 6LE04130000 |
| Деталь: | GUIDE-PAPER-C-C |
| Парткод: | 6LE04131000 |
| Деталь: | SFT-HLDR-BLADE |
| Парткод: | 6LE04122000 |
| Деталь: | SEAL-BLD-U1 |
| Парткод: | 4401904080 |
| Деталь: | SEAL-BLD-U2-148 |
| Парткод: | 4407887150 |
| Деталь: | BL-6000D |
| Парткод: | 6LE19374000 |
| Деталь: | BUSH-BLADE-390 |
| Парткод: | 6LE04102000 |
| Деталь: | CAP-BUSH-BLADE |
| Парткод: | 4401761480 |
| Деталь: | STAY-CLN-F340 |
| Парткод: | 6LA02731000 |
| Деталь: | GUDE-STAY-CLN-390 |
| Парткод: | 6LE04134000 |
| Деталь: | SEAL-STAY-CLN |
| Парткод: | 4406328840 |
| Деталь: | K-ROOF-CLN-300 |
| Парткод: | 4406328590 |
| Деталь: | SFT-CLAW-390 |
| Парткод: | 6LE04132000 |
| Деталь: | LEVER-SFT-CLAW |
| Парткод: | 4406328970 |
| Деталь: | GUIDE-PAPER-C-F |
| Парткод: | 6LA14627000 |
| Деталь: | GUIDE-PAPER-C-R |
| Парткод: | 6LA14628000 |
| Деталь: | K-CLAW-DRUM |
| Парткод: | 6LA15294000 |
| Деталь: | WHEEL-STAR-CLN |
| Парткод: | 4401905970 |
| Деталь: | SCREW-STAR-WH |
| Парткод: | 4401905250 |
| Деталь: | CLT-CAM-CLAW |
| Парткод: | 4401762520 |
| Деталь: | COLLAR-CLT-CLAW |
| Парткод: | 4401762510 |
| Деталь: | SPC-CLAW-SLIDE |
| Парткод: | 6LA02740000 |
| Деталь: | S/PAN-M3X6-ZC |
| Парткод: | X0-00053000 |
| Деталь: | S/HEX-M36-NI |
| Парткод: | 6LA08900000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | S/TPP/PAN-3X6-NI |
| Парткод: | X0-00595000 |
| Деталь: | W/TH/A-4-SS |
| Парткод: | X0-01889000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/TPP/HEX-48-NI |
| Парткод: | 6LA08921000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | S/TPS/PAN-4X32-ZU3 |
| Парткод: | X0-02114000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | MO-KIT-6000 |
| Парткод: | 6LE15200000 |
| Деталь: | MA-KIT-6000 |
| Парткод: | 6LE15221000 |
| Деталь: | FR-KIT-6000 |
| Парткод: | 6LE06677000 |
| Деталь: | PM-KIT-6000C |
| Парткод: | 6LE15201000 |
| Деталь: | PM-KIT-6000 |
| Парткод: | 6LE15202000 |
| Деталь: | ROL-KIT-81CST |
| Парткод: | 6LA06886000 |
| Деталь: | DF-KIT-8110 |
| Парткод: | 6LA09452000 |
| Деталь: | SHAFT-LOCK-HDL |
| Парткод: | 4406337950 |
| Деталь: | SPC089-070-0200 |
| Парткод: | 4406337960 |
| Деталь: | SCREW-STOP-H |
| Парткод: | 4406338130 |
| Деталь: | BRKT-STOP-SFT |
| Парткод: | 4406338420 |
| Деталь: | ACTR-STOP-SFT |
| Парткод: | 4406338400 |
| Деталь: | SCREW-ACTR-TRU |
| Парткод: | 6LA08932000 |
| Деталь: | TERMINAL-TRU |
| Парткод: | 4406337970 |
| Деталь: | PLATE-TERM-TRU1 |
| Парткод: | 4406337980 |
| Деталь: | PLATE-TERM-TRU2 |
| Парткод: | 4406338010 |
| Деталь: | EDS-1717U |
| Парткод: | F0-00047000 |
| Деталь: | PLY/T-3GT25TWIN |
| Парткод: | 4406546980 |
| Деталь: | GEAR10S28-06TWN |
| Парткод: | 4406546990 |
| Деталь: | GEAR-10S028-06 |
| Парткод: | 4406342080 |
| Деталь: | BLT/T-375-3GT-4 |
| Парткод: | 6LA06121000 |
| Деталь: | WAS-06-95-Z13-P |
| Парткод: | 6LA06340000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | CLUCH-G28-08D |
| Парткод: | 6LA15184000 |
| Деталь: | BUSH-8X12X8F |
| Парткод: | 6LA65698000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | MSB-1207 |
| Парткод: | F0-01250000 |
| Деталь: | ASYS-PLT-CPG-TR |
| Парткод: | 6LE08846000 |
| Деталь: | CPG-DRIVE-TRANS |
| Парткод: | 6LA06320000 |
| Деталь: | SHAFT-CPG-TRANS |
| Парткод: | 6LA06325000 |
| Деталь: | BRG-696ZZNR |
| Парткод: | 4407959970 |
| Деталь: | SPC098-080-150 |
| Парткод: | 6LA06330000 |
| Деталь: | BLT/T-249-3GT-4 |
| Парткод: | 6LA06120000 |
| Деталь: | SHAFT-CLH-CPG |
| Парткод: | 6LA14346000 |
| Деталь: | PLY/T-3GT025-08 |
| Парткод: | 6LA06337000 |
| Деталь: | BRKT-CPG-TRS-390 |
| Парткод: | 6LE08843000 |
| Деталь: | HRNS-ADU-390 |
| Парткод: | 6LE09132000 |
| Деталь: | BRKT-CNT-TR-390 |
| Парткод: | 6LE08842000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | P/PRL/AH7-2X10-SS |
| Парткод: | X0-00980000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | RR/E-6-SS |
| Парткод: | X0-00967000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | S/TPS/HEX-412-NI |
| Парткод: | 6LA08915000 |
| Деталь: | BRKT-HINGE-UPR |
| Парткод: | 6LE06335000 |
| Деталь: | BRKT-F/S-UNIT |
| Парткод: | 6LA00950000 |
| Деталь: | BRKT-DOOR-SW-390 |
| Парткод: | 6LE06339000 |
| Деталь: | ASYS-BRKT-HINGE-LWR |
| Парткод: | 6LE06338000 |
| Деталь: | ASYS-BRKT-POS-TRANS |
| Парткод: | 6LE05714000 |
| Деталь: | BRKT-SENS-OPEN |
| Парткод: | 6LA04796000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | STOPPER-KNOB |
| Парткод: | 6LA04151000 |
| Деталь: | SHAFT-GUIDE-OP |
| Парткод: | 4406343710 |
| Деталь: | A8G-109-3-24 |
| Парткод: | E0-08495000 |
| Деталь: | BUSH-DEV |
| Парткод: | 4406333430 |
| Деталь: | HRNS-FRONT-390 |
| Парткод: | 6LE09205000 |
| Деталь: | HRNS-SIDE-390 |
| Парткод: | 6LE09209000 |
| Деталь: | HRNS-MAIN-SW-340 |
| Парткод: | 6LA07461000 |
| Деталь: | LWS-0711Z |
| Парткод: | F0-00736000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | LWS-2111Z |
| Парткод: | F0-01299000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | BD/W-TWS-3027 |
| Парткод: | 4406509170 |
| Деталь: | stud-door-sw |
| Парткод: | 6LA00930000 |
| Деталь: | STOPPER-REAR |
| Парткод: | 4408354010 |
| Деталь: | FA1L-AA22 |
| Парткод: | E0-08442000 |
| Деталь: | GUIDE-SW-DOOR-390 |
| Парткод: | 6LE06329000 |
| Деталь: | ROLL-GUIDE-OPEN |
| Парткод: | 4406343720 |
| Деталь: | BRKT-HOLDER-RLR-390 |
| Парткод: | 6LE06351000 |
| Деталь: | ASYS-LOCK-EXIT-F |
| Парткод: | 6LE03107000 |
| Деталь: | LBL-W-HOT-ANGL |
| Парткод: | 6LA06575000 |
| Деталь: | GUIDE-PUSH-DOOR-390 |
| Парткод: | 6LE06341000 |
| Деталь: | RLWS-1TV0 |
| Парткод: | F0-00367000 |
| Деталь: | P-25 |
| Парткод: | F0-00837000 |
| Деталь: | HOOK-LOCK-EXIT |
| Парткод: | 6LA05785000 |
| Деталь: | HRNS-MAINSW-R-340 |
| Парткод: | 6LA07462000 |
| Деталь: | BRKT-SW-TNR-MAIN |
| Парткод: | 6LE06333000 |
| Деталь: | SCREW20D23 |
| Парткод: | 44204394000 |
| Деталь: | HRNS-FRT-USW-390 |
| Парткод: | 6LE09240000 |
| Деталь: | LWS-4U |
| Парткод: | F0-00026000 |
| Деталь: | STOPPER-KNOB-BYP |
| Парткод: | 6LA15052000 |
| Деталь: | HOLDER-LOCK-CST |
| Парткод: | 6LA04492000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/HEX-M38-NI |
| Парткод: | 6LA08901000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | DE2L-BALG |
| Парткод: | E0-08294000 |
| Деталь: | CS1A-B2CA |
| Парткод: | E0-01853000 |
| Деталь: | HOOK-LOCK-CST |
| Парткод: | 6LA04493000 |
| Деталь: | STUD-LOCK-CST |
| Парткод: | 6LA04494000 |
| Деталь: | SPE080-100-0320 |
| Парткод: | 6LA04495000 |
| Деталь: | SPE075-100-0320 |
| Парткод: | 6LA04851000 |
| Деталь: | SHAFT-DRV-SCAN-390 |
| Парткод: | 6LE08013000 |
| Деталь: | PLY-WIRE-SCAN |
| Парткод: | 6LA01742000 |
| Деталь: | ASYS-WIR-RP-SCAN-FRT-390 |
| Парткод: | 6LE08088000 |
| Деталь: | ASYS-WIR-RP-SCAN-RER-390 |
| Парткод: | 6LE08089000 |
| Деталь: | BRKT-MOT-SCAN |
| Парткод: | 6LA01892000 |
| Деталь: | ASYS-MOTR-SCAN-390 |
| Парткод: | 6LE08046000 |
| Деталь: | BRG-608ZZNR |
| Парткод: | 4407545610 |
| Деталь: | PLY/T-2GT84 |
| Парткод: | 6LA01900000 |
| Деталь: | BLT/T-232-2M-6 |
| Парткод: | 6LA01903000 |
| Деталь: | GLASS-PLATEN |
| Парткод: | 6LA01965000 |
| Деталь: | ASYS-GUIDE-GLASS-390 |
| Парткод: | 6LE08075000 |
| Деталь: | SCREW-ACTR-TRU |
| Парткод: | 6LA08932000 |
| Деталь: | SPE-WIRE-TENS |
| Парткод: | 6LA01754000 |
| Деталь: | PLATE-SHD |
| Парткод: | 6LA01973000 |
| Деталь: | LID-SCREW-390 |
| Парткод: | 6LE08071000 |
| Деталь: | S/PAN/SWWP-M3X8-NI |
| Парткод: | X0-00077000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/TPS/BID-4X8-ZU3 |
| Парткод: | X0-02074000 |
| Деталь: | LBL-SCALE-X-L-390 |
| Парткод: | 6LE08080000 |
| Деталь: | LBL-SCALE-X-A-390 |
| Парткод: | 6LE08078000 |
| Деталь: | LBL-SCALE-Y-L-390 |
| Парткод: | 6LE08081000 |
| Деталь: | LBL-SCALE-Y-A-390 |
| Парткод: | 6LE08079000 |
| Деталь: | K-SHAFT-SEP |
| Парткод: | 6LA04674000 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | GEAR-08-30 |
| Парткод: | 4407906230 |
| Деталь: | ARBOR-16-POM-S |
| Парткод: | 4408307270 |
| Деталь: | GEAR-10S020-06 |
| Парткод: | 4406342070 |
| Деталь: | K-GEAR-08S022-R |
| Парткод: | 6LA04724000 |
| Деталь: | SHAFT-RLR-TRS |
| Парткод: | 6LE03401000 |
| Деталь: | K-RLR-TRS |
| Парткод: | 6LA04665000 |
| Деталь: | PLY/T-S2M-28-08 |
| Парткод: | 6LA04720000 |
| Деталь: | BUSH-8X12X8F |
| Парткод: | 6LA65698000 |
| Деталь: | STOP-RING-8 |
| Парткод: | 4400336190 |
| Деталь: | CLUTCH-G28-08-33F |
| Парткод: | 6LA04768000 |
| Деталь: | BRKT-CLT |
| Парткод: | 6LA04637000 |
| Деталь: | GUIDE-LCF-ENT-L |
| Парткод: | 6LA04661000 |
| Деталь: | ROLLER-IDLE-390 |
| Парткод: | 6LE05723000 |
| Деталь: | BUSH-D6-GCB |
| Парткод: | 4407976990 |
| Деталь: | SPRING-500-ADU |
| Парткод: | 6LA05687000 |
| Деталь: | GUIDE-ROL-TRS-U |
| Парткод: | 6LA04641000 |
| Деталь: | SPCR-GUIDE-ROL |
| Парткод: | 6LA04642000 |
| Деталь: | K-HLDR-TRAY |
| Парткод: | 6LA04631000 |
| Деталь: | STOPPER-TRAY |
| Парткод: | 6LA04790000 |
| Деталь: | KNOB-HINGE |
| Парткод: | 6LA04651000 |
| Деталь: | KNOB-COV-PFP |
| Парткод: | 6LE03422000 |
| Деталь: | SPC-KNOB-STOP |
| Парткод: | 6LA04152000 |
| Деталь: | CUSHION-GUIDE-TRS |
| Парткод: | 6LA04732000 |
| Деталь: | HRNS-SFB-MAIN-390 |
| Парткод: | 6LE09605000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | EDS-1717U |
| Парткод: | F0-00047000 |
| Деталь: | LWS-2111Z |
| Парткод: | F0-01299000 |
| Деталь: | BAND-PS100 |
| Парткод: | 4400902490 |
| Деталь: | SPR-1.0-15.55-S |
| Парткод: | 4406347640 |
| Деталь: | K-ROL-SPT-CW-S |
| Парткод: | 4406347610 |
| Деталь: | COVER-SP-CL |
| Парткод: | 4408307890 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | BRKT-PUSH-F/S |
| Парткод: | 6LA04740000 |
| Деталь: | BUSH-F6-GCB |
| Парткод: | 6LA03977000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | P/PRL/AH7-2X8-SS |
| Парткод: | X0-00979000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | COVER-CSSTT-LWR |
| Парткод: | 6LE04404000 |
| Деталь: | COVER-LCF-LWR |
| Парткод: | 6LE04406000 |
| Деталь: | COVER-LCF-UPR |
| Парткод: | 6LE04405000 |
| Деталь: | LBL-P-SET-390 |
| Парткод: | 6LE03904000 |
| Деталь: | LBL-CST-SET-390 |
| Парткод: | 6LE03903000 |
| Деталь: | FENCE-SIDE-L-F |
| Парткод: | 6LA93726000 |
| Деталь: | FENCE-SIDE-L-R |
| Парткод: | 6LA93728000 |
| Деталь: | SOL-END-340 |
| Парткод: | 6LA15258000 |
| Деталь: | S/TPP/HEX-3X10-NI |
| Парткод: | 6LA08918000 |
| Деталь: | LEVER-TRAY-TNDM |
| Парткод: | 6LA04838000 |
| Деталь: | SPE-030-035-014 |
| Парткод: | 6LA93923000 |
| Деталь: | LWS-2H |
| Парткод: | F0-01397000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | LBL-P-LIMIT |
| Парткод: | 6LA93862000 |
| Деталь: | BRKT-P-SIZE-SZ |
| Парткод: | 6LA04810000 |
| Деталь: | BRKT-FENCE-STOP-N |
| Парткод: | 6LA14833000 |
| Деталь: | SLIDER-E-FENCE |
| Парткод: | 6LA93731000 |
| Деталь: | FENCE-E-TRAY |
| Парткод: | 6LA93730000 |
| Деталь: | BRKT-STOP-BELT |
| Парткод: | 6LA93655000 |
| Деталь: | SHAFT-FENCE-END |
| Парткод: | 6LA04840000 |
| Деталь: | K-BKT-SLIDER-D3 |
| Парткод: | 6LA93661000 |
| Деталь: | PLY-DRIVE-2 |
| Парткод: | 6LA93800000 |
| Деталь: | BLT.SY-591-3GT |
| Парткод: | 6LA04839000 |
| Деталь: | PLY-DRIVE-1 |
| Парткод: | 6LA93799000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | BRKT-SLIDER-D2 |
| Парткод: | 6LA93660000 |
| Деталь: | SFT-SLID-DRV |
| Парткод: | 6LA04813000 |
| Деталь: | SCREW-SEP-ADD |
| Парткод: | 6LE69955000 |
| Деталь: | SIZE-CST-390-E |
| Парткод: | 6LE03709000 |
| Деталь: | STAY-BRKT-FENCE-BASE |
| Парткод: | 6LA14779000 |
| Деталь: | STAY-BRKT-FENCE |
| Парткод: | 6LA14780000 |
| Деталь: | BRKT-FENCE-SENS |
| Парткод: | 6LA14820000 |
| Деталь: | S/PAN/SWWP-M4X8-NI |
| Парткод: | X0-00164000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | S/CTS-M3X6-NI |
| Парткод: | X0-00317000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | BRKT-FIN-CABLE |
| Парткод: | 6LA01296000 |
| Деталь: | BLIND-FIN-CABLE |
| Парткод: | 6LA01294000 |
| Деталь: | COVER-LGC-390 |
| Парткод: | 6LE05401000 |
| Деталь: | PS-HVT-390-M |
| Парткод: | 6LE09307000 |
| Деталь: | ASY-LGC-390S |
| Парткод: | 6LE09570000 |
| Деталь: | ASY-LGC-391S |
| Парткод: | 6LE09570100 |
| Деталь: | ASY-LGC-392S |
| Парткод: | 6LE09570200 |
| Деталь: | ASY-LGC-393S |
| Парткод: | 6LE09570300 |
| Деталь: | LWS-2111Z |
| Парткод: | F0-01299000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | SPS-3U |
| Парткод: | F0-00027000 |
| Деталь: | EDS-2323U |
| Парткод: | F0-00034000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | EDS-1717U |
| Парткод: | F0-00047000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | SCREW40X08-T-ZU3 |
| Парткод: | 6LE04445000 |
| Деталь: | HOP-SUB-TNR-390 |
| Парткод: | 6LE08502000 |
| Деталь: | AUG-HOP-SUB-N |
| Парткод: | 6LA03087000 |
| Деталь: | BUSH-0613-06F-M |
| Парткод: | 6LA02367000 |
| Деталь: | BUSH-HOPPER |
| Парткод: | 6LA03220000 |
| Деталь: | SEAL-SHUTTER-N |
| Парткод: | 6LA03085000 |
| Деталь: | SHUTTER-HOP-N |
| Парткод: | 6LA03083000 |
| Деталь: | SPC-SHT-N |
| Парткод: | 6LA03084000 |
| Деталь: | SEAL-HOPPER-N-390 |
| Парткод: | 6LE08578000 |
| Деталь: | HOLDER-CPL-390 |
| Парткод: | 6LE08503000 |
| Деталь: | COVER-CPL-390 |
| Парткод: | 6LE08540000 |
| Деталь: | ASYS-BKT-MOT-AUG |
| Парткод: | 6LE08517000 |
| Деталь: | SEAL-VR90A |
| Парткод: | 6LA03104000 |
| Деталь: | SEAL-VR14A |
| Парткод: | 44204479000 |
| Деталь: | SEAL-WAS-90108 |
| Парткод: | 6LA03106000 |
| Деталь: | SEAL-WAS-1426 |
| Парткод: | 6LA03107000 |
| Деталь: | GSKT-TNR-DRV |
| Парткод: | 6LA03108000 |
| Деталь: | SSM13F3 |
| Парткод: | E0-05032000 |
| Деталь: | SCREW20D23 |
| Парткод: | 44204394000 |
| Деталь: | BRKT-SW-340 |
| Парткод: | 6LA03098000 |
| Деталь: | ASYS-BKT-DR-BTL1-390 |
| Парткод: | 6LE08508000 |
| Деталь: | ASYS-BKT-DR-BTL2-390 |
| Парткод: | 6LE08511000 |
| Деталь: | GP08S17/2GT072 |
| Парткод: | 6LA03236000 |
| Деталь: | BLT/T-244-2GT-3 |
| Парткод: | 6LA03146000 |
| Деталь: | GG08S066/10S017/08S018 |
| Парткод: | 6LE08554000 |
| Деталь: | MOTRD-AUG-390CW |
| Парткод: | 6LE09546000 |
| Деталь: | MOTRD-TNR-390 |
| Парткод: | 6LE09159000 |
| Деталь: | GEAR10S047-06 |
| Парткод: | 6LA03145000 |
| Деталь: | MYLAR-CPL |
| Парткод: | 6LE08583000 |
| Деталь: | GG08S043/08S017 |
| Парткод: | 6LE08522000 |
| Деталь: | GG08S044/08S017 |
| Парткод: | 6LE08523000 |
| Деталь: | GP08S018/2GT058 |
| Парткод: | 6LE08521000 |
| Деталь: | BLT/T-154-2GT-4 |
| Парткод: | 6LA04627000 |
| Деталь: | GEAR-08S036-06 |
| Парткод: | 6LA03140000 |
| Деталь: | HLDR-BOTTLE-390 |
| Парткод: | 6LE08524000 |
| Деталь: | MG-CATCH-44 |
| Парткод: | 6LE04463000 |
| Деталь: | HRNS-TNR-HOP2-390 |
| Парткод: | 6LE09555000 |
| Деталь: | HRNS-TNR-HOP1-390 |
| Парткод: | 6LE09554000 |
| Деталь: | ASYS-BKT-TNR-U-390 |
| Парткод: | 6LE08533000 |
| Деталь: | BRKT-TNR-U-SUB-390 |
| Парткод: | 6LE08528000 |
| Деталь: | BRKT-TNR-L-390 |
| Парткод: | 6LE08529000 |
| Деталь: | STICK-DRV-TNR-390 |
| Парткод: | 6LE08565000 |
| Деталь: | PDL-TNR-DRV-SUB |
| Парткод: | 6LE08541000 |
| Деталь: | GEAR-08S020-04 |
| Парткод: | 6LA03089000 |
| Деталь: | BUSH-0410-05F-M |
| Парткод: | 6LA02920000 |
| Деталь: | ASYS-COVER-BTL-390 |
| Парткод: | 6LE08567000 |
| Деталь: | COVER-SW-390 |
| Парткод: | 6LE08580000 |
| Деталь: | COV-HLDR-BTL |
| Парткод: | 6LE08525000 |
| Деталь: | LBL-O-ALI-TNR-390 |
| Парткод: | 6LE13138000 |
| Деталь: | BRKT-CLN-SENS |
| Парткод: | 6LE08555000 |
| Деталь: | ASYS-PDL-SENS |
| Парткод: | 6LE08569000 |
| Деталь: | GEAR-08S20-7 |
| Парткод: | 6LE08568000 |
| Деталь: | GEAR-08S50-5 |
| Парткод: | 6LE08556000 |
| Деталь: | HRNS-TNRHOP-MOT-390 |
| Парткод: | 6LE09256000 |
| Деталь: | TSP15D10C-01 |
| Парткод: | C0-10817000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | HLDR-PLGR-BTL-390 |
| Парткод: | 6LE08534000 |
| Деталь: | PLGR-CATCH-BLT |
| Парткод: | 6LA03155000 |
| Деталь: | SPC-CATCH |
| Парткод: | 6LA03153000 |
| Деталь: | ASYS-BRKT-TNR-N-390 |
| Парткод: | 6LE08561000 |
| Деталь: | COVER-DRV-TNR-390 |
| Парткод: | 6LE04424000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | BRKT-TNR-STP |
| Парткод: | 6LA03188000 |
| Деталь: | S/HEX-M48-NI |
| Парткод: | 6LA08905000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | ASYS-CPL-BTL-390U |
| Парткод: | 6LE08587000 |
| Деталь: | ASYS-CPL-BTL-390E |
| Парткод: | 6LE08587200 |
| Деталь: | ASYS-CPL-BTL-390D |
| Парткод: | 6LE08587300 |
| Деталь: | BRKT-DRV-SUB |
| Парткод: | 6LE06334000 |
| Деталь: | TERM-BIAS-SUB |
| Парткод: | 4406333770 |
| Деталь: | PLT-TERMINAL-R1 |
| Парткод: | 4402308980 |
| Деталь: | SPC055-050-0200 |
| Парткод: | 4402308950 |
| Деталь: | SPE060-050-184 |
| Парткод: | 4406333780 |
| Деталь: | SCREW-CH-M |
| Парткод: | 4401905040 |
| Деталь: | PLT-TERMINAL-R2 |
| Парткод: | 4402308970 |
| Деталь: | TERMINAL-FRAME |
| Парткод: | 4406330810 |
| Деталь: | LINK-SND-CLN |
| Парткод: | 4408311350 |
| Деталь: | BAND-PS100 |
| Парткод: | 4400902490 |
| Деталь: | ASYS-BRKT-MOT-CLN-390 |
| Парткод: | 6LE04116000 |
| Деталь: | MOTRD-AUG-390CCW |
| Парткод: | 6LE09545000 |
| Деталь: | GEAR-25-F |
| Парткод: | 4401760590 |
| Деталь: | K-GEAR15-PLY53 |
| Парткод: | 4406329770 |
| Деталь: | BLT/T-2GT156-60 |
| Парткод: | 4406329800 |
| Деталь: | GEAR15-55 |
| Парткод: | 4406329780 |
| Деталь: | SOL-SCRP-340 |
| Парткод: | 6LA15256000 |
| Деталь: | LEVER-CLAW-1 |
| Парткод: | 6LA02238000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | BUSH-DEV |
| Парткод: | 4406333430 |
| Деталь: | TERM-FRAME-TRU |
| Парткод: | 4406340260 |
| Деталь: | BRKT-CNT-R-340 |
| Парткод: | 6LA06405000 |
| Деталь: | HRNS-LGC-ADU-390 |
| Парткод: | 6LE09191000 |
| Деталь: | SCREW-SOCKET |
| Парткод: | 4406343540 |
| Деталь: | K-BRKT-HIG-EX-U |
| Парткод: | 6LA05752000 |
| Деталь: | OCB-875 |
| Парткод: | F0-00019000 |
| Деталь: | HRNS-FUR-MOT-390 |
| Парткод: | 6LE09270000 |
| Деталь: | DETECTOR-DEV-390 |
| Парткод: | 6LE04520000 |
| Деталь: | BLIND-KEY-CTR-390 |
| Парткод: | 6LE06344000 |
| Деталь: | SPC055-050-0230 |
| Парткод: | 6LA03023000 |
| Деталь: | SPC074-070-0145 |
| Парткод: | 6LA08950000 |
| Деталь: | S/PAN/SWWS-M2.6X4-NI |
| Парткод: | X0-02254000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/HEX-M38-NI |
| Парткод: | 6LA08901000 |
| Деталь: | S/TPP/HEX-48-NI |
| Парткод: | 6LA08921000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/HEX-M36-NI |
| Парткод: | 6LA08900000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | HRNS-LGC-TLCF-390 |
| Парткод: | 6LE09488000 |
| Деталь: | BRKT-DRW |
| Парткод: | 6LA93647000 |
| Деталь: | SCREW-CON |
| Парткод: | 6LA93902000 |
| Деталь: | SPC-DRAW |
| Парткод: | 6LA04817000 |
| Деталь: | SCREW-DRW-CON |
| Парткод: | 6LA93890000 |
| Деталь: | MDC-TRAY-UP |
| Парткод: | 6LE09162000 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 6LA08931000 |
| Деталь: | ASYS-HSG-R-TRU-390 |
| Парткод: | 6LE08823000 |
| Деталь: | K-ROL-IDEL-340-TRU |
| Парткод: | 6LA15088000 |
| Деталь: | CAP-IDLE-TRU |
| Парткод: | 6LA02969000 |
| Деталь: | BRKT-BRG-R-TRU |
| Парткод: | 6LA02821000 |
| Деталь: | CLIP-RING-8 |
| Парткод: | 4406338760 |
| Деталь: | RLR-SUPPORT-TRU |
| Парткод: | 6LE08829000 |
| Деталь: | DDLF-840ZZHPOP25LY349 |
| Парткод: | F0-01378000 |
| Деталь: | PLATE-BIAS-TRU-390 |
| Парткод: | 6LE08820000 |
| Деталь: | ASYS-ROL-DRV-TRU |
| Парткод: | 6LE08824000 |
| Деталь: | BUSH-ROL-D-TRU |
| Парткод: | 6LA02974000 |
| Деталь: | PLATE-RLR-DRIVE |
| Парткод: | 4406338640 |
| Деталь: | STOPPER-REAR |
| Парткод: | 4408354010 |
| Деталь: | GEAR-08-H021-08 |
| Парткод: | 4406338650 |
| Деталь: | BRG-608ZZNR-KS |
| Парткод: | 6LA02820000 |
| Деталь: | RLR-GUIDE-JOINT |
| Парткод: | 4406338660 |
| Деталь: | GEAR-10H024-08 |
| Парткод: | 4406338770 |
| Деталь: | STOP-RING-8 |
| Парткод: | 4400336190 |
| Деталь: | BT-6510TR |
| Парткод: | 6LA23065000 |
| Деталь: | ASYS-VRST-510 |
| Парткод: | 6LE04129000 |
| Деталь: | SPG-F-EARTH-TRU |
| Парткод: | 6LE08826000 |
| Деталь: | S/HEX-M38-NI |
| Парткод: | 6LA08901000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/HEX-M48-NI |
| Парткод: | 6LA08905000 |
| Деталь: | WH-FEED-SNS-551 |
| Парткод: | 6LA09155000 |
| Деталь: | BLT-118-S2M-4 |
| Парткод: | 6LA09042000 |
| Деталь: | HOLDER--BH-JOINT |
| Парткод: | 6LA09058000 |
| Деталь: | BRKT-FEED-PICK |
| Парткод: | 6LA09258000 |
| Деталь: | BUSH6 |
| Парткод: | 6LA09062000 |
| Деталь: | CLIP4 |
| Парткод: | 6LA09074000 |
| Деталь: | CLIP5 |
| Парткод: | 6LA09057000 |
| Деталь: | BRKT-FEED-UPPER |
| Парткод: | 6LA09256000 |
| Деталь: | CLIP-3KL |
| Парткод: | 6LA09052000 |
| Деталь: | LVR-EMP |
| Парткод: | 6LA09171000 |
| Деталь: | MIRROR-1005 |
| Парткод: | 6LA09351000 |
| Деталь: | MYLAR-PICK |
| Парткод: | 6LA09402000 |
| Деталь: | PLT-FEED-PICK-D |
| Парткод: | 6LA09263000 |
| Деталь: | PLT-FEED-PIC-SP |
| Парткод: | 6LA09304000 |
| Деталь: | PLT-FED-PICK-SB |
| Парткод: | 6LA09204000 |
| Деталь: | PLT-FEED-SNS-CV |
| Парткод: | 6LA09297000 |
| Деталь: | PLT-K-UPPER |
| Парткод: | 6LE04807000 |
| Деталь: | ROL-BELT-PICK |
| Парткод: | 6LA09003000 |
| Деталь: | FEED-ROLLER |
| Парткод: | 6LA09004000 |
| Деталь: | SFT-FEED |
| Парткод: | 6LA09310000 |
| Деталь: | SFT-FEED-PICK |
| Парткод: | 6LA09309000 |
| Деталь: | SFT-FEED-PICK-D |
| Парткод: | 6LA09313000 |
| Деталь: | SFT-FEED-PIC-SB |
| Парткод: | 6LA09336000 |
| Деталь: | CUSH-POLON4 |
| Парткод: | 6LA09407000 |
| Деталь: | SPL-FEED-EMP |
| Парткод: | 6LA09356000 |
| Деталь: | STAY-FEED-UPPER |
| Парткод: | 6LA09305000 |
| Деталь: | SNS-TLP1241 |
| Парткод: | 6LE00883000 |
| Деталь: | WICK-FEED-P-SUB |
| Парткод: | 6LA09252000 |
| Деталь: | WICK-PICK-OW |
| Парткод: | 6LA09408000 |
| Деталь: | PLY/T-18 |
| Парткод: | 6LA09051000 |
| Деталь: | SHEET-K-UD |
| Парткод: | 6LA09386000 |
| Деталь: | ERR030SK |
| Парткод: | 6LA09032000 |
| Деталь: | ERR050SK |
| Парткод: | 6LA09034000 |
| Деталь: | SCRW-M3-3.2 |
| Парткод: | 6LA09434000 |
| Деталь: | SCR-M3X6ITSR-NI |
| Парткод: | 6LA09396000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA09399000 |
| Деталь: | SCRW-030060FNWS |
| Парткод: | 6LA09010000 |
| Деталь: | BUSH-06 |
| Парткод: | 6LA09017000 |
| Деталь: | WPIN20/08FPA |
| Парткод: | 6LA09435000 |
| Деталь: | BUSH-06 |
| Парткод: | 6LA09006000 |
| Деталь: | ASY-SLG-390S |
| Парткод: | 6LE09597000 |
| Деталь: | HRNS-SLG-SYS-390 |
| Парткод: | 6LE09224000 |
| Деталь: | HRNS-SLG-SPLY-390 |
| Парткод: | 6LE09216000 |
| Деталь: | HRNS-SCN-MOT-390 |
| Парткод: | 6LE09217000 |
| Деталь: | HRNS-DF-390 |
| Парткод: | 6LE09213000 |
| Деталь: | HRNS-SNSR-390 |
| Парткод: | 6LE09211000 |
| Деталь: | SNSR-PS-TY1CH97 |
| Парткод: | 6LE09480000 |
| Деталь: | HRNS-APS-L-390 |
| Парткод: | 6LE09215000 |
| Деталь: | HRNS-APS-A-390 |
| Парткод: | 6LE09214000 |
| Деталь: | ASY-D/H-SCN-BASE-390U |
| Парткод: | 6LE08097000 |
| Деталь: | ASY-D/H-SCN-BASE-390E |
| Парткод: | 6LE08098000 |
| Деталь: | ASY-D/H-SCN-LENS-390U |
| Парткод: | 6LE08103000 |
| Деталь: | ASY-D/H-SCN-LENS-390E |
| Парткод: | 6LE08104000 |
| Деталь: | LENS-UNIT-390 |
| Парткод: | 6LE08099000 |
| Деталь: | ASYS-GLASS-ADF |
| Парткод: | 6LA01979000 |
| Деталь: | ASYS-STY-L-SCN |
| Парткод: | 6LA02010000 |
| Деталь: | BKT-APS-B5R |
| Парткод: | 6LA01870000 |
| Деталь: | COVER-LENS-390 |
| Парткод: | 6LE08057000 |
| Деталь: | COVER-SNSR-LIFT |
| Парткод: | 6LA29902000 |
| Деталь: | CUSH-GLASS |
| Парткод: | 44202810000 |
| Деталь: | CUSH-GLS-ADF340 |
| Парткод: | 6LA01982000 |
| Деталь: | FAND-6015-390 |
| Парткод: | 6LE09167000 |
| Деталь: | HRNS-CCD-390 |
| Парткод: | 6LE09223000 |
| Деталь: | HRNS-SCN-FAN-390 |
| Парткод: | 6LE09225000 |
| Деталь: | SEAL-APS-390 |
| Парткод: | 6LE08036000 |
| Деталь: | SNSR-PS-TY1CH56 |
| Парткод: | 6LE09478000 |
| Деталь: | spl-glas-adf |
| Парткод: | 44202867000 |
| Деталь: | STAY-TOP-R-SCN-390 |
| Парткод: | 6LE08010000 |
| Деталь: | MYLAR-HRNS-INV |
| Парткод: | 6LA39577000 |
| Деталь: | clp-wire-press |
| Парткод: | 4406319330 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | S/PAN/SWWP-M3X20-NI |
| Парткод: | X0-00130000 |
| Деталь: | S/PAN/SWWP-M3X8-NI |
| Парткод: | X0-00077000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | EMT-4N |
| Парткод: | F0-00119000 |
| Деталь: | EMT-5N |
| Парткод: | F0-00362000 |
| Деталь: | BKT-SET-DEV-300 |
| Парткод: | 4406333940 |
| Деталь: | PUSHER-GUIDE |
| Парткод: | 4406333930 |
| Деталь: | HOLDER-PUSHER |
| Парткод: | 4402203810 |
| Деталь: | PUSHER-DEV |
| Парткод: | 4402203800 |
| Деталь: | SPC057-090-0210 |
| Парткод: | 6LA08947000 |
| Деталь: | LEV-SET-DEV-340 |
| Парткод: | 6LA02482000 |
| Деталь: | PIN-BKT-CON-H |
| Парткод: | 6LA08930000 |
| Деталь: | SPL-SET-DEV |
| Парткод: | 4401767560 |
| Деталь: | INS-ENT-DRM-85 |
| Парткод: | 4408847750 |
| Деталь: | K-BKT-BRS-RGT-340-U |
| Парткод: | 6LA15093000 |
| Деталь: | MYLAR-STAY-DEV |
| Парткод: | 4406333950 |
| Деталь: | FAND-6015-390 |
| Парткод: | 6LE09167000 |
| Деталь: | BRKT-FAN-DUCT |
| Парткод: | 6LA02485000 |
| Деталь: | BRKT-STUD-L |
| Парткод: | 6LA03181000 |
| Деталь: | STUD-TNR-L |
| Парткод: | 6LA03182000 |
| Деталь: | SPC-TNR-L |
| Парткод: | 6LA03183000 |
| Деталь: | K-BRKT-DRV-DEV |
| Парткод: | 4406333610 |
| Деталь: | K-GP48-3GT25 |
| Парткод: | 4406333680 |
| Деталь: | K-GP25-3GT25 |
| Парткод: | 4406333690 |
| Деталь: | BLT/T-195-3GT-9 |
| Парткод: | 4406333670 |
| Деталь: | MOTRD-DEV-390 |
| Парткод: | 6LE09160000 |
| Деталь: | BOX-FILTER-FAN-390 |
| Парткод: | 6LE06330000 |
| Деталь: | FILTER-DEV-F300 |
| Парткод: | 4406334920 |
| Деталь: | FAND-DEV-390 |
| Парткод: | 6LE09187000 |
| Деталь: | PLT-NUT-FAN-390 |
| Парткод: | 6LE04527000 |
| Деталь: | K-DUCT-DEV |
| Парткод: | 6LA02510000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | WALL-MOT-DEV |
| Парткод: | 6LA01079000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/HEX-M48-NI |
| Парткод: | 6LA08905000 |
| Деталь: | S/TPS/PAN-4X20-ZU3 |
| Парткод: | X0-02067000 |
| Деталь: | RR/E-6-SS |
| Парткод: | X0-00967000 |
| Деталь: | S/TPS/PAN-3X16-ZU3 |
| Парткод: | X0-02060000 |
| Деталь: | S/TPS/HEX-410-NI |
| Парткод: | 6LA08914000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/BID-M4X40-NC |
| Парткод: | X0-01736000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | CASE-CH-M |
| Парткод: | 6LA02255000 |
| Деталь: | K-GUIDE-CH-L |
| Парткод: | 6LA02295000 |
| Деталь: | TERMINAL-M-F |
| Парткод: | 6LA02258000 |
| Деталь: | TERMINAL-M-R |
| Парткод: | 6LA02297000 |
| Деталь: | SPL-PRESS-CH-F |
| Парткод: | 6LA02291000 |
| Деталь: | FLANGE-10-3-1.5 |
| Парткод: | 4408303080 |
| Деталь: | GEAR-PLY-24-12 |
| Парткод: | 4406330290 |
| Деталь: | BASE-CLN-CH-M |
| Парткод: | 6LA02292000 |
| Деталь: | K-BASE-PAD-CH-M |
| Парткод: | 6LA02274000 |
| Деталь: | HLDR-BASE-PAD |
| Парткод: | 6LA02276000 |
| Деталь: | RENY/PH3-6 |
| Парткод: | F0-00050000 |
| Деталь: | BASE-CLN-CH |
| Парткод: | 6LA02277000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | BELT-2M-800-2 |
| Парткод: | 4401763820 |
| Деталь: | PUSHER-SW-M |
| Парткод: | 6LA02278000 |
| Деталь: | K-BRKT-PLY-I-M |
| Парткод: | 4406330300 |
| Деталь: | SCREW-LOCK-ARM |
| Парткод: | 6LE69956000 |
| Деталь: | BRKT-PLUG |
| Парткод: | 4406330550 |
| Деталь: | WIRE-CH-060398 |
| Парткод: | 4402308040 |
| Деталь: | SPRING-TENS-CH |
| Парткод: | 4407402190 |
| Деталь: | HANGER-WIRE-CH |
| Парткод: | 4402308190 |
| Деталь: | SPC-TENSIONER |
| Парткод: | 6LA02262000 |
| Деталь: | TENSIONER-GRID |
| Парткод: | 6LA14299000 |
| Деталь: | LID-CH-M-F |
| Парткод: | 6LA02263000 |
| Деталь: | LID-CH-M-R |
| Парткод: | 6LA02293000 |
| Деталь: | GRID-340 |
| Парткод: | 6LA02260000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | S/PAN-M3X4-NI |
| Парткод: | X0-02113000 |
| Деталь: | RR/E-2-SS |
| Парткод: | X0-00963000 |
| Деталь: | S/PAN-M4X8-SS |
| Парткод: | X0-00170000 |
| Деталь: | FRAME-F/S-F |
| Парткод: | 6LA03812000 |
| Деталь: | K-FRAME-F/S-R |
| Парткод: | 6LA03826000 |
| Деталь: | ASYS-STAY-SPT-390 |
| Парткод: | 6LE05748000 |
| Деталь: | LEVER-SPT-ROL |
| Парткод: | 6LA04036000 |
| Деталь: | SPE061-050-0495 |
| Парткод: | 6LA04041000 |
| Деталь: | LEVER-P/U-DOWN |
| Парткод: | 6LA04031000 |
| Деталь: | SPE090-090-0531 |
| Парткод: | 6LA03887000 |
| Деталь: | ASYS-SHAFT-SPT-ROL |
| Парткод: | 6LE05725000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | SHAFT-FEED-ROL |
| Парткод: | 6LA14783000 |
| Деталь: | ASYS-ARM-PU-ROL |
| Парткод: | 6LE05730000 |
| Деталь: | BUSH-8X12X8F |
| Парткод: | 6LA65698000 |
| Деталь: | GEAR-08S026-06 |
| Парткод: | 6LA03897000 |
| Деталь: | K-GEAR-08S022-L |
| Парткод: | 6LA03904000 |
| Деталь: | ROLLER-FS-TR |
| Парткод: | 6LE05727000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | ACT-SW-EMPTY |
| Парткод: | 6LA03870000 |
| Деталь: | HRNS-FS-UNIT-390 |
| Парткод: | 6LE09603000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | MSB-1207 |
| Парткод: | F0-01250000 |
| Деталь: | GEAR-1.0-18 |
| Парткод: | 4400972560 |
| Деталь: | GEAR-08-30 |
| Парткод: | 4407906230 |
| Деталь: | GEAR-08S020-08 |
| Парткод: | 4406349590 |
| Деталь: | CLUCH-G28-08D |
| Парткод: | 6LA15184000 |
| Деталь: | COVER-F/S-CLT |
| Парткод: | 6LA03972000 |
| Деталь: | BRKT-SW-TR-F/S |
| Парткод: | 6LA03883000 |
| Деталь: | SPA-ACT-FS |
| Парткод: | 6LA03876000 |
| Деталь: | ACT-SW-TR-F/S |
| Парткод: | 6LA03881000 |
| Деталь: | CUSH-ACTR-STOP-390 |
| Парткод: | 6LE05749000 |
| Деталь: | PIN-ACTR |
| Парткод: | 6LE03108000 |
| Деталь: | BRKT-SW-SPT |
| Парткод: | 6LA03953000 |
| Деталь: | ACT-SW-SPT |
| Парткод: | 6LA03951000 |
| Деталь: | GEAR-08S022-06 |
| Парткод: | 6LA03898000 |
| Деталь: | ASYS-ROL-FEED |
| Парткод: | 6LA04047000 |
| Деталь: | CLUTCH-6-R |
| Парткод: | 4402833100 |
| Деталь: | K-STAY-FEED-T |
| Парткод: | 6LA03731000 |
| Деталь: | K-STAY-FEED |
| Парткод: | 6LA03831000 |
| Деталь: | SPL-F/S-TR |
| Парткод: | 6LA03950000 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | ASYS-GUIDE-FS-E |
| Парткод: | 6LA04038000 |
| Деталь: | GUIDE-FEED-U |
| Парткод: | 6LA03862000 |
| Деталь: | K-BRKT-GID-FEED |
| Парткод: | 6LA03987000 |
| Деталь: | GUIDE-FEED-L-T |
| Парткод: | 6LA04043000 |
| Деталь: | HLDR-GUIDE-FS |
| Парткод: | 6LE05756000 |
| Деталь: | GUIDE-F/S-TR-U |
| Парткод: | 6LA03944000 |
| Деталь: | HOLDER-F/S-TR |
| Парткод: | 6LA03947000 |
| Деталь: | BUSH-F6-GCB |
| Парткод: | 6LA03977000 |
| Деталь: | ASYS-ROL-SPT |
| Парткод: | 6LA04042000 |
| Деталь: | TL-SEP-ROL-Y |
| Парткод: | 6LA15790000 |
| Деталь: | BRAK-SPT |
| Парткод: | 6LA04032000 |
| Деталь: | SHEET-DUMP-EMP |
| Парткод: | 6LA03877000 |
| Деталь: | BRKT-HOLD-SP-390 |
| Парткод: | 6LE05718000 |
| Деталь: | ASYS-LEVER-SPT |
| Парткод: | 6LA04033000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | P/PRL/AH7-2X8-SS |
| Парткод: | X0-00979000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | SPE-P/U-110 |
| Парткод: | 6LA03873000 |
| Деталь: | SPE-P/U-75 |
| Парткод: | 6LA03874000 |
| Деталь: | LEVER-P/U-SND |
| Парткод: | 6LA03740000 |
| Деталь: | SOL-PICK-340 |
| Парткод: | 6LA15257000 |
| Деталь: | S/PAN-M3X4-NI |
| Парткод: | X0-02113000 |
| Деталь: | COVER-FRONT-LWR |
| Парткод: | 6LE04448000 |
| Деталь: | HINGE-COV-F-LWR |
| Парткод: | 6LE04453000 |
| Деталь: | MG-CATCH-44 |
| Парткод: | 6LE04463000 |
| Деталь: | PUSHER-SW-REV-390 |
| Парткод: | 6LE03121000 |
| Деталь: | BRKT-CATCH-MG |
| Парткод: | 6LE04451000 |
| Деталь: | LBL-TNR-IN |
| Парткод: | 6LE13139000 |
| Деталь: | COVER-FRONT-UPR |
| Парткод: | 6LE04447000 |
| Деталь: | HINGE-COV-F-UPR |
| Парткод: | 6LE04494000 |
| Деталь: | MG-CATCH-18 |
| Парткод: | 6LE04464000 |
| Деталь: | PUSHER-SWTNR-390 |
| Парткод: | 6LE04450000 |
| Деталь: | SPG-T-2R9XR55-HNDL |
| Парткод: | 6LE04495000 |
| Деталь: | COVER-FRONT-HNDL |
| Парткод: | 6LE04449000 |
| Деталь: | ASYS-INNER-CTR-390 |
| Парткод: | 6LE04444000 |
| Деталь: | LBL.W-DGR-LSR |
| Парткод: | 6LA15030000 |
| Деталь: | COV-SCREW-390 |
| Парткод: | 6LE08072000 |
| Деталь: | ASY-COVER-BYP |
| Парткод: | 6LE04456000 |
| Деталь: | CUSHION-COV-BYP-N |
| Парткод: | 6LA15048000 |
| Деталь: | COVER-WIN-LCF |
| Парткод: | 6LE04458000 |
| Деталь: | COVER-LATCH-LCF |
| Парткод: | 6LE04459000 |
| Деталь: | COV-IN-CONP-390 |
| Парткод: | 6LE07500000 |
| Деталь: | COV-INNER-R-390 |
| Парткод: | 6LE04410000 |
| Деталь: | LBL-W-DRUM-PS |
| Парткод: | 6LA06563000 |
| Деталь: | COVER-TOP-C |
| Парткод: | 6LE04436000 |
| Деталь: | Cover-Top-R |
| Парткод: | 6LE04438000 |
| Деталь: | COVER-LEFT-U |
| Парткод: | 6LE04473000 |
| Деталь: | PIN-HINGE-F-55 |
| Парткод: | 6LE04455000 |
| Деталь: | PIN-HINGE-UPR |
| Парткод: | 6LE04454000 |
| Деталь: | ASYS-COV-TOP-L |
| Парткод: | 6LE04461000 |
| Деталь: | LBL-DF-CLNG |
| Парткод: | 6LE04467000 |
| Деталь: | COVER-LEFT-R |
| Парткод: | 6LE04472000 |
| Деталь: | COVER-DF-CNT-FW |
| Парткод: | 6LE04474000 |
| Деталь: | COVER-SW-PW |
| Парткод: | 6LA00741000 |
| Деталь: | COV-HINGE-UPR-1 |
| Парткод: | 6LE04493000 |
| Деталь: | ASYS-CLOTH-SCN |
| Парткод: | 6LE16209000 |
| Деталь: | S/TPP/HEX-48-NI |
| Парткод: | 6LA08921000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | SCR-M48ITSR-NI |
| Парткод: | 6LA08934000 |
| Деталь: | S/TPP/HEX-410-NI |
| Парткод: | 6LA08922000 |
| Деталь: | ASYS-EMBLEM-520 |
| Парткод: | 6LE04489000 |
| Деталь: | ASYS-EMBLEM-600 |
| Парткод: | 6LE04487000 |
| Деталь: | ASYS-EMBLEM-720 |
| Парткод: | 6LE04485000 |
| Деталь: | ASYS-EMBLEM-850 |
| Парткод: | 6LE04470000 |
| Деталь: | LBL-PM-390 |
| Парткод: | 6LE04490000 |
| Деталь: | LBL-TNR-CAU-3-E |
| Парткод: | 4406359210 |
| Деталь: | ASYS-GUIDE-PAPER-390 |
| Парткод: | 6LE05736000 |
| Деталь: | ROLLER-IDLE-390 |
| Парткод: | 6LE05723000 |
| Деталь: | BUSH-D6-GCB |
| Парткод: | 4407976990 |
| Деталь: | SPRING-PFP-340 |
| Парткод: | 6LA14855000 |
| Деталь: | COVER-PFP-OPEN |
| Парткод: | 6LE05751000 |
| Деталь: | KNOB-COV-PFP |
| Парткод: | 6LE03422000 |
| Деталь: | SPC-KNOB-STOP |
| Парткод: | 6LA04152000 |
| Деталь: | BRKT-HINGE-U |
| Парткод: | 6LA04146000 |
| Деталь: | ASYS-COV-RIGHT-R-390 |
| Парткод: | 6LE04440000 |
| Деталь: | PLATE-FAX |
| Парткод: | 6LE04480000 |
| Деталь: | PLATE-PCI |
| Парткод: | 6LE04479000 |
| Деталь: | COVER-REAR-390 |
| Парткод: | 6LE04401000 |
| Деталь: | COVER-DL-REAR-390 |
| Парткод: | 6LE04446000 |
| Деталь: | COVER-RIGHT-L |
| Парткод: | 6LE04476000 |
| Деталь: | COVER-RIGHT-U |
| Парткод: | 6LE04475000 |
| Деталь: | RUBBER-COVER-R-390 |
| Парткод: | 6LE04492000 |
| Деталь: | POCKET-MANUAL |
| Парткод: | 6LE04477000 |
| Деталь: | LBL-LASER |
| Парткод: | 6LA47529000 |
| Деталь: | LBL-SERVICE-45 |
| Парткод: | 44204604000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/TPP/HEX-48-NI |
| Парткод: | 6LA08921000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | LABEL-FCC-18 |
| Парткод: | 6LA15839000 |
| Деталь: | LABEL-CANADA-A |
| Парткод: | 4408860880 |
| Деталь: | LBL-C-TICK-MARK |
| Парткод: | 4402860770 |
| Деталь: | LABEL-CHINA |
| Парткод: | 4400685400 |
| Деталь: | FOT-BRKT-COV |
| Парткод: | 6LA15783000 |
| Деталь: | CASTER-340 |
| Парткод: | 6LA00890000 |
| Деталь: | ASYS-BRKT-ADJ-390 |
| Парткод: | 6LE06312000 |
| Деталь: | FOOT-H-AD-502-ZU3 |
| Парткод: | 6LE06353000 |
| Деталь: | COVER-FRT-LWR-SID |
| Парткод: | 6LE04407000 |
| Деталь: | COVER-FRT-LWR |
| Парткод: | 6LE04408000 |
| Деталь: | HANDLE-BASE |
| Парткод: | 4406308710 |
| Деталь: | S/PAN/SWWP-M5X12-BSNI |
| Парткод: | X0-01110000 |
| Деталь: | SCREW40X08-T-ZU3 |
| Парткод: | 6LE04445000 |
| Деталь: | N/HEX/1-M8-SS |
| Парткод: | X0-00864000 |
| Деталь: | RAIL-CST-340-L |
| Парткод: | 6LA15761000 |
| Деталь: | RAIL-CST-340-R |
| Парткод: | 6LA15762000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/BID-M4X5-NI |
| Парткод: | X0-00447000 |
| Деталь: | WH-LIO-EXIT-SNS |
| Парткод: | 6LA09158000 |
| Деталь: | BRKT-SB-SNS |
| Парткод: | 6LA09227000 |
| Деталь: | BUSH6 |
| Парткод: | 6LA09062000 |
| Деталь: | CLIP5 |
| Парткод: | 6LA09057000 |
| Деталь: | MYLAR-L-EXIT |
| Парткод: | 6LA09395000 |
| Деталь: | PLT-R-17-ROL-F |
| Парткод: | 6LA09292000 |
| Деталь: | PLT-R-17-ROL-R |
| Парткод: | 6LA09300000 |
| Деталь: | PLT-SB-EXIT-TRY |
| Парткод: | 6LA09232000 |
| Деталь: | ROL-R-17 |
| Парткод: | 6LA09210000 |
| Деталь: | ROL-SB-EXIT |
| Парткод: | 6LA09362000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA09399000 |
| Деталь: | SCR-M3X6ITSR-NI |
| Парткод: | 6LA09396000 |
| Деталь: | SFT-R-SB3 |
| Парткод: | 6LA09314000 |
| Деталь: | SFT-SB-EXIT |
| Парткод: | 6LA09327000 |
| Деталь: | SENSOR |
| Парткод: | 6LE00886000 |
| Деталь: | SPL-SB-17-ROL |
| Парткод: | 6LA09290000 |
| Деталь: | SPE-SB-EXIT |
| Парткод: | 6LA09363000 |
| Деталь: | STAY-SB-LEXIT |
| Парткод: | 6LA09289000 |
| Деталь: | ERR040SK |
| Парткод: | 6LA09033000 |
| Деталь: | HLDR-SB-EXIT |
| Парткод: | 6LA09212000 |
| Деталь: | RSG-100 |
| Парткод: | 6LA09026000 |
| Деталь: | SCRW-3008FNBB |
| Парткод: | 6LA09011000 |
| Деталь: | HPIN20/10SCH |
| Парткод: | 6LA09038000 |
| Деталь: | REINF-BRKT-BYP |
| Парткод: | 6LA15837000 |
| Деталь: | REINF-MOULD-BYP |
| Парткод: | 6LA15838000 |
| Деталь: | LEVER-STOPPER |
| Парткод: | 6LA04708000 |
| Деталь: | SPRING-STOP-1 |
| Парткод: | 6LA04716000 |
| Деталь: | K-BRKT-STOPPER |
| Парткод: | 6LA14349000 |
| Деталь: | SPRING-SND-LVR |
| Парткод: | 6LA04712000 |
| Деталь: | SOL-SFB-340 |
| Парткод: | 6LA15259000 |
| Деталь: | LINK-SND-GEAR |
| Парткод: | 6LA04690000 |
| Деталь: | LEVER-GEAR |
| Парткод: | 6LA04691000 |
| Деталь: | SLIDER-STOPPER |
| Парткод: | 6LA04707000 |
| Деталь: | SCREW-SOCKET |
| Парткод: | 6LA08938000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | K-STAY-GUIDE-L |
| Парткод: | 6LA04638000 |
| Деталь: | LEV-ROL-SEP |
| Парткод: | 6LA04635000 |
| Деталь: | SPE060-080-0236 |
| Парткод: | 6LA04715000 |
| Деталь: | IDLR-BYPS-D16 |
| Парткод: | 6LA04672000 |
| Деталь: | SFT-IDL-TRS-BYP |
| Парткод: | 6LA04673000 |
| Деталь: | SPRING-SFT-TRS |
| Парткод: | 6LA04677000 |
| Деталь: | GUIDE-P-U |
| Парткод: | 6LA04630000 |
| Деталь: | BUSH-4-5 |
| Парткод: | 4407980920 |
| Деталь: | K-STAY-BYP-M |
| Парткод: | 6LA04662000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | LVR-PAPER-SW |
| Парткод: | 6LA04653000 |
| Деталь: | HRNS-SFB-PSW-390 |
| Парткод: | 6LE09606000 |
| Деталь: | BLT/T-154-2GT-4 |
| Парткод: | 6LA04627000 |
| Деталь: | BRKT-PICK-BYP |
| Парткод: | 6LA04692000 |
| Деталь: | SHAFT-PICK |
| Парткод: | 6LA04693000 |
| Деталь: | K-SHAFT-FED-BYP |
| Парткод: | 6LA04706000 |
| Деталь: | SHAFT-PICK-BRKT |
| Парткод: | 6LA04699000 |
| Деталь: | PLY-20-ROL |
| Парткод: | 4400884670 |
| Деталь: | PLY-20 |
| Парткод: | 4402813680 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | BLT/T-108-S2M-7 |
| Парткод: | 6LA04626000 |
| Деталь: | K-ROL-FED-CW-H |
| Парткод: | 4401773050 |
| Деталь: | K-RLR-P/U-24 |
| Парткод: | 6LA04694000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | PLY/T-S2M-28-06 |
| Парткод: | 6LA04721000 |
| Деталь: | K-GEAR-20-08-OW |
| Парткод: | 4401777990 |
| Деталь: | DMPR-SLIDER |
| Парткод: | 6LA04742000 |
| Деталь: | DMPR-PICK-UP |
| Парткод: | 6LA04743000 |
| Деталь: | WEIGHT-20-30 |
| Парткод: | 6LA04696000 |
| Деталь: | WEIGHT-10-15 |
| Парткод: | 6LA04697000 |
| Деталь: | BUSH-F6-GCB |
| Парткод: | 6LA03977000 |
| Деталь: | CUSHION-ACT-BYP |
| Парткод: | 6LA04646000 |
| Деталь: | CUSHION-GUIDE-P-U |
| Парткод: | 6LA04745000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | S/PAN/SWWP-M3X6-NI |
| Парткод: | X0-00060000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | P/PRL/AH7-2X8-SS |
| Парткод: | X0-00979000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | S/TPS/HEX-410-NI |
| Парткод: | 6LA08914000 |
| Деталь: | ASYS-STAY-AUG-390 |
| Парткод: | 6LE08564000 |
| Деталь: | MOTRD-AUG-390CCW |
| Парткод: | 6LE09545000 |
| Деталь: | ASYS-TERM-ANG-L |
| Парткод: | 6LA03042000 |
| Деталь: | BUSH-0613-06F-M |
| Парткод: | 6LA02367000 |
| Деталь: | AUGER-U-TNR-340 |
| Парткод: | 6LA03051000 |
| Деталь: | PIPE-20-22-164 |
| Парткод: | 6LA03050000 |
| Деталь: | SEAL-PIPE |
| Парткод: | 4401763290 |
| Деталь: | TERMINAL-AUG-R |
| Парткод: | 6LA03052000 |
| Деталь: | HRNS-AUG-MOT-390 |
| Парткод: | 6LE09198000 |
| Деталь: | SPC080-060-0120 |
| Парткод: | 6LA03054000 |
| Деталь: | GEAR-30 |
| Парткод: | 4401763230 |
| Деталь: | GP10S015/2GT063 |
| Парткод: | 6LA03048000 |
| Деталь: | BLT/T-164-2GT-4 |
| Парткод: | 6LA03049000 |
| Деталь: | SEAL-TERM-AUG-L |
| Парткод: | 4406327440 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | SEAL-BAG-U-TNR |
| Парткод: | 6LA03056000 |
| Деталь: | HRNS-LGC-FIN-390 |
| Парткод: | 6LE09128000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | SPLSN-6U |
| Парткод: | F0-00342000 |
| Деталь: | S/PAN-M2.6X2.5-NI |
| Парткод: | X0-02270000 |
| Деталь: | S/TPP/HEX-48-NI |
| Парткод: | 6LA08921000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | W/PL/PJO-6-SS |
| Парткод: | X0-00946000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | LWS-0711Z |
| Парткод: | F0-00736000 |
| Деталь: | CLN_DRUM-6000 |
| Парткод: | 6LE15207000 |
| Деталь: | MAIN-CH-6510 |
| Парткод: | 6LE15234000 |
| Деталь: | TR-BLT-6000 |
| Парткод: | 6LE15208000 |
| Деталь: | DEVE-UNIT-6000 |
| Парткод: | 6LE15204000 |
| Деталь: | DEVE-UNIT-8500 |
| Парткод: | 6LE15203000 |
| Деталь: | FUSER-6000-115 |
| Парткод: | 6LE06706000 |
| Деталь: | FUSER-8500-115 |
| Парткод: | 6LE06709000 |
| Деталь: | FUSER-6000-200 |
| Парткод: | 6LE06707000 |
| Деталь: | FUSER-8500-200 |
| Парткод: | 6LE06710000 |
| Деталь: | BRKT-SCRAPER-L |
| Парткод: | 6LA05404000 |
| Деталь: | ACT-EXIT-FUS |
| Парткод: | 6LA05410000 |
| Деталь: | ROL-EXIT-FUS-390 |
| Парткод: | 6LE06668000 |
| Деталь: | CLUTCH-HDL-FUS |
| Парткод: | 4401952430 |
| Деталь: | PIN-2-10 |
| Парткод: | 4408256620 |
| Деталь: | SPC-FUS-HNDL-LE |
| Парткод: | 4401758710 |
| Деталь: | HANDLE-FUS-390 |
| Парткод: | 6LE06629000 |
| Деталь: | GUIDE-PAPER-FUS |
| Парткод: | 6LA05406000 |
| Деталь: | SCRAPER-P/R |
| Парткод: | 4401758770 |
| Деталь: | SPE-SCRAPER-390 |
| Парткод: | 6LE06638000 |
| Деталь: | GEAR-10S22-6-P |
| Парткод: | 4406324110 |
| Деталь: | SPE-SW-EXIT |
| Парткод: | 4401758810 |
| Деталь: | BUSH-6 |
| Парткод: | 4401759090 |
| Деталь: | GUARD-FUS-LEVER |
| Парткод: | 6LA05364000 |
| Деталь: | BRKT-EX-ROL-UP |
| Парткод: | 6LA05367000 |
| Деталь: | BRKT-SCRAPER-U2 |
| Парткод: | 4406324510 |
| Деталь: | BRKT-LEV-HND-C |
| Парткод: | 4406324570 |
| Деталь: | COV-FUS-LEV-390 |
| Парткод: | 6LE06628000 |
| Деталь: | SCRAPER-212 |
| Парткод: | 4402491630 |
| Деталь: | ASY-ROL-FUS-UP |
| Парткод: | 6LA05377000 |
| Деталь: | STUD-LEV-CRANK |
| Парткод: | 4406324630 |
| Деталь: | STUD-CL-ROL-U-R |
| Парткод: | 4406324660 |
| Деталь: | SFT-LEV-HND-C |
| Парткод: | 4406324640 |
| Деталь: | SPE-050-050-216 |
| Парткод: | 6LA08943000 |
| Деталь: | SHEET-FUS-LEV-390 |
| Парткод: | 6LE06626000 |
| Деталь: | SPL-FUS-EX-BKT |
| Парткод: | 4406326180 |
| Деталь: | GUIDE-FUS-EX-F3 |
| Парткод: | 6LA05380000 |
| Деталь: | GUIDE-FUS-EX-R3 |
| Парткод: | 6LA05381000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | S/PAN/SWWP-M4X8-NI |
| Парткод: | X0-00164000 |
| Деталь: | S/PAN/SWWP-M3X6-NI |
| Парткод: | X0-00060000 |
| Деталь: | SCREW-FUSER-M4 |
| Парткод: | 4401759180 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | S/TPS/BID-3X6-ZU3 |
| Парткод: | X0-02069000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | WH-ORG-WISE-608 |
| Парткод: | 6LE04828000 |
| Деталь: | WH-IF-551 |
| Парткод: | 6LA09146000 |
| Деталь: | WH-SIZE-CNT-608 |
| Парткод: | 6LE04827000 |
| Деталь: | WH-SW-551 |
| Парткод: | 6LA09147000 |
| Деталь: | ASM-HINGE-551L |
| Парткод: | 6LA09077000 |
| Деталь: | ASM-HINGE-551R |
| Парткод: | 6LA09078000 |
| Деталь: | ASY-S-SOL-SUB |
| Парткод: | 6LA09113000 |
| Деталь: | BRKT-DF-IDSW |
| Парткод: | 6LA09306000 |
| Деталь: | BRKT-M-LGC |
| Парткод: | 6LA09282000 |
| Деталь: | BRKT-S-SOL |
| Парткод: | 6LA09278000 |
| Деталь: | DUCT-R |
| Парткод: | 6LA09240000 |
| Деталь: | LVR-DF-ILSW |
| Парткод: | 6LA09243000 |
| Деталь: | PWA-F-LGC-608 |
| Парткод: | 6LE04801000 |
| Деталь: | SCRW-DAN7.7-NI |
| Парткод: | 6LA09398000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA09399000 |
| Деталь: | SCR-M4X8ITSR-NI |
| Парткод: | 6LA09397000 |
| Деталь: | SPL-FEED-COV-SW |
| Парткод: | 6LA09279000 |
| Деталь: | HNG-STP |
| Парткод: | 6LA09419000 |
| Деталь: | TBID4008FNBI |
| Парткод: | 6LA09444000 |
| Деталь: | ANGL-DF-SW |
| Парткод: | 6LA09439000 |
| Деталь: | SCR-M3X6ITSR-NI |
| Парткод: | 6LA09396000 |
| Деталь: | SHEET-HINGE |
| Парткод: | 6LA09441000 |
| Деталь: | SCREW-M45-3.5 |
| Парткод: | 6LA09001000 |
| Деталь: | SWITCH-DE2L |
| Парткод: | 6LA09018000 |
| Деталь: | EDS0607U |
| Парткод: | 6LA09024000 |
| Деталь: | EDS01 |
| Парткод: | 6LA09022000 |
| Деталь: | KGLS-8RT |
| Парткод: | 6LA09023000 |
| Деталь: | KGPS-8RF |
| Парткод: | 6LA09025000 |
| Деталь: | LWSS-2N |
| Парткод: | 6LA09028000 |
| Деталь: | CLMP-MSBS-1207 |
| Парткод: | 6LA09027000 |
| Деталь: | RMLC-05T-V0 |
| Парткод: | 6LA09031000 |
| Деталь: | RLMC-2T-V0 |
| Парткод: | 6LA09029000 |
| Деталь: | RSG-100 |
| Парткод: | 6LA09026000 |
| Деталь: | KI-100 |
| Парткод: | 6LA09020000 |
| Деталь: | SCRW-030060FNWS |
| Парткод: | 6LA09010000 |
| Деталь: | SCRW-M2.3-12 |
| Парткод: | 6LA09008000 |
| Деталь: | SCRW-3005FNWS |
| Парткод: | 6LA09009000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | MOTRS-RVS-390 |
| Парткод: | 6LE09156000 |
| Деталь: | ROLLER-REVERS |
| Парткод: | 6LE03109000 |
| Деталь: | ROLLER-REV-ADU |
| Парткод: | 6LE03110000 |
| Деталь: | BRG-688ZZNR |
| Парткод: | 4408510800 |
| Деталь: | GUIDE-ADU-IN-390 |
| Парткод: | 6LE03130000 |
| Деталь: | K-GUIDE-I-340 |
| Парткод: | 6LA05920000 |
| Деталь: | STUD-POS-REV-R |
| Парткод: | 6LA05929000 |
| Деталь: | PLY/T-3GT023-DB |
| Парткод: | 6LA05935000 |
| Деталь: | PLY/T-3GT023-08 |
| Парткод: | 6LA05936000 |
| Деталь: | BLT/T-312-3GT-6 |
| Парткод: | 6LA05938000 |
| Деталь: | BLT/T-201-3GT-6 |
| Парткод: | 6LA05939000 |
| Деталь: | SPLSN-6U |
| Парткод: | F0-00342000 |
| Деталь: | PWA-F-MOT2-390RV |
| Парткод: | 6LE09140100 |
| Деталь: | HRNS-REV-MOT-390 |
| Парткод: | 6LE09204000 |
| Деталь: | GUIDE-REV-I-SUB |
| Парткод: | 6LA05922000 |
| Деталь: | MYLAR-MOT-EXIT |
| Парткод: | 6LA05628000 |
| Деталь: | MOTRS-EXIT-390 |
| Парткод: | 6LE09169000 |
| Деталь: | K-BKT-MOT-EXIT |
| Парткод: | 6LA05622000 |
| Деталь: | GEAR-10S021-06 |
| Парткод: | 6LA05627000 |
| Деталь: | K-BRKT-HIG-EX-L |
| Парткод: | 6LA05753000 |
| Деталь: | BRKT-HIG-EX-STP |
| Парткод: | 6LA05759000 |
| Деталь: | SEAL-REV-SW |
| Парткод: | 6LA05918000 |
| Деталь: | MYLAR-GUIDE-ADU |
| Парткод: | 6LA14342000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/PAN/SWWP-M4X8-NI |
| Парткод: | X0-00164000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | S/HEX-M36-NI |
| Парткод: | 6LA08900000 |
| Деталь: | RR/E-6-SS |
| Парткод: | X0-00967000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | ASY-PWA-SYS-390S |
| Парткод: | 6LE09599000 |
| Деталь: | SPG-F-SYS-390 |
| Парткод: | 6LE05422000 |
| Деталь: | COV-CNCT-DWN |
| Парткод: | 6LA34629000 |
| Деталь: | COVER-USB-SYS |
| Парткод: | 6LA64243000 |
| Деталь: | BUSH-KG-016L-SYS |
| Парткод: | 6LE05412000 |
| Деталь: | COVER-SYS-390 |
| Парткод: | 6LE05403000 |
| Деталь: | FAND-6010-390 |
| Парткод: | 6LE09299000 |
| Деталь: | ECB-207-01 |
| Парткод: | F0-01351000 |
| Деталь: | DWV6S8/P |
| Парткод: | C0-11036000 |
| Деталь: | WD400BB-22JHC0 |
| Парткод: | G0-00360000 |
| Деталь: | HED-1111-ALS20ABK |
| Парткод: | F0-01327000 |
| Деталь: | SCREW-HDD-CASE |
| Парткод: | 6LA56769000 |
| Деталь: | BRKT-HDD-390 |
| Парткод: | 6LE05425000 |
| Деталь: | STK16C88-3WF45 |
| Парткод: | C0-12295000 |
| Деталь: | HRNS-HDDFG-390 |
| Парткод: | 6LE09280000 |
| Деталь: | HRNS-HDD-POW-390 |
| Парткод: | 6LE09244000 |
| Деталь: | HRNS-HDD-SIG-390 |
| Парткод: | 6LE09243000 |
| Деталь: | SCREW-6-321/4 |
| Парткод: | 44201086000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | SPS-3U |
| Парткод: | F0-00027000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | EDS-1717U |
| Парткод: | F0-00047000 |
| Деталь: | SCREW40X08-T-ZU3 |
| Парткод: | 6LE04445000 |
| Деталь: | LWS-0711Z |
| Парткод: | F0-00736000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/TPS/PAN-4X16-ZU3 |
| Парткод: | X0-02066000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | SPL-PUSH-RGST |
| Парткод: | 4406349800 |
| Деталь: | FRAME-RGST-390 |
| Парткод: | 6LE05745000 |
| Деталь: | ACTUATOR-RGST-N |
| Парткод: | 6LA15024000 |
| Деталь: | SPL-ACT-RGT |
| Парткод: | 4401772510 |
| Деталь: | BRKT-SW-RGT-340 |
| Парткод: | 6LA03326000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | HRNS-RGTSW-390 |
| Парткод: | 6LE09602000 |
| Деталь: | ROL-RGST-D-390 |
| Парткод: | 6LE05769000 |
| Деталь: | GEAR-0.8-25 |
| Парткод: | 4407547320 |
| Деталь: | ROLL-RGST-U-390 |
| Парткод: | 6LE05720000 |
| Деталь: | BRG-1680ZZ |
| Парткод: | 4407922440 |
| Деталь: | BUSH-RGST-D |
| Парткод: | 4406349770 |
| Деталь: | CLIP-RGST |
| Парткод: | 4406349790 |
| Деталь: | SPRING-1150 |
| Парткод: | 6LA08949000 |
| Деталь: | BUSH-RGST-UNIT |
| Парткод: | 4406349850 |
| Деталь: | K-GUIDE-RGST-L |
| Парткод: | 6LA03335000 |
| Деталь: | K-GUIDE-TR |
| Парткод: | 4406349920 |
| Деталь: | SPL-ROL-RGST |
| Парткод: | 4406349880 |
| Деталь: | ASYS-BRK-BRS-RGT-L-390 |
| Парткод: | 6LE05767000 |
| Деталь: | GEAR-08S020-08 |
| Парткод: | 4406349590 |
| Деталь: | BUSH-RGST-U |
| Парткод: | 4406349550 |
| Деталь: | 696T12ZZ1MC3E |
| Парткод: | F0-00023000 |
| Деталь: | PULLY-3GT16-06-390 |
| Парткод: | 6LE05719000 |
| Деталь: | GUIDE-RGST-U |
| Парткод: | 6LA03341000 |
| Деталь: | MOTRS-RGT-390 |
| Парткод: | 6LE09196000 |
| Деталь: | BRKT-MOT-RGST-390 |
| Парткод: | 6LE05747000 |
| Деталь: | SUPPORT-GUIDE-P |
| Парткод: | 4401772280 |
| Деталь: | BLT/T-174-3GT-4 |
| Парткод: | 4406350060 |
| Деталь: | K-JNT-GUIDE-U-S |
| Парткод: | 6LA03350000 |
| Деталь: | K-JNT-RGT-FRT-R |
| Парткод: | 6LA03380000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | RR/E-2-SS |
| Парткод: | X0-00963000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | S/HEX-M48-NI |
| Парткод: | 6LA08905000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/PAN/SWWP-M3X10-NI |
| Парткод: | X0-00094000 |
| Деталь: | WH-SW-551 |
| Парткод: | 6LA09147000 |
| Деталь: | ASYS-BKT-UD-MOT |
| Парткод: | 6LA09111000 |
| Деталь: | BLT-122-S2M-6 |
| Парткод: | 6LA09043000 |
| Деталь: | BLT-152-S2M-6 |
| Парткод: | 6LA09045000 |
| Деталь: | BLT-192-S2M-6 |
| Парткод: | 6LA09047000 |
| Деталь: | BRKT-DF-APS |
| Парткод: | 6LA09245000 |
| Деталь: | BRKT-MOT-L/O |
| Парткод: | 6LA09266000 |
| Деталь: | BUSH-10 |
| Парткод: | 6LA09063000 |
| Деталь: | BUSH6 |
| Парткод: | 6LA09062000 |
| Деталь: | CLIP4 |
| Парткод: | 6LA09074000 |
| Деталь: | CLIP5 |
| Парткод: | 6LA09057000 |
| Деталь: | SWITCH-DE2L |
| Парткод: | 6LA09018000 |
| Деталь: | GEAR-0.8-23 |
| Парткод: | 6LA09056000 |
| Деталь: | GEAR-08-40-20 |
| Парткод: | 6LA09182000 |
| Деталь: | GER-80-20-37-OW |
| Парткод: | 6LA09349000 |
| Деталь: | HLDR-T-R |
| Парткод: | 6LA09203000 |
| Деталь: | LVR-DF-APS |
| Парткод: | 6LA09244000 |
| Деталь: | M/DC-FEED-551 |
| Парткод: | 6LA09141000 |
| Деталь: | MOTR.S-PLT-PICK |
| Парткод: | 6LE04822000 |
| Деталь: | PLT-R-MOT-TEN |
| Парткод: | 6LA09273000 |
| Деталь: | PLY/T-S2M-25-OW |
| Парткод: | 6LA09465000 |
| Деталь: | PLY/T-S2M-30 |
| Парткод: | 6LA09430000 |
| Деталь: | PLY/T-S2M-24-10 |
| Парткод: | 6LA09180000 |
| Деталь: | PLY/T-S2M-30-6 |
| Парткод: | 6LA09179000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA09399000 |
| Деталь: | SCR-M3X6ITSR-NI |
| Парткод: | 6LA09396000 |
| Деталь: | SFT-READ-DRV-1 |
| Парткод: | 6LA09317000 |
| Деталь: | SFT-READ-DRV-2 |
| Парткод: | 6LA09318000 |
| Деталь: | SNS-SPG-F-DF |
| Парткод: | 6LA09073000 |
| Деталь: | SPL-FEED-COV-SW |
| Парткод: | 6LA09279000 |
| Деталь: | SPE-FEED-MOT-L |
| Парткод: | 6LA09357000 |
| Деталь: | CLIP-3KL |
| Парткод: | 6LA09059000 |
| Деталь: | EDS0607U |
| Парткод: | 6LA09024000 |
| Деталь: | ERR050SK |
| Парткод: | 6LA09034000 |
| Деталь: | SCRW-4006FNIT |
| Парткод: | 6LA09015000 |
| Деталь: | RSG-100 |
| Парткод: | 6LA09026000 |
| Деталь: | SNS-TLP1241 |
| Парткод: | 6LE00883000 |
| Деталь: | SCRW-030060FNWS |
| Парткод: | 6LA09010000 |
| Деталь: | SCRW-M2.3-12 |
| Парткод: | 6LA09008000 |
| Деталь: | BUSH-06 |
| Парткод: | 6LA09017000 |
| Деталь: | HPIN20/10SCH |
| Парткод: | 6LA09038000 |
| Деталь: | BRKT-FUS-ENT-U |
| Парткод: | 6LA05313000 |
| Деталь: | GUIDE-FUS-ENT-U |
| Парткод: | 6LA05304000 |
| Деталь: | BRKT-THERMO-H/R |
| Парткод: | 6LA05310000 |
| Деталь: | THRMST-340-FUS |
| Парткод: | 6LA07172000 |
| Деталь: | BRKT-THMS-H/R |
| Парткод: | 6LA05309000 |
| Деталь: | THMS-HTR-U-390 |
| Парткод: | 6LE09610000 |
| Деталь: | PLWS-1-46B |
| Парткод: | F0-00032000 |
| Деталь: | HRNS-IH-AC1-390 |
| Парткод: | 6LE09437000 |
| Деталь: | HRNS-IH-AC2-340 |
| Парткод: | 6LA07431000 |
| Деталь: | BUSH-6 |
| Парткод: | 4401759090 |
| Деталь: | CW-6000 |
| Парткод: | 6LE19372000 |
| Деталь: | PR-6000W |
| Парткод: | 6LE19373000 |
| Деталь: | BRKT-WEB-R-390 |
| Парткод: | 6LE06634000 |
| Деталь: | BRKT-WEB-F-390 |
| Парткод: | 6LE06633000 |
| Деталь: | GUARD-FUS-CLN-U |
| Парткод: | 6LA05444000 |
| Деталь: | SPE-050-050-216 |
| Парткод: | 6LA08943000 |
| Деталь: | GEAR-08S35-06-F |
| Парткод: | 6LA05455000 |
| Деталь: | BRKT-FUS-WEB-E |
| Парткод: | 6LA05454000 |
| Деталь: | GG08H035/08S14L |
| Парткод: | 6LA05452000 |
| Деталь: | SHEET-FUS-CLN-U |
| Парткод: | 6LA05470000 |
| Деталь: | SPL-FUS-F |
| Парткод: | 6LA05472000 |
| Деталь: | GUIDE-FUS-ENT-L |
| Парткод: | 4406325090 |
| Деталь: | BRKT-FUS-ENT-L390 |
| Парткод: | 6LE06662000 |
| Деталь: | BRKT-THMS-L390 |
| Парткод: | 6LE06663000 |
| Деталь: | HRNS-FUS-390 |
| Парткод: | 6LE09155000 |
| Деталь: | BRUSH-SUS-HR |
| Парткод: | 6LE06669000 |
| Деталь: | THMS-HTR-L-300 |
| Парткод: | 4406379760 |
| Деталь: | COV-THMS-HT-FUS |
| Парткод: | 4406325120 |
| Деталь: | K-HLD-THERMO |
| Парткод: | 6LA05317000 |
| Деталь: | SHEET-FUS-ENT-U |
| Парткод: | 6LA05286000 |
| Деталь: | ASYS-GUIDE-EN-390 |
| Парткод: | 6LE06630000 |
| Деталь: | BRG-ONEWAY-6-H |
| Парткод: | 6LA05468000 |
| Деталь: | SPACER-FUS-WEB |
| Парткод: | 6LA05458000 |
| Деталь: | S/TPS/BID-3X6-ZU3 |
| Парткод: | X0-02069000 |
| Деталь: | S/PAN/SWWP-M3X6-NI |
| Парткод: | X0-00060000 |
| Деталь: | S/HEX-M310-NI |
| Парткод: | 6LA08902000 |
| Деталь: | SCREW-FUSER-M4 |
| Парткод: | 4401759180 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 6LA08937000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | S/PAN/SWWP-M3X10-NI |
| Парткод: | X0-00094000 |
| Деталь: | K-BRKT-HOLD |
| Парткод: | 4406350450 |
| Деталь: | BRKT-SLIDE |
| Парткод: | 4406350480 |
| Деталь: | SLIDER-F |
| Парткод: | 4406350520 |
| Деталь: | SLIDER-R |
| Парткод: | 4406350530 |
| Деталь: | SPE110-100-0435 |
| Парткод: | 6LA08945000 |
| Деталь: | RAIL-TRU-340 |
| Парткод: | 6LA15814000 |
| Деталь: | STUD-RAIL-TRU |
| Парткод: | 4406337910 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | SPLSN-3U |
| Парткод: | F0-00316000 |
| Деталь: | SNSR-V0-390 |
| Парткод: | 6LE09194000 |
| Деталь: | HOLDER-SNR-V0 |
| Парткод: | 6LA14473000 |
| Деталь: | COVER-SNR-V0 |
| Парткод: | 6LA02285000 |
| Деталь: | SM-SSO1GL2T |
| Парткод: | 4407966810 |
| Деталь: | SCREW20D23 |
| Парткод: | 44204394000 |
| Деталь: | HRNS-V0-SNR-390 |
| Парткод: | 6LE09406000 |
| Деталь: | BAND-PS100 |
| Парткод: | 4400902490 |
| Деталь: | SPL-ADU-TRANS |
| Парткод: | 6LA06435000 |
| Деталь: | WALL-RAIL-CLN |
| Парткод: | 6LA02242000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | S/PAN-M4X8-NI |
| Парткод: | X0-00162000 |
| Деталь: | S/TPS/PAN-4X8-ZU3 |
| Парткод: | X0-02063000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | ASY-GID-S-OPEN |
| Парткод: | 6LA09126000 |
| Деталь: | ASY-S-SHT |
| Парткод: | 6LA09130000 |
| Деталь: | BAND-S-AP |
| Парткод: | 6LA09390000 |
| Деталь: | GID-S-OPEN |
| Парткод: | 6LE04808000 |
| Деталь: | HDL-S-LATCH93 |
| Парткод: | 6LE04802000 |
| Деталь: | SCRW-M3-3.2 |
| Парткод: | 6LA09434000 |
| Деталь: | MIRROR-1005 |
| Парткод: | 6LA09351000 |
| Деталь: | PLT-SHEET-PLTN |
| Парткод: | 6LA09194000 |
| Деталь: | PLT-S-OPEN |
| Парткод: | 6LA09275000 |
| Деталь: | ROLL-SB |
| Парткод: | 6LA09070000 |
| Деталь: | SCR-DAN-3X8 |
| Парткод: | 6LA09372000 |
| Деталь: | SCR-M3X6ITSR-NI |
| Парткод: | 6LA09396000 |
| Деталь: | CUSH-S-PLTN |
| Парткод: | 6LA09388000 |
| Деталь: | SPE-S-HDL |
| Парткод: | 6LA09368000 |
| Деталь: | SPL-S-ROL |
| Парткод: | 6LA09261000 |
| Деталь: | TAPE-F-PRS-L |
| Парткод: | 6LA09075000 |
| Деталь: | SCRW-3008FNBB |
| Парткод: | 6LA09011000 |
| Деталь: | 1HWAS030FNM |
| Парткод: | 6LA09041000 |
| Деталь: | GLASS-DUCT |
| Парткод: | 6LA01531000 |
| Деталь: | COV-GLASS-DUCT |
| Парткод: | 6LA01532000 |
| Деталь: | SPG-F-LSU-390 |
| Парткод: | 6LE07255000 |
| Деталь: | BASE-FAN |
| Парткод: | 6LA01541000 |
| Деталь: | FAND-8025-390 |
| Парткод: | 6LE09166000 |
| Деталь: | COVER-DL-PLG |
| Парткод: | 6LE07250000 |
| Деталь: | COVER-DL-SCN-390 |
| Парткод: | 6LE08056000 |
| Деталь: | RAIL-INS-OPT |
| Парткод: | 6LA01570000 |
| Деталь: | SPL-FG-PLG |
| Парткод: | 6LA01565000 |
| Деталь: | LSU-UNIT-F390S |
| Парткод: | 6LE07257000 |
| Деталь: | LSU-UNIT-F392S |
| Парткод: | 6LE07258000 |
| Деталь: | SPG-LSU-LFT-390 |
| Парткод: | 6LE07225000 |
| Деталь: | ASY-F-PLG-390S |
| Парткод: | 6LE09543000 |
| Деталь: | ASY-F-PLG-392S |
| Парткод: | 6LE09543100 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/TPS/PAN-4X32-ZU3 |
| Парткод: | X0-02114000 |
| Деталь: | ASYS-SCREW-LSU-NI |
| Парткод: | 6LA36749000 |
| Деталь: | ASY-SCREW-OPT |
| Парткод: | 6LA01590000 |
| Деталь: | SEAL-SCREW |
| Парткод: | 6LA01593000 |
| Деталь: | SPL-UP-HOUSING |
| Парткод: | 6LA01563000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | BRKT-SND-340 |
| Парткод: | 6LA05706000 |
| Деталь: | SOL-GATE-390 |
| Парткод: | 6LE09192000 |
| Деталь: | SPE-040-026-119 |
| Парткод: | 6LA05704000 |
| Деталь: | LINK-SOL-ADU |
| Парткод: | 6LA05705000 |
| Деталь: | HNDL-HOOK-EXIT |
| Парткод: | 6LE03133000 |
| Деталь: | SPC072-070-0135 |
| Парткод: | 6LA05715000 |
| Деталь: | K-BRKT-HNDL-EX |
| Парткод: | 6LA05712000 |
| Деталь: | BRKT-STOP-EXIT |
| Парткод: | 6LA05716000 |
| Деталь: | SPA-HNDL-EXIT |
| Парткод: | 6LA05717000 |
| Деталь: | PUSHER-SW-REV-390 |
| Парткод: | 6LE03121000 |
| Деталь: | CS1A-B2CA |
| Парткод: | E0-01853000 |
| Деталь: | FAND-8025-390 |
| Парткод: | 6LE09166000 |
| Деталь: | HRNS-REV-OPEN-390 |
| Парткод: | 6LE09604000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | BRKT-ACTR-REV |
| Парткод: | 6LA05671000 |
| Деталь: | ACTR-REV |
| Парткод: | 6LA05668000 |
| Деталь: | CUSH-ACTR-REV |
| Парткод: | 6LA05674000 |
| Деталь: | PIN-ACTR-REV |
| Парткод: | 6LA05679000 |
| Деталь: | SPA-ACTR |
| Парткод: | 6LA05678000 |
| Деталь: | BRKT-ACTR-ADU-390 |
| Парткод: | 6LE03126000 |
| Деталь: | ACTR-ADU |
| Парткод: | 6LA05675000 |
| Деталь: | CUSH-ACTR-STOP-390 |
| Парткод: | 6LE05749000 |
| Деталь: | PIN-ACTR |
| Парткод: | 6LE03108000 |
| Деталь: | BRKT-EXIT-SW |
| Парткод: | 6LA05655000 |
| Деталь: | SNSR-FED-RVS-390 |
| Парткод: | 6LE09174000 |
| Деталь: | LBL-W-HOT-EXIT |
| Парткод: | 6LA06574000 |
| Деталь: | COVER-EXIT-OPEN |
| Парткод: | 6LA05792000 |
| Деталь: | S/HEX-M36-NI |
| Парткод: | 6LA08900000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | S/TPS/PAN-4X32-ZU3 |
| Парткод: | X0-02114000 |
| Деталь: | S/TP/FPAN2/S-3X8-NI |
| Парткод: | X0-02115000 |
| Деталь: | SCR-M48ITSR-NI |
| Парткод: | 6LA08934000 |
| Деталь: | ASY-GID-R-NA-L |
| Парткод: | 6LA09083000 |
| Деталь: | ASY-GID-R-NA-S |
| Парткод: | 6LA09082000 |
| Деталь: | BRG-100300F |
| Парткод: | 6LA09050000 |
| Деталь: | BLT-260-S2M-10 |
| Парткод: | 6LA09048000 |
| Деталь: | BRKT-R-MOT |
| Парткод: | 6LA09272000 |
| Деталь: | BRKT-R-PG |
| Парткод: | 6LA09269000 |
| Деталь: | BRKT-R-RSNS |
| Парткод: | 6LA09271000 |
| Деталь: | BLOCK-R-PG-F |
| Парткод: | 6LA09183000 |
| Деталь: | BLOCK-R-PG-R |
| Парткод: | 6LA09234000 |
| Деталь: | CLIP5 |
| Парткод: | 6LA09057000 |
| Деталь: | CVR-L |
| Парткод: | 6LE04816000 |
| Деталь: | CVR-R-RSNS |
| Парткод: | 6LA09308000 |
| Деталь: | SPL-C-GUIDE |
| Парткод: | 6LA09071000 |
| Деталь: | DIL-R-JAM93 |
| Парткод: | 6LE04803000 |
| Деталь: | FLP-SB-L |
| Парткод: | 6LA09213000 |
| Деталь: | GEAR-0.8-60 |
| Парткод: | 6LA09185000 |
| Деталь: | GUID-R-PLTN |
| Парткод: | 6LA09274000 |
| Деталь: | GUID-R-READ |
| Парткод: | 6LA09255000 |
| Деталь: | GUIDE-SB-C |
| Парткод: | 6LA09159000 |
| Деталь: | GUID-SB-P-N |
| Парткод: | 6LA09468000 |
| Деталь: | KNB-C-CP |
| Парткод: | 6LA95719000 |
| Деталь: | SCRW-M3-3.2 |
| Парткод: | 6LA09434000 |
| Деталь: | MIRROR-R-RSNS |
| Парткод: | 6LA09301000 |
| Деталь: | MYLAR-SB-CGID |
| Парткод: | 6LA09377000 |
| Деталь: | MYLAR-R-SNS |
| Парткод: | 6LA09352000 |
| Деталь: | MIRROR-SB-CGID |
| Парткод: | 6LA09365000 |
| Деталь: | M/DC-READ-551 |
| Парткод: | 6LA09142000 |
| Деталь: | SPL-GUIDE-NA |
| Парткод: | 6LA09066000 |
| Деталь: | PLT-R-MOT-TEN |
| Парткод: | 6LA09273000 |
| Деталь: | PLT-SB-PGUID |
| Парткод: | 6LA09224000 |
| Деталь: | PLY/T-S2M-108 |
| Парткод: | 6LA09162000 |
| Деталь: | CLMP-RLMC-01TVO |
| Парткод: | 6LA09030000 |
| Деталь: | ROLLER-R-READ |
| Парткод: | 6LA09337000 |
| Деталь: | SCR-M3X6ITSR-NI |
| Парткод: | 6LA09396000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA09399000 |
| Деталь: | SNS-SPI-339 |
| Парткод: | 6LE04819000 |
| Деталь: | SPE-TNS-READ |
| Парткод: | 6LA09405000 |
| Деталь: | SPL-SB-FLP |
| Парткод: | 6LA09382000 |
| Деталь: | STAY-R-L |
| Парткод: | 6LA09260000 |
| Деталь: | CLIP-3KL |
| Парткод: | 6LA09059000 |
| Деталь: | SHEET-6-6-T1 |
| Парткод: | 6LA09440000 |
| Деталь: | MYR-R-CLEAN |
| Парткод: | 6LA09338000 |
| Деталь: | EDS0607U |
| Парткод: | 6LA09024000 |
| Деталь: | EDS02 |
| Парткод: | 6LA09021000 |
| Деталь: | ERR080SK |
| Парткод: | 6LA09036000 |
| Деталь: | SCRW-4006FNIT |
| Парткод: | 6LA09015000 |
| Деталь: | RSG-100 |
| Парткод: | 6LA09026000 |
| Деталь: | SCRW-030060FNWS |
| Парткод: | 6LA09010000 |
| Деталь: | SCRW-3008FNSW |
| Парткод: | 6LA09012000 |
| Деталь: | SCRW-3008FNBB |
| Парткод: | 6LA09011000 |
| Деталь: | WPIN40/18FPA |
| Парткод: | 6LA09438000 |
| Деталь: | HPIN20/16 |
| Парткод: | 6LA09040000 |
| Деталь: | DUCT-EXIT-340 |
| Парткод: | 6LE06332000 |
| Деталь: | ASYS-DUCT-CLN |
| Парткод: | 6LA01371000 |
| Деталь: | FAN.D-8025-340 |
| Парткод: | 6LA07126000 |
| Деталь: | BRKT-FAN-RVS |
| Парткод: | 6LA01364000 |
| Деталь: | SEAL-DUCT-EXIT11-390 |
| Парткод: | 6LE06368000 |
| Деталь: | ASYS-GUIDE-DUCT |
| Парткод: | 6LA02751000 |
| Деталь: | SEAL-DUCT-EXIT1-390 |
| Парткод: | 6LE06363000 |
| Деталь: | SEAL-DUCT-EXIT2 |
| Парткод: | 6LA01379000 |
| Деталь: | SEAL-DUCT-EXIT3 |
| Парткод: | 6LA01380000 |
| Деталь: | SEAL-DUCT-EXIT4-390 |
| Парткод: | 6LE06364000 |
| Деталь: | SEAL-DUCT-EXIT5 |
| Парткод: | 6LA01382000 |
| Деталь: | SEAL-DUCT-EXIT6 |
| Парткод: | 6LA01383000 |
| Деталь: | SEAL-DUCT-EXIT7 |
| Парткод: | 6LA01384000 |
| Деталь: | SEAL-DUCT-EXIT8 |
| Парткод: | 6LA01385000 |
| Деталь: | DUCT-REAR-U1 |
| Парткод: | 6LA14287000 |
| Деталь: | DUCT-REAR-U2 |
| Парткод: | 6LA14288000 |
| Деталь: | SEAL-DUCT-R-U1 |
| Парткод: | 6LA01375000 |
| Деталь: | SEAL-DUCT-R-U2 |
| Парткод: | 6LA01376000 |
| Деталь: | SEAL-DUCT-R-L |
| Парткод: | 6LA01377000 |
| Деталь: | SEAL-DUCT-U |
| Парткод: | 6LA01035000 |
| Деталь: | SEAL-DUCT-FAN |
| Парткод: | 6LA01036000 |
| Деталь: | MYLAR-DUCT |
| Парткод: | 6LA01394000 |
| Деталь: | FLTR-OZN-R190-390 |
| Парткод: | 6LE06360000 |
| Деталь: | ASYS-FILTER-OZN |
| Парткод: | 6LE06371000 |
| Деталь: | FLTR-OZN-800-390 |
| Парткод: | 6LE06359000 |
| Деталь: | MYLAR-DUCT2-390 |
| Парткод: | 6LE06362000 |
| Деталь: | MYLAR-DUCT-390 |
| Парткод: | 6LE06361000 |
| Деталь: | SEAL-DUCT-R-U1-390 |
| Парткод: | 6LE06365000 |
| Деталь: | SEAL-DUCT-R-U2-390 |
| Парткод: | 6LE06366000 |
| Деталь: | SEAL-DUCT-R-U-390 |
| Парткод: | 6LE06374000 |
| Деталь: | S/TPS/PAN-4X32-ZU3 |
| Парткод: | X0-02114000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | WAS-08-120-13-P |
| Парткод: | 6LA04256000 |
| Деталь: | MOTRD-FEED-390 |
| Парткод: | 6LE09189000 |
| Деталь: | SPLSN-4U |
| Парткод: | F0-00340000 |
| Деталь: | BLT/T-297-3GT-4 |
| Парткод: | 6LA04271000 |
| Деталь: | PLY-Z25-3M-DBL |
| Парткод: | 4401783340 |
| Деталь: | LWS-0711Z |
| Парткод: | F0-00736000 |
| Деталь: | LWS-2111Z |
| Парткод: | F0-01299000 |
| Деталь: | CASE-DRV-TRY340 |
| Парткод: | 6LA04321000 |
| Деталь: | case-drv-try-r |
| Парткод: | 44201851000 |
| Деталь: | CPG-LIFT-340 |
| Парткод: | 6LA04322000 |
| Деталь: | SPC172-100-3400 |
| Парткод: | 4401966050 |
| Деталь: | GER-TRAY-21 |
| Парткод: | 41306025000 |
| Деталь: | GER-TRAY-24-14 |
| Парткод: | 41306024000 |
| Деталь: | G06S-13/G05S-80 |
| Парткод: | 6LA04323000 |
| Деталь: | G05H-45/G05S-15 |
| Парткод: | 6LA04324000 |
| Деталь: | ASYS-MOT-TRAY390 |
| Парткод: | 6LE05729000 |
| Деталь: | GEAR-05H064-08 |
| Парткод: | 6LA04255000 |
| Деталь: | PLY-Z29-Z25-3M |
| Парткод: | 4401783350 |
| Деталь: | GEAR-1.0-Z28 |
| Парткод: | 4401783330 |
| Деталь: | GEAR-10S034-06 |
| Парткод: | 44201683000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | BELT-3M-Z103 |
| Парткод: | 4401783700 |
| Деталь: | COVER-IN-TRU |
| Парткод: | 6LE08805000 |
| Деталь: | DUCT-TRU |
| Парткод: | 6LA02792000 |
| Деталь: | SEAL-TRU-CR |
| Парткод: | 6LE16206000 |
| Деталь: | EDS-1717U |
| Парткод: | F0-00047000 |
| Деталь: | PL-EARTH-C-SUB |
| Парткод: | 6LA02793000 |
| Деталь: | HRNS-HVT-TR2-340 |
| Парткод: | 6LA07396000 |
| Деталь: | ASYS-BRKT-LNK-F |
| Парткод: | 6LA02812000 |
| Деталь: | ASYS-BRKT-LNK-H |
| Парткод: | 6LA02815000 |
| Деталь: | PLATE-LINK-H |
| Парткод: | 4406338380 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | SHAFT-HANDLE-TRU |
| Парткод: | 6LE08828000 |
| Деталь: | CAM-F-TRU |
| Парткод: | 6LA02804000 |
| Деталь: | BUSH-8 |
| Парткод: | 4400802080 |
| Деталь: | SCREW-STOP-H |
| Парткод: | 4406338130 |
| Деталь: | COLLAR-STP-HDL |
| Парткод: | 4406339490 |
| Деталь: | SCREW-HANDLE |
| Парткод: | 4406339500 |
| Деталь: | LBL-ADU-OPEN |
| Парткод: | 6LE08818000 |
| Деталь: | HANDLE-TRU-390 |
| Парткод: | 6LE08801000 |
| Деталь: | SPE080-100-0530 |
| Парткод: | 4406338300 |
| Деталь: | SCREW-RAIL-TRU |
| Парткод: | 6LA02823000 |
| Деталь: | LBL-W-HOT-STAY-390 |
| Парткод: | 6LE08831000 |
| Деталь: | EDS-1 |
| Парткод: | F0-00045000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | S/HEX-M48-NI |
| Парткод: | 6LA08905000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | BRKT-DH-L-340 |
| Парткод: | 6LA02845000 |
| Деталь: | HF05N132 |
| Парткод: | E0-05780000 |
| Деталь: | HF05N442 |
| Парткод: | E0-05781000 |
| Деталь: | HRNS-DHT-L-340 |
| Парткод: | 6LA07432000 |
| Деталь: | PWA-F-FUS-390UE |
| Парткод: | 6LE09411100 |
| Деталь: | THRMST-CS-7SA |
| Парткод: | 6LE71198000 |
| Деталь: | SKB-80MZ |
| Парткод: | F0-00021000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | SPLSN-4U |
| Парткод: | F0-00340000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | S/TPS/BID-3X6-NI |
| Парткод: | X0-00676000 |
| Деталь: | WH-TRY-608 |
| Парткод: | 6LE04826000 |
| Деталь: | BASE-T |
| Парткод: | 6LE04810000 |
| Деталь: | BASE-T-SUB93 |
| Парткод: | 6LA15902000 |
| Деталь: | HLDR-T-SNS |
| Парткод: | 6LA09187000 |
| Деталь: | COV-T |
| Парткод: | 6LE04811000 |
| Деталь: | GEAR-T-76 |
| Парткод: | 6LA09178000 |
| Деталь: | GID-T-F93 |
| Парткод: | 6LA15901000 |
| Деталь: | GID-T-R93 |
| Парткод: | 6LA15900000 |
| Деталь: | LBL-T-SIZE |
| Парткод: | 6LA09400000 |
| Деталь: | LEVER-SNR-T |
| Парткод: | 6LA09068000 |
| Деталь: | MGT-T-SPC93 |
| Парткод: | 6LE04831000 |
| Деталь: | PBA-VR93 |
| Парткод: | 6LE04820000 |
| Деталь: | RACK-T |
| Парткод: | 6LA09208000 |
| Деталь: | SHEET-STY-LOWER |
| Парткод: | 6LA09406000 |
| Деталь: | SPACER-TRAY-PL |
| Парткод: | 6LA09239000 |
| Деталь: | SPL-PLT-T |
| Парткод: | 6LA09286000 |
| Деталь: | LBL-T-LIMIT |
| Парткод: | 6LA09446000 |
| Деталь: | SNS-TLP1241 |
| Парткод: | 6LE00883000 |
| Деталь: | SCRW-3008FNBB |
| Парткод: | 6LA09011000 |
| Деталь: | FLNG-FLY-390 |
| Парткод: | 6LE16210000 |
| Деталь: | K-FLG-DRUM-F |
| Парткод: | 6LA02225000 |
| Деталь: | ASY-FLG-DRUM-R |
| Парткод: | 6LA02228000 |
| Деталь: | BRKT-JOINT-FLG |
| Парткод: | 4406331570 |
| Деталь: | SPL030-S304-DRV |
| Парткод: | 4406331580 |
| Деталь: | BRKT-DRV-DRUM |
| Парткод: | 6LA02266000 |
| Деталь: | K-HSG-SFT-BRG |
| Парткод: | 6LA02267000 |
| Деталь: | SHAFT-DRUM-20-C |
| Парткод: | 6LA02269000 |
| Деталь: | CLR-COUP-SUB-C |
| Парткод: | 4406331740 |
| Деталь: | SPC-235-180-300 |
| Парткод: | 4406331750 |
| Деталь: | CPG-DRUM-300 |
| Парткод: | 4406331650 |
| Деталь: | ASYS-PLY/T-3GT056 |
| Парткод: | 6LE04137000 |
| Деталь: | BLT/T-3GT276-60 |
| Парткод: | 4406331240 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | MOTRS-DRUM-390 |
| Парткод: | 6LE09158000 |
| Деталь: | BRKT-MOT-DRUM-390 |
| Парткод: | 6LE04117000 |
| Деталь: | PWA-F-MOT-DRTM-390 |
| Парткод: | 6LE09183000 |
| Деталь: | S/HEX-M48-NI |
| Парткод: | 6LA08905000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/PAN-M4X16-NI |
| Парткод: | X0-02004000 |
| Деталь: | RR/C/EXT-20-B |
| Парткод: | X0-01241000 |
| Деталь: | RR/C/EXT-17-B |
| Парткод: | X0-01240000 |
| Деталь: | S/PAN/SWWP-M4X10-NI |
| Парткод: | X0-01981000 |
| Деталь: | WH-SIO-EXIT-SNS |
| Парткод: | 6LA09150000 |
| Деталь: | BLT-248-S2M-4 |
| Парткод: | 6LA09049000 |
| Деталь: | BRKT-S-SNS-OW |
| Парткод: | 6LA09276000 |
| Деталь: | BUSH6 |
| Парткод: | 6LA09062000 |
| Деталь: | ROLLER-SB-EXIT |
| Парткод: | 6LA09364000 |
| Деталь: | BUSH8 |
| Парткод: | 6LA09433000 |
| Деталь: | CLIP4 |
| Парткод: | 6LA09074000 |
| Деталь: | CLIP5 |
| Парткод: | 6LA09057000 |
| Деталь: | FLP-EXIT-S-N |
| Парткод: | 6LA09469000 |
| Деталь: | FLP-S-OW-C |
| Парткод: | 6LA09199000 |
| Деталь: | FLP-S-OW-F |
| Парткод: | 6LA09198000 |
| Деталь: | FLP-S-OW-R |
| Парткод: | 6LA09200000 |
| Деталь: | FOOT-S-RIGHT |
| Парткод: | 6LA09225000 |
| Деталь: | MYLAR-SB-LEXSNS |
| Парткод: | 6LA09394000 |
| Деталь: | GUID-S-EXIT |
| Парткод: | 6LA09259000 |
| Деталь: | GUID-S-SB |
| Парткод: | 6LA09193000 |
| Деталь: | HLDR-S-SNS-EX |
| Парткод: | 6LA09196000 |
| Деталь: | LVR-R-SOL-LS |
| Парткод: | 6LA09184000 |
| Деталь: | LVR-S-SNS-EX |
| Парткод: | 6LA09197000 |
| Деталь: | PLY/T-S2M-17 |
| Парткод: | 6LA09206000 |
| Деталь: | PLY/T-S2M-17-OW |
| Парткод: | 6LA09207000 |
| Деталь: | PLY/T-S2M-22 |
| Парткод: | 6LA09205000 |
| Деталь: | FLANGE-S |
| Парткод: | 6LA09055000 |
| Деталь: | RMLC-05T-V0 |
| Парткод: | 6LA09031000 |
| Деталь: | ROLLER-S-C |
| Парткод: | 6LA09341000 |
| Деталь: | ROLLER-EXIT |
| Парткод: | 6LA09343000 |
| Деталь: | ROLLER-S-SSB |
| Парткод: | 6LA09342000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA09399000 |
| Деталь: | SCR-M3X6ITSR-NI |
| Парткод: | 6LA09396000 |
| Деталь: | SENSOR |
| Парткод: | 6LE00886000 |
| Деталь: | SPE-R-LSF |
| Парткод: | 6LA09353000 |
| Деталь: | SPL-S-SNS-EXIT |
| Парткод: | 6LA09371000 |
| Деталь: | STAY-S-RIGHT |
| Парткод: | 6LA09277000 |
| Деталь: | CLIP-3KL |
| Парткод: | 6LA09059000 |
| Деталь: | GUID-SB-LEXIT |
| Парткод: | 6LA09288000 |
| Деталь: | FLP-R-LS |
| Парткод: | 6LA09347000 |
| Деталь: | ERR050SK |
| Парткод: | 6LA09034000 |
| Деталь: | ERR070SK |
| Парткод: | 6LA09035000 |
| Деталь: | RSG-100 |
| Парткод: | 6LA09026000 |
| Деталь: | KI-100 |
| Парткод: | 6LA09020000 |
| Деталь: | SNS-TLP1241 |
| Парткод: | 6LE00883000 |
| Деталь: | SCRW-3005FNWS |
| Парткод: | 6LA09009000 |
| Деталь: | SCRW-3008FNSW |
| Парткод: | 6LA09012000 |
| Деталь: | SCRW-3008FNBB |
| Парткод: | 6LA09011000 |
| Деталь: | BUSH-06 |
| Парткод: | 6LA09017000 |
| Деталь: | BUSH-08 |
| Парткод: | 6LA09016000 |
| Деталь: | BKT-FEED-LENSNS |
| Парткод: | 6LA09280000 |
| Деталь: | BRKT-FEED-RET |
| Парткод: | 6LA09262000 |
| Деталь: | BRSH-LEX-F |
| Парткод: | 6LA15897000 |
| Деталь: | BUSH6 |
| Парткод: | 6LA09062000 |
| Деталь: | CLIP4 |
| Парткод: | 6LA09074000 |
| Деталь: | CLIP5 |
| Парткод: | 6LA09057000 |
| Деталь: | COV-K-RET |
| Парткод: | 6LE04809000 |
| Деталь: | CVR-FEED-RET-SP |
| Парткод: | 6LA09241000 |
| Деталь: | GEAR-0.8-16 |
| Парткод: | 6LA09432000 |
| Деталь: | GEAR-0.8-26 |
| Парткод: | 6LA09431000 |
| Деталь: | GEAR-080-50 |
| Парткод: | 6LA09181000 |
| Деталь: | GID-K-UNDER |
| Парткод: | 6LE04806000 |
| Деталь: | CLIP-4KL |
| Парткод: | 6LA09053000 |
| Деталь: | LVR-FEED-REL |
| Парткод: | 6LA09176000 |
| Деталь: | MYLAR-L-SNS |
| Парткод: | 6LA09358000 |
| Деталь: | MYLAR-RGST |
| Парткод: | 6LA09387000 |
| Деталь: | CLMP-MSBS-1207 |
| Парткод: | 6LA09027000 |
| Деталь: | PLT-FEED-PICK |
| Парткод: | 6LA09161000 |
| Деталь: | PLY/T-S2M-24-10 |
| Парткод: | 6LA09180000 |
| Деталь: | ROLLER-RGST |
| Парткод: | 6LA09340000 |
| Деталь: | SEP-ROLLER |
| Парткод: | 6LA09005000 |
| Деталь: | ASYS-RUB-PRE |
| Парткод: | 6LA09460000 |
| Деталь: | LEVER-RELEASE |
| Парткод: | 6LA09166000 |
| Деталь: | SFT-FEED-RET-1 |
| Парткод: | 6LA09311000 |
| Деталь: | SFT-FEED-RET-2 |
| Парткод: | 6LA09312000 |
| Деталь: | SHEET-PICK |
| Парткод: | 6LA09346000 |
| Деталь: | SHEET-RET-SP |
| Парткод: | 6LA09359000 |
| Деталь: | SHEET-STY-LOWER |
| Парткод: | 6LA09406000 |
| Деталь: | SENSOR |
| Парткод: | 6LE00886000 |
| Деталь: | SPC-FEED-RET-S |
| Парткод: | 6LA09355000 |
| Деталь: | SPL-FEED-RTD-P |
| Парткод: | 6LA09281000 |
| Деталь: | CUSH-PICK |
| Парткод: | 6LA09345000 |
| Деталь: | STAY-FEED-UNDER |
| Парткод: | 6LA09257000 |
| Деталь: | SNS-TLP1241 |
| Парткод: | 6LE00883000 |
| Деталь: | TQL-K |
| Парткод: | 6LA09404000 |
| Деталь: | GEAR-30 |
| Парткод: | 6LA09054000 |
| Деталь: | BUSH-10 |
| Парткод: | 6LA09063000 |
| Деталь: | BUSH-08 |
| Парткод: | 6LA09016000 |
| Деталь: | CLIP-3KL |
| Парткод: | 6LA09059000 |
| Деталь: | WH-LENS-608 |
| Парткод: | 6LE04829000 |
| Деталь: | HOLDER-ST-N |
| Парткод: | 6LA09451000 |
| Деталь: | MLR-COVER-K-RET |
| Парткод: | 6LA09134000 |
| Деталь: | WH-SOL-608 |
| Парткод: | 6LE04825000 |
| Деталь: | ERR050SK |
| Парткод: | 6LA09034000 |
| Деталь: | ERR070SK |
| Парткод: | 6LA09035000 |
| Деталь: | SCRW-3010FNBB |
| Парткод: | 6LA09013000 |
| Деталь: | SCRW-M3-3.2 |
| Парткод: | 6LA09434000 |
| Деталь: | RSG-100 |
| Парткод: | 6LA09026000 |
| Деталь: | SCRW-3008FNSW |
| Парткод: | 6LA09012000 |
| Деталь: | HPIN20/10SCH |
| Парткод: | 6LA09038000 |
| Деталь: | HPIN20/12SCH |
| Парткод: | 6LA09039000 |
| Деталь: | HPIN20/08SCH |
| Парткод: | 6LA09037000 |
| Деталь: | BUSH-06 |
| Парткод: | 6LA09007000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA09399000 |
| Деталь: | HR-6000-L |
| Парткод: | 6LE19371000 |
| Деталь: | HR-6000-U |
| Парткод: | 6LE19370000 |
| Деталь: | STUD-ARM-PS-390 |
| Парткод: | 6LE06600000 |
| Деталь: | HLDR-PRESS |
| Парткод: | 4401758440 |
| Деталь: | BRG-6905ZZ |
| Парткод: | 4406323720 |
| Деталь: | COLER-BRG-HR |
| Парткод: | 4401902550 |
| Деталь: | BRKT-IH-R |
| Парткод: | 6LA05201000 |
| Деталь: | BRG-6812ZZ |
| Парткод: | 6LA05255000 |
| Деталь: | CRR/S600SKFB |
| Парткод: | 6LA05280000 |
| Деталь: | GEAR-10S072-60 |
| Парткод: | 6LA05260000 |
| Деталь: | ASYS-ARM-PRESS-R |
| Парткод: | 6LE06700000 |
| Деталь: | ASYS-ARM-PRESS-F |
| Парткод: | 6LE06699000 |
| Деталь: | WAS-15-45-FUS |
| Парткод: | 4401759260 |
| Деталь: | ASY-COIL-IH390-100 |
| Парткод: | 6LE06680000 |
| Деталь: | ASY-COIL-IH390-200 |
| Парткод: | 6LE06680100 |
| Деталь: | S/FPAN-M4X8-NI |
| Парткод: | X0-00486000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/PAN-M4X25-NI |
| Парткод: | X0-02006000 |
| Деталь: | S/PAN-M4X6-NC |
| Парткод: | X0-01528000 |
| Деталь: | SCREW-FUSER-M4 |
| Парткод: | 4401759180 |
| Деталь: | SCREW-M4-D6-6.5 |
| Парткод: | 4406324750 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 6LA08937000 |
| Деталь: | SCREW-M4-D8-HND |
| Парткод: | 6LA05274000 |
| Деталь: | SCREW-FUSER-M4B-N |
| Парткод: | 6LA36437000 |
| Деталь: | SPC-PRESS-H390 |
| Парткод: | 6LE06698000 |
| Деталь: | SPC-PRESS-L390 |
| Парткод: | 6LE06695000 |
| Деталь: | ASYS-GEAR-10H019-F |
| Парткод: | 6LE04536000 |
| Деталь: | BUSH-GAP-DEV-RE |
| Парткод: | 6LA02423000 |
| Деталь: | SPRING-RE-340 |
| Парткод: | 6LA02448000 |
| Деталь: | ROLLER-RE |
| Парткод: | 6LA02422000 |
| Деталь: | SHLD-ROL-RE-F |
| Парткод: | 6LA02428000 |
| Деталь: | SHLD-ROL-RE-R |
| Парткод: | 6LA02429000 |
| Деталь: | GG08S030/08S016 |
| Парткод: | 6LA02451000 |
| Деталь: | GEAR-08S020-IR |
| Парткод: | 6LA02452000 |
| Деталь: | GEAR-08S020-RE |
| Парткод: | 6LA02453000 |
| Деталь: | ROLLER-GUIDE-6 |
| Парткод: | 6LA02409000 |
| Деталь: | Roller-Guide |
| Парткод: | 4406332850 |
| Деталь: | ROLLER-GUIDE-RL |
| Парткод: | 4406333300 |
| Деталь: | PLT-BIAS-MG-340 |
| Парткод: | 6LA02460000 |
| Деталь: | PIN-2-10 |
| Парткод: | 4408256620 |
| Деталь: | ASYS-PLT-DEV-F-390 |
| Парткод: | 6LE04504000 |
| Деталь: | K-PLT-DEV-F-340 |
| Парткод: | 6LA02403000 |
| Деталь: | BRG-626-DD-NXR |
| Парткод: | 4407637290 |
| Деталь: | TERM-BIAS-DEV |
| Парткод: | 4406333080 |
| Деталь: | PLT-BIAS-DEV |
| Парткод: | 4406333090 |
| Деталь: | HRNS-BIAS-MG-340 |
| Парткод: | 6LA07416000 |
| Деталь: | GEAR-10H027-PDR |
| Парткод: | 4406332640 |
| Деталь: | ASYS-DUCT-DEV-390 |
| Парткод: | 6LE04543000 |
| Деталь: | SNSR-ATC-390 |
| Парткод: | 6LE09165000 |
| Деталь: | SEAL-SIDE-DR-F |
| Парткод: | 6LA02425000 |
| Деталь: | SEAL-SIDE-DR-R |
| Парткод: | 6LA02426000 |
| Деталь: | SEAL-SIDE-D-FLT |
| Парткод: | 4406333580 |
| Деталь: | K-DOCTOR-MG-TR |
| Парткод: | 4406333260 |
| Деталь: | T18S |
| Парткод: | F0-00017000 |
| Деталь: | ASYS-BUSH-PDL-R |
| Парткод: | 6LA02414000 |
| Деталь: | DETECTOR-DEV-390 |
| Парткод: | 6LE04520000 |
| Деталь: | ASYS-BRKT-DEV-RE-390 |
| Парткод: | 6LE04502000 |
| Деталь: | K-BRKT-DEV-RE |
| Парткод: | 6LA02440000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/PAN/SWWP-M3X6-BSNI |
| Парткод: | X0-00067000 |
| Деталь: | S/BID-M3X4-BSNI |
| Парткод: | X0-01724000 |
| Деталь: | S/TSP/PAN-3X6-ZU3 |
| Парткод: | X0-02056000 |
| Деталь: | GEAR-10H025-390 |
| Парткод: | 6LE04512000 |
| Деталь: | GEAR-10H031-PDR |
| Парткод: | 4406332630 |
| Деталь: | ASYS-PLT-DEV-R-390 |
| Парткод: | 6LE04514000 |
| Деталь: | K-PLT-DEV-R-340 |
| Парткод: | 6LA02405000 |
| Деталь: | ASYS-GEAR-10H023-R |
| Парткод: | 6LE04535000 |
| Деталь: | ASYS-GEAR-10H020-R |
| Парткод: | 6LE04538000 |
| Деталь: | BRKT-COV-BELT |
| Парткод: | 6LA93658000 |
| Деталь: | LBL-P-SET-TRY-L |
| Парткод: | 6LA93863000 |
| Деталь: | K-GUIDE-SIDE-RF |
| Парткод: | 6LA15091000 |
| Деталь: | BRKT-DAMPER |
| Парткод: | 6LA93680000 |
| Деталь: | OIL-DAMPER-390 |
| Парткод: | 6LE03901000 |
| Деталь: | BRKT-BELT-STOP |
| Парткод: | 6LA93679000 |
| Деталь: | GEAR-DUMP-Z18 |
| Парткод: | 6LA93797000 |
| Деталь: | PLY-BRKT |
| Парткод: | 6LA93798000 |
| Деталь: | BUSH-8X12X8F |
| Парткод: | 6LA65698000 |
| Деталь: | BLT.SY-426-3GT |
| Парткод: | 6LA14353000 |
| Деталь: | PLY/T-3-020 |
| Парткод: | 6LA93775000 |
| Деталь: | BRKT-ROL-STOP |
| Парткод: | 6LA04814000 |
| Деталь: | PLY-TRAY-ROL |
| Парткод: | 6LA93774000 |
| Деталь: | TRAY-TAN-LCF |
| Парткод: | 6LA04801000 |
| Деталь: | PLT-BALANCER |
| Парткод: | 6LA93713000 |
| Деталь: | PAD-TRAY |
| Парткод: | 6LA04847000 |
| Деталь: | LBL-P-SET-TRY-R |
| Парткод: | 6LA93864000 |
| Деталь: | K-FENCE-SIDE-R-F |
| Парткод: | 6LA04835000 |
| Деталь: | FENCE-SIDE-R-R |
| Парткод: | 6LA04803000 |
| Деталь: | K-GUIDE-SIDE-RR-N |
| Парткод: | 6LA15092000 |
| Деталь: | K-SFT-TRAY |
| Парткод: | 6LA04815000 |
| Деталь: | MDC-SLIDER-390 |
| Парткод: | 6LE09179000 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 6LA08931000 |
| Деталь: | K-CST-TLCF |
| Парткод: | 6LA04860000 |
| Деталь: | HRNS-TLCF-IN-390 |
| Парткод: | 6LE09483000 |
| Деталь: | BRKT-MOT-SLID |
| Парткод: | 6LA04818000 |
| Деталь: | GEAR-10H033-08 |
| Парткод: | 6LA04821000 |
| Деталь: | BRKT-CAH-T-LCF |
| Парткод: | 6LA04822000 |
| Деталь: | SPL-LEVER-LCF |
| Парткод: | 6LA04824000 |
| Деталь: | ASYS-LOCK-TNDM |
| Парткод: | 6LA04841000 |
| Деталь: | GEAR-MOT-Z33 |
| Парткод: | 6LA04829000 |
| Деталь: | MYLAR-BRKT-ROL |
| Парткод: | 6LA04853000 |
| Деталь: | STOP-RING-8 |
| Парткод: | 4400336190 |
| Деталь: | LBL-P-LIMIT |
| Парткод: | 6LA93862000 |
| Деталь: | SPL-EARTH-LCF |
| Парткод: | 6LA04809000 |
| Деталь: | BRKT-COV-P-END |
| Парткод: | 6LA93656000 |
| Деталь: | PHD-ACT |
| Парткод: | 6LE03902000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/HEX-M36-NI |
| Парткод: | 6LA08900000 |
| Деталь: | P/PRL/AH7-3X14-SS |
| Парткод: | X0-01169000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | S/PAN/SWWP-M3X8-NI |
| Парткод: | X0-00077000 |
| Деталь: | S/TPS/HEX-312-NI |
| Парткод: | 6LA08911000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/TPP/HEX-3X10-NI |
| Парткод: | 6LA08918000 |
| Деталь: | BRKT-CAM-MAIN-390 |
| Парткод: | 6LE08814000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | TLP1255(C8) |
| Парткод: | C0-10814000 |
| Деталь: | STUD-CAM |
| Парткод: | 4406339670 |
| Деталь: | GG08H028/08S014 |
| Парткод: | 4406339680 |
| Деталь: | STOP-RING-6-5 |
| Парткод: | 4407972860 |
| Деталь: | MOTRD-CAM-390 |
| Парткод: | 6LE09171000 |
| Деталь: | SHAFT-CAM |
| Парткод: | 4406339640 |
| Деталь: | P/PRL/AH7-2X8-SS |
| Парткод: | X0-00979000 |
| Деталь: | GEAR-08S035-06 |
| Парткод: | 4406339650 |
| Деталь: | ACTR-CAM |
| Парткод: | 4406339660 |
| Деталь: | BUSH-6-POM |
| Парткод: | 44201492000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | CAM-LEVER-R |
| Парткод: | 4406339630 |
| Деталь: | HRNS-TRU-CAM-390 |
| Парткод: | 6LE09260000 |
| Деталь: | ASYS-BASE-D-TRU |
| Парткод: | 6LA03005000 |
| Деталь: | ASYS-DRV-J-TRU |
| Парткод: | 6LA03010000 |
| Деталь: | K-GP10H24/3GT21 |
| Парткод: | 4406340090 |
| Деталь: | BLT/T-3GT180-60 |
| Парткод: | 4401906540 |
| Деталь: | BRKT-STUD-DRV |
| Парткод: | 6LA03015000 |
| Деталь: | K-GR-10H024-08B |
| Парткод: | 4406340060 |
| Деталь: | IDLER-DRV-TRU |
| Парткод: | 4406339970 |
| Деталь: | BRKT-DRIVE-CAP |
| Парткод: | 6LA03013000 |
| Деталь: | CAP-IDLE-DRV |
| Парткод: | 4406339980 |
| Деталь: | MOTRS-TRU-390 |
| Парткод: | 6LE09170000 |
| Деталь: | BRKT-MOT-TRU-390 |
| Парткод: | 6LE08815000 |
| Деталь: | BUSH-BRKT-SCAN |
| Парткод: | 4408302680 |
| Деталь: | SPE100-100-0335 |
| Парткод: | 4406340030 |
| Деталь: | S/PAN/SWWP-M3X6-NI |
| Парткод: | X0-00060000 |
| Деталь: | S/PAN-M2.6X2.5-NI |
| Парткод: | X0-02270000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/TPS/HEX-412-NI |
| Парткод: | 6LA08915000 |
| Деталь: | CARRIGE-2-390 |
| Парткод: | 6LE08101000 |
| Деталь: | FOOT-CRG2-310 |
| Парткод: | 4406516200 |
| Деталь: | CUSH-CRG2 |
| Парткод: | 6LA01919000 |
| Деталь: | ASYS-BKT-PLY-F-C2 |
| Парткод: | 6LA67394000 |
| Деталь: | ASYS-BKT-PLY-R-C2 |
| Парткод: | 6LA67395000 |
| Деталь: | GUIDE-WH-CRG2-340 |
| Парткод: | 6LA14354000 |
| Деталь: | S/PAN/SWWP-M3X8-NI |
| Парткод: | X0-00077000 |
| Деталь: | S/TPS/HEX-36-NI |
| Парткод: | 6LA08908000 |
| Деталь: | S/TPS/BID-3X6-ZU3 |
| Парткод: | X0-02069000 |
| Деталь: | ASYS-FRM-TRANS |
| Парткод: | 6LE05701000 |
| Деталь: | MOTRS-MT-390 |
| Парткод: | 6LE09520000 |
| Деталь: | SHAFT-TRANS |
| Парткод: | 6LE05703000 |
| Деталь: | BRKT-ACTR-TRANS |
| Парткод: | 6LE05706000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | ACTUATOR-TRANS |
| Парткод: | 6LE05704000 |
| Деталь: | SPG-T-TRANS-ACTR |
| Парткод: | 6LE05705000 |
| Деталь: | SPL-GUIDE-ROL2 |
| Парткод: | 6LA03543000 |
| Деталь: | KGLS-6RT |
| Парткод: | F0-00226000 |
| Деталь: | PWA-F-MOT2-390MT |
| Парткод: | 6LE09140000 |
| Деталь: | HRNS-MIDTR-390 |
| Парткод: | 6LE09237000 |
| Деталь: | GUIDE-ADU-EX-L1 |
| Парткод: | 6LA03557000 |
| Деталь: | GUIDE-ADU-EX-L2 |
| Парткод: | 6LA03558000 |
| Деталь: | K-BKT-JNT-TRANS |
| Парткод: | 6LA03584000 |
| Деталь: | SPRING-TRANS-R |
| Парткод: | 6LA03581000 |
| Деталь: | ROLL-TRANS-390 |
| Парткод: | 6LE05758000 |
| Деталь: | BRG-688ZZNR |
| Парткод: | 4408510800 |
| Деталь: | PLY/T-S2M-28-08 |
| Парткод: | 6LA04720000 |
| Деталь: | BLT_SY-S2M-124-6 |
| Парткод: | 6LE05713000 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | LWS-0711Z |
| Парткод: | F0-00736000 |
| Деталь: | GUIDE-ROL-T-L-390 |
| Парткод: | 6LE05717000 |
| Деталь: | SPL-GUIDE-ROL1-390 |
| Парткод: | 6LE05746000 |
| Деталь: | K-VARIST-390 |
| Парткод: | 6LE09175000 |
| Деталь: | SUPPORT-GUIDE |
| Парткод: | 6LE05712000 |
| Деталь: | SUPPORT-GUIDE-P |
| Парткод: | 4401772280 |
| Деталь: | GEAR-10S021-06 |
| Парткод: | 6LA03552000 |
| Деталь: | GEAR-10S034-08 |
| Парткод: | 6LA03553000 |
| Деталь: | ASYS-BRKT-TRANS-G |
| Парткод: | 6LE05708000 |
| Деталь: | CAP-STUD-SFB |
| Парткод: | 6LA03570000 |
| Деталь: | SPC-064-060-0110 |
| Парткод: | 6LA03576000 |
| Деталь: | SPC-079-070-0110 |
| Парткод: | 6LA03575000 |
| Деталь: | BRKT-HOLD-SP |
| Парткод: | 6LA03578000 |
| Деталь: | SHAFT-TRANS-390 |
| Парткод: | 6LE05759000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | S/HEX-M36-NI |
| Парткод: | 6LA08900000 |
| Деталь: | RR/E-2-SS |
| Парткод: | X0-00963000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | K-BRKT-FUS-MOT |
| Парткод: | 6LA05484000 |
| Деталь: | K-GR10S23/05H50 |
| Парткод: | 4406325850 |
| Деталь: | SPC-075-055-200 |
| Парткод: | 4363260910 |
| Деталь: | COVER-FUS-GEAR |
| Парткод: | 6LA05500000 |
| Деталь: | MOTRD-HTR-390 |
| Парткод: | 6LE09157000 |
| Деталь: | GEAR-5H50_P3GT17-6 |
| Парткод: | 6LE03100000 |
| Деталь: | HRNS-LGC-FUS-390 |
| Парткод: | 6LE09598000 |
| Деталь: | SPC068-080-160 |
| Парткод: | 6LA14468000 |
| Деталь: | AGX206F |
| Парткод: | E0-08333000 |
| Деталь: | STUD-ADU-CUP |
| Парткод: | 6LA05488000 |
| Деталь: | BLT_SY-3GT-339-6 |
| Парткод: | 6LE03101000 |
| Деталь: | PLY/T-3GT021-06 |
| Парткод: | 6LA05494000 |
| Деталь: | SPLSN-4U |
| Парткод: | F0-00340000 |
| Деталь: | HL-28-0-V0 |
| Парткод: | F0-00838000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | FAND-8025-390 |
| Парткод: | 6LE09166000 |
| Деталь: | ASYS-DUCT-FUS-PWA-390 |
| Парткод: | 6LE06660000 |
| Деталь: | COV-PWA-IH |
| Парткод: | 6LE06624000 |
| Деталь: | LBL-W-HOT-340 |
| Парткод: | 6LA06571000 |
| Деталь: | PLATE-COVER-IH |
| Парткод: | 6LE06691000 |
| Деталь: | BRKT-IH-FAN |
| Парткод: | 6LA05538000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | LWS-2111Z |
| Парткод: | F0-01299000 |
| Деталь: | LBL-FUS-TNR-IN |
| Парткод: | 6LE13137000 |
| Деталь: | BRKT-IH-GND |
| Парткод: | 6LA05537000 |
| Деталь: | ASYS-DUCT-FUS-L-390 |
| Парткод: | 6LE06648000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/TPS/HEX/R-M4X12 |
| Парткод: | 6LA14330000 |
| Деталь: | SCREW-D4-18-M3 |
| Парткод: | 4406326040 |
| Деталь: | SCREW-BKT-DEV |
| Парткод: | 6LA08937000 |
| Деталь: | SCREW-M3-D4-7-ZU3 |
| Парткод: | 6LE06667000 |
| Деталь: | SCREW-CON-DEV-V |
| Парткод: | 6LA08933000 |
| Деталь: | S/HEX-M48-NI |
| Парткод: | 6LA08905000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | S/HEX-M36-NI |
| Парткод: | 6LA08900000 |
| Деталь: | S/PAN/SWWP-M4X8-NI |
| Парткод: | X0-00164000 |
| Деталь: | S/BID-M3X8-NI |
| Парткод: | X0-00434000 |
| Деталь: | S/TPS/HEX-410-NI |
| Парткод: | 6LA08914000 |
| Деталь: | ASYS-PS-IH-390U |
| Парткод: | 6LE06661000 |
| Деталь: | ASYS-PS-IH-390E |
| Парткод: | 6LE06661200 |
| Деталь: | ASYS-PS-IH-390S |
| Парткод: | 6LE06661300 |
| Деталь: | SHIELD-IH |
| Парткод: | 6LE06692000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | SCR-M48ITSR-NI |
| Парткод: | 6LA08934000 |
| Деталь: | SPS-3U |
| Парткод: | F0-00027000 |
| Деталь: | SPLSN-6U |
| Парткод: | F0-00342000 |
| Деталь: | LWS-1211Z |
| Парткод: | F0-01243000 |
| Деталь: | LWS-2111Z |
| Парткод: | F0-01299000 |
| Деталь: | EDS-1717U |
| Парткод: | F0-00047000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | BUSH-KG-016L-SYS |
| Парткод: | 6LE05412000 |
| Деталь: | SPLSN-8U |
| Парткод: | F0-00343000 |
| Деталь: | BD/W-TWS-3027 |
| Парткод: | 4406509170 |
| Деталь: | BRKT-HINGE-BYP |
| Парткод: | 6LA04747000 |
| Деталь: | HRNS-PLG-SYS-390 |
| Парткод: | 6LE09208000 |
| Деталь: | HRNS-HVT-M-390 |
| Парткод: | 6LE09118000 |
| Деталь: | HRNS-HVT-TR-390 |
| Парткод: | 6LE09119000 |
| Деталь: | K-JOINT-RGT |
| Парткод: | 4406349900 |
| Деталь: | K-BKT-HINGE-FED |
| Парткод: | 6LA04139000 |
| Деталь: | SEAL-FRAME-R |
| Парткод: | 6LA01386000 |
| Деталь: | BRKT-DRIVE-MID |
| Парткод: | 6LA04261000 |
| Деталь: | SHAFT-DRIVE-MID |
| Парткод: | 6LA04262000 |
| Деталь: | BUSH-6-GCB |
| Парткод: | 4407734980 |
| Деталь: | P/PRL/AH7-2X12-SS |
| Парткод: | X0-01526000 |
| Деталь: | GEAR-10S035-06 |
| Парткод: | 6LA04263000 |
| Деталь: | GP1A73ARJ00F |
| Парткод: | C0-10813000 |
| Деталь: | OCB-375 |
| Парткод: | F0-00370000 |
| Деталь: | GSKT-10-10-50 |
| Парткод: | 6LA01199000 |
| Деталь: | HRNS-HVT-BRS-390 |
| Парткод: | 6LE09116000 |
| Деталь: | HRNS-LGC-REV-390 |
| Парткод: | 6LE09188000 |
| Деталь: | HRNS-LGC-DEVM-390 |
| Парткод: | 6LE09278000 |
| Деталь: | BRKT-HINGE-STOP-390 |
| Парткод: | 6LE05763000 |
| Деталь: | SUPPORT-GUIDE-P |
| Парткод: | 4401772280 |
| Деталь: | K-JNT-GUIDE-U-S |
| Парткод: | 6LA03350000 |
| Деталь: | BRKT-FUS-DRV |
| Парткод: | 6LA05330000 |
| Деталь: | BRKT-HINGE-STOP-SUB |
| Парткод: | 6LE05764000 |
| Деталь: | S/TPS/HEX-48-NI |
| Парткод: | 6LA08913000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/TPS/HEX-38-NI |
| Парткод: | 6LA08909000 |
| Деталь: | EMT-4N |
| Парткод: | F0-00119000 |
| Деталь: | S/BID-M4X6-NC |
| Парткод: | X0-01285000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA08935000 |
| Деталь: | ASY-HRNS-CST-390JU |
| Парткод: | 6LE09413000 |
| Деталь: | ASY-HRNS-CST-390 |
| Парткод: | 6LE09412000 |
| Деталь: | HRNS-LGC-BTM-340J |
| Парткод: | 6LA07406000 |
| Деталь: | HRNS-LGC-BTM-340 |
| Парткод: | 6LA07340000 |
| Деталь: | ARM-S-LATCH |
| Парткод: | 6LA09329000 |
| Деталь: | WH-RD-SNS-551 |
| Парткод: | 6LA09148000 |
| Деталь: | ASY-L-SOL-SUB |
| Парткод: | 6LA09098000 |
| Деталь: | ASY-EST-SOL-SUB |
| Парткод: | 6LA09100000 |
| Деталь: | ASYS-SB-IDLER |
| Парткод: | 6LA09096000 |
| Деталь: | BRKT-R-SOL-LS |
| Парткод: | 6LA09268000 |
| Деталь: | BRKT-SB-RELEASE |
| Парткод: | 6LA09307000 |
| Деталь: | BRKT-SB-RELEAS |
| Парткод: | 6LA09291000 |
| Деталь: | BUSH6 |
| Парткод: | 6LA09062000 |
| Деталь: | CLIP4 |
| Парткод: | 6LA09074000 |
| Деталь: | CVR-S-LATCH |
| Парткод: | 6LA09222000 |
| Деталь: | DUCT-F |
| Парткод: | 6LA09242000 |
| Деталь: | HLDR-DF-SNS |
| Парткод: | 6LA09230000 |
| Деталь: | HOOK-T-ARM |
| Парткод: | 6LA09238000 |
| Деталь: | LVR-DF-SEN |
| Парткод: | 6LE04804000 |
| Деталь: | LVR-R-SOL-LS |
| Парткод: | 6LA09184000 |
| Деталь: | LVR-SB-RELS-SOL |
| Парткод: | 6LA09236000 |
| Деталь: | PLT-T-SP |
| Парткод: | 6LA09303000 |
| Деталь: | RINK-SB-RELAS-1 |
| Парткод: | 6LA09228000 |
| Деталь: | RINK-SB-RELAS-2 |
| Парткод: | 6LA09229000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA09399000 |
| Деталь: | SCR-M3X6ITSR-NI |
| Парткод: | 6LA09396000 |
| Деталь: | SPE-DF-SNS |
| Парткод: | 6LA09383000 |
| Деталь: | SPE-R-LSF |
| Парткод: | 6LA09353000 |
| Деталь: | SPE-SB-IDLER |
| Парткод: | 6LA09384000 |
| Деталь: | SPC-SB-RELEASE |
| Парткод: | 6LA09375000 |
| Деталь: | SPC-S-LATCH |
| Парткод: | 6LA09369000 |
| Деталь: | SPL-T-HOK |
| Парткод: | 6LA09385000 |
| Деталь: | SNS-TLP1241 |
| Парткод: | 6LE00883000 |
| Деталь: | SCRW-030060FNWS |
| Парткод: | 6LA09010000 |
| Деталь: | SCRW-3008FNBB |
| Парткод: | 6LA09011000 |
| Деталь: | HPIN20/12SCH |
| Парткод: | 6LA09039000 |
| Деталь: | WH-SIZE-551 |
| Парткод: | 6LA09153000 |
| Деталь: | CVR-OC-OPEN |
| Парткод: | 6LE04815000 |
| Деталь: | SPL-C-GUIDE |
| Парткод: | 6LA09071000 |
| Деталь: | GID-OC-OPEN |
| Парткод: | 6LE04817000 |
| Деталь: | LVR-OC-OR-WZ-SN |
| Парткод: | 6LA09173000 |
| Деталь: | LVR-OC-RSNS |
| Парткод: | 6LA09172000 |
| Деталь: | PLT-OC-RGST |
| Парткод: | 6LA09293000 |
| Деталь: | ROL-OC-1 |
| Парткод: | 6LA09216000 |
| Деталь: | ROL-OC-S |
| Парткод: | 6LA09169000 |
| Деталь: | ROL-OC-2 |
| Парткод: | 6LA09217000 |
| Деталь: | RUB-O-RING |
| Парткод: | 6LA09401000 |
| Деталь: | SFT-OC-CVR-LOCK |
| Парткод: | 6LA09219000 |
| Деталь: | SFT-OC-REJI-N |
| Парткод: | 6LA09467000 |
| Деталь: | CUSH-OC-CLEAN1L |
| Парткод: | 6LA09392000 |
| Деталь: | CUSH-OC-CLEAN1S |
| Парткод: | 6LA09393000 |
| Деталь: | CUSH-OC-CLEAN2 |
| Парткод: | 6LA09391000 |
| Деталь: | SPC-OC-RGST1 |
| Парткод: | 6LA09381000 |
| Деталь: | SPL-OC-RGST2 |
| Парткод: | 6LA09294000 |
| Деталь: | SPE-OC-CVRLOCK |
| Парткод: | 6LA09366000 |
| Деталь: | SPL-OC-EARTH |
| Парткод: | 6LA09376000 |
| Деталь: | SPL-OC-OWSNS |
| Парткод: | 6LA09379000 |
| Деталь: | SPL-OC-RSNS |
| Парткод: | 6LA09380000 |
| Деталь: | MYR-GUI-OC-OP-F |
| Парткод: | 6LA09442000 |
| Деталь: | MYR-GUI-OC-OP-R |
| Парткод: | 6LA09443000 |
| Деталь: | SCRW-4006FNBB |
| Парткод: | 6LA09014000 |
| Деталь: | KI-100 |
| Парткод: | 6LA09020000 |
| Деталь: | SNS-TLP1241 |
| Парткод: | 6LE00883000 |
| Деталь: | SCRW-3008FNBB |
| Парткод: | 6LA09011000 |
| Деталь: | COVER-CONPANE-390-U |
| Парткод: | 6LE07544000 |
| Деталь: | KEY-START |
| Парткод: | 6LE07503000 |
| Деталь: | KEY-STOP |
| Парткод: | 6LE07504000 |
| Деталь: | KEY-FC |
| Парткод: | 6LE07505000 |
| Деталь: | KEY-TEN |
| Парткод: | 6LE07517000 |
| Деталь: | KEY-FUNCTION-A |
| Парткод: | 6LE07518000 |
| Деталь: | KEY-FUNCTION-B |
| Парткод: | 6LE07508000 |
| Деталь: | KEY-FUNCTION-C |
| Парткод: | 6LE07509000 |
| Деталь: | KEY-HELP |
| Парткод: | 6LE07510000 |
| Деталь: | LID-LED-S |
| Парткод: | 6LE07512000 |
| Деталь: | KEY-CONTRAST |
| Парткод: | 6LE07514000 |
| Деталь: | LID-LED-L |
| Парткод: | 6LE07515000 |
| Деталь: | DSP-LCD-390 |
| Парткод: | 6LE07516000 |
| Деталь: | SHIELD-CONPANE |
| Парткод: | 6LE07519000 |
| Деталь: | BRKT-CNP-TNR-SUB |
| Парткод: | 6LE07522000 |
| Деталь: | BRKT-CONPANE |
| Парткод: | 6LE07523000 |
| Деталь: | HRNS-DSP-390 |
| Парткод: | 6LE07526000 |
| Деталь: | HRNS-INV-3 |
| Парткод: | 6LE07527000 |
| Деталь: | HRNS-KEY-20 |
| Парткод: | 6LE07536000 |
| Деталь: | HRNS-KEY-8 |
| Парткод: | 6LE07537000 |
| Деталь: | HRNS-SNSR-THS-L |
| Парткод: | 6LE07525000 |
| Деталь: | HRNS-SNSR-THS-S |
| Парткод: | 6LE07529000 |
| Деталь: | HRNS-VOL-14 |
| Парткод: | 6LE07528000 |
| Деталь: | LID-LED-R |
| Парткод: | 6LE07540000 |
| Деталь: | MYLAR-PWA-KEY |
| Парткод: | 6LE07538000 |
| Деталь: | MYLAR-PWA-VOL |
| Парткод: | 6LE07532000 |
| Деталь: | PNL-TOUCH-390 |
| Парткод: | 6LE07524000 |
| Деталь: | PWA-F-DSP-390 |
| Парткод: | 6LE07534000 |
| Деталь: | PWA-F-INV-390 |
| Парткод: | 6LE07530000 |
| Деталь: | PWA-F-KEY-390 |
| Парткод: | 6LE07535000 |
| Деталь: | PWA-F-VOL-390 |
| Парткод: | 6LE07531000 |
| Деталь: | SHEET-DSP-LCD-390 |
| Парткод: | 6LE07541000 |
| Деталь: | SNSR-THS-390 |
| Парткод: | 6LE09111000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | EDS-1717U |
| Парткод: | F0-00047000 |
| Деталь: | 292254-4 |
| Парткод: | E0-07625000 |
| Деталь: | S/TPP/BID-3X8-NI |
| Парткод: | X0-01989000 |
| Деталь: | S/PAN/SWWP-M3X6-NI |
| Парткод: | X0-00060000 |
| Деталь: | ASY-S-SOL-SUB |
| Парткод: | 6LA09113000 |
| Деталь: | BLT-152-S2M-4 |
| Парткод: | 6LA09044000 |
| Деталь: | BLT-160-S2M-4 |
| Парткод: | 6LA09046000 |
| Деталь: | BRKT-FEED-MOT |
| Парткод: | 6LA15836000 |
| Деталь: | BRKT-FEED-M-TEN |
| Парткод: | 6LA15835000 |
| Деталь: | BRKT-S-SMOT |
| Парткод: | 6LA09298000 |
| Деталь: | BRKT-S-SMOT-TEN |
| Парткод: | 6LA09299000 |
| Деталь: | BRKT-S-SOL |
| Парткод: | 6LA09278000 |
| Деталь: | BUSH6 |
| Парткод: | 6LA09062000 |
| Деталь: | CLIP4 |
| Парткод: | 6LA09074000 |
| Деталь: | CLIP5 |
| Парткод: | 6LA09057000 |
| Деталь: | LVR-S-SOL |
| Парткод: | 6LA09202000 |
| Деталь: | M/DC-S-ORG-EXIT |
| Парткод: | 6LA09144000 |
| Деталь: | MOTR.S-L-EXIT-608 |
| Парткод: | 6LE04821000 |
| Деталь: | PLY/T-S2M-17 |
| Парткод: | 6LA09206000 |
| Деталь: | PLY/T-S2M-17-OW |
| Парткод: | 6LA09207000 |
| Деталь: | SCR-M3X6ITSR-NI |
| Парткод: | 6LA09396000 |
| Деталь: | SPE-FEED-MOT |
| Парткод: | 6LA09360000 |
| Деталь: | SPE-S-SMOT |
| Парткод: | 6LA09361000 |
| Деталь: | SCRW-4006FNIT |
| Парткод: | 6LA09015000 |
| Деталь: | SCRW-030060FNWS |
| Парткод: | 6LA09010000 |
| Деталь: | BUSH-06 |
| Парткод: | 6LA09017000 |
| Деталь: | ASYS-GEAR-10H024-IDR |
| Парткод: | 6LE04537000 |
| Деталь: | WALL-MIXER-300 |
| Парткод: | 4406332690 |
| Деталь: | PADDLE-DEV-300 |
| Парткод: | 4406332460 |
| Деталь: | ASYS-BUSH-PDL-F |
| Парткод: | 6LA02416000 |
| Деталь: | ASY-COV-DEV-390 |
| Парткод: | 6LE04525000 |
| Деталь: | MIXER-1-340 |
| Парткод: | 6LA02410000 |
| Деталь: | K-MIXER-2-340 |
| Парткод: | 6LA02412000 |
| Деталь: | 626DDM3MTLY13 |
| Парткод: | F0-01204000 |
| Деталь: | GEAR-08S045-06 |
| Парткод: | 4406332590 |
| Деталь: | K-NOZZLE-MIXER |
| Парткод: | 6LA02430000 |
| Деталь: | COV-NOZLE-MIX |
| Парткод: | 6LA02436000 |
| Деталь: | BUSH-6X12X4R8F |
| Парткод: | 6LA65696000 |
| Деталь: | ROLLER-MGN-TR |
| Парткод: | 4406332450 |
| Деталь: | L-1680DDRPOP25LY13 |
| Парткод: | F0-01206000 |
| Деталь: | ROLLER-MGN-U340 |
| Парткод: | 6LA02380000 |
| Деталь: | SHIELD-MG-U-F-6 |
| Парткод: | 6LA02398000 |
| Деталь: | K-SHIELD-MG-U-R |
| Парткод: | 4406332770 |
| Деталь: | ROLLER-MGN-L340 |
| Парткод: | 6LA02381000 |
| Деталь: | SHIELD-MG-L-F-6 |
| Парткод: | 6LA02399000 |
| Деталь: | K-SHIELD-MG-L-R |
| Парткод: | 4406332800 |
| Деталь: | SCRAPER-MG-L |
| Парткод: | 4406332820 |
| Деталь: | SEAL-MG-SIDE2 |
| Парткод: | 4406333280 |
| Деталь: | K-HLDR-MG-F340 |
| Парткод: | 6LA02386000 |
| Деталь: | HLDR-MG-HI-L-6 |
| Парткод: | 6LA02384000 |
| Деталь: | HLDR-MG-HI-U-6 |
| Парткод: | 6LA02385000 |
| Деталь: | GEAR-10H017-MG |
| Парткод: | 4406332650 |
| Деталь: | GEAR-10H025-390 |
| Парткод: | 6LE04512000 |
| Деталь: | SPA-PSH-MG-100 |
| Парткод: | 6LA08940000 |
| Деталь: | GEAR-10H015_08S16-390 |
| Парткод: | 6LE04510000 |
| Деталь: | GEAR-10H023-TR |
| Парткод: | 4406332550 |
| Деталь: | SEAL-VC6-10-2.5 |
| Парткод: | 4401949290 |
| Деталь: | SEAL-VC8-12-2.5 |
| Парткод: | 4406333150 |
| Деталь: | S/HEX-M38-NI |
| Парткод: | 6LA08901000 |
| Деталь: | RR/E-3-SS |
| Парткод: | X0-00964000 |
| Деталь: | RR/E-4-SS |
| Парткод: | X0-00965000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | RR/E-7-SS |
| Парткод: | X0-00968000 |
| Деталь: | S/BID-M3X4-BSNI |
| Парткод: | X0-01724000 |
| Деталь: | S/PAN-M3X6-NI |
| Парткод: | X0-00057000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | GEAR-10H19_08S45-390 |
| Парткод: | 6LE04513000 |
| Деталь: | GG10H024/08S045 |
| Парткод: | 4406332600 |
| Деталь: | BUSH-MGHI-TR-R-390 |
| Парткод: | 6LE04505000 |
| Деталь: | BUSH-MGHI-TR-R |
| Парткод: | 4406332740 |
| Деталь: | ASYS-HLDR-MG-R-390 |
| Парткод: | 6LE04503000 |
| Деталь: | K-HLDR-MG-R |
| Парткод: | 4406332530 |
| Деталь: | WH-TRSP-SNS-551 |
| Парткод: | 6LA09157000 |
| Деталь: | ASY-CVR-R--PLT |
| Парткод: | 6LA09135000 |
| Деталь: | ASYS-OC-FULCR |
| Парткод: | 6LA09121000 |
| Деталь: | ASYS-BKT-HING-F |
| Парткод: | 6LA09080000 |
| Деталь: | ASYS-BKT-HING-R |
| Парткод: | 6LA09131000 |
| Деталь: | BRSH-S-EXIT |
| Парткод: | 6LA09354000 |
| Деталь: | CVR-F |
| Парткод: | 6LE04813000 |
| Деталь: | CVR-R |
| Парткод: | 6LE04814000 |
| Деталь: | CVR-R-PLT |
| Парткод: | 6LA09246000 |
| Деталь: | CVR-R-PLT1 |
| Парткод: | 6LA09250000 |
| Деталь: | CVR-R-PLT2 |
| Парткод: | 6LA09251000 |
| Деталь: | CVR-R-SUB |
| Парткод: | 6LE04805000 |
| Деталь: | GUID-R-LS |
| Парткод: | 6LA09174000 |
| Деталь: | GID-S-U |
| Парткод: | 6LE04818000 |
| Деталь: | HLDR-S-TRY-SUB |
| Парткод: | 6LA09249000 |
| Деталь: | LVR-TRSP-SNS |
| Парткод: | 6LA09170000 |
| Деталь: | SCRW-M3-3.2 |
| Парткод: | 6LA09434000 |
| Деталь: | MGT-TRY-L93 |
| Парткод: | 6LE04830000 |
| Деталь: | PLT-R-LS-BASE |
| Парткод: | 6LA09264000 |
| Деталь: | ROL-S-EXIT |
| Парткод: | 6LA09211000 |
| Деталь: | RUB-O-RING |
| Парткод: | 6LA09401000 |
| Деталь: | SCR-DAN-3X8 |
| Парткод: | 6LA09372000 |
| Деталь: | SCR-M3X6ITSR-NI |
| Парткод: | 6LA09396000 |
| Деталь: | SCR-M3X6BISR-NI |
| Парткод: | 6LA09399000 |
| Деталь: | SFT-S-EXIT-ROL |
| Парткод: | 6LA09326000 |
| Деталь: | SHEET-H48-1-S |
| Парткод: | 6LA09367000 |
| Деталь: | SPL-R-LS |
| Парткод: | 6LA09265000 |
| Деталь: | SPL-S-CSNS |
| Парткод: | 6LA09378000 |
| Деталь: | SPL-S-EXIT-ROL |
| Парткод: | 6LA09287000 |
| Деталь: | SPL-S-LTRY-EART |
| Парткод: | 6LA09374000 |
| Деталь: | TRAY-S-L93 |
| Парткод: | 6LA15903000 |
| Деталь: | TRY-S-S |
| Парткод: | 6LE04812000 |
| Деталь: | TRY-S-S-SUB |
| Парткод: | 6LA09247000 |
| Деталь: | ROLL-16R |
| Парткод: | 6LA09069000 |
| Деталь: | MLR-HNG-CVR |
| Парткод: | 6LA14881000 |
| Деталь: | PIN-3-31.6 |
| Парткод: | 6LA09064000 |
| Деталь: | CUSH-L-TRY |
| Парткод: | 6LA09339000 |
| Деталь: | SCRW-3010FNBB |
| Парткод: | 6LA09013000 |
| Деталь: | KI-100 |
| Парткод: | 6LA09020000 |
| Деталь: | SNS-TLP1241 |
| Парткод: | 6LE00883000 |
| Деталь: | SCRW-3008FNBB |
| Парткод: | 6LA09011000 |
| Деталь: | CARRIGE-1-390 |
| Парткод: | 6LE08100000 |
| Деталь: | FOOT-CRG-3.64 |
| Парткод: | 4408604590 |
| Деталь: | LAMP-EXPO-390 |
| Парткод: | 6LE09308000 |
| Деталь: | INV-EXPO-390 |
| Парткод: | 6LE09311000 |
| Деталь: | REFLECTOR-LAMP |
| Парткод: | 6LA01810000 |
| Деталь: | HRNS-INV-390 |
| Парткод: | 6LE09212000 |
| Деталь: | GUIDE-WH-CRG1 |
| Парткод: | 6LA01817000 |
| Деталь: | ES-0505-2 |
| Парткод: | F0-00120000 |
| Деталь: | S/PAN/SWWP-M3X8-NI |
| Парткод: | X0-00077000 |
| Деталь: | S/BID-M3X6-NI |
| Парткод: | X0-00430000 |
| Деталь: | CASSETTE-390B |
| Парткод: | 6LA15843100 |
| Деталь: | ASYS-SHAFT-TRAY-UP |
| Парткод: | 6LE03700000 |
| Деталь: | LEVER-SENS |
| Парткод: | 6LA04446000 |
| Деталь: | LVR-ELV-CST |
| Парткод: | 6LA14516000 |
| Деталь: | CUSHION-CST |
| Парткод: | 4400908680 |
| Деталь: | SIDE-WALL-F-390B |
| Парткод: | 6LA15842100 |
| Деталь: | PLT-LVR-CST-340 |
| Парткод: | 6LA15847000 |
| Деталь: | LVR-LOCK-CST |
| Парткод: | 6LE03710000 |
| Деталь: | PLT-LOCK-CST-340 |
| Парткод: | 6LA15844000 |
| Деталь: | SPC-LVR-WALL-F |
| Парткод: | 6LA56695000 |
| Деталь: | SIDE-WALL-R-390B |
| Парткод: | 6LA15841100 |
| Деталь: | LEVER-LOCK-WALL-RER |
| Парткод: | 6LA29058000 |
| Деталь: | WALL-LOCK-R-340 |
| Парткод: | 6LA04433000 |
| Деталь: | SPL-LOCK-WALL-R |
| Парткод: | 41305546000 |
| Деталь: | SHAFT-GUIDE |
| Парткод: | 6LE03702000 |
| Деталь: | BRKT-SHAFT |
| Парткод: | 6LA04463000 |
| Деталь: | GER-PINION-20-AT |
| Парткод: | 41306029000 |
| Деталь: | SCREW-PINION |
| Парткод: | 6LA04456000 |
| Деталь: | TRAY-390 |
| Парткод: | 6LE03714000 |
| Деталь: | PAD-CST-340 |
| Парткод: | 6LA04500000 |
| Деталь: | WALL-CSSTT-END |
| Парткод: | 6LA29061000 |
| Деталь: | COVER-CSSTT-LWR |
| Парткод: | 6LE04404000 |
| Деталь: | COVER-CSSTT-UPR |
| Парткод: | 6LE04403000 |
| Деталь: | BRKT-CST-POS-390 |
| Парткод: | 6LE03713000 |
| Деталь: | STUD-CST-POS |
| Парткод: | 6LA04487000 |
| Деталь: | BRKT-FIX-PINION |
| Парткод: | 6LA14327000 |
| Деталь: | CAP-LEVER-SENS |
| Парткод: | 6LA14466000 |
| Деталь: | WALL-END-TAB390 |
| Парткод: | 6LE03705000 |
| Деталь: | S/TPP/BID-3X8-NI |
| Парткод: | X0-01989000 |
| Деталь: | S/HEX-M48-NI |
| Парткод: | 6LA08905000 |
| Деталь: | S/HEX-M36-NI |
| Парткод: | 6LA08900000 |
| Деталь: | S/TPP/HEX-48-NI |
| Парткод: | 6LA08921000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
| Деталь: | W/TH/A-4-SS |
| Парткод: | X0-01889000 |
| Деталь: | SIZE-CST-390-UC |
| Парткод: | 6LE03708000 |
| Деталь: | SIZE-CST-390-E |
| Парткод: | 6LE03709000 |
| Деталь: | LBL-O-CST-390 |
| Парткод: | 6LE03707000 |
| Деталь: | LBL-O-CST-390 |
| Парткод: | 6LE03711000 |
| Деталь: | LBL-CST-LCD-SUB |
| Парткод: | 6LE03712000 |
| Деталь: | HLDR-R-CLN |
| Парткод: | 6LA02742000 |
| Деталь: | LEVER-CLAW-F340 |
| Парткод: | 6LA02716000 |
| Деталь: | SPE-CLAW-ON-OFF |
| Парткод: | 6LA08944000 |
| Деталь: | LEVER-BLADE-300 |
| Парткод: | 4406328890 |
| Деталь: | CAM-BLADE |
| Парткод: | 4401904770 |
| Деталь: | HRNS-CLN-UNIT-390 |
| Парткод: | 6LE09405000 |
| Деталь: | ESC-0912 |
| Парткод: | F0-01248000 |
| Деталь: | SKB-1 |
| Парткод: | F0-00521000 |
| Деталь: | LWS-05 |
| Парткод: | F0-00035000 |
| Деталь: | BRKT-THMS-DRM |
| Парткод: | 4406329110 |
| Деталь: | THMS-DRM-390 |
| Парткод: | 6LE09110000 |
| Деталь: | ASYS-GUIGE-T-SENS |
| Парткод: | 6LE04105000 |
| Деталь: | WHEEL-CLN-320 |
| Парткод: | 44203459000 |
| Деталь: | SNSR-MTD-390 |
| Парткод: | 6LE09115000 |
| Деталь: | SEAL-FRM-CLN-F |
| Парткод: | 6LA02747000 |
| Деталь: | SEAL-FRM-CLN-R |
| Парткод: | 6LA02748000 |
| Деталь: | SCREW-ARM-CLN |
| Парткод: | 4400805530 |
| Деталь: | HSG-DRUM-F |
| Парткод: | 6LA02728000 |
| Деталь: | SHEET-GUIDE-CLN |
| Парткод: | 6LA02647000 |
| Деталь: | S/HEX-M36-NI |
| Парткод: | 6LA08900000 |
| Деталь: | S/PAN-M3X6-NI |
| Парткод: | X0-00057000 |
| Деталь: | S/HEX-M38-NI |
| Парткод: | 6LA08901000 |
| Деталь: | S/TPP/HEX-410-NI |
| Парткод: | 6LA08922000 |
| Деталь: | S/HEX-M48-NI |
| Парткод: | 6LA08905000 |
| Деталь: | RR/E-5-SS |
| Парткод: | X0-00966000 |
| Деталь: | S/PAN-M3X4-NI |
| Парткод: | X0-02113000 |
| Деталь: | S/TPP/HEX-38-NI |
| Парткод: | 6LA08917000 |
Коды ошибок
C130
C140
C150
C160
C180
C1A0
C1C0
C260
C270
C280
C360
C370
C411
C412
C443
C445
C446
C447
C449
C465
C466
C467
C468
C471
C472
C473
C474
C475
C480
C481
C490
C4A0
C4B0
C550
C560
C570
C580
C590
C730
C820
C830
C840
C850
C860
C870
C940
C970
CA10
CA20
CA30
CA41
CA42
CA43
CA44
CA50
CA90
CAA0
CAB0
CAC0
CAF0
CB10
CB20
CB30
CB40
CB50
CB60
CB70
CB80
CB90
CBA0
CBB0
CBC0
CBD0
CBE0
CBF0
CC00
CC10
CC20
CC40
CC50
CC60
CCC1
CCD1
CCE1
CD00
CD10
CD20
CD30
CD40
CD50
CE50
CE90
CF70
CF80
E010
E020
E030
E061
E062
E063
E064
E065
E090
E110
E120
E130
E140
E150
E160
E180
E190
E200
E201
E210
E211
E220
E230
E240
E250
E260
E261
E2A1
E300
E301
E310
E320
E330
E331
E340
E350
E360
E370
E380
E3C0
E3C1
E3D0
E3E0
E3F0
E410
E440
E450
E460
E470
E510
E511
E512
E540
E550
E570
E580
E590
E5A0
E711
E712
E713
E714
E715
E716
E721
E722
E723
E724
E725
E726
E728
E731
E732
E733
E741
E742
E743
E751
E752
E761
E762
E763
E764
E765
E766
E767
E768
E800
E860
E870
E9F0
EA10
EA20
EA30
EA40
EA50
EA60
EA80
EA90
EAA0
EAB0
EAC0
EAD0
EAE0
EB30
EB50
EB60
EC00
EC10
EC20
EC30
EC40
EC50
EC60
EC70
EC80
EC90
ECA0
ECB0
ECC0
ECD0
F070
F090
F091
F092
F100
F101
F102
F103
F104
F105
F106
F107
F108
F110
F111
F120
F130
Описание
| Error code: | C130 |
| Description: | 1st drawer tray abnormality: The tray-up motor-1 does not run normally or the 1st drawer tray does not move normally. (Feeding of any other drawer than the 1st drawer is possible.) |
| Causes: | Tray-up motor Tray-up sensor PFC board |
| Remedy: | Does the tray go up? (Perform the output check in the test mode: 03-276,278,279,280) ↓ → NO → 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector CN331 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[E], /[2]/[E], /[3]/[E] ,/[4]/[E]) ↓ → NO → 1. Check if the connector of the sensor is disconnected. 2. Check if the connector CN329, CN328, CN350 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. YES 1. Check if the positioning pin of the drawer is tightly screwed. 2. Check if the paper is not caught in the coupling when the tray goes up. 3. Check if the conductor pattern on the LGC board is short circuited or open circuited. 4. Replace the LGC board. |
| Error code: | C140 |
| Description: | 2nd drawer tray abnormality: The tray-up motor-1 does not run normally or the 2nd drawer tray does not move normally. (Feeding of any other drawer than the 2nd drawer is possible.) |
| Causes: | Tray-up motor Tray-up sensor PFC board |
| Remedy: | Does the tray go up? (Perform the output check in the test mode: 03-276,278,279,280) ↓ → NO → 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector CN331 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[E], /[2]/[E], /[3]/[E] ,/[4]/[E]) ↓ → NO → 1. Check if the connector of the sensor is disconnected. 2. Check if the connector CN329, CN328, CN350 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. YES 1. Check if the positioning pin of the drawer is tightly screwed. 2. Check if the paper is not caught in the coupling when the tray goes up. 3. Check if the conductor pattern on the LGC board is short circuited or open circuited. 4. Replace the LGC board. |
| Error code: | C150 |
| Description: | 3rd drawer tray abnormality: The tray-up motor-2 does not run normally or the 3rd drawer tray does not move normally. (Feeding of any other drawer than the 3rd drawer is possible.) |
| Causes: | Tray-up motor Tray-up sensor PFC board |
| Remedy: | Does the tray go up? (Perform the output check in the test mode: 03-276,278,279,280) ↓ → NO → 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector CN331 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[E], /[2]/[E], /[3]/[E] ,/[4]/[E]) ↓ → NO → 1. Check if the connector of the sensor is disconnected. 2. Check if the connector CN329, CN328, CN350 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. YES 1. Check if the positioning pin of the drawer is tightly screwed. 2. Check if the paper is not caught in the coupling when the tray goes up. 3. Check if the conductor pattern on the LGC board is short circuited or open circuited. 4. Replace the LGC board. |
| Error code: | C160 |
| Description: | 4th drawer tray abnormality: The tray-up motor-2 does not run normally or the 4th drawer tray does not move normally. (Feeding of any other drawer than the 4th drawer is possible.) |
| Causes: | Tray-up motor Tray-up sensor PFC board |
| Remedy: | Does the tray go up? (Perform the output check in the test mode: 03-276,278,279,280) ↓ → NO → 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector CN331 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[E], /[2]/[E], /[3]/[E] ,/[4]/[E]) ↓ → NO → 1. Check if the connector of the sensor is disconnected. 2. Check if the connector CN329, CN328, CN350 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. YES 1. Check if the positioning pin of the drawer is tightly screwed. 2. Check if the paper is not caught in the coupling when the tray goes up. 3. Check if the conductor pattern on the LGC board is short circuited or open circuited. 4. Replace the LGC board. |
| Error code: | C180 |
| Description: | Tandem LCF tray-up motor abnormality: The Tandem LCF tray-up motor does not run normally or the Tandem LCF tray does not move normally. (Feeding of any other drawer than the Tandem LCF is possible.) |
| Causes: | LCF tray-up motor LCF tray-up sensor LCF tray bottom sensor PFC board |
| Remedy: | Does the tray move? (Perform the output check in the test mode: 03-270) ↓ → NO → 1. Check if the connector of the Tandem LCF tray-up motor is disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 5. Replace the LCF tray-up moter. 6. Replace the LGC board. YES Are the 3rd drawer/tandem LCF tray-up sensor and tandem LCF bottom sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[3]/[E], /[8]/[F]) ↓ → NO → 1. Check if the connectors of the sensors are disconnected. 2. Check if the connector CN328, CN345 on the LGC board is disconnected. 3. Check if the slit reaches the sensors. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 6. Replace the LGC board. YES 1. Check if the driving mechanism is abnormal. 2. Check if the conductor pattern on the LGC board is short circuited or open circuited. 3. Replace the LGC board. |
| Error code: | C1A0 |
| Description: | Tandem LCF end fence motor abnormality: The Tandem LCF end fence motor does not run normally or the Tandem LCF end fence does not move normally. (Feeding of any other drawer than the Tandem LCF is possible.) |
| Causes: | LCF end fence motor LCF end fence home position sensor LCF end fence stop position sensor PFC board |
| Remedy: | Is the Tandem LCF end fence motor working? (Perform the output check in the test mode: 03-207) ↓ → NO → 1. Check if the connector of the Tandem LCF end fence motor is disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 5. Replace the Tanden LCF end fence motor. 6. Replace the LGC board. YES Are the LCF end fence stop position sensors working? (Perform the input check in the test mode: 03-[FAX]OFF/[8]/[G], /[8]/[H]) ↓ → NO → 1. Check if the connectors of the sensors are disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the slit reaches the sensors. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 6. Replace the LGC board. YES 1. Check if the driving mechanism is abnormal. 2. Check if the conductor pattern on the LGC board is short circuited or open circuited. 3. Replace the LGC board. |
| Error code: | C1C0 |
| Description: | Option LCF tray-up motor abnormality: The Option LCF tray-up motor does not run normally or the Option LCF tray does not move normally. (Feeding of any other drawer than the Option LCF is possible.) |
| Causes: | Option LCF bottom sensor Option LCF top sensor LCF board PFC board |
| Remedy: | Is the tray motor driving? (Perform the output check in the test mode: 03-271) ↓ → NO → 1. Check if the connector on the LCF tray motor is not disconnected. 2. Check if the connectors J851 on the LCF board are not disconnected. 3. Check if the connector of the tray-up sensor is not disconnected. 4. Check if the actuator reaches the sensor. 5. Replace the LCF board. 6. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX] OFF/[5]/[E] ↓ → NO → 1. Check if the connector of the tray-up sensor is not disconnected. 2. Check if the connectors J851 on the LCF board are not disconnected. 3. Check if the actuator reaches the sensor. 4. Check if the connector pins are not disconnected and the harness is not open circuited. 5. Replace the LCF board. 6. Replace the LGC board. YES 1. Check if the tray lifting mechanism has no abnormality. 2. Replace the LCF board. 3. Replace the LGC board. |
| Error code: | C260 |
| Description: | Peak detection error: Lighting of the exposure lamp (white reference) is not detected when the power is turned ON. |
| Causes: | Lens unit SLG board Exposure lamp Supply harness |
| Remedy: | Does the exposure lamp light? (Perform the output check in the test mode: 03-267) ↓ → YES → 1. Check if the connectors on the CCD and SLG boards are disconnected. 2. Check if the shading correction plate is detached or dirty. 3. Check if the conductor pattern on the CCD board is short circuited or open circuited. 4. Check if the conductor pattern on the SLG board is short circuited or open circuited. 5. Replace the lens unit. 6. Replace the SLG board. NO 1. Check if the connectors of the exposure lamp and inverter are disconnected. 2. Check the SLG board if the connector pin CN1 is disconnected and the harness is short circuited or open circuited. 3. Check if the conductor pattern on the SLG board is short circuited or open circuited. 4. Replace the SLG board. 5. Replace the inverter. 6. Replace the exposure lamp. |
| Error code: | C270 |
| Description: | Carriage home position sensor not turning OFF within a specified period of time: The carriages do not shift from their home position within a specified period of time. |
| Causes: | Carriage home position sensor Carriage home position sensor harness SLG board Scan motor Scan motor harness |
| Remedy: | Remove the original glass and move the carriages to the paper feeding side. Turn ON the power and check the following items. Are the carriages slightly moved to the feeding direction? Are the carriages staying at a position other than home position? ll → YES → 1. Check if the conductor pattern on the SLG board is short circuited or open circuited. 2. Replace the SLG board. NO 1. Check if the connector pin is disconnected and the harness is short circuited or open circuited. 2. Check if the conductor pattern on the SLG board is short circuited or open circuited. 3. Replace the SLG board. |
| Error code: | C280 |
| Description: | Carriage home position sensor not turning ON within a specified period of time: The carriages do not reach their home position within a specified period of time. |
| Causes: | Carriage home position sensor Carriage home position sensor harness SLG board Scan motor Scan motor harness |
| Remedy: | Do the carriages make a big noise after they arrive at the home position? ↓ → YES → The carriage home position sensor is not turned ON. 1. Check if the connector of the sensor is disconnected. 2. Replace the carriage home position sensor. 3. Check if the conductor pattern on the SLG board is short circuited or open circuited. 4. Replace the SLG board. NO The carriages are stopped at the home position and do not move. 1. Check if the connector pins are disconnected and the harnesses are short circuited or open circuited. 2. Check if the conductor pattern on the SLG board is short circuited or open circuited. 3. Replace the SLG board. |
| Error code: | C360 |
| Description: | Wire cleaner drive motor abnormality: The wire cleaner drive motor does not run normally or the charger wire cleaner does not move normally. |
| Causes: | Needle electrode cleaner detection sensor Needle electrode cleaner drive motor EPU board LGC board |
| Remedy: | (1) Check if the main charger is not disconnected. (2) Check if the wire cleaner drive motor is driving. (3) Is the wire cleaner position detection switch working? (4) Replace the LGC board. |
| Error code: | C370 |
| Description: | Transfer belt cam motor abnormality: The transfer belt cam motor does not run normally when the power is turned ON or the copying is started. |
| Causes: | Transfer belt contact/release detection sensor Transfer belt motor DRV board LGC board |
| Remedy: | (1) Is the transport belt unit working normally? (there is no extraneous material or toner clod). (2) Check if the connector of the transfer belt cam motor is not disconnected. (3) Check if the connector CN335 on the LGC board is disconnected. (4) Check if the fuse on the LVPS has blown. (5) Check if the transfer belt release detection sensor and transfer belt contact detection sensor is working properly. (6) Replace the transfer belt cam motor. (7) Replace the LGC board. |
| Error code: | C411 |
| Description: | Thermistor/heater abnormality at power-ON: Thermistor abnormality is detected at power-ON or the fuser roller temperature does not rise within a specified period of time after power-ON. |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1.Check the power voltage (1) Check if the power voltage is normal.(Is the voltage during the operation ±10% of the rated voltage?) 2.Check the thermistors (1) Check if the connectors are disconnected. (2) Check if the center and side thermistors (front, rear) are in contact with the surface of the fuser roller properly? (3) Check if the harnesses of the center and side thermistors (front, rear) are open circuited. 3. Check the heater (1) Check if the IH coil is broken. (2) Check if the connector of the IH coil is disconnected. (3) Check if the thermostat is blown. (4) Check if the connectors on the IH control board are disconnected (AC input connector and LGC I/F connectors CN455). (5) Check if the IH control board is abnormal. • Replace the IH control board. 4. Check the LGC board (1) Check if the connectors CN332,CN334 are disconnected. (2) Check if the conductor pattern on the LGC board is short circuited or open circuited. (3) Replace the LGC board. 5. Clear the status counter After repairing the matter which caused the error [C411/C412], perform the following: (1) Turn ON the power while [0] and [8] are pressed simultaneously. (2) Key in "400", then press [START]. (3) Change the current status counter value "1" or "2" to "0", then press [ENTER] or [INTERRUPT] (to cancel [C411/C412]). (4) Turn the power OFF and then back ON. Make sure that the equipment enters the normal ready state. |
| Error code: | C412 |
| Description: | Thermistor/heater abnormality at power-ON: Thermistor abnormality is detected at power-ON or the fuser roller temperature does not rise within a specified period of time after power-ON. |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1.Check the power voltage (1) Check if the power voltage is normal.(Is the voltage during the operation ±10% of the rated voltage?) 2.Check the thermistors (1) Check if the connectors are disconnected. (2) Check if the center and side thermistors (front, rear) are in contact with the surface of the fuser roller properly? (3) Check if the harnesses of the center and side thermistors (front, rear) are open circuited. 3. Check the heater (1) Check if the IH coil is broken. (2) Check if the connector of the IH coil is disconnected. (3) Check if the thermostat is blown. (4) Check if the connectors on the IH control board are disconnected (AC input connector and LGC I/F connectors CN455). (5) Check if the IH control board is abnormal. • Replace the IH control board. 4. Check the LGC board (1) Check if the connectors CN332,CN334 are disconnected. (2) Check if the conductor pattern on the LGC board is short circuited or open circuited. (3) Replace the LGC board. 5. Clear the status counter After repairing the matter which caused the error [C411/C412], perform the following: (1) Turn ON the power while [0] and [8] are pressed simultaneously. (2) Key in "400", then press [START]. (3) Change the current status counter value "1" or "2" to "0", then press [ENTER] or [INTERRUPT] (to cancel [C411/C412]). (4) Turn the power OFF and then back ON. Make sure that the equipment enters the normal ready state. |
| Error code: | C443 |
| Description: | Heater abnormality after abnormality judgment (not reaching to intermediate temperature) |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1,2.3. Check the thermistors, Heater and LGC board Check the above components following the procedures 1, 2 and 3 for [C411/C412]. 4. Clear the status counter Change the current status counter value (08-400) "3", "5" , "6" , "9" , "19" , "21" , "22" , "23" , "24" , "25" , "27" or "29" to "0" for [C44X], taking the same procedure as that for [C41X]. • The status counter value is as follows in the following cases. - The error occurred during warming-up: "3", "5" or "6" - The error occurred after the equipment has become ready: "7" - The temperature detected by the center thermistor is 240°C or higher, the temperature detected by the side thermistor is 250°C or higher or the temperature detected by the edge thermistor is 270°C or higher: "9", "19", "21", "22", "23", "25", "27" or "29". - The error occurred during printing: "24" or "25" - The error occurred during energy saving: "26" or "27" - A paper jam occurred: "28" or "29" |
| Error code: | C445 |
| Description: | Heater abnormality after abnormality judgment (prerunning end temperature abnormality) |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1,2.3. Check the thermistors, Heater and LGC board Check the above components following the procedures 1, 2 and 3 for [C411/C412]. 4. Clear the status counter Change the current status counter value (08-400) "3", "5" , "6" , "9" , "19" , "21" , "22" , "23" , "24" , "25" , "27" or "29" to "0" for [C44X], taking the same procedure as that for [C41X]. • The status counter value is as follows in the following cases. - The error occurred during warming-up: "3", "5" or "6" - The error occurred after the equipment has become ready: "7" - The temperature detected by the center thermistor is 240°C or higher, the temperature detected by the side thermistor is 250°C or higher or the temperature detected by the edge thermistor is 270°C or higher: "9", "19", "21", "22", "23", "25", "27" or "29". - The error occurred during printing: "24" or "25" - The error occurred during energy saving: "26" or "27" - A paper jam occurred: "28" or "29" |
| Error code: | C446 |
| Description: | Heater abnormality after abnormality judgment (prerunning end temperature abnormality) |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1,2.3. Check the thermistors, Heater and LGC board Check the above components following the procedures 1, 2 and 3 for [C411/C412]. 4. Clear the status counter Change the current status counter value (08-400) "3", "5" , "6" , "9" , "19" , "21" , "22" , "23" , "24" , "25" , "27" or "29" to "0" for [C44X], taking the same procedure as that for [C41X]. • The status counter value is as follows in the following cases. - The error occurred during warming-up: "3", "5" or "6" - The error occurred after the equipment has become ready: "7" - The temperature detected by the center thermistor is 240°C or higher, the temperature detected by the side thermistor is 250°C or higher or the temperature detected by the edge thermistor is 270°C or higher: "9", "19", "21", "22", "23", "25", "27" or "29". - The error occurred during printing: "24" or "25" - The error occurred during energy saving: "26" or "27" - A paper jam occurred: "28" or "29" |
| Error code: | C447 |
| Description: | Heater abnormality after abnormality judgment (temperature abnormality at ready status) |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1,2.3. Check the thermistors, Heater and LGC board Check the above components following the procedures 1, 2 and 3 for [C411/C412]. 4. Clear the status counter Change the current status counter value (08-400) "3", "5" , "6" , "9" , "19" , "21" , "22" , "23" , "24" , "25" , "27" or "29" to "0" for [C44X], taking the same procedure as that for [C41X]. • The status counter value is as follows in the following cases. - The error occurred during warming-up: "3", "5" or "6" - The error occurred after the equipment has become ready: "7" - The temperature detected by the center thermistor is 240°C or higher, the temperature detected by the side thermistor is 250°C or higher or the temperature detected by the edge thermistor is 270°C or higher: "9", "19", "21", "22", "23", "25", "27" or "29". - The error occurred during printing: "24" or "25" - The error occurred during energy saving: "26" or "27" - A paper jam occurred: "28" or "29" |
| Error code: | C449 |
| Description: | Heater abnormality after abnormality judgment (overheating) |
| Causes: | Thermopiles Fuser unit IH coil IH board LGC board |
| Remedy: | 1,2.3. Check the thermistors, Heater and LGC board Check the above components following the procedures 1, 2 and 3 for [C411/C412]. 4. Clear the status counter Change the current status counter value (08-400) "3", "5" , "6" , "9" , "19" , "21" , "22" , "23" , "24" , "25" , "27" or "29" to "0" for [C44X], taking the same procedure as that for [C41X]. • The status counter value is as follows in the following cases. - The error occurred during warming-up: "3", "5" or "6" - The error occurred after the equipment has become ready: "7" - The temperature detected by the center thermistor is 240°C or higher, the temperature detected by the side thermistor is 250°C or higher or the temperature detected by the edge thermistor is 270°C or higher: "9", "19", "21", "22", "23", "25", "27" or "29". - The error occurred during printing: "24" or "25" - The error occurred during energy saving: "26" or "27" - A paper jam occurred: "28" or "29" |
| Error code: | C465 |
| Description: | Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality) |
| Causes: | Power supply unit LGC board |
| Remedy: | 1. Check the pressure roller thermistor (1) Check if the connector is disconnected. (2) Check if the pressure roller thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the pressure roller thermistor is open circuited. 2. Check the LGC board (1) Check if the connector CN332,CN334 is disconnected. (2) Check if the conductor pattern on the board is short circuited or open circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) "5", "6" , "7" , "8" , "18" , "20" , "24" , "26" or "28" to "0" |
| Error code: | C466 |
| Description: | Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality) |
| Causes: | Power supply unit LGC board |
| Remedy: | 1. Check the pressure roller thermistor (1) Check if the connector is disconnected. (2) Check if the pressure roller thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the pressure roller thermistor is open circuited. 2. Check the LGC board (1) Check if the connector CN332,CN334 is disconnected. (2) Check if the conductor pattern on the board is short circuited or open circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) "5", "6" , "7" , "8" , "18" , "20" , "24" , "26" or "28" to "0" |
| Error code: | C467 |
| Description: | Pressure roller thermistor abnormality after entering ready status (temperature abnormality at ready status) |
| Causes: | Pressure roller thermistor Fuser unit Power supply LGC board |
| Remedy: | 1. Check the pressure roller thermistor (1) Check if the connector is disconnected. (2) Check if the pressure roller thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the pressure roller thermistor is open circuited. 2. Check the LGC board (1) Check if the connector CN332,CN334 is disconnected. (2) Check if the conductor pattern on the board is short circuited or open circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) "5", "6" , "7" , "8" , "18" , "20" , "24" , "26" or "28" to "0" |
| Error code: | C468 |
| Description: | Pressure roller thermistor abnormality after entering ready status (overheating) |
| Causes: | Pressure roller thermistor Fuser unit Power supply LGC board |
| Remedy: | 1. Check the pressure roller thermistor (1) Check if the connector is disconnected. (2) Check if the pressure roller thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the pressure roller thermistor is open circuited. 2. Check the LGC board (1) Check if the connector CN332,CN334 is disconnected. (2) Check if the conductor pattern on the board is short circuited or open circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) "5", "6" , "7" , "8" , "18" , "20" , "24" , "26" or "28" to "0" |
| Error code: | C471 |
| Description: | IH power voltage abnormality or IH initial abnormality (IH board initial abnormality) |
| Causes: | Duplexing unit interlock switch. Fuser unit Power supply IH board LGC board |
| Remedy: | 1. Check the AC input voltage Check if the AC input voltage is within the specified range. (especially when the heater becomes ON after the power is turned ON (the copier is warming up)) 2. Check the thermostat Check if the thermostat is blown. 3. Check the IH control board (1) Check if the AC input connector on the IH control board, the LGC I/F connectors CN455 is disconnected? (2) Check if the fuse on the IH control board has blown. (3) Replace the IH control board. 4. Check the LGC board (1) Check if the connector CN332,CN334 and CN360 are disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 5. Check the switching regurator Check if the connector CN414 are disconnected. 6. Clear the status counter Change the values "10", "11", "12", "13"or "16" of the status counter (08-400) to "0". |
| Error code: | C472 |
| Description: | IH power voltage abnormality (power supply abnormality) |
| Causes: | Duplexing unit interlock switch. Fuser unit Power supply IH board LGC board |
| Remedy: | 1. Check the AC input voltage Check if the AC input voltage is within the specified range. (especially when the heater becomes ON after the power is turned ON (the copier is warming up)) 2. Check the thermostat Check if the thermostat is blown. 3. Check the IH control board (1) Check if the AC input connector on the IH control board, the LGC I/F connectors CN455 is disconnected? (2) Check if the fuse on the IH control board has blown. (3) Replace the IH control board. 4. Check the LGC board (1) Check if the connector CN332,CN334 and CN360 are disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 5. Check the switching regurator Check if the connector CN414 are disconnected. 6. Clear the status counter Change the values "10", "11", "12", "13"or "16" of the status counter (08-400) to "0". |
| Error code: | C473 |
| Description: | IH power voltage abnormality (power voltage upper limit abnormality) |
| Causes: | Power supply IH board |
| Remedy: | 1. Check the AC input voltage Check if the AC input voltage is within the specified range. (especially when the heater becomes ON after the power is turned ON (the copier is warming up)) 2. Check the thermostat Check if the thermostat is blown. 3. Check the IH control board (1) Check if the AC input connector on the IH control board, the LGC I/F connectors CN455 is disconnected? (2) Check if the fuse on the IH control board has blown. (3) Replace the IH control board. 4. Check the LGC board (1) Check if the connector CN332,CN334 and CN360 are disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 5. Check the switching regurator Check if the connector CN414 are disconnected. 6. Clear the status counter Change the values "10", "11", "12", "13"or "16" of the status counter (08-400) to "0". |
| Error code: | C474 |
| Description: | IH power voltage abnormality (power voltage lower limit abnormality) |
| Causes: | Power supply IH board |
| Remedy: | 1. Check the AC input voltage Check if the AC input voltage is within the specified range. (especially when the heater becomes ON after the power is turned ON (the copier is warming up)) 2. Check the thermostat Check if the thermostat is blown. 3. Check the IH control board (1) Check if the AC input connector on the IH control board, the LGC I/F connectors CN455 is disconnected? (2) Check if the fuse on the IH control board has blown. (3) Replace the IH control board. 4. Check the LGC board (1) Check if the connector CN332,CN334 and CN360 are disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 5. Check the switching regurator Check if the connector CN414 are disconnected. 6. Clear the status counter Change the values "10", "11", "12", "13"or "16" of the status counter (08-400) to "0". |
| Error code: | C475 |
| Description: | IH power voltage abnormality (power supply abnormality when door is opened) |
| Causes: | Side cover interlock switch. LGC board FIL board IH board Power supply |
| Remedy: | 1. Check the AC input voltage Check if the AC input voltage is within the specified range. (especially when the heater becomes ON after the power is turned ON (the copier is warming up)) 2. Check the thermostat Check if the thermostat is blown. 3. Check the IH control board (1) Check if the AC input connector on the IH control board, the LGC I/F connectors CN455 is disconnected? (2) Check if the fuse on the IH control board has blown. (3) Replace the IH control board. 4. Check the LGC board (1) Check if the connector CN332,CN334 and CN360 are disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 5. Check the switching regurator Check if the connector CN414 are disconnected. 6. Clear the status counter Change the values "10", "11", "12", "13"or "16" of the status counter (08-400) to "0". |
| Error code: | C480 |
| Description: | IH abnormality |
| Causes: | IH board cooling fan-1/-2 IH board LGC board |
| Remedy: | 1. Check the IH control board and LGC board (1) Check if the conductor pattern on the board is short- or open-circuited. (2) Replace the IH control board. (3) Replace the LGC board. (4) Check if the harnesses connecting the IH board and LGC board are open circuited. 2. Clear the status counter Change the values "15" of the status counter (08-400) to "0". |
| Error code: | C481 |
| Description: | IGBT abnormality |
| Causes: | IH board LGC board |
| Remedy: | 1. Check the operation of the IH fan Check if the IH fan is rotating normally. (Is the connector securely connected?) 2. Check the IH control board (1) Check if the IGBT or IGBT radiation plate are normal. (Is the radiation plate securely attached?) (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the IH control board. 3. Clear the status counter Change the values "14" of the status counter (08-400) to "0". |
| Error code: | C490 |
| Description: | IH control circuit abnormality or IH coil abnormality: The IH control circuit is under abnormal conditions, or the IH coil is broken or has a short-circuit. |
| Causes: | IH board LGC board |
| Remedy: | 1. Check the power voltage Is the voltage normal? (Is the voltage during the operation ±10% of the rated voltage?) 2. Check the IH control board (1) Check if the harness of IH coil is loosened. (2) Check if the conductor pattern on the board is short circuited or open circuited. (3) Replace the IH control board. 3. Check the IH coil (1) Check if the coil is broken or shorted. (2) Replace the IH coil. 4. Clear the status counter Change the current status counter value (08-400) "17" to "0". [C47X], [C481] and [C490] can be cleared by turning OFF and ON the main switch as long as the problem was solved, and the status counter does not have to be changed to "0". The value of the status counter remains until the next service call overwrites the value. |
| Error code: | C4A0 |
| Description: | End of cleaning web |
| Remedy: | (1) Check if the cleaning web is remaining. (2) Check if the connector CN332 on the LGC board is not disconnected. (3) Check if there is no abnormality at the web sensor. (4) Replace the LGC board. |
| Error code: | C4B0 |
| Description: | Fuser unit counter abnormality |
| Causes: | LGC board |
| Remedy: | 1. Check the LGC board (1) Check if the conductor pattern on the board is short circuited or open circuited. (2) Check if NVRAM is mounted. (3) Replace the LGC board. 2. Clear the status counter Change the current status counter value (08-400) "30 or more" or "4" to "0". |
| Error code: | C550 |
| Description: | RADF interface error: Communication error has occurred between the RADF and the scanner. |
| Causes: | RADF board Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-3210). SLG board |
| Remedy: | (1) Check if the harness connecting the ADF board and SLG board is disconnected or open circuited. (2) Check if the conductor pattern on the ADF board is short circuited or open circuited. (3) Check if the conductor pattern on the SLG board is short circuited or open circuited. (4) Replace the ADF board. (5) Replace the SLG board. |
| Error code: | C560 |
| Description: | Communication error between Engine-CPU and PFC |
| Causes: | PFC board LGC board |
| Remedy: | (1) Check if the conductor pattern around IC57 and IC58 on LGC board is not short- or opencircuited. (2) Replace the LGC board. |
| Error code: | C570 |
| Description: | Communication error between Engine-CPU and IPC board |
| Causes: | LGC board |
| Remedy: | (1) Check if the LGC board and IPC board are connected properly. (2) Check if the conductor pattern on the IPC board is short circuited or open circuited. (3) Check if the conductor pattern on the LGC board is short circuited or open circuited. (4) Replace the IPC board. (5) Replace the LGC board. |
| Error code: | C580 |
| Description: | Communication error between IPC board and Finisher |
| Causes: | LGC board Finisher controller board |
| Remedy: | (1) Check if the specified finisher is attached. (2) Check if the harness connecting the IPC board and the finisher controller PC board is disconnected or open circuited. (3) Check if the conductor pattern on the IPC board is short circuited or open circuited. (4) Check if the conductor pattern on the finisher controller PC board is short circuited or open circuited. (5) Replace the IPC board. (6) Replace the finisher controller PC board. |
| Error code: | C590 |
| Description: | Communication error between Engine-CPU and Laser-CPU |
| Remedy: | (1) Check if the harness between the LGC board and PLG board is not disconnected or opencircuited. (2) Check if the conductor pattern around IC13, IC58, IC125 and CN342 on the LGC board is not short circuited or open circuited. (3) Check if the conductor pattern around IC9, IC25, IC32 and CN204 on the PLG board is not shortor opencircuited. (4) Check if the connector CN104 on the SYS board and CN130, CN133 on the SYSIF board is disconnected. (5) Replace the LGC board. (6) Replace the PLG board. (7) Replace the SYSIF board |
| Error code: | C730 |
| Description: | RADF EEPROM error: Data abnormality occurs during the EEPROM writing of the RADF is performed. |
| Causes: | RADF board Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-3210). |
| Remedy: | 1. Check the IC-1, -2 and around on the RADF board to see if there is any burnout or shortcircuiting. 2. Replace the Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). |
| Error code: | C820 |
| Description: | Read sensor adjustment error: The read sensor cannot be adjusted normally when the code 05-356 is performed. |
| Remedy: | (1) Check if there is any foreign matter between the read sensor and the reflecting mirror. Check if the reflecting mirror is dirty. (2) Check if the harness connecting the read sensor and the ADF board is open circuited. (3) Check the circuits and connectors on the ADF board, mainly IC6, IC11 and CN11 and CN15, for short circuits and open circuits. (4) Replace the read sensor. (5) Replace the ADF board. |
| Error code: | C830 |
| Description: | Original length detection sensor adjustment error: The original length detection sensor cannot be adjusted normally when the code 05-356 is performed. |
| Causes: | A shutter unit error is detected. |
| Remedy: | (1) Check if there is any foreign matter between the original length detection sensor and reflecting mirror. Check if the reflecting mirror is dirty. (2) Check if the harness connecting the original length detection sensor and the ADF board is open circuited. (3) Check the circuits and connectors on the ADF board, mainly IC6, IC11 and CN15, for short circuits and open circuits. (4) Replace the original length detection sensor. (5) Replace the ADF board. |
| Error code: | C840 |
| Description: | Small original reverse sensor adjustment error: The small original reverse sensor cannot be adjusted normally when the code 05-356 is performed. |
| Causes: | A backup RAM data error is detected. |
| Remedy: | Is there any extraneous material between the small original reverse sensor and reflective mirror? → YES . Remove the extraneous material. NO Is the reflective mirror tainted? → YES . Clean up the mirror. NO Is the conductor pattern around IC6, IC11 and CN16 on the ADF board short- or open-circuited? → YES . Replace the ADF board. NO Replace the small original reverse sensor. |
| Error code: | C850 |
| Description: | Tray lift motor abnormality |
| Causes: | Defective mailbox drive motor or mailbox main PCB. |
| Remedy: | Is the lifting tray lifted when originals are set on the feeding tray? ↓ → NO . Is the loading of the lifting tray normal? l → NO . Adjust the mechanical loading. Remove, if any, extraneous materials. YES Is the power voltage for CN5-5 and CN6 on the ADF board 24V? → NO . Replace the ADF board. YES Replace the lifting tray motor. YES Is the lifting tray upper limit detection sensor working properly when the lifting tray is lifted? → NO . Replace the lifting tray upper limit detection sensor. YES Is the lifting tray lowered when originals are removed from the original tray? ↓ → NO . ↓ → NO . Is the loading of the lifting tray abnormal, adjust the mechanical loading. Remove, if any, extraneous materials. YES YES 1) Replace the lifting tray lower limit detection sensor. 2) Replace the ADF board. |
| Error code: | C860 |
| Description: | Large original exit sensor adjustment error: The large original exit sensor cannot be adjusted normally when the code 05-356 is performed. |
| Remedy: | Is there any extraneous material between the large original exit sensor and reflective mirror? → YES . Remove the extraneous material. NO Is the reflective mirror tainted? → YES . Clean up the mirror. NO Is the conductor pattern around IC6, IC11 and CN11 on the ADF board short circuited or open circuited? ll → YES . 1) Replace the ADF board. 2) Perform the sensor automatical adjustment of ADF and tray width sensor adjustment. NO 1) Replace the large original exit sensor. 2) Perform the sensor automatical adjustment of ADF |
| Error code: | C870 |
| Description: | Temperature detection error |
| Remedy: | Check if the conductor pattern around thermistor(TH1) on the ADF board is not short circuited or open circuited. Replace the ADF board. |
| Error code: | C940 |
| Description: | Engine-CPU abnormality |
| Causes: | LGC board |
| Remedy: | Is the “Call for Service” displayed even after the power is turned OFF and back ON? → NO → Leave it and see what happens. YES 1. Check if the circuit pattern between the Engine-CPU and FROM is short circuited or open circuited. 2. Replace the LGC board if this error occurs frequently. |
| Error code: | C970 |
| Description: | High-voltage transformer leakage abnormality: The high-voltage leakage of the main charger is detected. |
| Causes: | Main charger |
| Remedy: | (1) Is the main charger installed securely? (2) Check if the spring of high-voltage supply contact point is deformed. (3) Check if the main charger wire is broken or the main charger grid is deformed. (4) Check if any foreign matters is on the main charger win or the main charger grid. (5) Replace the High-voltage transformer. (6) Replace the LGC board. |
| Error code: | CA10 |
| Description: | Polygonal motor abnormality: The polygonal motor does not run normally. |
| Causes: | Polygonal motor Laser unit cooling fan (front) Laser unit cooling fan (rear) LGC board Laser optical unit |
| Remedy: | Is the polygonal motor rotating? ↓ → NO → (e-STUDIO555/655) 1. Check if the connector CN209 on the PLG board is disconnected. 2. Check if the harness is open circuited and the connector pin is disconnected. 3. Check if the following signals are transmitted on the pins of the connector CN209 on the PLG board. Pin 1: 27±1V, Pin 2: GND, Pin 5: Less than or equal to 1V (Lo), Pin 4: Less than or equal to 0.7 V (Lo), Pin 3: Do not touch. 4. Check if the conductor pattern on the PLG board is short circuited or open circuited. 5. Replace the laser optical unit. 6. Replace the PLG board. (e-STUDIO755/855) 1. Check if the connector CN206 on the PLG board is disconnected. 2. Check if the harness is open circuited and the connector pin is disconnected. 3. Check if the following signals are transmitted on the pins of the connector CN206 on the PLG board. Pin 5: 24±1V, Pin 4: GND, Pin 3: Less than or equal to 1V (Lo), Pin 2: Less than or equal to 0.7 V (Lo), Pin 1: Do not touch. 4. Check if the conductor pattern on the PLG board is short circuited or open circuited. 5. Replace the laser optical unit. 6. Replace the PLG board. YES Is the deformed image output? ↓ → NO → (e-STUDIO555/655) 1. Check if the connector CN209 on the PLG board is about to be disconnected. 2. Check if the harness is about to be open circuited and the connector pin is disconnected. 3. Check if the following signals are transmitted on the pins of the connector CN209 on the PLG board. Pin 1: 27±1V, Pin 2: GND, Pin 5: Less than or equal to 1V (Lo), Pin 4: Less than or equal to 0.7 V (Lo), Pin 3: Do not touch. 4. Check if the conductor pattern on the PLG board is short circuited or open circuited. 5. Check if the laser unit cooling fan is not stopped. 6. Check if the intake area of the laser unit cooling fan is not blocked. 7. Replace the laser optical unit. 8. Replace the PLG board. (e-STUDIO755/855) 1. Check if the connector CN206 on the PLG board is about to be disconnected. 2. Check if the harness is about to be open circuited and the connector pin is disconnected. 3. Check if the following signals are transmitted on the pins of the connector CN206 on the PLG board. Pin 5: 24±1V, Pin 4: GND, Pin 3: Less than or equal to 1V (Lo), Pin 2: Less than or equal to 0.7 V (Lo), Pin 1: Do not touch. 4. Check if the conductor pattern on the PLG board is short circuited or open circuited. 5. Check if the laser unit cooling fan is not stopped. 6. Check if the intake area of the laser unit cooling fan is not blocked. 7. Replace the laser optical unit. 8. Replace the PLG board. YES 1. Check if the conductor pattern on the PLG board is short circuited or open circuited. 2. Check if the grounding wire of the high-voltage unit (e.g. developer unit, transfer unit) is grounded securely. 3. Check if the bias contact point of the high-voltage unit is contacted securely. (Check if the point is not stained either.) 4. Check if the metal plates of the transport system are grounded securely. 5. Check if the equipment is grounded securely? 6. Check if the laser unit cooling fan is not stopped. 7. Check if the intake area of the laser unit cooling fan is not blocked. 8. Replace the laser optical unit. |
| Error code: | CA20 |
| Description: | H-sync detection error: Laser beam cannot be detected at the SNS board. |
| Causes: | LGC board Laser optical unit |
| Remedy: | (e-STUDIO555/655) Is the harness connecting the connector (J207) on the PLG board and the connector on the LDR1 board open circuited? Are the connectors damaged or disconnected? Is the harness connecting the connector (CN202) on the PLG board and the connector on the SNS board open circuited? Are the connectors damaged or disconnected? (e-STUDIO755/855) Is the harness connecting the connector (J207) on the PLG board and the connector on the LDR1 board open circuited? Are the connectors damaged or disconnected? Is the harness connecting the connector (J208) on the PLG board and the connector on the LDR1 board open circuited? Are the connectors damaged or disconnected? Is the harness connecting the connector (J210) on the PLG board and the connector on the SNS board open circuited? Are the connectors damaged or disconnected? ↓ → NO → (e-STUDIO555/655) 1. Replace the harness. Reconnect the connector. 2. Check if the connector(J207) on PLG board hold the harness securely? 3. Check if the following signals are transmitted on the pin of the connector(CN1) on the PLG board? Pin 1: 5V, Pin 3: 0V 4. Replace the laser optical unit. (e-STUDIO755/855) 1. Replace the harness. Reconnect the connector. 2. Check if the connector(J207,J208) on PLG board hold the harness securely? 3. Replace the laser optical unit. YES 1. Check if the conductor pattern on the PLG board is short circuited or open circuited. 2. Check if the grounding wire of the high-voltage unit (e.g. developer unit, transfer unit) is grounded securely. 3. Check if the bias contact point of the high-voltage unit is contacted securely. (Check if the point is not stained either.) 4. Check if the metal plates of the transport system are grounded securely. 5. Check if the equipment is grounded securely? 6. Replace the laser optical unit. |
| Error code: | CA30 |
| Description: | Secondary scanning coarse adjustment error |
| Remedy: | Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES → Replace the harness. Reconnect the connector. NO 1. Replace the PLG board. 2. Replace the laser optical unit. |
| Error code: | CA41 |
| Description: | Window comparator abnormality (error during secondary scanning control) |
| Remedy: | Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES → Replace the harness. Reconnect the connector. NO 1. Replace the PLG board. 2. Replace the laser optical unit. |
| Error code: | CA42 |
| Description: | Sensor signal busy error (error during secondary scanning control) |
| Remedy: | Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES → Replace the harness. Reconnect the connector. NO 1. Replace the PLG board. 2. Replace the laser optical unit. |
| Error code: | CA43 |
| Description: | Comparator abnormality |
| Remedy: | Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES → Replace the harness. Reconnect the connector. NO 1. Replace the PLG board. 2. Replace the laser optical unit. |
| Error code: | CA44 |
| Description: | Beam sensor detection error [e-STUDIO850] |
| Remedy: | Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES . Replace the harness. Reconnect the connector. NO 1) Replace the PLG board. 2) Replace the laser optical unit. |
| Error code: | CA50 |
| Description: | Laser power adjustment error |
| Remedy: | Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES → Replace the harness. Reconnect the connector. NO 1. Replace the PLG board. 2. Replace the laser optical unit. |
| Error code: | CA90 |
| Description: | Image data transmission error of SYS board: Communication error has occurred between the PLG board and the SYS board. |
| Remedy: | Is the harness between the PLG, SYSIF and SYS boards open-circuited or the connector disconnected? → YES → Replace the harness. Reconnect the connector. NO 1. Replace the PLG board. 2. Replace the SYS board. 3. Replace the SYSIF board. |
| Error code: | CAA0 |
| Description: | Secondary scanning fine adjustment error: Secondary scanning control by the galvanometer mirror does not end normally |
| Remedy: | Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES → Replace the harness. Reconnect the connector. NO 1. Replace the PLG board. 2. Replace the laser optical unit. |
| Error code: | CAB0 |
| Description: | Inter-page correction error of secondary scanning: Inter-page secondary scanning control by the galvanometer mirror does not end normally. |
| Remedy: | Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES → Replace the harness. Reconnect the connector. NO 1. Replace the PLG board. 2. Replace the laser optical unit. |
| Error code: | CAC0 |
| Description: | Primary scanning dot adjustment error: Primary scanning control does not end normally. |
| Remedy: | Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES → Replace the harness. Reconnect the connector. NO 1. Replace the PLG board. 2. Replace the laser optical unit. |
| Error code: | CAF0 |
| Description: | Inter-page correction error of primary scanning: Inter-page primary scanning control does not end normally. |
| Remedy: | Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES → Replace the harness. Reconnect the connector. NO 1. Replace the PLG board. 2. Replace the laser optical unit. |
| Error code: | CB10 |
| Description: | Feed motor abnormality: The feed motor does not run normally or the stack feed roller does not move normally. |
| Causes: | Entrance motor Finisher control board |
| Remedy: | [Procedure 1] Is second feed motor (M8) rotating in reverse at the fixed timing? → NO → Replace second feed motor or finisher controller PC board. YES Is the shutter securely attached to the shutter upper/lower bars? → NO → Attach it securely. YES Turn the feed roller-2 in reverse by hand. Do the shutter upper/lower bars move up and down? l → NO → Fix the mechanism including the shutter upper/lower bars and gears of the feed roller-2. YES Is the shutter closed detecting switch (MS4) working normally? → NO → Replace the switch. YES Replace the finisher controller PC board. [Procedure 2] Is second feed motor (M8) rotating in reverse at the fixed timing? → NO → Replace second feed motor or finisher controller PC board. YES Is the shutter securely attached to the shutter upper/lower bars? → NO → Attach it securely. YES Turn feed roller-2 in reverse by hand. Do the shutter upper/lower bars move up and down? l → NO → Fix the mechanism including the shutter upper/lower bars and gears of the feed roller-2. YES Is the shutter open sensor (PI5) working normally? → NO → Replace the sensor. YES Replace the finisher controller PC board. [Procedure 3] Check the safety zone switch (MS3). Is the switch working normally? → NO → Replace the switch. YES Is the safety zone switch (MS3) correctly pressed? → NO → Fix the mechanism. YES Is the shutter closed detecting switch (MS4) working normally? → NO → Replace the switch. YES Is the shutter closed detecting switch (MS4) correctly pressed? → NO → Fix the mechanism. YES Replace the finisher controller PC board. |
| Error code: | CB20 |
| Description: | Delivery motor abnormality: The delivery motor does not run normally or the delivery roller does not move normally. |
| Causes: | Exit motor clock sensor (PI10) Finisher controller circuit board Exit motor |
| Remedy: | Rotate the delivery motor by hand. Does it rotate smoothly? → NO → Fix the mechanism. YES Is the delivery motor clock sensor (PI10) working normally? → NO → Replace the sensor. YES MJ-1027/1028: Does the voltage between J11-4 and -5 on the finisher controller PC board become 24V when the delivery motor starts rotating? MJ-1029: Does the voltage between J11-1 and -2 on the finisher controller PC board become 24V when the delivery motor starts rotating? → NO → Replace the finisher controller PC board. YES Is the wiring between the delivery motor and finisher controller PC board correct? → YES → Correct the wiring. NO Replace the motor. |
| Error code: | CB30 |
| Description: | Tray lift motor abnormality |
| Causes: | Movable tray shift motor Movable tray position-A/-B/-C sensor Finisher control board |
| Remedy: | [Procedure 1] Is the tray 1 home position sensor (PI8) working properly? → NO → Replace the tray 1 home position sensor. YES Is the tray 1 lifting mechanism working properly? → NO → Correct the defect of the mechanism. YES Is 24V supplied to the tray1 lifting motor (M5) from the finisher control board at the timing of tray driving? → NO → Replace the finisher control board. YES Is the harness between the finisher control board and tray 1 lifting motor normal? → NO → Replace the harness. YES Replace the tray 1 lifting motor. [Procedure 2] Is the tray 1 lifted/lowered? ↓ → YES → Is the wiring between the finisher controller PC board and tray 1 lifting motor normal? → NO → Correct the wiring. YES Replace the tray 1 lifting motor. NO Is the power supplied to the motor from the finisher control board at the timing of tray 1 lifting? → NO → Replace the finisher control board. YES Correct the defect of the mechanism. [Procedure 3] Is the tray 2 home position sensor (PI25) working properly? → NO → Replace the tray 2 home position sensor. YES Is the tray 2 lifting mechanism working properly? → NO → Correct the defect of the mechanism. YES Is 24V supplied to the tray 2 lifting motor (M10) from the finisher control board at the timing of tray driving? → NO → Replace the finisher control board. YES Is the harness between the finisher control board and tray 2 lifting motor normal? → NO → Replace the harness. YES Replace the tray 2 lifting motor. [Procedure 4] Is the tray 2 lifted/lowered? ↓ → YES → Is the harness between the finisher control board and tray 2 lifting motor normal? → NO → Correct the wiring. YES Replace the tray 2 lifting motor. NO Is the power supplied to the motor from the finisher control board at the timing of tray 2 lifting? → NO → Replace the finisher control board. YES Is there any abnormality at the tray 2 lifting mechanism? → YES → Correct the defect of the mechanism. NO Replace the tray 2 lifting motor. [Procedure 5] Is the tray lifting mechanism working properly? → NO → Correct the defect of the mechanism. YES Is the tray coming close detection switch working properly? → NO → Replace the switch. YES Replace the finisher controller PC board. |
| Error code: | CB40 |
| Description: | Alignment motor (rear) abnormality: The alignment motor (rear) does not run normally or the alignment plate does not move normally |
| Causes: | Front alignment motor Finisher control board |
| Remedy: | Is the alignment guide home position sensor (PI6) working normally? → NO → Replace the sensor. YES Is the wiring between the finisher controller PC board and the alignment motor (M3) correct? → YES → Correct the wiring. NO Is there any mechanical problem with the alignment guide movement path? → YES → Fix the mechanism. NO Is the problem solved by replacing the alignment motor? → NO → Replace the finisher controller PC board. YES END |
| Error code: | CB50 |
| Description: | Staple motor abnormality: The staple motor does not run normally or the stapler does not move normally. |
| Causes: | Stapler Finisher control board |
| Remedy: | Is the wiring between the finisher controller PC board and the stapler normal? → NO → Correct the wiring. YES Is the problem solved by replacing the stapler? → YES → END NO Replace the finisher controller PC board. |
| Error code: | CB60 |
| Description: | Stapler shift motor abnormality: The stapler shift motor does not run normally or the Staple Unit does not move normally. |
| Causes: | Stapler Stapler unit shift motor Finisher control board |
| Remedy: | Is the stapler shift home position sensor (PI7) working normally? → NO → Replace the sensor. YES Is the wiring between the finisher controller PC board and the stapler shift motor (M4) correct? → YES → Correct the wiring. NO Is there any mechanical problem with the stapler stand motion path? → YES → Fix the mechanism. NO Try replacing the staple shift motor. Is the problem corrected? → YES → END NO Replace the finisher controller PC board. |
| Error code: | CB70 |
| Description: | Stack amount detection sensor abnormality |
| Remedy: | [Procedure 1] Is the problem solved by turning OFF and ON the power of the equipment? → YES → END NO Is the wiring between the finisher controller PC board and the height sensor (PS1) correct? → YES → Correct the wiring. NO Is the voltage between J6-2(+) and J6-4(-) on the finisher controller PC board 5V DC? → NO → Replace the finisher controller PC board. YES Re-adjust the height sensor. Replace the height sensor if it still causes the problem. [Procedure 2] Is the connector J6 on the finisher controller PC board, J114 of the height sensor (PS1) or relay connector J212 and J213 (Only for MJ-1027/1028) disconnected? → YES → Connect the connector(s). NO Is the voltage between J6-2(+) and J6-4(-) on the finisher controller PC board 5V DC? → NO → Replace the finisher controller PC board. YES Is the wiring between the finisher controller PC board and height sensor correct? → YES → Correct the wiring. NO Replace the height sensor. [Procedure 3] Is the problem solved by readjusting the DIP switch? → YES → END NO Is the wiring between the finisher controller PC board and height sensor (PS1) correct? → YES → Correct the wiring. NO Is the voltage between J6-2(+) and J6-4(-) on the finisher controller PC board 5V DC? → NO → Replace the finisher controller PC board. YES Replace the height sensor. |
| Error code: | CB80 |
| Description: | Backup RAM data abnormality: 1. Abnormality of checksum value on the finisher controller PC board is detected when the power is turned ON. 2. Abnormality of checksum value on the punch controller PC board is detected when the power is turned ON. |
| Causes: | Finisher control board |
| Remedy: | Is the problem solved by turning the power of the equipment OFF and ON? → YES → End. NO Replace the finisher controller PC board. Replace tha punch driver PC board. |
| Error code: | CB90 |
| Description: | Paper pushing plate motor abnormality: The paper pushing plate motor does not run normally or the paper pushing plate does not move normally. |
| Remedy: | [Procedure 1] Is the paper pushing plate home position sensor (PI14S) working normally? → NO → Replace the sensor. YES Is the paper pushing plate motor (M8S) operating at the fixed timing? → YES → Replace the saddle stitcher controller PC board. NO Is the paper pushing plate drive mechanism normal? → NO → Fix the mechanism. YES Is the problem solved by replacing the paper pushing plate motor (M8S)? → NO → Replace the saddle stitcher controller PC board. YES END [Procedure 2] Is the paper pushing plate top position sensor (PI15S) working normally? → NO → Replace the sensor. YES Is the paper pushing plate motor (M8S) operating at the fixed timing? → YES → Replace the saddle stitcher controller PC board. NO Is there any problem with the paper pushing plate drive mechanism? → YES → Fix the mechanism. NO Is the problem solved by replacing the paper pushing plate motor (M8S)? → NO → Replace the saddle stitcher controller PC board. YES END [Procedure 3] Is the paper pushing plate motor clock sensor (PI1S) working normally? → NO → Replace the sensor. YES Is the paper pushing plate motor (M8S) operating at the fixed timing? → YES → Replace the saddle stitcher controller PC board. NO Is there any problem with the pushing plate drive mechanism? → YES → Fix the mechanism. NO Is the problem solved by replacing the paper pushing plate motor (M8S)? → NO → Replace the saddle stitcher controller PC board. YES END |
| Error code: | CBA0 |
| Description: | Stitch motor (front) abnormality: The stitch motor (front) does not run normally or the rotational cam does not move normally. |
| Causes: | Stitcher home position switch Stitcher motor Saddle control PC board |
| Remedy: | Are the front and rear stitchers and their stands installed properly? → NO → Install them properly. YES Are the stitcher home position switches (MS7S/MS5S) on the front and rear stitchers working normally? → NO → Replace the front or rear stitcher. YES Are the front and rear stitchers operating at the fixed timing? → NO → Replace the front or rear stitcher. YES Check the wiring between the stitcher and saddle stitcher controller PC board. If there is no problem, replace the controller PC board. |
| Error code: | CBB0 |
| Description: | Stitch motor (rear) abnormality: The stitch motor (rear) does not run normally or the rotational cam does not move normally. |
| Causes: | Stitcher home position switch Stitcher motor Saddle control PC board |
| Remedy: | Are the front and rear stitchers and their stands installed properly? → NO → Install them properly. YES Are the stitcher home position switches (MS7S/MS5S) on the front and rear stitchers working normally? → NO → Replace the front or rear stitcher. YES Are the front and rear stitchers operating at the fixed timing? → NO → Replace the front or rear stitcher. YES Check the wiring between the stitcher and saddle stitcher controller PC board. If there is no problem, replace the controller PC board. |
| Error code: | CBC0 |
| Description: | Alignment motor abnormality: The alignment motor does not run normally or the alignment plate does not move normally. |
| Causes: | Alignment plate home position sensor Alignment motor Saddle control PC board |
| Remedy: | Is the alignment plate home position sensor (PI5S) working normally? → NO → Replace the sensor. YES Is the alignment motor (M5S) operating at the fixed timing? → YES → Replace the saddle stitcher controller PC board. NO Is the alignment plate drive mechanism normal? → NO → Fix the mechanism. YES Is the problem solved by replacing the alignment motor (M5S)? → NO → Replace the saddle stitcher controller PC board. YES END |
| Error code: | CBD0 |
| Description: | Guide motor abnormality: The guide motor does not run normally or the guide does not move normally. |
| Remedy: | Is the guide home position sensor (PI13S) working normally? → NO → Replace the sensor. YES Is the guide motor (M3S) operating at the fixed timing? → YES → Replace the saddle stitcher controller PC board. NO Is the guide plate drive mechanism normal? → NO → Fix the mechanism. YES Is the problem solved by replacing the guide motor (M3S)? → NO → Replace the saddle stitcher controller PC board. YES END |
| Error code: | CBE0 |
| Description: | Paper folding motor abnormality: The paper folding motor does not run normally or the paper folding roller does not move normally. |
| Causes: | Paper folding motor clock sensor Paper folding home position sensor Paper folding motor Saddle control PC board |
| Remedy: | Is the paper folding motor clock sensor (PI4S) working normally? → NO → Replace the sensor. YES Is the paper folding home position sensor (PI21S) working normally? → NO → Replace the sensor. YES Is the paper folding motor (M2S) operating at the fixed timing? → YES → Replace the saddle stitcher controller PC board. NO Is the paper folding roller drive mechanism normal? → NO → Fix the mechanism. YES Is the problem solved by replacing the paper folding motor (M2S)? → NO → Replace the saddle stitcher controller PC board. YES END |
| Error code: | CBF0 |
| Description: | Paper positioning plate motor abnormality: The paper positioning plate motor does not run normally or the paper positioning plate does not move normally. |
| Remedy: | Is the paper positioning plate home position sensor (PI7S) working normally? → NO → Replace the sensor. YES Is the paper positioning plate operating at the fixed timing? → YES → Replace the saddle stitcher controller PC board. NO Is the paper positioning plate drive mechanism normal? → NO → Fix the mechanism. YES Is the problem solved by replacing the paper positioning plate motor (M4S)? → NO → Replace the saddle stitcher controller PC board. YES END |
| Error code: | CC00 |
| Description: | Sensor connector abnormality: Disconnection of each connector of the guide home position sensor, paper pushing plate home position sensor and paper pushing plate leading position sensor is detected. |
| Remedy: | [Procedure 1] Is the guide home position sensor (PI13S) connected to the saddle stitcher controller PC board? → NO → Connect it to the board. YES Is the wiring between the sensor and the saddle stitcher correct? → YES → Correct the wiring. NO Is 5V DC being supplied from J9-7 on the saddle stitcher controller PC board? → NO → Replace the saddle stitcher controller PC board. YES Is J9-8 on the saddle stitcher controller PC board correctly connected to the ground? → NO → Replace the saddle stitcher controller PC board. YES END [Procedure 2] Is the paper pushing plate home position sensor (PI14S) connected to the saddle stitcher controller PC board? → NO → Connect it to the board. YES Is the wiring between the sensor and the saddle stitcher correct? → YES → Correct the wiring. NO Is 5V DC being supplied from J9-10 on the saddle stitcher controller PC board? → NO → Replace the saddle stitcher controller PC board. YES Is J9-11 on the saddle stitcher controller PC board properly connected to the ground? → NO → Replace the saddle stitcher controller PC board. YES END [Procedure 3] Is the paper pushing plate top position sensor (PI15S) connected to the saddle stitcher controller PC board? → NO → Connect it to the board. YES Is the wiring between the sensor and the saddle stitcher correct? → YES → Correct the wiring. NO Is 5V DC being supplied from J9-13 on the saddle stitcher controller PC board? → NO → Replace the saddle stitcher controller PC board. YES Is J9-14 on the saddle stitcher controller PC board properly connected to the ground? → NO → Replace the saddle stitcher controller PC board. YES END |
| Error code: | CC10 |
| Description: | Microswitch abnormality: Any of the inlet door switch, delivery door switch and front cover closing detection switch is opened while all the covers are closed. |
| Remedy: | [Procedure 1] Is the switch actuator for the inlet door working properly? → NO → Fix the mechanism. YES Is the inlet cover switch (MS1S) working normally? → NO → Replace the switch. YES Measure the voltage of J10-8 on the saddle stitcher controller PC board when the inlet door is open. Is it 5V? → NO → The inlet cover sensor (PI9S) is broken. Replace it. YES Measure the voltage between J1-1 (+) and J1-2 (-) on the saddle stitcher controller PC board. Is it 24 V? → NO → Replace the saddle stitcher controller PC board. YES Check the wiring between J19 on the finisher controller PC board and J1 on the saddle stitcher controller PC board. If there is no problem, replace the saddle stitcher controller PC board. [Procedure 2] Is the switch actuator for the front door working properly? → NO → Fix the mechanism. YES Is the front cover switch (MS2S) working normally? → NO → Replace the switch. YES Measure the voltage of J11-12 on the saddle switcher controller PC board when the front door is opened. Is it 5V? → NO → The front door opening/closing sensor is broken. Replace it. YES Replace the saddle stitcher controller PC board. [Procedure 3] Is the switch actuator for the delivery door working properly? → NO → Fix the mechanism. YES Is the delivery cover switch working normally? → NO → Replace the switch. YES Measure the voltage of J11-9 on the saddle stitcher controller PC board when the delivery door is opened. Is it 5V ? → NO → The delivery cover sensor (PI3S) is broken. Replace it. YES Replace the saddle stitcher controller PC board. |
| Error code: | CC20 |
| Description: | Communication error between Finisher and Saddle Stitch section: Communication error has occurred between the finisher controller PC board and the saddle stitcher controller PC board. |
| Causes: | Finisher control PC board Saddle control PC board |
| Remedy: | Is the problem solved by turning OFF and ON the power switch of the equipment? → YES → END NO Is the wiring between the finisher controller PC board and the saddle stitcher controller PC board connected? → YES → Connect the wiring. NO Measure the voltage between J3-2 (+) and J3-1 (-) on the finisher controller PC board. Is it DC 5V? → NO → Replace the finisher controller PC board. YES Replace the saddle stitcher controller PC board. |
| Error code: | CC40 |
| Description: | Swing motor abnormality: The swing motor does not run normally or the swing unit does not move normally. |
| Remedy: | [Procedure 1] Rotate the swing motor in reverse by hand. Does the swing guide move up and down? → NO → Fix the swing mechanism. YES Is the swing guide closed detection switch-2 (MS6) working normally? → NO → Replace the switch. YES Is the swing guide open sensor (PI18) working normally? → NO → Replace the sensor. YES Is the swing motor (M7) rotating in reverse at the fixed timing? → NO → Replace the motor. YES Replace the finisher controller PC board. [Procedure 2] Is the safety zone switch (MS3) working normally? → NO → Replace the switch. YES Is the safety zone switch (MS3) correctly pressed? → NO → Fix the mechanism. YES Is the swing guide closed detection switch-2 (MS6) working normally? → NO → Replace the switch. YES Is the swing guide closed detection switch-2 (MS6) correctly pressed? → NO → Fix the mechanism. YES Replace the finisher controller PC board. [Procedure 3] Is the swing motor clock sensor (PI20) working normally? → NO → Replace the sensor. YES MJ-1027/1028: Does the voltage between J11-6 and -7 on the finisher controller PC board become 24V when the swing motor starts rotating? MJ-1029: Does the voltage between J9-6 and -7 on the finisher controller PC board become 24V when the swing motor starts rotating? → NO → Replace the finisher controller PC board. YES Is the wiring between the swing motor and finisher controller PC board correct? → YES → Correct the wiring. NO Replace the swing motor. |
| Error code: | CC50 |
| Description: | Horizontal registration motor abnormality: The horizontal registration motor does not run normally or the puncher does not move normally. |
| Remedy: | Is the horizontal registration home position sensor (PI1P) working normally? → NO → Replace the sensor. YES Is the wiring between the finisher controller PC board and horizontal registration home position sensor (PI1P) correct? → NO → Correct the wiring. YES Is there any problem with the horizontal registration mechanism? → YES → Fix the mechanism. NO Is the problem solved by replacing the horizontal registration motor (M2P)? → YES → END NO Is the problem solved by replacing the punch driver PC board? → YES → END NO Replace the finisher controller PC board. |
| Error code: | CC60 |
| Description: | Punch motor abnormality: The punch motor does not run normally or the puncher does not move normally. |
| Causes: | Punch home position sensor Punch motor clock sensor Punch motor Hole punch control PC board Finisher control PC board |
| Remedy: | Is the punch motor clock sensor ((PI2P) working normally? → NO → Replace the sensor. YES Is the punch home sensor (PI3P) working normally? → NO → Replace the sensor. YES Is the wiring between the punch home sensor (PI3P) and finisher controller PC board correct? → NO → Correct the wiring. YES Is the punching mechanism normal? → YES → Fix the mechanism. NO Is the problem solved by replacing the punch motor (M1P) ? → YES → END NO Is the problem solved by replacing the punch driver board? → YES → END NO Replace the finisher controller PC board. |
| Error code: | CCC1 |
| Description: | Communication error between Inserter Unit and Finisher |
| Remedy: | Is the harness between the finisher controller PC board and the inserter control board normal? → NO → Replace the harness. YES Is 5V output to CN13-5 on the inserter control board? → YES → Replace the finisher control board. NO Replace the inserter control board. |
| Error code: | CCD1 |
| Description: | Inserter EEPROM abnormality |
| Remedy: | Is the conductor pattern around IC5 on the inserter control board short- or open-circuited? → YES 1. Replace the inserter control board. 2. Perform the inserter tray volume adjustment. |
| Error code: | CCE1 |
| Description: | Inserter fan motor abnormality |
| Remedy: | Is the harness between the inserter control board and inserter fan normal? → NO → Replace the harness. YES Is the conductor pattern around Q11, Q16 and CN8 on the inserter control board short circuited or open circuited? → NO → Replace the inserter fan. YES Replace the inserter control board. |
| Error code: | CD00 |
| Description: | Laser initialization time-out: Laser control does not end within the initialization period. |
| Remedy: | Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES → Replace the harness. Reconnect the connector. NO 1. Replace the PLG board. 2. Replace the laser optical unit. |
| Error code: | CD10 |
| Description: | Cleaning brush drive motor abnormality: The cleaning brush drive motor does not run normally when the power is turned ON or the copying is started. |
| Remedy: | (1) Check if the cleaning brush, recovery toner transport auger and recycle toner transport auger are not locked (no extraneous material or toner clod in both the toner transport sections at the cleaner unit and recycle toner unit). (2) Is the cleaning brush drive motor (M13) disconnected? (3) Check if the connector (CN337) on the LGC board and connector pins are not disconnected. (4) Replace the cleaning brush drive motor and recycle toner transport motor (M8). (5) Replace the LGC board. |
| Error code: | CD20 |
| Description: | Used toner transport motor abnormality: The used toner transport motor does not run normally when the power is turned ON or the copying is started. |
| Remedy: | (1) Check if the transport auger is not locked (there is no extraneous material or toner clod). (2) Is the toner bag full detection sensor (S11) working normally? (3) Is the used toner transport motor (M9) disconnected? (4) Check if the connector (CN333) on the LGC board and connector pins are not disconnected. (5) Replace the used toner transport motor. (6) Replace the LGC board. |
| Error code: | CD30 |
| Description: | Recycle toner transport motor abnormality: The recycle toner transport motor does not run normally when the power is turned ON or the copying is started. |
| Remedy: | (1) Check if the recycle toner transport auger is not locked (no extraneous material or toner clod in both the transport sections at the toner recycle unit). (2) Is the Recycle toner transport motor (M8) disconnected? (3) Check if the connector (CN337) on the LGC board and connector pins are not disconnected. (4) Replace the recycle toner transport motor. (5) Replace the LGC board. |
| Error code: | CD40 |
| Description: | Toner bag full |
| Causes: | Copy Process related service call Waste toner box full is detected. |
| Remedy: | (1) Check the toner bag. • Is the toner bag full? (2) Check thetoner bag full detection sensor (S11). • Is the tone full detection sensor working properly? • Is the connector not disconnected? (3) Check the used toner transport motor. • Is the used toner transport motor driving? • Does the pulley beside the motor become heavy when it is turned toward the direction of arrow (counterclockwise)? (4) Replace the LGC board. (5) Release the status counter. • Turn the power ON while pressing both the [0] and [8] keys. • Press the [START] key after inputting [476] with digital keys. • Change the status counter "1", "2" or "3" to "0" and press the [SET] or [INTERRUPT] key ([CD4] released). • Check if the copier becomes to a standby state normally when power is turned ON again. • In case that the used toner transport motor does not drive or [CD4] is not released when power is turned ON again, do the above procedure after manually turning the pulley beside the motor toward the direction of arrow (counterclockwise) several times. |
| Error code: | CD50 |
| Description: | Web motor signal path abnormality |
| Remedy: | (1) Check if the connector of the web motor and connector pins are not disconnected. (2) Check if the harness at the fuser unit is not open-circuited. (3) Check if the connector of the LGC board and connector pins are not disconnected. (4) Check if the harness between the connector of the LGC board and the fuser unit is not open circuited. (5) Replace the LGC board. (6) Replace the fuser unit. |
| Error code: | CE50 |
| Description: | Temperature/humidity sensor abnormality: The output value of the temperature/humidity sensor is out of the specified range. |
| Causes: | Temperature/humidity sensor LGC board |
| Remedy: | Is the connector CN338 on the LGC board or the connector of the temperature/humidity sensor (S7) disconnected? Is the harness between the LGC board and the temperature/humidity sensor disconnected? → YES → Connect the connector securely. Replace the harness. NO 1. Check the connection of the KEY board and DSP board. 2. Check the connection of the DSP board and LGC board. 3. Replace the temperature/humidity sensor. 4. Replace the LGC board. |
| Error code: | CE90 |
| Description: | Drum thermistor abnormality: The output value of the drum thermistor is out of the specified range. |
| Causes: | Drum thermistor-K Drum thermistor-Y EPU board LGC board |
| Remedy: | Is the connector CN337 on the LGC board, or the connector of the drum thermistor disconnected? Is the harness between the LGC board and the drum thermistor (THM5) disconnected? → YES → Connect the connector securely. Replace the harness. NO 1. Replace the drum thermistor. 2. Replace the LGC board. |
| Error code: | CF70 |
| Description: | New toner transport motor abnormality: The new toner transport motor does not run normally when new toner is supplied. |
| Remedy: | (1) Check if the transport auger and paddle are not locked (no extraneous material or toner clod in both the toner transport sections at the cleaner unit). (2) Is the new toner transport motor disconnected? (3) Check if the connector of the LGC board and connector Pins are not disconnected. (4) Replace the new toner transport motor. (5) Replace the LGC board. |
| Error code: | CF80 |
| Description: | Hopper motor lockup: The hopper motor does not run normally when the power is ON or the copying is started. |
| Remedy: | (1) Check if the recycle toner transport motor is not locked (no extraneous material or toner clod in both the toner transport sections at the recycle toner unit). (2) Is the disconnected? (3) Check if the connector of the LGC board and connector Pins are not disconnected. (4) Replace the hopper motor. (5) Replace the LGC board. |
| Error code: | E010 |
| Display: | E010 |
| Description: | Paper not reaching fuser transport sensor: Paper which has passed the fuser unit does not reach the fuser transport sensor. |
| Causes: | Fuser transport sensor LGC board ADU board PFC board Fuser unit |
| Remedy: | Open the jam access cover. Is there any paper on the transport path or in the fuser unit? → YES → Remove the paper. NO Is the fuser transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[7]/[C]) ↓ → NO → 1. Check if the connector of the fuser transport sensor is disconnected. 2. Check if the connector CN332 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the fuser transport sensor. 6. Replace the LGC board. YES Is the transfer belt working? ↓ → NO → 1. Check if the connector of the transport belt is disconnected. 2. Check if the connector on the transport motor driving PC board is disconnected. 3. Check if the connector CN341 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the transport motor driving PC board. 7. Replace the LGC board. YES Is the drum separation finger solenoid working? (Perform the output check in the test mode: 03-111,161) ↓ → NO → 1. Check if the connector of the drum separation finger solenoid is disconnected. 2. Check if the connector CN339 on the LGC board is disconnected. 3. Check the installation state of cleaner. 4. Is the relay connector connecting the cleaner unit and the equipment disconnected or stained with toner? 5. Replace the drum separation finger solenoid. 6. Replace the LGC board. YES Is the registration sensor working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the registration sensor is installed correctly. 3. Check if the registration actuator is operating properly. 4. Check if the connector CN341 on the LGC board is disconnected. 5. Check if the connector pins are disconnected and the harnesses are open circuited. 6. Check if the conductor pattern on the LGC board is short circuited or open circuited. 7. Replace the registration sensor. 8. Replace the LGC board. YES Is the registration motor working? (Perform the output check in the test mode: 03-108/158) ↓ → NO → 1. Check if the connector of the registration roller clutch is disconnected. 2. Check if the connector CN341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration roller clutch. 6. Replace the LGC board. YES Check if there is any abnormality in the space between the registration motor and the registration roller (metal). Check if the registration roller (rubber) is rotating smoothly. Check the condition of the registration roller at the horizontal transport section and clean or replace it. * If the error [E010] caused by a paper jam underneath the drum cleaner often occurs due to an insufficient paper separation from the photoconductive drum, set a smaller value in the code 08-841, and see what happens. At this time, however, pay attention to the transferability at the leading edge of the paper since this transferability can be slightly narrowed depending on the environments and conditions under which the equipment is placed or the media type of the paper used. (Refer to 3.6.1 in this manual about the details of the code 08-841.) |
| Error code: | E020 |
| Description: | Paper stopping at fuser transport sensor: The trailing edge of paper does not pass the fuser transport sensor after its leading edge has reached the fuser transport sensor. |
| Causes: | LGC board ADU board PFC board Rollers |
| Remedy: | Is the fuser transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[7]/[C]) ↓ → NO → 1. Check if the connector of the fuser transport sensor is disconnected. 2. Check if the connector CN332 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the fuser transport sensor. 6. Replace the LGC board. YES Is the reverse motor driving? (Perform the output check in the test mode: 03-126) ↓ → NO → 1. Check if the connector of the reverse transport unit is not disconnected. 2. Check if the connector CN335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check if the conductor pattern on the LGC board is not short- or open-circuited. 5. Replace the LGC board YES 1. Check if the separation finger for the fuser unit is working normally. 2. Replace the LGC board |
| Error code: | E030 |
| Description: | Power-ON jam: Paper is remaining on the paper transport path of the equipment when the power is turned ON. |
| Causes: | Fuser transport sensor LGC board ADU board PFC board Rollers |
| Remedy: | Open the cover of the unit/area whose picture is blinking on the control panel. Is there any paper on the transport path? (Refer to the following table.) → YES → Remove the paper. NO Is the sensor in the jamming area working? (Perform the input check in the test mode: refer to the following table.) ↓ → NO → 1. Check if the connector of the sensor is disconnected. 2. Check if any of the connectors on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the sensor. 6. Replace the LGC board. YES Replace the LGC board. Registration area Registration sensor 03-[FAX]ON/[4]/[E] Exit/Reverse area Exit sensor 03-[FAX]OFF/[7]/[B] Reverse sensor-1 03-[FAX]OFF/[7]/[E] Reverse sensor-2 03-[FAX]OFF/[7]/[D] Fuser transport sensor 03-[FAX]OFF/[7]/[C] Reverse transport area Horizontal transport sensor-1 03-[FAX]OFF/[9]/[F] Horizontal transport sensor-2 03-[FAX]OFF/[9]/[G] Horizontal transport sensor-3 03-[FAX]OFF/[9]/[H] Paper feeding area 1st drawer feed sensor 03-[FAX]OFF/[1]/[D] 2nd drawer feed sensor 03-[FAX]OFF/[2]/[D] 3rd drawer / tandem LCF feed sensor 03-[FAX]OFF/[3]/[D] 4th drawer feed sensor 03-[FAX]OFF/[4]/[D] 1st drawer transport sensor 03-[FAX]OFF/[1]/[C] 2nd drawer transport sensor 03-[FAX]OFF/[2]/[C] 3rd drawer / tandem LCF transport sensor 03-[FAX]OFF/[3]/[C] 4th drawer transport sensor 03-[FAX]OFF/[4]/[C] Intermediate transport sensor 03-[FAX]OFF/[1]/[A] |
| Error code: | E061 |
| Description: | Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment. |
| Remedy: | If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON. |
| Error code: | E062 |
| Description: | Incorrect paper size setting for 2nd drawer: The size of paper in the 2nd drawer differs from size setting of the equipment. |
| Remedy: | If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON. |
| Error code: | E063 |
| Description: | Incorrect paper size setting for 3rd drawer: The size of paper in the 3rd drawer differs from size setting of the equipment. |
| Remedy: | If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON. |
| Error code: | E064 |
| Description: | Incorrect paper size setting for 4th drawer: The size of paper in the 4th drawer differs from size setting of the equipment. |
| Remedy: | If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON. |
| Error code: | E065 |
| Display: | E065 error X motor |
| Description: | Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment. |
| Remedy: | If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON. |
| Error code: | E090 |
| Description: | Image data delay jam: Image data to be printed cannot be prepared. |
| Causes: | SYS board IMG board LGC board HDD Page memory |
| Remedy: | 1. Remove the paper remained in front of the registration sensor. 2. If the error still occurs, check the following: 3. Check if the error is cleared by turning the power OFF and then back ON. 4. Check if the connectors connecting the SYS board, SLG board and PLG board are disconnected. 5. Check if the connectors of the HDD are disconnected. 6. Check if the page memory is connected to the connector on the SYS board properly. 7. Replace the page memory. 8. Check if the harnesses connecting the SYS board, SLG board and PLG board are opencircuited. 9. Replace the HDD, SYS board, SLG board and PLG board. |
| Error code: | E110 |
| Description: | Transport jam during duplex printing (paper not reaching registration sensor): Paper which passed the reverse transport section does not reach the registration sensor during duplex printing. |
| Causes: | Registration sensor ADU motor2 ADU board PFC board LGC board ADU roller |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the registration sensor? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Is the transport motor (M17) rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. YES Check the transport roller. Clean or replace it. (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → If the paper is damaged, remove the paper and check the followings. 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ll → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) NO → Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. Replace the registration roller(rubber) if not solved. |
| Error code: | E120 |
| Description: | Bypass misfeeding (paper not reaching registration sensor): Paper fed out of the bypass tray does not reach the registration sensor. |
| Causes: | Bypass feed sensor Bypass motor Bypass pick-up solenoid ADU board PFC board ADU roller Rollers |
| Remedy: | Open the bypass unit cover. Is there any paper in front of the registration sensor? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Is the width of the side guides of the bypass unit too narrow? Is the paper skewed? → YES → Match the width of the side guides and that of the paper. NO Is the bypass feed clutch working? (Perform the output check in the test mode: 03-204) Is the bypass feed sensor working? (Perform the input check in the test mode: 03- [FAX]OFF/[6]/[G]) ↓ → NO → 1. Check if the connector of the bypass feed clutch and bypass feed sensor are disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the bypass feed clutch and bypass feel sensor. 6. Replace the LGC board. YES Check the bypass transport roller, feed separation and separation rollers. Clean or replace them. |
| Error code: | E130 |
| Description: | 1st drawer misfeeding (paper not reaching 1st drawer feed sensor): Paper does not reach the 1st drawer feed sensor during the feeding at the 1st drawer. |
| Causes: | 1st drawer feed sensor Feed motor PFC roller Rollers |
| Remedy: | Open the feed cover. Is there any paper in front of the 1st drawer transport sensor? → YES → Remove the paper. NO Is the 1st drawer feed sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[D]) ↓ → NO → 1. Check if the connector of the 1st drawer feed sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer feed sensor. 6. Replace the LGC board. YES Is the width of the side guides of the 1st drawer too narrow? Is there any paper skewing? → YES → Fit the width of the original guide to that of the paper. NO Is the 1st drawer feed clutch working? (Perform the output check in the test mode: 03-201) ↓ → NO → 1. Check if the connector of the 1st drawer feed clutch is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer feed clutch. 6. Replace the LGC board. YES Check the 1st drawer feed roller, separation roller and pickup roller. Clean or replace them. * Check if the paper weight is within the specified range. |
| Error code: | E140 |
| Description: | 2nd drawer misfeeding (paper not reaching 2nd drawer feed sensor): Paper does not reach the 2nd drawer feed sensor during the feeding at the 2nd drawer. |
| Causes: | 2nd drawer feed sensor Feed motor PFC roller Rollers |
| Remedy: | Open the drawer feed cover. Is there any paper in front of the 2nd drawer transport sensor? → YES → Remove the paper. NO Is the 2nd drawer transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[D]) ↓ → NO → 1. Check if the connector of the 2nd drawer feed sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 2nd drawer feed sensor. 6. Replace the LGC board. YES Is the width of the side guides of the 2nd drawer too narrow? Is there any paper skewing? → YES → Fit the width of the original guide to that of the paper. NO Is the 2nd drawer feed clutch working? (Perform the output check in the test mode: 03-202) ↓ → NO → 1. Check if the connector of the 2nd drawer feed clutch is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 2nd drawer feed clutch. 6. Replace the LGC board. YES Check the 2nd drawer feed roller, separation roller and pickup roller. Clean or replace them. * Check if the paper weight is within the specified range. |
| Error code: | E150 |
| Description: | 3rd drawer misfeeding (paper not reaching 3rd drawer / Tandem LCF feed sensor): Paper does not reach the 3rd drawer / Tandem LCF feed sensor during the feeding at the 3rd drawer. |
| Causes: | 3rd drawer feed sensor Feed/transfer motor PFC roller Rollers 3rd drawer feed clutch |
| Remedy: | Open the feed cover. Is there any paper in front of the 3rd drawer / Tandem LCF feed sensor? → YES → Remove the paper. NO Is the 3rd drawer / Tandem LCF feed sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[3]/[D]) ↓ → NO → 1. Check if the connector of the 3rd drawer / Tandem LCF feed sensor is disconnected. 2. Check if the connector CN328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 3rd drawer / Tandem LCF feed sensor. 6. Replace the LGC board. YES Is the width of the side guides of the 3rd drawer too narrow? Is there any paper skewing? → YES → Fit the width of the original guide to that of the paper. NO Is the 3rd drawer / Tandem LCF feed clutch working? (Perform the output check in the test mode: 03-209 (Tandem LCF model) and 03-226 (4th drawer model)) ↓ → NO → 1. Check if the connector of the 3rd drawer / Tandem LCF feed clutch is disconnected. 2. Check if the connector CN328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 3rd drawer / Tandem LCF feed clutch. 6. Replace the LGC board. YES Check the 3rd drawer / Tandem LCF feed roller, separation roller and pickup roller. Clean or replace them. * Check if the paper weight is within the specified range. |
| Error code: | E160 |
| Description: | 4th drawer misfeeding (paper not reaching 4th drawer feed sensor): Paper does not reach the 4th drawer feed sensor during the feeding at the 4th drawer. |
| Causes: | 4th drawer feed sensor Feed/transfer motor PFC roller Rollers 4th drawer feed clutch |
| Remedy: | Open the feed cover. Is there any paper in front of the 4th drawer feed sensor? → YES → Remove the paper. NO Is the 4th drawer feed sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[4]/[D]) ↓ → NO → 1. Check if the connector of the 4th drawer feed sensor is disconnected. 2. Check if the connector CN350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 4th drawer feed sensor. 6. Replace the LGC board. YES Is the width of the side guides of the 4th drawer too narrow? Is there any paper skewing? → YES → Fit the width of the original guide to that of the paper. NO Is the 4th drawer feed clutch working? (Perform the output check in the test mode: 03-228) ↓ → NO → 1. Check if the connector of the 4th drawer feed clutch is disconnected. 2. Check if the connector CN350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 4th drawer feed clutch. 6. Replace the LGC board. YES Check the 4th drawer feed roller, separation roller and pickup roller. Clean or replace them. * Check if the paper weight is within the specified range. |
| Error code: | E180 |
| Description: | Option LCF misfeeding (paper not reaching Option LCF feed sensor): Paper does not reach the Option LCF feed sensor during the feeding at the Option LCF. |
| Causes: | LCF feed sensor LCF transport motor PFC board LCF board Rollers LCF transport clutch |
| Remedy: | Open the LCF front cover. Is there any paper in front of the LCF feed sensor? → YES → Remove the paper. NO Is the LCF feed sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[5]/[D]) ↓ → NO → 1. Check if the connector of the LCF feed sensor is disconnected. 2. Check if either of the connector J851 on the LCF board is disconnected. 3. Check if the connector J850 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 6. Replace the LCF feed sensor. 7. Replace the LCF board. 8. Replace the LGC board. YES Is the external LCF transport motor driving? (Perform the output check in the test mode: 03-122/172) ll → NO → 1. Check if the connector of the transport motor is not disconnected. 2. Check if the connector J854 on the board are not disconnected. 3. Check if there is any abnormality at the transport drive unit. YES Is the LCF feed clutch working? (Perform the output check in the test mode: 03-272) ↓ → NO → 1. Check if the connector of the LCF feed clutch is disconnected. 2. Check if any of the connector J851 on the LCF board is disconnected. 3. Check if the connector CN346 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 6. Replace the LCF feed clutch. 7. Replace the LCF board. 8. Replace the LGC board. YES 1. Check if there is any abnormality at the transport drive unit. 2. Check the LCF feed roller, separation roller and pickup roller. Clean or replace them. * Check if the paper weight is within the specified range. |
| Error code: | E190 |
| Description: | Tandem LCF misfeeding (paper not reaching 3rd drawer / Tandem LCF feed sensor): Paper does not reach the 3rd drawer Tandem LCF feed sensor during the feeding at the Tandem LCF. |
| Causes: | LCF feed sensor LCF feed clutch PFC board Rollers |
| Remedy: | Open the feed cover. Is there any paper in front of the 3rd drawer / Tandem LCF feed sensor? → YES → Remove the paper. NO Is the 3rd drawer / Tandem LCF feed sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[3]/[D]) ↓ → NO → 1. Check if the connector of the 3rd drawer / Tandem LCF feed sensor is disconnected. 2. Check if the connector CN328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 3rd drawer / Tandem LCF feed sensor. 6. Replace the LGC board. YES Is the width of the side guides of the 3rd drawer too narrow? Is there any paper skewing? → YES → Fit the width of the original guide to that of the paper. NO Is the 3rd drawer / Tandem LCF feed clutch working? (Perform the output check in the test mode: 03-209 (Tandem LCF model) and 03-226 (4th drawer model)) ↓ → NO → 1. Check if the connector of the 3rd drawer / Tandem LCF feed clutch is disconnected. 2. Check if the connector CN328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 3rd drawer / Tandem LCF feed clutch. 6. Replace the LGC board. YES Check the 3rd drawer / Tandem LCF feed roller, separation roller and pickup roller. Clean or replace them. * Check if the paper weight is within the specified range. |
| Error code: | E200 |
| Description: | 1st drawer transport jam (paper not reaching registration sensor): Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the 1st drawer. |
| Causes: | Registration sensor Transport motor-1 PFC board LGC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the registration sensor? → YES → Replace the paper. NO Is the registration sensor(S18) working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES 1. Check the transport roller. Replace it if it is worn out. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor (S17) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor (M17) rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. 7. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. Check if the registration roller (rubber) is rotating smoothly. |
| Error code: | E201 |
| Description: | 1st drawer transport jam (paper not reaching intermediate transport sensor): Paper which has passed the 1st drawer transport sensor does not reach the intermediate transport sensor during the feeding at the 1st drawer. |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings. 1. Check if the connector of the intermediate transport sensor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Is the 1st drawer transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connector of the 1st drawer transport clutch is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport clutch. 6. Replace the LGC board. Check if the spring of the follower roller of the intermediate transport roller is working properly. (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → If the paper is damaged, remove the paper and check the followings. 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ll → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E210 |
| Description: | 2nd drawer transport jam (paper not reaching registration sensor): Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the 2nd drawer. |
| Causes: | Registration sensor Transport motor-1 PFC board LGC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the registration sensor? → YES → Replace the paper. NO Is the registration sensor(S18) working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES 1. Check the transport roller. Replace it if it is worn out. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor (S17) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor (M17) rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. 7. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. Check if the registration roller (rubber) is rotating smoothly. |
| Error code: | E211 |
| Description: | 2nd drawer transport jam (paper not reaching intermediate transport sensor): Paper which has passed the 1st drawer transport sensor does not reach the intermediate transport sensor during the feeding at the 2nd drawer. |
| Causes: | The scanning lamp thermistor has an open circuit. |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings. 1. Check if the connector of the intermediate transport sensor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Is the 1st drawer transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connector of the 1st drawer transport clutch is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport clutch. 6. Replace the LGC board. Check if the spring of the follower roller of the intermediate transport roller is working properly. (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → If the paper is damaged, remove the paper and check the followings. 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ll → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E220 |
| Description: | 2nd drawer transport jam (paper not reaching 1st drawer transport sensor): Paper which has passed the 2nd drawer transport sensor does not reach the 1st drawer transport sensor during the feeding at the 2nd drawer. |
| Causes: | 1st drawer transport sensor Transport motor-2 Transport motor-1 PFC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the 1st drawer transport sensor? → YES → Remove the paper. NO Is the 1st drawer transport sensor (S33) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[C]) ↓ → NO → 1. Check if the connector of the 1st drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches (CLT5,7,9,11) working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings: 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E230 |
| Description: | 1st drawer transport jam (paper not reaching 1st drawer transport sensor): Paper which has passed the 1st drawer feed sensor does not reach the 1st drawer transport sensor during the feeding at the 1st drawer. |
| Causes: | 1st drawer transport sensor Transport motor-1 Feed motor PFC board Rollers |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings.) 1. Check if the connector of the transport sensor is disconnected. 2. Check if the connector on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the LGC board. YES Is the reversed paper transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are opencircuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → Is there any damage on the paper? (Remove the paper and check the followings.) 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the actuator of the sensor is working normally. 3. Check if the harness is not damaged. 4. Check if the connector is disconnected. YES Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary. |
| Error code: | E240 |
| Display: | E240 error No SIMMs |
| Description: | 2nd drawer transport jam (paper not reaching 2nd drawer transport sensor): Paper which has passed the 2nd drawer feed sensor does not reach the 2nd drawer transport sensor during the feeding at the 2nd drawer. |
| Causes: | 2nd drawer transport sensor Transport motor-2 Feed motor PFC board Rollers |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings.) 1. Check if the connector of the transport sensor is disconnected. 2. Check if the connector on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the LGC board. YES Is the reversed paper transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are opencircuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → Is there any damage on the paper? (Remove the paper and check the followings.) 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the actuator of the sensor is working normally. 3. Check if the harness is not damaged. 4. Check if the connector is disconnected. YES Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary. |
| Error code: | E250 |
| Description: | Option LCF transport jam (paper not reaching Option LCF transport sensor): Paper does not reach the Option LCF transport sensor during the feeding at the Option LCF. |
| Causes: | • Front Cover Switch (S1) • Front Cover Open/Close Sensor Switch (S2) • Right Cover Switch (S3) • Right Cover Open/Close Sensor (PC27) • Power Supply (PU1) • Control Board (PWB-A) |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings.) 1. Check if the connector of the transport sensor is disconnected. 2. Check if the connector on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the LGC board. YES Is the reversed paper transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are opencircuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → Is there any damage on the paper? (Remove the paper and check the followings.) 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the actuator of the sensor is working normally. 3. Check if the harness is not damaged. 4. Check if the connector is disconnected. YES Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary. |
| Error code: | E260 |
| Description: | Option LCF transport jam (paper not reaching registration sensor): Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the Option LCF. |
| Causes: | Registration sensor Transport motor-1 PFC board LGC board Rollers |
| Remedy: | Is there any paper before the registration sensor when the bypass unit cover is opened? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the registration sensor connector is not disconnected. 2. Check if the connector J341 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check if the conductor pattern on the LGC board is not short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Is the external LCF transport motor driving? (Perform the output check in the test mode: 03-122/172) ↓ → NO → 1. Check if the connector of the transport motor is not disconnected. 2. Check if the connectors J854 on the LCF board are not disconnected. 3. Check if there is any abnormality at the transport drive unit. YES Is the external LCF feed clutch working? (Perform the output check in the test mode: 03-272) ↓ → NO → 1. Check if the external LCF clutch connector is not disconnected. 2. Check if the connectors J851 on the LCF board are not disconnected. 3. Check if the connector CN346 on the LGC board is not disconnected. 4. Check if the connector pins are not disconnected and the harness is not open circuited. 5. Check if the conductor pattern on the LCF and LGC boards is not short circuited or open circuited. 6. Replace the external LCF feed clutch. 7. Replace the LCF board. 8. Replace the LGC board. YES Is the external LCF transport clutch working? (Perform the output check in the test mode: 03-273) ↓ → NO → 1. Check if the connector of the external LCF feed clutch is not disconnected. 2. Check if the connectors J851 on the LCF board are not disconnected. 3. Check if the connector CN346 on the LGC board is not disconnected. 4. Check if the connector pins are not disconnected and the harness is not open circuited. 5. Check if the conductor pattern on the LCF and LGC boards is not short circuited or open circuited. 6. Replace the external LCF feed clutch. 7. Replace the LCF board. 8. Replace the LGC board. YES Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → Is there any damage on the paper? (Remove the paper and check the followings.) 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the actuator of the sensor is working normally. 3. Check if the harness is not damaged. 4. Check if the connector is disconnected. YES 1. Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary. 2. Check if there is any abnormality at the transport drive unit. 3. Check the condition of the external LCF feed roller and separation roller and clean or replace them. Check if the registration roller (rubber) is rotating smoothly. |
| Error code: | E261 |
| Description: | Option LCF transport jam (paper not reaching intermediate transport sensor): Paper which has passed the 1st drawer transport sensor does not reach the intermediate transport sensor during the feeding at the Option LCF. |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings. 1. Check if the connector of the intermediate transport sensor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Is the 1st drawer transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connector of the 1st drawer transport clutch is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport clutch. 6. Replace the LGC board. Check if the spring of the follower roller of the intermediate transport roller is working properly. (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → If the paper is damaged, remove the paper and check the followings. 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ll → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E2A1 |
| Description: | Transport jam during duplex printing (paper not reaching intermediate transport sensor): Paper which has passed the reverse section and horizontal transport section does not reach the intermediate transport sensor during duplex printing |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings. 1. Check if the connector of the intermediate transport sensor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Is the 1st drawer transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connector of the 1st drawer transport clutch is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport clutch. 6. Replace the LGC board. Check if the spring of the follower roller of the intermediate transport roller is working properly. (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → If the paper is damaged, remove the paper and check the followings. 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ll → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E300 |
| Description: | 3rd drawer transport jam (paper not reaching registration sensor): Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the 3rd drawer. |
| Causes: | Registration sensor Transport motor-1 PFC board LGC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the registration sensor? → YES → Replace the paper. NO Is the registration sensor(S18) working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES 1. Check the transport roller. Replace it if it is worn out. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor (S17) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor (M17) rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. 7. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. Check if the registration roller (rubber) is rotating smoothly. |
| Error code: | E301 |
| Description: | 3rd drawer transport jam (paper not reaching intermediate transport sensor): Paper which has passed the 1st drawer transport sensor does not reach the intermediate transport sensor during the feeding at the 3rd drawer. |
| Causes: | • Fusing Unit • DC Power Supply (PU1) • Mechanical Control Board (PWB-M) |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings. 1. Check if the connector of the intermediate transport sensor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Is the 1st drawer transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connector of the 1st drawer transport clutch is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport clutch. 6. Replace the LGC board. Check if the spring of the follower roller of the intermediate transport roller is working properly. (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → If the paper is damaged, remove the paper and check the followings. 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ll → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E310 |
| Description: | 3rd drawer transport jam (paper not reaching 1st drawer transport sensor): Paper which has passed the 2nd transport sensor does not reach the 1st drawer transport sensor during the feeding at the 3rd drawer. |
| Causes: | 1st drawer transport sensor Transport motor-2 Transport motor-1 PFC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the 1st drawer transport sensor? → YES → Remove the paper. NO Is the 1st drawer transport sensor (S33) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[C]) ↓ → NO → 1. Check if the connector of the 1st drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches (CLT5,7,9,11) working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings: 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E320 |
| Description: | 3rd drawer transport jam (paper not reaching 2nd drawer transport sensor): Paper which has passed the 3rd drawer / Tandem LCF transport sensor does not reach the 2nd drawer transport sensor during the feeding at the 3rd drawer. |
| Causes: | 3rd drawer transport clutch 2nd drawer transport sensor Feed motor PFC board Rollers |
| Remedy: | Open the feed cover. Is there paper in front of the 2nd drawer transport sensor? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the 2nd drawer transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[C] ↓ → NO → 1. Check if the connector of the 2nd drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 2nd drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-210/225/231) ↓ → NO → 1. Check if the connectors of the (lower/middle) transport clutches are disconnected. 2. Check if the connector CN329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the (lower/middle) transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. |
| Error code: | E330 |
| Description: | 4th drawer transport jam (paper not reaching registration sensor): Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the 4th drawer. |
| Causes: | Registration sensor Transport motor-1 PFC board LGC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the registration sensor? → YES → Replace the paper. NO Is the registration sensor(S18) working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES 1. Check the transport roller. Replace it if it is worn out. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor (S17) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor (M17) rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. 7. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. Check if the registration roller (rubber) is rotating smoothly. |
| Error code: | E331 |
| Description: | 4th drawer transport jam (paper not reaching intermediate transport sensor): Paper which has passed the 1st drawer transport sensor does not reach the intermediate transport sensor during the feeding at the 4th drawer. |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings. 1. Check if the connector of the intermediate transport sensor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Is the 1st drawer transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connector of the 1st drawer transport clutch is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport clutch. 6. Replace the LGC board. Check if the spring of the follower roller of the intermediate transport roller is working properly. (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → If the paper is damaged, remove the paper and check the followings. 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ll → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E340 |
| Description: | 4th drawer transport jam (paper not reaching 1st transport sensor): Paper which has passed the 2nd drawer transport sensor does not reach the 1st drawer transport sensor during the feeding at the 4th drawer. |
| Causes: | 1st drawer transport sensor Transport motor-2 Transport motor-1 PFC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the 1st drawer transport sensor? → YES → Remove the paper. NO Is the 1st drawer transport sensor (S33) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[C]) ↓ → NO → 1. Check if the connector of the 1st drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches (CLT5,7,9,11) working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings: 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E350 |
| Description: | 4th drawer transport jam (paper not reaching 2nd drawer transport sensor): Paper which has passed the 3rd drawer / Tandem LCF transport sensor does not reach the 2nd drawer transport sensor during the feeding at the 4th drawer. |
| Causes: | 3rd drawer transport clutch 2nd drawer transport sensor Feed motor PFC board Rollers |
| Remedy: | Open the feed cover. Is there paper in front of the 2nd drawer transport sensor? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the 2nd drawer transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[C] ↓ → NO → 1. Check if the connector of the 2nd drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 2nd drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-210/225/231) ↓ → NO → 1. Check if the connectors of the (lower/middle) transport clutches are disconnected. 2. Check if the connector CN329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the (lower/middle) transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. |
| Error code: | E360 |
| Description: | 4th drawer transport jam (paper not reaching 3rd drawer / Tandem LCF transport sensor): Paper which has passed the 4th drawer transport sensor does not reach the 3rd drawer / Tandem LCF transport sensor during the feeding at the 4th drawer. |
| Causes: | 4rd drawer transport clutch 3rd drawer transport sensor 3rd drawer transport clutch Feed motor PFC board Rollers |
| Remedy: | Open the feed cover. Is there any paper in front of the 3rd drawer / Tandem LCF feed sensor? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the 3rd drawer / Tandem LCF feed sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[D]) ↓ → NO → 1. Check if the connector of the 3rd drawer / Tandem LCF feed sensor is disconnected. 2. Check if the connector CN328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the LGC board is short circuited or open circuited. 5. Replace the 3rd drawer / Tandem LCF drawer feed sensor. 6. Replace the LGC board. YES Is the 4th drawer transport clutch working? (Perform the output check in the test mode: 03-225) ↓ → NO → 1. Check if the connector of the 4th drawer transport clutch is disconnected. 2. Check if the connector CN350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 5. Replace the 4th drawer transport clutch. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the PFP transport roller. Clean or replace it. |
| Error code: | E370 |
| Description: | 3rd drawer transport jam (paper not reaching 3rd drawer / Tandem LCF transport sensor): Paper which has passed the 3rd drawer / Tandem LCF feed sensor does not reach the 3rd drawer / Tandem LCF transport sensor during the feeding at the 3rd drawer. |
| Causes: | 3rd drawer transport sensor 3rd drawer transport clutch 3rd drawer feed clutch PFC board Rollers |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings.) 1. Check if the connector of the transport sensor is disconnected. 2. Check if the connector on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the LGC board. YES Is the reversed paper transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are opencircuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → Is there any damage on the paper? (Remove the paper and check the followings.) 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the actuator of the sensor is working normally. 3. Check if the harness is not damaged. 4. Check if the connector is disconnected. YES Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary. |
| Error code: | E380 |
| Description: | 4th drawer transport jam (paper not reaching 4th drawer transport sensor): Paper which passed the 4th drawer feed sensor does not reach the 4th drawer transport sensor during the feeding at the 4th drawer. |
| Causes: | 4th drawer transport sensor 4th drawer transport clutch 4th drawer feed clutch Feed/transport motor PFC board Rollers |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings.) 1. Check if the connector of the transport sensor is disconnected. 2. Check if the connector on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the LGC board. YES Is the reversed paper transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are opencircuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → Is there any damage on the paper? (Remove the paper and check the followings.) 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the actuator of the sensor is working normally. 3. Check if the harness is not damaged. 4. Check if the connector is disconnected. YES Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary. |
| Error code: | E3C0 |
| Description: | Tandem LCF transport jam (paper not reaching registration sensor): Paper which has passed the 1st transport sensor does not reach the registration sensor during the feeding at the Tandem LCF. |
| Causes: | Registration sensor Transport motor-1 PFC board LGC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the registration sensor? → YES → Replace the paper. NO Is the registration sensor(S18) working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES 1. Check the transport roller. Replace it if it is worn out. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor (S17) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor (M17) rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Replace the LGC board. 7. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. Check if the registration roller (rubber) is rotating smoothly. |
| Error code: | E3C1 |
| Description: | Tandem LCF transport jam (paper not reaching intermediate transport sensor): Paper which has passed the 1st transport sensor does not reach the intermediate transport sensor during the feeding at the Tandem LCF. |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings. 1. Check if the connector of the intermediate transport sensor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Is the 1st drawer transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connector of the 1st drawer transport clutch is disconnected. 2. Check if the connector CN305 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport clutch. 6. Replace the LGC board. Check if the spring of the follower roller of the intermediate transport roller is working properly. (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → If the paper is damaged, remove the paper and check the followings. 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A]) ll → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the harness is not damaged. 3. Check if the connector is disconnected. YES Is the transport motor rotating? (Perform the output check in the test mode: 03-133,183) ↓ → NO → Check if the bearing of the transportation roller is locked. Replace the transport motor. 1. Check if the connector of the transport motor is disconnected. 2. Check if the connector CN327 on the LGC board is disconnected. 3. Check if the connector on the transport motor driving PC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor pattern on the LGC board is short circuited or open circuited. 6. Check if the conductor pattern on the transport motor driving PC board is short circuited or open circuited. 7. Replace the LGC board. 8. Replace the transport motor driving PC board. YES Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E3D0 |
| Description: | Tandem LCF transport jam (paper not reaching 1st drawer transport sensor): Paper which has passed the 2nd drawer transport sensor does not reach the 1st drawer transport sensor during the feeding at the Tandem LCF. |
| Causes: | 1st drawer transport sensor Transport motor-2 Transport motor-1 PFC board Rollers |
| Remedy: | (First page of printing) Open the jam access cover. Is there paper in front of the 1st drawer transport sensor? → YES → Remove the paper. NO Is the 1st drawer transport sensor (S33) working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[C]) ↓ → NO → 1. Check if the connector of the 1st drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches (CLT5,7,9,11) working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. (Second page or later of printing) Open the jam access cover. Is there any paper on the transport path? ↓ → YES → If the paper is damaged, remove the paper and check the followings: 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. 5. Check the motor-related adjustment value. NO Check if the spring of the follower roller of the intermediate transport roller is working properly. |
| Error code: | E3E0 |
| Description: | Tandem LCF transport jam (paper not reaching 2nd transport sensor): Paper which has passed the 3rd drawer / Tandem LCF transport sensor does not reach the 2nd drawer transport sensor during the feeding at the Tandem LCF. |
| Causes: | 3rd drawer transport clutch 2nd drawer transport sensor Feed motor PFC board Rollers |
| Remedy: | Open the feed cover. Is there paper in front of the 2nd drawer transport sensor? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the 2nd drawer transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[C] ↓ → NO → 1. Check if the connector of the 2nd drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 2nd drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-210/225/231) ↓ → NO → 1. Check if the connectors of the (lower/middle) transport clutches are disconnected. 2. Check if the connector CN329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the (lower/middle) transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. |
| Error code: | E3F0 |
| Description: | Tandem LCF transport jam (paper not reaching 3rd drawer / Tandem LCF transport sensor): Paper which has passed the 3rd drawer / Tandem LCF feed sensor does not reach the 3rd drawer / Tandem LCF transport sensor during the feeding at the Tandem LCF. |
| Causes: | Tandem LCF transport sensor Tandem LCF transport clutch Tandem LCF feed clutch Feed/transport motor PFC board Rollers |
| Remedy: | (First page of printing) Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → Open the jam access cover. Remove the paper and check the followings.) 1. Check if the connector of the transport sensor is disconnected. 2. Check if the connector on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the LGC board. YES Is the reversed paper transport clutch working? (Perform the output check in the test mode: 03-210/225/229/230/231) ↓ → NO → 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector CN328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are opencircuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary (Second page or later of printing) Leading edge of paper not reaching the fuser exit sensor. ↓ → YES → Is there any damage on the paper? (Remove the paper and check the followings.) 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the intermediate transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[A], OFF/[1]/[C], OFF/[2]/[C], OFF/[3]/[C], OFF/[4]/[C]) ↓ → NO → 1. Are paper dusts accumulated on the intermediate transport sensor? 2. Check if the actuator of the sensor is working normally. 3. Check if the harness is not damaged. 4. Check if the connector is disconnected. YES Check the conditions of the feed roller, separation roller and pickup roller of the drawer in use, and replace them if necessary. |
| Error code: | E410 |
| Description: | Front cover open jam: The front cover has opened during printing. |
| Causes: | Front cover opening/closing switch LGC board |
| Remedy: | Is the front cover open? → YES → Remove the paper if there is any, then close the cover. NO Is the voltage of 24V being supplied from the power supply unit? (Perform the input check in the test mode: 03-[FAX] ON/[9]/[H]) ↓ → NO → 1. Check if the connector for 24 V power supply is disconnected. 2. Check if the connector CN344 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the LGC board. YES Replace the LGC board. |
| Error code: | E440 |
| Description: | Right lower cover (feed cover) open jam: The feed cover has opened during printing. |
| Causes: | ADU opening/closing switch LGC board |
| Remedy: | Is the feed cover open? → YES → Remove the paper if there is any, then close the cover. NO Is the side door switch working? (Perform the input check in the test mode: 03-[FAX]ON/[2]/[A]) ↓ → NO → 1. Check if the connector of the feed cover sensor is disconnected. 2. Check if the connector CN304 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the feed cover sensor. 6. Replace the LGC board. YES Replace the LGC board. |
| Error code: | E450 |
| Description: | Option LCF side cover open jam: The side cover of the Option LCF has opened during printing. |
| Causes: | LCF side cover opening/closing switch LCF board LGC board |
| Remedy: | Is the LCF front cover open? → YES → Remove the paper if there is any, then close the cover. NO Is the LCF side cover opening/closing switch working? (Perform the input check in the test mode: 03-[FAX]OFF/[5]/[B]) ↓ → NO → 1. Check if the connector of the LCF side cover opening/closing switch is disconnected. 2. Check if either of the connectors CN100 or CN106 on the LCF board is disconnected. 3. Check if the connector CN338 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 6. Replace the LCF side cover opening/closing switch. 7. Replace the LCF board. 8. Replace the LGC board. YES 1. Replace the LCF board. 2. Replace the LGC board. |
| Error code: | E460 |
| Description: | Right center cover (bypass feed unit cover) open jam: The bypass feed unit cover has opened during printing. |
| Remedy: | Is the bypass feed unit cover open? → YES → Remove the paper if there is any, then close the bypass feed unit cover. NO Is the bypass feed unit cover sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[6]/[H]) ↓ → NO → 1. Check if the connector of the bypass feed unit cover sensor is disconnected. 2. Check if the connector CN338 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or opencircuited. 5. Replace the bypass feed unit cover sensor. 6. Replace the LGC board. YES Replace the LGC board. |
| Error code: | E470 |
| Description: | Left lower cover (exit cover) open jam: The exit cover has opened during printing. |
| Remedy: | Is the exit cover close? → YES → Remove paper if there is any, then close the cover. NO Is the voltage of 24V being supplied from the power supply unit? (Perform the input check in the test mode: 03-[FAX] ON/[9]/[H]) ↓ → NO → 1. Check if the connector for 24V power supply is disconnected. 2. Check if the connector CN344 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the LGC board. YES Is the exit cover switch working? (Perform the input check in the test mode: 03-[FAX]OFF/[7]/[A] ↓ → NO → 1. Check if the connector of the exit cover switch is disconnected. 2. Check if the connector CN335 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short- or opencircuited. 5. Replace the exit cover switch. 6. Replace the LGC board. YES Replace the LGC board. |
| Error code: | E510 |
| Description: | Transport jam during duplex printing (paper not reaching reverse sensor-2): Paper which has passed the reverse sensor-1 does not reach the reverse sensor-2 during duplex printing. |
| Causes: | Duplexing unit path entrance sensor Reverse motor ADU motor-2 PFC board ADU board DRV board Rollers |
| Remedy: | Open the exit cover. Is there any paper in front of the reverse sensor-2? → YES → Remove the paper. NO Is the reverse sensor-1 working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[G]) ↓ → NO → 1. Check if the connector of the reverse sensor-1 is disconnected. 2. Check if the connector CN335 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor patterns on LGC board are short circuited or open circuited. 5. Replace the reverse sensor-1. 6. Replace the LGC board. YES Is the horizontal transport section driving clutch working? (Perform the output check in the test mode: 03-222) ↓ → NO → 1. Check if the connector of the horizontal transport section driving clutch is disconnected. 2. Check if the connector CN334 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the horizontal transport section driving clutch. 6. Replace the LGC board. YES Is the Mylar at the reverse section normal? → NO → Replace the Mylar. YES Check the condition of the roller at the horizontal transport section and clean or replace it. |
| Error code: | E511 |
| Description: | Transport jam during duplex printing (paper not reaching horizontal transport sensor-1): Paper which has passed the reverse sensor-2 does not reach the horizontal transport sensor-1 during duplex printing. |
| Causes: | Duplexing unit path entrance sensor Reverse motor ADU motor-1 PFC board ADU board Rollers |
| Remedy: | Is there any paper at the reverse section when the exit cover is opened? → YES → Remove the paper. NO Is the Horizontal transport sensor-1 working? (Perform the input check in the test mode: 03-[FAX]OFF/[9]/[F]) ↓ → NO → 1. Check if the connector of the Horizontal transport sensor-1 is not disconnected. 2. Check if the connector CN334 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check if the conductor pattern on the LGC board is not short circuited or open circuited. 5. Replace the Horizontal transport sensor-1. 6. Replace the LGC board. YES Is the transport roller 1/2 at the horizontal transport section rotating? (Perform the output check in the test mode: 03-110/220) ↓ → NO → 1. Check if the connectors of the and horizontal transport section driving clutch-1 and horizontal transport section driving clutch-2 are not disconnected. 2. Check if the connectors of the and horizontal transport section driving clutch-1 and and horizontal transport section driving clutch-2 are not misconnected (drive clutch: black-black, transport clutch 1: bluepurple). 3. Check if the connector CN334 on the LGC board is not disconnected. 4. Check if the connector pins are not disconnected and the harness is not open circuited. 5. Check if the conductor pattern on the LGC board is not short- or open circuited. 6. Replace the transport drive clutch and transport clutch 1. 7. Replace the LGC board. 8. Check if the front side timing belt is put on properly. 9. Check the installation state of the horizontal transport section driving clutch-1. YES Check the condition of the rollers at the horizontal transport section and clean or replace them. |
| Error code: | E512 |
| Description: | Transport jam during duplex printing (paper not reaching horizontal transport sensor-2): Paper which has passed the horizontal transport sensor-1 does not reach the horizontal transport sensor-2 during duplex printing. |
| Remedy: | Is there any paper at the reverse section when the exit cover is opened? → YES → Remove the paper. NO Is the Horizontal transport sensor-2 working? (Perform the input check in the test mode: 03-[FAX]OFF/[9]/[G]) ↓ → NO → 1. Check if the connector of the Horizontal transport sensor-2 is not disconnected. 2. Check if the connector CN334 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check if the conductor pattern on the LGC board is not short- or open-circuited. 5. Replace the Horizontal transport sensor-2. 6. Replace the LGC board. YES Is the transport roller 3/4 at the horizontal transport section rotating? (Perform the output check in the test mode: 03-110/221) ↓ → NO → 1. Check if the connectors of the horizontal transport section driving clutch-1 and horizontal transport section driving clutch-3 are not disconnected. 2. Check if the connectors of the horizontal transport section driving clutch-1 and horizontal transport section driving clutch-3 are not misconnected (drive clutch: black-black, transport clutch 2: blackblue) 3. Check if the connector CN334 on the LGC board is not disconnected. 4. Check if the connector pins are not disconnected and the harness is not open circuited. 5. Check if the conductor pattern on the LGC board is not short- or open-circuited. 6. Replace the and horizontal transport section driving clutch-1 and and horizontal transport section driving clutch-2. 7. Replace the LGC board. 8. Check if the front side timing belt is put on properly. YES Check the condition of the rollers at the horizontal transport section and clean or replace them |
| Error code: | E540 |
| Description: | Transport jam during duplex printing (paper not reaching horizontal transport sensor-3): Paper which has passed the horizontal transport sensor-2 does not reach the horizontal transport sensor-3 during duplex printing. |
| Causes: | Duplexing unit path exit sensor ADU motor-1 ADU motor-2 PFC board ADU board Rollers |
| Remedy: | (Perform the input check in the test mode: 03-[FAX]OFF/[9]/[H]) ↓ → NO → 1. Check if the connector of the Horizontal transport sensor-3 is not disconnected. 2. Check if the connector CN334 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check is the conductor pattern on the LGC board is not short- or open-circuited. 5. Replace the Horizontal transport sensor-3. 6. Replace the LGC board. YES Check the condition of the roller at the horizontal transport section and clean or replace it. |
| Error code: | E550 |
| Description: | Paper remaining jam at paper transport path: Paper is remaining on the paper transport path when the printing has finished. (Jam caused by a multiple paper feeding) |
| Causes: | Feed or transport roller possibly causing multiple feeding Sensor in the jamming area Refer to the table below PFC board |
| Remedy: | Open the cover of the unit/area whose picture is blinking on the control panel. Is there any paper on the transport path? → YES → Remove the paper. NO Is the sensor in the jamming area working? (Perform the input check in the test mode: refer to the following table) ↓ → NO→ 1. Check if the connector of the sensor is disconnected. 2. Check if any of the connectors on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the sensor. 6. Replace the LGC board. YES 1. Check if any multiple paper is fed from the drawer. 2. Replace the LGC board. Registration area Registration sensor 03-[FAX]ON/[4]/[E] Exit/Reverse area Exit sensor 03-[FAX]OFF/[7]/[B] Reverse sensor-1 03-[FAX]OFF/[7]/[E] Reverse sensor-2 03-[FAX]OFF/[7]/[D] Fuser transport sensor 03-[FAX]OFF/[7]/[C] Reverse transport area Horizontal transport sensor-1 03-[FAX]OFF/[9]/[F] Horizontal transport sensor-2 03-[FAX]OFF/[9]/[G] Horizontal transport sensor-3 03-[FAX]OFF/[9]/[H] Paper feeding area 1st drawer feed sensor 03-[FAX]OFF/[1]/[D] 2nd drawer feed sensor 03-[FAX]OFF/[2]/[D] 3rd drawer / tandem LCF feed sensor 03-[FAX]OFF/[3]/[D] 4th drawer feed sensor 03-[FAX]OFF/[4]/[D] 1st drawer transport sensor 03-[FAX]OFF/[1]/[C] 2nd drawer transport sensor 03-[FAX]OFF/[2]/[C] 3rd drawer / tandem LCF transport sensor 03-[FAX]OFF/[3]/[C] 4th drawer transport sensor 03-[FAX]OFF/[4]/[C] Intermediate transport sensor 03-[FAX]OFF/[1]/[A] |
| Error code: | E570 |
| Description: | Transport jam during duplex printing (paper not reaching reverse sensor-1): Paper which has passed the fuser unit transport sensor does not reach the reverse sensor-1 during duplex printing. |
| Causes: | Reverse sensor Transport entrance motor Fuser motor DFV board PFC board Rollers |
| Remedy: | Is there any paper before the registration sensor when the exit cover is opened? → NO → Remove the paper. YES Is the reverse sensor 1 working? (Perform the input check in the test mode: 03-[FAX]OFF/[7]/[E]) ↓ → NO → 1. Check if the connector of the reverse sensor-1 is not disconnected. 2. Check if the connector CN335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check if the conductor pattern on the LGC board is not short- or open circuited. 5. Replace the reverse sensor-1. 6. Replace the LGC board. YES Is the reverse motor driving? (Perform the output check in the test mode: 03-126) ↓ → NO → 1. Check if the connector of the reverse transport unit is not disconnected. 2. Check if the connector CN335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check if the conductor pattern on the LGC board is not short- or open-circuited. 5. Replace the reverse moter. 6. Replace the LGC board YES Is the gate solenoid working? (Perform the output check in the test mode: 03-274) ↓ → NO → 1. Check if the connector of the gate solenoid is not disconnected. 2. Check if the connector CN335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check if the conductor pattern on the LGC board is not short- or open-circuited. 5. Replace the gate solenoid. 6. Replace the LGC board YES 1. Check if there is no mechanical loading at the exit/reversal gate. 2. Check the myler at the reverse section and clean or replace it. |
| Error code: | E580 |
| Description: | Paper stopping at reverse section: The trailing edge of paper does not pass the reverse sensor-1 or reverse sensor-2 after its leading edge has reached the reverse sensor-1 or reverse sensor-2. |
| Causes: | Reverse sensor Reverse motor Bridge unit transport exit motor DFV board PFC board Rollers |
| Remedy: | Is there any paper at the reverse section when the exit cover is opened? → NO → YES Is the reverse sensor- 1/2 working? (Perform the input check in the test mode: 03-[FAX]OFF/[7]/[D], [7]/[E]) ↓ → NO → 1. Check if the connector of the reverse sensor 1/2 is not disconnected. 2. Check if the connector CN335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check if the conductor pattern on the LGC board is not short- or open-circuited. 5. Replace the reverse sensor- 1/2. 6. Replace the LGC board. YES 1. Check if the setting of the paper size is correct. 2. Check the condition of the roller at the reverse section and clean or replace it. 3. Check if there is no mechanical loading at the follower roller and no abnormality at the myler. 4. Check if the adjustment of the reverse motor speed (05-453/454/456) is appropriate. 5. Replace the reverse sensor-2 if it is drastically damaged. |
| Error code: | E590 |
| Description: | Paper stopping at exit section: The trailing edge of paper does not pass the exit sensor after its leading edge has reached the exit sensor. |
| Causes: | Upper paper exit sensor Exit motor PFC board DRV board LGC board |
| Remedy: | Is there any paper at the reverse section when the exit cover is opened? → NO → Remove the paper. YES Is the exit motor driving? (Perform the output check in the test mode: 03-120) ↓ → NO → 1. Check if the connector of the exit motor is not disconnected. 2. Check if the connector CN336 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the LGC board. YES 1. Check if the setting of the paper size is correct. 2. Check if there is no abnormality and extraneous material at the guide and myler in front of the exit roller. 3. Check if there is no mechanical loading at the exit follower roller. |
| Error code: | E5A0 |
| Description: | Paper not reaching exit sensor: The leading edge of paper does not reach the exit sensor. |
| Causes: | Upper paper exit sensor exit motor PFC board DRV board LGC board |
| Remedy: | Is the exit sensor working? (Perform the input check in the test mode: 03-[FAX]ON/ [1]/[C]) ↓ → NO → 1. Check if the connector of the exit sensor is not disconnected. 2. Check if the connector CN335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check if the conductor pattern on the LGC board is not short- or open circuited. 5. Replace the exit sensor. 6. Replace the LGC board. YES <Simple discharging> Is the gate solenoid working? (Perform the output check in the test mode: 03-274) ↓ → NO → 1. Check if the connector of the gate solenoid is not disconnected. 2. Check if the connector CN335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open circuited. 4. Check if the conductor pattern on the LGC board is not short- or open circuited. 5. Replace the LGC board. YES Replace the LGC board. <Reversal discharging> 1. Check if the setting of the paper size is correct. 2. Check if there is no abnormality and extraneous material at the guide and myler in front of the exit roller. * Perform 05-447 for thick paper to increase the value by 2 to 4. |
| Error code: | E711 |
| Description: | Original not reaching original length detection sensor: An original fed out of the original feeding tray does not reach the original length detection sensor. |
| Remedy: | Are the pickup roller, feed roller and separation roller stained or worn out? ↓ YES → Clean the rollers or replace them. NO Is the transport force of the rollers insufficient? ↓ YES → Replace the rollers. NO Is the original excessively curled or folded? ↓ NO → Replace the rollers. YES Flatten and set it again. |
| Error code: | E712 |
| Description: | Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor. |
| Causes: | Original registration sensor Original pickup solenoid RADF board Perform the 05-3210 Roller Pickup roller, feed roller, separation roller |
| Remedy: | 1. Clean the pickup roller, feed roller and separation roller if they are stained. 2. Flatten the original if it is folded or excessively curled and place it again. 3. Is the original registration sensor working? (Perform the input check: 03-[FAX]ON/[7]/[H]) * If it is working properly, proceed to 7. If not, check 3 to 6. 4. Check if the connector CN74 on the RADF board is disconnected from the original registration sensor or the harnesses are open circuited. Correct if any. 5. Replace the original registration sensor. 6. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 7. Replace the pickup roller, feed roller and separation roller if they are worn out. |
| Error code: | E713 |
| Description: | Original stopping at original length detection sensor: The trailing edge of the original does not pass the original length detection sensor after its leading edge has reached the original length detection sensor. |
| Remedy: | Are the registration roller, read roller and exit roller stained? ↓ YES Clean the rollers |
| Error code: | E714 |
| Description: | Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray. |
| Causes: | Original empty sensor RADF board Perform the 05-3210 Roller Pickup roller, feed roller, separation roller |
| Remedy: | 1. Is the original empty sensor working? (Perform the input check: 03-[FAX]ON/[7]/[B]) 2. Check if the lever of original empty sensor is working normally. 3. Check if the connector CN74 on the RADF board is disconnected from the original empty sensor or the harnesses are open circuited. Correct if any. 4. Replace the original empty sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). |
| Error code: | E715 |
| Description: | Tray lifting movement time-out: The lifting tray does not reach the lifting tray upper limit detection sensor. |
| Remedy: | Is there any foreign matter which interrupts lifting or lowering the tray? ↓ YES → Remove the foreign matter. NO Is the connector of the tray lift motor or the connector CN5 on the ADF board disconnected? ↓ YES → Reconnect the connector. NO Is the harness connecting the ADF board and tray lift motor open circuited? ↓ YES → Replace the harness. NO Is the connector CN12 or CN15 on the ADF board disconnected? ↓ YES → Reconnect the connector. NO Are the harnesses connecting the ADF board and the lifting tray upper limit detection sensor or the lifting tray lower limit detection sensor open circuited? ↓ YES → Replace the harness. NO Replace the ADF board. |
| Error code: | E716 |
| Description: | Tray lowering movement time-out: The lifting tray does not reach the lifting tray lower limit detection sensor. |
| Remedy: | Is there any foreign matter which interrupts lifting or lowering the tray? ↓ YES → Remove the foreign matter. NO Is the connector of the tray lift motor or the connector CN5 on the ADF board disconnected? ↓ YES → Reconnect the connector. NO Is the harness connecting the ADF board and tray lift motor open circuited? ↓ YES → Replace the harness. NO Is the connector CN12 or CN15 on the ADF board disconnected? ↓ YES → Reconnect the connector. NO Are the harnesses connecting the ADF board and the lifting tray upper limit detection sensor or the lifting tray lower limit detection sensor open circuited? ↓ YES → Replace the harness. NO Replace the ADF board. |
| Error code: | E721 |
| Description: | Jam not reaching the original reading start sensor: The original does not reach the original reading start sensor after it has passed the original registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side). |
| Causes: | Original reading start sensor RADF board Perform the 05-3210 Roller Registration roller, Read roller |
| Remedy: | 1. Clean the original registration roller, intermediate transfer roller, reading start roller, reverse roller and reverse registration roller if they are stained. 2. Is the original reading start sensor working? (Perform the input check: 03-[FAX]ON/[7]/[G]) * If it is working properly, proceed to 8. If not, check 3 to 7 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original reading start sensor or the harnesses are open circuited. Correct if any. 4. Perform the automatic adjustment of the original reading start sensor (05-356). 5. Perform the manual adjustment of the original reading start sensor. 6. Replace the original reading sensor, and then perform the automatic adjustment of the original reading start sensor (05-356). 7. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 8. Replace the original registration roller, intermediate transfer roller, reading start roller, reverse roller and reverse registration roller if they are worn out. |
| Error code: | E722 |
| Description: | Jam not reaching the original exit sensor (during scanning): The original which passed the read sensor does not reach the original exit sensor when it is transported from the scanning section to exit section. |
| Causes: | Original exit sensor RADF board Perform the 05-3210 Roller |
| Remedy: | 1. Clean the reading end roller and the exit intermediate roller if they are stained. 2. Is the original exit sensor working? (Perform the input check: 03-[FAX]ON/[7]/[E]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original exit sensor or the harnesses are open circuited. Correct if any. 4. Replace the original exit sensor 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Replace the reading end roller and the exit intermediate roller if they are worn out. |
| Error code: | E723 |
| Description: | Original not reaching small original reverse sensor (during scanning): An original which has passed the read sensor does not reach the small original reverse sensor when this original is transported from the scanning section to the reverse section. |
| Remedy: | Are the registration roller, read roller and small original reverse roller stained? ↓ YES → Clean the rollers. NO Are the small original exit flapper and small original reverse flapper operating normally? ↓ NO Adjust the small original exit solenoid. |
| Error code: | E724 |
| Description: | Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor. |
| Causes: | Original registration sensor RADF board Perform the 05-3210 Roller |
| Remedy: | 1. Clean the original registration roller if it is stained. 2. Is the original registration sensor working? (Perform the input check: 03-[FAX]ON/[7]/[H]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN74 on the RADF board is disconnected from the original registration sensor or the harnesses are open circuited. Correct if any. 4. Replace the original registration sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Replace the original registration roller if it is worn out. |
| Error code: | E725 |
| Description: | Stop jam at the reading start sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor. |
| Causes: | Original reading start sensor RADF board Perform the 05-3210 Roller Registration roller, Read roller |
| Remedy: | 1. Clean the original registration roller, intermediate transfer roller, reading start roller, reverse roller and reverse registration roller if they are stained. 2. Is the original reading start sensor working? (Perform the input check: 03-[FAX]ON/[7]/[G]) * If it is working properly, proceed to 8. If not, check 3 to 7 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original reading start sensor or the harnesses are open circuited. Correct if any. 4. Perform the automatic adjustment of the original reading start sensor (05-356). 5. Perform the manual adjustment of the original reading start sensor. 6. Replace the original reading sensor, and then perform the automatic adjustment of the original reading start sensor (05-356). 7. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 8. Replace the original registration roller, intermediate transfer roller, reading start roller, reverse roller and reverse registration roller if they are worn out. |
| Error code: | E726 |
| Description: | Transport/exit signal reception jam during ADF standby status |
| Remedy: | 1. Check if there is any paper in the RADF. Remove it if there is. 2. Check if there is any paper in the equipment. Remove it if there is. 3. If a jam still occurs, turn the power OFF and then back ON to check if the equipment operates normally. |
| Error code: | E728 |
| Description: | Original not reaching small original exit sensor (during scanning): An original which has passed the read sensor does not reach the small original exit sensor when this original is transported from the scanning section to the exit section. |
| Remedy: | Are the registration roller, read roller and small original reverse roller stained? ↓ YES → Clean the rollers. NO Are the small original exit flapper and small original reverse flapper operating normally? ↓ NO Adjust the small original exit solenoid. |
| Error code: | E731 |
| Description: | Stop jam at the original exit sensor: The trailing edge of the original does not pass the original exit sensor after its leading edge has reached this sensor |
| Causes: | Original exit sensor RADF board Perform the 05-3210 Roller Exit roller |
| Remedy: | 1. Clean the exit roller and the exit intermediate roller if they are stained. 2. Is the original exit sensor working? (Perform the input check: 03-[FAX]ON/[7]/[E]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original exit sensor or the harnesses are open circuited. Correct if any. 4. Replace the original exit sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Replace the exit roller and the exit intermediate roller if they are worn out. |
| Error code: | E732 |
| Description: | Original stopping at small original exit sensor: The trailing edge of the original does not pass the small original exit sensor after its leading edge has reached the small original exit sensor. |
| Remedy: | Are the registration roller, read roller and small original reverse roller stained? ↓ YES → Clean the rollers. NO Are the small original exit flapper and small original reverse flapper operating normally? ↓ NO Adjust the small original exit solenoid. |
| Error code: | E733 |
| Description: | Original not reaching large original exit sensor (exit section) |
| Causes: | An error in data communication occurs in the Engine controller. |
| Remedy: | Are the read roller and reverse roller stained? ↓ YES Clean the rollers. NO Is the reverse flapper working properly? ↓ YES NO Adjust the reverse solenoid. |
| Error code: | E741 |
| Description: | Original stopping at small original reverse sensor: The trailing edge of the original does not pass the small original reverse sensor after its leading edge has reached the small original reverse sensor. |
| Remedy: | Are the registration roller, read roller and small original reverse roller stained? ↓ YES → Clean the rollers. NO Are the small original exit flapper and small original reverse flapper operating normally? ↓ NO Adjust the small original exit solenoid. |
| Error code: | E742 |
| Description: | Original not reaching small original reverse sensor (during reverse feeding): The leading edge of the original does not reach the small original reverse sensor when this original is fed out of the reverse section. |
| Remedy: | Are the registration roller, read roller and small original reverse roller stained? ↓ YES → Clean the rollers. NO Are the small original exit flapper and small original reverse flapper operating normally? ↓ NO Adjust the small original exit solenoid. |
| Error code: | E743 |
| Description: | Original not reaching small original exit sensor (during reverse feeding): An original which has passed the small original reverse sensor does not reach the small original exit sensor when this original is exited out of the reverse section. |
| Remedy: | Are the registration roller, read roller and small original reverse roller stained? ↓ YES → Clean the rollers. NO Are the small original exit flapper and small original reverse flapper operating normally? ↓ NO Adjust the small original exit solenoid. |
| Error code: | E751 |
| Description: | Original stopping at original intermediate transport sensor: The trailing edge of the original does not pass the original intermediate transport sensor after its leading edge has reached the original intermediate transport sensor. |
| Remedy: | Are the registration roller, read roller and small original reverse roller stained? ↓ YES → Clean the rollers. NO Are the small original exit flapper and small original reverse flapper operating normally? ↓ NO Adjust the small original exit solenoid. |
| Error code: | E752 |
| Description: | Original not reaching original intermediate transport sensor: The leading edge of the original which has passed the read sensor does not reach the original intermediate transport sensor. |
| Remedy: | Are the registration roller, read roller and small original reverse roller stained? ↓ YES → Clean the rollers. NO Are the small original exit flapper and small original reverse flapper operating normally? ↓ NO Adjust the small original exit solenoid. |
| Error code: | E761 |
| Description: | Original remaining at original length detection sensor |
| Remedy: | Is the paper positioned on the sensor? ↓ YES → Remove the paper. NO Are the connector on the ADF board disconnected? (CN11,CN13,CN15,CN16) ↓ YES → Connect the connector. NO Are the sensors working? (Perform the input check in the test mode: 03-[FAX] OFF/[8]/[E], OFF/[7]/[H], OFF/[8]/[F], OFF/[8]/[G], OFF/[8]/[H], OFF/[7]/[G], OFF/[7]/[F], OFF/[8]/[D], OFF/[8]/[C], OFF/[7]/[E]) ↓ YES → Replace the ADF board. NO Are the connector of the sensors disconnected? ↓ YES → Connect the connector. NO In case of [E761],[E764],[E766],[E768], perform the automatic adjustment of RADF sensor. In case of [E762],[E763],[E765],[E767], replace the sensor. |
| Error code: | E762 |
| Description: | Original registration sensor paper remaining jam |
| Causes: | Original exit reverse sensor Registration sensor Original width detection sensor-1 Original width detection sensor-2 Original width detection sensor-3 Intermediate transport sensor Reading end sensor Exit sensor RADF board Perform the 05-3210 Roller |
| Remedy: | 1. Check if there is any paper on each sensor. Remove it if there is. 2. Is each sensor working? (Perform input check: 03) [E746]: [FAX]/ON/[5]/[B], [E762]: [FAX]/ON/[7]/[H], [E770]: [FAX]/ON/[8]/[F], [E771]: [FAX]/ON/[8]/[G], [E772]: [FAX]/ON/[8]/[H], [E773]: [FAX]/ON/[7]/[F], [E774]: [FAX]/ON/[7]/[G], [E775]: [FAX]/ON/[5]/[D], [E777]: [FAX]/ON/[7]/[E] 3. Check if the connector CN74 or CN75 on the RADF board is disconnected from each sensor or the harnesses are open-circuited. Correct if this is the case. 4. Replace each sensor. * If the original reading start sensor is replaced, perform automatic adjustment (05-356) for it. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). |
| Error code: | E763 |
| Description: | Original remaining at original width detection sensor |
| Remedy: | Is the paper positioned on the sensor? ↓ YES → Remove the paper. NO Are the connector on the ADF board disconnected? (CN11,CN13,CN15,CN16) ↓ YES → Connect the connector. NO Are the sensors working? (Perform the input check in the test mode: 03-[FAX] OFF/[8]/[E], OFF/[7]/[H], OFF/[8]/[F], OFF/[8]/[G], OFF/[8]/[H], OFF/[7]/[G], OFF/[7]/[F], OFF/[8]/[D], OFF/[8]/[C], OFF/[7]/[E]) ↓ YES → Replace the ADF board. NO Are the connector of the sensors disconnected? ↓ YES → Connect the connector. NO In case of [E761],[E764],[E766],[E768], perform the automatic adjustment of RADF sensor. In case of [E762],[E763],[E765],[E767], replace the sensor. |
| Error code: | E764 |
| Description: | Original remaining at read sensor |
| Remedy: | Is the paper positioned on the sensor? ↓ YES → Remove the paper. NO Are the connector on the ADF board disconnected? (CN11,CN13,CN15,CN16) ↓ YES → Connect the connector. NO Are the sensors working? (Perform the input check in the test mode: 03-[FAX] OFF/[8]/[E], OFF/[7]/[H], OFF/[8]/[F], OFF/[8]/[G], OFF/[8]/[H], OFF/[7]/[G], OFF/[7]/[F], OFF/[8]/[D], OFF/[8]/[C], OFF/[7]/[E]) ↓ YES → Replace the ADF board. NO Are the connector of the sensors disconnected? ↓ YES → Connect the connector. NO In case of [E761],[E764],[E766],[E768], perform the automatic adjustment of RADF sensor. In case of [E762],[E763],[E765],[E767], replace the sensor. |
| Error code: | E765 |
| Description: | Original remaining at original intermediate transport sensor |
| Remedy: | Is the paper positioned on the sensor? ↓ YES → Remove the paper. NO Are the connector on the ADF board disconnected? (CN11,CN13,CN15,CN16) ↓ YES → Connect the connector. NO Are the sensors working? (Perform the input check in the test mode: 03-[FAX] OFF/[8]/[E], OFF/[7]/[H], OFF/[8]/[F], OFF/[8]/[G], OFF/[8]/[H], OFF/[7]/[G], OFF/[7]/[F], OFF/[8]/[D], OFF/[8]/[C], OFF/[7]/[E]) ↓ YES → Replace the ADF board. NO Are the connector of the sensors disconnected? ↓ YES → Connect the connector. NO In case of [E761],[E764],[E766],[E768], perform the automatic adjustment of RADF sensor. In case of [E762],[E763],[E765],[E767], replace the sensor. |
| Error code: | E766 |
| Description: | Original remaining at small original reverse sensor |
| Causes: | Error in connection occurred due to main controller software *: xxxxTask number related to Exception is shown in decimal |
| Remedy: | Is the paper positioned on the sensor? ↓ YES → Remove the paper. NO Are the connector on the ADF board disconnected? (CN11,CN13,CN15,CN16) ↓ YES → Connect the connector. NO Are the sensors working? (Perform the input check in the test mode: 03-[FAX] OFF/[8]/[E], OFF/[7]/[H], OFF/[8]/[F], OFF/[8]/[G], OFF/[8]/[H], OFF/[7]/[G], OFF/[7]/[F], OFF/[8]/[D], OFF/[8]/[C], OFF/[7]/[E]) ↓ YES → Replace the ADF board. NO Are the connector of the sensors disconnected? ↓ YES → Connect the connector. NO In case of [E761],[E764],[E766],[E768], perform the automatic adjustment of RADF sensor. In case of [E762],[E763],[E765],[E767], replace the sensor. |
| Error code: | E767 |
| Description: | Original remaining at small original exit sensor |
| Remedy: | Is the paper positioned on the sensor? ↓ YES → Remove the paper. NO Are the connector on the ADF board disconnected? (CN11,CN13,CN15,CN16) ↓ YES → Connect the connector. NO Are the sensors working? (Perform the input check in the test mode: 03-[FAX] OFF/[8]/[E], OFF/[7]/[H], OFF/[8]/[F], OFF/[8]/[G], OFF/[8]/[H], OFF/[7]/[G], OFF/[7]/[F], OFF/[8]/[D], OFF/[8]/[C], OFF/[7]/[E]) ↓ YES → Replace the ADF board. NO Are the connector of the sensors disconnected? ↓ YES → Connect the connector. NO In case of [E761],[E764],[E766],[E768], perform the automatic adjustment of RADF sensor. In case of [E762],[E763],[E765],[E767], replace the sensor. |
| Error code: | E768 |
| Description: | Original remaining at large original exit sensor |
| Remedy: | Is the paper positioned on the sensor? ↓ YES → Remove the paper. NO Are the connector on the ADF board disconnected? (CN11,CN13,CN15,CN16) ↓ YES → Connect the connector. NO Are the sensors working? (Perform the input check in the test mode: 03-[FAX] OFF/[8]/[E], OFF/[7]/[H], OFF/[8]/[F], OFF/[8]/[G], OFF/[8]/[H], OFF/[7]/[G], OFF/[7]/[F], OFF/[8]/[D], OFF/[8]/[C], OFF/[7]/[E]) ↓ YES → Replace the ADF board. NO Are the connector of the sensors disconnected? ↓ YES → Connect the connector. NO In case of [E761],[E764],[E766],[E768], perform the automatic adjustment of RADF sensor. In case of [E762],[E763],[E765],[E767], replace the sensor. |
| Error code: | E800 |
| Description: | 24 VDC supply off jam: A job is started or continued while 24 VDC supply is shut off. |
| Remedy: | Are the main unit and RADF working normally? ↓ NO → Connect the connector. YES If the RADF opening / closing switch open circuited? ↓ YES Adjust the RADF opening switch. |
| Error code: | E860 |
| Description: | Original jam access cover open: The Original jam access cover has opened during RADF operation. |
| Causes: | Original exit reverse sensor RADF board Perform the 05-3210 |
| Remedy: | 1. Close the original jam access cover or the original reverse unit if they are opened. Remove if there are any original before closing them. 2. Is the original jam access cover opening/closing sensor and the original revese unit opening/ closing sensor working? (Perform the input check: 03) Original jam access cover opening/closing sensor: 03-[FAX]ON/[7]/[C], Original revese unit opening/closing sensor: 03-[FAX]ON/[5]/[C] * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN74 or CN75 on the RADF board is disconnected from the original jam access cover opening/closing sensor, original revese unit opening/closing sensor or the harnesses are open circuited. Correct if any. 4. Replace the original jam access cover opening/closing sensor or the original revese unit opening/closing sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). |
| Error code: | E870 |
| Description: | RADF open jam: RADF has opened during RADF operation. |
| Causes: | RADF opening/closing sensor RADF board Perform the 05-3210 |
| Remedy: | 1. Close the RADF if it is opened. Remove if there is any original before closing it. 2. Is the RADF opening/closing sensor working? (Perform the input check: 03-[FAX]ON/[7]/[D]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN75 on the RADF board is disconnected from the RADF opening/ closing sensor or the harnesses are open circuited. Correct if any. 4. Replace the RADF opening/closing sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Is the RADF opening/closing sensor adjusted within the specified range? |
| Error code: | E9F0 |
| Description: | Hole punch jam: Hole punching is not performed properly. |
| Causes: | Punch HP sensor (S4) Punch motor (M3) Punch controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or equipment? → YES → Remove the paper. NO Is the connector J1 on the punch driver PC board disconnected? Is the harness connecting the punch driver PC board and punch home position sensor (PI3P) open circuited? → YES → Connect the connector securely. Replace the harness. NO Is the punch home position sensor working properly? l → NO → 1. Connect the connector of the punch home position sensor securely. 2. Replace the punch home position sensor. YES Replace the punch driver PC board. |
| Error code: | EA10 |
| Description: | Paper transport delay jam: Paper which has passed the exit sensor does not reach the inlet sensor. |
| Causes: | Feeding sensor (S22) Transport path switching solenoid (SOL5) Entrance motor (M1) Interface PC board (I/F) Finisher control PC board (FIN) |
| Remedy: | Is there any paper remaining on the transport path in the finisher or equipment? → YES → Remove the paper. NO Is the connector J17 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) open circuited? → YES → Connect the connector securely. Replace the harness. NO Is the inlet sensor working normally? (Check the movement of the actuator.) ll → NO → 1. Connect the connector of the inlet sensor securely. 2. Attach the actuator securely if its shaft is out of place. 3. Replace the inlet sensor. YES Replace the finisher controller PC board. |
| Error code: | EA20 |
| Description: | Paper transport stop jam: Paper which has reached the inlet sensor does not pass the inlet sensor. |
| Causes: | Entrance sensor (S1) Finisher control PC board (FIN) |
| Remedy: | Is there any paper remaining on the transport path in the finisher or main unit? → YES → Remove the paper. NO Is any of the connectors J17, J24, J9 and J11 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) opencircuited? Is the harness connecting the finisher controller PC board and buffer path inlet paper sensor (PI17) open-circuited? Is the harness connecting the finisher controller PC board and buffer path paper sensor (PI14) open circuited? Is the harness connecting the finisher controller PC board and stapling tray sensor (PI4) open circuited? Is the harness connecting the finisher controller PC board and delivery sensor (PI3) open circuited? → YES → Connect the connectors securely. Replace the harnesses. NO Is the inlet sensor working properly? (Check the movement of the actuator.) Is the buffer path inlet paper sensor working properly? (Check the movement of the actuator.) Is the buffer path paper sensor working properly? (Check the movement of the actuator.) Is the stapling tray sensor working properly? (Check the movement of the actuator.) Is the delivery sensor working properly? (Check the movement of the actuator.) ll → NO → 1. Connect the connectors of the sensors securely. 2. Attach the actuators securely if their shafts are out of place. 3. Replace the sensors. YES Replace the finisher controller PC board. |
| Error code: | EA30 |
| Description: | Power-ON jam: Paper is remaining at the inlet sensor when the power is turned ON. |
| Causes: | Entrance sensor Finisher controller PC board |
| Remedy: | Is there any paper remaining on the transport path in the finisher? → YES → Remove the paper. NO Is any of the connectors J17, J24 and J11 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) opencircuited? Is the harness connecting the finisher controller PC board and buffer path inlet paper sensor(PI17) open-circuited? Is the harness connecting the finisher controller PC board and buffer path paper sensor (PI14) open circuited? Is the harness connecting the finisher controller PC board and delivery sensor (PI3) open circuited? → YES → Connect the connectors securely. Replace the harnesses. NO Is the inlet sensor working properly? (Check the movement of the actuator.) Is the buffer path inlet paper sensor working properly? (Check the movement of the actuator.) Is the buffer path paper sensor working properly? (Check the movement of the actuator.) Is the delivery sensor working properly? (Check the movement of the actuator.) ll → NO → 1. Connect the connectors of the sensors securely. 2. Attach the actuators securely if their shafts are out of place. 3. Replace the sensors. YES Replace the finisher controller PC board. |
| Error code: | EA40 |
| Description: | Door open jam: The upper cover or the front cover of the Finisher has opened, or the upper door or the front door of the Hole Punch Unit has opened during printing. |
| Causes: | Front cover switch (SW1) Stationary tray opening/closing switch (SW2) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or main unit? → YES → Remove the paper. NO Is the finisher connected with the main unit? → NO → Connect the finisher with the main unit. YES Is the connector J12 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and joint sensor (PI15) opencircuited? → YES → Connect the connector securely. Replace the harness. NO Is the joint sensor working properly? l → NO → 1. Connect the connector of the joint sensor securely. 2. Replace the joint sensor. YES Is the door of the finisher closed? → NO → Close the door. YES Is the connector J12 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and door opening sensor (PI16) open-circuited? → YES → Connect the connector securely. Replace the harness. NO Is the door opening sensor working properly? l → NO → 1. Connect the connector of the door opening sensor securely. 2. Replace the door opening sensor. YES Is the connector J5 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and door switch (MS1) opencircuited? → YES → Connect the connector securely. Replace the harness. NO Is the connector J5 on the punch driver PC board disconnected? Is the harness connecting the punch driver PC board and front door switch (MS2P) opencircuited? → YES → Connect the connector securely. Replace the harness. NO Are the upper and front door switches working properly? ll → NO → 1. Connect the connectors of the door switch and the front door switch securely. 2. Replace the upper/front door switches. YES Replace the finisher controller PC board. |
| Error code: | EA50 |
| Description: | Stapling jam: Stapling is not performed properly |
| Causes: | Stapler interference sensor (S11) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or equipment or on the stapling tray? → YES → Remove the paper. NO Is the jam cleared by taking off the staple cartridge from the finisher and removing the staple sheet slid from the staple case? → YES → End. NO Is the connector J8 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and stapling home position sensor (PI22) open circuited? → YES → Connect the connector securely. Replace the harness. NO Is the stapling home position sensor working properly? l → NO → 1. Connect the connector of the stapling home position sensor securely. 2. Replace the stapling home position sensor. YES Replace the finisher controller PC board. |
| Error code: | EA60 |
| Description: | Early arrival jam: The inlet sensor detects paper earlier than the specified timing |
| Causes: | Entrance sensor (S1) Finisher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or equipment? → YES → Remove the paper. NO Is the connector J17 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) open circuited? → YES → Connect the connector securely. Replace the harness. NO Is the inlet sensor working properly? (Check the movement of the actuator.) ll → NO → 1. Connect the connector of the inlet sensor securely. 2. Attach the actuator securely if its shaft is out of place. 3. Replace the inlet sensor. YES Replace the finisher controller PC board. |
| Error code: | EA80 |
| Description: | Stapling jam: Stapling is not performed properly. |
| Causes: | Stitcher home position switch Finisher controller PC board |
| Remedy: | Is there any paper remaining on the transport path in the finisher, saddle stitcher section or main unit, or on the stapling tray? → YES → Remove the paper. NO Is the jam cleared by taking off the staple cartridge from the finisher and removing the staples stuck in the stapling unit? → YES → End NO Is the connector J8 on the saddle stitcher controller PC board disconnected? Is the harness connecting the saddle stitcher controller PC board and stitcher home position switch (rear: MS5S, front: MS7S) open-circuited? → YES → Connect the connector securely. Replace the harness. NO Are the stitcher home position switches working properly? ll → NO → 1. Connect the connectors of the stitcher home position switches securely. 2. Replace the stitcher home position switches. YES Replace the saddle stitcher controller PC board. |
| Error code: | EA90 |
| Description: | Door open jam: The delivery cover or the inlet cover has opened during printing. |
| Causes: | Delivery cover sensor (PI3) Inlet cover sensor (PI9) Saddle stitcher controller board |
| Remedy: | main unit? → YES → Remove the paper. NO Is the saddle stitcher door closed? → NO → Close the door. YES Is either of the connectors J10 or J11 on saddle stitcher controller PC board disconnected? Are the harnesses connecting the saddle stitcher controller PC board and cover opening sensors (PI2S: front door opening/closing sensor, PI3S:delivery cover sensor, PI9S: inlet cover sensor) open-circuited? → YES → Connect the connector securely. Replace the harness. NO Are the cover opening sensors working properly? l → NO → 1. Connect the connectors of the cover opening sensors securely. 2. Replace the cover opening sensors. YES Replace the finisher controller PC board. |
| Error code: | EAA0 |
| Description: | Power-ON jam: Paper is remaining at the No. 1 paper sensor, No. 2 paper sensor, No. 3 paper sensor, vertical path paper sensor or delivery sensor when the power is turned ON. |
| Causes: | No. 1 paper sensor (PI18) No. 2 paper sensor (PI19) No. 3 paper sensor (PI20) Vertical path paper sensor (PI17) Delivery sensor (PI11) Saddle stitcher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher or saddle stitcher section? → YES → Remove the paper. NO Is any of the connectors J10, J13 and J9 on the saddle stitcher controller PC board disconnected? Is the harness connecting the saddle stitcher controller PC board and No.1 paper sensor (PI18S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and No.2 paper sensor (PI19S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and No.3 paper sensor (PI20S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and vertical path paper sensor (PI17S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and delivery sensor (PI11S) open-circuited? → YES → Connect the connectors securely. Replace the harnesses. NO Is the No.1 paper sensor working properly? (Check the movement of the actuator.) Is the No.2 paper sensor working properly? (Check the movement of the actuator.) Is the No.3 paper sensor working properly? (Check the movement of the actuator.) Is the vertical path paper sensor working properly? (Check the movement of the actuator.) Is the delivery sensor working properly? (Check the movement of the actuator.) ll → NO → 1. Connect the connectors of the sensors securely. 2. Attach the actuators securely if their shafts are out of place. 3. Replace the sensors. YES Replace the saddle stitcher controller PC board. |
| Error code: | EAB0 |
| Description: | Paper transport stop jam: Paper which has passed the inlet sensor does not reach or pass the No. 1 paper sensor, No. 2 paper sensor, No. 3 paper sensor or delivery sensor. |
| Causes: | No. 1 paper sensor (PI18) No. 2 paper sensor (PI19) No. 3 paper sensor (PI20) Delivery sensor (PI11) Saddle stitcher controller board |
| Remedy: | Is there any paper remaining on the transport path in the finisher, saddle stitcher section or main unit? → YES → Remove the paper. NO Is the connector J17 on finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) opencircuited? Is either of the connectors J10 or J9 on the saddle stitcher controller PC board disconnected? Is the harness connecting the saddle stitcher controller PC board and No.1 paper sensor (PI18S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and No.2 paper sensor (PI19S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and No.3 paper sensor (PI20S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and delivery sensor (PI11S) open-circuited? → YES → Connect the connectors securely. Replace the harnesses. NO Is the inlet sensor working properly? (Check the movement of the actuator.) Is the No.1 paper sensor working properly? (Check the movement of the actuator.) Is the No.2 paper sensor working properly? (Check the movement of the actuator.) Is the No.3 paper sensor working properly? (Check the movement of the actuator.) Is the delivery sensor working properly? (Check the movement of the actuator.) ll → NO → 1. Connect the connectors of the sensors securely. 2. Attach the actuators securely if their shafts are out of place. 3. Replace the sensors. YES Replace the saddle stitcher controller PC board. |
| Error code: | EAC0 |
| Description: | Transport delay jam: Paper which has reached the inlet sensor does not pass the inlet sensor. |
| Remedy: | Is there any paper remaining on the transport path in the finisher, saddle stitcher section or main unit? → YES → Remove the paper. NO Is the connector J17 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) opencircuited? → YES → Connect the connector securely. Replace the harness. NO Is the inlet sensor working properly? (Check the movement of the actuator.) ll → NO → 1. Connect the connector of the sensor securely. 2. Attach the actuator securely if its shaft is out of place. 3. Replace the sensor. YES Replace the finisher controller PC board. |
| Error code: | EAD0 |
| Description: | Print end command time-out jam: The printing has not finished normally due to the communication error between the SYS board and LGC board at the end of the printing. |
| Causes: | SYS board LGC board |
| Remedy: | Is the main motor rotating normally? → NO 1. Check if there is any paper in the equipment. Remove it if there is. 2. If the error still occurs, check the following: 3. Check if the error is cleared by turning the power OFF and then back ON. 4. Check if the connectors connecting the SYS board, SYSIF board, SLG board and PLG board are disconnected. 5. Check if the harnesses connecting the SYS board, SLG board and PLG board are open circuited. 6. Replace the SYS board, SYSIF board and LGC board. |
| Error code: | EAE0 |
| Description: | Receiving period time-out jam: The printing cannot be finished normally due to the communication error between the equipment and the Finisher when the paper is transported from the equipment to the Finisher. |
| Causes: | Finisher controller board |
| Remedy: | Is the finisher working? → YES → Replace the finisher controller PC board. NO 1. Check if the voltage (24V) is being supplied to the finisher. 2. Check the connection of the LGC board and IPC board. 3. Check if the harness connecting the IPC board and finisher I/F connector of the equipment side is open circuited. 4. Check if the harness connecting the I/F connector of the finisher side and finisher controller PC board is open circuited. 5. Replace the finisher controller PC board. |
| Error code: | EB30 |
| Description: | Ready period time-out jam: The equipment judges that the paper transport to the Finisher is disabled due to the communication error between the equipment and the Finisher at the start of the printing. |
| Causes: | Finisher controller board LGC board |
| Remedy: | Is there paper in the equipment? → NO → Replace the LGC board. YES Are the IPC board and LGC board properly connected to each other? → NO → Connect them properly. YES Is the harness securely connected to the IPC board? → NO → Connect the harness properly. YES Is any of the connector pins of the harness connecting the equipment and finisher disconnected or any of those harnesses open circuited? → NO → Connect the pin or replace the harness. YES 1. Replace the IPC board. 2. Replace the LGC board. 3. Replace the finisher controller PC board. |
| Error code: | EB50 |
| Description: | Paper remaining on the transport path: The multiple feeding of the preceding paper caused the misfeeding of the upcoming paper. |
| Causes: | 1st drawer feed sensor Bypass feed sensor ADU exit sensor Registration sensor 1st drawer feed sensor 2nd drawer feed sensor ADU board LGC board Rollers |
| Remedy: | In case the paper is fed from the 1st drawer, bypass unit or Open the bypass unit cover. Is there any paper in front of the drawer feed sensor? ll → YES → Remove the paper. * Clean or replace the feed roller and separation roller if this error occurs frequently. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[FAX]ON/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Check the rollers. Clean or replace them. In case the paper is fed from the 2nd drawer, 3rd drawer, 4th drawer, Tandem LCF Open the bypass unit cover. Is there any paper in front of the 1st drawer transport sensor? ll → YES → Remove the paper. * Clean or replace the feed roller and separation roller if this error occurs frequently. NO Are the 1st drawer transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/[C]) ↓ → NO → 1. Check if the connector of the 1st drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 1st drawer transport sensor. 6. Replace the LGC board. YES If any paper remains in the equipment or drawer, remove it. Check the rollers. Clean or replace them. |
| Error code: | EB60 |
| Description: | Paper remaining on the transport path: The multiple feeding of the preceding paper caused the misfeeding of the upcoming paper (= redetection after no jam is detected at [EB50]). |
| Causes: | Registration sensor PFC board Rollers |
| Remedy: | Open the bypass unit cover. Is there any paper in front of the registration sensor? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[4]/[E]) ↓ → NO → 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Check the rollers. Clean or replace them. |
| Error code: | EC00 |
| Display: | Unusable Device Remove the Device. Turn the power off and back on again. |
| Description: | Inserter feeding delay jam |
| Causes: | 1 USB host PCB failure 2 Main PCB failure |
| Remedy: | Are the pickup roller, feed roller and separation roller tainted? → YES → Clean up the rollers. NO Is the harness between the inserter control board and separation sensor open-circuited? → YES → Replace the harness. NO Is the separation sensor working improperly? → YES → Replace the separation sensor. NO Replace the inserter control board. |
| Error code: | EC10 |
| Description: | Inserter feeding stop jam |
| Remedy: | Are the transport roller and reverse roller tainted? → YES → Clean up the rollers. NO Is the harness between the inserter control board and separation sensor open-circuited? → YES → Replace the harness. NO Is the separation sensor working improperly? → YES → Replace the separation sensor. NO Replace the inserter control board. |
| Error code: | EC20 |
| Description: | Inserter reverse path delay jam-1 |
| Remedy: | Are the transport roller and reverse roller tainted? → YES → Clean up the rollers. NO Is the harness between the inserter control board and reverse path sensor is opencircuited? → YES → Replace the harness. NO Is the reverse path sensor working improperly? → YES → Replace the reverse path sensor. NO Replace the inserter control board. |
| Error code: | EC30 |
| Description: | Inserter reverse path stop jam-1 |
| Remedy: | Are the transport roller and reverse roller tainted? → YES → Clean up the rollers. NO Is the harness between the inserter control board and reverse path sensor is opencircuited? → YES → Replace the harness. NO Is the reverse path sensor working improperly? → YES → Replace the reverse path sensor. NO Replace the inserter control board. |
| Error code: | EC40 |
| Description: | Inserter reverse path delay jam-2 |
| Remedy: | Are the transport roller and reverse roller tainted? → YES → Clean up the rollers. NO Is the harness between the inserter control board and reverse path sensor is opencircuited? → YES → Replace the harness. NO Is the reverse path sensor working improperly? → YES → Replace the reverse path sensor. NO Replace the inserter control board. |
| Error code: | EC50 |
| Description: | Inserter reverse path stop jam-2 |
| Remedy: | Are the transport roller and reverse roller tainted? → YES → Clean up the rollers. NO Is the harness between the inserter control board and reverse path sensor is opencircuited? → YES → Replace the harness. NO Is the reverse path sensor working improperly? → YES → Replace the reverse path sensor. NO Replace the inserter control board. |
| Error code: | EC60 |
| Description: | Inserter transport delay jam-1 |
| Remedy: | Is the transport roller tainted? → YES → Clean up the roller. NO Is the harness between the inserter control board and transport sensor is open-circuited? → YES → Replace the harness. NO Is the transport sensor working impropely? → YES → Replace the transport sensor. NO Replace the inserter control board. |
| Error code: | EC70 |
| Description: | Inserter transport stop jam-1 |
| Remedy: | Is the transport roller tainted? → YES → Clean up the roller. NO Is the harness between the inserter control board and transport sensor is open-circuited? → YES → Replace the harness. NO Is the transport sensor working impropely? → YES → Replace the transport sensor. NO Replace the inserter control board. |
| Error code: | EC80 |
| Description: | Inserter transport delay jam-2 |
| Remedy: | Is the transport roller tainted? → YES → Clean up the roller. NO Is the harness between the inserter control board and transport sensor is open-circuited? → YES → Replace the harness. NO Is the transport sensor working impropely? → YES → Replace the transport sensor. NO Replace the inserter control board. |
| Error code: | EC90 |
| Description: | Inserter transport stop jam-2 |
| Remedy: | Is the transport roller tainted? → YES → Clean up the roller. NO Is the harness between the inserter control board and transport sensor is open-circuited? → YES → Replace the harness. NO Is the transport sensor working impropely? → YES → Replace the transport sensor. NO Replace the inserter control board. |
| Error code: | ECA0 |
| Description: | Paper remaining in Inserter Unit at power-ON |
| Remedy: | Is there any paper remaining at the inserter transport path? → YES → Remove the paper. NO Are the separation sensor, reverse path sensor and transport sensor working improperly? → YES → Replace the sensors. NO Replace the inserter control board. |
| Error code: | ECB0 |
| Description: | Incorrect setting of paper size for Inserter Unit |
| Remedy: | Is the paper size on the inserter tray consist with the size set at the copier control panel? → NO → Set the same paper size as that on the tray. YES Is the separation sensor working improperly? → YES → Replace the separation sensor. NO Perform the width adjustment of the inserter tray side guide. |
| Error code: | ECC0 |
| Description: | Inserter Unit misfeeding |
| Remedy: | Is the condition improved when the copier power switch is turned OFF/ON? → NO 1. Replace the copier LGC board. 2. Replace the IPC board. 3. Replace the inserter control board |
| Error code: | ECD0 |
| Description: | Inserter Unit door open jam |
| Remedy: | Is the problem solved by opening the inserter jam access cover? → NO 1. Check the installation state of the cover. 2. Replace the cover switch and plate spring. |
| Error code: | F070 |
| Description: | Communication error between System-CPU and Engine-CPU |
| Causes: | Switching regulator • Replace the fuse (F210). • Replace the switching regulator. LGC board SYS board If the problem is not corrected with the replacement of the LGC board, reinstall the removed LGC board and replace the SYS board. IMG board If the problem is still not corrected with the replacement of the SYS board, reinstall the removed SYS board and replace the IMG board. |
| Remedy: | (1) Check if the connector CN104 on the SYS board and CN130, CN131, CN134 on the SYSIF board is disconnected. (2) Check if the connector CN10 on the SLG board is disconnected. (3) Check if the harness connecting the SYSIF board and SLG board is disconnected or open circuited. (4) Check if the harness connecting the SYSIF board and LGC board is disconnected or open circuited. (5) Check if the connection of the SYS board (CN104) and SYSIF board (CN130) is open circuited. (6) If the SYS board has been replaced, check if the jumper pin setting on the SYS board is correct. (The jumper pin should be inserted between pin 2 and 3 of CN103 and CN115.) (7) Check the version of the system ROM on the SYS board. (8) Check the version of the engine ROM version on the LGC board. (9) Check the version of the scanner ROM version on the SLG board. (10) Replace the SYS board. (11) Replace the SLG board. (12) Replace the LGC board. (13) Replace the SYSIF board. |
| Error code: | F090 |
| Description: | SRAM abnormality on SYS board |
| Causes: | SRAM (SYS board) |
| Remedy: | (1) Turn the power OFF and start up the Setting Mode (08). (2) When “SRAM ERROR DOES IT INITIALIZE” is displayed on the LCD, check the destination and then press the [START] button. If the destination is not correct, key in the correct one and then press the [START] button. (3) After the confirmation message is displayed on the LCD, press the [INTERRUPT] button (to initialize the SRAM). (4) Perform the panel calibration (08-692). (5) Perform the initialization at the software version upgrade (08-947). (6) Enter the serial number (08-995). Be sure that the serial number is the same as that on the identification label attached on the rear cover of the equipment. Note: The MAC address of the equipment is generated based on this serial number. Entering the incorrect serial number may result in an inability to access the network due to an invalid MAC address. (7) Initialize the NIC information (08-693). (8) Turn the power OFF and then start up with the Adjustment mode (05). (9) Turn the power OFF and then back ON. If the error is not recovered, replace the SRAM on the SYS board. |
| Error code: | F091 |
| Description: | FRAM abnormality on SYS board |
| Remedy: | (1) Turn the power OFF and start up the Setting Mode (08). (2) When the message “FRAM ERROR DOES IT INITIALIZE?” is displayed on the LCD, press [INITIALIZE]. (FRAM is initialized.) Note: When the FRAM is initialized, the scanner and image processing related adjustments are also initialized. Readjust them after the FRAM initialization. (3) Turn the power OFF and then back ON. If the error is not recovered, replace the FRAM on the SYS board. |
| Error code: | F092 |
| Description: | SRAM and FRAM abnormality on SYS board |
| Remedy: | (1) Turn the power OFF and start up the Setting Mode (08). (2) When the message “FRAM/SRAM ERROR DOES IT INITIALIZE?” is displayed on the LCD, press [INITIALIZE]. (SRAM is cleared and FRAM is initialized.) Note: When the FRAM is initialized, the scanner and image processing related adjustments are also initialized. Readjust them after the FRAM initialization. (3) Turn the power OFF and then back ON. If the error is not recovered, replace the FRAM on the SYS board. |
| Error code: | F100 |
| Description: | HDD format error: The HDD cannot be formatted normally. |
| Remedy: | (1) Check if the HDD is mounted. (2) Check if the specified HDD is mounted. (3) Check if the connector pins of the HDD are bent. (4) Check if the power supply connector is disconnected. (5) Check if the connector CN109 and CN114 on the SYS board is disconnected. (6) Replace the harness. (7) Initialize the HDD. (Key in “2” at 08-690.) (8) Replace the HDD. (9) Replace the SYS board. |
| Error code: | F101 |
| Description: | HDD unmounted: Connection of the HDD is not detected. |
| Causes: | HDD SYS board |
| Remedy: | (1) Check if the connectors of the HDD are disconnected. (2) Check if the connector pins are disconnected or the wires of harnesses are broken. (3) Perform the bad sector check (08-694). If the check result is OK, recover the data in the HDD. If the check result is failed, replace the HDD. (4) Replace the SYS board. |
| Error code: | F102 |
| Description: | HDD boot error: HDD does not become ready for booting. |
| Causes: | HDD SYS board |
| Remedy: | (1) Check if the connectors of the HDD are disconnected. (2) Check if the connector pins are disconnected or the wires of harnesses are broken. (3) Perform the bad sector check (08-694). If the check result is OK, recover the data in the HDD. If the check result is failed, replace the HDD. (4) Replace the SYS board. |
| Error code: | F103 |
| Description: | Finisher Paddle Failure An error was detected in the Finisher Paddle Motor. |
| Causes: | • Finisher Paddle Motor • Finisher Control Board |
| Remedy: | 1 Test these sensors. • Swing Guide Home Position Sensor • Paddle Home Position Sensor Run the appropriate Service Diagnostics sensor test. Do the sensors operate? Go to Step 2. Replace the sensor. If the error persists, go to Step 2. 2 Test the Paddle Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Paddle Motor test. Does the motor operate? Replace the Finisher Control Board. If the error persists, go to Step 4. Go to Step 4. 3 Check for +24 V to the Paddle Motor. Disconnect CN57. Is there +24 V across CN57-1 and -2 <=> ground? Replace the Delivery Motor. Replace the harness. If the error persists, go to Step 5. 4 Check all pins of the Inverter Interface Cable for continuity. Disconnect CN1 and CN2 from the Finisher Control Board and the opposite end from the Inverter. Is the cable conductive? Replace the Inverter Power Supply. Replace the cable. |
| Error code: | F104 |
| Description: | HDD data error: Abnormality is detected in the data of the HDD. |
| Causes: | HDD SYS board |
| Remedy: | (1) Check if the connectors of the HDD are disconnected. (2) Check if the connector pins are disconnected or the wires of harnesses are broken. (3) Perform the bad sector check (08-694). If the check result is OK, recover the data in the HDD. If the check result is failed, replace the HDD. (4) Replace the SYS board. |
| Error code: | F105 |
| Description: | Other HDD errors |
| Causes: | HDD SYS board |
| Remedy: | (1) Check if the connectors of the HDD are disconnected. (2) Check if the connector pins are disconnected or the wires of harnesses are broken. (3) Perform the bad sector check (08-694). If the check result is OK, recover the data in the HDD. If the check result is failed, replace the HDD. (4) Replace the SYS board. |
| Error code: | F106 |
| Description: | Finisher Stapler Swing Motor Failure The Stapler Swing Home Position Sensor detected a Stapler Swing Motor error. |
| Causes: | • Stapler Swing Motor • Finisher Control Board |
| Remedy: | 1 Test the Stapler Swing Home Position Sensor Run the Service Diagnostics Stapler Slide Home Position Sensor test. Do the sensors operate? Go to Step 2. Replace the sensor. If the error persists, go to Step 2. 2 Test the Swing Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Sliding Motor test. Does the motor operate? Replace the Finisher Control Board. If the error persists, go to Step 4. Go to Step 4. 3 Check for +24 V to the Swing Motor. Disconnect CN72. Is there +24 V across CN72-8 and -9 <=> ground? Replace the Slide Motor. Replace the harness. If the error persists, go to Step 5. 4 Check all pins of the Inverter Interface Cable for continuity. Disconnect CN1 and CN2 from the Finisher Control Board and the opposite end from the Inverter. Is the cable conductive? Replace the Inverter Power Supply. Replace the cable. |
| Error code: | F107 |
| Description: | /BOX partition damage |
| Remedy: | Initialize the Electronic Filing using the Setting Mode (08-666). |
| Error code: | F108 |
| Description: | /SHA partition damage |
| Remedy: | Initialize the shared folder using the Setting Mode (08-667). |
| Error code: | F110 |
| Description: | Finisher Staple Motor Failure An error was detected in the Staple Motor. |
| Causes: | • Finisher Staple Motor • Finisher Control Board |
| Remedy: | 1 Test these sensors. • Staple Clock Sensor • Fold Home Position Sensor Run the appropriate Service Diagnostics sensor test. Do the sensors operate? Go to Step 2. Replace the sensor. If the error persists, go to Step 2. 2 Test the Staple Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Staple Motor tests. Does the motor operate? Replace the Finisher Control Board. If the error persists, go to Step 4. Go to Step 3. 3 Check for +24 V to the Staple Motor. Disconnect CN71. Is there +24 V across CN71-1 and -2 <=> ground? Replace the Staple Motor. Replace the harness. If the error persists, go to Step 4. 4 Check all pins of the Inverter Interface Cable for continuity. Disconnect CN1 and CN2 from the Finisher Control Board and the opposite end from the Inverter. Is the cable conductive? Replace the Inverter Power Supply. Replace the cable. |
| Error code: | F111 |
| Description: | Finisher Stack Handling Motor Failure The Delivery Belt Home Position Sensor detected a Stack Handling error. |
| Causes: | • Finisher Stack Handling Motor • Finisher Control Board |
| Remedy: | 1 Check the delivery mechanism. Does the Delivery Belt turn freely when operated manually? Go to Step 2. Repair the mechanism. 2 Test the Delivery Belt Home Position Sensor. Run the Service Diagnostics Exit Belt Home Position Sensor test. Does the sensor operate? Go to Step 3. Replace the sensor. If the error persists, go to Step 3. 3 Test the Staple Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Staple Motor tests. Does the motor operate? Replace the Finisher Control Board. If the error persists, go to Step 4. Go to Step 4. 4 Check for +24 V to the Staple Motor. Disconnect CN59. Is there +24 V across CN59-1 and -2 <=> ground? Replace the Stack Handling Motor. Replace the harness. If the error persists, go to Step 5. 5 Check all pins of the Inverter Interface Cable for continuity. Disconnect CN1 and CN2 from the Finisher Control Board and the opposite end from the Inverter. Is the cable conductive? Replace the Inverter Power Supply. Replace the cable. |
| Error code: | F120 |
| Description: | Database abnormality: Databases do not run normally. |
| Remedy: | (1) Rebuild the databases. (Perform 08-684.) (2) If the error is not recovered, initialize the HDD. (Key in “2” at 08-690.) |
| Error code: | F130 |
| Description: | Controller to Engine Communications Failure An communications error was detected. |
| Causes: | • Engine Control Board, PL1.1.4 |
| Remedy: | 1 Cycle power to the printer. Does the error persist? Go to Step 2. Complete 2 Reseat the CUIF connector. Does the error persist? Replace the Engine Control Board. If the error persists, replace the Image Processor Board Complete |
