Canon imageCLASS MF913w
Рейтинг
Модули
102A INTERNAL COMPONENTS 2 120V
100AEXTERNAL COVERS, PANELS, ETC.
102FINTERNAL COMPONENTS 2 230V
400 READER ASSEMBLY
101A INTERNAL COMPONENTS 1 120V
101H INTERNAL COMPONENTS 1 230V
Детали 100AEXTERNAL COVERS, PANELS, ETC.
Деталь: | LINK, PRESSURE RELEASE LEFT |
Парткод: | RC4-7736-000 |
Деталь: | LINK, PRESSURE RELEASE RIGHT |
Парткод: | RC4-7737-000 |
Деталь: | ROLLER, PAPER PICK-UP |
Парткод: | RL1 -2593-000 |
Деталь: | SEPARATION PAD ASSY |
Парткод: | RM2-6957-000 |
Деталь: | ENVIRONMENT SENSOR PCB ASSY |
Парткод: | FM2-A858-000 |
Деталь: | TRANSFER ASSY |
Парткод: | FM1-T714-000 |
Деталь: | FIXING ASSY (220-240V) |
Парткод: | RM2-1651-000 |
Деталь: | FIXING FILM ASSY |
Парткод: | RM2-6962-000 |
Деталь: | DELIVERY SENSOR PCB ASSY |
Парткод: | RM2-8279-000 |
Деталь: | TRANSFER ROLLER ASSY |
Парткод: | RM2-1660-000 |
Деталь: | LASER SCANNER ASSY |
Парткод: | RM2-1662-000 |
Деталь: | MOTOR PCB ASSY |
Парткод: | RM2-8251 -000 |
Деталь: | PAPER PICK-UP SENSOR PCB ASSY |
Парткод: | FM2-A859-000 |
Деталь: | SOLENOID |
Парткод: | RK2-7601-000 |
Деталь: | LABEL, ATTENTION |
Парткод: | RU5-8841-000 |
Деталь: | SCREW, TAP, M3X6 |
Парткод: | XA9-1503-000 |
Цена: | 340 ₽ |
Деталь: | COVER, LEFT |
Парткод: | FE8-8337-000 |
Деталь: | COVER, RIGHT |
Парткод: | FE8-8338-000 |
Деталь: | COVER, REAR |
Парткод: | FL1-5934-000 |
Деталь: | HOLDER, SLIDER |
Парткод: | FE8-8369-000 |
Деталь: | SPRING, LEAF |
Парткод: | FE8-8791-000 |
Деталь: | COVER, FACE-DOWN |
Парткод: | FL1-5784-000 |
Деталь: | CONTROL PANEL ASSY |
Парткод: | FM1-T517-000 |
Деталь: | CARTRIDGE DOOR ASSY |
Парткод: | FM1-U129-000 |
Деталь: | LABEL, HIGH TMP. CAUTION |
Парткод: | FE8-8773-000 |
Деталь: | TRAY, MULTI-PURPOSE |
Парткод: | FE8-6602-000 |
Деталь: | PLATE, EXTENSION |
Парткод: | FE8-6603-000 |
Деталь: | STOPPER,PAPER |
Парткод: | FE8-6604-000 |
Деталь: | COVER, FRONT |
Парткод: | FE8-8336-000 |
Деталь: | KEY TOP, POWER |
Парткод: | FL1-5288-000 |
Деталь: | COVER, DUST |
Парткод: | FE8-7074-000 |
Деталь: | SCREW, TAP, M3X6 |
Парткод: | XA9-1503-000 |
Цена: | 340 ₽ |
Деталь: | LINK, PRESSURE RELEASE LEFT |
Парткод: | RC4-7736-000 |
Деталь: | LINK, PRESSURE RELEASE RIGHT |
Парткод: | RC4-7737-000 |
Деталь: | ROLLER, PAPER PICK-UP |
Парткод: | RL1 -2593-000 |
Деталь: | SEPARATION PAD ASSY |
Парткод: | RM2-6957-000 |
Деталь: | ENVIRONMENT SENSOR PCB ASSY |
Парткод: | FM2-A858-000 |
Деталь: | TRANSFER ASSY |
Парткод: | FM1-T714-000 |
Деталь: | FIXING ASSY (220-240V) |
Парткод: | RM2-1651-000 |
Деталь: | FIXING FILM ASSY |
Парткод: | RM2-6962-000 |
Деталь: | DELIVERY SENSOR PCB ASSY |
Парткод: | RM2-8279-000 |
Деталь: | TRANSFER ROLLER ASSY |
Парткод: | RM2-1660-000 |
Деталь: | LASER SCANNER ASSY |
Парткод: | RM2-1662-000 |
Деталь: | MOTOR PCB ASSY |
Парткод: | RM2-8251 -000 |
Деталь: | PAPER PICK-UP SENSOR PCB ASSY |
Парткод: | FM2-A859-000 |
Деталь: | SOLENOID |
Парткод: | RK2-7601-000 |
Деталь: | LABEL, ATTENTION |
Парткод: | RU5-8841-000 |
Деталь: | SCREW, TAP, M3X6 |
Парткод: | XA9-1503-000 |
Цена: | 340 ₽ |
Деталь: | BELT, TIMING |
Парткод: | FC0-8550-000 |
Деталь: | SHAFT, DAMPER |
Парткод: | FC0-8560-000 |
Деталь: | SLIDER |
Парткод: | FE8-8368-000 |
Деталь: | SPACER, CIS |
Парткод: | FE8-8917-000 |
Деталь: | CONTACT IMAGE SENSOR,HV12I-V02 |
Парткод: | FK4-2086-000 |
Деталь: | CABLE, FLEXIBLE FLAT |
Парткод: | FK4-5074-000 |
Деталь: | CABLE, FLEXIBLE FLAT |
Парткод: | FK4-5092-000 |
Деталь: | IDLER PULLEY HOLDER ASSY |
Парткод: | FL3-5062-000 |
Деталь: | CIS DRIVE MOTOR ASSY |
Парткод: | FM0-0590-000 |
Деталь: | COPYBOARD GLASS ASSY |
Парткод: | FM1-T515-000 |
Деталь: | SPRING, COMPRESSION |
Парткод: | FU6-2873-000 |
Деталь: | COVER, COPYBOARD |
Парткод: | FE8-8363-000 |
Деталь: | PANEL, COPYBOARD |
Парткод: | FE8-8916-000 |
Деталь: | CABLE, FLEXIBLE FLAT |
Парткод: | FK4-5089-000 |
Деталь: | CABLE, FLEXIBLE FLAT |
Парткод: | RM2-8281 -000 |
Деталь: | CABLE, FLEXIBLE FLAT |
Парткод: | RM2-8282-000 |
Деталь: | L.V. POWER SUPPLY PCB ASSY |
Парткод: | FM1-U126-000 |
Деталь: | ENGINE CONTROL PCB ASSY |
Парткод: | FM2-A864-000 |
Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
Парткод: | FM2-C973-000 |
Деталь: | POWER SWITCH PCB ASSY |
Парткод: | RM2-8273-000 |
Деталь: | CORE, FERRITE |
Парткод: | WE8-6481-000 |
Деталь: | SCREW, W/WASHER, M3X8 |
Парткод: | XA9-1420-000 |
Цена: | 1 100 ₽ |
Деталь: | SCREW, TAP, M3X6 |
Парткод: | XA9-1503-000 |
Цена: | 340 ₽ |
Деталь: | MODULE, WLAN |
Парткод: | FK4-4651-000 |
Деталь: | CABLE, FLEXIBLE FLAT |
Парткод: | FK4-5071-000 |
Деталь: | CABLE, FLEXIBLE FLAT |
Парткод: | FK4-5089-000 |
Деталь: | CABLE, FLEXIBLE FLAT |
Парткод: | RM2-8281 -000 |
Деталь: | CABLE, FLEXIBLE FLAT |
Парткод: | RM2-8282-000 |
Деталь: | L.V. POWER SUPPLY PCB ASSY |
Парткод: | FM1-U128-000 |
Деталь: | ENGINE CONTROL PCB ASSY |
Парткод: | FM2-A864-000 |
Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
Парткод: | FM2-C973-000 |
Деталь: | POWER SWITCH PCB ASSY |
Парткод: | RM2-8273-000 |
Деталь: | CORE, FERRITE |
Парткод: | WE8-6481-000 |
Деталь: | SCREW, W/WASHER, M3X8 |
Парткод: | XA9-1420-000 |
Цена: | 1 100 ₽ |
Деталь: | SCREW, TAP, M3X6 |
Парткод: | XA9-1503-000 |
Цена: | 340 ₽ |
Деталь: | MODULE, WLAN |
Парткод: | FK4-4651-000 |
Деталь: | CABLE, FLEXIBLE FLAT |
Парткод: | FK4-5071-000 |
Коды ошибок
0001
0002
0003
0004
000C
000E
000F
E000-0000
E001-0000
E003-0000
E004-0000
E015-0001
E066-0000
E100-0001
E110-0000
E110-0001
E196-0001
E196-2000
E202-0002
E225-0001
E301-0001
E733-0000
E744-0002
E744-4000
E744-6000
E760-0001
E808-0000
Описание
Error code: | 0001 |
Display: | Main motor failure CODE (001) Turn power off, on |
Description: | Main Motor Failure The Main Motor lock signal remains HIGH for a predetermined consecutive period of time while the Main Motor remains energized. |
Causes: | • Main Motor, PL9.1.6 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
Remedy: | 1 Check the Engine Control Board connector P/J8. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Check the Main Motor for proper positioning. Is the motor engaged with the gears? Go to step 3. Reseat the motor drive properly. If the problem persists, go to step 3. 3 Check the operation of the Main Motor. Is the motor faulty? Replace the motor. If the problem persists, go to step 4. Go to step 4. 4 On the Engine Control Board, check P/J2 at pins 1, 5, and 7 for +24V. Are the voltages present? Go to step 5. Go to step 6. 5 Replace the Engine Control Board. Does the problem persist? Go to step 5. Complete. 6 Replace the Power Supply. Complete. |
Error code: | 0002 |
Description: | Disorder of communication with Sub CPU This occurs when the Sub CPU is not detected after turning on the machine |
Causes: | Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board. |
Remedy: | Check cable connection between Main Board and Servo Board. Check cable connection between Main Board and Heater Board. Check the other cable connections of Servo Board Heater Board replacement Servo Board replacement Main Board replacement Flexible cable replacement |
Error code: | 0003 |
Description: | DIPSW model setting error A setup about the model of DIPSW is set up in an unsuitable combination. |
Causes: | DIPSW setup error DIPSW defect Main Board defect |
Remedy: | 1) Check the DIPSW setup 2) Replacement the Main Board |
Error code: | 0004 |
Description: | Sub CPU SRAM error |
Causes: | SRAM is broken. |
Remedy: | Servo Board replacement |
Error code: | 000C |
Description: | SCAN MOTOR ERROR |
Causes: | Feed Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.) Feed Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.) |
Remedy: | < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. ) |
Error code: | 000E |
Description: | Internal residual Jam |
Causes: | TOP Sensor/Fixing Delivery Sensor/Fixing Paper Width Sensor PS3/PS4/PS5 |
Error code: | 000F |
Description: | Door open Jam |
Causes: | TOP Sensor/Fixing Delivery Sensor/Fixing Paper Width Sensor PS3/PS4/PS5 |
Error code: | E000-0000 |
Description: | Startup error The temperature detected by the main or sub thermistor does not rise to the specified value during startup control. |
Causes: | The detection temperature of the main thermistor did not increase after start of the power distribution to the heater. |
Remedy: | - Check the fixing film connector. - Replace the fixing film unit. - Replace the DC controller PCB. |
Error code: | E001-0000 |
Description: | Abnormally high temperature (detected by main thermistor) The main thermistor detected an abnormally high temperature 235 deg C) during temperature control |
Causes: | The main thermistor detected a temperature of higher than 255 degree C. |
Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
Error code: | E003-0000 |
Description: | Abnormally low temperature (detected by main thermistor) After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
Causes: | The main thermistor detected a temperature of lower than 120 degree C for more than 1 second when 20 seconds elapsed after start of the power distribution to the heater. |
Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
Error code: | E004-0000 |
Description: | Fixing power supply drive circuit error |
Causes: | 43 to 57Hz could not be detected continuously for more than 5 seconds when zero cross detection started. |
Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the DC Controller Board. (2) Replace the Fixing Assembly. |
Error code: | E015-0001 |
Description: | Cassette 1 lift up motor error |
Causes: | Cassette 1 lift up motor error |
Remedy: | Reconnect the connector J151 on the DC controller PCB and the relay connector J742. Check the cassette media stack surface sensor in the sensor monitor mode. If a failure is found, replace the lifter drive unit. Replace the lifter drive unit. |
Error code: | E066-0000 |
Description: | Environment sensor failure |
Causes: | Environment sensor failure |
Remedy: | Replace the environment sensor. |
Error code: | E100-0001 |
Description: | Error detection on any of scanner motor, laser unit, and BD detection at scanner area. |
Causes: | Magenta optical assembly failure |
Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Laser Scanner Unit. (2) Replace the DC Controller Board. |
Error code: | E110-0000 |
Description: | Optical assembly error (Scanner motor) |
Causes: | Optical assembly error (Scanner motor initial operation failure) |
Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
Error code: | E110-0001 |
Description: | Optical assembly error (Scanner motor) |
Causes: | Optical assembly error (Scanner motor rotation failure) |
Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
Error code: | E196-0001 |
Description: | Image processor PCB failure Error on writing and readout ROM of image processor PCB (mainn ROM). |
Causes: | D-con update for the optional cassette is not completed. |
Remedy: | - Putting the switch on/off of the power supply. - Replace the image processor PCB. |
Error code: | E196-2000 |
Description: | ROM read/write error (Error in storing each setting values for user mode / service mode / factory mode) |
Causes: | Error in writing in/reading from ROM (storing settings) Cause: Problem in main controller PCB |
Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Update the set of the Controller Firmware (2) Replace the Main Controller Board. |
Error code: | E202-0002 |
Description: | Contact Sensor HP error, Failure in return |
Causes: | Reader HP homeward fault - Replace reader unit. The CCD unit moves forward, but does not move to the home position. |
Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board. |
Error code: | E225-0001 |
Description: | Light intensity of a lamp is less or equal to the criteria |
Causes: | When the light intensity is at the reference level or below at shading. |
Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board. |
Error code: | E301-0001 |
Description: | Insufficient light intensity in shading |
Causes: | Insufficient light intensity at shading. |
Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board |
Error code: | E733-0000 |
Description: | Erroneous communication between controller and printer Cannot communicate with the printer at startup. |
Causes: | Printer communication error (communication error at initial communication and negotiation packet error) |
Remedy: | - Check the connectors of the DC controller PCB and image processor PCB for normal connection. - Check the power supply of the printer (Check whether initialization is performed at startup). - Replace the DC controller PCB or image processor PCB. |
Error code: | E744-0002 |
Description: | Language file/boot ROM/USB memory error The language file is longer than the permitted size. |
Causes: | Language file size error The language file is longer than the permitted size. |
Remedy: | Download a language file of the correct version. |
Error code: | E744-4000 |
Description: | Engine ID error (Invalid engine connection is detected) |
Causes: | Error in engine ID Detected illegal engine connection |
Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the DC Controller Board. (2) Update the Engine Firmware. (3) Update the set of the Controller Firmware |
Error code: | E744-6000 |
Description: | Communication error with Wireless LAN board. |
Causes: | Communication with the Wireless LAN PCB could not be established. |
Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Wireless LAN Board. (4) Replace the Main Controller Board. |
Error code: | E760-0001 |
Description: | Main Controller PCB error |
Causes: | An error occurred with the firmware of the Main Controller. |
Remedy: | 1. Update the set of the controller firmware. 2. Replace the Main Controller PCB. |
Error code: | E808-0000 |
Description: | Fixing drive circuit failure - The heater does not turn on. - A fixing drive motor failure was detected. |
Causes: | Printer detected failure in low-voltage power supply Cause: Failure in low-voltage power supply, problem in DC controller PCB |
Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the fixing drive motor. - Replace the DC controller PCB. - Replace the power supply PCB. |