Canon imagePROGRAF iPF TX-4000 MFP T36-AiO

Общие характеристики
Макс. формат	A0
Размещение	напольный
Цветность печати	цветная
Факс
Телефон
Тип устройства	МФУ
Сканер
Копир
Технология печати	термическая струйная
Количество цветов	5
Система непрерывной подачи чернил
Двусторонняя печать
Мин, объем капли	5 пл
Печать без полей
Пигментные чернила
Прямая печать
Макс, разрешение для ч/б печати
По X	2 400
По Y	1 200
Отправка изображения по e-mail
Стандарт WIA
Слайд-адаптер
Стандарт TWAIN
Тип сканера	протяжный
Макс. формат оригинала	A0
Макс, размер сканирования
По Y	1 520
По X	914
Разрешение сканера
По Х	1 200
Количество картриджей	5
Печать на:
Матовой бумаге
Рулоне
Карточках
Конвертах
CD/DVD
Этикетках
Цветной
Стандарт DECT
Беспроводная трубка
Проводная трубка
АОН
Языки управления
PDF
PostScript 2
PCL 5e
PostScript 3
PCL 5c
PCL 6
PostScript
Электронная сортировка
Брошюровщик
Сортер
Сортировка со сдвигом
Степлер
Wi-Fi 802.11n
Веб-интерфейс
Устройство для чтения карт памяти
Версия USB	3,0
Частота процессора	2
Емкость жесткого диска	500
Объем памяти	2 048
Работа от аккумулятора
Диагональ дисплея	15,6
Экран
Поддержка ОС
DOS
Windows
Mac OS
Потребляемая мощность
В режиме ожидания	3,6
При работе	107
Уровень шума
В режиме ожидания	35
При работе	51
Высота	1 168
Вес	114
Ширина	1 593
Глубина	984

Error code:	001111 2E3A
Description:	Paper feeding failure (upper roll) (support number: 1300)
Causes:	Feeding of the roll paper fails at the upper roll paper path (roll1). (from the paper feed sensor to the PE sensor in paper path)
Remedy:	1 Reload the roll paper. (Remove left paper pieces and check the top edge of the paper.) The error is removed Complete. The error is not removed Go to 2. 2 Replace the following parts from the top and check if the error is removed after each replacement. (from the loading sensor to the PE sensor) • ROLL PAPER FEED SENSOR UNIT. • HARNESS ASS’Y, RLNIP PF SNS. • PAPER ENTRY SENSOR. • DRIVE NIP ARM UNIT. • ACTIVE ROLL BRAKE UNIT. Adjustment and counter reset is necessary. 3 Check other suspected cause. • Media related cause (size, media type mismatch, paper turn-up at the top edge) • Curly end edge of the roll paper • Avoid the paper with strong stiffness or heavy roll paper.

Error code:	001112 2E3D
Description:	Paper feeding failure (support number: 1300)
Causes:	When the paper passes PAPER ENTRY SENSOR, the multi sensor fails to detect the paper edge. This error occurs when the LF roller is catching the paper.
Remedy:	1 Release the release lever. Reload the paper. (Check remained paper pieces and check the paper tip condition.) The error is removed Complete. The error is not removed Go to 2. 2 Check if the pinch roller is nipping the media. Nipping Replace PINCH ROLLER UNIT. Not nipping Replace PAPER ENTRY SENSOR. 3 Check other suspected cause. • Media related cause. (size, media type mismatch, turn-up at the tip of the paper) • Curly bottom tip of the roll paper. • Avoid the paper with strong stiffness or heavy roll paper.

Error code:	001113 2025
Description:	Upper roll drive overload (in roll paper loading) (support number: 1328)
Causes:	The electric current reached to the maximum loadable value at the upper ACTIVE ROLL BRAKE UNIT motor control in paper loading (between UPPER PAPER SET SENSOR and UPPER PAPER ENTRY SENSOR). <The assumed situation> • ACTIVE ROLL BRAKE UNIT receives load, e.g. due to touching the roll paper by the user, during roll paper front edge detection with UPPER PAPER SET SENSOR. • Heavy roll paper is being loaded.
Remedy:	1 Feed the roll paper again. When re-feeding is disabled, feed the paper manually.

Error code:	001113 2026
Description:	Lower roll drive overload (in roll paper loading) (support number: 1329)
Causes:	The electric current reached to the maximum loadable value at the lower ACTIVE ROLL BRAKE UNIT motor control in paper loading (between LOWER PAPER SET SENSOR and LOWER PAPER ENTRY SENSOR). <The assumed situation> • ACTIVE ROLL BRAKE UNIT receives load, e.g. due to touching the roll paper by the user, during roll paper front edge detection with LOWER PAPER SET SENSOR. • Heavy roll paper is being loaded.
Remedy:	1 Feed the roll paper again. When re-feeding is disabled, feed the paper manually.

Error code:	001113 2051
Description:	Unable to pick up the upper roll paper (in roll paper loading) (support number: 1326)
Causes:	UPPER PAPER SET SENSOR fails to detect the roll paper front edge in roll paper feeding. <The assumed situation> • The front edge of the roll paper does not peel off from the roll paper. • The spool does not rotate due to gear damage in paper feeding. • Sensor malfunction.
Remedy:	1 Feed the roll paper again. When re-feeding is disabled, feed the paper manually.

Error code:	001113 2052
Description:	Unable to pick up the upper roll paper (in roll paper loading) (support number: 1300)
Causes:	UPPER PAPER ENTRY SENSOR fails to detect the roll paper front edge within the specified time period after UPPER PAPER SET SENSOR detected the roll paper front edge.
Remedy:	1 Feed the roll paper again. When re-feeding is disabled, feed the paper manually.

Error code:	001113 2056
Description:	Upper roll paper not loaded (support number: 1034)
Causes:	UPPER PAPER SET SENSOR fails to detect loading of the roll paper in roll paper feeding.
Remedy:	1 Reload the roll paper.

Error code:	001215 200D
Description:	Paper detection failure (at the tip of the paper) (support number: 1322)
Causes:	The multi sensor fails to detect the tip of the cut sheet.
Remedy:	1 Check each condition. • The paper loading position. • Loading of curled paper. • Pulling out of cut sheets just before printing. 2 Check other suspected cause. • When using clear film, paper size may not be detected if ink is stained on the platen. In this case, open the top cover and clean the whole platen.

Error code:	001215 2016
Description:	Paper feeding failure (support number: 1300)
Causes:	The length of the cut paper in feed direction detected by PAPER ENTRY SENSOR during printing is different from that of which detected during paper feeding.* *The change of the cut paper feed amount due to some reasons such as paper jam may cause this error.
Remedy:	1 • Remove the paper when it is jamming inside. • Reload papers when papers are not jammed inside.

Error code:	001215 2E3C
Description:	Paper feeding failure (cut sheet) (support number: 1300, alarm code: -)
Causes:	PAPER ENTRY SENSOR detects no paper loaded on the printer when the printing starts.
Remedy:	1 Lift the release lever up, and reload the cut sheet.

Error code:	002121 2010
Description:	Skew (support number: 1317)
Causes:	During the paper feeding, the multi sensor detects that the paper edge at home position side moved +/-1mm or more (for cut paper, +/-2mm or more) off the original edge position per 300mm feeding.
Remedy:	1 • Reload the paper. • Remove the roll holder. Put the roll paper into the spool until it hits the frange. Set the roll holder to the printer. • Select “OFF” or “Loose” in [Skew detection accuracy] in the printer menu.* *Skew printing causes paper jam, failure in image, or stain on the platen, which may cause ink smear on the reverse side of the paper in the next printing.

Error code:	002221 200C
Description:	Paper detection failure (at the tip of the paper) (support number: 1322)
Causes:	The multi sensor fails to detect the tip of the roll paper.
Remedy:	1 Check each condition. • The paper loading position. • Loading of curled paper. • Pulling out of roll paper just before printing. 2 Check other suspected cause. • When using clear film, paper size may not be detected if ink is stained on the platen. In this case, open the top cover and clean the whole platen.

Error code:	002221 2017
Description:	Paper detection failure (at the right edge of the paper) (support number: 1322)
Causes:	The multi sensor detected that the paper edge at home position side was off 5mm during paper feeding.* *Loading the paper being off the reference position may also cause this error.
Remedy:	1 Lift the lever up to release the error. Check the right edge position, and reload or replace the paper.

Error code:	002221 2018
Description:	Paper detection failure (at the left edge of the paper) (support number: 1322)
Causes:	The multi sensor failed to detect the away side paper edge during paper feeding.* *Feeding clear films may cause this error.
Remedy:	1 Change [Detect paper width] in printer menu to “Disable”.

Error code:	003130 201C
Description:	Sheet edge detection error during printing - cut sheet (support number: 1300)
Causes:	The paper width was changed +/-10mm or more at the home position side paper edge or away side paper edge during printing with border.* *The assumed situation is the folded paper during paper feeding.
Remedy:	1 Lift the lever up to remove the error, then reload or replace the paper

Error code:	003130 201D
Description:	Paper edge detection error during printing - roll paper (support number: 1300)
Causes:	The paper width was changed +/-10mm or more at the home position side paper edge or away side paper edge during printing with border.* *The assumed situation is the folded paper during paper feeding.
Remedy:	1 Lift the lever up to remove the error, then reload or replace the paper.

Error code:	004040 2019
Description:	Cut failure (support number: 4920) Memo: Job will be canceled when the error is removed.
Causes:	This error occurs in the following conditions. • Neither the number of cutter motor rotations nor rotation speed satisfy the specified rotation number and rotation speed during cutting. • The edge detection position is off +/-5mm or more from the reference position in edge detection after cutting.
Remedy:	1 • The cut paper is remaining on the ejection guide. => Remove the remaining paper. • The foreign substance around the ejection guide hits the cutter blade. => Remove the foreign substance. • The media is not used in the recommended use environment. => Use the media in the recommended environment..* • The paper in use does not support [Automatic cut]. => Select [User cut] for roll paper cut setting and cut the roll paper with scissors. • Replace the cutter blade, in the case other than above. *See the user manual for recommended use environment.

Error code:	100x
Description:	Low ink in the ink tank (support number: 1500, alarm code: -) Ink colors are identified with the last number of detail codes.
Causes:	The ink level detection pin in the ink tank is detected as inactive.
Remedy:	Prepare for ink tank replacement.

Error code:	1012
Display:	Problem with Printhead R Chk printing results
Description:	Printhead R non-ejection warning (doublehead model) (Check printout/ possible to continue printing) See 280C for detection criteria.
Causes:	The number of non-ejection nozzles is zero to 100 after recovery cleaning of non-ejection detection. In addition, the number of non-ejection complementary disabled nozzles is 30 or more.
Remedy:	1. Check image quality. (Unless there are problems with the image quality, there is no need to replace the printhead.) 2. Replace the printhead.

Error code:	1021
Display:	Papr Type Mismatch
Description:	RAM Error (Slot 1)

Error code:	1051
Display:	Paper Too Small
Description:	Paper mismatch (size) Size clip warning With [Warning Indication] selected for [Paper Mismatch Detection] in the menu settings, the size of paper loaded is smaller than that of specified from driver.
Causes:	Loading of smaller media into the printer than the media selected in the printer driver.
Remedy:	Continued printing allowed. Check driver settings. Replace with appropriate paper.

Error code:	1052
Display:	Borderless printng not possible. Check supported paper.
Description:	Borderless printing not available (unsupported size) With [Warning Indication] selected for [Paper Mismatch Detection] in the menu settings, borderless printing data is received, but roll paper not supporting borderless printing has been loaded.
Causes:	When the following conditions are satisfied. • [Detect paper setting mismatch] is set at other than “Pause”. • Loading of borderless printing unsupported media in borderless printing.
Remedy:	Replace with appropriate paper.

Error code:	1053
Display:	Paper position not suitable for borderless printing.
Description:	Borderless printing not available (physical) With [Warning Indication] selected for [Paper Mismatch Detection] in the menu settings, borderless printing data is received, but roll paper loaded is more than 1mm off the predefined position for the pre-ejection opening at the counter-HP side.
Causes:	When the following conditions are satisfied. • [Detect paper setting mismatch] is set at other than “Pause”. • The multi sensor detects that the paper edge at the home position side is not positioned within +/-3mm from the reference paper position when borderless printing is started.
Remedy:	Reload/ replace the roll paper.

Error code:	1054
Display:	PaprWidth Mismatch
Description:	Top Sensor/Media full sensor/Fixing Delivery Sensor PS204/205/915
Causes:	Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor

Error code:	1055
Description:	Power ON Jam 2
Causes:	Registration sensor/Fixing Delivery Sensor/Delivery Sensor
Remedy:	SR604/SR607/SR608 Registration Area to Cartridge Cartridge to Fixing Roller Area

Error code:	140x
Description:	Heater Temperature Error Temperature read by the Heater Temperature Sensor is abnormal (lower than -20C or higher than 200C). x = 1: Front heater. x = 2: Center Platen. x = 3: Rear Heater.
Causes:	At the timing when ink level detection pin of sub ink tank is OFF.
Remedy:	• Make sure that the failing Heater is connected correctly to the Main PCA. Make sure that the cables are not damaged. • Replace the failing Heater. • Replace the Main PCA.

Error code:	141x
Description:	Heater Error (High Temperature) Temperature read by the Heater Temperature Sensor is above 65C). x = 1: Front heater. x = 2: Center Platen. x = 3: Rear Heater.
Causes:	The tank cover is opened and ink tank is removed during printing.
Remedy:	• If the Printer is installed in a high temperature environment, move the Printer to an area where the operating temperature is much lower. • Make sure that the failing Heater is connected correctly to the Main PCA. Make sure that the cables are not damaged. • Replace the failing Heater. • Replace the Main PCA.

Error code:	1701
Description:	SGRaster general error: false number of parameters (support number: 3311/alarm code: -)
Causes:	The number of print data parameters is incorrect.
Remedy:	Check the print result. When using print program such as RIP (Raster Image Processor), ask the manufacturer of the print program.

Error code:	1702
Description:	SGRaster general error: omission of non-optional item (support number: 3312, alarm code: -)
Causes:	The omission prohibited parameter in the print data is omitted.
Remedy:	Check the print result. When using print program such as RIP (Raster Image Processor), ask the manufacturer of the print program.

Error code:	1703
Description:	SGRaster general error: unsupported data (support number: 3313, alarm code: -)
Causes:	The data out of setting range is set in the print data.
Remedy:	Check the print result. When using print program such as RIP (Raster Image Processor), ask the manufacturer of the print program.

Error code:	1706
Description:	SGRaster particular error: unsupported resolution value (support number: 3314, alarm code: -)
Causes:	The resolution setting in the print data is out of setting range.
Remedy:	Check the print result. When using print program such as RIP (Raster Image Processor), ask the manufacturer of the print program.

Error code:	1707
Description:	SGRaster particular error: unsupported pressure value (support number: 3315, alarm code: -)
Causes:	The compression method of the print data is inappropriate.
Remedy:	Check the print result. When using print program such as RIP (Raster Image Processor), ask the manufacturer of the print program.

Error code:	1708
Description:	SGRaster particular error: invalid format of data form (support number: 3316, alarm code: -)
Causes:	The format of print data form (color sequence, the number of bits) is inappropriate.
Remedy:	Check the print result. When using print program such as RIP (Raster Image Processor), ask the manufacturer of the print program.

Error code:	1709
Description:	SGRaster particular error: combination failure of resolution and image data format (support number: 3317, alarm code: -)
Causes:	The combination of print data resolution and image data format is inappropriate.
Remedy:	Check the print result. When using print program such as RIP (Raster Image Processor), ask the manufacturer of the print program.

Error code:	1900
Description:	Paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession.
Causes:	Defective PF main PWB. Device damage of EEPROM.
Remedy:	PF main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Error code:	1901
Description:	Fixing Delivery Delay Jam
Causes:	Fixing Delivery Sensor SR3
Remedy:	Pickup Cassette of the host machine

Error code:	1902
Description:	An abnormally high temperature of the PRE HEATERS(64) on the HEATER RELAY BOARD ASSY An abnormally high temperature of the PRE HEATERS(64) is detected.
Causes:	Unsupported JPEG format. The supported format is JPEG that complies with JFIF1.02.
Remedy:	Check whether the THERMISTOR, PRE(s) is correctly installed. Replace the HEATER RELAY BOARD ASSY .

Error code:	1903
Description:	An abnormally high temperature of the PLATEN HEATER(64) on the HEATER RELAY BOARD ASSY An abnormally high temperature of the PLATEN HEATER(64) is detected.
Causes:	Fixing Delivery Sensor SR3
Remedy:	Check whether the THERMISTOR, PLATEN(s) is correctly installed. Replace the HEATER RELAY BOARD ASSY .

Error code:	1904
Description:	An abnormally high temperature of the AFTER HEATER(64) on the HEATER RELAY BOARD ASSY An abnormally high temperature of the AFTER HEATER(64) is detected.
Causes:	The print setting in PDF file is set to "Not allowed to print".
Remedy:	Check whether the THERMISTOR, AFTER(s) is correctly installed. Replace the HEATER RELAY BOARD ASSY .

Error code:	1905
Description:	An abnormally low temperature of the PRE HEATERS(64) on the HEATER RELAY BOARD ASSY An abnormally low temperature of the PRE HEATERS(64) is detected.
Causes:	PDF file broken.
Remedy:	Check whether the PRE HEATERS(64) are properly connected. Check whether the THERMISTOR, PRE(s) is correctly installed. Check whether the THERMISTOR, PRE(s) is properly connected. Check whether the FUSE has blown. If so, replace the FUSE. Replace the HEATER RELAY BOARD ASSY .

Error code:	1906
Description:	An abnormally low temperature of the PLATEN HEATER(64) on the HEATER RELAY BOARD ASSY An abnormally low temperature of the PLATEN HEATER(64) is detected.
Causes:	Font substitution occurs because neither the font is set in the PDF file nor included in the installed font.
Remedy:	Check whether the PLATEN HEATER(s)(64) is properly connected. Check whether the THERMISTOR, PLATEN(s) is correctly installed. Check whether the THERMISTOR, PLATEN(s) is properly connected. Check whether the FUSE has blown. If so, replace the FUSE. Replace the HEATER RELAY BOARD ASSY .

Error code:	1907
Description:	An abnormally low temperature of the AFTER HEATER(64) on the HEATER RELAY BOARD ASSY An abnormally low temperature of the AFTER HEATER(64) is detected.
Causes:	Fixing Delivery Sensor SR3
Remedy:	Check whether the AFTER HEATER(s)(64) is properly connected. Check whether the THERMISTOR, AFTER(s) is correctly installed. Check whether the THERMISTOR, AFTER(s) is properly connected. Check whether the FUSE has blown. If so, replace the FUSE. Replace the HEATER RELAY BOARD ASSY .

Error code:	1908
Description:	An abnormal voltage of the heater on the HEATER CONT BOARD ASSY The voltage of the HEATER CONT BOARD ASSY is abnormally changed.d
Causes:	Fixing Delivery Sensor SR3
Remedy:	Replace the HEATER CONT BOARD ASSY . Replace the P/S BOARD ASSY .

Error code:	200C, 200D
Description:	Paper detection failure (support number: 1322, alarm code: -)
Causes:	The multi sensor fails to detect the paper frontside edge. • Assumed cause of this error is as follows: E The paper is loaded out of position. E The paper loaded is curling. E Due to taking out the cut paper just before printing, PAPER ENTRY SENSOR is not able to detect the cut paper.
Remedy:	Reload the paper. • When using clear film, Paper size may not be detected if ink is stained on the platen. In this case, open the top cover and clean the whole platen.

Error code:	200E, 200F
Description:	Paper size out of standard (support number: 1323, alarm code: -)
Causes:	The width or length of the paper in set is shorter than the supported smallest size. (200E) The width or length of the paper in set is longer than the supported largest size. (200F) • Detection timing is at paper width detection for roll papers, and paper width detection and paper length detection for cut sheets.
Remedy:	Lift the lever up to release the error, then feed the supported size paper.

Error code:	2010
Display:	Paper loaded askew. Press Load/Eject and reload the paper.
Description:	Main motor startup error Main motor is not stabilized within 1 s since the motor is activated.
Causes:	Main motor. Engine PWB
Remedy:	Main motor 1. To check the motor operation execute U030 Main (main motor). 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Main motor and Engine PWB (YC13) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the main motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB.

Error code:	2016
Display:	Paper jam. Press Load/Eject and reload the paper.
Description:	Jam while picking up, ejecting or printing on paper (A sequence of removing jams with the pinch roller released is required) Virtually all recovery errors that could occur in connection with paper pickup are handled.
Causes:	The length in feed direction of the cut paper detected by PAPER ENTRY SENSOR during printing is different from that of which detected during paper feeding.* *The change of the cut paper feed amount due to some reasons such as paper jam may cause this error.
Remedy:	1. Open and close the release lever to reload the paper. 2. Remove the paper once and then refeed it.

Error code:	2017
Display:	Paper size not detected. Lift the release lever and reload the paper.
Description:	Paper (right) side detection error 1. Multisensor error on light quantity adjustment 2. The read reference paper edge is 5 mm or more apart from its theoretical position. 3. Cannot locate the edge of reference paper.
Causes:	The multi sensor detected that the paper edge at home position side was off 5mm during paper feeding.* *Loading the paper being off the reference position may also cause this error.

Error code:	2018
Display:	Paper size not detected. Lift the release lever and reload the paper.
Description:	Paper (left) side detection error The non-reference edge of paper has been located by coarse detection but not by a second round of fine detection.
Causes:	The multi sensor failed to detect the away side paper edge during paper feeding.* *Feeding clear films may cause this error.

Error code:	2019
Display:	Cannot cut paper. Lift the release lever and reload the paper.
Description:	Cutting failure/jam detected due to a cutting failure An idle cutter unit or a cutter blade that is too blunt to cut sheet has been detected by the paper leading edge detection sequence. Or, cutter unit home position detection was failed.
Causes:	This error occurs in the following conditions. • Neither the number of cutter motor rotations nor rotation speed satisfy the specified rotation number and rotation speed during cutting. • The edge detection position is off +/-10mm or more from the reference position in edge detection after cutting.

Error code:	201C, 201D
Description:	Edge detection error during printing (support number: 1300, alarm code: -) • 201C for cut sheet, 201D for roll paper
Causes:	The paper width was changed +/-10mm or more at the home position side paper edge or away side paper edge during printing with border. • The assumed situation is the folded paper during paper feeding.
Remedy:	Lift the lever up to release the error, then reload or replace the paper.

Error code:	2020
Description:	Main drive motor starting time-out • The FG (Frequency generation) pulse does not reach the correct frequency since ASIC (U8) on the engine controller PWB (KP-992) has issued a motor activation signal to the main drive motor.r.
Causes:	Defective main drive motor. Excessive torque for driving drum unit or primary transfer unit. (Overloaded by a damaged gear.) Defective harness (2CK2711) between engine controller PWB (KP-992) and main drive motor, or poor contact of the connector terminals.
Remedy:	Replace the main drive motor. Check if the drum unit or primary transfer unit rotates smoothly. Check for broken gears. Replace if any. Check the continuity of the harness (2CK2711). Check the insertion of connectors.

Error code:	2025
Description:	Upper roll drive overload (at roll paper loading) (support number: 1328, alarm code: -)
Causes:	The electric current reached to the maximum loadable value at the upper ACTIVE ROLL BRAKE UNIT motor control in paper loading (between UPPER PAPER SET SENSOR and UPPER PAPER ENTRY SENSOR). <The assumed situation> • ACTIVE ROLL BRAKE UNIT receives load, e.g. due to touching the roll paper by the user, during roll paper front edge detection with UPPER PAPER SET SENSOR. • Heavy roll paper is being loaded.
Remedy:	Switch “Roll paper auto feed” setting in the operation panel to “Disable,” and feed the roll paper again. When re-feeding is disabled, feed the paper manually.

Error code:	2026
Description:	Lower roll drive overload (in roll paper loading) (support number: 1329, alarm code: -)
Causes:	The electric current reached to the maximum loadable value at the lower ACTIVE ROLL BRAKE UNIT motor control in paper loading (between LOWER PAPER SET SENSOR and LOWER PAPER ENTRY SENSOR). <The assumed situation> • ACTIVE ROLL BRAKE UNIT receives load, e.g. due to touching the roll paper by the user, during roll paper front edge detection with LOWER PAPER SET SENSOR. • Heavy roll paper is being loaded.
Remedy:	Switch “Roll paper auto feed” setting in the operation panel to “Disable,” and feed the roll paper again. When re-feeding is disabled, feed the paper manually.

Error code:	202B
Description:	Roll end error (due to strong adhesion) (support number: 1024, alarm code: -)
Causes:	During paper feeding, paper end detection error (the abnormal amount of rotation drive in ACTIVE ROLL BRAKE UNIT control) occurs due to strong adhesive on the roll end. . This error is assuming that the roll paper end cannot be peeled off from the roll core during paper feeding or printing, or paper feeding is disabled due to the weight of the roll paper.
Remedy:	The roll paper run out. => Replace the roll paper. The roll paper has been loaded but feeding does not work. => Change print mode and print (change the amount of paper feeding.) => Replace the roll paper with less amount of windings. (light weight roll paper) • Loose roll papers also can be the cause of this error. (Check if the roll paper is loose when this error occurs while the roll paper is remaining.)

Error code:	202C
Description:	Lower roll end error (strong adhesion) (support number: 1025, alarm code: -)
Causes:	During paper feeding from the lower roll unit, the end edge detection error (the abnormal amount of rotation drive in ACTIVE ROLL BRAKE UNIT control) of the roll paper occurs due to strong adhesive on the roll end. • <The assumed situation> The roll paper edge does not peel off from the roll core during paper feeding or printing, or paper feeding is disabled due to heaviness of the roll paper.
Remedy:	The roll paper run out. => Replace the roll paper. The roll paper has been loaded but feeding does not work. => Change print mode and print (change the amount of paper feeding.) => Replace the roll paper with the less amount of windings. (light weight roll paper) • Loose roll papers may also generates this error. (Check if the roll paper is loose when this error occurs while the roll paper is remaining.)

Error code:	2040
Description:	Borderless printing disabled in take-up mode - borderless printing unsupported paper (support number: 4118, alarm code: -)
Causes:	Loading of the borderless printing unsupported paper is detected when the printing starts, while the lower roll unit is taking up the paper.
Remedy:	Print with border or press “Cancel” to stop the printing.

Error code:	2041
Description:	Borderless printing disabled in take-up mode - paper edge detection error at home position side (operator error) (support number: 4119, alarm code: -)
Causes:	When the following condition is satisfied. • [Detect paper setting mismatch] is set at other than “Pause”. • Besides the lower roll unit is used for taking up the paper, the multi sensor detects that the paper edge at home position side is not positioned within +3mm from the reference position when the printing starts.* *<Assumed situation> When the paper is skewed during taking up, due to inappropriate fixing of the paper with taping to the take-up roll core put into the lower roll unit spool.
Remedy:	• Reload the roll paper if the skew is caused in the paper feed unit. • Put the tape and fix the roll paper on the take-up roll core again if the skew is caused in the take-up unit. • Select [Print with border] and continue printing.

Error code:	2042
Description:	Borderless printing disabled in take-up mode - receiving borderless printing unsupported data (support number: 4120, alarm code: -)
Causes:	The printer receives the data specifying the borderless printing unsupported paper types or unsupported paper width during the lower roll unit is taking up the paper.
Remedy:	Print with border or press “Cancel” to stop the printing.

Error code:	2043
Description:	Borderless printing disabled in take-up mode - three sides borderless prinitng is disabled (operator error) (support number: 4121, alarm code: -)
Causes:	When the following condition is satisfied. • [Detect paper setting mismatch] in the operation panel is set at “Hold job” or “Pause”. • The multi sensor detects that the paper feed position of the borderless printing supported paper is off +3mm or more from the tray for borderless printing at away position side (3mm or more from the default margin) when the printing starts.
Remedy:	Print with border or press “Cancel” to stop the printing.

Error code:	2044
Description:	Insufficient amount of remaining roll paper in take-up mode. (support number: 1021, alarm code: -)
Causes:	The lower roll unit is taking up the paper, [Manage remaining roll amount] is set at “Enable”, and the printer receives a print job that requires the longer paper size than the remaining paper length.
Remedy:	Print with the set paper, “Replace paper,” or press “Cancel” to stop the printing.

Error code:	2051
Description:	Unable to pick up the upper roll paper (in roll paper loading) (support number: 1326, alarm code: -)
Causes:	UPPER PAPER SET SENSOR fails to detect the roll paper front edge in roll paper feeding. <The assumed situation> • The front edge of the roll paper does not peel off from the roll paper. • The spool does not rotate due to gear damage in paper feeding. • Sensor malfunction.
Remedy:	Switch “Roll paper auto feed” setting in the operation panel to “Disable,” and feed the roll paper again. When re-feeding is disabled, feed the paper manually.

Error code:	2052
Description:	Unable to pick up the upper roll paper (in roll paper loading) (support number: 1300, alarm code: -)
Causes:	UPPER PAPER ENTRY SENSOR fails to detect the roll paper front edge within the specified time period after UPPER PAPER SET SENSOR detected the roll paper front edge.
Remedy:	Switch “Roll paper auto feed” setting in the operation panel to “Disable,” and feed the roll paper again. When re-feeding is disabled, feed the paper manually.

Error code:	2054
Description:	Unable to pick up the lower roll paper (in roll paper loading) (support number: 1327, alarm code: -)
Causes:	LOWER PAPER SET SENSOR fails to detect the roll paper front edge in roll paper feeding. <The assumed situation> • The front edge of the roll paper does not. • The spool does not rotate due to gear damage in paper feeding. • Sensor malfunction.
Remedy:	Switch “Roll paper auto feed” setting in the operation panel to “Disable,” and feed the roll paper again. When re-feeding is disabled, feed the paper manually.

Error code:	2055
Description:	Unable to pick up the lower roll paper (in roll paper loading) (support number: 1300, alarm code: -)
Causes:	LOWER PAPER ENTRY SENSOR fails to detect the roll paper front edge within the specified time period after LOWER PAPER SET SENSOR detected the roll paper front edge.
Remedy:	Switch “Roll paper auto feed” setting in the operation panel to “Disable,” and feed the roll paper again. When re-feeding is disabled, feed the paper manually.

Error code:	2056
Description:	Upper roll paper not loaded (support number: 1034, alarm code: -)
Causes:	UPPER PAPER SET SENSOR fails to detect loading of the roll paper in roll paper feeding.
Remedy:	Reload the roll paper.

Error code:	2057
Description:	Lower roll paper not loaded (support number: 1035, alarm code: -)
Causes:	LOWER PAPER SET SENSOR fails to detect loading of the roll paper in roll paper feeding.
Remedy:	Reload the roll paper.

Error code:	231x
Description:	Sub-ink tank ink filling failure (support number: 1757, alarm code: 0321 to 0333)
Causes:	In initial ink filling, or in ink filling to sub ink tank after replacing the ink tank, the ink level detection pin in the sub ink tank is not turned ON even after a certain time has passed from ink tank installation.
Remedy:	Remove and reinstall the ink tank, or replace the ink tank with other ink tanks. • Ink may not be flowing from the ink tank to the sub ink tank.

Error code:	2405
Display:	Borderless printng not possible. Lift the release lever and reload the paper. Online: Print
Description:	Invalid paper loading position (borderless printing) The position at which paper is loaded is unfit for borderless printing. Data with a borderless print specification has been received while the left or right edge of roll paper was off the center of the borderless print idle ejection port at the completion of roll paper pickup.
Causes:	Borderless printing is disabled due to the following reasons. The paper is loaded out of position. <When the printer driver is set at [Fit Roll Paper Width]> The multi sensor detects that the paper feed position of the borderless printing supported paper is off 3mm or more from paper edge at the home position side or from the tray for borderless printing at away position side. <When the printer driver is set at other than [Fit Roll Paper Width]> The multi sensor detects that the paper edge at the home position side is off 3mm or more from the reference position.
Remedy:	Reload the roll paper. Check spacers

Error code:	2406
Display:	Borderless printng not possible. Check paper size setting. Online: Print Load/Eject: Change Paper
Description:	Borderless print data not printable (logic) Borderless print data was received at the start of printing and one or more of the following requirements are met at the same time: -A feeder slot other than one for roll paper has been specified in the data. -A paper type that does not support borderless printing has been set on the data. -Banner printing has been specified on the data at the same time. -A paper size that does not support borderless printing has been specified in a job for which paper had already been fed.
Causes:	The borderless print data is received when printing starts. In addition, at least a condition among the following conditions is satisfied. • The paper feeding slot specified in the data is the slot other than roll paper feeding. • The print mode set in the data does not support borderless printing. • Banner printing is selected in the data at the same time. • [Fit Roll Paper Width] is specified and the paper size that does not support borderless printing is specified in the job. • The amount of extra printing for borderless printing in the data is out of standard.
Remedy:	Reset the driver and RIP.

Error code:	2407
Display:	Borderless printng not possible. Paper stretched or shrank. Confirm usage cond. of the paper.
Description:	It occurs when all of the following conditions are met at start of printing. -Borderless printing data has been received. -Roll paper has been loaded, and its paper width and edge position recognized at loading are within the supported range of borderless printing. -As a result of right/left side edge detection after start of print processing, it was detected as beyond the supported range of borderless printing.
Causes:	• The multi sensor detects that the paper edge at the home position side is not positioned within +3mm from the reference paper position. • The printer driver is set at [Fit Roll Paper Width]. Besides, the multi sensor detects that the paper edge at away position side is off 3mm or more from the tray for borderless printing during borderless printing.
Remedy:	Reset /replace the roll paper. Confirm and explain usage environment.

Error code:	2408
Display:	Borderless printng not possible. Check supported paper.
Description:	At the start of borderless printing, roll paper whose size doesn`t support borderless printing has been loaded.
Causes:	When the following condition is satisfied. • The printer driver is set at [Fit Roll Paper Width]. • The printer fed the roll paper in borderless printing unsupported size.
Remedy:	Replace with appropriate paper.

Error code:	2409
Display:	Paper position is not suitable for borderless printing. Check paper position. Print to normal printing. Stop printing.
Description:	Invalid paper loading position (suspended job/ borderless printing) All of the following conditions were met. -Borderless printing data has been received. -Roll paper whose paper loading position is not suitable for borderless printing has been loaded. -The right or left edge of roll paper is more than 1mm off the prescribed position of the pre-ejection opening.
Causes:	When restarting the hold job after replacing the paper with [Replace paper] button, the following cause may disable borderless printing.* • The loaded paper position is off the reference position. *What is “Hold Job?” When “Hold Job?” is selected at [Device settings > Paper-related settings > Detect paper setting mismatch] from the operation panel, the printer saves the printing jobs in HDD without performing printing. These saved jobs are called “Hold Job”.
Remedy:	Reload/ replace the roll paper. Check roll paper. 1) Select "Normal printing. (No borderless printing)" and enforce printing. Borderless print setting is ignored. Print with default margin. Default margin depends on selected feeding trays and media type. 2) Select "Stop printing" or press "stop button"to stop printing. 3) Select "replace printing" or release releasing lever.

Error code:	240A
Display:	Borderless printing is not possible. Check supported paper. Check paper position. Print to normal printing. Stop printing.
Description:	Borderless printing is not possible (suspended job/ unsupported size). All of the following conditions are met. -Borderless printing data has been received. -Roll paper not supporting borderless printing has been loaded.
Causes:	When restarting the hold job after replacing the paper with [Replace paper] button, the following cause may disable borderless printing. • The loaded paper is not in the borderless printing supported size.
Remedy:	Reload/ replace the roll paper. Check roll paper. 1) Select "Normal printing. (No borderless printing)" and enforce printing. Borderless print setting is ignored. Print with default margin. Default margin depends on selected feeding trays and media type. 2) Select "Stop printing" or press "stop button"to stop printing. 3) Select "replace printing" or release releasing lever.

Error code:	250x
Description:	Ink empty (support number: 1752, alarm code: 0301 to 0314)
Causes:	During printing or cleaning, remaining ink dot count reaches to the value of empty.
Remedy:	Replace the ink tank.

Error code:	252x
Description:	No ink tank (support number: 1660, alarm code: -)
Causes:	Ink tank is not detected when closing the tank cover.
Remedy:	Install the ink tank.

Error code:	254x
Description:	Ink tank ID error (support number: 168B, alarm code: 0111 to 0124)
Causes:	At the timing when the ink tank that does not support the corresponding product is installed.
Remedy:	Install the ink tank that supports the corresponding products.

Error code:	258x
Description:	Insufficient ink (support number: 1756, alarm code: -)
Causes:	Necessary ink amount is not left before cleaning.
Remedy:	Replace the ink tank.

Error code:	25Bx
Description:	Ink level detection pin OFF when the tank cover is open (support number: 1201, alarm code: -)
Causes:	Ink level detection pin turns off when the tank cover is open.
Remedy:	Close the tank cover. Check the remaining ink amount. When ink is not left, replace the ink tank.

Error code:	270x
Description:	Remaining ink amount unknown (genuine ink)(support number: 1730, alarm code: 0661 to 0793)
Causes:	The ink consumption amount used for status print, pattern adjustment printing, or print head cleaning exceeded the specified amount. • Refilling ink to the ink cartridge may cause this error.
Remedy:	Select [Cancel job] to remove the error temporarily or release [ink level detection].

Error code:	271x
Description:	Remaining ink amount unknown (non-genuine ink)(support number: 1731, alarm code: 0701 to 0853)
Causes:	Installation of the non-genuine ink tank.
Remedy:	Select [Cancel job] to remove the error temporarily or release [ink level detection].

Error code:	273x
Description:	Remaining ink amount unknown (no detection by ink level detection pin)(support number: 1753, alarm code: 0601 to 0613)
Causes:	Excess of the specified ink consumption amount in the ink cartridge during printing user`s data. • Refilling ink to the ink cartridge may cause this error.
Remedy:	Select [Cancel job] to remove the error temporarily or release [ink level detection].

Error code:	27Dx
Description:	Notification of new ink tank installation (support number: 1552, alarm code: -)
Causes:	The new ink tank installation is detected.
Remedy:	Press [OK] button to remove the error or the printer recovers when certain amount of time passed.

Error code:	27Ex
Description:	Notification of used ink tank installation (support number: 1551, alarm code: -)
Causes:	The used ink tank installation is detected.
Remedy:	Press [OK] button to remove the error or the printer recovers when certain amount of time passed.

Error code:	2800
Display:	No printhead Install printhead.
Description:	Printhead [X] non-existing [X]: Double-head model : The R-head does not exist. Single-head model: The head does not exit.
Causes:	The access cover is closed though no print head is detected.
Remedy:	1. Check the status of the printhead mounted. 2. Mount the long flexible cable and check the status of the cable being locked.

Error code:	2802
Display:	Printhead error Open top cover and replace the printhead.
Description:	Power ON JAM 1 (*2)
Causes:	TOP Sensor Residual
Remedy:	PS2 Cassette 1

Error code:	280D
Description:	Power ON JAM 1 (*2)
Causes:	Duplex Feed Sensor Residual
Remedy:	PS21 Duplex Feed Area

Error code:	2812
Display:	Right printhead error Open top cover and replace the right printhead.
Description:	Incompatible printhead R version
Causes:	Installation of inappropriate print head version.
Remedy:	Replace with a valid printhead. (An error has occurred but the printhead itself is not damaged, so communication has been maintained properly.)

Error code:	2816
Display:	Maintenance cartridge problem. Replace the maintenance cartridge.
Description:	Maintenance cartridge EEPROM error Communication is enabled but the information is corrupted. <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning.
Causes:	At maintenance cartridge EEPROM accessing, communication error occurs.
Remedy:	Replace the maintenance cartridge.

Error code:	2817
Display:	Maintenance cartridge problem. Replace the maintenance cartridge.
Description:	Maintenance cartridge ID error A maintenance cartridge for another model has been mounted. <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning.
Causes:	At maintenance cartridge EEPROM accessing, the maintenance cartridge that had been installed to the other model is detected.
Remedy:	Replace the maintenance cartridge. (The maintenance cartridge was capable of normal communication when the error occurred.)

Error code:	2818
Display:	No maintenance cartridge. Check the maintenance cartridge.
Description:	Maintenance cartridge not found Cannot communicate, or cannot detect a maintenance cartridge. <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning.
Causes:	No maintenance cartridge is detected.
Remedy:	Remove and reinstall, or replace the maintenance cartridge.

Error code:	2819
Display:	Maintenance cartridge full. Replace the maintenance cartridge.
Description:	Maintenance cartridge full Maintenance cartridge full is detected from the dot count and the usage period (drying time). <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning.
Causes:	At maintenance cartridge EEPROM accessing, the maintenance cartridge is detected to be full.
Remedy:	Replace the maintenance cartridge. Reference) The absorber may appear whitish or weigh light, depending on the usage conditions.

Error code:	281A
Display:	Prepare for maint cart replacement
Description:	Maintenance cartridge near-full (continued usage allowed) Near-full has been detected from the dot count and the usage period (drying time). <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning.
Causes:	At maintenance cartridge EEPROM accessing, the value indicates little capacity is left in the maintenance cartridge.
Remedy:	Prepare a maintenance cartridge.

Error code:	281B
Display:	No MaintenanceCartridge capacity. Replacethe maintenancecartridge.
Description:	The maintenance cartridge before cleaning does not have an enough capacity (reusable). Near-full has been detected from the dot count and the usage period (drying time). <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning.
Causes:	Insufficient capacity in the maintenance cartridge for cleaning is detected when accessing to the maintenance cartridge EEPROM.
Remedy:	Replace the maintenance cartridge. The maintenance cartridge can be put to reuse after the end of cleaning. Reference) The absorber may appear whitish or weigh light, depending on the usage conditions.

Error code:	2829
Description:	Multi sensor optical axis correction error (support number: 4923, alarm code: 0209)
Causes:	The corrected value exceeds the threshold during optical axis adjustment. • If the optical axis of multi sensor is off the correct position, paper end detection by the multi sensor results in incorrect detection. With measuring the difference between the theoretical printing position of optical correction pattern and the actual printing position, the multi sensor detects and corrects the value gap of the optical axis.
Remedy:	Check if the printed optical adjustment pattern has blur. If it is blurry, perform print head cleaning. If it is not blurry, check the multi sensor installation and perform “GAP CALIB” in service mode.

Error code:	2901
Display:	Mail box nearly full. Delete unwanted data. The mail box is nearly full. Delete
Description:	Delivery Delay Jam
Causes:	Fixing Delivery Sensor SR3
Remedy:	Pickup Cassette of the host machine

Error code:	2902
Display:	Mail box full. Now printing without saving data.
Description:	Power ON JAM 2 (*2)
Causes:	TOP Sensor Residual
Remedy:	PS2 Cassette 1

Error code:	2905
Display:	Mail box full. Delete unwanted data on your computer to resume printing. Press Stop to cancel printing. The mail box is full. Delete unwanted data from your computer to continue.
Description:	A job save has been executed when the available size of the permanent area of the hard disk space was lost. Cancel the job.
Causes:	The value indicates capacity is full in the hard disk.
Remedy:	Reorganize data.

Error code:	2906
Display:	Mail box full. Cannot save. Delete unwanted data on your computer to resume printing. Press Stop to cancel printing. Too many jobs for mail box. Delete unwanted data from your computer to continue.
Description:	The 101st job has been received when 100 jobs are already saved in the permanent area of the hard disk space.
Causes:	The number of files saved in the hard disk reaches the max.
Remedy:	Reorganize data.

Error code:	2907
Display:	Mail box full. Delete unwanted data. Maximum jobs stored. Delete unwanted data.
Description:	Delivery Delay Jam
Causes:	Fixing Delivery Sensor SR3
Remedy:	Registration to Drum Area

Error code:	2920
Display:	Media Take-up error. Check the paper. Press Online to clear error.
Description:	Cannot take up paper An error check has been made on paper after the paper had been fed 1850 mm, but the media take-up unit was not driven at all in that interval (up to about 3700 mm [when run immediately after the start of detection]).
Causes:	The paper feed amount by ACTIVE ROLL UNIT is insufficient against the paper feed amount by PAPER FEED MOTOR. (example: lack of torque, electrical failure of the motor, etc.)
Remedy:	1. Check to see if the media take-up unit is switched on with the lock lever down. 2. Check the connection between the main unit and the media take-up unit. 3. Check to see if the wait roller is properly set. 4. Check to see if the media take-up detection sensor is shielded by paper when it is presented. 5. Faulty media take-up detection sensor 6. Faulty Media take-up motor

Error code:	2921
Display:	Rewinding error. Check for jam at indicated position. Press Online to clear error. Rewinding error. Check for jam at indicated position.
Description:	Continued rewinding error The media take-up unit has continued rewinding for 10 seconds, with the media take-up paper detection sensor turned on, at printer power-on and at the start of printing.
Causes:	The paper feed amount by ACTIVE ROLL UNIT is too much against the paper feed amount by PAPER FEED MOTOR. (example: no paper, gear damage, out-of-control motor, etc.)
Remedy:	1. Check to see if any obstacle is placed at the media take-up paper detection sensor position. 2. Faulty media take-up paper detection sensor 3. Faulty media take-up button 4. Faulty media take-up motor

Error code:	2D03
Description:	Incomplete print head alignment (support number: 3000, alarm code: -)
Causes:	At the initial installation or at the incomplete print head position adjustment after the print head replacement. (including cancel)
Remedy:	Perform print head alignment.

Error code:	2D04
Description:	Print head alignment failure (support number: 4937, alarm code: -)
Causes:	The printer fails to adjust print head alignment toward the print head nozzle line direction.
Remedy:	Check the nozzle condition with the nozzle check pattern. Perform head cleaning if necessary. When the nozzle condition is not recovered by the nozzle cleaning, replace the print head.

Error code:	2E02
Display:	Sheet printing is selected. Press Load/Eject and load sheets.
Description:	Paper mismatch (cut sheet) No cassette paper has been loaded when data having a cut sheet specification is received.
Causes:	The cut sheet is not fed when receiving the job selecting cut sheet. Or “No sheets.” is detected after starting printing.
Remedy:	Load cut sheet.

Error code:	2E08
Display:	Wrong paper size. Check paper size setting on computer. Online: Print Stop: Stop Printing
Description:	Paper mismatch (size) (roll paper) The width of data and that of the actually loaded paper do not match.
Causes:	The paper roll width indicated in the print job and the roll paper width loaded on the printer are not matched.
Remedy:	Check the paper that is actually loaded on the printer and the paper size setting of the driver.

Error code:	2E09
Display:	Insufficient paper for job Online: Print Stop: Stop Printing Load/Eject: Change Paper
Description:	Short on roll paper All of the following conditions have been met at the start of printing: -[ON] has been selected for [Remaining Roll Paper Detection]. -Among the paper size settings coded in the print data, the paper length exceeds the remaining length of roll paper.
Causes:	The printer, which is selecting “Enable” at [Manage remaining roll amount], receives a print job that requires the longer paper size than the remaining paper length.
Remedy:	Replace the roll paper.

Error code:	2E0A
Display:	Roll printing is selected, but sheets are loaded. Press Load/Eject and remove the sheets.
Description:	Paper mismatch (roll paper) Print data having a roll paper print specification has been received at the completion of manual feed paper pickup.
Causes:	The printer receives roll paper print data while feeding has completed with cut sheet.
Remedy:	Check the paper that is actually loaded on the paper and the paper feed setting of the driver.

Error code:	2E0B
Display:	Cassette printing is selected. Press Load/Eject and remove manually loaded sheets.
Description:	Paper mismatch (cut sheet) Print data having a cassette print specification has been received at the completion of manual feed paper pickup.
Causes:	The printer receives cut sheet print data while feeding has completed with roll paper.
Remedy:	Check the paper that is actually loaded on the paper and the paper feed setting of the driver.

Error code:	2E0C
Display:	Manual printing is selected, but a roll is loaded. Press Load/Eject and remove the roll.
Description:	Paper mismatch (cut sheet) 1. Print data having a manual feed print specification has been received at the completion of roll paper pickup. 2. Print data having a manual feed print specification has been received when there is roll paper printout. 3. Cut sheet data has been received when the media take-up unit is in use.
Causes:	The printer receives the print data selecting cut sheet printing while take-up unit is in use.
Remedy:	Check the paper that is actually loaded on the paper and the paper feed setting of the driver.

Error code:	2E0D
Description:	Lower roll paper data received though upper roll paper is not yet ejected (support number: 4107, alarm code: 0433)
Causes:	The upper roll paper feeding has been completed, but the printed roll paper is still on the upper roll unit. In this state, the printer receives the print data that requires to select the lower roll paper setting. • Selecting gNoh or gPrint cut Guidelineh in [Automatic Cutting] setting for upper roll printing may cause this error.
Remedy:	Cut the printed paper and restart printing.

Error code:	2E0E
Display:	No Roll Feed Unit. Turn printer off and install roll feed unit.
Description:	Roll paper unit not installed The unit has received print data having a roll paper print specification when it had started without a roll unit being connected to it.
Causes:	The lower roll paper feeding has been completed, but the printed roll paper is still on the lower roll unit. In this state, the printer receives the print data that requires to select the upper roll paper setting. • Selecting gNoh or gPrint cut Guidelineh in [Automatic Cutting] setting for lower roll printing may cause this error.
Remedy:	1. Check the roll unit, and remove, install or replace the roll unit. 2. Check I/O mode (roll unit detection).

Error code:	2E0F
Display:	Top cover is open. Turn off printer, wait a while, and turn it on again.
Description:	The top cover is abnormally open.
Causes:	The purpose of the lower roll unit setting is other than paper feeding, when printing is commanded to the lower roll unit.
Remedy:	Check the cover. Check the sensor (I/O mode).

Error code:	2E15
Display:	Wrong paper feed slot for this paper type. Press Load/Eject and reload the paper.
Description:	Paper mismatch (type) A paper type that cannot be fed from the specified feeder slot has been specified.
Causes:	The media type selected in the job is different from the actual fed media.
Remedy:	Check the feeder slot/cassette pick-up setting.

Error code:	2E1B
Display:	The roll is empty. Load/Eject: Change Paper
Description:	No roll paper available (trailing edge of roll paper detected) -Trailing edge of paper has been detected by paper sensor in a roll paper operation. -LF out of synchronization on roll paper. (Detected the spool no longer rotating.)
Causes:	PAPER ENTRY SENSOR detects the paper end during feeding the roll paper.
Remedy:	1. Replace the roll paper. 2. Check paper sensor R (I/O mode). 3. Is the paper fed successfully (under a negative load or any other influence)?

Error code:	2E1C
Display:	Paper jam. Press Load/Eject and reload the paper.
Description:	Jam while ejecting paper (A sequence of removing jams with the pinch roller released is required) A jam has been detected while ejecting paper.
Causes:	LOWER PAPER ENTRY SENSOR detects the paper end during feeding the lower roll paper.
Remedy:	1. Open and close the release lever to reload the paper. 2. Remove the paper once

Error code:	2E20
Display:	Wrong paper type. Lift the release lever and reload the paper. Stop: Stop Printing
Description:	Paper mismatch (type) (on adjustment) The second and subsequent sheets of paper have been fed as a paper type different from the first sheet when LF adjustment was made from a cassette.
Causes:	When adjusting feeding system with cut sheets, page2 or after with different media type or size from that of page1 is fed, and appropriate adjustment is considered to be disabled.
Remedy:	Equalize the paper types for the first and second sheets with each other in adjustment printing.

Error code:	2E21
Display:	Hardware error. 03130000-2E21 Turn off printer, wait, then turn on again.
Description:	IEEE1394 interface error Any error has been detected while initializing IEEE1394 at startup.
Causes:	When adjusting the print head position with cut sheets, page2 or after with different media type or size from that of page1 is fed, and appropriate adjustment is considered to be disabled.
Remedy:	1. Restart the printer. 2. Remove and reinsert the IEEE1394 board and then restart the printer. 3. Replace the IEEE1394 board.

Error code:	2E30
Display:	The paper is too small.
Description:	Paper mismatch (size) With [Pause] selected for [Paper Mismatch Detection] in the menu setting, paper size for the paper loaded was smaller than the size specified by data.
Causes:	The paper width loaded on the printer is shorter than the paper width in print job.
Remedy:	Continued printing allowed. Check driver setting Replace with appropriate paper.

Error code:	2E31, 2E32
Description:	Insufficient roll paper left (2E31 = upper roll) (support number: 1022, alarm code: -) Insufficient roll paper left (2E32 = lower roll) (support number: 1023, alarm code: -)
Causes:	The printer, which is selecting gEnableh at [Manage remaining roll amount], receives a print job that requires the longer paper size than the remaining paper length. • When the lower roll unit has not been installed, this error appears. When the lower roll unit has been installed, the error 2E09 appears.
Remedy:	Select “Replace the paper and print” or press “cancel” to stop printing.

Error code:	2E33, 2E34
Description:	Roll paper not loaded (2E33 = upper roll) (support number: 100A, alarm code: -) Roll paper not loaded (2E34 = lower roll) (support number: 100B, alarm code: -)
Causes:	When receiving the roll paper selected print job, the roll paper (upper roll or lower roll) has not been fed. The upper roll nor lower roll has not been fed. In addition, the paper feeding slot is “Auto” in job setting.
Remedy:	Load the roll paper (the upper roll or the lower roll).

Error code:	2E38
Display:	Roll 2 (Lower) is selected. Press Load/Eject and load a roll.
Description:	Paper mismatch (roll paper)(Lower) No roll paper has been fed when a job with lower roll paper specification is received.
Causes:	In printing the printer internal data, the smaller paper than the size specified by each printing data is loaded.
Remedy:	Load roll paper.

Error code:	2E3A, 2E3B
Description:	Paper feeding failure (2E3A = upper roll) (support number: 1300, alarm code: -) Paper feeding failure (2E3B = lower roll) (support number: 1300, alarm code: -)
Causes:	PAPER ENTRY SENSOR fails to detect the paper edge at the proper timing during roll paper feeding.
Remedy:	Rewind all the paper manually, and reload the paper.

Error code:	2E3C
Display:	Paper jam. Lift the release lever.
Description:	During operations with cut sheet, the state of the paper detection sensor/ media sensor sensor has become invalid.
Causes:	PAPER ENTRY SENSOR detects no paper loaded on the printer when the printing starts.
Remedy:	Reload the paper.

Error code:	2E3D, 2E3E
Description:	Paper feeding failure (2E3D = upper roll) (support number: 1300, alarm code: -) Paper feeding failure (2E3E = lower roll) (support number: 1300, alarm code: -)
Causes:	When the paper passes PAPER ENTRY SENSOR, the multi sensor fails to detect the paper edge. • This error occurs when the LF roller is catching the paper.
Remedy:	Lift the release lever up, and reload the cut sheet.

Error code:	2E3F
Display:	Paper jam. Lift the release lever.
Description:	When either upper or lower roll paper is in operation, the states of the roll paper detection sensor, roll feeding sensor, and paper detection sensor/ media sensor sensor became invalid.
Causes:	Paper jam other than the above Detail Codes (2E3A to 2E3E).
Remedy:	Reload the paper.

Error code:	2E40, 2E41
Description:	Roll paper not loaded (2E40 = upper roll) (support number: 100A, alarm code: -)Roll paper not loaded (2E40 = lower roll) (support number: 100B, alarm code: -)
Causes:	After starting printing, “No roll sheets” (at upper roll or lower roll) is detected.
Remedy:	Load the roll paper at the upper or lower roll unit.

Error code:	2E42
Display:	MediaType Mismatch
Description:	Paper mismatch (type/ restart printing of suspended job) It occurs when all of the following conditions are met: -[Stop] selected for [Paper Mismatch Detection] in menu settings. -[Change Paper] button was pressed for suspended jobs from host. -The paper type that has been set in the job and the type of actually fed paper do not match.
Causes:	The size of the paper selected in the held job is different from the actual fed paper.
Remedy:	Continued printing allowed. Replace with appropriate paper.

Error code:	2E43
Description:	Media type unknown (support number: 4111, alarm code: -)
Causes:	The job is selecting an unregistered media type in the printer. • This error occurs under the following situation. 1. A print job that required a paper type which had been registered in the printer at some point of time was saved in the HDD. After that, this media type was deleted from the printer by MCT. However, this job was executed. 2. When printing from driver, media type data is not obtained from the printer until pressing gGet Information...h button. After deleting a media type from MCT, executing a print job that specifies this deleted media, without pressing gGet Information...h button, may generate this error.
Remedy:	Check the media type settings and print again.

Error code:	2E45
Display:	MediaType Mismatch
Description:	Paper mismatch (type/ restart printing of suspended job) It occurs when all of the following conditions are met: -[Stop] selected for [Paper Mismatch Detection] in menu settings. -The paper width that has been set with data and the paper width of actually fed paper do not match.
Causes:	The width of the roll paper selected in the held job is different from the width of actual fed roll paper.
Remedy:	Continued printing allowed. Check the driver settings. Replace with appropriate paper.

Error code:	2E75
Description:	Borderless printing (or three sides borderless printing) is disabled (operator error) (support number: 4113, alarm code: -)
Causes:	When the following condition is satisfied. • [Detect paper setting mismatch] in the operation panel is set at “Hold job” or “Pause”. • The printer driver is not set at [Fit Roll Paper Width]. • The multi sensor detects that the paper feed position is off +3mm or more from the tray for borderless printing at away position side when the printing starts.
Remedy:	• Select [Fit Roll Paper Width] for the printer driver setting. • Suspend the printing. Switch to [Print with border] and print again. • Replace the paper and print again.

Error code:	2EA1, 2EA2
Description:	Spool detection error in the upper ACTIVE ROLL BRAKE UNIT calibration (Detail Code: 2EA1, support number: 1018, alarm code: -) Spool detection error in the lower ACTIVE ROLL BRAKE UNIT calibration (Detail Code: 2EA2, support number: 1019, alarm code: 0521)
Causes:	At the timing when the spool is detected in ACTIVE ROLL BRAKE UNIT calibration.
Remedy:	Remove the spool installed in the printer.

Error code:	2EA3
Description:	Print head alignment unavailable for the media (support number: 4932, alarm code: 0100)
Causes:	The media for films which has too high transparency to adjust the print head position is loaded.
Remedy:	When a highly transparent film media* is loaded, replace the media. *Tracing paper, semi-transparent matte film, Clear Films, etc.

Error code:	2EA4
Description:	Blur printing of the print head alignment pattern (support number: 4934, alarm code: 0102)
Causes:	Print blur occurs when the density at the pattern edge is lower than prescribed value.
Remedy:	Check the print out by nozzle check. Perform cleaning as required. When the problem is not removed, replace the print head.

Error code:	2EA5
Description:	Insufficient contrast in the print head alignment pattern (support number: 4933, alarm code: 0101)
Causes:	The difference of the density in the pattern is lower than the prescribed value.
Remedy:	Check the print out by nozzle check. Perform cleaning as required. When the problem is not removed, replace the print head.

Error code:	2EA6
Description:	Abnormal print head alignment value (support number: 4935, alarm code: 0103)
Causes:	The print head alignment value is higher than the prescribed value.
Remedy:	Check the print out by nozzle check. Perform cleaning as required. When the problem is not removed, replace the print head.

Error code:	2EA7
Description:	Hard disk format abnormal (support number: 4901, alarm code: 0524)
Causes:	The hard disk format type is different.
Remedy:	Format the hard disk.

Error code:	2EA8
Description:	Automatic feeding adjustment error (support number: 4931, alarm code: 0206)
Causes:	Unreadable patches are six or more.
Remedy:	Check if smudge is on the pattern print sheet. Check if the environment is where the natural light comes in. Perform cleaning of the print head.

Error code:	2EA9
Description:	Eccentricity adjustment error (support number: 4936, alarm code: 0207)
Causes:	Eccentricity automatic adjustment value is out of the prescribed value.
Remedy:	Check if smudge is on the pattern print sheet. Check if the environment is where the natural light comes in. Perform cleaning of the print head.

Error code:	2EAA
Description:	Automatic feeding adjustment failure (support number: 4929, alarm code: 0211)
Causes:	In processing of automatic judgement for uneven paper feeding, multi sensor read value is out of the prescribed value.
Remedy:	Check if smudge is on the pattern print sheet. Check if the environment is where the natural light comes in. Perform cleaning of the print head.

Error code:	2EAB
Description:	Failure in automatic judgment of uneven printing in the carriage moving direction (support number: 4928, alarm code: 0278)
Causes:	In processing of automatic judgement for uneven printing toward carriage scanning direction, multi sensor read value is out of the prescribed value.
Remedy:	Check the print out by nozzle check. Perform cleaning the print head as required. When the problem is not removed, replace the print head.

Error code:	2EBC
Description:	Carriage cogging correction failure (support number: 4930, alarm code: 0215)
Causes:	In the automatic judgement for carriage cogging adjustment process, the measured value is out of the specified range. • The detecting timing of carriage cogging adjustment is as follows. E After print head replacement. E After print head alignment adjustment. E After carriage related errors.
Remedy:	• Check if the linear scale is attached properly. Make sure that the linear scale is free from any scratch or dirt. • If the linear scale is in appropriate condition, replace the carriage encoder sensor.

Error code:	2F6A
Display:	Hardware error 038A0002-2F6A Turn off printer, wait a while, then turn it on again.
Description:	Firmware update failed.
Causes:	The print head which had been installed into a different model before was installed.
Remedy:	1. Update firmware again 2. Replace the spectrophotometer unit PCB.

Error code:	2F6B
Display:	Hardware error 038A0002-2F6B Turn off printer, wait a while, then turn it on again.
Description:	Initialization after power on of CPU at spectrophotometer unit side failed.
Causes:	The print head which had been installed into the model that used a different ink set before was installed. • This error occurs in service mode only.
Remedy:	Replace the spectrophotometer unit PCB.

Error code:	2F7C
Description:	Print head contact error at print head replacement (support number: 140B , alarm code: -)
Causes:	Despite of print head installation, the print head is not recognized.
Remedy:	Reinstall the print head. When the problem is not removed, replace the print head.

Error code:	3000
Description:	Main Motor`s failure to turn • The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning.
Causes:	The AC power has been shut off due to a power failure, unplugged, PSH BOARD failure, or MAIN BOARD failure or the like.
Remedy:	1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the PWB-M connector for proper connection and correct as necessary. 4 M1 operation check PWB-M CNDM1-5 (REM) PWB-M CNDM1-8 (LOCK) K to L-2. 5 Change PWB-M. 6 Change PU1.

Error code:	3001
Description:	Door Open JAM 1 (*1)
Causes:	TOP Sensor Residual
Remedy:	PS2 Multi-purpose Tray

Error code:	3002
Description:	A damaged cluster was found on the HDD.
Causes:	The damaged cluster is automatically marked as “bad”. If this error is frequent, format the HDD.
Remedy:	PS2 Cassette 1

Error code:	3003
Description:	Door Open JAM 1 (*1)
Causes:	TOP Sensor Residual
Remedy:	PS2 Cassette 2

Error code:	3004
Description:	Other WPS errors (support number: 4950, alarm code: -)
Causes:	The failure of the reasons other than above WPS.
Remedy:	Follow the message on the operation panel. (Check the setting and reset.)

Error code:	3005
Description:	AOSS multiple access points error (support number: 4951, alarm code: -)
Causes:	Multiple wireless LAN routers in AOSS mode are detected.
Remedy:	Follow the message on the operation panel. (Check the setting and reset.)

Error code:	3006
Description:	AOSS timeout (support number: 4951, alarm code: -)
Causes:	Wireless LAN router in AOSS mode is not detected.
Remedy:	Follow the message on the operation panel. (Check the setting and reset.)

Error code:	3007
Description:	Door Open JAM 1 (*1)
Causes:	TOP Sensor Residual
Remedy:	PS2 Registration Area to Drum Area

Error code:	3008
Description:	Dooe Open JAM 1 (*1)
Causes:	Fixing Delivery Sensor Residual
Remedy:	PS13 Drum Area to Fixing Area

Error code:	3009
Description:	Dooe Open JAM 1 (*1)
Causes:	Delivery Tray Full Sensor Residual
Remedy:	PS4 Fixing Area to Delivery Area

Error code:	3010
Description:	Access point connection failure (support number: 4952, alarm code: -)
Causes:	Connecting to the access point by setting wireless LAN manually fails.
Remedy:	Follow the message on the operation panel. (Check the setting and reset.)

Error code:	3011
Description:	Access point not detected with the specified SSID (support number: 4952, alarm code: -)
Causes:	In set-up, AP detection of the input SSID fails.
Remedy:	Follow the message on the operation panel. (Check the setting and reset.)

Error code:	3012
Description:	Connection alarm due to IP address obtaining failure (support number: 4953, alarm code: -)
Causes:	In wireless detail setting, despite selecting [WEP], obtaining IP address fails, and AutoIP is set.
Remedy:	Follow the message on the operation panel. (Check the setting and reset.)

Error code:	3013
Description:	Cableless setup timeout (support number: 4954, alarm code: -)
Causes:	In cableless set-up, wireless LAN setting process was finished in error due to timeout.
Remedy:	Follow the message on the operation panel. (Check the setting and reset.)

Error code:	3014
Description:	Cableless setup setting failure (support number: 4954, alarm code: -)
Causes:	In cableless set-up, wireless LAN setting fails.
Remedy:	Follow the message on the operation panel. (Check the setting and reset.)

Error code:	3015
Description:	LAN invalid in IPv4/IPv6 setting (support number: 4955, alarm code: -)
Causes:	LAN is invalid when IPv4/IPv6 is selected.
Remedy:	“Enable” [Active wired LAN] or [Active wireless LAN].

Error code:	3016
Description:	LAN setting unavailable (support number: 4956, alarm code: -)
Causes:	When changing LAN setting, the setting change was not available due to the following reasons. • The printer is in the middle of operation. • Remote UI is selecting the printer settings.
Remedy:	Terminate other operations and select settings again.

Error code:	3017
Description:	[Raku Raku WLAN Start] timeout error (support number: 4957, alarm code: -)
Causes:	Connecting via [Raku Raku WLAN] fails.
Remedy:	Follow the message on the operation panel.

Error code:	3018
Description:	[Raku Raku WLAN Start] other errors (support number: 4957, alarm code: -)
Causes:	The wireless LAN router in Raku Raku wireless mode is not detected.
Remedy:	Follow the message on the operation panel.

Error code:	3022
Description:	Wi-Fi Direct connection request (support number: 4959, alarm code: -)
Causes:	Connection is requested from Wi-Fi Direct supported device.
Remedy:	Select “Yes (accept)” or “No (not accept).”

Error code:	3023
Description:	SMTP server setting error (support number: 3414, alarm code: -)
Causes:	Connecting to SMTP server fails.
Remedy:	Check with the remote UI if the address and port number of the mail server for outgoing message (SMTP) in the mail server settings are correct.

Error code:	3024
Description:	POP server setting error (support number: 3415, alarm code: -)
Causes:	Connecting to POP server fails.
Remedy:	Check with the remote UI if the address and port number of the mail server for incoming message (POP3) in the mail server settings are correct.

Error code:	3025
Description:	SMTP SSL connection error (support number: 3416, alarm code: -)
Causes:	Connecting SMTP server with SSL fails.
Remedy:	Check with the remote UI if the secure connection (SSL) settings of the mail server and the printer are matching.

Error code:	3026
Description:	POP SSL connection error (support number: 3417, alarm code: -)
Causes:	Connecting POP server with SSL fails.
Remedy:	Check with the remote UI if the secure connection (SSL) settings of the mail server and the printer are matching.

Error code:	3027
Description:	SMTP command error (support number: 3418, alarm code: -)
Causes:	Sending command to SMTP server fails.
Remedy:	Check with the remote UI if the items related to the mail server for outgoing message (SMTP) in the mail server settings are correct.

Error code:	3028
Description:	SMTP authorization error (support number: 3419, alarm code: -)
Causes:	SMTP authorization user name is not specified, SMTP authorization password is not specified, or SMTP authorization fails.
Remedy:	Check with the remote UI if the account and the password for outgoing message in the mail server settings are correct.

Error code:	3029
Description:	POP command error (support number: 3420, alarm code: -)
Causes:	Sending command to POP server fails.
Remedy:	Check with the remote UI if the items related to the mail server for incoming message (POP3) in the mail server settings are correct.

Error code:	3030
Description:	POP authorization error (support number: 3421, alarm code: -)
Causes:	POP authorization user name is not specified, POP authorization password is not specified, or POP authorization fails.
Remedy:	Check with the remote UI if the account and the password for incoming message in the mail server settings are correct.

Error code:	3031
Description:	APOP authorization error (support number: 3422, alarm code: -)
Causes:	APOP authorization fails.
Remedy:	Check with the remote UI if the APOP settings are appropriate.

Error code:	3032
Description:	Socket server connection error (support number: 3423, alarm code: -)
Causes:	Communication timeout occurs in connecting with SMTP server. Or Read/Write socket error occurs.
Remedy:	Check with the remote UI if the mail server settings are appropriate.

Error code:	3033
Description:	Destination mail address error (support number: 3424, alarm code: -)
Causes:	Destination mail address is incorrect.
Remedy:	Select a correct e-mail address of destination with the remote UI and send again.

Error code:	3034
Description:	Unsupported device connected (support number: 2001, alarm code: -)
Causes:	USB host unsupported device is connected.
Remedy:	Follow the message on the operation panel. • The only device that can print directly by connecting to this machine is USB flash memory.

Error code:	3035
Description:	Hub not supported (support number: 2002, alarm code: -)
Causes:	USB hub is connected to USB host. • Connecting USB flash memory via USB hub is not supported.
Remedy:	Follow the message on the operation panel. (Check the setting and reset.)

Error code:	311111 2E3B
Description:	Paper feeding failure (lower roll) (support number: 1300)
Causes:	Feeding of the roll paper fails at the lower roll paper path (roll2). (from the paper feed sensor to the PE sensor in paper path)
Remedy:	1 Reload the roll paper. (Remove left paper pieces and check the top edge of the paper.) The error is removed Complete. The error is not removed Go to 2. 2 Replace the following parts from the top and check if the error is removed after each replacement. • ROLL PAPER FEED SENSOR UNIT. • HARNESS ASS’Y, RLNIP PF SNS. • PAPER ENTRY SENSOR. • DRIVE NIP ARM UNIT. • ACTIVE ROLL BRAKE UNIT. Adjustment and counter reset is necessary. 3 Check other suspected cause. • Media related cause (size, media type mismatch, paper turn-up at the top edge) • Curly end edge of the roll paper • Avoid the paper with strong stiffness or heavy roll paper.

Error code:	311112 2E3E
Description:	Paper feeding failure (lower roll) (support number: 1300)
Causes:	Feeding of the roll paper fails at the lower roll paper path (roll2). (from the PE sensor to end of feeding in paper path)
Remedy:	1 Release the release lever. Reload the paper. (Remove left paper pieces and check the top edge of the paper.) The error is removed Complete. The error is not removed Go to 2. 2 Replace the following parts from the top and check if the error is removed after each replacement. • ROLL PAPER FEED SENSOR UNIT. • HARNESS ASS’Y, RLNIP PF SNS. • PAPER ENTRY SENSOR. • DRIVE NIP ARM UNIT. • MULTI SENSOR UNIT. Adjustment and counter reset is necessary. • ACTIVE ROLL BRAKE UNIT. Adjustment and counter reset is necessary. 3 Check other suspected cause. • Media related cause (size, media type mismatch, paper turn-up at the top edge) • Curly end edge of the roll paper • Avoid the paper with strong stiffness or heavy roll paper.

Error code:	311113 2054
Description:	Unable to pick up the lower roll paper (in roll paper loading) (support number: 1327)
Causes:	LOWER PAPER SET SENSOR fails to detect the roll paper front edge in roll paper feeding. <The assumed situation> • The front edge of the roll paper does not peel off from the roll paper. • The spool does not rotate due to gear damage in paper feeding. • Sensor malfunction.
Remedy:	1 Feed the roll paper again. When re-feeding is disabled, feed the paper manually.

Error code:	311113 2055
Description:	Unable to pick up the lower roll paper (in roll paper loading) (support number: 1300)
Causes:	LOWER PAPER ENTRY SENSOR fails to detect the roll paper front edge within the specified time period after LOWER PAPER SET SENSOR detected the roll paper front edge.
Remedy:	1 Feed the roll paper again. When re-feeding is disabled, feed the paper manually.

Error code:	311113 2057
Description:	Lower roll paper not loaded (support number: 1035)
Causes:	LOWER PAPER SET SENSOR fails to detect loading of the roll paper in roll paper feeding.
Remedy:	1 Reload the roll paper.

Error code:	315150 2921
Description:	Take-up error (support number: 4922)
Causes:	Take-up error (nonstop take-up) of the roll paper occurs at paper take-up part of the lower roll unit.
Remedy:	1 Check the tape on the roll paper core. The tape is pasted. Go to 2. The tape is not pasted Paste the tape on the roll paper core and press [OK]. 2 Replace the following parts from the top and check if the error is removed after each replacement. The roll holder set. • ACTIVE ROLL BRAKE UNIT. Adjustment and counter reset is necessary. • SPOOL LOCK UNIT and COVER, ROLL GEAR L.

Error code:	315250 2920
Description:	Take-up error (support number: 4922)
Causes:	Take-up error (take-up disabled) of the roll paper occurs at paper take-up part of the lower roll unit.
Remedy:	1 Check if paper jam is occurred. Not jammed Go to 2. Paper is jammed Remove the paper jam and press [OK.] 2 Replace the following parts from the top and check if the error is removed after each replacement. • The roll holder set. • ACTIVE ROLL BRAKE UNIT. Adjustment and counter reset is necessary. • SPOOL LOCK UNIT and COVER, ROLL GEAR L.

Error code:	3200
Description:	Exposure lamp error When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s.
Causes:	Defective connector cable or poor contact in the connector. Defective LED lamp PWB. Defective ISC PWB. Defective main PWB.
Remedy:	Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and main PWB (YC11) Defective LED lamp PWB. Replace the LED lamp PWB and check for correct operation. Defective ISC PWB. Replace the ISC PWB and check for correct operation. Defective CCD PWB. Replace the ISU and check for correct operation. Defective main PWB. Replace the main PWB and check for correct operation.

Error code:	3201
Description:	Fusing motor malfunction The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary.
Causes:	• Fusing motor (M2) • Printer control board (PRCB)
Remedy:	1 Check the connector between M2-PRCB CN9 for proper connection and correct as necessary. - - 2 Check the loading status of the fusing unit drive, and correct the error as necessary. - - 3 M2 operation check PRCB CN9-9 to 12 15-C 4 Replace M2 - - 5 PRCB F9 conduction check - - 6 Replace PRCB

Error code:	3305
Description:	Media update corruption (support number: 3306, alarm code: 0520)
Causes:	Recognizing the media data properly fails due to the broken media data of the printer.
Remedy:	Start up [Media Configuration Tool] and recover the printer media data.

Error code:	EC01 2F90
Description:	Carriage overload (support number: 4801)
Causes:	The motor keeps 100% output. In addition, CARRIAGE UNIT scans more than a constant length.
Remedy:	1 Check stain on the carriage shaft. No stain Go to 2. Stain adheres Perform cleaning of the shaft. 2 Perform [DIAGNOSIS > CR SYSTEM CHECK] to diagnose carriage system. No problem Replace CARRIAGE MOTOR. Failure in LONG FFC CHECK Replace CARRIAGE UNIT.

Error code:	EC01 2F95
Description:	Carriage drive timeout (support number: 4801)
Causes:	CARRIAGE UNIT does not finish driving within the scheduled time.
Remedy:	1 Check the items below. a) Stain on the carriage shaft. b) Cable connection of the carriage motor. c) Looseness and abrasion of BELT, CARRIAGE. Appropriate Go to 2. Inappropriate a) Perform cleaning of the shaft. b) Connect the cable. c) Replace BELT, CARRIAGE. 2 Perform [DIAGNOSIS > CR SYSTEM CHECK] to diagnose carriage system. No problem Replace CARRIAGE MOTOR. Failure in LONG FFC CHECK Replace CARRIAGE UNIT.

Error code:	EC02 2F42
Description:	Complete non-ejection in one line of nozzles (support number: 1492)
Causes:	A complete non-ejection nozzle line in one of two print head nozzle lines of a color.
Remedy:	1 When the printer does not recover with restarting, check if the ink is filling into tubes. Ink is filled Go to 2. (Insufficient ink in the print head or print head defect is suspected.) Ink is not filled Replace INK TUBE UNIT. 2 Perform [DIAGNOSIS > HEAD CNT CHECK] and check the condition of print head contacting part. Proper condition Go to 3. Abnormal condition Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) 3 Perform deep cleaning and print nozzle check pattern. Proper nozzle pattern Complete. Improper nozzle pattern Replace the print head.

Error code:	EC03 403A
Description:	Printer VH recognition failure (support number: B20A) Memo: Remove the error in service mode when handling is completed.
Causes:	The printer cannot confirm VH output.
Remedy:	1 Check the connection of flexible cables on MAIN PCB UNIT. If the connection is proper, replace CARRIAGE UNIT.

Error code:	EC03 4061
Description:	Carriage unit for wrong model installed (support number: 5106) Memo: Remove the error in service mode when handling is completed.
Causes:	The CARRIAGE UNIT for a different printer model is connected.
Remedy:	1 Check the connection of FLEXIBLE CABLE. Proper connection Go to 2. Improper connection Connect FLEXIBLE CABLE again. 2 Replace the CARRIAGE UNIT. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC04 2F31
Description:	Accuracy error of carriage parking position in non-ejection detection (support number: 4801)
Causes:	The parked position of the carriage is slightly off when performing non-ejection detection or adjusting the head management sensor position.
Remedy:	1 Check the items below. a) Installation, scratch, and stain on SCALE, LINEAR. b) Stain on the carriage shaft. Fine condition Go to 2. Installation failure, scratch, or stain is found a) Perform cleaning or replace SCALE, LINEAR. b) Perform cleaning of shaft. 2 Replace INK TUBE UNIT. The problem is resolved Complete. The problem is not resolved Replace CARRIAGE UNIT.

Error code:	EC04 2F91
Description:	Carriage encoder error (support number: 4801)
Causes:	When detected value of acceleration sensor exceeds the threshold. In addition, it is in the CARRIAGE UNIT scanning direction.
Remedy:	1 Check the items below. a) Installation, scratch, and stain on FILM, TIMING SLIT STRIP. b) Connection of FLEXIBLE CABLE UNIT. (When the error occurs after connecting and disconnecting the cable) Appropriate Go to 2. Inappropriate a) Perform cleaning or replace FILM, TIMING SLIT STRIP. b) Connect FLEXIBLE CABLE UNIT again. 2 Replace CARRIAGE ENCODER UNIT. The problem is resolved Complete. The problem is not resolved Replace FLEXIBLE CABLE UNIT.

Error code:	EC05 2F92
Description:	Carriage movement disabled (support number: 4801)
Causes:	The motor keeps 100% output. In addition, CARRIAGE UNIT stops less than a constant scanning length.
Remedy:	1 Check the items below. a) Cable connection of the carriage motor. b) Looseness and abrasion of BELT, CARRIAGE. c) Obstacle. d) The position of SCALE, LINEAR. Appropriate without any obstacle Go to 2. Inappropriate or obstacles are blocking a) Connect the cable. b) Replace BELT, CARRIAGE. c) Remove the obstacle. d) Attach it at the correct position. 2 Replace CARRIAGE MOTOR. The problem is resolved Complete. The problem is not resolved Replace CARRIAGE UNIT.

Error code:	EC06 2F9A
Description:	Carriage lift motor error (support number: 4801)
Causes:	Overload on the lift motor.
Remedy:	1 Check the items below. a) Cable connection of LIFT MOTOR. b) Couple CARRIAGE UNIT with the coupling part, turn the gear of LIFT UNIT manually and check if excessive load is applied. Appropriate Replace CARRIAGE UNIT. Inappropriate Go to 2. Not coupled with the coupling part Coupled with the coupling part 2 Check any damages of the gears for driving LIFT UNIT. No damage found Replace LIFT MOTOR. The damage found Replace the damaged gear.

Error code:	EC06 2F9B
Description:	Carriage lift sensor error (support number: 4801)
Causes:	Although the lift motor is rotating and generating larger torque than the certain amount, CARRIAGE LIFT SENSOR cannot detect ON/OFF.
Remedy:	1 Check the items below. a) Cable connection of CARRIAGE LIFT SENSOR. b) Execute [DIAGNOSIS > I/O DISPLAY] and check the CARRIAGE LIFT SENSOR operation. Appropriate Replace CARRIAGE UNIT. Inappropriate Go to 2. 2 Check any damages of the gears around LIFT MOTOR. No damage found Replace LIFT MOTOR. The damage found Replace the damaged gear.

Error code:	EC06 2F9C
Description:	Carriage docking error (support number: 4801)
Causes:	- Although the lift motor is rotating, generated torque is smaller than a constant value. In addition, CARRIAGE LIFT SENSOR cannot detect ON/OFF. - CARRIAGE UNIT does not move to the home position during detecting home position.
Remedy:	1 Check the items below. a) Check if CARRIAGE UNIT is coupled with the coupling part when the error occurs. b) If CARRIAGE UNIT is coupled with the coupling part , check if the coupling part is damaged. Appropriate Go to EC05-2F92 error. Inappropriate a) Go to EC05-2F92 error. b) When the coupling at the lift unit side is damaged Replace COUPLING, CR LIFT DRIVE. When the coupling at CARRIAGE UNIT side is damaged Replace CARRIAGE UNIT. Not coupled with the coupling part Coupled with the coupling part

Error code:	EC07 2F19
Description:	Carriage acceleration sensor error (support number: 4801)
Causes:	Access to acceleration sensor is disabled.
Remedy:	1 Perform [DIAGNOSIS > CR_SYSTEM_CHECK] to diagnose carriage system. Failure in ACC. SENSOR CHECK or CR VIBRATIONCHECK Replace CARRIAGE UNIT. Failure in LONG FFC CHECK Replace FLEXIBLE CABLE UNIT. * If the error occurred after reseating the flexible cables, check the condition of flexible cables` connection.

Error code:	EC07 4060
Description:	Carriage EEPROM error (support number: 6820) Memo: Remove the error in service mode when handling is completed.
Causes:	EEPROM defect in the carriage PCB is detected.
Remedy:	1 Perform [DIAGNOSIS > CR SYSTEM CHECK] to diagnose carriage system. No problem Replace CARRIAGE UNIT. Abnormal Replace MAIN PCB UNIT.

Error code:	EC0F 2F93
Description:	Carriage jam error (support number: 1318) • Only this error code assigns jam code also.
Causes:	The detected value of acceleration sensor toward Y and Z direction exceeds the threshold.
Remedy:	1 Open the access cover and check paper jam. When jam is found, remove the jam and check the operation again. Proper operation Complete. Check media specifications and use environment (temperature and humidity) of the customer, and give the customer appropriate instruction for jam prevention. Improper operation Replace CARRIAGE UNIT.

Error code:	EC0F 2F96
Description:	Carriage motor error (support number: 4801)
Causes:	While carriage system is in error status, operation is indicated from firmware.
Remedy:	1 Check the items below. a) Cable connection of the carriage motor. b) Looseness and abrasion of BELT, CARRIAGE. Appropriate Replace CARRIAGE UNIT. Inappropriate a) Connect the cable. b) Replace BELT, CARRIAGE.

Error code:	EC11 2F2A
Description:	Paper feed home position error (support number: 4801)
Causes:	Paper feed home position adjustment is failed.
Remedy:	1 Check the items below. a) Driving condition of PAPER FEED MOTOR. b) Installation of FILM, TIMING SLIT DISK, scratches, circumference shaving, and smear. c) Looseness and abrasion of BELT, PAPER TRANSPORT. d) Cable connection. e) Perform [DIAGNOSIS > I/O DISPLAY] and check the operation of PAPER FEED HOME POSITION SENSOR. Inappropriate condition or improper operation a) Replace MAIN PCB UNIT or PAPER FEED MOTOR. b) Perform cleaning or replace FILM, TIMING SLIT DISK. c) Reattach or replace BELT, PAPER TRANSPORT, or replace the gear. d) Connect the cable. e) Replace PAPER FEED ENCODER UNIT.

Error code:	EC12 2F29
Description:	Paper feed drive timeout (support number: 4801)
Causes:	Paper feed drive does not finish driving within the scheduled time.
Remedy:	1 Check the items below. a) Jam inside of the printer. b) Looseness and abrasion of BELT, PAPER TRANSPORT, and gear tooth skipping. Appropriate Go to 2. Inappropriate a) Remove jam. b) Replace BELT, PAPER TRANSPORT, or the gear. 2 Replace PAPER FEED MOTOR UNIT. The problem is resolved Complete. The problem is not resolved Replace PAPER FEED ENCODER UNIT.

Error code:	EC12 2F2B
Description:	Paper feed overload (support number: 4801)
Causes:	Paper feed motor keeps 100% output for a certain period.
Remedy:	1 Check the items below. a) Jam inside of the printer. b) Check if the paper in use has strong stiffness, is a heavy roll paper, or is easy to get curled. c) Smear or paper jam in the PAPER FEED ROLLER UNIT. Appropriate Go to 2. Inappropriate a) Remove jam. b) Change the paper to use. c) Perform cleaning or replace PAPER FEED ROLLER UNIT and HOLDER, LF BACK UP. 2 Replace FILM, TIMING SLIT DISK and PAPER FEED MOTOR UNIT. The problem is resolved Complete. The problem is not resolved Replace PAPER FEED ROLLER UNIT.

Error code:	EC12 2F2C
Description:	PAPER FEED motor error (support number: 4801)
Causes:	The paper does not reach to the specified position while driving the paper feed motor.
Remedy:	1 Check the items below. a) Jam inside of the printer. b) Check if the paper in use has strong stiffness, is a heavy roll paper, or is easy to get curled. c) Smear or paper jam in the PAPER FEED ROLLER UNIT. Appropriate Go to 2. Inappropriate a) Remove jam. b) Change the paper to use. c) Perform cleaning or replace PAPER FEED ROLLER UNIT and HOLDER, LF BACK UP. 2 Replace FILM, TIMING SLIT DISK and PAPER FEED MOTOR UNIT. The problem is resolved Complete. The problem is not resolved Replace PAPER FEED ROLLER UNIT.

Error code:	EC13 2F17
Description:	Platen suction fan error (support number: 4801)
Causes:	SUCTION FAN UNIT lock signal is detected.
Remedy:	1 Replace SUCTION FAN UNIT. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC15 2E23
Description:	Cutter blade unit error (support number: 4801)
Causes:	- CUTTER HOME POSITION SENSOR cannot be detected. - Abnormal encoder value is detected when returning the cutter to the home position.
Remedy:	1 Check the items below. a) Foreign substances on CUTTER BLADE UNIT. b) Perform [DIAGNOSIS > I/O DISPLAY] and check CUTTER HOME POSITION SENSOR operation. c) Check the harness connection. No foreign substance and proper condition Go to 2. Foreign substance is adhering or improper condition a) Remove the foreign substance. b) Replace CUTTER HOME POSITION SENSOR. c) Connect the harness. 2 Replace CUTTER MOTOR UNIT, W/ENCODER. The problem is resolved Complete. The problem is not resolved Replace the cutter.

Error code:	EC16 2021
Description:	Roll drive timeout (support number: 4801)
Causes:	The target value of operation command is not achieved when controlling ACTIVE ROLL BRAKE MOTOR.
Remedy:	1 Check the items below. a) Foreign substances or jam at paper feed part. b) Engagement of the spool with the gear of the printer side. c) Check if the paper in use has strong stiffness, is a heavy roll paper, or is easy to get curled. Appropriate Go to 2. Inappropriate a) Remove the foreign substance and jam. b) Reset the spool. c) Change the paper to use. 2 Replace ACTIVE ROLL BRAKE MOTOR. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC16 2022
Description:	Roll drive overload (support number: 4801)
Causes:	Current value reaches to the maximum value when controlling ACTIVE ROLL BRAKE MOTOR.
Remedy:	1 Check the items below. a) Foreign substances or jam at paper feed part. b) Engagement of the spool with the gear of the printer side. c) Check if the paper in use has strong stiffness, is a heavy roll paper, or is easy to get curled. Appropriate Go to 2. Inappropriate a) Remove the foreign substance and jam. b) Reset the spool. c) Change the paper to use. 2 Replace ACTIVE ROLL BRAKE MOTOR. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC16 2027
Description:	Role motor error (support number: 4801)
Causes:	The timing when roll drive timeout or upper roll drive overload occurs, operation instruction is indicated by firmware.
Remedy:	1 Check the items below. a) Foreign substances or jam at paper feed part. b) Engagement of the spool with the gear of the printer side. c) Check if the paper in use has strong stiffness, is a heavy roll paper, or is easy to get curled. Appropriate Go to 2. Inappropriate a) Remove the foreign substance and jam. b) Reset the spool. c) Change the paper to use. 2 Replace ACTIVE ROLL BRAKE MOTOR. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC16 202A
Description:	Roll motor drive control abnormal (support number: 4801)
Causes:	Abnormity is detected at control IC on the main PCB during ACTIVE ROLL BRAKE MOTOR controlling.
Remedy:	1 Check the items below. a) Foreign substances or jam at paper feed part. b) Engagement of the spool with the gear of the printer side. c) Check if the paper in use has strong stiffness, is a heavy roll paper, or is easy to get curled. Appropriate Go to 2. Inappropriate a) Remove the foreign substance and jam. b) Reset the spool. c) Change the paper to use. 2 Replace ACTIVE ROLL BRAKE MOTOR. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC16 202E
Description:	Upper roll spool detection error (support number: 100E)
Causes:	UPPER RIGHT SPOOL SET SENSOR or UPPER LEFT SPOOL SET SENSOR detects “No spool” when SPOOL LOCK UNIT is ON.
Remedy:	1 Check the items below. a) Engagement of the spool with the gear of the printer side. b) Check if the paper in use has strong stiffness, is a heavy roll paper, or is easy to get curled. c) Damage of the spool sensor lever. d) Perform [DIAGNOSIS > I/O DISPLAY] and check the operation of UPPER RIGHT SPOOL SET SENSOR and UPPER LEFT SPOOL SET SENSOR Appropriate Replace SPOOL LOCK UNIT. Inappropriate a) Reset the spool. b) Change the paper to use. c) Replace COVER, ROLL GEAR L and/or SPOOL SENSOR UNIT. d) Replace SPOOL SENSOR UNIT and/or UPPER LEFT SPOOL SET SENSOR when the connect condition of the harness is not troubled.

Error code:	EC16 2038
Description:	Roll motor calibration error (support number: 4801)
Causes:	Calibration of ACTIVE ROLL BRAKE MOTOR fails.
Remedy:	1 Check if a spool is installed in the roll unit. With the spool Remove the spool from the roll unit and reboot the main unit.* Without the spool Replace ACTIVE ROLL BRAKE MOTOR. *The spool must be removed before calibrating the roll unit.

Error code:	EC17 2023
Description:	Lower roll drive timeout (support number: 4801)
Causes:	Lower ACTIVE ROLL BRAKE UNIT does not reach to its motor control target value.
Remedy:	1 Check the items below. a) Foreign substances or jam at paper feed part. b) Engagement of the spool with the gear of the printer side. c) Check if the paper in use has strong stiffness, is a heavy roll paper, or is easy to get curled. Appropriate Go to 2. Inappropriate a) Remove the foreign substance and jam. b) Reset the spool. c) Change the paper to use. 2 Replace ACTIVE ROLL BRAKE UNIT. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT (Disassembly & Reassembly for 24. model, for 36. model, for 44. model). • After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC17 2024
Description:	Lower roll drive overload (support number: 4801)
Causes:	Current value reaches to the maximum value when controlling lower ACTIVE ROLL BRAKE UNIT motor.
Remedy:	1 Check the items below. a) Foreign substances or jam at paper feed part. b) Engagement of the spool with the gear of the printer side. c) Check if the paper in use has strong stiffness, is a heavy roll paper, or is easy to get curled. Appropriate Go to 2. Inappropriate a) Remove the foreign substance and jam. b) Reset the spool. c) Change the paper to use. 2 Replace ACTIVE ROLL BRAKE UNIT. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT (Disassembly & Reassembly for 24. model, for 36. model, for 44. model). • After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC17 2028
Description:	Lower roll motor error (support number: 4801)
Causes:	The timing when lower roll drive timeout or lower roll drive overload occurs, operation instruction is indicated by firmware.
Remedy:	1 Check the items below. a) Foreign substances or jam at paper feed part. b) Engagement of the spool with the gear of the printer side. c) Check if the paper in use has strong stiffness, is a heavy roll paper, or is easy to get curled. Appropriate Go to 2. Inappropriate a) Remove the foreign substance and jam. b) Reset the spool. c) Change the paper to use. 2 Replace ACTIVE ROLL BRAKE UNIT. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT (Disassembly & Reassembly for 24. model, for 36. model, for 44. model). • After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC17 2029
Description:	Lower roll motor drive control abnormal (support number: 4801)
Causes:	Abnormity is detected at control IC on the main PCB during lower ACTIVE ROLL BRAKE UNIT controlling.
Remedy:	1 Check the items below. a) Foreign substances or jam at paper feed part. b) Engagement of the spool with the gear of the printer side. c) Check if the paper in use has strong stiffness, is a heavy roll paper, or is easy to get curled. Appropriate Go to 2. Inappropriate a) Remove the foreign substance and jam. b) Reset the spool. c) Change the paper to use. 2 Replace ACTIVE ROLL BRAKE UNIT. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT (Disassembly & Reassembly for 24. model, for 36. model, for 44. model). • After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC17 202D
Description:	No lower roll unit (support number: 1875)
Causes:	• The lower roll unit is not recognized when starting printing from the lower roll. • The lower roll unit is not recognized despite feed available state of the lower roll.
Remedy:	1 Check the items below. a) Lower roll I/F cable connection. b) Lower roll unit connection. Connected Replace I/F PCB UNIT, RU and/or RELAY PCB UNIT, RU. Disconnected a) Connect the cable. b) Connect the unit.

Error code:	EC17 202F
Description:	Lower roll spool detection error (support number: 100F)
Causes:	LOWER RIGHT SPOOL SET SENSOR or LOWER LEFT SPOOL SET SENSOR detects “No spool” when spool lock solenoid is ON.
Remedy:	1 Check the items below. a) Engagement of the spool with the gear of the printer side. b) Check if the paper in use has strong stiffness, is a heavy roll paper, or is easy to get curled. c) Damage of the spool sensor lever. d) Perform [DIAGNOSIS > I/O DISPLAY] to check the operation of LOWER RIGHT SPOOL SET SENSOR and LOWER LEFT SPOOL SET SENSOR. Appropriate Replace SPOOL LOCK UNIT. Inappropriate a) Reset the spool. b) Change the paper to use. c) Replace COVER, ROLL GEAR L and/or LOCK LEVER A and/or LOCK LEVER B. d) Replace LOWER RIGHT SPOOL SET SENSOR and/or LOWER LEFT SPOOL SET SENSOR when the connect condition of the harness is not troubled.

Error code:	EC17 2039
Description:	Lower ARB motor calibration error (support number: 4801)
Causes:	Calibration of lower ACTIVE ROLL BRAKE UNIT motor fails.
Remedy:	1 Check if a spool is installed in the upper roll unit. With the spool Remove the spool from the upper roll unit and reboot the main unit* Without the spool Replace ACTIVE ROLL BRAKE UNIT. * The spool must be removed before calibrating the upper roll unit.

Error code:	EC17 203A
Description:	Non-supported lower roll unit installed (support number: 1039)
Causes:	Installation of an unsupported lower roll unit is detected.
Remedy:	1 Check the items below. a) The installed lower roll unit is for PRO series. b) Connection of the lower roll I/F cable. Correct roll unit and proper cable connection Replace I/F PCB UNIT, RU, RELAY PCB UNIT, RU, and lower roll I/F cable. Incorrect roll unit or improper c able connection a) Install the lower roll unit for TX series. b) Connect the cable.

Error code:	EC17 203D
Description:	Motor driver boot sequence failure of lower roll unit (support number: 4804)
Causes:	The motor driver boot sequence of lower roll unit was not completed properly in starting up.
Remedy:	1 Check the items below. a) Connection of the lower roll I/F cable. b) Installation of the lower roll unit. Correct roll unit and proper cable connection Replace I/F PCB UNIT, RU, RELAY PCB UNIT, RU, and lower roll I/F cable. Incorrect roll unit or improper cable connection a) Connect the cable. b) Install the lower roll unit.

Error code:	EC19 2F21
Description:	Release lever open error during printing (support number : 1214)
Causes:	Release lever is released during printing.
Remedy:	1 Start up the printer in service mode. Move the release lever back and forth in print waiting status. Perform [DIAGNOSIS > I/O DISPLAY] to check RELEASE LEVER SWITCH operation. Appropriate Replace RELEASE LEVER UNIT. Inappropriate Replace RELEASE LEVER SWITCH.

Error code:	EC1B 2030
Description:	Upper roll nip arm sensor non-detection (support number: 4801)
Causes:	UPPER ROLL NIP SENSOR cannot detect nip position when starting up or switching nip position.
Remedy:	1 Check the items below. a) Foreign substances around upper DRIVE NIP ARM UNIT. b) Perform [DIAGNOSIS> I/O DISPLAY] to check UPPER ROLL NIP SENSOR operation. Appropriate Replace DRIVE NIP ARM UNIT. Inappropriate a) Remove the foreign substance. b) Replace UPPER ROLL NIP SENSOR.

Error code:	EC1B 2031
Description:	Upper roll nip arm drive timeout (support number: 4801)
Causes:	Upper DRIVE NIP ARM UNIT does not complete driving within the scheduled time.
Remedy:	1 Check if foreign substances are adhering around upper DRIVE NIP ARM UNIT. Without foreign substance Replace DRIVE NIP ARM UNIT. With foreign substances Remove the foreign substance.

Error code:	EC1B 2032
Description:	Upper roll nip arm drive overload (support number: 4801)
Causes:	The motor of upper DRIVE NIP ARM UNIT keeps 100% output for more than a specified duration.
Remedy:	1 Check if foreign substances are adhering around upper DRIVE NIP ARM UNIT. Without foreign substance Replace DRIVE NIP ARM UNIT. With foreign substances Remove the foreign substance.

Error code:	EC1B 2033
Description:	Upper roll nip arm motor error (support number: 4801)
Causes:	At the timing when upper DRIVE NIP ARM UNIT drive timeout or drive overload occurs, firmware receives operation command.
Remedy:	1 Check if foreign substances are adhering around upper DRIVE NIP ARM UNIT. Without foreign substance Replace DRIVE NIP ARM UNIT. With foreign substances Remove the foreign substance.

Error code:	EC1C 2034
Description:	Lower roll nip arm sensor non-detection (support number: 4801)
Causes:	LOWER ROLL NIP SENSOR fails to detect nip position when starting up or shifting nip position.
Remedy:	1 Check the items below. a) Foreign substances around lower DRIVE NIP ARM UNIT. b) Perform [DIAGNOSIS > I/O DISPLAY] to check LOWER ROLL NIP SENSOR operation. No foreign substance and proper operation Replace DRIVE NIP ARM UNIT. Foreign substance is adhering or improper operation a) Remove the foreign substance. b) Replace LOWER ROLL NIP SENSOR.

Error code:	EC1C 2035
Description:	Lower roll nip arm drive timeout (support number: 4801)
Causes:	Lower DRIVE NIP ARM UNIT does not finish driving within the scheduled time.
Remedy:	1 Check if foreign substances are adhering around lower DRIVE NIP ARM UNIT. Without foreign substance Replace DRIVE NIP ARM UNIT. With foreign substances Remove the foreign substance.

Error code:	EC1C 2036
Description:	Lower roll nip arm drive overload (support number: 4801)
Causes:	The motor of lower DRIVE NIP ARM UNIT keeps 100% output for longer than the specified duration.
Remedy:	1 Check if foreign substances are adhering around lower DRIVE NIP ARM UNIT. No foreign substance Replace DRIVE NIP ARM UNIT. Foreign substances are adhering Remove the foreign substances.

Error code:	EC1C 2037
Description:	Lower roll nip arm motor error (support number: 4801)
Causes:	At the timing when lower DRIVE NIP ARM UNIT drive timeout or drive overload occurs, firmware receives operation command.
Remedy:	1 Check if foreign substances are adhering around lower DRIVE NIP ARM UNIT. Without foreign substance Replace DRIVE NIP ARM UNIT. With foreign substances Remove the foreign substance.

Error code:	EC1D 2050
Description:	Upper roll paper set sensor error (support number: 4805)
Causes:	Communicating with the upper roll paper set sensor failed when loading the upper roll paper.
Remedy:	1 Check the cable connection of ROLL PAPER SET SENSOR UNIT (for upper roll). Proper connection Replace NIP ARM SENSOR UNIT (for upper roll). Improper connection Connect the cable.

Error code:	EC1E 2053
Description:	Lower roll paper set sensor error (support number: 4805)
Causes:	Communicating with the lower roll paper set sensor failed when loading the lower roll paper.
Remedy:	1 Check the cable connection of ROLL PAPER SET SENSOR UNIT (for lower roll). Proper connection Replace NIP ARM SENSOR UNIT (for lower roll). Improper connection Connect the cable.

Error code:	EC21 282D
Description:	Print head Si melting (reboot request) (support number: 140C)
Causes:	Si solution amount is more than the standard solution amount.
Remedy:	1 Reboot the printer.

Error code:	EC21 282E
Description:	Print head Si melting (print head replacement request) (support number: 1403)
Causes:	The printer does not recover by rebooting after print head Si solution error.
Remedy:	1 Replace the print head.

Error code:	EC21 2F43
Description:	Print head 640 nozzles complete non-ejection (support number: 1494)
Causes:	Non-ejection in 640 nozzles is detected through non-ejection detection.
Remedy:	1 When the printer does not recover by rebooting, check if the ink is filled into tubes. Ink is filled Go to 2. Ink is not filled Replace the INK TUBE UNIT. 2 Perform deep cleaning, and print nozzle check pattern. Proper nozzle pattern Complete. Improper nozzle pattern Replace the print head.

Error code:	EC21 2F44
Description:	Abnormal increase of non-ejection nozzles from last non-ejection detection (support number: 1492)
Causes:	At the rate of fifty or more non-ejection nozzles per one nozzle have increased since last non-ejection detection.
Remedy:	1 Perform deep cleaning and print nozzle check pattern. Proper nozzle pattern Complete. Improper nozzle pattern Replace the print head.

Error code:	EC21 2F50
Description:	VH leak at print head replacement (support number: 1477)
Causes:	VH leak is detected at print head replacement.
Remedy:	1 Perform [DIAGNOSIS > CR SYSTEM CHECK] to diagnose carriage system. No problem Go to 2. Problem in LONG FFC CHECK Replace CARRIAGE UNIT. 2 Remove the print head and check the condition of print head contacting part. Proper condition Replace the print head. Improper condition Go to 3. 3 Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC21 2F51
Description:	VH leak at starting up, cleaning, or print starting (support number: 4801)
Causes:	VH leak is detected at starting up, cleaning, and print starting.
Remedy:	1 Reboot the printer.

Error code:	EC21 2F53
Description:	VH leak at rebooting (support number: 1478)
Causes:	The printer does not recover by rebooting after the VH leak error at starting up, cleaning, or print starting.
Remedy:	1 Perform [DIAGNOSIS > CR SYSTEM CHECK] to diagnose carriage system. No problem Go to 2. Problem in LONG FFC CHECK Replace CARRIAGE UNIT. 2 Remove the print head and check the condition of print head contacting part. Proper condition Replace the print head. Improper condition Go to 3. 3 Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC21 2F54
Description:	Print head VH voltage abnormal (support number: 4801)
Causes:	Abnormal VH voltage of the print head is detected.
Remedy:	1 Perform [DIAGNOSIS > CR SYSTEM CHECK] to diagnose carriage system. No problem Go to 2. Problem in LONG FFC CHECK Replace CARRIAGE UNIT. 2 Remove the print head and check the condition of print head contacting part. Proper condition Replace the print head. Improper condition Go to 3. 3 Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC21 2F56
Description:	VHTR leak at print head replacement (support number: 1477)
Causes:	VHTR leak is detected at print head replacement.
Remedy:	1 Perform [DIAGNOSIS > CR SYSTEM CHECK] to diagnose carriage system. No problem Go to 2. Problem in LONG FFC CHECK Replace CARRIAGE UNIT. 2 Remove the print head and check the condition of print head contacting part. Proper condition Replace the print head. Improper condition Go to 3. 3 Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC21 2F57
Description:	VHTR leak error at starting up, cleaning, or print starting (support number: 4801)
Causes:	VHTR leakage is detected in starting up, cleaning, or print starting.
Remedy:	1 Reboot the printer.

Error code:	EC21 2F58
Description:	VHTR leak at rebooting (support number: 1478)
Causes:	The printer does not recover by rebooting after the VHTR leak error occurred in starting up, cleaning, or print starting.
Remedy:	1 Perform [DIAGNOSIS > CR SYSTEM CHECK] to diagnose carriage system. No problem Go to 2. Problem in LONG FFC CHECK Replace CARRIAGE UNIT. 2 Remove the print head and check the condition of print head contacting part. Proper condition Replace the print head. Improper condition Go to 3. 3 Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC21 2F59
Description:	Print head VHTR voltage abnormal (support number: 4801)
Causes:	Abnormal VHTR voltage of the print head is detected.
Remedy:	1 Perform [DIAGNOSIS > CR SYSTEM CHECK] to diagnose carriage system. No problem Go to 2. Problem in LONG FFC CHECK Replace CARRIAGE UNIT. 2 Remove the print head and check the condition of print head contacting part. Proper condition Replace the print head. Improper condition Go to 3. 3 Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC21 2F60
Description:	H3V voltage abnormal at print head replacement (support number: 1477)
Causes:	Abnormal H3V voltage is detected at print head replacement.
Remedy:	1 Perform [DIAGNOSIS > CR SYSTEM CHECK] to diagnose carriage system. No problem Go to 2. Problem in LONG FFC CHECK Replace CARRIAGE UNIT. 2 Remove the print head and check the condition of print head contacting part. Proper condition Replace the print head. Improper condition Go to 3. 3 Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC21 2F61
Description:	H3V voltage abnormal at starting up, cleaning, or print starting (support number: 4801)
Causes:	Abnormal H3V voltage is detected at starting up, cleaning, or print starting.
Remedy:	1 Reboot the printer.

Error code:	EC21 2F62
Description:	H3V leak at rebooting (support number: 1478)
Causes:	The printer does not recover by rebooting after the H3V leak error at starting up, cleaning, or print starting.
Remedy:	1 Perform [DIAGNOSIS > CR SYSTEM CHECK] to diagnose carriage system. No problem Go to 2. Problem in LONG FFC CHECK Replace CARRIAGE UNIT. 2 Remove the print head and check the condition of print head contacting part. Proper condition Replace the print head. Improper condition Go to 3. 3 Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC21 2F63
Description:	Print head contact error at print head replacement (support number: 1479)
Causes:	Direct diode sensor detects print head contact failure at print head replacement.
Remedy:	1 Remove the print head and check the condition of print head contacting part. Proper condition Go to 2. Improper condition Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) 2 Perform [DIAGNOSIS > CR_SYSTEM_CHECK] to check the result of LONG FFC CHECK. Without broken wires Replace CARRIAGE UNIT. With broken wires Replace FLEXIBLE CABLE UNIT.

Error code:	EC21 2F64
Description:	Print head contact error at starting up (support number: 4801)
Causes:	Direct diode sensor detects print head contact failure at print head replacement.
Remedy:	1 Perform [DIAGNOSIS > CR_SYSTEM_CHECK] to diagnose carriage system. No problem Go to 2. Abnormal ¡¤¡¤Problem in ACC. SENSOR CHECK or CR VIBRATIONCHECK Replace CARRIAGE UNIT. ¡¤¡¤Problem in LONG FFC CHECK Replace FLEXIBLE CABLE UNIT. 2 Remove the print head, and check the items below. a) Condition of the print head nozzle side surface. b) Condition of the print head contacting part Proper condition Go to 3 Abnormal condition a) Replace the print head. b) Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) 3 Replace MAIN PCB UNIT (Disassembly & Reassembly for 24. model, for 36. model, for 44. model). • After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC21 2F67
Description:	Print head H3V voltage abnormal during printing (support number: 4801)
Causes:	Abnormal H3V voltage of the print head is detected during printing.
Remedy:	1 Perform [DIAGNOSIS > CR SYSTEM CHECK] to diagnose carriage system. No problem Go to 2. Problem in LONG FFC CHECK Replace CARRIAGE UNIT. 2 Remove the print head and check the condition of print head contacting part. Proper condition Replace the print head. Improper condition Go to 3. 3 Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC21 2F6D
Description:	Print head EEPROM checksum error 2 (support number: 140F)
Causes:	Abnormity is detected in checksum judgement of EEPROM at print head installation and starting up.
Remedy:	1 Replace the print head.

Error code:	EC21 2F70
Description:	Print head diode temperature abnormal (reboot request) (support number: 1408)
Causes:	Abnormal temperature of the diode is detected at diode correction.
Remedy:	1 Reboot the printer.

Error code:	EC21 2F71
Description:	Print head diode temperature unstable (support number: 1409)
Causes:	Diode temperature is detected to be unstable at diode correction.
Remedy:	1 Reboot the printer.

Error code:	EC21 2F72
Description:	Print head diode correction error (reboot request) (support number: 140A)
Causes:	Abnormal value is detected at diode correction.
Remedy:	1 Reboot the printer.

Error code:	EC21 2F73
Description:	Print head diode temperature abnormal (print head replacement request) (support number: 1408)
Causes:	The printer does not recover by rebooting after this error.
Remedy:	1 Replace the print head.

Error code:	EC21 2F74
Description:	Print head diode temperature unstable (print head replacement request) (support number: 1409)
Causes:	The printer does not recover by rebooting after this error.
Remedy:	1 Replace the print head.

Error code:	EC21 2F75
Description:	Print head diode correction error (print head replacement request) (support number: 140A)
Causes:	The printer does not recover by rebooting after this error.
Remedy:	1 Replace the print head.

Error code:	EC21 2F7D
Description:	Print head contact error before non-ejection detection (support number: 4801)
Causes:	Sending command to the print head is disabled.
Remedy:	1 Remove the print head and check the condition of print head contacting part. Proper condition Go to 2. Abnormal condition Clean the surface of the print head contacting part. (The waste cloth without a nap must be used.) 2 Perform [DIAGNOSIS > CR_SYSTEM_CHECK] to diagnose carriage system. No problem Replace the print head. Abnormal • Problem in ACC. SENSOR CHECK or CR VIBRATIONCHECK Replace CARRIAGE UNIT. • Problem in LONG FFC CHECK Replace FLEXIBLE CABLE UNIT.

Error code:	EC21 2F7E
Description:	Print head temperature abnormal (reboot request) (support number: 5200)
Causes:	Abnormal temperature of heater board is detected.
Remedy:	1 Reboot the printer.

Error code:	EC21 2F7F
Description:	Print head temperature abnormal (print head replacement request) (support number: 1478)
Causes:	The printer detects print head abnormal temperature rising and does not recover by rebooting.
Remedy:	1 Replace the print head.

Error code:	EC22 2F30
Description:	Head management sensor position adjustment error (support number: 4801)
Causes:	Adjusting head management sensor position is failed.
Remedy:	1 Check if the ink is filled into ink tubes. Ink is filled Go to 2. Ink is not filled Perform [DIAGNOSIS > PURGE CHECK] to diagnose ink vacuum of PURGE UNIT. PURGE UNIT ink vacuum diagnosis Proper operation Perform deep cleaning and fill the ink. When the ink vacuum does not recover, replace the print head. Abnormal operation Replace PURGE UNIT. 2 Print user nozzle check pattern or service nozzle check pattern to check the nozzle condition. (Check if blur or non-ejection appears at the top and bottom edge line of the nozzle check pattern.) Appropriate condition Replace HEAD MANAGEMENT SENSOR UNIT. Abnormal condition Perform deep cleaning and fill the ink. When the ink vacuum does not recover, replace the print head.

Error code:	EC22 2F47
Description:	Head management sensor unit failure (support number: 4801)
Causes:	The head management sensor unit is detected to be faulty at starting up or nonejection detection.
Remedy:	1 Check the items below. a) Adherence of paper dust and hairs on the HEAD MANAGEMENT SENSOR UNIT. b) Adherence or laying-up of large amount of ink mist on the HEAD MANAGEMENT SENSOR UNIT. c) Connector condition. Appropriate condition and proper connection Go to 2. Inappropriate condition or improper connection a) Remove it. b) Perform cleaning or replace HEAD MANAGEMENT SENSOR UNIT. c) Connect the connector. 2 Check if the fuse (FU5202) on MAIN PCB UNIT is disconnected. Connected Replace HEAD MANAGEMENT SENSOR UNIT. Disconnected Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC22 4001
Description:	End-of-life of head management sensor unit (support number: 5B16) Memo : Remove the error in service mode after handling.
Causes:	Ink amount in the head management sensor exceeds the threshold.
Remedy:	1 Replace HEAD MANAGEMENT SENSOR UNIT.

Error code:	EC23 260E
Description:	Gap adjustment error (support number: 4801)
Causes:	Abnormity is detected at GAP adjustment.
Remedy:	1 Check the cable connection of MULTI SENSOR UNIT. Proper connection Replace MULTI SENSOR UNIT. Improper connection Connect the cable.

Error code:	EC23 2F11
Description:	Multi sensor bus communication error (support number: 4801)
Causes:	Communicating with multi sensor related hard ware, such as LED driver and multi sensor EEPROM, is failed.
Remedy:	1 Check the cable connection of MULTI SENSOR UNIT. Proper connection Replace MULTI SENSOR UNIT. Improper connection Connect the cable. This error is caused by multi sensor malfunction. Communication error of other ICs is indicated when communication failure occurs, since confirmation of communication with other ICs in the carriage is performed prior to confirmation of communication of the multi sensor.

Error code:	EC23 2F18
Description:	Carriage board I2C bus communication error (support number: 4801)
Causes:	I2C writing and reading to ICs on the carriage board is failed.
Remedy:	1 Perform [DIAGNOSIS > CR SYSTEM CHECK], and check LONG FFC CHECK result and the CRC value change before and after turning off and on the power. (The value change is indicating broken wire.) Normal result Replace CARRIAGE UNIT. Abnormal result Replace MAIN PCB UNIT.

Error code:	EC23 2F32
Description:	Multi sensor error (support number: 4801)
Causes:	Abnormity is detected in multi sensor EEPROM reading at each automatic adjustment, paper edge detection, GAP adjustment, and starting up.
Remedy:	1 Check the cable connection of MULTI SENSOR UNIT. Proper connection Replace MULTI SENSOR UNIT. Improper connection Connect the cable.

Error code:	EC24 4049
Description:	Abnormal temperature by temperature and humidity sensor (support number: 8200) Memo: Remove the error in service mode after handling.
Causes:	Abnormity is detected at reading temperature
Remedy:	1 Check the cable connection of SENSOR, HUMIDITY. Proper connection Replace SENSOR, HUMIDITY. Improper connection Connect the cable.

Error code:	EC24 404A
Description:	Abnormal humidity by temperature and humidity sensor (support number: 8200) Memo: Remove the error in service mode after handling.
Causes:	Abnormity is detected at reading humidity.
Remedy:	1 Check the cable connection of SENSOR, HUMIDITY. Proper connection Replace SENSOR, HUMIDITY. Improper connection Connect the cable.

Error code:	EC24 404B
Description:	Temperature and humidity sensor non-connection (support number: 8200) Memo: Remove the error in service mode after handling.
Causes:	Abnormity is detected at reading temperature and humidity.
Remedy:	1 Check the cable connection of SENSOR, HUMIDITY. Proper connection Replace SENSOR, HUMIDITY. Improper connection Connect the cable.

Error code:	EC25 2F16
Description:	Mist fan error (support number: 4801)
Causes:	Abnormity is detected at reading humidity.
Remedy:	1 Check the cable connection of MIST FAN. Proper connection Go to 2. Improper connection Connect the cable. 2 Replace EXHAUST MIST DUCT UNIT. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC25 4001
Description:	End-of-life of mist collecting duct (support number: 5B20) Memo: Remove the error in service mode after handling.
Causes:	Ink amount in the mist collecting duct exceeds the threshold.
Remedy:	1 Replace EXHAUST MIST DUCT UNIT.

Error code:	EC31 2F09
Description:	Wiper blade encoder and motor error (support number: 4801)
Causes:	The encoder does not detect the wiper moved to the specified position.
Remedy:	1 Check if the foreign substances such as paper debris are adhering around PURGE UNIT. Without foreign substances Go to 2. With foreign substances Remove the foreign substances. 2 Perform [DIAGNOSIS > PURGE CHECK > INITIALIZE CHECK] to check purge unit operation. Proper operation Reboot and recheck operation. Improper operation Replace PURGE UNIT.

Error code:	EC31 2F10
Description:	Wiper blade motor overload (support number: 4801)
Causes:	The motor keeps 100% output.
Remedy:	1 Check if the foreign substances such as paper debris are adhering around PURGE UNIT. Without foreign substances Go to 2. With foreign substances Remove the foreign substances. 2 Perform [DIAGNOSIS > PURGE CHECK > INITIALIZE CHECK] to check purge unit operation. Proper operation Reboot and recheck operation. Improper operation Replace PURGE UNIT.

Error code:	EC31 2F1B
Description:	Wiper blade position detecting sensor error (support number: 4801)
Causes:	WIPER POSITION SENSOR does not detect wiper position despite having moved the wiper to the specified position.
Remedy:	1 Check if the foreign substances such as paper debris are adhering around PURGE UNIT. Without foreign substances Go to 2. With foreign substances Remove the foreign substances. 2 Perform [DIAGNOSIS > PURGE CHECK > INITIALIZE CHECK] to check purge unit operation. Proper operation Reboot and recheck operation. Improper operation Replace PURGE UNIT.

Error code:	EC31 2F1C
Description:	Purge main cam sensor error (support number: 4801)
Causes:	The following failure is detected. - Initialization of purge main cam position is failed. - Moving CARRIAGE UNIT to the specified position is disabled when capping.
Remedy:	1 Check the items below. a) The foreign substances such as paper debris are adhering around PURGE UNIT. b) Scratch or stain on SCALE, LINER. Without paper debris, scratch, or stain Go to 2. With paper debris, scratch, or stain a) Remove the foreign substance. b) Perform cleaning or replace SCALE, LINEAR. 2 After unlocking CARRIAGE UNIT with [FUNCTION > CR UNLOCK], perform [FUNCTION > CR LOCK] to check CARRIAGE UNIT lock operation. Proper operation Reboot and recheck the operation. Abnormal operation Replace PURGE UNIT.

Error code:	EC31 2F1D
Description:	Purge motor error (support number: 4801)
Causes:	The motor does not operate.
Remedy:	1 Check if the foreign substances such as paper debris are adhering around PURGE UNIT. Without foreign substance Go to 2. With foreign substances Remove the foreign substance. 2 Perform [DIAGNOSIS > PURGE CHECK > INITIALIZE CHECK] to check purge unit operation. Proper operation Reboot and recheck the operation. Abnormal operation Replace PURGE UNIT.

Error code:	EC31 2F1E
Description:	Purge motor overload (support number: 4801)
Causes:	The motor keeps 100% output, or PURGE MOTOR ENCODER cannot be read.
Remedy:	1 Check if the foreign substances such as paper debris are adhering around PURGE UNIT, and also check the connector connection. Proper connection without foreign substance Go to 2. With foreign substances or improper connection Remove the foreign substance or connect the connector properly. 2 Perform [DIAGNOSIS > PURGE CHECK > INITIALIZE CHECK] to check purge unit operation. Proper operation Reboot and recheck the operation. Abnormal operation Replace PURGE UNIT.

Error code:	EC31 2F1F
Description:	Pump roller position detecting sensor error (support number: 4801)
Causes:	The PUMP ROLLER SENSOR fails to detect pump rolling position when driving the pump.
Remedy:	1 Check if the foreign substances such as paper debris are adhering around PURGE UNIT. Without foreign substance Go to 2. With foreign substances Remove the foreign substance. 2 Perform [DIAGNOSIS > PURGE CHECK > INITIALIZE CHECK] to check purge unit operation. Proper operation Reboot and recheck the operation. Abnormal operation Replace PURGE UNIT.

Error code:	EC31 2F22
Description:	Purge motor drive timeout (support number: 4801)
Causes:	The purge motor drive does not complete the specified operation within the specified time.
Remedy:	1 Check if the foreign substances such as paper debris are adhering around PURGE UNIT. Without foreign substance Go to 2. With foreign substances Remove the foreign substance. 2 Perform [DIAGNOSIS > PURGE CHECK > INITIALIZE CHECK] to check purge unit operation. Proper operation Reboot and recheck the operation. Abnormal operation Replace the PURGE UNIT.

Error code:	EC31 2F23
Description:	Wiper blade motor drive timeout (support number: 4801)
Causes:	The purge motor drive does not complete the specified operation within the specified time.
Remedy:	1 Check if the foreign substances such as paper debris are adhering around PURGE UNIT. Without foreign substance Go to 2. With foreign substances Remove the foreign substance. 2 Perform [DIAGNOSIS > PURGE CHECK > INITIALIZE CHECK] to check purge unit operation. Proper operation Reboot and recheck the operation. Abnormal operation Replace the PURGE UNIT.

Error code:	EC31 2F94
Description:	Carriage obstacle error (support number: 4801)
Causes:	When the detected value by acceleration sensor exceeds the threshold. In addition, is in the opposite direction of CARRIAGE UNIT scanning direction.
Remedy:	1 Check the items below. a) The foreign substances such as paper debris around PURGE UNIT. b) The purge lock pin to strikes to CARRIAGE UNIT during CARRIAGE UNIT operation. No foreign substance and the purge lock pin does not strike Go to 2. Foreign substance is adhering or the purge lock pin strikes a) Remove the foreign substance. b) Replace the PURGE UNIT.

Error code:	EC31 4001
Description:	End-of-life of purge unit (support number: 5C00) Memo : Remove the error in service mode after handling.
Causes:	The purge unit lifespan runs out.
Remedy:	1 Replace the PURGE UNIT.

Error code:	EC32 4001
Description:	End-of-life of tube unit (support number: B510) Memo : Remove the error in service mode after handling.
Causes:	The amount of carriage scan time exceeds the threshold, and the tube unit lifespan runs out.
Remedy:	1 Replace the INK TUBE UNIT.

Error code:	EC33 402x
Description:	Choke valve leak at initial ink filling (support number: 5A60) Memo : Remove the error in service mode after handling.
Causes:	The ink level detection pin detects ink filling failure of the sub tank. Reference: Ink colors are identified with the last number of detail codes.
Remedy:	1 Replace the SUB INK TANK UNIT that ink filling error occurred. (Disassembly & Reassembly for SUB INK TANK UNIT R)

Error code:	EC34 2602
Description:	Right choke valve drive timeout (support number: 4801)
Causes:	The choke valve does not complete driving within the scheduled time.
Remedy:	1 Perform [DIAGNOSIS > I/O DISPLAY] to check the RIGHT CHOKE VALVE POSITION SENSOR operation. Proper operation Reboot and recheck the operation. When the printer does not recover, drive system overload is suspected. In this case, replace the INK SUPPLY TANK UNIT R. Abnormal operation Replace the INK SUPPLY TANK UNIT R.

Error code:	EC34 2605
Description:	Right agitation valve drive timeout (support number: 4801)
Causes:	The agitation valve does not complete driving within the scheduled time.
Remedy:	1 Perform [DIAGNOSIS > I/O DISPLAY] to check the RIGHT CHOKE VALVE POSITION SENSOR operation. Proper operation Reboot and recheck the operation. When the printer does not recover, drive system overload is suspected. In this case, replace the SUB INK TANK UNIT R. Abnormal operation Replace the SUB INK TANK UNIT R.

Error code:	EC34 2F3B
Description:	Right ink valve motor error (support number: 4801)
Causes:	Encoder value of the right ink valve motor is not detected.
Remedy:	1 Replace the INK SUPPLY TANK UNIT R.

Error code:	EC3F 2F40
Description:	Complete non-ejection in all colors through non-ejection detection (support number: 1492)
Causes:	Complete non-ejection in all colors through non-ejection detection.
Remedy:	1 Check the items below. a) Foreign substances such as paper debris around HEAD MANAGEMENT SENSOR UNIT. b) Tubes are filled by ink. No foreign substances and ink is filled Go to 2. Foreign substances are adhering or tubes are not filled by ink. a) Remove the foreign substance. b) Go to 3. There is little possibility of print head contact failure factor (because print head contact failure is checked by the automatic diagnosis at print head installation or before performing non-ejection detection). 2 Check the items below. a) Whether the service nozzle check pattern can be printed. b) Perform [DIAGNOSIS > CR SYSTEM CHECK] , and check LONG FFC CHECK result. Printable without broken wires Replace HEAD MANAGEMENT SENSOR UNIT. Not printable or broken wires a) Replace the print head. b) Replace the CARRIAGE UNIT. 3 Perform [DIAGNOSIS > PURGE CHECK > PRESSURE CHECK] to check vacuum operation of PURGE UNIT. Proper operation Replace the INK TUBE UNIT. Abnormal operation Replace the PURGE UNIT.

Error code:	EC3F 2F41
Description:	Complete non-ejection in one color (support number: 1492)
Causes:	Non-ejection in all nozzles of the one color is detected through non-ejection detection after cleaning.
Remedy:	1 Check if the ink is filling into tubes. Ink is filled Go to 2. (Insufficient ink in the print head or print head defect is suspected.) Ink is not filled Go to 3. 2 Perform deep cleaning and print nozzle check pattern. Appropriate condition Replace the ink supply tank unit that does not have ink filled in the tube. Abnormal condition Replace the print head.

Error code:	EC3F 4120 ... 4126
Description:	Ink vacuum error at initial ink filling. (support number: B510) Memo: Remove the error in service mode when handling is completed.
Causes:	After filling ink to the sub tank, ink filling into the tubes and the print head fails.
Remedy:	1 Check if ink is filling each tube and check ink filling condition by each cap. Not ink filling failure by each cap Go to 2. Ink filling failure by each cap Replace the PURGE UNIT. <The places to check ink filling condition of ink tubes> <The ink to be vacuumed by each cap> MBK,BK,MBK Y, M, C 2 Perform [FUNCTION > HEAD REPLACEMENT] and remove the print head. Install the other print head. Then, check the installation function. Proper function Replace the print head. Improper function Go to 3. 3 Replace the TUBE UNIT. The problem is resolved Complete. The problem is not resolved Replace the sub tank unit, the SUB INK TANK UNIT R, of the color that ink has not been filled.

Error code:	EC41 4001
Description:	End-of-life of SUCTION FAN UNIT (support number: 5B20) Memo : Remove the error in service mode after handling.
Causes:	Ink filled up in SUCTION FAN UNIT is detected.
Remedy:	1 Replace the SUCTION FAN UNIT.

Error code:	EC43 4001
Description:	End-of-life of WASTE INK BOX UNIT, HP (support number: 5B20) Memo : Remove the error in service mode after handling.
Causes:	Ink filled up in WASTE INK BOX UNIT, HP is detected.
Remedy:	1 Replace the WASTE INK BOX UNIT, HP.

Error code:	EC44 4001
Description:	End-of-life of WASTE INK BOX UNIT, CENTER (support number: 5B20) Memo : Remove the error in service mode after handling.
Causes:	Ink filled up in WASTE INK BOX UNIT, CENTER is detected.
Remedy:	1 Replace the WASTE INK BOX UNIT, CENTER.

Error code:	EC45 4001
Description:	End-of-life of waste ink absorber unit C (support number: 5B20) Memo : Remove the error in service mode after handling.
Causes:	Ink filled up in WASTE INK ABSORBER UNIT C is detected.
Remedy:	1 Replace the WASTE INK ABSORBER UNIT C.

Error code:	EC47 4001
Description:	End-of-life of WASTE INK BOX UNIT, BP (support number: 5B20) Memo : Remove the error in service mode after handling.
Causes:	Ink filled up in WASTE INK BOX UNIT, BP is detected.
Remedy:	1 Replace the WASTE INK BOX UNIT, BP.

Error code:	EC48 4001
Description:	End-of-life of MCG GUIDE UNIT (support number: 5B21) Memo : Remove the error in service mode after handling.
Causes:	Ink full in the MCG GUIDE UNIT of the maintenance cartridge is detected.* *Without having the maintenance cartridge installed, when the waste ink flows into the maintenance cartridge, the counter counts. (This case is not usually happens.)
Remedy:	1 Replace the MCG GUIDE UNIT.

Error code:	EC49 4001
Description:	End-of-life of waste ink tank unit (support number: 5B20) Memo : Remove the error in service mode after handling.
Causes:	Ink filled up in WASTE INK ABSORBER UNIT E is detected.
Remedy:	1 Replace the WASTE INK ABSORBER UNIT E.

Error code:	EC51 203C
Description:	Motor driver boot sequence failure (support number: 4803)
Causes:	Motor driver boot sequence was not completed properly in starting up.
Remedy:	1 When the printer does not recover by rebooting, replace MAIN PCB UNIT* . *After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 2F07
Description:	USB Vbus overcurrent (support number: 9000)
Causes:	Vbus overcurrent is detected.
Remedy:	1 Reboot.

Error code:	EC51 2F14
Description:	Main PCB I2C bus error (support number: 4801)
Causes:	Abnormal checksum value of the ink agitation timer or ink cleaning timer is detected, or accessing DA converter is disabled.
Remedy:	1 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 2F15
Description:	Unable to allocate memory (support number: 4801)
Causes:	Acquisition of OS memory pool packet is disabled.
Remedy:	1 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments..

Error code:	EC51 2F38
Description:	Access cover open error at the cover locking (support number: 1214)
Causes:	Cover open is detected when the access cover is being locked.
Remedy:	1 Close the access cover, and reboot. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT (Disassembly & Reassembly for 24. model, for 36. model, for 44. model). • After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 2FDE
Description:	Right ink level detection error (support number: 4801)
Causes:	Inactivation of the ink level detection pin of the sub ink tank in INK SUPPLY TANK UNIT R is detected, while activation of the ink level detection pin of the ink tank is detected. (It occurs with cable connection failure. This state does not normally occur.)
Remedy:	1 Check the connection of the MAIN PCB UNIT. Proper connection Replace MAIN PCB UNIT. Improper connection Connect the connector. The location to check the connection of the left MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3000
Description:	Network sub-system start-up error (support number: 6900)
Causes:	Starting up sequence of Network sub-system is failed.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Reinstall the firmware.

Error code:	EC51 3001
Description:	Network sub-system timeout (support number: 6901)
Causes:	Network sub system does not respond.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Reinstall the firmware.

Error code:	EC51 3004
Description:	Wired LAN driver error (support number: 6920)
Causes:	The fatal error occurs in the ethernet driver.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3005
Description:	Wired LAN hardware error (support number: 6921)
Causes:	Ethernet driver is physically broken.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Check the connection of the I/F PCB UNIT and the MAIN PCB UNIT. The problem is resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments. The problem is not resolved Connect the I/F PCB UNIT to the MAIN PCB UNIT.

Error code:	EC51 3006
Description:	Other network sub-system errors (support number: 6902)
Causes:	Starting up sequence of network sub-system fails.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3100
Description:	USB control-out bus error (support number: 6930)
Causes:	Bus error occurs at USB control-out end point.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Check the cable connection and if the cable in use supports USB2.0. When proper connection and USB2.0 is supported, reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3101
Description:	USB control-in bus error (support number: 6931)
Causes:	USB control-in end point bus error occurs.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Check the cable connection and if the cable in use supports USB2.0. When proper connection and USB2.0 is supported, reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3102
Description:	USB print bulk-out bus error (support number: 6932)
Causes:	Bus error occurs at print bulk-out end point.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Check the cable connection and if the cable in use supports USB2.0. When proper connection and USB2.0 is supported, reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3103
Description:	USB print bulk-in bus error (support number: 6933)
Causes:	Bus error occurs at print bulk-in end point.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Check the cable connection and if the cable in use supports USB2.0. When connection is proper and USB2.0 is supported, reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3104
Description:	USB sub-system firmware error (support number: 6940)
Causes:	USB firm error occurs.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3105
Description:	USB sub-system command error (support number: 6941)
Causes:	USB command error occurs.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Check the cable connection and if the cable in use supports USB2.0. When connection is proper and USB2.0 is supported, reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3106
Description:	USB sub-system timeout (support number: 6942)
Causes:	USB watchdog error occurs.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3107
Description:	USB sub-system data copy error (support number: 6943)
Causes:	USB-Relax firmware data copy error occurs.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3108
Description:	USB sub-system instruction error (support number: 6944)
Causes:	USB-Relax firmware instruction copy error is occurs.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3109
Description:	USB sub-system not started properly (support number: 6945)
Causes:	Boot error of USB-Relax firmware occurs.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3110
Description:	USB sub-system improper timeout setting (support number: 6946)
Causes:	Initial value set error of USB-Relax firmware watchdog occurs.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3301
Description:	Sub-chip connection error (support number: 4801)
Causes:	When starting up the printer or returning from power saving mode, connecting to sub-chip fails.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3302
Description:	Sub-chip initialization error (support number: 4801)
Causes:	When starting up the printer or returning from power saving mode, initialization of the sub-chip fails.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments. Memo: If the error occurred after reseating the flexible cables, check the condition of flexible cable connection.

Error code:	EC51 3303
Description:	Sub-chip firmware loading error (support number: 4801)
Causes:	When starting up the printer or returning from power saving mode, downloading sub-chip firmware fails.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3304
Description:	Media updating failure (support number: 4905)
Causes:	Updating the printer media information fails.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Update the printer media information with Media Configuration Tool. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3306
Description:	NAND file system initialization error (support number: 4905)
Causes:	When starting up the printer or returning from power saving mode, initialization of NAND file system fails.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3307
Description:	NAND file system unformatted (support number: 4905)
Causes:	When starting up the printer or returning from power saving mode, formatting of NAND file system fails.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3308
Description:	Checksum error at firmware update (support number: 4905)
Causes:	Checksum of the firmware sent at firmware updating does not match.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 3309
Description:	Memory allocation failure at firmware update (support number: 4905)
Causes:	Securing the operation area in RAM during firmware updating fails.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 330A
Description:	Firmware size error (support number: 4905)
Causes:	The size information described in the received firmware data and the actual received size does not match at firmware updating.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 4041
Description:	Deletion failure in main PCB SROM (support number: 6820) Memo: Remove the error in service mode when handling is completed.
Causes:	Deletion of the corresponding area in SROM during firmware updating fails.
Remedy:	1 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 4042
Description:	Writing failure in main PCB SROM (support number: 6820) Memo: Remove the error in service mode when handling is completed.
Causes:	Writing to SROM during firmware updating fails.
Remedy:	1 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 4045
Description:	Main PCB EEPROM error (support number: 6820) Memo: Remove the error in service mode when handling is completed.
Causes:	Abnormity is detected when information is written to the main PCB EEPROM.
Remedy:	1 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 4046
Description:	Main PCB failure in NAND flash deletion (support number: 6820) Memo: Remove the error in service mode when handling is completed.
Causes:	Deletion of the corresponding area in NAND flash during firmware updating fails.
Remedy:	1 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT (Disassembly & Reassembly for 24. model, for 36. model, for 44. model). • After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 4047
Description:	Writing failure in main PCB NAND flash (support number: 6820) Memo: Remove the error in service mode when handling is completed.
Causes:	Writing to NAND flash during firmware updating fails.
Remedy:	1 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 404C
Description:	Serial number data mismatch (support number: 6820) Memo: Remove the error in service mode when handling is completed.
Causes:	Mismatch of Serial number data in the BACKUP PCB UNIT and the MAIN PCB UNIT is detected in start-up of the printer.
Remedy:	1 This error occurs after MAIN PCB UNIT replacement Go to 2. This error occurs without performing MAIN PCB UNIT replacement Go to 3. 2 Start up the printer in service mode. Perform PCB replacement mode. (Automatic transformation from service mode to PCB replacement mode in start-up.) 3 Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments. The problem is resolved Complete. The problem is not resolved Put back the MAIN PCB UNIT, the one that has been installed before the replacement, and replace the BACKUP PCB UNIT.

Error code:	EC51 404D
Description:	Model ID mismatch (support number: 6820) Memo: Remove the error in service mode when handling is completed.
Causes:	When starting up the printer, model ID mismatch between MAIN PCB UNIT and BACKUP PCB UNIT is detected.
Remedy:	1 This error occurs after MAIN PCB UNIT replacement Go to 2. This error occurs without performing MAIN PCB UNIT replacement Go to 3. This error occurs after replacing to the BACKUP PCB UNIT that has been installed to the other model Replace with the new BACKUP PCB UNIT. 2 Start up the printer in service mode. Perform PCB replacement mode. (Automatic transformation from service mode to PCB replacement mode at starting up.) 3 Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments. The problem is resolved Complete. The problem is not resolved Put back the MAIN PCB UNIT, the one that has been installed before the replacement, and replace the BACKUP PCB UNIT.

Error code:	EC51 4070
Description:	Main PCB NAND flash ECC error (support number: 6820) Memo: Remove the error in service mode when handling is completed.
Causes:	ECC error in NAND flash occurs during firmware updating.
Remedy:	1 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 4071
Description:	Initialization failure in main PCB NAND flash (support number: 6820) Memo: Remove the error in service mode when handling is completed.
Causes:	When starting up the printer or returning from power saving mode, initialization of NAND flash fails.
Remedy:	1 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 4072
Description:	Format failure in Main PCB NAND flash (support number: 6820) Memo: Remove the error in service mode when handling is completed.
Causes:	When starting up the printer or returning from power saving mode, formatting of NAND flash fails.
Remedy:	1 Reinstall the firmware. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC51 5001
Description:	Start-up disabled (support number: 7050) Memo: Remove the error in service mode when handling is completed.
Causes:	Starting up the printer fails.
Remedy:	1 Check cable connection to the MAIN PCB UNIT. Proper connection Go to 2. Improper connection Connect the cable. 2 Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments. The problem is resolved Complete. The problem is not resolved Replace the ID PCB UNIT. (For how to order, ask sales companies in each region.)

Error code:	EC51 5002
Description:	Start-up disabled (support number: 7051) Memo: Remove the error in service mode when handling is completed.
Causes:	Starting up the printer fails.
Remedy:	1 Check cable connection to the MAIN PCB UNIT. Proper connection Go to 2. Improper connection Connect the cable. 2 Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments. The problem is resolved Complete. The problem is not resolved Replace the ID PCB UNIT. (For how to order, ask sales companies in each region.)

Error code:	EC51 5003
Description:	Start-up disabled (support number: 7052) Memo: Remove the error in service mode when handling is completed.
Causes:	Starting up the printer fails.
Remedy:	1 Check cable connection to the MAIN PCB UNIT. Proper connection Go to 2. Improper connection Connect the cable. 2 Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments. The problem is resolved Complete. The problem is not resolved Replace the ID PCB UNIT. (For how to order, ask sales companies in each region.)

Error code:	EC52 4038
Description:	Abnormal power supply voltage in standby or printing (support number: 9110) Memo: Remove the error in service mode when handling is completed.
Causes:	Power supply from the power supply unit stops in standby or printing.
Remedy:	1 Reconnect after unplugging the power cable from the AC outlet for ten seconds or longer. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Replace the POWER SUPPLY UNIT. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC52 4039
Description:	Abnormal power supply voltage in VH leak detection (support number: 9110) Memo: Remove the error in service mode when handling is completed.
Causes:	Power supply from the power supply unit stops in leak detection.
Remedy:	1 Reconnect after unplugging the power cable from the AC outlet for ten seconds or longer. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Replace the POWER SUPPLY UNIT. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC54 290A
Description:	Hard disk unconnected (support number: 4801)
Causes:	Hard disk detection at start-up fails.
Remedy:	1 Check if the hard disk cable is connected to the MAIN PCB UNIT. Connected Go to 2. Disconnected Connect the cable. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Replace the hard disk cable. The problem is resolved Complete. The problem is not resolved Go to 3. 3 Replace the POWER SUPPLY UNIT. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC54 290C
Description:	SED hard disk not initialized (support number: 4907)
Causes:	Unspecified SED hard disk settings is detected in starting up.
Remedy:	1 Reboot the printer. After rebooting, the message “initialize the hard disk?” appears on the control panel. Select “Yes” and perform format.* *This error is generated when selecting “No” to the above message.

Error code:	EC54 401A
Description:	Hard disk reading/writing error (support number: 7001) Memo: Remove the error in service mode when handling is completed.
Causes:	Reading/writing to the hard disk is disabled.
Remedy:	1 Replace the hard disk cable. The problem is resolved Complete. The problem is not resolved Go to 2. 2 Replace the hard disk. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC54 405A
Description:	Hard disk capacity mismatch (support number: 7003) Memo: Remove the error in service mode when handling is completed.
Causes:	Hard disk capacity difference is detected at start-up.
Remedy:	1 Replace the hard disk.

Error code:	EC54 405B
Description:	Hard disk model mismatch (support number: 7004) Memo: Remove the error in service mode when handling is completed.
Causes:	Hard disk model ID mismatch is detected at start-up.
Remedy:	1 Replace the hard disk.

Error code:	EC54 4080
Description:	Non-supported hard disk connected (support number: 7005) Memo: Remove the error in service mode after handling.
Causes:	Installation of SED hard disk was not detected.
Remedy:	1 Check the hard disk cable connection. Proper connection Go to 2. Improper connection Connect the cable. 2 Check if the SED hard disk (genuine) has been installed.* It is a genuine hard disk Replace MAIN PCB UNIT • . After replacement, perform PCB replacement mode and necessary adjustments. It is not a genuine hard disk Replace with a genuine SED hard disk. *When whether the cause is the SED hard disk or not cannot be identified clearly, replace with a genuine SED hard disk. (Disassembly & Reassembly for 24. model, for 36. model, for 44. model)

Error code:	EC54 4081
Description:	Hard disk SED function-related communication error (support number: 7006) .After replacement, perform PCB replacement mode and necessary adjustments.
Causes:	Performing the SED functioned command failed.
Remedy:	1 Check the hard disk cable connection. Proper connection Go to 2. Improper connection Connect the cable. 2 Replace the hard disk. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. .After replacement, perform PCB replacement mode and necessary adjustments. (Disassembly & Reassembly for 24. model, for 36. model, for 44. model)

Error code:	EC55 2F20
Description:	Flexible cable connection error (support number: 4801)
Causes:	Abnormity, left connection, or inappropriate connection in flexible cable connection between MAIN PCB UNIT and CARRIAGE UNIT was detected.
Remedy:	1 Check the flexible cable connection. Proper connection Replace the CARRIAGE UNIT. Improper connection Connect the flexible cable properly. The problem is not resolved Go to 2. 2 Reconnect the power cable after unplugging from the AC outlet for ten seconds or longer. The problem is resolved Complete. The problem is not resolved Replace the POWER SUPPLY UNIT.

Error code:	EC55 2F24
Description:	Flexible cable connected at an angle (support number: 1468)
Causes:	Flexible cable connection at an angle or non-connection is detected between MAIN PCB UNIT and CARRIAGE RELAY PCB UNIT.
Remedy:	1 Check the flexible cable connection. Proper connection Go to 2. Improper connection Connect the flexible cable properly. The problem is not resolved Go to 2. 2 Reconnect the power cable after unplugging from the AC outlet for ten seconds or longer. The problem is resolved Complete. The problem is not resolved Replace CARRIAGE UNIT. The problem is not resolved Replace POWER SUPPLY UNIT.

Error code:	EC55 2F6C
Description:	Print head temperature reading error (support number: 4801)
Causes:	Temperature reading by the direct diode sensor failed.
Remedy:	1 Check the flexible cable connection. Proper connection Go to 2. Improper connection Connect the flexible cable properly. The problem is not resolved Go to 2. 2 Replace with CARRIAGE UNIT. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC56 2FE0
Description:	Sub-ink tank unit power supply error (support number: 6502)
Causes:	The power is not supplied to ink tank ROMs.
Remedy:	1 Check the MAIN PCB UNIT cable connection. Proper connection Go to 2. Improper connection Connect the cable. 2 Check if the ink tank is empty. Not empty Replace the ink tank unit (replacement procedure for INK SUPPLY TANK UNIT L, for INK SUPPLY TANK UNIT R). Empty Replace the ink tank.

Error code:	EC57 4040
Description:	RTC time unknown (support number: 6702) Memo: Remove the error in service mode when handling is completed.
Causes:	Unset of GMT in RTC is detected at printer start-up in user mode.
Remedy:	1 Check if the battery is mounted in the MAIN PCB UNIT. Battery is mounted Replace the battery and set GMT time by [OTHERS>RTC SETTING] GMT. Battery is not mounted Remount the battery and set GMT time by [OTHERS>RTC SETTING]. GMT time = Greenwitch Mean Time

Error code:	EC57 404F
Description:	RTC non-connection (support number: 6700) Memo: Remove the error in service mode when handling is completed.
Causes:	Reading / writing to RTC data is disabled.
Remedy:	1 Reboot. The problem is resolved Complete. The problem is not resolved Replace MAIN PCB UNIT. After replacement, perform PCB replacement mode and necessary adjustments.

Error code:	EC58 2F12
Description:	Backup PCB EEPROM error (support number: 4801)
Causes:	Reading / writing to BACKUP PCB UNIT EEPROM is disabled.
Remedy:	1 Check the cable connection. Proper connection Replace the BACKUP PCB UNIT. Improper connection Connect the cable.

Error code:	EC59 3002
Description:	Wireless LAN device non-connection (support number: 6910)
Causes:	Wireless LAN device is not recognized.
Remedy:	1 Check the WIRELESS LAN PCB UNIT flexible cable connection Proper connection Replace the WIRELESS LAN PCB UNIT. Improper connection Connect the flexible cable.

Error code:	EC59 3003
Description:	Wireless LAN hardware error (support number: 6911)
Causes:	The wireless LAN device is physically broken.
Remedy:	1 Check the WIRELESS LAN PCB UNIT flexible cable connection Proper connection Replace the WIRELESS LAN PCB UNIT. Improper connection Connect the flexible cable.

Error code:	FF0000 2E3F
Description:	Paper feeding failure (other) (support number: 1300)
Causes:	Paper jam error other than above cases occurs.
Remedy:	1 Release the release lever. Reload the paper. (Check remained paper pieces and check the paper tip condition.) 2 Check other suspected cause. • Media related cause. (size, media type mismatch, turn-up at the tip of the paper) • Curly bottom tip of the roll paper. • Avoid the paper with strong stiffness or heavy roll paper.

Деталь:	CUT WASHER
Парткод:	QD1-1441-000

Деталь:	HOLDER, SPOOL SIDE R
Парткод:	QD1-1721-010

Деталь:	HOLDER, SPOOL SIDE L
Парткод:	QD1-1722-000

Деталь:	COVER, SPOOL R
Парткод:	QD1-1723-000

Деталь:	COVER, ROLL GEAR L
Парткод:	QD1-1792-000

Деталь:	CASE, SPOOL SIDE INNER R
Парткод:	QD1-2239-000

Деталь:	PAD, RELEASE LEVER STOPPER
Парткод:	QD1-2280-000

Деталь:	CAP, ROLL COVER SHAFT
Парткод:	QD1-2709-000

Деталь:	CAM, ROLL COVER SIDE
Парткод:	QD1-2863-000

Деталь:	PLATE UNIT, SPOOL SIDE SUPPORT
Парткод:	QM4-4907-000

Деталь:	DAMPER UNIT, ROLL COVER R
Парткод:	QM4-4908-000

Деталь:	IC, PHOTO INTERRUPTER
Парткод:	WG8-5935-000

Деталь:	SCREW, TP, WASHER HEAD, M3X12
Парткод:	XA9-1752-000

Деталь:	SCREW, TP, TRUSS HEAD, M4X10
Парткод:	XB4-7401-005

Деталь:	SCREW, FLANGED PAN HEAD, M3X4
Парткод:	XB6-7300-405

Деталь:	PAD, EJECT FRICTION
Парткод:	QD1-2435-000

Деталь:	SPRING, EJECT EARTH
Парткод:	QD1-2710-000

Деталь:	SPRING, EARTH
Парткод:	QD1-2888-000

Деталь:	CAM, FLAP SELEC
Парткод:	QD1-2595-000

Деталь:	LEVER, PAPER FEED SENSOR
Парткод:	QD1-2159-000

Деталь:	SPRING, PAPER FEED SENSOR
Парткод:	QD1-2160-000

Деталь:	ROLL PAPER FEED SENSOR UNIT
Парткод:	QM4-4249-010

Деталь:	PAPER GUIDE ROLLER UNIT, RU A
Парткод:	QM4-4859-000

Деталь:	PAPER GUIDE ROLLER UNIT, RU B
Парткод:	QM4-4860-000

Деталь:	FLAPPER SEPARATE UNIT
Парткод:	QM4-8718-000

Деталь:	HARNESS ASSY, LO FLAP SPLSET
Парткод:	QM7-4876-000

Деталь:	HARNESS ASSY, RU MAIN
Парткод:	QM7-4878-000

Деталь:	HARNESS ASSY, RLNIP PF SNS
Парткод:	QM7-4884-000

Деталь:	SCREW, HEX SOCKET M4X10
Парткод:	QC4-9300-000

Canon imagePROGRAF iPF TX-4000 MFP T36-AiO

Общие характеристики

Макс. формат

Размещение

Цветность печати

Факс

Телефон

Тип устройства

Сканер

Копир

Технология печати

Принтер

Количество цветов

Система непрерывной подачи чернил

Двусторонняя печать

Мин, объем капли

Печать без полей

Пигментные чернила

Прямая печать

Макс, разрешение для ч/б печати

Сканер

Отправка изображения по e-mail

Стандарт WIA

Слайд-адаптер

Стандарт TWAIN

Тип сканера

Макс. формат оригинала

Макс, размер сканирования

Разрешение сканера

Расходные материалы

Количество картриджей

Печать на:

Факс

Цветной

Телефон

Стандарт DECT

Беспроводная трубка

Проводная трубка

АОН

Языки управления

Финишер

Электронная сортировка

Брошюровщик

Сортер

Сортировка со сдвигом

Степлер

Интерфейсы

Wi-Fi 802.11n

Веб-интерфейс

Устройство для чтения карт памяти

Версия USB

Память/Процессор

Частота процессора

Емкость жесткого диска

Объем памяти

Дополнительная информация

Работа от аккумулятора

Диагональ дисплея

Экран

Поддержка ОС

Потребляемая мощность

Уровень шума

Габариты

Высота

Вес

Ширина

Глубина

Модули

Детали Upper Roll Unit, Suction Fan

Коды ошибок

Описание

Парткод

Название

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку

Деталь:	SCREW, MACHINE M8X16
Парткод:	XB7-1080-169

Деталь:	ROLL SEPARATE SENSOR UNIT
Парткод:	QM4-5357-000

Деталь:	HARNESS ASSY, LO ROLL SEP RLY
Парткод:	QM7-5412-000

Деталь:	HARNESS ASSY, ROLL SEP RLY
Парткод:	QM7-5404-000

Деталь:	FLAPPER SEPARATE UNIT W/SP
Парткод:	QM4-5867-000

Деталь:	PAPER GUIDE ROLLER UNIT, RU C
Парткод:	QM4-4861-000

Деталь:	COVER, INKTANK R INSIDE
Парткод:	QD1-2320-000

Деталь:	COVER, INKTANK L INSIDE
Парткод:	QC5-6189-000

Деталь:	HANDLE, INKTANK BACK
Парткод:	QD1-2553-000

Деталь:	COVER, INKTANK TOP BACK
Парткод:	QD1-2562-000