Toshiba FC310

Рейтинг

Парткаталог
Коды ошибок

Модули

ASM-OPTICS-2

ASM-OPTICS-1

ASM-PAPER-EXIT

ASM-FUSER-2

ASM-CRG-2

ASM-ELECTRIC

ASM-BYPASS

ASM-ALGINING

ASM-TBU-TRAY-2

ASM-FEEDER-2

ASM-BASE-FRAME

ASM-EPU-CHARGER

ASM-TRANSPORT-BELT

ASM-ADU-GUIDE

ASM-EPU-DRIVE

ASM-EPU-FRAME

ASM-FRONT-FRAME

ASM-FEED-DRIVE

ASM-EPU-DEVELOPER-1

ASM-CRG-1

ASM-EPU-DEVELOPER-2

ASM-USED-TONER

ASM-TBU-TRAY-1

ASM-REAR-FRAME-1

ASM-COVER-2

ASM-REAR-FRAME-2

ASM-FUSER-DRIVE

ASM-SIZE-INDICATOR

ASM-CONTROL-PANEL

ASM-FEEDER-1

ASM-CASSETTE

ASM-EPU-CLEANER

ASM-COVER-1

ASM-BYPASS-FEEDER

ASM-FUSER-1

ASM-LASER-SCAN

Детали ASM-EPU-DEVELOPER-1

Деталь:	SEAL-ARM-F3
Парткод:	4406527230

Деталь:	SPC050-045-0080
Парткод:	44065281 70

Деталь:	SNR-ATS-31 0
Парткод:	4406567050

Деталь:	STOPPER-ATS
Парткод:	4406527840

Деталь:	ASM-DEV-Y-314
Парткод:	4421 8040000

Деталь:	ASM-DEV-MCK314
Парткод:	4421 8050000

Деталь:	COV-DEV-L
Парткод:	4406527900

Деталь:	MIXER-U-31 4
Парткод:	4421 8055000

Деталь:	WAS06-12-Z25-P
Парткод:	4406528000

Деталь:	MIXER-L-31 4
Парткод:	4421 8056000

Деталь:	K-SHTR-DEV
Парткод:	4406527340

Деталь:	K-BUSH-MIXER-F
Парткод:	440652751 0

Деталь:	GEAR-08H025-06L
Парткод:	4406527540

Деталь:	GEAR-08H025-06R
Парткод:	4406527550

Деталь:	K-BUSH-MIXER-R
Парткод:	4406527560

Деталь:	ASM-DEV-FRM-Y
Парткод:	4406526600

Деталь:	ASM-DEV-FRM-MCK
Парткод:	4406526620

Деталь:	LEVER-SHUT
Парткод:	4406527800

Деталь:	ROLL-TNR-RE
Парткод:	4406528030

Деталь:	SEAL-SQ-RLR
Парткод:	4406528040

Деталь:	BUSH-ROL-T
Парткод:	4406528050

Деталь:	WAS-POLY-3
Парткод:	4406527970

Деталь:	RCHT-RE
Парткод:	4406528060

Деталь:	ASM-RLR-MGN-F31 4
Парткод:	4421 8060000

Деталь:	BRG-L1680DDR
Парткод:	4406531 920

Деталь:	CLAW-RCHT
Парткод:	4406527070

Деталь:	LBL-YELLOW
Парткод:	44065501 40

Деталь:	LBL-MAGENTA
Парткод:	44065501 50

Деталь:	LBL-CYAN
Парткод:	44065501 60

Деталь:	LBL-BLACK
Парткод:	44065501 70

Деталь:	SPC-1-RCHT
Парткод:	4406528140

Деталь:	GEAR-08S01 8-08
Парткод:	4406527050

Деталь:	WAS-POLY-7
Парткод:	4406527990

Деталь:	BRG-L1650HHR
Парткод:	4406531 930

Деталь:	K-DOCTOR-31 0
Парткод:	4406527080

Деталь:	BUSH-DEV-F-U
Парткод:	4406528250

Деталь:	K-BUSH-DEV-F-U
Парткод:	4406527240

Деталь:	PUSHER-DEV-F
Парткод:	4406527270

Деталь:	PUSHER-DEV-R
Парткод:	4406527280

Деталь:	ADJ-RLR-MGN
Парткод:	4406527290

Деталь:	WAS-POLY-4
Парткод:	4406527980

Деталь:	SHEET-MGN-F31 4
Парткод:	4421 8075000

Деталь:	SHEET-MGN-R31 4
Парткод:	4421 8076000

Деталь:	ASM-TERM-BIAS-D
Парткод:	4406527730

Деталь:	SFT-IDL-MIXER
Парткод:	4406527700

Деталь:	GEAR-08S01 8-06
Парткод:	440652771 0

Деталь:	BUSH-6-GCB
Парткод:	4407734980

Деталь:	STOP-RING-6-5
Парткод:	4407972860

Деталь:	SPC075-055-0330
Парткод:	4406527790

Деталь:	CPG-MIXER
Парткод:	4406527690

Деталь:	GEAR-08S01 4-06
Парткод:	4406527680

Деталь:	SPC080-050-0260
Парткод:	4406527780

Деталь:	SEAL-ARM-F1
Парткод:	4406526930

Деталь:	MYLAR-DEV-Y
Парткод:	44065281 90

Деталь:	BRKT-CLN-DRV
Парткод:	4406527630

Деталь:	K-BRKT-CLN-DRV
Парткод:	4406527620

Деталь:	RR/E-4-ZC
Парткод:	X0-01265000

Деталь:	RR/E-2-ZC
Парткод:	X0-01263000

Деталь:	S/BID-M3X6-NC
Парткод:	X0-01 277000

Деталь:	PTBR3006MSZN3A
Парткод:	4842040495

Деталь:	S/PAN/SWWS-M3X1 6-ZC
Парткод:	X0-0011 9000

Коды ошибок

C05

C06

C0A

C11

C12

C13

C14

C15

C16

C18

C27

C28

C29

C31

C33

C35

C38

C39

C3A

C3B

C3C

C3D

C3E

C3F

C41

C42

C43

C44

C46

C47

C48

C57

C5A

C5B

C5C

C72

C73

C74

C82

C94

C9A

C9B

C9D

C9E

CA1

CA2

CB1

CB2

CB3

CB4

CB5

CB6

CB7

CB8

CB9

CBA

CBB

CBC

CBD

CBE

CBF

CD1

CD2

CD3

CD4

CD5

CD6

CD7

CD9

CDA

CDB

CE1

CE2

CE3

CE4

CE5

CE6

CE9

CF1

E01

E02

E03

E11

E12

E13

E14

E15

E16

E19

E21

E22

E23

E24

E25

E26

E41

E42

E43

E45

E46

E50

E51

E52

E54

E71

E72

E73

E79

E9F

EA1

EA2

EA3

EA4

EA5

EA6

EA8

EA9

EAA

EAB

EAC

EAE

EB7

EC2

EC3

F07

F09

F10

F11

F12

F13

F51

Деталь:	S/PAN/SWWP - M3X30 - ZC
Парткод:	X0-001 37000

Деталь:	K - HLDR - THRM - 314
Парткод:	4421 7825000

Деталь:	S/PAN/SWWS - M3X8 - ZC
Парткод:	X0-00072000

Деталь:	S/PAN/SWWP - M4X8 - ZC
Парткод:	X0-001 61 000

Деталь:	HTR - 115 - 550W - U
Парткод:	4421 9844000

Деталь:	HTR - 127 - 550W - U
Парткод:	4421 9846000

Деталь:	PWA - F - LGC - 314S
Парткод:	44220561 000

Деталь:	S/TPS/BID - 3X8 - ZB
Парткод:	X0-01 531 000

Error code:	C05
Description:	ADU motor rotation abnormal
Causes:	317 After the master compression motor on the first print drum side or second print drum side begins to apply a compression force, the compression detection activates and the other disposal box exceeds 90% capacity before the FG count exceeds the specified volume (Expected disposal box full).
Remedy:	Is the ADU motor rotating properly? N: 1. Check if the harness between the LGC board and the ADU drawer connector is open-circuited. 2. Check if the harness between the switching power supply and the ADU drawer connector is open-circuited. 3. Check if any of the connectors J101, J102 and J104 on the LGC board is disconnected. 4. Reduce the mechanical load on the motor by adjusting the drive system. Remove foreign matter if any. 5. Replace the LGC board. Y: Are the pins B2 and B4 of the connector J104 on the LGC board always at the level "L"? N: 1. Check if the connector J104 on the LGC board is disconnected. 2. Check if any conductor pattern on the LGC board is open- or short-circuited. 3. Check if any harness is open-circuited or any connector pin is disconnected. 4. Replace the LGC board. Y: 1. Check if any conductor pattern on the LGC board is open- or short-circuited. 2. Replace the LGC board.

Error code:	C06
Description:	Feed motor rotation abnormal
Causes:	859 No paper in Tray No.1
Remedy:	Is the paper feed motor rotating properly? N: 1. Check if the connector J41 of the paper feed motor is disconnected. 2. Check if the connector J109 on the LGC board is disconnected. 3. Check if the connector J703 of the switching power supply is disconnected. 4. Check if the harness between the LGC board and the paper feed motor is open-circuited. 5. Check if the harness between the switching power supply and the paper feed motor is open-circuited. 6. Check if any harness is open-circuited or any connector pin is disconnected. 7. Rotate the motor manually, clockwise as seen from its back, and if the motor load is abnormal, remove any foreign matter from the drive unit. 8. Replace the paper feed motor. 9. Replace the LGC board. Y: Are the pins A6 and A10 of the connector J109 on the LGC board always at the level "L"? N: 1. Check if the connector J41 of the paper feed motor is disconnected. 2. Check if the connector J109 on the LGC board is disconnected. 3. Check if any conductor pattern on the LGC board is open- or short-circuited. 4. Check if any harness is open-circuited or any connector pin is disconnected. 5. Replace the LGC board. 6. Replace the paper feed motor. Y: 1. Check if any conductor pattern on the LGC board is open- or short-circuited. 2. Replace the LGC board. 3. Replace the paper feed motor.

Деталь:	DUMP-MOT-SCN
Парткод:	440651 7030

Деталь:	PULLEY-Z26-2GT
Парткод:	4408675930

Деталь:	FRANGE-PLY-SCAN
Парткод:	44079761 60

Деталь:	SHAFT-DRV-SCN
Парткод:	440651 7940

Error code:	C0A
Description:	Developer motor rotation abnormal
Remedy:	Is the developer motor rotating properly? N: 1. Check if the connector J41 or J43 of the developer motor is disconnected. 2. Check if the connector J109 on the LGC board is disconnected. 3. Check if the connector J703 of the switching power supply is disconnected. 4. Check if the harness between the LGC board and the developer motor is open-circuited. 5. Check if the harness between the switching power supply and the developer motor is open-circuited. 6. Check if any harness is open-circuited or any connector pin is disconnected. 7. Rotate the motor manually, counterclockwise as seen from its back, and if the motor load is abnormal, remove any foreign matter from the drive unit. (Do not try to rotate the motor clockwise as seen from its back.) 8. Replace the developer motor. 9. Replace the LGC board. Y: Are the pins B12 and B16 of the connector J109 on the LGC board always at the level "L"? N: 1. Check if the connector J41 of the developer motor is disconnected. 2. Check if the connector J109 on the LGC board is disconnected. 3. Check if any conductor pattern on the LGC board is open- or short-circuited. 4. Check if any harness is open-circuited or any connector pin is disconnected. 5. Replace the LGC board. 6. Replace the developer motor. Y: 1. Check if any conductor pattern on the LGC board is open- or short-circuited. 2. Replace the LGC board. 3. Replace the developer motor.

Error code:	C11
Description:	ADU paper side guide operation abnormal
Remedy:	Is the ADU pushed in securely to the copier? N: Push in the ADU securely to the copier. Y: Has the timing belt for driving the paper side guide come off? Y: Put the belt on properly. N: Is the connector J104 on the LGC board disconnected? Is the harness between the LGC board and the ADU drawer connector open-circuited? Y: Reconnect the connector. Replace the harness. N: 1. Replace the LGC board. 2. Replace the ADU.

Error code:	C12
Description:	ADU paper end guide operation abnormal
Remedy:	Is the ADU pushed in securely to the copier? N: Push in the ADU securely to the copier. Y: Has the timing belt for driving the paper end guide come off? N: Is the connector J104 on the LGC board disconnected? Is the harness between the LGC board and the ADU drawer connector open-circuited? Y: Reconnect the connector. Replace the harness. N: 1. Replace the LGC board. 2. Replace the ADU.

Error code:	C13
Description:	1st cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C14
Description:	2nd cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C15
Description:	3rd cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C16
Description:	4th cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C18
Description:	LCF tray operation abnormal
Remedy:	Is the harness between the LGC board and the LCF unit open-circuited? Is the relay connector of the harness between the LGC board and the LCF unit or the connector J105 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: Are the switches and sensors in the LCF unit working properly? Y: 1. Replace the LCF tray motor. 2. Replace the LGC board. N: 1. Replace the sensors and switches. 2. Replace the LCF drive PC board or the LCF tray-down switch PC board. 3. Replace the LGC board.

Error code:	C27
Description:	Carriage home position sensor not turning OFF within a fixed time
Causes:	• If the Master sensor does not find master on the Drum when the Drum is at 79° during the printing movement.
Remedy:	Are the carriages stuck at a point other than the home position? Y: Check the SCM and SDV boards for any abnormal circuit. N: 1. Check if any connector pin is disconnected, or any harness is open- or short-circuited. 2. Check the scan motor drive pulley if its screws are loose. 3. Check if any conductor pattern on the SDV board is open- or short-circuited. 4. Check if any conductor pattern on the SCM board is open- or short-circuited. 5. Replace the SDV board. 6. Replace the SCM board.

Error code:	C29
Description:	Exposure lamp disconnection detected
Remedy:	Does the exposure lamp light? Y: 1. Check the CCD and SCM boards for any disconnected connector. 2. Check the shading correction plate of the original-width indicator unit if it is dusty. 3. Check the CCD board for any open- or short-circuited conductor pattern. 4. Check the SCM board for any open- or short-circuited conductor pattern. 5. Replace the SCM board. 6. Replace the lens unit. N: 1. Check if the lamp connector is disconnected. 2. Check the SCM board if any pin of connectors J7-1, -2 and -3 is disconnected or any harness is open- or short-circuited. 3. Check the SCM board for any open- or short-circuited conductor pattern. 4. Replace the SCM board. 5. Replace the inverter. 6. Replace the exposure lamp.

Toshiba FC310

Модули

Детали ASM-EPU-DEVELOPER-1

Коды ошибок

Описание

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку

Error code:	C31
Description:	Used toner transport motor rotation abnormal
Causes:	• If the Paper receiving sensor does not find paper when the Drum is at Position-A during the printing operation and the Paper sensor finds a paper at next Drum Position-A.
Remedy:	Is the harness between the LGC board and the used toner transport motor open-circuited? Is the connector J123 or J102 on the LGC board, the relay connector or the used toner transport motor connector disconnected? Y: Replace the harness. Reconnect the connector. N: Is used toner jammed? Is any abnormal mechanical load found? Y: 1. Remove the jammed used toner. 2. Check for any foreign matter in the drive system. 3. Check the bearing of the used toner transport auger for any abnormality. 4. Check if the toner bag is covered with used toner. N: 1. Replace the used toner transport motor. 2. Replace the LGC board.

Error code:	C33
Description:	Developer removal shutter abnormal
Causes:	• If the Paper sensor does not detect paper at Drum angle 135° within three Drum rotations during printing.
Remedy:	Reduce the mechanical load by adjusting the drive system. Remove any foreign matter. Is the connector J115 on the LGC board disconnected? Y: Reconnect the connector. N: Replace the LGC board.

Error code:	C35
Description:	Transfer belt unit contact/release operation abnormal
Remedy:	Reduce the mechanical load by adjusting the drive system. Remove any foreign matter. Is the harness between the LGC board and the transfer/transport unit drawer connector, or the harness inside the transfer/transport unit open-circuited? Is the transfer belt contact/release drive motor connector, LGC board connector J115 or J102, transfer belt home position switch connector, or transfer belt limit switch connector disconnected? Is the transfer belt home position switch or the transfer belt limit switch defectively installed? Y: 1. Replace the harness. Reconnect the connector. 2. Reinstall the transfer belt home position switch or the transfer belt limit switch securely. N: 1. Replace the transfer belt home position switch and the transfer belt limit switch. 2. Replace the transfer belt contact/release drive motor. 3. Replace the LGC board.

Error code:	C38
Description:	Auto-toner error (K)
Causes:	• During the Original scanning, if the Original IN sensor keeps detecting Original (sensor light reflected) and does not stop detecting within 4945 pulses after the Read pulse motor activates.
Remedy:	Is the harness between the LGC board and the EPU drawer connector open-circuited? Is any harness inside the EPU or the auto-toner sensor harness open-circuited? Is the auto-toner sensor connector or the connector J120 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the auto-toner sensor. 2. Replace the LGC board.

Error code:	C39
Description:	Auto-toner error (C)
Remedy:	Is the harness between the LGC board and the EPU drawer connector open-circuited? Is any harness inside the EPU or the auto-toner sensor harness open-circuited? Is the auto-toner sensor connector or the connector J120 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the auto-toner sensor. 2. Replace the LGC board.

Error code:	C3A
Description:	Auto-toner error (M)
Remedy:	Is the harness between the LGC board and the EPU drawer connector open-circuited? Is any harness inside the EPU or the auto-toner sensor harness open-circuited? Is the auto-toner sensor connector or the connector J120 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the auto-toner sensor. 2. Replace the LGC board.

Error code:	C3B
Description:	Auto-toner error (Y)
Remedy:	Is the harness between the LGC board and the EPU drawer connector open-circuited? Is any harness inside the EPU or the auto-toner sensor harness open-circuited? Is the auto-toner sensor connector or the connector J120 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the auto-toner sensor. 2. Replace the LGC board.

Error code:	C3C
Description:	Main charger wire cleaning abnormal (K)
Remedy:	Is the harness between the LGC board and the EPU drawer connector or any harness inside the EPU open-circuited? Is the wire cleaner drive motor connector, the connector J120 on the LGC board, the connector of the wire cleaner home position switch, or the connector of the wire cleaner limit switch disconnected? Has the wire cleaner home position switch or the wire cleaner limit switch defectively installed or come off? Y: 1. Reconnect the connector. Replace the harness. 2. Reinstall the wire cleaner home position switch or the wire cleaner limit switch securely. N: Is the main charger securely installed? N: Reinstall the main charger. Y: Is the mechanical load too heavy? Y: 1. Check if the cleaning pad is in normal contact with the main charger wire. 2. Eliminate any foreign matter present in the drive system. 3. Check if any movable component is abnormally worn. 4. Clean the wire cleaner drive auger and remove stains or foreign matters. 5. Clean the slidable surface of the charger case and remove stains or foreign matters. N: 1. Replace the wire cleaner home position switch or the wire cleaner limit switch. 2. Replace the wire cleaner drive motor. 3. Replace the LGC board.

Error code:	C3D
Description:	Main charger wire cleaning abnormal (C)
Remedy:	Is the harness between the LGC board and the EPU drawer connector or any harness inside the EPU open-circuited? Is the wire cleaner drive motor connector, the connector J120 on the LGC board, the connector of the wire cleaner home position switch, or the connector of the wire cleaner limit switch disconnected? Has the wire cleaner home position switch or the wire cleaner limit switch defectively installed or come off? Y: 1. Reconnect the connector. Replace the harness. 2. Reinstall the wire cleaner home position switch or the wire cleaner limit switch securely. N: Is the main charger securely installed? N: Reinstall the main charger. Y: Is the mechanical load too heavy? Y: 1. Check if the cleaning pad is in normal contact with the main charger wire. 2. Eliminate any foreign matter present in the drive system. 3. Check if any movable component is abnormally worn. 4. Clean the wire cleaner drive auger and remove stains or foreign matters. 5. Clean the slidable surface of the charger case and remove stains or foreign matters. N: 1. Replace the wire cleaner home position switch or the wire cleaner limit switch. 2. Replace the wire cleaner drive motor. 3. Replace the LGC board.

Error code:	C3E
Description:	Main charger wire cleaning abnormal (M)
Remedy:	Is the harness between the LGC board and the EPU drawer connector or any harness inside the EPU open-circuited? Is the wire cleaner drive motor connector, the connector J120 on the LGC board, the connector of the wire cleaner home position switch, or the connector of the wire cleaner limit switch disconnected? Has the wire cleaner home position switch or the wire cleaner limit switch defectively installed or come off? Y: 1. Reconnect the connector. Replace the harness. 2. Reinstall the wire cleaner home position switch or the wire cleaner limit switch securely. N: Is the main charger securely installed? N: Reinstall the main charger. Y: Is the mechanical load too heavy? Y: 1. Check if the cleaning pad is in normal contact with the main charger wire. 2. Eliminate any foreign matter present in the drive system. 3. Check if any movable component is abnormally worn. 4. Clean the wire cleaner drive auger and remove stains or foreign matters. 5. Clean the slidable surface of the charger case and remove stains or foreign matters. N: 1. Replace the wire cleaner home position switch or the wire cleaner limit switch. 2. Replace the wire cleaner drive motor. 3. Replace the LGC board.