Canon imagePROGRAF iPF6200
Рейтинг
Снят с производства
Тип устройства
Принтер
Технология печати
пьезоэлектрическая струйная
Макс. формат
A1
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Печать фотографий |
|
Размещение |
напольный |
Тип устройства |
Принтер |
Цветность печати |
цветная |
Макс. формат |
A1 |
Копир |
|
Факс |
|
Телефон |
|
Сканер |
|
Технология печати |
пьезоэлектрическая струйная |
Тип |
струйный |
Принтер |
|
Количество цветов |
12 |
Печать без полей |
|
Пигментные чернила |
|
Мин, объем капли |
4 пл |
Макс. ширина рулона |
24 дюйм, (61 см) |
Двусторонняя печать |
|
Прямая печать |
|
Макс, разрешение для ч/б печати |
|
| По Y | 1 200 |
| По X | 1 200 |
| По X | 2 400 |
Сканер |
|
Стандарт WIA |
|
Отправка изображения по e-mail |
|
Стандарт TWAIN |
|
Печать на: |
|
| Глянцевой бумаге |
|
| Фотобумаге |
|
| Матовой бумаге |
|
| Рулоне |
|
| Пленках |
|
| CD/DVD |
|
| Конвертах |
|
| Этикетках |
|
Факс |
|
Цветной |
|
Телефон |
|
Стандарт DECT |
|
Спикерфон |
|
Проводная трубка |
|
Беспроводная трубка |
|
АОН |
|
Caller ID |
|
Автоответчик |
|
Языки управления |
|
| PostScript |
|
| PCL 5e |
|
| PCL 5c |
|
|
|
|
| PostScript 3 |
|
| PostScript 2 |
|
| PCL 6 |
|
| PPDS |
|
Финишер |
|
Электронная сортировка |
|
Сортер |
|
Сортировка со сдвигом |
|
Степлер |
|
Брошюровщик |
|
Интерфейсы |
|
Версия USB |
2,0 |
FireWire (IEEE 1394) |
|
Wi-Fi |
|
Bluetooth |
|
LPT |
|
Инфракрасный порт |
|
RS-232 |
|
Устройство для чтения карт памяти |
|
USB |
|
Ethernet (RJ-45) |
|
Память/Процессор |
|
Объем памяти |
384 |
Емкость жесткого диска |
80 |
Дополнительная информация |
|
Экран |
|
Поддержка ОС |
|
| Windows |
|
| Mac OS |
|
| DOS |
|
| Linux |
|
Потребляемая мощность |
|
| При работе | 100 |
| В режиме ожидания | 5 |
Уровень шума |
|
| При работе | 49 |
Габариты |
|
Вес |
51 |
Глубина |
893 |
Ширина |
1 177 |
Высота |
443 |
Модули
CARRIAGE UNIT
COVERS (2)
INK SUPPLY UNIT iPF6300S
PLATEN & SPUR UNIT
COVERS (1)
SPECTROPHOTOMETER FRAME
SPECTROPHOTOMETER ATTACHMENT
INK SUPPLY UNIT iPF6000S
Printer & Accessories
INK SUPPLY UNIT iPF6460/ 6450/ 6410/ 6400/ 6350/ 6300/6200/6100
PURGE UNIT
ROLL UNIT
CUTTER UNIT
STAND UNIT ST-29
AIR FLOW FAN UNIT
INK SUPPLY UNIT iPF6410SE/ 6400SE/ 605/ 605L plus
Stand Unit
Tool
PINCH ROLLER UNIT
CARRIAGE & FEED MOTOR UNIT
LINEAR SCALE & LIFT DRIVE UNIT
ELECTRICAL PART
INK SUPPLY UNIT iPF6410S/6400S
SPECTROPHOTOMETER COVERS
SPECTROPHOTOMETER MAIN
Детали INK SUPPLY UNIT iPF6410S/6400S
| Деталь: | CARRIAGE UNIT |
| Парткод: | QM3-0784-020 |
| Деталь: | CARRIAGE UNIT |
| Парткод: | QM3-9930-020 |
| Деталь: | CARRIAGE UNIT |
| Парткод: | QM3-0804-030 |
| Деталь: | CARRIAGE UNIT |
| Парткод: | QM4-8091-020 |
| Деталь: | CARRIAGE UNIT |
| Парткод: | QM4-8428-020 |
| Деталь: | FLEXIBLE CABLE ASSY |
| Парткод: | QM3-0786-010 |
| Деталь: | FLEXIBLE CABLE ASSY |
| Парткод: | QM3-0806-000 |
| Деталь: | BELT, CARRIAGE |
| Парткод: | QC2-0695-000 |
| Деталь: | BELT, CARRIAGE |
| Парткод: | QC2-4325-000 |
| Деталь: | CARRIAGE RELAY PCB ASSY |
| Парткод: | QM3-6448-000 |
| Деталь: | CARRIAGE RELAY PCB ASSY |
| Парткод: | QM3-0361-000 |
| Деталь: | CARRIAGE RELAY PCB ASSY |
| Парткод: | QM3-0351-000 |
| Деталь: | CARRIAGE RELAY PCB ASSY |
| Парткод: | QM7-7075-000 |
| Деталь: | CARRIAGE RELAY PCB ASSY |
| Парткод: | QM7-7239-000 |
| Деталь: | CABLE, FLEXIBLE |
| Парткод: | QK1-2090-000 |
| Деталь: | ENCODER SENSOR UNIT |
| Парткод: | QM2-3421-010 |
| Деталь: | MULTI SENSOR UNIT |
| Парткод: | QM3-0365-000 |
| Деталь: | MULTI SENSOR UNIT |
| Парткод: | QM2-3437-000 |
| Деталь: | MULTI SENSOR UNIT |
| Парткод: | QM4-8148-000 |
| Деталь: | HEAD LEVER UNIT |
| Парткод: | QM3-0541-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | QU1-2006-000 |
| Деталь: | HOLDER, BELT |
| Парткод: | QC2-4326-000 |
| Деталь: | COVER, FFC, MULTI-SENSOR |
| Парткод: | QC2-0710-000 |
| Деталь: | SPRIING, LEAF, GROUNDING |
| Парткод: | QC2-1283-000 |
| Деталь: | GUIDE, MULTI-SENSOR |
| Парткод: | QC2-1309-000 |
| Деталь: | CABLE, MULTI SENSOR |
| Парткод: | QK1 -2758-000 |
| Деталь: | CABLE, MULTI SENSOR |
| Парткод: | QK1-2757-000 |
| Деталь: | CABLE, MULTI SENSOR |
| Парткод: | QK1 -9587-000 |
| Деталь: | CABLE, FLAT, MULTI-SENSOR |
| Парткод: | QK1-2091-000 |
| Деталь: | FERRITE CORE |
| Парткод: | WE8-6409-000 |
| Деталь: | HOLDER, WIRE(MECH) |
| Парткод: | QC2-0663-000 |
| Деталь: | LEVER, L, INK TUBE |
| Парткод: | QD1-0405-000 |
| Деталь: | LINK, LEVER, TUBE |
| Парткод: | QC2-0661-000 |
| Деталь: | PAD, OIL |
| Парткод: | QC2-0664-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QC2-1396-000 |
| Деталь: | CLEANER UNIT, R, RAIL, CARRIAGE |
| Парткод: | QM3-0543-000 |
| Деталь: | CLEANER UNIT, L, RAIL, CARRIAGE |
| Парткод: | QM3-0542-000 |
| Деталь: | HOLDER, LEVER SET, PRINTHEAD |
| Парткод: | QC2-0653-000 |
| Деталь: | HEAD LEVER UNIT |
| Парткод: | QM3-0560-000 |
| Деталь: | LEVER, R, INK TUBE |
| Парткод: | QD1-0404-000 |
| Деталь: | TUBE GUIDE UNIT |
| Парткод: | QM3-0704-000 |
| Деталь: | RETAINER, OIL PAD |
| Парткод: | QC2-0665-000 |
| Деталь: | COVER, REAR, UPPER |
| Парткод: | QC2-1120-010 |
| Деталь: | COVER, LEFT, REAR |
| Парткод: | QC2-1124-050 |
| Деталь: | COVER, LEFT, REAR |
| Парткод: | QC2-1140-000 |
| Деталь: | COVER, REAR |
| Парткод: | QC2-1172-000 |
| Деталь: | COVER, REAR, LOWER |
| Парткод: | QL2-1588-000 |
| Деталь: | COVER, BOTTOM, RIGHT |
| Парткод: | QM3-0561-040 |
| Деталь: | COVER, BOTTOM, RIGHT |
| Парткод: | QM3-0547-050 |
| Деталь: | COVER, BOTTOM, LEFT |
| Парткод: | QM3-0706-000 |
| Деталь: | COVER, BOTTOM, LEFT |
| Парткод: | QM3-0548-040 |
| Деталь: | COVER, BOTTOM, LEFT |
| Парткод: | QM4-8061-000 |
| Деталь: | GUIDE, PAPER, MANUAL FEED |
| Парткод: | QC2-1118-000 |
| Деталь: | COVER, REAR, LEFT |
| Парткод: | QC2-1154-000 |
| Деталь: | COVER, REAR, L |
| Парткод: | QC2-0946-000 |
| Деталь: | COVER, REAR, R |
| Парткод: | QC2-6071-000 |
| Деталь: | COVER, BOTTOM |
| Парткод: | QC2-6249-000 |
| Деталь: | COVER, BOTTOM, SUB |
| Парткод: | QC2-6250-000 |
| Деталь: | LABEL, SCALE |
| Парткод: | QC2-6575-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-5295-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-0568-050 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-0775-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-9918-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-6679-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8090-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8366-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8418-000 |
| Деталь: | GUIDE, TUBE, CARRIAGE |
| Парткод: | QC2-0746-020 |
| Деталь: | IC, PHOTO INTERRUPTER, TLP1241 |
| Парткод: | WG8-5624-000 |
| Деталь: | BASE UNIT, JOINT |
| Парткод: | QM3-0584-000 |
| Деталь: | JOINT BASE UNIT |
| Парткод: | QM3-0699-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM3-5302-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM3-0162-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8096-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8097-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8414-000 |
| Деталь: | GEAR, VALVE 2 |
| Парткод: | QC2-0739-000 |
| Деталь: | GEAR, VALVE 3 |
| Парткод: | QC2-0740-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QC2-8591-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QC2-0742-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-1148-000 |
| Деталь: | BELT, TIMING |
| Парткод: | QC2-0832-000 |
| Деталь: | MOTOR, UNDER 10W, DC |
| Парткод: | QK1 -0550-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QC2-0763-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QD1-0257-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QD1-1151-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QC2-0764-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QD1-0256-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QD1-1150-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0368-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0862-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7084-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7231-000 |
| Деталь: | GUIDE, INK TUBE |
| Парткод: | QC2-1375-000 |
| Деталь: | GUIDE, INK TUBE |
| Парткод: | QD1-0307-000 |
| Деталь: | GUIDE, TUBE |
| Парткод: | QC2-6346-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-5294-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-0574-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-9919-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-6488-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM4-8020-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM4-8367-010 |
| Деталь: | HARNESS, WIRE, FEED |
| Парткод: | QM3-0928-000 |
| Деталь: | HARNESS, WIRE, FEED |
| Парткод: | QM7-7252-000 |
| Деталь: | JOINT, LEVER |
| Парткод: | QC2-0758-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0855-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0369-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7083-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7230-000 |
| Деталь: | HARNESS, WIRE, ROM, INK TANK |
| Парткод: | QM3-0903-000 |
| Деталь: | HARNESS, WIRE, ROM, INK TANK |
| Парткод: | QM3-0875-000 |
| Деталь: | HARNESS, WIRE, SENSOR, VALVE |
| Парткод: | QM3-0914-000 |
| Деталь: | HARNESS, WIRE, SENSOR, VALVE |
| Парткод: | QM3-0886-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM3-0901-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM3-0872-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM7-7082-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM7-7256-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0947-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0882-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0924-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM7-7080-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM7-7253-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM3-0884-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM3-0925-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM7-7081-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM7-7254-000 |
| Деталь: | INK TUBE UNIT (L) |
| Парткод: | QM3-5296-000 |
| Деталь: | INK TUBE UNIT (L) |
| Парткод: | QM3-9920-000 |
| Деталь: | INK TUBE UNIT (R) |
| Парткод: | QM3-5297-000 |
| Деталь: | INK TUBE UNIT (R) |
| Парткод: | QM3-9921-000 |
| Деталь: | WASHER |
| Парткод: | QC1-4149-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-0269-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-1060-000 |
| Деталь: | GEAR, VALVE |
| Парткод: | QD1-0270-000 |
| Деталь: | LEVER, TENSION |
| Парткод: | QD1-0271-000 |
| Деталь: | ROLLER, TENSION |
| Парткод: | QD1-0272-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QD1-0273-000 |
| Деталь: | SHAFT |
| Парткод: | QD1-0274-000 |
| Деталь: | PULLEY, BELT |
| Парткод: | QD1-0298-000 |
| Деталь: | PHOTO-INTERRUPTER, SG2481 |
| Парткод: | WG8-5776-000 |
| Деталь: | HARNESS, VALVE UNIT |
| Парткод: | QM7-7232-000 |
| Деталь: | HARNESS, VALVE, RELAY |
| Парткод: | QM7-7233-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | SPUR UNIT |
| Парткод: | QM3-6675-000 |
| Деталь: | SPUR UNIT |
| Парткод: | QM3-0793-010 |
| Деталь: | SPUR MOTOR UNIT |
| Парткод: | QM3-0246-000 |
| Деталь: | PLATEN A |
| Парткод: | QL2-1579-000 |
| Деталь: | PLATEN B |
| Парткод: | QL2-1580-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5624-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QA4-0292-000 |
| Деталь: | ROWEL |
| Парткод: | QA4-0880-000 |
| Деталь: | BUSHING |
| Парткод: | QC2-0866-000 |
| Деталь: | BELT, DRIVE, PAPER EJECTION |
| Парткод: | QC2-0958-000 |
| Деталь: | PULLEY |
| Парткод: | QC2-0964-000 |
| Деталь: | RING |
| Парткод: | QC2-1395-000 |
| Деталь: | PULLEY, BELT |
| Парткод: | QC2-1569-000 |
| Деталь: | WASHER |
| Парткод: | QC1-4149-000 |
| Деталь: | BUSHING |
| Парткод: | QC2-1002-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QC2-1396-000 |
| Деталь: | SENSOR UNIT, SPUR |
| Парткод: | QM3-0245-000 |
| Деталь: | COVER, BUSHING |
| Парткод: | QC2-1007-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | QC2-1009-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QC2-1018-000 |
| Деталь: | GEAR, ROWEL |
| Парткод: | QC2-1024-000 |
| Деталь: | ARM, SUPPORT, ROWEL BASE |
| Парткод: | QC2-1025-000 |
| Деталь: | CAM, ROWEL |
| Парткод: | QC2-1027-000 |
| Деталь: | PLATE, REFLECTION, MULTI-SENSOR |
| Парткод: | QL2-2423-000 |
| Деталь: | PLATE, REFLECTION, MULTI-SENSOR |
| Парткод: | QL2-1561-000 |
| Деталь: | PLATE, REFLECTION, MULTI-SENSOR |
| Парткод: | QL2-8032-000 |
| Деталь: | DUCT UNIT, PLATEN |
| Парткод: | QM3-0800-000 |
| Деталь: | DUCT UNIT, PLATEN |
| Парткод: | QM3-0801-000 |
| Деталь: | PLATEN C |
| Парткод: | QL2-1581-000 |
| Деталь: | FLANGE, BELT PULLEY |
| Парткод: | QC2-1570-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | QL2-1567-000 |
| Деталь: | GUIDE, WASTE INK |
| Парткод: | QC2-0811-000 |
| Деталь: | GUIDE, MULTI-SENSOR |
| Парткод: | QD1-0315-000 |
| Деталь: | COVER, CIRCLE |
| Парткод: | QC2-8605-000 |
| Деталь: | COVER, CIRCLE |
| Парткод: | QC2-1165-000 |
| Деталь: | COVER, CIRCLE |
| Парткод: | QC2-8643-000 |
| Деталь: | COVER, CIRCLE |
| Парткод: | QD1-1039-000 |
| Деталь: | TANK COVER UNIT |
| Парткод: | QM3-5305-000 |
| Деталь: | TANK COVER UNIT |
| Парткод: | QM3-0762-000 |
| Деталь: | TANK COVER UNIT |
| Парткод: | QM3-0708-000 |
| Деталь: | TANK COVER UNIT |
| Парткод: | QM3-6680-000 |
| Деталь: | TANK COVER UNIT |
| Парткод: | QM3-9915-000 |
| Деталь: | TANK COVER UNIT |
| Парткод: | QM4-8065-000 |
| Деталь: | TANK COVER UNIT |
| Парткод: | QM4-8363-000 |
| Деталь: | TANK COVER UNIT |
| Парткод: | QM4-8389-000 |
| Деталь: | TANK COVER UNIT |
| Парткод: | QM4-8406-000 |
| Деталь: | COVER, LEFT |
| Парткод: | QC2-1123-000 |
| Деталь: | COVER, LEFT |
| Парткод: | QD1-0236-000 |
| Деталь: | FRONT COVER UNIT |
| Парткод: | QC2-1139-030 |
| Деталь: | FRONT COVER UNIT |
| Парткод: | QC2-1122-000 |
| Деталь: | FRONT COVER UNIT |
| Парткод: | QM4-8062-000 |
| Деталь: | FRONT COVER UNIT |
| Парткод: | QM4-8404-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QC2-8599-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QC2-8562-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QC2-1458-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QC2-8598-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QC2-8639-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QC3-2679-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QC4-0917-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QD1-0319-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QD1-0320-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QD1-0464-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QD1-0465-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QD1-1052-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QD1-1053-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QD1-1108-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QD1-1133-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QD1-1145-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QC3-2875-000 |
| Деталь: | GUIDE, PICK-UP, RIGHT, 2 |
| Парткод: | QC2-6315-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM3-5306-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM3-5307-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM3-4340-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM3-4339-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM3-0729-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM3-0718-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM3-5318-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM3-5317-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM3-9916-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM3-9917-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM4-8394-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM4-8408-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM4-8409-000 |
| Деталь: | MIST FILTER UNIT |
| Парткод: | QM3-0212-030 |
| Деталь: | COVER, FILTER |
| Парткод: | QC2-1167-000 |
| Деталь: | COVER, RIGHT |
| Парткод: | QM3-0583-030 |
| Деталь: | COVER, RIGHT |
| Парткод: | QM3-0614-030 |
| Деталь: | COVER, LOUVER |
| Парткод: | QC2-1272-000 |
| Деталь: | COVER, RIGHT, FRONT |
| Парткод: | QL2-2404-000 |
| Деталь: | COVER, RIGHT, FRONT |
| Парткод: | QL2-2387-000 |
| Деталь: | TOP COVER UNIT |
| Парткод: | QM3-5304-000 |
| Деталь: | TOP COVER UNIT |
| Парткод: | QM3-0737-030 |
| Деталь: | TOP COVER UNIT |
| Парткод: | QM3-6681-010 |
| Деталь: | TOP COVER UNIT |
| Парткод: | QM3-9914-010 |
| Деталь: | TOP COVER UNIT |
| Парткод: | QM4-8069-010 |
| Деталь: | TOP COVER UNIT |
| Парткод: | QM4-8364-000 |
| Деталь: | TOP COVER UNIT |
| Парткод: | QM4-8393-000 |
| Деталь: | TOP COVER UNIT |
| Парткод: | QM4-8407-000 |
| Деталь: | COVER, FRONT, UPPER |
| Парткод: | QC2-1391-000 |
| Деталь: | COVER, FRONT, UPPER |
| Парткод: | QC2-1307-000 |
| Деталь: | COVER, FRONT, UPPER |
| Парткод: | QD1-1107-000 |
| Деталь: | HOLDER, FILTER(MECH), EXHAUST |
| Парткод: | QL2-1555-000 |
| Деталь: | COVER, AIR DUCT, FRONT |
| Парткод: | QC2-1270-000 |
| Деталь: | ARM |
| Парткод: | QC2-1273-000 |
| Деталь: | FILTER(MECH), INK MIST |
| Парткод: | QC2-1103-000 |
| Деталь: | ABSORBER, DRAIN, WASTE INK |
| Парткод: | QC2-1446-000 |
| Деталь: | COVER, BLANKING |
| Парткод: | QC2-6275-000 |
| Деталь: | DELIVERY GUIDE UNIT |
| Парткод: | QM3-0700-000 |
| Деталь: | GUIDE, PICK-UP, 1 |
| Парткод: | QC2-6265-000 |
| Деталь: | SUPPORT, PICK-UP GUIDE |
| Парткод: | QC2-6266-000 |
| Деталь: | GUIDE, PICK-UP, 2 |
| Парткод: | QC2-6302-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QC2-6303-000 |
| Деталь: | GUIDE, PICK-UP, RIGHT, 1 |
| Парткод: | QC2-6308-000 |
| Деталь: | EMBLEM, CANON LOGO |
| Парткод: | QC2-6663-000 |
| Деталь: | EMBLEM, CANON LOGO |
| Парткод: | QC2-1404-000 |
| Деталь: | EMBLEM, CANON LOGO |
| Парткод: | QC2-8645-000 |
| Деталь: | EMBLEM, CANON LOGO |
| Парткод: | QD1-1041-000 |
| Деталь: | TOP COVER UNIT, L |
| Парткод: | QM4-8405-000 |
| Деталь: | COVER, TOP, LEFT |
| Парткод: | QM4-8063-000 |
| Деталь: | DELIVERY GUIDE UNIT |
| Парткод: | QM4-8413-000 |
| Деталь: | SHEET, EJECT GUIDE |
| Парткод: | QD1-0485-000 |
| Деталь: | GEAR, 22T/88T |
| Парткод: | QD1-0117-000 |
| Деталь: | GEAR, 30T |
| Парткод: | QD1-0118-000 |
| Деталь: | GUIDE, SLIDER, R |
| Парткод: | QD1-0135-000 |
| Деталь: | GUIDE, SLIDER, L |
| Парткод: | QD1-0136-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | QD1-0138-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | QD1-0144-000 |
| Деталь: | SPRING, TORSION, R |
| Парткод: | QD1-0147-000 |
| Деталь: | SPRING, TORSION, L |
| Парткод: | QD1-0148-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | QD1-0153-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | QD1-0154-000 |
| Деталь: | BELT |
| Парткод: | QD1-0188-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QD1-0189-000 |
| Деталь: | GUARD, EDGE |
| Парткод: | QD1-0200-000 |
| Деталь: | COVER, USB |
| Парткод: | QD1-0206-000 |
| Деталь: | COVER, ARM, LEFT |
| Парткод: | QD1-0213-000 |
| Деталь: | SUPPORT, SPRING, B |
| Парткод: | QD1-0488-000 |
| Деталь: | SUPPORT, SPRING, C |
| Парткод: | QD1-0489-000 |
| Деталь: | SUPPORT, LIFT SPRING |
| Парткод: | QD1-0490-000 |
| Деталь: | SHEET, ARM COVER, RIGHT |
| Парткод: | QD1-0495-000 |
| Деталь: | SHEET, ARM COVER, LEFT |
| Парткод: | QD1-0496-000 |
| Деталь: | ROLLER |
| Парткод: | QE1-3177-000 |
| Деталь: | SHAFT |
| Парткод: | QE1-3210-000 |
| Деталь: | LIFT MOTOR UNIT |
| Парткод: | QM4-8093-000 |
| Деталь: | LIFT DRIVE UNIT |
| Парткод: | QM4-8052-010 |
| Деталь: | COVER, ARM, RIGHT |
| Парткод: | QM4-8089-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM7-7078-000 |
| Деталь: | HARNESS, WIRE, CM MAIN |
| Парткод: | QM7-7088-000 |
| Деталь: | PHOTO-INTERRUPTER, SG2481 |
| Парткод: | WG8-5776-000 |
| Деталь: | SCREW, W/WASHER, M3X8 |
| Парткод: | XA9-1420-000 |
| Цена: | 1 100 ₽ |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, TP, M3X8 |
| Парткод: | XA9-1928-000 |
| Деталь: | SCREW, STEPPED, M4 |
| Парткод: | QC1-7399-000 |
| Деталь: | SCREW, HEX SOCKET M4X10 |
| Парткод: | QC2-4116-000 |
| Деталь: | SCREW, STEPPED, M4 |
| Парткод: | QC3-0133-000 |
| Деталь: | ROD, SIDE AL |
| Парткод: | QC3-1455-000 |
| Деталь: | GUIDE, BASKET |
| Парткод: | QC3-1492-000 |
| Деталь: | SUPPORT, ROD |
| Парткод: | QC3-1739-000 |
| Деталь: | PROTECTOR, ROD |
| Парткод: | QC3-1850-000 |
| Деталь: | HOLDER, ROD SUPPORT |
| Парткод: | QD1-0171-000 |
| Деталь: | ATTACHMENT, ARM |
| Парткод: | QD1-0173-000 |
| Деталь: | GUIDE, STAND LEFT |
| Парткод: | QD1-0174-000 |
| Деталь: | GUIDE, STAND RIGHT |
| Парткод: | QD1-0175-000 |
| Деталь: | COVER, CABLE |
| Парткод: | QD1-0195-000 |
| Деталь: | HARNESS, PRINTER IF, RELAY 1 |
| Парткод: | QM7-7094-000 |
| Деталь: | HARNESS, PRINTER IF, RELAY 2 |
| Парткод: | QM7-7095-000 |
| Деталь: | SCREW, M4X8 |
| Парткод: | XA9-0893-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-5295-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-0568-050 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-0775-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-9918-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-6679-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8090-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8366-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8418-000 |
| Деталь: | GUIDE, TUBE, CARRIAGE |
| Парткод: | QC2-0746-020 |
| Деталь: | IC, PHOTO INTERRUPTER, TLP1241 |
| Парткод: | WG8-5624-000 |
| Деталь: | BASE UNIT, JOINT |
| Парткод: | QM3-0584-000 |
| Деталь: | JOINT BASE UNIT |
| Парткод: | QM3-0699-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM3-5302-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM3-0162-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8096-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8097-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8414-000 |
| Деталь: | GEAR, VALVE 2 |
| Парткод: | QC2-0739-000 |
| Деталь: | GEAR, VALVE 3 |
| Парткод: | QC2-0740-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QC2-8591-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QC2-0742-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-1148-000 |
| Деталь: | BELT, TIMING |
| Парткод: | QC2-0832-000 |
| Деталь: | MOTOR, UNDER 10W, DC |
| Парткод: | QK1 -0550-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QC2-0763-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QD1-0257-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QD1-1151-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QC2-0764-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QD1-0256-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QD1-1150-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0368-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0862-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7084-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7231-000 |
| Деталь: | GUIDE, INK TUBE |
| Парткод: | QC2-1375-000 |
| Деталь: | GUIDE, INK TUBE |
| Парткод: | QD1-0307-000 |
| Деталь: | GUIDE, TUBE |
| Парткод: | QC2-6346-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-5294-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-0574-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-9919-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-6488-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM4-8020-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM4-8367-010 |
| Деталь: | HARNESS, WIRE, FEED |
| Парткод: | QM3-0928-000 |
| Деталь: | HARNESS, WIRE, FEED |
| Парткод: | QM7-7252-000 |
| Деталь: | JOINT, LEVER |
| Парткод: | QC2-0758-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0855-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0369-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7083-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7230-000 |
| Деталь: | HARNESS, WIRE, ROM, INK TANK |
| Парткод: | QM3-0903-000 |
| Деталь: | HARNESS, WIRE, ROM, INK TANK |
| Парткод: | QM3-0875-000 |
| Деталь: | HARNESS, WIRE, SENSOR, VALVE |
| Парткод: | QM3-0914-000 |
| Деталь: | HARNESS, WIRE, SENSOR, VALVE |
| Парткод: | QM3-0886-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM3-0901-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM3-0872-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM7-7082-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM7-7256-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0947-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0882-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0924-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM7-7080-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM7-7253-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM3-0884-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM3-0925-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM7-7081-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM7-7254-000 |
| Деталь: | INK TUBE UNIT (L) |
| Парткод: | QM3-5296-000 |
| Деталь: | INK TUBE UNIT (L) |
| Парткод: | QM3-9920-000 |
| Деталь: | INK TUBE UNIT (R) |
| Парткод: | QM3-5297-000 |
| Деталь: | INK TUBE UNIT (R) |
| Парткод: | QM3-9921-000 |
| Деталь: | WASHER |
| Парткод: | QC1-4149-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-0269-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-1060-000 |
| Деталь: | GEAR, VALVE |
| Парткод: | QD1-0270-000 |
| Деталь: | LEVER, TENSION |
| Парткод: | QD1-0271-000 |
| Деталь: | ROLLER, TENSION |
| Парткод: | QD1-0272-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QD1-0273-000 |
| Деталь: | SHAFT |
| Парткод: | QD1-0274-000 |
| Деталь: | PULLEY, BELT |
| Парткод: | QD1-0298-000 |
| Деталь: | PHOTO-INTERRUPTER, SG2481 |
| Парткод: | WG8-5776-000 |
| Деталь: | HARNESS, VALVE UNIT |
| Парткод: | QM7-7232-000 |
| Деталь: | HARNESS, VALVE, RELAY |
| Парткод: | QM7-7233-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | PRINTHEAD |
| Парткод: | NPN |
| Деталь: | INK TANK (MBK) |
| Парткод: | NPN |
| Деталь: | INK TANK (PBK) |
| Парткод: | NPN |
| Деталь: | INK TANK (C) |
| Парткод: | NPN |
| Деталь: | INK TANK (M) |
| Парткод: | NPN |
| Деталь: | INK TANK (Y) |
| Парткод: | NPN |
| Деталь: | INK TANK (PC) |
| Парткод: | NPN |
| Деталь: | INK TANK (PM) |
| Парткод: | NPN |
| Деталь: | INK TANK (R) |
| Парткод: | NPN |
| Деталь: | INK TANK (G) |
| Парткод: | NPN |
| Деталь: | INK TANK (B) |
| Парткод: | NPN |
| Деталь: | INK TANK (GY) |
| Парткод: | NPN |
| Деталь: | INK TANK (PGY) |
| Парткод: | NPN |
| Деталь: | STOPPER, BELT |
| Парткод: | QC2-1397-020 |
| Деталь: | BRUSH, CLEANING |
| Парткод: | QC3-0169-000 |
| Деталь: | BRUSH, CLEANER |
| Парткод: | FB1-0733-000 |
| Деталь: | CORD, POWER |
| Парткод: | QK1 -2688-000 |
| Деталь: | CORD, POWER |
| Парткод: | QK1 -2689-000 |
| Деталь: | CORD, POWER |
| Парткод: | QK1 -2685-020 |
| Деталь: | CORD, POWER |
| Парткод: | QK1 -2682-000 |
| Деталь: | CORD, POWER |
| Парткод: | QK1 -2690-010 |
| Деталь: | CORD, POWER |
| Парткод: | QK1-2686-000 |
| Деталь: | WIRE, GROUND |
| Парткод: | FH2-7092-020 |
| Деталь: | WRENCH |
| Парткод: | QC2-4361-000 |
| Деталь: | WRENCH, HEX KEY |
| Парткод: | QC2-4362-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-5295-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-0568-050 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-0775-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-9918-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-6679-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8090-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8366-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8418-000 |
| Деталь: | GUIDE, TUBE, CARRIAGE |
| Парткод: | QC2-0746-020 |
| Деталь: | IC, PHOTO INTERRUPTER, TLP1241 |
| Парткод: | WG8-5624-000 |
| Деталь: | BASE UNIT, JOINT |
| Парткод: | QM3-0584-000 |
| Деталь: | JOINT BASE UNIT |
| Парткод: | QM3-0699-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM3-5302-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM3-0162-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8096-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8097-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8414-000 |
| Деталь: | GEAR, VALVE 2 |
| Парткод: | QC2-0739-000 |
| Деталь: | GEAR, VALVE 3 |
| Парткод: | QC2-0740-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QC2-8591-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QC2-0742-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-1148-000 |
| Деталь: | BELT, TIMING |
| Парткод: | QC2-0832-000 |
| Деталь: | MOTOR, UNDER 10W, DC |
| Парткод: | QK1 -0550-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QC2-0763-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QD1-0257-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QD1-1151-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QC2-0764-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QD1-0256-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QD1-1150-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0368-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0862-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7084-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7231-000 |
| Деталь: | GUIDE, INK TUBE |
| Парткод: | QC2-1375-000 |
| Деталь: | GUIDE, INK TUBE |
| Парткод: | QD1-0307-000 |
| Деталь: | GUIDE, TUBE |
| Парткод: | QC2-6346-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-5294-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-0574-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-9919-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-6488-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM4-8020-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM4-8367-010 |
| Деталь: | HARNESS, WIRE, FEED |
| Парткод: | QM3-0928-000 |
| Деталь: | HARNESS, WIRE, FEED |
| Парткод: | QM7-7252-000 |
| Деталь: | JOINT, LEVER |
| Парткод: | QC2-0758-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0855-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0369-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7083-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7230-000 |
| Деталь: | HARNESS, WIRE, ROM, INK TANK |
| Парткод: | QM3-0903-000 |
| Деталь: | HARNESS, WIRE, ROM, INK TANK |
| Парткод: | QM3-0875-000 |
| Деталь: | HARNESS, WIRE, SENSOR, VALVE |
| Парткод: | QM3-0914-000 |
| Деталь: | HARNESS, WIRE, SENSOR, VALVE |
| Парткод: | QM3-0886-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM3-0901-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM3-0872-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM7-7082-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM7-7256-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0947-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0882-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0924-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM7-7080-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM7-7253-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM3-0884-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM3-0925-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM7-7081-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM7-7254-000 |
| Деталь: | INK TUBE UNIT (L) |
| Парткод: | QM3-5296-000 |
| Деталь: | INK TUBE UNIT (L) |
| Парткод: | QM3-9920-000 |
| Деталь: | INK TUBE UNIT (R) |
| Парткод: | QM3-5297-000 |
| Деталь: | INK TUBE UNIT (R) |
| Парткод: | QM3-9921-000 |
| Деталь: | WASHER |
| Парткод: | QC1-4149-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-0269-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-1060-000 |
| Деталь: | GEAR, VALVE |
| Парткод: | QD1-0270-000 |
| Деталь: | LEVER, TENSION |
| Парткод: | QD1-0271-000 |
| Деталь: | ROLLER, TENSION |
| Парткод: | QD1-0272-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QD1-0273-000 |
| Деталь: | SHAFT |
| Парткод: | QD1-0274-000 |
| Деталь: | PULLEY, BELT |
| Парткод: | QD1-0298-000 |
| Деталь: | PHOTO-INTERRUPTER, SG2481 |
| Парткод: | WG8-5776-000 |
| Деталь: | HARNESS, VALVE UNIT |
| Парткод: | QM7-7232-000 |
| Деталь: | HARNESS, VALVE, RELAY |
| Парткод: | QM7-7233-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | GUIDE, MAINTENANCE CARTRIDGE |
| Парткод: | QC2-1110-000 |
| Деталь: | GUIDE, MAINTENANCE CARTRIDGE |
| Парткод: | QD1-0137-010 |
| Деталь: | HARNESS, WIRE, HEAD MANAGEMENT |
| Парткод: | QM3-0904-000 |
| Деталь: | HARNESS, WIRE, HEAD MANAGEMENT |
| Парткод: | QM3-0876-000 |
| Деталь: | JOINT, TUBE |
| Парткод: | QC2-1323-000 |
| Деталь: | PURGE KIT |
| Парткод: | QM3-0653-090 |
| Деталь: | PURGE KIT |
| Парткод: | QM3-0654-070 |
| Деталь: | PURGE KIT |
| Парткод: | QM4-8427-000 |
| Деталь: | PURGE KIT |
| Парткод: | QM3-8145-040 |
| Деталь: | HEAD MANAGEMENT SENSOR |
| Парткод: | QM3-0529-000 |
| Деталь: | ABSORBER, INK, FAN |
| Парткод: | QC2-1100-000 |
| Деталь: | ABSORBER, WASTE INK |
| Парткод: | QC2-0807-000 |
| Деталь: | JOINT, INK TUBE, PURGE UNIT |
| Парткод: | QC2-0833-020 |
| Деталь: | MIST FAN UNIT |
| Парткод: | QM3-0799-000 |
| Деталь: | MIST FAN UNIT |
| Парткод: | QM3-0807-000 |
| Деталь: | FAN |
| Парткод: | QK1-2086-000 |
| Деталь: | FAN |
| Парткод: | QK1-2087-000 |
| Деталь: | W-INK TUBE, COLOR |
| Парткод: | QC3-2881-000 |
| Деталь: | W-INK TUBE, BLACK |
| Парткод: | QC3-5565-000 |
| Деталь: | TUBE JOINT UNIT |
| Парткод: | QM3-6676-000 |
| Деталь: | JOINT, INK TUBE, PURGE UNIT |
| Парткод: | QC3-2876-000 |
| Деталь: | ABSORBER, SUB CAP |
| Парткод: | QC2-1440-000 |
| Деталь: | ABSORBER, CAP |
| Парткод: | QC3-2850-000 |
| Деталь: | COVER, ROLL |
| Парткод: | QC2-1256-050 |
| Деталь: | COVER, ROLL |
| Парткод: | QD1-1170-000 |
| Деталь: | COVER, ROLL, LEFT |
| Парткод: | QC2-1385-000 |
| Деталь: | COVER, ROLL, RIGHT |
| Парткод: | QC2-1386-000 |
| Деталь: | TRAY, MANUAL PAPER FEED |
| Парткод: | QC2-6261-000 |
| Деталь: | GUIDE, SIDE, PAPER |
| Парткод: | QC2-1261-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | QC2-1262-000 |
| Деталь: | SLIDE PIECE, GUIDE |
| Парткод: | QC2-1310-000 |
| Деталь: | HOLDER, ROLL |
| Парткод: | QC2-1222-000 |
| Деталь: | SCREW, MACHINE, RS-TIGHT, M3X6 |
| Парткод: | XA9-0863-000 |
| Деталь: | SPACER, HOLDER, ROLL |
| Парткод: | QC2-1223-000 |
| Деталь: | ROLL SHAFT UNIT |
| Парткод: | QM3-0715-000 |
| Деталь: | CAP, ROLL, LEFT |
| Парткод: | QC4-0930-000 |
| Деталь: | CAP, ROLL, LEFT |
| Парткод: | QC2-1263-000 |
| Деталь: | CAP, ROLL, RIGHT |
| Парткод: | QC2-1264-000 |
| Деталь: | CAP, ROLL, RIGHT |
| Парткод: | QC4-0931-000 |
| Деталь: | CASE, ROLL, LEFT |
| Парткод: | QC2-1257-000 |
| Деталь: | CASE, ROLL, RIGHT |
| Парткод: | QC2-1258-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | QK1 -2081-000 |
| Деталь: | PCB ASSY, DRIVER, ROLL UNIT |
| Парткод: | QM2-3428-010 |
| Деталь: | HOLDER UNIT, LEFT, ROLL HOLDER |
| Парткод: | QM3-0226-000 |
| Деталь: | HOLDER UNIT, RIGHT, ROLL HOLDER |
| Парткод: | QM3-0227-000 |
| Деталь: | ROLLER RELEASE UNIT |
| Парткод: | QM3-0719-000 |
| Деталь: | SENSOR UNIT, DETECTION, ROLL |
| Парткод: | QM3-0231-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5624-000 |
| Деталь: | FEED ROLLER UNIT |
| Парткод: | QM3-0721-000 |
| Деталь: | BUSHING |
| Парткод: | QC2-1189-000 |
| Деталь: | SCREW, M3X12 |
| Парткод: | QC2-1411-000 |
| Деталь: | BUSHING |
| Парткод: | QC2-1231-000 |
| Деталь: | SPRING, LEAF, GROUNDING |
| Парткод: | QC2-1236-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | QC2-1381-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | QC2-1234-000 |
| Деталь: | SENSOR UNIT, CAM, ROLL |
| Парткод: | QM3-0221-000 |
| Деталь: | GEAR, PENDULUM, TOP |
| Парткод: | QC2-1211-000 |
| Деталь: | GEAR, PENDULUM, BOTTOM |
| Парткод: | QC2-1244-000 |
| Деталь: | PENDULUM UNIT, LOWER, ROLL |
| Парткод: | QM3-0223-030 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | QC2-1210-000 |
| Деталь: | GEAR, PENDULUM, 1 |
| Парткод: | QC2-1212-020 |
| Деталь: | GEAR |
| Парткод: | QC2-1238-000 |
| Деталь: | GEAR |
| Парткод: | QC2-1214-000 |
| Деталь: | UPPER ROLL PENDULUM UNIT |
| Парткод: | QM3-0776-010 |
| Деталь: | GEAR |
| Парткод: | QC2-1213-000 |
| Деталь: | PENDULUM UNIT, 2, ROLL |
| Парткод: | QM3-0224-000 |
| Деталь: | GEAR, PENDULUM, 2 |
| Парткод: | QC2-1240-000 |
| Деталь: | HARNESS, WIRE, ROLL UNIT |
| Парткод: | QM3-0868-000 |
| Деталь: | HARNESS, WIRE, SENSOR, ROLL |
| Парткод: | QM3-0869-000 |
| Деталь: | WASHER |
| Парткод: | QC1-0710-000 |
| Деталь: | WASHER |
| Парткод: | QC1-4149-000 |
| Деталь: | ROLLER, GUIDE |
| Парткод: | QC2-1541-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | QC2-1191-000 |
| Деталь: | SCREW, TP, M3X10 |
| Парткод: | XA9-0831-000 |
| Деталь: | HOLDER, ROLL, LEFT, 2 |
| Парткод: | QM3-0717-000 |
| Деталь: | HOLDER, ROLL, LEFT, 1 |
| Парткод: | QM3-5311-000 |
| Деталь: | HOLDER, ROLL |
| Парткод: | QC2-6270-000 |
| Деталь: | TRAY, AUXILIARY |
| Парткод: | QC2-6262-000 |
| Деталь: | RING |
| Парткод: | QC2-4327-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | QC2-6569-000 |
| Деталь: | GEAR, 32T |
| Парткод: | QC2-6568-000 |
| Деталь: | ROLL UNIT |
| Парткод: | QM3-0711-000 |
| Деталь: | CUTTER UNIT |
| Парткод: | QM3-8146-010 |
| Деталь: | CUTTER UNIT |
| Парткод: | QM3-8149-010 |
| Деталь: | HARNESS, WIRE, COVER |
| Парткод: | QM3-0948-000 |
| Деталь: | HARNESS, WIRE, COVER |
| Парткод: | QM3-0923-000 |
| Деталь: | HARNESS, WIRE, COVER |
| Парткод: | QM3-6451-000 |
| Деталь: | HARNESS, WIRE, COVER |
| Парткод: | QM7-7087-000 |
| Деталь: | HARNESS, WIRE, COVER |
| Парткод: | QM7-7258-000 |
| Деталь: | CUTTER MOUNT UNIT |
| Парткод: | QM3-5310-010 |
| Деталь: | CUTTER MOUNT UNIT |
| Парткод: | QM3-0599-010 |
| Деталь: | CUTTER MOUNT UNIT |
| Парткод: | QM3-9931-000 |
| Деталь: | CUTTER MOUNT UNIT |
| Парткод: | QM4-8080-000 |
| Деталь: | CUTTER MOUNT UNIT |
| Парткод: | QM7-7261-000 |
| Деталь: | CUTTER DRIVE UNIT |
| Парткод: | QM3-0585-010 |
| Деталь: | BELT, TIMING |
| Парткод: | QC1-4850-000 |
| Деталь: | MOTOR, UNDER 10W, DC |
| Парткод: | QK1-0550-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5624-000 |
| Деталь: | MICRO SWITCH |
| Парткод: | WC4-5052-000 |
| Деталь: | LEVER, SENSOR |
| Парткод: | QC2-1274-000 |
| Деталь: | BELT, TIMING |
| Парткод: | QC2-0832-000 |
| Деталь: | JOINT, ROD |
| Парткод: | QC2-4346-000 |
| Деталь: | BAND, FIXING |
| Парткод: | QC2-4359-000 |
| Деталь: | SCREW, HEX SOCKET, M4X30 |
| Парткод: | QC2-5993-000 |
| Деталь: | BOX, ACCESSORY |
| Парткод: | QC2-5995-000 |
| Деталь: | BOLT |
| Парткод: | QC2-6006-000 |
| Деталь: | NUT |
| Парткод: | QC2-1330-000 |
| Деталь: | ROD, BASKET, FRONT |
| Парткод: | QC2-6009-000 |
| Деталь: | CAP, STAND |
| Парткод: | QC2-4348-000 |
| Деталь: | CASTER |
| Парткод: | QD1-0382-000 |
| Деталь: | CASTER, W/STOPPER |
| Парткод: | QD1-0383-000 |
| Деталь: | BASKET |
| Парткод: | QC2-6320-000 |
| Деталь: | ROD, BASKET, SUPPORT |
| Парткод: | QL2-2307-000 |
| Деталь: | ROD, BASKET, REAR |
| Парткод: | QL2-2308-000 |
| Деталь: | ARM, BASKET |
| Парткод: | QL2-2312-000 |
| Деталь: | HOLDER, ROD |
| Парткод: | QC2-6322-020 |
| Деталь: | SUPPORT, ROD |
| Парткод: | QC2-6323-010 |
| Деталь: | BASKET ROD UNIT |
| Парткод: | QM3-0728-000 |
| Деталь: | BASKET ROD UNIT |
| Парткод: | QM4-8086-000 |
| Деталь: | SUPPORT, BASKET |
| Парткод: | QC2-6005-000 |
| Деталь: | ROD, BASKET, REAR |
| Парткод: | QC2-6010-000 |
| Деталь: | BASKET |
| Парткод: | QD1-1146-000 |
| Деталь: | BASE, LABEL |
| Парткод: | QD1-0321-000 |
| Деталь: | LABEL, POSITIONING |
| Парткод: | QC2-6034-000 |
| Деталь: | PLATE, CASTER MOUNT |
| Парткод: | QC2-4349-000 |
| Деталь: | BASKET ROD |
| Парткод: | QC2-6327-000 |
| Деталь: | SUCTION FAN UNIT |
| Парткод: | QM3-0701-010 |
| Деталь: | FAN |
| Парткод: | QK1-2084-000 |
| Деталь: | AIR DUCT, 2 |
| Парткод: | QM3-0187-000 |
| Деталь: | SEAL, 4, AIR DUCT |
| Парткод: | QC2-1076-000 |
| Деталь: | SEAL, 3, AIR DUCT |
| Парткод: | QC2-1079-000 |
| Деталь: | AIR, DUCT |
| Парткод: | QC2-1071-000 |
| Деталь: | AIR DUCT, 3, REAR |
| Парткод: | QC2-1070-000 |
| Деталь: | AIR DUCT, 1 |
| Парткод: | QL2-1537-000 |
| Деталь: | HOLDER, TUBE GUIDE |
| Парткод: | QC2-6285-000 |
| Деталь: | FRONT DUCT UNIT |
| Парткод: | QM3-0698-010 |
| Деталь: | FRONT DUCT UNIT |
| Парткод: | QM3-0209-000 |
| Деталь: | M/C RELAY PCB ASSY |
| Парткод: | QM3-6661-000 |
| Деталь: | M/C RELAY PCB ASSY |
| Парткод: | QM3-0550-000 |
| Деталь: | TUBE GUIDE UNIT |
| Парткод: | QM3-0705-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-9918-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-6679-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8090-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8366-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8418-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-5295-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-0568-050 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-0775-000 |
| Деталь: | GUIDE, TUBE, CARRIAGE |
| Парткод: | QC2-0746-020 |
| Деталь: | IC, PHOTO INTERRUPTER, TLP1241 |
| Парткод: | WG8-5624-000 |
| Деталь: | BASE UNIT, JOINT |
| Парткод: | QM3-0584-000 |
| Деталь: | JOINT BASE UNIT |
| Парткод: | QM3-0699-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM3-5302-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM3-0162-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8096-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8097-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8414-000 |
| Деталь: | GEAR, VALVE 2 |
| Парткод: | QC2-0739-000 |
| Деталь: | GEAR, VALVE 3 |
| Парткод: | QC2-0740-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QC2-8591-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QC2-0742-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-1148-000 |
| Деталь: | BELT, TIMING |
| Парткод: | QC2-0832-000 |
| Деталь: | MOTOR, UNDER 10W, DC |
| Парткод: | QK1 -0550-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QC2-0763-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QD1-0257-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QD1-1151-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QC2-0764-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QD1-0256-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QD1-1150-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0368-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0862-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7084-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7231-000 |
| Деталь: | GUIDE, INK TUBE |
| Парткод: | QC2-1375-000 |
| Деталь: | GUIDE, INK TUBE |
| Парткод: | QD1-0307-000 |
| Деталь: | GUIDE, TUBE |
| Парткод: | QC2-6346-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-5294-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-0574-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-9919-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-6488-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM4-8020-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM4-8367-010 |
| Деталь: | HARNESS, WIRE, FEED |
| Парткод: | QM3-0928-000 |
| Деталь: | HARNESS, WIRE, FEED |
| Парткод: | QM7-7252-000 |
| Деталь: | JOINT, LEVER |
| Парткод: | QC2-0758-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0855-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0369-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7083-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7230-000 |
| Деталь: | HARNESS, WIRE, ROM, INK TANK |
| Парткод: | QM3-0903-000 |
| Деталь: | HARNESS, WIRE, ROM, INK TANK |
| Парткод: | QM3-0875-000 |
| Деталь: | HARNESS, WIRE, SENSOR, VALVE |
| Парткод: | QM3-0914-000 |
| Деталь: | HARNESS, WIRE, SENSOR, VALVE |
| Парткод: | QM3-0886-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM3-0901-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM3-0872-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM7-7082-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM7-7256-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0947-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0882-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0924-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM7-7080-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM7-7253-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM3-0884-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM3-0925-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM7-7081-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM7-7254-000 |
| Деталь: | INK TUBE UNIT (L) |
| Парткод: | QM3-5296-000 |
| Деталь: | INK TUBE UNIT (L) |
| Парткод: | QM3-9920-000 |
| Деталь: | INK TUBE UNIT (R) |
| Парткод: | QM3-5297-000 |
| Деталь: | INK TUBE UNIT (R) |
| Парткод: | QM3-9921-000 |
| Деталь: | WASHER |
| Парткод: | QC1-4149-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-0269-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-1060-000 |
| Деталь: | GEAR, VALVE |
| Парткод: | QD1-0270-000 |
| Деталь: | LEVER, TENSION |
| Парткод: | QD1-0271-000 |
| Деталь: | ROLLER, TENSION |
| Парткод: | QD1-0272-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QD1-0273-000 |
| Деталь: | SHAFT |
| Парткод: | QD1-0274-000 |
| Деталь: | PULLEY, BELT |
| Парткод: | QD1-0298-000 |
| Деталь: | PHOTO-INTERRUPTER, SG2481 |
| Парткод: | WG8-5776-000 |
| Деталь: | HARNESS, VALVE UNIT |
| Парткод: | QM7-7232-000 |
| Деталь: | HARNESS, VALVE, RELAY |
| Парткод: | QM7-7233-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | JOINT, ROD |
| Парткод: | QC2-4346-000 |
| Деталь: | BAND, FIXING |
| Парткод: | QC2-4359-000 |
| Деталь: | SCREW, HEX SOCKET, M4X30 |
| Парткод: | QC2-5993-000 |
| Деталь: | BOX, ACCESSORY |
| Парткод: | QC2-5995-000 |
| Деталь: | BOLT |
| Парткод: | QC2-6006-000 |
| Деталь: | NUT |
| Парткод: | QC2-1330-000 |
| Деталь: | ROD, BASKET, FRONT |
| Парткод: | QC2-6009-000 |
| Деталь: | CAP, STAND |
| Парткод: | QC2-4348-000 |
| Деталь: | CASTER |
| Парткод: | QD1-0382-000 |
| Деталь: | CASTER, W/STOPPER |
| Парткод: | QD1-0383-000 |
| Деталь: | BASKET |
| Парткод: | QC2-6320-000 |
| Деталь: | ROD, BASKET, SUPPORT |
| Парткод: | QL2-2307-000 |
| Деталь: | ROD, BASKET, REAR |
| Парткод: | QL2-2308-000 |
| Деталь: | ARM, BASKET |
| Парткод: | QL2-2312-000 |
| Деталь: | HOLDER, ROD |
| Парткод: | QC2-6322-020 |
| Деталь: | SUPPORT, ROD |
| Парткод: | QC2-6323-010 |
| Деталь: | BASKET ROD UNIT |
| Парткод: | QM3-0728-000 |
| Деталь: | BASKET ROD UNIT |
| Парткод: | QM4-8086-000 |
| Деталь: | SUPPORT, BASKET |
| Парткод: | QC2-6005-000 |
| Деталь: | ROD, BASKET, REAR |
| Парткод: | QC2-6010-000 |
| Деталь: | BASKET |
| Парткод: | QD1-1146-000 |
| Деталь: | BASE, LABEL |
| Парткод: | QD1-0321-000 |
| Деталь: | LABEL, POSITIONING |
| Парткод: | QC2-6034-000 |
| Деталь: | PLATE, CASTER MOUNT |
| Парткод: | QC2-4349-000 |
| Деталь: | BASKET ROD |
| Парткод: | QC2-6327-000 |
| Деталь: | LUBE, FLOIL G-5000H, GREASE |
| Парткод: | FY9-6022-000 |
| Деталь: | GREASE, EU-1 |
| Парткод: | FY9-6028-000 |
| Деталь: | ADJUSTING UNIT, CR WIRE |
| Парткод: | AY3-4493-000 |
| Деталь: | TUBE, WASTE INK |
| Парткод: | AY3-4595-000 |
| Деталь: | W-INK TUBE, BLACK |
| Парткод: | AY3-4530-000 |
| Деталь: | SYRINGE |
| Парткод: | CK-0541-000 |
| Деталь: | STOPPER |
| Парткод: | QC2-6710-000 |
| Деталь: | PINCH ROLLER UNIT 1 |
| Парткод: | QM3-0760-000 |
| Деталь: | PINCH ROLLER UNIT 1 |
| Парткод: | QM3-5308-000 |
| Деталь: | ROLLER, PINCH |
| Парткод: | QL2-2317-000 |
| Деталь: | ROLLER, PINCH |
| Парткод: | QL2-2418-000 |
| Деталь: | RING |
| Парткод: | QC2-0682-000 |
| Деталь: | LEVER, A |
| Парткод: | QC2-0982-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | QC2-0994-000 |
| Деталь: | LEVER, B |
| Парткод: | QC2-0996-000 |
| Деталь: | PINCH ROLLER UNIT 2 |
| Парткод: | QM3-0761-000 |
| Деталь: | PINCH ROLLER UNIT 2 |
| Парткод: | QM3-5309-000 |
| Деталь: | GUIDE UNIT, PAPER |
| Парткод: | QM3-0566-020 |
| Деталь: | ROLLER, GUIDE, INNER |
| Парткод: | QC2-1317-000 |
| Деталь: | GUIDE ROLLER UNIT |
| Парткод: | QM3-0767-000 |
| Деталь: | GUIDE UNIT, INNER, STRAIGHT PA |
| Парткод: | QM3-0579-020 |
| Деталь: | ROLLER |
| Парткод: | QC1-2950-000 |
| Деталь: | GUIDE, OUTER |
| Парткод: | QM3-0580-030 |
| Деталь: | SPRING, TORSION |
| Парткод: | QC2-0933-010 |
| Деталь: | FLAPPER |
| Парткод: | QD1-0966-000 |
| Деталь: | GUIDE, WASTE INK |
| Парткод: | QC2-1460-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | QC2-0981-000 |
| Деталь: | ROLLER, GUIDE |
| Парткод: | QC2-1541-000 |
| Деталь: | GUIDE, INNER |
| Парткод: | QC2-0935-020 |
| Деталь: | SPRING, TENSION |
| Парткод: | QC2-0997-000 |
| Деталь: | MOTOR, 26.4V, DC |
| Парткод: | QK1 -0447-000 |
| Деталь: | MOTOR, DC BRUSHLESS |
| Парткод: | QK1-2083-000 |
| Деталь: | SENSOR UNIT, LINE FEED |
| Парткод: | QM2-3420-000 |
| Деталь: | BELT, DRIVE, PAPER TRANSPORT |
| Парткод: | QC2-0957-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QC2-1396-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QC2-0985-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QC2-0990-000 |
| Деталь: | WHEEL, CODE |
| Парткод: | QC3-1885-000 |
| Деталь: | COVER, CODE WHEEL |
| Парткод: | QC2-0995-000 |
| Деталь: | SENSOR UNIT, HOME POSITION, LI |
| Парткод: | QM2-3423-000 |
| Деталь: | FLANGE, PULLEY |
| Парткод: | QC2-0998-000 |
| Деталь: | MOTOR, STEPPING DC 10W UNDER |
| Парткод: | QK1 -0440-000 |
| Деталь: | SCALE, LINEAR |
| Парткод: | QC3-1882-010 |
| Деталь: | SCALE, LINEAR |
| Парткод: | QC3-1888-010 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5624-000 |
| Деталь: | IDLER PULLEY UNIT |
| Парткод: | QM3-0161-000 |
| Деталь: | GEAR, LIFT |
| Парткод: | QC2-0678-000 |
| Деталь: | CAM, LIFTER |
| Парткод: | QC3-2664-000 |
| Деталь: | CAM, LIFTER |
| Парткод: | QC2-0675-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | QC2-0676-000 |
| Деталь: | RING |
| Парткод: | QC2-0681-000 |
| Деталь: | RING |
| Парткод: | QC2-0682-000 |
| Деталь: | BUSHING, POLYPLASTICS |
| Парткод: | QC2-0683-000 |
| Деталь: | GEAR, RELEASE, IDLER |
| Парткод: | QC2-0685-000 |
| Деталь: | GEAR, LIFT, IDLER A |
| Парткод: | QC2-0686-000 |
| Деталь: | GEAR, LIFT, IDLER B |
| Парткод: | QC2-0687-000 |
| Деталь: | GEAR, LIFT, DOUBLE A |
| Парткод: | QC2-0688-000 |
| Деталь: | GEAR, LIFT, DOUBLE B |
| Парткод: | QC2-0689-000 |
| Деталь: | GEAR, LIFT, DOUBLE C |
| Парткод: | QC2-0690-000 |
| Деталь: | GEAR, RELEASE, PRESSURE |
| Парткод: | QC2-0684-000 |
| Деталь: | TUBE LEVER GUIDE UNIT |
| Парткод: | QM3-6665-000 |
| Деталь: | SENSOR UNIT, HUMIDITY |
| Парткод: | WP2-5187-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM3-4347-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM3-4342-010 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM3-0576-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM3-4346-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM3-6657-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM3-9928-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM4-8079-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM7-7111-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM7-7222-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM7-7223-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM7-7245-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | QM7-7246-000 |
| Деталь: | BATTERY, LITHIUM |
| Парткод: | WK1-5207-000 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | QK1 -2073-010 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | QK1 -2813-000 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | QK1 -2745-010 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | QK1 -2746-000 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | QK1 -5942-000 |
| Деталь: | HDD EXPANSION BOARD ASSY |
| Парткод: | QM3-4348-000 |
| Деталь: | HDD EXPANSION BOARD ASSY |
| Парткод: | QM4-8071-000 |
| Деталь: | HDD UNIT, WD800BEVT-22ZCT0 |
| Парткод: | QM3-4344-010 |
| Деталь: | HARNESS, WIRE, HDD |
| Парткод: | QM2-3432-000 |
| Деталь: | HARNESS, WIRE, POWER |
| Парткод: | QM3-0853-000 |
| Деталь: | HARNESS, WIRE, POWER |
| Парткод: | QM3-0927-000 |
| Деталь: | HARNESS, WIRE, POWER |
| Парткод: | QM3-6421-000 |
| Деталь: | HARNESS, WIRE, HIGROMETER |
| Парткод: | QM3-0858-000 |
| Деталь: | HARNESS, WIRE, HIGROMETER |
| Парткод: | QM7-7086-000 |
| Деталь: | HARNESS, WIRE, HIGROMETER |
| Парткод: | QM7-7255-000 |
| Деталь: | HOLDER, CORE, CABLE |
| Парткод: | QC2-0606-000 |
| Деталь: | HARNESS, WIRE, INLET |
| Парткод: | QM3-0863-000 |
| Деталь: | HARNESS, WIRE, 2, CROSSING |
| Парткод: | QM3-0936-000 |
| Деталь: | HARNESS, WIRE, 1, CROSSING |
| Парткод: | QM3-0937-000 |
| Деталь: | HARNESS, WIRE, BASE UNIT |
| Парткод: | QM3-0895-000 |
| Деталь: | HARNESS, WIRE, BASE UNIT |
| Парткод: | QM3-0920-000 |
| Деталь: | HARNESS, WIRE, BASE UNIT |
| Парткод: | QM3-6423-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | QC2-0612-000 |
| Деталь: | GUIDE, HDD CABLE |
| Парткод: | QC2-8596-000 |
| Деталь: | CONNECTOR UNIT |
| Парткод: | QM3-0527-000 |
| Деталь: | CABLE, FLAT, CONTROL PANEL |
| Парткод: | QK1-9686-000 |
| Деталь: | CABLE, FLEXIBLE |
| Парткод: | QK1-2756-000 |
| Деталь: | RETAINING PLATE, HARNESS, WIRE |
| Парткод: | QC2-1373-000 |
| Деталь: | CLAMP, CORD |
| Парткод: | WT2-0136-000 |
| Деталь: | CLIP, CABLE |
| Парткод: | WT2-0317-000 |
| Деталь: | SADDLE, WIRE |
| Парткод: | WT2-5701-000 |
| Деталь: | SADDLE, WIRE |
| Парткод: | WT2-0494-000 |
| Деталь: | SADDLE, WIRE |
| Парткод: | WT2-5018-000 |
| Деталь: | SADDLE, WIRE |
| Парткод: | WT2-5056-000 |
| Деталь: | SADDLE, WIRE |
| Парткод: | WT2-5064-000 |
| Деталь: | SADDLE, WIRE |
| Парткод: | WT2-5694-000 |
| Деталь: | SADDLE, WIRE |
| Парткод: | WT2-5760-000 |
| Деталь: | SCREW, ALLEN, M3X8 |
| Парткод: | XA9-1658-000 |
| Деталь: | HARNESS, WIRE |
| Парткод: | QM3-6426-000 |
| Деталь: | HARNESS, WIRE |
| Парткод: | QM3-0870-000 |
| Деталь: | HARNESS, WIRE |
| Парткод: | QM7-7085-000 |
| Деталь: | HDD, WD800BEVT-22ZCT 0 |
| Парткод: | FK2-2416-000 |
| Деталь: | HDD, MK1676GSX(HDD2J96QSL) |
| Парткод: | WM2-5278-000 |
| Деталь: | HDD, HTS545025A7E330, HGST |
| Парткод: | WM2-5288-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-5295-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-0568-050 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-0775-000 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-9918-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM3-6679-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8090-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8366-010 |
| Деталь: | INK SUPPLY UNIT |
| Парткод: | QM4-8418-000 |
| Деталь: | GUIDE, TUBE, CARRIAGE |
| Парткод: | QC2-0746-020 |
| Деталь: | IC, PHOTO INTERRUPTER, TLP1241 |
| Парткод: | WG8-5624-000 |
| Деталь: | BASE UNIT, JOINT |
| Парткод: | QM3-0584-000 |
| Деталь: | JOINT BASE UNIT |
| Парткод: | QM3-0699-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM3-5302-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM3-0162-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8096-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8097-000 |
| Деталь: | INK SUPPLY DRIVE UNIT |
| Парткод: | QM4-8414-000 |
| Деталь: | GEAR, VALVE 2 |
| Парткод: | QC2-0739-000 |
| Деталь: | GEAR, VALVE 3 |
| Парткод: | QC2-0740-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QC2-8591-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QC2-0742-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-1148-000 |
| Деталь: | BELT, TIMING |
| Парткод: | QC2-0832-000 |
| Деталь: | MOTOR, UNDER 10W, DC |
| Парткод: | QK1 -0550-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QC2-0763-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QD1-0257-000 |
| Деталь: | ABSORBER, INK, UPPER |
| Парткод: | QD1-1151-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QC2-0764-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QD1-0256-000 |
| Деталь: | ABSORBER, INK, LOWER |
| Парткод: | QD1-1150-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0368-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0862-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7084-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7231-000 |
| Деталь: | GUIDE, INK TUBE |
| Парткод: | QC2-1375-000 |
| Деталь: | GUIDE, INK TUBE |
| Парткод: | QD1-0307-000 |
| Деталь: | GUIDE, TUBE |
| Парткод: | QC2-6346-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-5294-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-0574-000 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-9919-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM3-6488-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM4-8020-010 |
| Деталь: | INK SUPPLY UNIT (R) |
| Парткод: | QM4-8367-010 |
| Деталь: | HARNESS, WIRE, FEED |
| Парткод: | QM3-0928-000 |
| Деталь: | HARNESS, WIRE, FEED |
| Парткод: | QM7-7252-000 |
| Деталь: | JOINT, LEVER |
| Парткод: | QC2-0758-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0855-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM3-0369-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7083-000 |
| Деталь: | HARNESS, WIRE, INK SENSOR |
| Парткод: | QM7-7230-000 |
| Деталь: | HARNESS, WIRE, ROM, INK TANK |
| Парткод: | QM3-0903-000 |
| Деталь: | HARNESS, WIRE, ROM, INK TANK |
| Парткод: | QM3-0875-000 |
| Деталь: | HARNESS, WIRE, SENSOR, VALVE |
| Парткод: | QM3-0914-000 |
| Деталь: | HARNESS, WIRE, SENSOR, VALVE |
| Парткод: | QM3-0886-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM3-0901-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM3-0872-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM7-7082-000 |
| Деталь: | HARNESS, WIRE, VALVE MOTOR |
| Парткод: | QM7-7256-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0947-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0882-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM3-0924-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM7-7080-000 |
| Деталь: | HARNESS, WIRE, INK TANK |
| Парткод: | QM7-7253-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM3-0884-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM3-0925-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM7-7081-000 |
| Деталь: | HARNESS, WIRE, 2, INK TANK |
| Парткод: | QM7-7254-000 |
| Деталь: | INK TUBE UNIT (L) |
| Парткод: | QM3-5296-000 |
| Деталь: | INK TUBE UNIT (L) |
| Парткод: | QM3-9920-000 |
| Деталь: | INK TUBE UNIT (R) |
| Парткод: | QM3-5297-000 |
| Деталь: | INK TUBE UNIT (R) |
| Парткод: | QM3-9921-000 |
| Деталь: | WASHER |
| Парткод: | QC1-4149-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-0269-000 |
| Деталь: | CAM, VALVE |
| Парткод: | QD1-1060-000 |
| Деталь: | GEAR, VALVE |
| Парткод: | QD1-0270-000 |
| Деталь: | LEVER, TENSION |
| Парткод: | QD1-0271-000 |
| Деталь: | ROLLER, TENSION |
| Парткод: | QD1-0272-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QD1-0273-000 |
| Деталь: | SHAFT |
| Парткод: | QD1-0274-000 |
| Деталь: | PULLEY, BELT |
| Парткод: | QD1-0298-000 |
| Деталь: | PHOTO-INTERRUPTER, SG2481 |
| Парткод: | WG8-5776-000 |
| Деталь: | HARNESS, VALVE UNIT |
| Парткод: | QM7-7232-000 |
| Деталь: | HARNESS, VALVE, RELAY |
| Парткод: | QM7-7233-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | PLATE, BACK |
| Парткод: | QD1-0026-000 |
| Деталь: | LEVER, SENSOR, TOP COVER |
| Парткод: | QD1-0039-000 |
| Деталь: | COVER, RIGHT |
| Парткод: | QD1-0049-000 |
| Деталь: | COVER, TOP, LEFT |
| Парткод: | QD1-0050-000 |
| Деталь: | COVER, TOP, RIGHT |
| Парткод: | QD1-0051-000 |
| Деталь: | COVER, BOTTOM, RIGHT |
| Парткод: | QD1-0052-000 |
| Деталь: | COVER, BOTTOM, LEFT |
| Парткод: | QD1-0054-000 |
| Деталь: | COVER, TOP, LEFT |
| Парткод: | QD1-0056-000 |
| Деталь: | COVER, FRONT, LEFT |
| Парткод: | QD1-0057-000 |
| Деталь: | COVER, LEFT |
| Парткод: | QD1-0058-000 |
| Деталь: | LEVER, SENSOR |
| Парткод: | QD1-0098-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | QD1-0099-000 |
| Деталь: | SHEET, EJECT GUIDE |
| Парткод: | QD1-0485-000 |
| Деталь: | UPPER COVER UNIT |
| Парткод: | QM4-8054-000 |
| Деталь: | PAPER DELIVERY GUIDE UNIT |
| Парткод: | QM4-8058-000 |
| Деталь: | HARNESS, WIRE, PRINTER IF |
| Парткод: | QM7-7093-000 |
| Деталь: | SCREW, TP, M3X8 |
| Парткод: | XA9-1928-000 |
| Деталь: | COVER, MAIN, FRONT |
| Парткод: | QD1-0042-000 |
| Деталь: | COVER, CM SENSOR |
| Парткод: | QD1-0063-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | QD1-0064-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | QD1-0065-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | QD1-0071-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | QD1-0072-000 |
| Деталь: | BELT |
| Парткод: | QD1-0073-000 |
| Деталь: | GEAR, 20T/48T |
| Парткод: | QD1-0087-000 |
| Деталь: | SHEET, CABLE GUIDE |
| Парткод: | QD1-0090-000 |
| Деталь: | LEVER, SENSOR |
| Парткод: | QD1-0097-000 |
| Деталь: | DUCT |
| Парткод: | QD1-0101-000 |
| Деталь: | LOUVER |
| Парткод: | QD1-0102-000 |
| Деталь: | PAD |
| Парткод: | QD1-0108-000 |
| Деталь: | PAD, 2 |
| Парткод: | QD1-0109-000 |
| Деталь: | PAD, 3 |
| Парткод: | QD1-0111-000 |
| Деталь: | FLAPPER, GUIDE |
| Парткод: | QD1-0140-000 |
| Деталь: | HOLDER, GUIDE |
| Парткод: | QD1-0141-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | QD1-0142-000 |
| Деталь: | SHAFT, GUIDE |
| Парткод: | QD1-0143-000 |
| Деталь: | SCREW, STEPPED, M3 |
| Парткод: | QD1-0475-000 |
| Деталь: | CM SENSOR UNIT |
| Парткод: | QK1-9590-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | QK1-9594-000 |
| Деталь: | COVER, FRAME |
| Парткод: | QL2-8062-000 |
| Деталь: | BELT TENSIONER UNIT |
| Парткод: | QM4-8026-000 |
| Деталь: | PLATE, PAPER PRESS |
| Парткод: | QM4-8031-000 |
| Деталь: | WHITE TILE HOLDER UNIT |
| Парткод: | QM4-8032-000 |
| Деталь: | CARRIAGE UNIT |
| Парткод: | QM4-8033-000 |
| Деталь: | CABLE UNIT |
| Парткод: | QM4-8040-000 |
| Деталь: | FAN UNIT |
| Парткод: | QM4-8042-000 |
| Деталь: | COVER DETECT UNIT |
| Парткод: | QM4-8043-000 |
| Деталь: | HARNESS, WIRE, FAN |
| Парткод: | QM7-7089-000 |
| Деталь: | HARNESS, WIRE, FAN, RELAY |
| Парткод: | QM7-7090-000 |
| Деталь: | PHOTO-INTERRUPTER, SG2481 |
| Парткод: | WG8-5776-000 |
| Деталь: | SCREW, M3X6 |
| Парткод: | XA9-0894-010 |
| Деталь: | SCREW, STEPPED M3 |
| Парткод: | XA9-1340-000 |
| Деталь: | SCREW, TP, M3X8 |
| Парткод: | XA9-1928-000 |
| Деталь: | BEARING, BALL |
| Парткод: | XG9-0473-000 |
Коды ошибок
01xxxxxx-xxx
03xxxxxx-xxx
1000 ... 100C
100F
1010
1012
1013
1015
1021
1022
1030
1031
1032
1034
1035
1036
1037
1038
1039
103A
1040
1041
1043
1047
1048
1049
1050
1051
1052
1053
1054
1056 ... 1062
1100
1101
1400 ... 140C
1410 ... 141C
200A
200B
200C
200E
200F
2010
2015
2016
2017
2018
2019
201A
201B
201C
201D
201E
2405
2406
2407
2408
2409
240A
2500 ... 250C
2510 ... 251C
2520 ... 252C
2540 ... 254C
2560 ... 256C
2570 ... 257C
2580 ... 258C
2590 ... 259C
259C ... 25A8
25B7
260E
260F
2800
2801
2802
2803
2804
2805
2807
2808
2809
280A
280B
280C, 280D, 280E
2811
2812
2813
2816
2817
2818
2819
281A
281B
2820
2821
2822
2823
2824
2825
2826
2827, 2828, 2829
282A
282B
282D
282E
2830
2832
2833
2834
2835
2836
2901
2902
2905
2906
2907
2908
2909
290A
2918
291A
291B
291D
2920
2921
2930
2931
2E00
2E01
2E02
2E03
2E04
2E05
2E08
2E09
2E0A
2E0B
2E0C
2E0E
2E0F
2E10
2E11
2E12
2E14
2E15
2E16
2E17
2E18
2E19
2E1A
2E1B
2E1C
2E1D
2E1F
2E20
2E21
2E22
2E23
2E24
2E25
2E27
2E30
2E31
2E32
2E33
2E34
2E35
2E36
2E37
2E38
2E39
2E3A
2E3B
2E3C
2E3D
2E3E
2E3F
2E40
2E41
2E42
2E45
2E47
2F11
2F12
2F13
2F14
2F16
2F17
2F1F
2F20
2F21
2F22
2F23
2F24
2F25
2F26
2F27
2F28
2F29
2F2A
2F2B
2F2C
2F2D
2F2E
2F2F
2F30
2F32
2F33
2F34
2F35
2F37
2F38
2F3A
2F3B
2F3C
2F3D
2F3E
2F3F
2F40
2F41
2F42
2F43
2F44
2F46
2F47
2F48
2F49, 2F50, 2F51
2F4A
2F4D
2F4F
2F52
2F53
2F54
2F60
2F61
2F62
2F63
2F65
2F66
2F67
2F68
2F69
2F6A
2F6B
2F6C
2F70
2F71
2F72
2F80
2F81
2F82
2F83
2F85
2F86
2F87
2F88
2F89
2F90
2FA0
4001
401A
401B
401C
401D
401E
4027
4034
4037
403E
403F
4040
4041
4042
4043
4044
4045
4046
4047
4048
4049
404A
404B
404C
404D
404E
404F
4050
405A
405B
4061
xx01xxxx-xxxx
xx03xxxx-xxxx
xx06xxxx-xxxx
xx13xxxx-xxxx
xx1Axxxx-xxxx
xx32xxxx-xxxx
xx34xxxx-xxxx
xx80xxxx-xxxx
xx81xxxx-xxxx
xx83xxxx-xxxx
xx84xxxx-xxxx
xx86xxxx-xxxx
xx87xxxx-xxxx
xx89xxxx-xxxx
xx90xxxx-xxxx
Описание
| Error code: | 01xxxxxx-xxx |
| Description: | Warning |
| Error code: | 03xxxxxx-xxx |
| Description: | Error |
| Error code: | 1000 ... 100C |
| Display: | Ink Level: Check Not much ink is left. Prepare to replace the ink. |
| Description: | Ink tank near-empty (continued use allowed) The remaining volume of ink is diminishing (below the pin check level). (XX: Target color display) Last 2 digits of error code: 00:Bk, 01:Y, 02:M, 03:C, 04:PM, 05:PC, 06:MBk1, 07:MBk2, 08:GY, 09:PGY, 0A:R, 0B:B, 0C:G |
| Remedy: | 1. Replace the tank (continued usage allowed). 2. If the problem persists after the tank has been replaced, the remaining ink detection system is at fault. (Replace the supply unit or check catching wire or connection status of harness.) |
| Error code: | 100F |
| Display: | End of paper feed. Cannot feed paper any more. |
| Description: | The limit of forced paper feeding. The media reached to a pinchroller at feeding backfeed media manually. (not an error or a failure) |
| Remedy: | The message is cleared automatically after displaying for 2sec. Confirmation of Paper detection sensor/ Media sensor sensor (I/O mode) |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1012 |
| Display: | Problem with Printhead R Chk printing results |
| Description: | Printhead R non-ejection warning (doublehead model) (Check printout/ possible to continue printing) See 280C for detection criteria. |
| Causes: | The number of non-ejection nozzles is zero to 100 after recovery cleaning of non-ejection detection. In addition, the number of non-ejection complementary disabled nozzles is 30 or more. |
| Remedy: | 1. Check image quality. (Unless there are problems with the image quality, there is no need to replace the printhead.) 2. Replace the printhead. |
| Error code: | 1013 |
| Display: | Problem with Printhead L Chk printing results |
| Description: | Printhead L non-ejection warning (doublehead model) (Check printout/ possible to continue printing) See 280C for detection criteria. |
| Remedy: | 1. Check image quality. (Unless there are problems with the image quality, there is no need to replace the printhead.) 2. Replace the printhead. |
| Error code: | 1015 |
| Display: | This type of paper is not compatible with HP-GL/2. |
| Description: | Internal Stationary Jam 2 |
| Causes: | Top Sensor/Media Width Sensor /Fixing Delivery Sensor/ Duplex Feede Sensor/PF Feed Sensor PS215/PS225/ PS2,PS3/PS502/ PS8008 |
| Error code: | 1021 |
| Display: | Papr Type Mismatch |
| Description: | RAM Error (Slot 1) |
| Error code: | 1022 |
| Display: | Papr Type Mismatch |
| Description: | Paper mismatch (type) With [Warning Indication] is selected for [Paper Mismatch Detection], the type of loaded paper mismatches the specified type. Or, with [Pause] is selected for [Paper Mismatch Detection], the [Online] button was pressed to execute forced printing. |
| Remedy: | Continued printing is allowed. Check driver setting. Replace with appropriate paper. |
| Error code: | 1030 |
| Display: | GARO W1221 |
| Description: | PF lift motor 1 error (paper feeder) After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 1. Replace the PF lift motor 1. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1031 |
| Display: | GARO W1222 |
| Description: | (Image mode) Invalid parameter count (no parameters) A numeric field has not been identified as being numeric during Image mode command decoding. |
| Remedy: | 1. Identify the model. 2. If the error has occurred with RIP, try with the printer driver. 3. Try in an alternative environment (I/ F, PC). |
| Error code: | 1032 |
| Display: | GARO W1223 |
| Description: | (Image mode) Required item missing A character out of bounds has been detected where a group or end parameter character ought to exist, during Image mode command decoding. |
| Remedy: | 1. Identify the model. 2. If the error has occurred with RIP, try with the printer driver. 3. Try in an alternative environment (I/ F, PC). |
| Error code: | 1034 |
| Display: | GARO W1225 |
| Description: | (Image mode)Other warning A character other than <ESC> has been detected right after the image mode analysis module entered Image mode or when the decoding of a single command ended. |
| Remedy: | 1. Identify the model. 2. If the error has occurred with RIP, try with the printer driver. 3. Try in an alternative environment (I/ F, PC). |
| Error code: | 1035 |
| Display: | GARO W1231 |
| Description: | (Setup mode)Unknown command A command character string other than RESET, SET, OPCMT0 and OPCMT2 has been detected in a PJL command. |
| Remedy: | 1. Identify the model. 2. If the error has occurred with RIP, try with the printer driver. 3. Try in an alternative environment (I/ F, PC). |
| Error code: | 1036 |
| Display: | GARO W1232 |
| Description: | Power-on jam (PI5) (Related to Finisher) |
| Error code: | 1037 |
| Display: | GARO W1233 |
| Description: | (Setup mode) Required item missing The exit parameter is missing in the EnterGAROMode command and the UniversalExitLanguage command used in Setup mode. |
| Remedy: | 1. Identify the model. 2. If the error has occurred with RIP, try with the printer driver. 3. Try in an alternative environment (I/ F, PC). |
| Error code: | 1038 |
| Display: | Interface failure CODE (1038) Turn power off, on |
| Description: | Interface Failure. • Engine Control Board to Image Processor Board connection failure. • The copier determines that there is an error if the Engine Control Board fails to send an acknowledgement signal to the Image Processor Board for a given period of time or more. • An error command signal is transmitted from the Image Processor Board to Engine Control Board. • An error status signal is transmitted from the Engine Control Board to Image Processor Board. |
| Causes: | • Engine Control Board, PL13.0.20 • Image Processor Board, PL2.0.4 |
| Remedy: | 1 Check every connector on the Engine Control Board and the Image Processor Board. Are the connectors seated properly? Go to step 2. Reseat the connectors. If the problem persists, go to step 2. 2 Replace the Image Processor Board. Does the problem persist? Go to step 3. Complete. 3 Change the Engine Control Board. Complete. |
| Error code: | 1039 |
| Display: | GARO W1235 |
| Description: | (Setup mode) Other warning A character string other than the @PJL prefix has been detected while the analysis module was idle. |
| Remedy: | 1. Identify the model. 2. If the error has occurred with RIP, try with the printer driver. 3. Try in an alternative environment (I/ F, PC). |
| Error code: | 103A |
| Display: | GARO W1226 |
| Description: | (Image mode) Image processing table error No image processing table is being transmitted, a required image processing table is unavailable, or an image processing table contains a value out of bounds. |
| Remedy: | 1. Retransmit. 2. Check with a different interface choice. 3. Try by printing other data. 4. With RIP, print from the print driver. Supplement: If this error occurs, the print result would appear blank. |
| Error code: | 1040 |
| Display: | GL2: W0501 The memory is full. |
| Description: | PF lift motor 2 error (paper feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 2. Replace the PF lift motor 2. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1041 |
| Display: | GL2: W0502 The parameter is out of range. |
| Description: | HP/GL2 error; invalid parameter Data having an invalid number of types of parameters that follow the command has been detected. |
| Remedy: | Verify the data and fix it. |
| Error code: | 1043 |
| Display: | GL2: W0504 This command is not supported. |
| Description: | HP/GL2 error; Invalid command A command that is not defined in HP-GL/2 or HP RTL is included. |
| Remedy: | Verify the data and fix it. |
| Error code: | 1047 |
| Display: | GL2: W0903 The memory is full. |
| Description: | HP/GL2 error; replot buffer overflow Data storage buffers have run short. |
| Remedy: | 1. Reduce the size of rendering data. 2. Replace with HP RTL data for manipulation with On The Fly*. *: On The Fly: The method to transmit data in sequence from paper. The software that generates HP-GL/2 data has this option to specify. Select this option to save the memory usage of the printer. |
| Error code: | 1048 |
| Display: | GL2: W0904 The memory is full. |
| Description: | HP/GL2 error; polygon buffer overflow The size of drawing data exceeds the processing capacity. |
| Remedy: | 1. Reduce the size of rendering data. 2. Replace with HP RTL data for manipulation with On The Fly*. *: On The Fly: The method to transmit data in sequence from paper. The software that generates HP-GL/2 data has this option to specify. Select this option to save the memory usage of the printer. |
| Error code: | 1049 |
| Display: | Before borderless printing, move the blue platen switch. |
| Description: | When print data with borderless printing specification has been received, platen shutter was closed. |
| Remedy: | Open the platen shutter. |
| Error code: | 1050 |
| Display: | Blue platen switch is dirty. Please clean the switch. |
| Description: | SM lift motor error (side multi tray) After cassette 5 is inserted, SM lift sensor does not turn on within 12 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor Defective SM lift motor. Defective SM main PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. SM Lift motor 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM Lift motor and SM main PWB (YC5) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the SM Lift motor. SM Lift sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM Lift sensor and SM main PWB (YC7) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the SM Lift sensor. SM main PWB Replace the SM main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1051 |
| Display: | Paper Too Small |
| Description: | Paper mismatch (size) Size clip warning With [Warning Indication] selected for [Paper Mismatch Detection] in the menu settings, the size of paper loaded is smaller than that of specified from driver. |
| Causes: | Loading of smaller media into the printer than the media selected in the printer driver. |
| Remedy: | Continued printing allowed. Check driver settings. Replace with appropriate paper. |
| Error code: | 1052 |
| Display: | Borderless printng not possible. Check supported paper. |
| Description: | Borderless printing not available (unsupported size) With [Warning Indication] selected for [Paper Mismatch Detection] in the menu settings, borderless printing data is received, but roll paper not supporting borderless printing has been loaded. |
| Causes: | When the following conditions are satisfied. • [Detect paper setting mismatch] is set at other than “Pause”. • Loading of borderless printing unsupported media in borderless printing. |
| Remedy: | Replace with appropriate paper. |
| Error code: | 1053 |
| Display: | Paper position not suitable for borderless printing. |
| Description: | Borderless printing not available (physical) With [Warning Indication] selected for [Paper Mismatch Detection] in the menu settings, borderless printing data is received, but roll paper loaded is more than 1mm off the predefined position for the pre-ejection opening at the counter-HP side. |
| Causes: | When the following conditions are satisfied. • [Detect paper setting mismatch] is set at other than “Pause”. • The multi sensor detects that the paper edge at the home position side is not positioned within +/-3mm from the reference paper position when borderless printing is started. |
| Remedy: | Reload/ replace the roll paper. |
| Error code: | 1054 |
| Display: | PaprWidth Mismatch |
| Description: | Top Sensor/Media full sensor/Fixing Delivery Sensor PS204/205/915 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor |
| Error code: | 1056 ... 1062 |
| Display: | Move the blue platen switch No.XX to the right. |
| Description: | The multisensor detected that the platen shutter used for pre-ejection was closed. Detection timing: -At paper loading -At start of first printing (after upper cover is opened and closed, or recovery from sleep mode, or the power is turned on with paper loaded) The following list shows the last 2 digits of error codes and the corresponding messages. 56:No.2, 57:No.3, 58:No.459:No.5, 5A:No.6, 5B:No.75C:No.8, 5D:No.9, 5E:No.105F:No.11, 60:No.12, 61:No.13, 62:No.14 |
| Remedy: | Move the platen shutter relevant to the message to the right, to open it. |
| Error code: | 1100 |
| Display: | Prepare for maint cart replacement. |
| Description: | Paper Jam There is paper jammed in the All-In-One. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Clear the paper jam, and resend the print job. |
| Error code: | 1101 |
| Display: | Replace part soon. |
| Description: | Data transmission did not finish within the specified time. |
| Causes: | An incompatible loop-back connector is connected to the parallel port, or the loop-back connector is not connected. Use the correct loop-back connector (P/#: G0219350) before the test. |
| Remedy: | Load paper. If the problem remains, then check the paper sensor. |
| Error code: | 1400 ... 140C |
| Display: | No ink left. Press OK and replace ink tank. Ink tank is empty. Replace the ink tank. |
| Description: | Ink tank empty (continued use allowed) The ink tank has run out of ink, but a certain volume of ink is reserved in the subtank. (The reserved volume of ink is put to use after the remaining ink falls below the pin check level.) Displayed only on models having a subtank. (XX: Display applicable colors) Last 2 digits: 00:Bk, 01:Y, 02:M, 03:C, 04:PM, 05:PC, 06:MBk1, 07:MBk2, 08:GY, 09:PGY, 0A:R, 0B:B, 0C:G |
| Remedy: | 1. Replace the tank. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.) |
| Error code: | 1410 ... 141C |
| Display: | No ink tank loaded. Check ink tank. |
| Description: | Ink tank not installed (continued use allowed) The ink tank is not installed but a sufficient volume of ink is left in the subtank. Displayed only on models having a subtank. This occurs in cases such as when the ink tank cover is opened during printing, and the ink tank is removed. (XX: Displays applicable colors) Last 2 digits: 10:Bk, 11:Y, 12:M, 13:C, 14:PM, 15:PC, 16:MBk1, 17:MBk2, 18:GY, 19:PGY, 1A:R, 1B:B, 1C:G |
| Remedy: | 1. Mount the tank. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.) |
| Error code: | 200A |
| Display: | Paper size not detected. Press Load/Eject and reload the paper. Paper size not detected. Reload paper. Paper size not detected. Press OK and reload the paper. |
| Description: | F/W load error Reading/decompressing the firmware has failed. |
| Causes: | Reading / decompressing the firmware has failed. |
| Remedy: | 1. Re-install the firmware. 2. Replace the MAIN BOARD. |
| Error code: | 200B |
| Display: | Paper size not detected. Reload paper. |
| Description: | Internal insufficient memory error The main firmware has a defect. |
| Remedy: | Install the correct main firmware. |
| Error code: | 200C |
| Display: | Paper size not detected. Press Load/Eject and reload the paper. Paper size not detected. Reload paper. Paper size not detected. Lift the release lever and reload the paper. |
| Description: | Servo interrupt watchdog time-out error The servo cannot be controlled. |
| Remedy: | Install the correct main firmware. Replace the MAIN BOARD ASSY . |
| Error code: | 200E |
| Display: | This paper cannot be used. Check supported paper sizes. This paper cannot be used. Check supported paper sizes. Load/Eject: Change Paper |
| Description: | Unknown NMI The CPU has detected an unknown NMI. |
| Remedy: | Replace the Main Board Assy. |
| Error code: | 200F |
| Display: | This paper cannot be used. Check supported paper sizes. This paper cannot be used. Check supported paper sizes. Load/Eject: Change Paper |
| Description: | Paper mismatch (size) Paper is too large -The width and length of paper detected are longer than the supported size (1.5% margin). -Cannot detect the leading edge of paper even when the paper has been fed by 1300 mm for roll paper and by the size mentioned above for cut sheet. -Cannot detect the width of paper even when the paper is fed by the size mentioned above. |
| Remedy: | 1. Check paper conditions (soiling, tear-offs, residual paper chips, residual trimming cuts, folds)/size. 2. Has the paper been fed successfully (without slippage under a load or any influence)? 3. Has the LF adjustment value set correctly? 4. Hasn`t the loaded paper shrunk to below its margin in the particular environment? |
| Error code: | 2010 |
| Display: | Paper loaded askew. Press Load/Eject and reload the paper. |
| Description: | Main motor startup error Main motor is not stabilized within 1 s since the motor is activated. |
| Causes: | Main motor. Engine PWB |
| Remedy: | Main motor 1. To check the motor operation execute U030 Main (main motor). 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Main motor and Engine PWB (YC13) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the main motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2015 |
| Display: | Cannot cut paper. Press Load/Eject and reload the paper. |
| Description: | Cutting failure/jam detected due to a cutting failure An idle cutter unit or a cutter blade that is too blunt to cut sheet has been detected by the paper leading edge detection sequence. |
| Error code: | 2016 |
| Display: | Paper jam. Press Load/Eject and reload the paper. |
| Description: | Jam while picking up, ejecting or printing on paper (A sequence of removing jams with the pinch roller released is required) Virtually all recovery errors that could occur in connection with paper pickup are handled. |
| Causes: | The length in feed direction of the cut paper detected by PAPER ENTRY SENSOR during printing is different from that of which detected during paper feeding.* *The change of the cut paper feed amount due to some reasons such as paper jam may cause this error. |
| Remedy: | 1. Open and close the release lever to reload the paper. 2. Remove the paper once and then refeed it. |
| Error code: | 2017 |
| Display: | Paper size not detected. Lift the release lever and reload the paper. |
| Description: | Paper (right) side detection error 1. Multisensor error on light quantity adjustment 2. The read reference paper edge is 5 mm or more apart from its theoretical position. 3. Cannot locate the edge of reference paper. |
| Causes: | The multi sensor detected that the paper edge at home position side was off 5mm during paper feeding.* *Loading the paper being off the reference position may also cause this error. |
| Error code: | 2018 |
| Display: | Paper size not detected. Lift the release lever and reload the paper. |
| Description: | Paper (left) side detection error The non-reference edge of paper has been located by coarse detection but not by a second round of fine detection. |
| Causes: | The multi sensor failed to detect the away side paper edge during paper feeding.* *Feeding clear films may cause this error. |
| Error code: | 2019 |
| Display: | Cannot cut paper. Lift the release lever and reload the paper. |
| Description: | Cutting failure/jam detected due to a cutting failure An idle cutter unit or a cutter blade that is too blunt to cut sheet has been detected by the paper leading edge detection sequence. Or, cutter unit home position detection was failed. |
| Causes: | This error occurs in the following conditions. • Neither the number of cutter motor rotations nor rotation speed satisfy the specified rotation number and rotation speed during cutting. • The edge detection position is off +/-10mm or more from the reference position in edge detection after cutting. |
| Error code: | 201A |
| Display: | Paper not aligned with right guide. Press OK and then reload the roll paper. |
| Description: | When loading cut sheet, paper (right) side detection was failed. |
| Remedy: | The error is cleared by releasing the release lever. After that, load paper to the correct position. |
| Error code: | 201B |
| Display: | Roll paper is not securely in contact with roll holder. Press OK, then re-attach the roll paper. |
| Description: | When loading roll paper, paper (right) side detection was failed. |
| Remedy: | Paper is ejected automatically, and by pressing the [OK] button the error is cleared. After that, load paper to the correct position. |
| Error code: | 201C |
| Display: | Paper jam Push the release lever back. |
| Description: | While printing, paper width was detected to have fluctuated beyond the predefined value. Failure of detecting right edge of the paper (cut paper, in printing). |
| Remedy: | By releasing the release lever, move to the loading sequence, and load paper to the correct position. |
| Error code: | 201D |
| Display: | Paper jam Remove the paper after cutting at the top of feed slot. Push the release lever back. |
| Description: | While printing, paper width was detected to have fluctuated beyond the predefined value. Failure of detecting right edge of the paper (cut paper, in printing). |
| Remedy: | 1. Cut the paper near the feed slot, and remove the paper. 2. Release the release lever, and load the paper to the correct position. |
| Error code: | 201E |
| Display: | Media Type not compatible with cassette. Check Media Type. Stop: Stop Printing |
| Description: | Paper mismatch (cut sheet) Cassette pickup has been specified for paper that does not support cassette pickup. |
| Remedy: | Check the cassette pick-up setting/ paper type. |
| Error code: | 2405 |
| Display: | Borderless printng not possible. Lift the release lever and reload the paper. Online: Print |
| Description: | Invalid paper loading position (borderless printing) The position at which paper is loaded is unfit for borderless printing. Data with a borderless print specification has been received while the left or right edge of roll paper was off the center of the borderless print idle ejection port at the completion of roll paper pickup. |
| Causes: | Borderless printing is disabled due to the following reasons. The paper is loaded out of position. <When the printer driver is set at [Fit Roll Paper Width]> The multi sensor detects that the paper feed position of the borderless printing supported paper is off 3mm or more from paper edge at the home position side or from the tray for borderless printing at away position side. <When the printer driver is set at other than [Fit Roll Paper Width]> The multi sensor detects that the paper edge at the home position side is off 3mm or more from the reference position. |
| Remedy: | Reload the roll paper. Check spacers |
| Error code: | 2406 |
| Display: | Borderless printng not possible. Check paper size setting. Online: Print Load/Eject: Change Paper |
| Description: | Borderless print data not printable (logic) Borderless print data was received at the start of printing and one or more of the following requirements are met at the same time: -A feeder slot other than one for roll paper has been specified in the data. -A paper type that does not support borderless printing has been set on the data. -Banner printing has been specified on the data at the same time. -A paper size that does not support borderless printing has been specified in a job for which paper had already been fed. |
| Causes: | The borderless print data is received when printing starts. In addition, at least a condition among the following conditions is satisfied. • The paper feeding slot specified in the data is the slot other than roll paper feeding. • The print mode set in the data does not support borderless printing. • Banner printing is selected in the data at the same time. • [Fit Roll Paper Width] is specified and the paper size that does not support borderless printing is specified in the job. • The amount of extra printing for borderless printing in the data is out of standard. |
| Remedy: | Reset the driver and RIP. |
| Error code: | 2407 |
| Display: | Borderless printng not possible. Paper stretched or shrank. Confirm usage cond. of the paper. |
| Description: | It occurs when all of the following conditions are met at start of printing. -Borderless printing data has been received. -Roll paper has been loaded, and its paper width and edge position recognized at loading are within the supported range of borderless printing. -As a result of right/left side edge detection after start of print processing, it was detected as beyond the supported range of borderless printing. |
| Causes: | • The multi sensor detects that the paper edge at the home position side is not positioned within +3mm from the reference paper position. • The printer driver is set at [Fit Roll Paper Width]. Besides, the multi sensor detects that the paper edge at away position side is off 3mm or more from the tray for borderless printing during borderless printing. |
| Remedy: | Reset /replace the roll paper. Confirm and explain usage environment. |
| Error code: | 2408 |
| Display: | Borderless printng not possible. Check supported paper. |
| Description: | At the start of borderless printing, roll paper whose size doesn`t support borderless printing has been loaded. |
| Causes: | When the following condition is satisfied. • The printer driver is set at [Fit Roll Paper Width]. • The printer fed the roll paper in borderless printing unsupported size. |
| Remedy: | Replace with appropriate paper. |
| Error code: | 2409 |
| Display: | Paper position is not suitable for borderless printing. Check paper position. Print to normal printing. Stop printing. |
| Description: | Invalid paper loading position (suspended job/ borderless printing) All of the following conditions were met. -Borderless printing data has been received. -Roll paper whose paper loading position is not suitable for borderless printing has been loaded. -The right or left edge of roll paper is more than 1mm off the prescribed position of the pre-ejection opening. |
| Causes: | When restarting the hold job after replacing the paper with [Replace paper] button, the following cause may disable borderless printing.* • The loaded paper position is off the reference position. *What is “Hold Job?” When “Hold Job?” is selected at [Device settings > Paper-related settings > Detect paper setting mismatch] from the operation panel, the printer saves the printing jobs in HDD without performing printing. These saved jobs are called “Hold Job”. |
| Remedy: | Reload/ replace the roll paper. Check roll paper. 1) Select "Normal printing. (No borderless printing)" and enforce printing. Borderless print setting is ignored. Print with default margin. Default margin depends on selected feeding trays and media type. 2) Select "Stop printing" or press "stop button"to stop printing. 3) Select "replace printing" or release releasing lever. |
| Error code: | 240A |
| Display: | Borderless printing is not possible. Check supported paper. Check paper position. Print to normal printing. Stop printing. |
| Description: | Borderless printing is not possible (suspended job/ unsupported size). All of the following conditions are met. -Borderless printing data has been received. -Roll paper not supporting borderless printing has been loaded. |
| Causes: | When restarting the hold job after replacing the paper with [Replace paper] button, the following cause may disable borderless printing. • The loaded paper is not in the borderless printing supported size. |
| Remedy: | Reload/ replace the roll paper. Check roll paper. 1) Select "Normal printing. (No borderless printing)" and enforce printing. Borderless print setting is ignored. Print with default margin. Default margin depends on selected feeding trays and media type. 2) Select "Stop printing" or press "stop button"to stop printing. 3) Select "replace printing" or release releasing lever. |
| Error code: | 2500 ... 250C |
| Display: | Ink tank is empty. Press OK and replace ink tank. No ink left. Replace ink tank. |
| Description: | Ink tank empty (continued use not allowed) The ink tank has run out of ink. (The reserved volume of ink is put to use after the remaining ink falls below the pin check level.) (In the small LCD, the lower arrow points to the color in question.) The last 2 digits signify applicable colors. 00:Bk, 01:Y, 02:M, 03:C, 04:PM, 05:PC, 06:MBk1, 07:MBk2, 08:GY, 09:PGY, 0A:R, 0B:B, 0C:G |
| Remedy: | 1. Replace the tank. 2. If the problem persists after the tank has been replaced, the remaining ink detection system is at fault (replace the supply unit or check the bundled wires). |
| Error code: | 2510 ... 251C |
| Display: | Ink level is unknown. Check ink level. Press Online to start printing. |
| Description: | Remaining ink level unknown (continued use allowed) The level of ink remaining in the tank is detected when the tank cover is closed. Consumption has exceeded the original ink capacity (mismatch detected). Refill ink may have been used. (In the small LCD, the lower arrow points to the color in question.) The last 2 digits signify applicable colors. 10:Bk, 11:Y, 12:M, 13:C, 14:PM, 15:PC, 16:MBk1, 17:MBk2, 18:GY, 19:PGY, 1A:R, 1B:B, 1C:G |
| Remedy: | Replace the ink tank. |
| Error code: | 2520 ... 252C |
| Display: | No ink tank loaded. Press OK and check ink tank. No ink tank loaded. Check ink tank. |
| Description: | Ink tank not installed (continued use not allowed) On a model that is furnished with a subtank, this error is indicated if the subtank has run out of ink and the state of an ink tank not being installed is detected. The last 2 digits signify applicable colors. 20:Bk, 21:Y, 22:M, 23:C, 24:PM, 25:PC, 26:MBk1, 27:MBk2, 28:GY, 29:PGY, 2A:R, 2B:B, 2C:G |
| Remedy: | 1. Remove and then reinstall the tank. 2. Replace the tank. 3. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.) |
| Error code: | 2540 ... 254C |
| Display: | Ink tank error. Press OK and replace ink tank. |
| Description: | Ink tank ID error The type of ink tank is wrong. The last 2 digits signify applicable colors. 40:Bk, 41:Y, 42:M, 43:C, 44:PM, 45:PC, 46:MBk1, 47:MBk2, 48:GY, 49:PGY, 4A:R, 4B:B, 4C:G |
| Remedy: | 1. Replace the tank. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.) |
| Error code: | 2560 ... 256C |
| Display: | Ink tank error. Press OK and replace ink tank. |
| Description: | Ink tank EEPROM error There is an error in tank EEPROM. The last 2 digits signify applicable colors. 60:Bk, 61:Y, 62:M, 63:C, 64:PM, 65:PC, 66:MBk1, 67:MBk2, 68:GY, 69:PGY, 6A:R, 6B:B, 6C:G |
| Remedy: | 1. Replace the tank. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.) |
| Error code: | 2570 ... 257C |
| Display: | Ink insufficient. Press OK and replace ink tank. |
| Description: | Ink tank short on ink A suction operation was attempted, but there is not enough ink left in the tank for the operation (iPF8000 series, iPF9000 series). Reference) About 5 mL to 40 mL of ink may have been left in the tank when this warning occurs. 70:Bk, 71:Y, 72:M, 73:C, 74:PM, 75:PC, 76:MBk1, 77:MBk2, 78:GY, 79:PGY, 7A:R, 7B:B, 7C:G |
| Remedy: | 1. Replace the tank. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.) |
| Error code: | 2580 ... 258C |
| Display: | Ink insufficient. Press OK and replace ink tank. Ink insufficient. Replace ink tank. |
| Description: | Ink tank short on ink A suction operation was attempted, but there is not enough ink left in the tank for the operation. (In the small LCD, the lower arrow points to the color in question.) Reference) About 5 mL to 40 mL of ink may have been left in the tank when this warning occurs. 80:Bk, 81:Y, 82:M, 83:C, 84:PM, 85:PC, 86:MBk1, 87:MBk2, 88:GY, 89:PGY, 8A:R, 8B:B, 8C:G |
| Remedy: | 1. Replace the ink. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.) |
| Error code: | 2590 ... 259C |
| Display: | Ink insufficient. Press OK and replace ink tank. Ink insufficient. Replace ink tank. |
| Description: | Ink tank short on ink A print operation was attempted, but there is not enough ink left in the tank for the operation. (In the small LCD, the lower arrow points to the color in question.) Reference) About 5 mL to 40 mL of ink may have been left in the tank when this warning occurs. 90:Bk, 91:Y, 92:M, 93:C, 94:PM, 95:PC, 96:MBk1, 97:MBk2, 98:GY, 99:PGY, 9A:R, 9B:B, 9C:G (*1) 259C: 03810208-259C |
| Remedy: | 1. Replace the ink. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.) |
| Error code: | 259C ... 25A8 |
| Display: | Ink insufficient. Press OK and replace ink tank. Ink insufficient. Press OK and replace ink tank. |
| Description: | Ink insufficient in inktank. The amount of ink left in the inktank is insufficient for printing. (In the small LCD, the lower arrow points to the correspondence color.) Reference) There are the cases that about 5ml to 40ml ink is left in a inktank at warning occurs. 9C:Bk,9D:C,9E:M,9F:Y,A0:PC,A1:PM,A 2:MBk1,A3:MBk2, A4:GY,A5:PGY,A6:R,A7:G,A8:B (*2) 259C: 03810104-259C |
| Remedy: | 1. Replace inktank 2. Failure of detecting the ink amount left in the inktank. (Replace the supply unit /check the bundled wires.) |
| Error code: | 25B7 |
| Display: | Close the ink tank cover. Unable to detect ink level correctly. Unable to detect ink level correctly. |
| Description: | The remaining ink falls below the pin check level while ink tank cover is open. |
| Remedy: | Close the ink tank cover. Note) It does not recover if the cover is open when replacing the ink tank with a valid one. If removing the ink tank with lower ink remains (LIR) than Supply Pin in this situation, an error is detected. Also when keeping printing in this situation, if empty subtank corresponding to the ink tank with LIR is detected, the error shifts from ink tank with LIR to empty subtank. |
| Error code: | 260E |
| Display: | Hardware error. 03130031-260E Turn off printer, wait, then turn on again. |
| Description: | Gap detection failure Carriage gap calibration has not been carried out, or gap detection is disabled by corrupt calibration data. |
| Remedy: | 1. Check to see if the multisensor reference plate (white patch for batch correction) is not soiled and perform GAP CALIB (if soiled, adjust the part after replacing it). 2. Replace the multisensor and perform GAP CALIB. 3. Replace the carriage unit and perform GAP CALIB. |
| Error code: | 260F |
| Display: | Gap error. Turn off printer. |
| Description: | Gap reference plane error Request to replace an abnormal reference plane sheet (only in Service mode). |
| Remedy: | Check the multisensor reference plate (for soiling and faulty mounting). |
| Error code: | 2800 |
| Display: | No printhead Install printhead. |
| Description: | Printhead [X] non-existing [X]: Double-head model : The R-head does not exist. Single-head model: The head does not exit. |
| Causes: | The access cover is closed though no print head is detected. |
| Remedy: | 1. Check the status of the printhead mounted. 2. Mount the long flexible cable and check the status of the cable being locked. |
| Error code: | 2801 |
| Display: | Printhead error Open top cover and replace the printhead. |
| Description: | Power ON JAM 1 (*2) |
| Causes: | TOP Sensor Residual |
| Remedy: | PS2 Multi-purpose Tray |
| Error code: | 2802 |
| Display: | Printhead error Open top cover and replace the printhead. |
| Description: | Power ON JAM 1 (*2) |
| Causes: | TOP Sensor Residual |
| Remedy: | PS2 Cassette 1 |
| Error code: | 2803 |
| Display: | Printhead error Open top cover and replace the printhead. |
| Description: | Power ON JAM 1 (*2) |
| Causes: | TOP Sensor Residual |
| Remedy: | PS2 Cassette 2 |
| Error code: | 2804 |
| Display: | PHeads: wrong pos. Open top cover and check the printhead positions. |
| Description: | Printheads mounted in L/R opposite positions L printhead is mounted on R side. |
| Remedy: | Replace with a valid printhead. (An error has occurred but the printhead itself is not damaged, so communication has been maintained properly.) The L/R printheads cannot be interchanged. |
| Error code: | 2805 |
| Display: | Printhead error. Open top cover and replace the printhead. |
| Description: | The specified time has been passed in lower printhead temperature than the specified temperature. |
| Remedy: | 1. Acclimate to room temperature. 2. Replace the printhead. 3. Replace the main controller PCB. 4. Replace the CR board. |
| Error code: | 2807 |
| Display: | PHeads: wrong pos. Open top cover and check the printhead positions. |
| Description: | Power ON JAM 1 (*2) |
| Causes: | TOP Sensor Residual |
| Remedy: | PS2 Registration Area to Drum Area |
| Error code: | 2808 |
| Display: | No left printhead Install left printhead. |
| Description: | Power ON JAM 1 (*2) |
| Causes: | Fixing Delivery Sensor Residual |
| Remedy: | PS13 Drum Area to Fixing Area |
| Error code: | 2809 |
| Display: | Left printhead error Open top cover and replace the left printhead. |
| Description: | Power ON JAM 1 (*2) |
| Causes: | Delivery Tray Full Sensor Residual |
| Remedy: | PS4 Fixing Area to Delivery Area |
| Error code: | 280A |
| Display: | Left printhead error Open top cover and replace the left printhead. |
| Description: | Invalid printhead L has been mounted. |
| Remedy: | Replace with a valid printhead. (An error has occurred but the printhead itself is not damaged, so communication has been maintained properly.) |
| Error code: | 280B |
| Display: | Left printhead error Open top cover and replace the left printhead. |
| Description: | Printhead L EEPROM error |
| Remedy: | Replace the printhead. |
| Error code: | 280C, 280D, 280E |
| Display: | PHead needs cleaning. Press Online to clear error. The printhead requires cleaning. The printhead requires cleaning. Online=Print Stop=Stop Printing |
| Description: | Printhead R non-ejection warning (Check printhead) Printing paused/ continued printing allowed The level of error is decided as shown in the table below, based on the number of non-ejecting nozzles per color (per chip) and the number of nozzles unable to back up. Depending on the firmware version, the specifications vary as shown in the table below. |
| Remedy: | 1. Check image quality. (Unless there are problems with the image quality, there is no need to replace the printhead.) 2. Replace the printhead. |
| Error code: | 2811 |
| Display: | Printhead error Open top cover and replace the left printhead. |
| Description: | Incompatible printhead version |
| Remedy: | Replace with a valid printhead. (An error has occurred but the printhead itself is not damaged, so communication has been maintained properly.) |
| Error code: | 2812 |
| Display: | Right printhead error Open top cover and replace the right printhead. |
| Description: | Incompatible printhead R version |
| Causes: | Installation of inappropriate print head version. |
| Remedy: | Replace with a valid printhead. (An error has occurred but the printhead itself is not damaged, so communication has been maintained properly.) |
| Error code: | 2813 |
| Display: | Left printhead error Open top cover and replace the left printhead. |
| Description: | Incompatible printhead L version |
| Remedy: | Replace with a valid printhead. (An error has occurred but the printhead itself is not damaged, so communication has been maintained properly.) |
| Error code: | 2816 |
| Display: | Maintenance cartridge problem. Replace the maintenance cartridge. |
| Description: | Maintenance cartridge EEPROM error Communication is enabled but the information is corrupted. <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning. |
| Causes: | At maintenance cartridge EEPROM accessing, communication error occurs. |
| Remedy: | Replace the maintenance cartridge. |
| Error code: | 2817 |
| Display: | Maintenance cartridge problem. Replace the maintenance cartridge. |
| Description: | Maintenance cartridge ID error A maintenance cartridge for another model has been mounted. <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning. |
| Causes: | At maintenance cartridge EEPROM accessing, the maintenance cartridge that had been installed to the other model is detected. |
| Remedy: | Replace the maintenance cartridge. (The maintenance cartridge was capable of normal communication when the error occurred.) |
| Error code: | 2818 |
| Display: | No maintenance cartridge. Check the maintenance cartridge. |
| Description: | Maintenance cartridge not found Cannot communicate, or cannot detect a maintenance cartridge. <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning. |
| Causes: | No maintenance cartridge is detected. |
| Remedy: | Remove and reinstall, or replace the maintenance cartridge. |
| Error code: | 2819 |
| Display: | Maintenance cartridge full. Replace the maintenance cartridge. |
| Description: | Maintenance cartridge full Maintenance cartridge full is detected from the dot count and the usage period (drying time). <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning. |
| Causes: | At maintenance cartridge EEPROM accessing, the maintenance cartridge is detected to be full. |
| Remedy: | Replace the maintenance cartridge. Reference) The absorber may appear whitish or weigh light, depending on the usage conditions. |
| Error code: | 281A |
| Display: | Prepare for maint cart replacement |
| Description: | Maintenance cartridge near-full (continued usage allowed) Near-full has been detected from the dot count and the usage period (drying time). <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning. |
| Causes: | At maintenance cartridge EEPROM accessing, the value indicates little capacity is left in the maintenance cartridge. |
| Remedy: | Prepare a maintenance cartridge. |
| Error code: | 281B |
| Display: | No MaintenanceCartridge capacity. Replacethe maintenancecartridge. |
| Description: | The maintenance cartridge before cleaning does not have an enough capacity (reusable). Near-full has been detected from the dot count and the usage period (drying time). <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning. |
| Causes: | Insufficient capacity in the maintenance cartridge for cleaning is detected when accessing to the maintenance cartridge EEPROM. |
| Remedy: | Replace the maintenance cartridge. The maintenance cartridge can be put to reuse after the end of cleaning. Reference) The absorber may appear whitish or weigh light, depending on the usage conditions. |
| Error code: | 2820 |
| Display: | Cannot adjust printhead. Press Online to clear the error and readjust printhead. |
| Description: | Intermediate transfer belt motor steady-state error After transfer motor is stabilized, the ready signal is at the H level for 5 s continuously. The counter value obtained by timer capture is lower than 2200 for 10 times in a row. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective transfer motor. Defective engine PWB. |
| Remedy: | Transfer motor 1. To check the motor operation, execute U030 Belt Meand. 2. Rotate the roller, driving gear by the hand and check that they are not unusually loaded. 3. Clean the intermediate transfer belt unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Transfer motor and Feed PWB 1(YC13) Feed PWB 1(YC2) and Engine PWB (YC5) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the Transfer motor. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2821 |
| Display: | Cannot adjust band. Press Online to clear the error and readjust the band. |
| Description: | LF unadjustable A detected value has gone out of bounds while performing automatic band adjustment. |
| Remedy: | 1. Adjustment is not possible with transparent/semi-transparent paper. Replace with paper having similar substrate and perform automatic band adjustment or manual adjustment. 2. Make detailed band adjustment (automatic). 3. Check the nozzle check pattern. 4. Initialize the system settings/paper preferences and then add additional paper and perform automatic band adjustment (detailed). If the paper preferences are initialized, all the paper setting would be reset to their factory defaults. |
| Error code: | 2822 |
| Display: | Cannot adjust eccentric. Press Online to clear the error. |
| Description: | Eccentricity uncorrectable (which does not occur when in User mode) A detected value has gone out of bounds while making adjustment. |
| Remedy: | 1. Check the paper type: Replace with photo glossy paper (UF120). 2. Check the paper for soiling, tear and other defects. Having run LF tuning, update the additional paper. |
| Error code: | 2823 |
| Display: | Hardware error. 03010000-2823 Turn off printer, wait, then turn on again. |
| Description: | Head check error |
| Error code: | 2824 |
| Display: | Cannot adjust optic axis. Press Online to clear the error. |
| Description: | Optical axis unadjustable (which does not occur when in User mode) An adjustment pattern has not been printed. The optical axis deviates from the correct position by -/+3 mm or more. |
| Remedy: | Check the paper (paper type check). |
| Error code: | 2825 |
| Display: | This type of media is not compatible with HP-GL/2. |
| Description: | Paper type not compatible with HP-GL/2 has been specified. |
| Remedy: | Check the paper. |
| Error code: | 2826 |
| Display: | LFNG XXX XXX XXX XXX press OK key (XXXX is a measured value.) |
| Description: | When executing LF unevenness auto diagnostic processing, the multisensor read value has gone outside the predefined scope (Service mode only). |
| Remedy: | Check the paper. Check the multisensor. |
| Error code: | 2827, 2828, 2829 |
| Display: | Execute printhead cleaning. If this message is still displayed, replace Printhead. |
| Description: | Printhead non-discharge error (Replace printhead/ continued printing not allowed) At start of printing the number of nonejecting nozzles is more than 320 per color (1 chip). 2827: Both L and R, or single printhead model 2828: R printhead 2829: L printhead * For the detailed head non-ejection errors, see section 280C. (If Setting of SERVICE MODE > SETTING >HEAD WARNING is off, the error code is 280E.) |
| Remedy: | 1. Execute cleaning. 2. Replace printhead. |
| Error code: | 282A |
| Display: | CR MOTOR TUNING ERROR :PRESS OK |
| Description: | Carriage motor identification processing (rotation adjustment) failed (for Service mode) |
| Remedy: | Error is cleared by OK button. 1. Check installation of carriage or carriage belt. 2. Clean the carriage main rail (Do not oil it.) 3. Replace the carriage motor. |
| Error code: | 282B |
| Display: | CR VIBRATION ERROR :PRESS OK |
| Description: | When processing carriage motor identification (rotation adjustment), carriage vibration has been detected (for Service mode). |
| Remedy: | Error is cleared by OK button. 1. Check installation of carriage or carriage belt. 2. Clean the carriage main rail (Do not oil it.) 3. Replace the carriage motor. |
| Error code: | 282D |
| Display: | Left printhead error. Turn off printer, wait, then turn on again. |
| Description: | Printhead error detected (L head only). Displayed when an abnormal temperature rise of printhead has been detected to prompt you to restart. |
| Remedy: | After restarting, replace the printhead L. |
| Error code: | 282E |
| Display: | Printhead error Turn off printer, wait, then turn on again. |
| Description: | Temperature rising detected by particular ink pre-injection before printing was judged abnormal. |
| Remedy: | 1. Replace the printhead. 2. Replace the main controller PCB. |
| Error code: | 2830 |
| Display: | Left printhead error. Open top cover and replace the left printhead. |
| Description: | Developing motor K error The developing motor K ready input is not given for 5 seconds during the developing motor K is ON. |
| Causes: | Defective harness between developing motor K and engine PWB (YC26), or improper connector insertion. Defective drive transmission system of the developing motor K. Improper installation intermediate transfer unit. Defective developing motor K. Defective engine PWB. |
| Remedy: | Defective harness between developing motor K and engine PWB (YC26), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Defective drive transmission system of the developing motor K. Check if the gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Improper installation intermediate transfer unit. Check the installation of the intermediate transfer unit and reinstall them if necessary. Defective developing motor K. Replace the developing motor K. Defective engine PWB. Replace the engine PWB. |
| Error code: | 2832 |
| Display: | Hardware error 03130031-2832 Turn off printer, wait, then turn on again. |
| Description: | VHT leak detection error of right printhead or of a single printhead, in case of VHT exceeds rated value or falls below the rated value. |
| Remedy: | iPF6300/6400 Series iPF8300/8400/9400 Series Replace right or left printhead. |
| Error code: | 2833 |
| Display: | Hardware error 03130031-2833 Turn off printer, wait, then turn on again. |
| Description: | VHT leak detection error of left printhead, in case of VHT exceeds rated value or falls below the rated value. |
| Remedy: | iPF6300/6400 Series iPF8300/8400/9400 Series Replace right or left printhead. |
| Error code: | 2834 |
| Display: | Unknown printhead. Open top cover and re-install printhead. |
| Description: | Printhead contact failure is detected after the printhead installation. |
| Remedy: | 1. Remove and reinstall the printhead. 2. Replace the printhead. 3. Replace the carriage unit. 4. Replace the main controller PCB. |
| Error code: | 2835 |
| Display: | Cannot recognize print head R. Open the top cover and reinsert the printhead R. |
| Description: | Printhead contact failure is detected after the printhead installation. |
| Remedy: | 1. Remove and reinstall the printhead. 2. Replace the printhead. 3. Replace the carriage unit. 4. Replace the main controller PCB. |
| Error code: | 2836 |
| Display: | Cannot recognize print head L. Open the top cover and reinsert the printhead L. |
| Description: | Printhead contact failure is detected after the printhead installation. |
| Remedy: | 1. Remove and reinstall the printhead. 2. Replace the printhead. 3. Replace the carriage unit. 4. Replace the main controller PCB. |
| Error code: | 2901 |
| Display: | Mail box nearly full. Delete unwanted data. The mail box is nearly full. Delete |
| Description: | Delivery Delay Jam |
| Causes: | Fixing Delivery Sensor SR3 |
| Remedy: | Pickup Cassette of the host machine |
| Error code: | 2902 |
| Display: | Mail box full. Now printing without saving data. |
| Description: | Power ON JAM 2 (*2) |
| Causes: | TOP Sensor Residual |
| Remedy: | PS2 Cassette 1 |
| Error code: | 2905 |
| Display: | Mail box full. Delete unwanted data on your computer to resume printing. Press Stop to cancel printing. The mail box is full. Delete unwanted data from your computer to continue. |
| Description: | A job save has been executed when the available size of the permanent area of the hard disk space was lost. Cancel the job. |
| Causes: | The value indicates capacity is full in the hard disk. |
| Remedy: | Reorganize data. |
| Error code: | 2906 |
| Display: | Mail box full. Cannot save. Delete unwanted data on your computer to resume printing. Press Stop to cancel printing. Too many jobs for mail box. Delete unwanted data from your computer to continue. |
| Description: | The 101st job has been received when 100 jobs are already saved in the permanent area of the hard disk space. |
| Causes: | The number of files saved in the hard disk reaches the max. |
| Remedy: | Reorganize data. |
| Error code: | 2907 |
| Display: | Mail box full. Delete unwanted data. Maximum jobs stored. Delete unwanted data. |
| Description: | Delivery Delay Jam |
| Causes: | Fixing Delivery Sensor SR3 |
| Remedy: | Registration to Drum Area |
| Error code: | 2908 |
| Display: | Hard disk error. Press OK to reformat |
| Description: | Delivery Delay Jam |
| Causes: | Fixing Delivery Sensor SR3 |
| Remedy: | Drum to Fixing Area |
| Error code: | 2909 |
| Display: | File read error. Turn off printer, wait a while, and turn it on again. Invalid files will be deleted. |
| Description: | Delivery Delay Jam |
| Causes: | Fixing Delivery Sensor SR3 |
| Remedy: | Fixing to Delivery Area |
| Error code: | 290A |
| Display: | Hardware error. 03130031-290A Turn off printer, wait, then turn on again. |
| Description: | HDD not connected. HDD was not detected at startup. |
| Remedy: | Connect the HDD/ Check the harness. Replace the HDD. |
| Error code: | 2918 |
| Display: | Power On Again Cassette Sensor Detection Error |
| Description: | Cassette detection sensor detection failure (cassette presence/absence sensor) No cassette has been detected during cassette pickup. |
| Remedy: | 1. Check to see if the cassette itself is properly loaded. 2. Check and replace the sensor (I/O mode). |
| Error code: | 291A |
| Display: | Roll sensor cannot detect. Turn on printer again. |
| Description: | Roll sensor detection failure Could not detect the roll unit. |
| Remedy: | 1. Check the roll unit, and remove, install or replace the roll unit. 2. Check I/O mode (roll unit detection). |
| Error code: | 291B |
| Display: | Hardware error. 03130031-291B Turn off printer, wait, then turn on again. |
| Description: | Lift shift timeout A lift operation has been executed, but no sensor has been detected or a sensor has remained detected. |
| Remedy: | 1. Switch off the printer, then back on. 2. The carriage cannot travel to the lift drive position. 3. The lift drive cam is not engaged. 4. Faulty lift drive sensor 5. Faulty lift drive motor |
| Error code: | 291D |
| Display: | Hardware error. 03130031-291D Turn off printer, wait, then turn on again. |
| Description: | Spur cam sensor detection failure |
| Remedy: | Check the spur cam sensor in I/O mode. -If OK, check the lifter drive system. -If NG, replace the sensor. |
| Error code: | 2920 |
| Display: | Media Take-up error. Check the paper. Press Online to clear error. |
| Description: | Cannot take up paper An error check has been made on paper after the paper had been fed 1850 mm, but the media take-up unit was not driven at all in that interval (up to about 3700 mm [when run immediately after the start of detection]). |
| Causes: | The paper feed amount by ACTIVE ROLL UNIT is insufficient against the paper feed amount by PAPER FEED MOTOR. (example: lack of torque, electrical failure of the motor, etc.) |
| Remedy: | 1. Check to see if the media take-up unit is switched on with the lock lever down. 2. Check the connection between the main unit and the media take-up unit. 3. Check to see if the wait roller is properly set. 4. Check to see if the media take-up detection sensor is shielded by paper when it is presented. 5. Faulty media take-up detection sensor 6. Faulty Media take-up motor |
| Error code: | 2921 |
| Display: | Rewinding error. Check for jam at indicated position. Press Online to clear error. Rewinding error. Check for jam at indicated position. |
| Description: | Continued rewinding error The media take-up unit has continued rewinding for 10 seconds, with the media take-up paper detection sensor turned on, at printer power-on and at the start of printing. |
| Causes: | The paper feed amount by ACTIVE ROLL UNIT is too much against the paper feed amount by PAPER FEED MOTOR. (example: no paper, gear damage, out-of-control motor, etc.) |
| Remedy: | 1. Check to see if any obstacle is placed at the media take-up paper detection sensor position. 2. Faulty media take-up paper detection sensor 3. Faulty media take-up button 4. Faulty media take-up motor |
| Error code: | 2930 |
| Display: | Cutting Mode not Automatic. Remove stacker and print again or cancel and change settings. Print again Cancel |
| Description: | Stacker is not ready. - The power supply is not supplied to the stacker. - The distance between the stacker and printer is not appropriate. - The stacker is not joined. - Stacker initial error |
| Remedy: | Continue or stop the print. If the preparation of the stacker isn`t performed, the error occurs again. |
| Error code: | 2931 |
| Display: | Cutting Mode not Automatic. Remove stacker and print again or cancel and change settings. Print again Cancel |
| Description: | When the stacker is usable condition, the printing has been started at the setting of cut-off or cutline print or eject or manual mode. |
| Remedy: | Print again after separating the distance between the stacker and printer enoughly, or cancel print. |
| Error code: | 2E00 |
| Display: | Load Roll Media |
| Description: | Paper mismatch (roll paper) No roll paper have been fed when a job with a roll paper specification is received. |
| Remedy: | Load roll paper. |
| Error code: | 2E01 |
| Display: | Roll printing is selected. Press Load/Eject and load a roll. |
| Description: | Paper mismatch (roll paper) Roll Paper have not been fed when an internal print job having a roll paper specification started (during internal printing). |
| Remedy: | Load roll paper. |
| Error code: | 2E02 |
| Display: | Sheet printing is selected. Press Load/Eject and load sheets. |
| Description: | Paper mismatch (cut sheet) No cassette paper has been loaded when data having a cut sheet specification is received. |
| Causes: | The cut sheet is not fed when receiving the job selecting cut sheet. Or “No sheets.” is detected after starting printing. |
| Remedy: | Load cut sheet. |
| Error code: | 2E03 |
| Display: | Load Papr in Cas Press Online. |
| Description: | Paper mismatch (cut sheet) Not cut sheet have been loaded in cassettes when data having a cassette specification is received. |
| Remedy: | Feed paper as instructed by the onscreen guidance. |
| Error code: | 2E04 |
| Display: | Manual(Front) (Paper type) (Paper size) Load Paper Stop Printing |
| Description: | Paper mismatch (cut sheet) No manually fed paper has been fed when a job having a front paper feed specification is received. |
| Remedy: | Feed paper manually from the front as instructed by the on-screen guidance. |
| Error code: | 2E05 |
| Display: | Manual(Top) (Paper type) (Paper size) Load Paper Stop Printing |
| Description: | Paper mismatch (cut sheet) No manually fed paper has been fed when a job having a top paper feed specification is received. Paper mismatch (cut sheet) Not cut sheet have been loaded in cassettes when data having a cassette specification is received.(When paper type/ size is not determined) |
| Remedy: | Feed paper manually from the top as instructed by the on-screen guidance. Load cut sheet. |
| Error code: | 2E08 |
| Display: | Wrong paper size. Check paper size setting on computer. Online: Print Stop: Stop Printing |
| Description: | Paper mismatch (size) (roll paper) The width of data and that of the actually loaded paper do not match. |
| Causes: | The paper roll width indicated in the print job and the roll paper width loaded on the printer are not matched. |
| Remedy: | Check the paper that is actually loaded on the printer and the paper size setting of the driver. |
| Error code: | 2E09 |
| Display: | Insufficient paper for job Online: Print Stop: Stop Printing Load/Eject: Change Paper |
| Description: | Short on roll paper All of the following conditions have been met at the start of printing: -[ON] has been selected for [Remaining Roll Paper Detection]. -Among the paper size settings coded in the print data, the paper length exceeds the remaining length of roll paper. |
| Causes: | The printer, which is selecting “Enable” at [Manage remaining roll amount], receives a print job that requires the longer paper size than the remaining paper length. |
| Remedy: | Replace the roll paper. |
| Error code: | 2E0A |
| Display: | Roll printing is selected, but sheets are loaded. Press Load/Eject and remove the sheets. |
| Description: | Paper mismatch (roll paper) Print data having a roll paper print specification has been received at the completion of manual feed paper pickup. |
| Causes: | The printer receives roll paper print data while feeding has completed with cut sheet. |
| Remedy: | Check the paper that is actually loaded on the paper and the paper feed setting of the driver. |
| Error code: | 2E0B |
| Display: | Cassette printing is selected. Press Load/Eject and remove manually loaded sheets. |
| Description: | Paper mismatch (cut sheet) Print data having a cassette print specification has been received at the completion of manual feed paper pickup. |
| Causes: | The printer receives cut sheet print data while feeding has completed with roll paper. |
| Remedy: | Check the paper that is actually loaded on the paper and the paper feed setting of the driver. |
| Error code: | 2E0C |
| Display: | Manual printing is selected, but a roll is loaded. Press Load/Eject and remove the roll. |
| Description: | Paper mismatch (cut sheet) 1. Print data having a manual feed print specification has been received at the completion of roll paper pickup. 2. Print data having a manual feed print specification has been received when there is roll paper printout. 3. Cut sheet data has been received when the media take-up unit is in use. |
| Causes: | The printer receives the print data selecting cut sheet printing while take-up unit is in use. |
| Remedy: | Check the paper that is actually loaded on the paper and the paper feed setting of the driver. |
| Error code: | 2E0E |
| Display: | No Roll Feed Unit. Turn printer off and install roll feed unit. |
| Description: | Roll paper unit not installed The unit has received print data having a roll paper print specification when it had started without a roll unit being connected to it. |
| Causes: | The lower roll paper feeding has been completed, but the printed roll paper is still on the lower roll unit. In this state, the printer receives the print data that requires to select the upper roll paper setting. • Selecting gNoh or gPrint cut Guidelineh in [Automatic Cutting] setting for lower roll printing may cause this error. |
| Remedy: | 1. Check the roll unit, and remove, install or replace the roll unit. 2. Check I/O mode (roll unit detection). |
| Error code: | 2E0F |
| Display: | Top cover is open. Turn off printer, wait a while, and turn it on again. |
| Description: | The top cover is abnormally open. |
| Causes: | The purpose of the lower roll unit setting is other than paper feeding, when printing is commanded to the lower roll unit. |
| Remedy: | Check the cover. Check the sensor (I/O mode). |
| Error code: | 2E10 |
| Display: | Ink tank cover is open. Turn off printer, wait a while, and turn it on again. |
| Description: | Ink tank cover error open (continued use allowed) The ink tank cover opened while performing any operation, such as printing and suctioning. |
| Causes: | While "Roll Paper" is set in [Media Settings], feeding of cut paper is detected. |
| Remedy: | Close the ink tank cover. Check the sensor (I/O mode). |
| Error code: | 2E11 |
| Display: | Carriage Cover is open. |
| Description: | Carriage cover open error A carriage cover open has been detected. |
| Causes: | While "Cut Paper" is set in [Media Settings], feeding of roll paper is detected. |
| Remedy: | Close the carriage cover. Check the sensor (I/O mode). |
| Error code: | 2E12 |
| Display: | Rel lever is in wrong position. Turn off printer, wait, then turn on again. |
| Description: | Faulty release lever The state of the release lever up (released) has been detected. |
| Remedy: | Push down the release lever. Check the sensor. |
| Error code: | 2E14 |
| Display: | Wrong paper size. Check paper size setting on computer. Online: Print Stop: Stop Printing |
| Description: | Paper mismatch (size or width) The paper size specified for the [Print to meet the paper width] setting of the driver on receiving print data and the width of the roll paper actually fed did not match. |
| Remedy: | Check the paper that is actually loaded on the printer and the paper size setting of the driver. |
| Error code: | 2E15 |
| Display: | Wrong paper feed slot for this paper type. Press Load/Eject and reload the paper. |
| Description: | Paper mismatch (type) A paper type that cannot be fed from the specified feeder slot has been specified. |
| Causes: | The media type selected in the job is different from the actual fed media. |
| Remedy: | Check the feeder slot/cassette pick-up setting. |
| Error code: | 2E16 |
| Display: | Wrong paper type. Check paper type setting on computer. Online: Print Stop: Stop Printing |
| Description: | Paper mismatch (type) The data type defined in the data and the type of actually loaded paper do not match. Following the transmission of data in the GARO format, all of the following conditions have been met at the start of printing: -The paper type that has been set in the job and the type of actually fed paper do not match. -[Stop] has been selected for [Paper Mismatch Detection]. |
| Remedy: | Check the paper that is actually loaded on the printer and the driver paper type setting. |
| Error code: | 2E17 |
| Display: | No cassette detected. Check the cassette. |
| Description: | Cassette not installed |
| Remedy: | 1. Check to see if the cassette itself is properly loaded. 2. Check and replace sensor (I/O mode). |
| Error code: | 2E18 |
| Display: | Cannot load. Press Load/Eject and reload the paper. |
| Description: | Paper not fed as far as the platen |
| Error code: | 2E19 |
| Display: | Cannot load. Press Load/Eject and reload the paper. |
| Description: | Feeding error LF out of synchronization for cut sheet |
| Remedy: | Refeed the paper. |
| Error code: | 2E1A |
| Display: | Cannot load. Press Load/Eject and reload the paper. |
| Description: | Feeding error LF out of synchronization for cut sheet |
| Remedy: | Refeed the paper. |
| Error code: | 2E1B |
| Display: | The roll is empty. Load/Eject: Change Paper |
| Description: | No roll paper available (trailing edge of roll paper detected) -Trailing edge of paper has been detected by paper sensor in a roll paper operation. -LF out of synchronization on roll paper. (Detected the spool no longer rotating.) |
| Causes: | PAPER ENTRY SENSOR detects the paper end during feeding the roll paper. |
| Remedy: | 1. Replace the roll paper. 2. Check paper sensor R (I/O mode). 3. Is the paper fed successfully (under a negative load or any other influence)? |
| Error code: | 2E1C |
| Display: | Paper jam. Press Load/Eject and reload the paper. |
| Description: | Jam while ejecting paper (A sequence of removing jams with the pinch roller released is required) A jam has been detected while ejecting paper. |
| Causes: | LOWER PAPER ENTRY SENSOR detects the paper end during feeding the lower roll paper. |
| Remedy: | 1. Open and close the release lever to reload the paper. 2. Remove the paper once |
| Error code: | 2E1D |
| Display: | Cannot load. Press Load/Eject and reload the paper. |
| Description: | Feeding error LF out of synchronization for cut sheet |
| Remedy: | Refeed the paper. |
| Error code: | 2E1F |
| Display: | Cannot print as specified. Press Load/Eject and replace paper with A2/ 16.6"x23.4" (vertical) or larger |
| Description: | Paper mismatch (size) The second and subsequent sheets of paper have been fed as a paper size different from the first sheet when adjustment was made with cut sheet. The paper size setting in effect at the start of an internal print session has fallen below the minimum size specified for that internal print session. [XXX x YYY]: Required minimum size The second and subsequent sheets of paper have been fed as a paper size different from the first sheet when adjustment was made with cut sheet. [XXX x YYY]: Required minimum size |
| Remedy: | Check the paper that is actually loaded on the printer and the paper size setting of the driver. |
| Error code: | 2E20 |
| Display: | Wrong paper type. Lift the release lever and reload the paper. Stop: Stop Printing |
| Description: | Paper mismatch (type) (on adjustment) The second and subsequent sheets of paper have been fed as a paper type different from the first sheet when LF adjustment was made from a cassette. |
| Causes: | When adjusting feeding system with cut sheets, page2 or after with different media type or size from that of page1 is fed, and appropriate adjustment is considered to be disabled. |
| Remedy: | Equalize the paper types for the first and second sheets with each other in adjustment printing. |
| Error code: | 2E21 |
| Display: | Hardware error. 03130000-2E21 Turn off printer, wait, then turn on again. |
| Description: | IEEE1394 interface error Any error has been detected while initializing IEEE1394 at startup. |
| Causes: | When adjusting the print head position with cut sheets, page2 or after with different media type or size from that of page1 is fed, and appropriate adjustment is considered to be disabled. |
| Remedy: | 1. Restart the printer. 2. Remove and reinsert the IEEE1394 board and then restart the printer. 3. Replace the IEEE1394 board. |
| Error code: | 2E22 |
| Display: | Media Type not compatible with cassette. Check Media Type. Stop: Stop Printing |
| Description: | Paper mismatch (cut sheet) Cassette pickup has been specified for paper that does not support cassette pickup |
| Remedy: | Check the cassette pick-up setting/ paper type |
| Error code: | 2E23 |
| Display: | Hardware error. 03130031-2E23 Turn off printer, wait, then turn on again. |
| Description: | Cutter unit failure At startup or completion of paper jam handling, when attempting to get the cutter which is in other position than HP back to HP, the home position sensor timed out without response. |
| Remedy: | 1. Remove paper slip (foreign matter) attached to the cutter home position sensor. 2. Check the cutter driving circuit and the cutter unit. When FU3902 blows out on PF510/ 5100/610, -Replace the main controller PCB When FU2802 blows out on iPF6300 series/ 6400 series -Replace the main controller PCB. |
| Error code: | 2E24 |
| Display: | Roll feed unit err Turn off printer and check roll feed unit |
| Description: | Faulty roll paper unit Failed to detect the cam in the roll unit while no paper was loaded. |
| Remedy: | Check the roll cam sensor (I/O mode). |
| Error code: | 2E25 |
| Display: | Cannot detect papr Remove paper and press Load/Eject. Cannot detect papr Remove paper and press OK. |
| Description: | Jam while picking up, ejecting or printing on paper (JAM2). After loading of roll paper or cut sheet was loaded successfully, Paper detection sensor/ Media sensor sensor detected no paper (JAM2). |
| Error code: | 2E27 |
| Display: | Cannot load. Press Load/Eject and reload the paper. Paper jam. Press Load/Eject and reload the paper. |
| Description: | Feeding error (nip release required) LF out of synchronization (feed motor won`t rotate) has been detected. Jam while picking up, ejecting or printing on paper (A sequence of removing jams with the pinch roller released is required)(JAM1) Virtually all recovery errors that could occur in connection with paper pickup are handled. |
| Remedy: | 1. Open and close the release lever to reload the paper. 2. Remove the paper once and then refeed it. |
| Error code: | 2E30 |
| Display: | The paper is too small. |
| Description: | Paper mismatch (size) With [Pause] selected for [Paper Mismatch Detection] in the menu setting, paper size for the paper loaded was smaller than the size specified by data. |
| Causes: | The paper width loaded on the printer is shorter than the paper width in print job. |
| Remedy: | Continued printing allowed. Check driver setting Replace with appropriate paper. |
| Error code: | 2E31 |
| Display: | Insufficient paper for job |
| Description: | All of the following conditions have been met at the start of external printing: -[ON] has been selected for [Remaining Roll Paper Detection]. -Among the paper size settings coded in the print data, the paper length exceeds the remaining length of roll paper. -Automatic roll feed to another roll paper slot which is not the current feeding path, out of the 2 slots the printer has, is not available. |
| Remedy: | Replace the roll paper. |
| Error code: | 2E32 |
| Display: | Insufficient paper for job |
| Description: | All of the following conditions have been met at the start of external printing: -[ON] has been selected for [Remaining Roll Paper Detection]. -Among the paper size settings coded in the print data, the paper length exceeds the remaining length of roll paper. -Automatic roll feed to another roll paper slot which is not the current feeding path, out of the 2 slots the printer has, is not available. |
| Remedy: | Replace the roll paper. |
| Error code: | 2E33 |
| Display: | Roll Paper (Paper type) (Paper size) Load Roll Paper Stop Printing. Roll 1(Upper) (Paper type) (Paper size) Press Load/Eject and load a roll. |
| Description: | Paper mismatch (roll paper) No roll paper has been fed when a job with a roll paper specification is received. Paper mismatch (roll paper) No roll paper has been fed when a job with a roll paper specification is received. When paper has not been loaded on either upper or lower slot, and the feeding slot is set to [Automatic] in the job setting, an error of upper roll occurs. |
| Causes: | When receiving the roll paper specified print job, the roll paper has not been fed. The upper roll nor lower roll has not been fed. In addition, the paper feeding slot is “Auto” in job setting. |
| Remedy: | Load roll paper. 1. Select "load a roll" and follow instruction on the panel. 2. Select "stop printing," or stop printing by pressing stop button. 3. Release the release lever and load the paper. |
| Error code: | 2E34 |
| Display: | Roll 2 (Lower) (Paper type) (Paper size) Press Load/Eject and load a roll. Roll 2 (Lower) is selected. Press Load/Eject and load a roll. |
| Description: | Paper mismatch (roll paper) No roll paper has been fed when a job with a roll paper specification is received. When no paper has been loaded on either upper or lower slot, and the feeding slot is set to [Automatic] in the job setting, an error of upper roll (2E33) occurs. Paper mismatch (roll paper) No roll paper has been fed when a job with a roll paper specification is received. When no paper has been loaded on either upper or lower slot, and the feeding slot is set to [Automatic] in the job setting, an error of upper roll (2E33) occurs. * This is a message that appears when paper type/ size specification does not exist due to HPGL format etc. |
| Remedy: | Load roll paper. |
| Error code: | 2E35 |
| Display: | Roll printing is selected. |
| Description: | Paper mismatch (roll paper) No roll paper has been fed when performing internal printing. |
| Remedy: | Load roll paper. |
| Error code: | 2E36 |
| Display: | Roll printing is selected. Press Load/Eject and load a roll. |
| Description: | Paper mismatch (roll paper) (lower) No roll paper was fed when internal printing with the specified roll paper (lower) was started. |
| Remedy: | Load roll paper. |
| Error code: | 2E37 |
| Display: | Roll printing is selected. Roll 1 (Upper) is selected. Press Load/Eject and load a roll. |
| Description: | Paper mismatch (roll paper) (Upper) No roll paper has been fed when a job with roll paper specification is received. Paper mismatch (roll paper) No roll paper was fed when the job specified with upper roll paper was received. |
| Remedy: | Load roll paper. 1. Select "load a roll" and follow instruction on the panel. 2. Select "stop printing," or stop printing by pressing stop button. 3. Release the release lever and load the paper. (This step 3 is only for 800/ 8000/9000 series.) |
| Error code: | 2E38 |
| Display: | Roll 2 (Lower) is selected. Press Load/Eject and load a roll. |
| Description: | Paper mismatch (roll paper)(Lower) No roll paper has been fed when a job with lower roll paper specification is received. |
| Causes: | In printing the printer internal data, the smaller paper than the size specified by each printing data is loaded. |
| Remedy: | Load roll paper. |
| Error code: | 2E39 |
| Display: | The Roll 2 (Lower) is empty. Lift the release lever and replace the roll. |
| Description: | No roll paper available (trailing edge of roll paper detected) -Detected that cut sheet sized paper has been fed at the roll paper feeding slot. -The trailing edge of paper was detected by the Paper detection sensor/ Media sensor sensor during operation in which roll paper was used. -The spool stopped rotating during paper loading or printing (XX: Upper roll paper/ Lower roll paper) |
| Remedy: | 1. Replace the roll paper -Check paper sensor R (I/O mode). 2. Is the paper fed successfully (under a negative load or any other influence)? |
| Error code: | 2E3A |
| Display: | Roll1 jammed. Manually rewind the roll all the way and press OK. |
| Description: | During upper roll paper feeding operation, the paper was fed with the roll feed sensor detecting the paper, but the paper detection sensor/ media sensor sensor could not detect the paper and the operation timed out. |
| Remedy: | Manually rewind the paper and reload. |
| Error code: | 2E3B |
| Display: | Roll 2 (Lwr) jammed. Manually rewind the roll all the way and press OK. |
| Description: | During lower roll paper feeding operation, the paper was fed with the roll feed sensor detecting the paper, but the paper detection sensor/ media sensor sensor could not detect the paper and the operation timed out. |
| Remedy: | Manually rewind the paper and reload. |
| Error code: | 2E3C |
| Display: | Paper jam. Lift the release lever. |
| Description: | During operations with cut sheet, the state of the paper detection sensor/ media sensor sensor has become invalid. |
| Causes: | PAPER ENTRY SENSOR detects no paper loaded on the printer when the printing starts. |
| Remedy: | Reload the paper. |
| Error code: | 2E3D |
| Display: | Roll 1 (upper) jam Lift the release lever. |
| Description: | During operations with upper roll paper, the paper was fed with the roll paper detection sensor and the roll feeding sensor detecting the paper, but the state of the paper detection sensor/ media sensor sensor became invalid. |
| Remedy: | Reload the paper. |
| Error code: | 2E3E |
| Display: | Roll 2 (lower) jam Lift the release lever. |
| Description: | During operations with lower roll paper, the paper was fed with the roll paper detection sensor and the roll feeding sensor detecting the paper, but the state of the paper detection sensor/ media sensor sensor became invalid. |
| Remedy: | Reload the paper. |
| Error code: | 2E3F |
| Display: | Paper jam. Lift the release lever. |
| Description: | When either upper or lower roll paper is in operation, the states of the roll paper detection sensor, roll feeding sensor, and paper detection sensor/ media sensor sensor became invalid. |
| Causes: | Paper jam other than the above Detail Codes (2E3A to 2E3E). |
| Remedy: | Reload the paper. |
| Error code: | 2E40 |
| Display: | Cannot print as selected. Another roll is in use. [Stop]: Stop printing |
| Description: | Print data having lower roll paper specification has been received while upper roll printout remains. |
| Causes: | After starting printing, “No roll sheets” is detected. |
| Remedy: | Remove the printout of upper roll, and print again. |
| Error code: | 2E41 |
| Display: | Cannot print as selected. Another roll is in use. [Stop]: Stop printing |
| Description: | Print data having upper roll paper specification has been received while lower roll printout remains. |
| Remedy: | Remove the printout of lower roll, and print again. |
| Error code: | 2E42 |
| Display: | MediaType Mismatch |
| Description: | Paper mismatch (type/ restart printing of suspended job) It occurs when all of the following conditions are met: -[Stop] selected for [Paper Mismatch Detection] in menu settings. -[Change Paper] button was pressed for suspended jobs from host. -The paper type that has been set in the job and the type of actually fed paper do not match. |
| Causes: | The size of the paper selected in the held job is different from the actual fed paper. |
| Remedy: | Continued printing allowed. Replace with appropriate paper. |
| Error code: | 2E45 |
| Display: | MediaType Mismatch |
| Description: | Paper mismatch (type/ restart printing of suspended job) It occurs when all of the following conditions are met: -[Stop] selected for [Paper Mismatch Detection] in menu settings. -The paper width that has been set with data and the paper width of actually fed paper do not match. |
| Causes: | The width of the roll paper selected in the held job is different from the width of actual fed roll paper. |
| Remedy: | Continued printing allowed. Check the driver settings. Replace with appropriate paper. |
| Error code: | 2E47 |
| Display: | Cutter Position Error |
| Description: | Cut Failure The cutter is not at home position when restart from jam. Also paper feeding was detected. |
| Remedy: | Check around the cutter unit. |
| Error code: | 2F11 |
| Display: | CR error Call for Service. |
| Description: | An operation order has been issued while the carriage suffered a hardware error. |
| Error code: | 2F12 |
| Display: | LF error Call for Service. |
| Description: | LF error -An operation order has been received while the LF suffered a hardware error. -The target position could not be reached within a predicted operation time +3 seconds during an LF operation. -The sensor could not be detected during an LF operation involving sensor detection. |
| Remedy: | 1. Replace the feed roller encoder sensor. 2. Replace the feed motor. <Supplement> -If the carriage travels heavily near the stop position, a mechanical load error may be suspected. -If any other symptom is observed, a feeding sensor may be at fault. |
| Error code: | 2F13 |
| Display: | Hardware error. 03130031-2F13 Turn off printer, wait, then turn on again. |
| Description: | A/D converter external trigger output stop (Hardware error 1) |
| Error code: | 2F14 |
| Display: | Hardware error. 03130031-2F14 Turn off printer, wait, then turn on again. |
| Description: | ASIC register not writable (Hardware error 2) Could not write to the ASIC register on the main controller PCB. |
| Remedy: | Replace the main controller PCB. |
| Error code: | 2F16 |
| Display: | Hardware error. 03130031-2F16 Turn off printer, wait, then turn on again. |
| Description: | Mist fan error The rotation of the mist fan is not detectable. |
| Remedy: | 1. Check the bundled wires in the mist fan drive circuit. 2. Replace the mist fan unit. 3. Replace the main controller PCB. |
| Error code: | 2F17 |
| Display: | Hardware error. 03130031-2F17 Turn off printer, wait, then turn on again. |
| Description: | Platen fan lock detection error The lock signal has been supplied continuously for 3 seconds or longer, 10 seconds after the platen fan started rotating. |
| Remedy: | 1. Check the bundled wires in the platen suction fan drive circuit. 2. Replace the platen suction fan unit. 3. Replace the main controller PCB. |
| Error code: | 2F1F |
| Display: | Hardware error. 03130031-2F1F Turn off printer, wait, then turn on again. |
| Description: | Purge sensor error (recovery purge motor HP detection error) The recovery system has been driven but no sensor interrupt occurs. The recovery system has been driven to close the cap, but the cap has not been capped successfully. |
| Error code: | 2F20 |
| Display: | Hardware error. 03130031-2F20 Turn off printer, wait, then turn on again. |
| Description: | Cap motor cam positioning error The recovery system has been driven but no sensor interrupt occurs. The recovery system has been driven to close the cap, but the cap has not been capped successfully. |
| Error code: | 2F21 |
| Display: | Rel lever is in wrong position. Turn off printer, wait, then turn on again. |
| Description: | Pinch roller open detected with the pinch roller locked. |
| Remedy: | 1. Restart with the pinch roller closed. 2. Check the sensor in I/O DISPLAY in Service mode (Check the pinch roller pressure release detection SW/ the release lever lock sensor.) |
| Error code: | 2F22 |
| Display: | Hardware error. 03130031-2F22 Turn off printer, wait, then turn on again. |
| Description: | Pump shift timeout The target position could not be reached within a predicted operation time +3 seconds during pump operation or no sensor has been detected during a pump operation involving sensor detection. |
| Remedy: | <Supplement> -If the carriage travels heavily towards the stop position: A mechanical load error may be suspected. -Otherwise: The sensor in the purge unit may be at fault. |
| Error code: | 2F23 |
| Display: | Hardware error. 03130031-2F23 Turn off printer, wait, then turn on again. |
| Description: | Purge motor error A PWM duty of 100% has lasted for 200 msec in a pump operation. |
| Remedy: | <Supplement> -If the motor could not be run at all or has resulted in an error after moving by a slight distance: A. A mechanical load error may be suspected. B. The motor or drive circuit may be at fault. -If the carriage has run more or less out of control and resulted in an error: A. The encoder sensor may be at fault. |
| Error code: | 2F24 |
| Display: | Cannot cut paper. Lift the release lever and reload the paper. |
| Description: | Cutter shift timeout The cutter failed to reach the home position in time during a cutting operation |
| Error code: | 2F25 |
| Display: | Hardware error. 03130031-2F25 Turn off printer, wait, then turn on again. |
| Description: | Carriage motor HP not detectable Detected only for the wide format. For the narrow format, the carriage motor HP can be detected when the carriage hits the wall in a full scan following the detection of the HP. |
| Remedy: | Check the carriage HP sensor in I/O mode. <Supplement> -If the motor could not be run at all: A. A mechanical load error may be suspected. B. The motor or drive circuit may be at fault. -If the carriage has resulted in an error after moving at a constant speed: A. The carriage HP sensor may be at fault. -If the carriage has run more or less out of control and resulted in an error: A. The encoder sensor may be at fault. |
| Error code: | 2F26 |
| Display: | Hardware error. 03130031-2F26 Turn off printer, wait, then turn on again. |
| Description: | Carriage operation disabled -A PWM duty of 100% has lasted for 200 msec in a carriage operation -A collision has been detected in a carriage operation (with the speed predicted from the PWM output value having a deviation of 25 ips or more from the actual speed). |
| Remedy: | <Supplement> -If the motor could not be run at all or has resulted in an error after moving by a slight distance: A. A mechanical load error may be suspected. B. The motor or drive circuit may be at fault. -If the carriage has run more or less out of control and resulted in an error: A. encoder sensor may be at fault. |
| Error code: | 2F27 |
| Display: | Hardware error. 03130031-2F27 Turn off printer, wait, then turn on again. |
| Description: | Carriage shift timeout The target position could not be reached within a predicted operation time +3 seconds during carriage operation. |
| Remedy: | <Supplement> -If the carriage travels heavily towards the stop position, a mechanical load error may be suspected. |
| Error code: | 2F28 |
| Display: | Hardware error. 03130031-2F28 Turn off printer, wait, then turn on again. |
| Description: | Lift shift timeout A lift operation has been executed, but no sensor has been detected or a sensor has remained detected. |
| Remedy: | 1. Switch off the printer, then back on. 2. The carriage cannot travel to the lift drive position. 3. The lift drive cam is not engaged. 4. Faulty lift drive sensor 5. Faulty lift drive motor |
| Error code: | 2F29 |
| Display: | Hardware error. 03030000-2F29 Turn off printer, wait, then turn on again. |
| Description: | LF feeding motor timeout (cut sheet) -The target position could not be reached within a predicted operation time +3 seconds during an LF operation. -The sensor could not be detected during an LF operation involving sensor detection. |
| Remedy: | 1. Replace the feed roller encoder sensor. 2. Replace the feed motor. <Supplement> -If the carriage travels heavily near the stop position, a mechanical load error may be suspected. -If any other symptom is observed, a feeding sensor may be at fault. |
| Error code: | 2F2A |
| Display: | Hardware error. 03130031-2F2A Turn off printer, wait, then turn on again. |
| Description: | Cannot detect the LF home position The LF home position could not be detected on LF homing during initialization. |
| Remedy: | 1. Check the sensor (I/O mode check). 2. Replace the feed roller encoder sensor. 3. Replace the encoder film. 4. Replace the feed motor/belt/ adjust the belt tension. 5. Replace the long flexible cable. <Supplement> -If the motor could not be run at all: A. A mechanical load error may be suspected. B. The motor or drive circuit may be at fault. -If the carriage has resulted in an error after moving at a constant speed: The feed roller HP sensor may be at fault. -If the carriage has run more or less out of control and resulted in an error, the encoder sensor may be at fault. When FU2802 blows out on iPF6300/ 6400 series -Replace the main controller PCB. |
| Error code: | 2F2B |
| Display: | Hardware error. 03130031-2F2B Turn off printer, wait, then turn on again. |
| Description: | LF operation failure (LF operation disabled) A pump duty of 100% has lasted for 200 msec during LF operation. |
| Remedy: | 1. Replace the feed roller encoder sensor. 2. Replace the feed motor. <Supplement> -If the motor could not be run at all or has resulted in an error after moving by a slight distance: A. A mechanical load error may be suspected. B. The motor or drive circuit may be at fault. -If the carriage has run more or less out of control and resulted in an error, the encoder sensor may be at fault. When FU2802 blows out on iPF6300/ 6400 Series -Replace the main controller PCB. |
| Error code: | 2F2C |
| Display: | Hardware error. 03130031-2F2C Turn off printer, wait, then turn on again. |
| Description: | Cassette shift timeout -The target position could not be reached within a predicted operation time + 3 seconds during cassette operation. -No sensor has been detected during a pump operation involving sensor detection. |
| Remedy: | <Supplement> -If the carriage travels heavily near the stop position, a mechanical load error may be suspected. -Otherwise, the cassette unit sensor may be at fault. |
| Error code: | 2F2D |
| Display: | Cassette not working. Turn off printer, wait, then turn on again. |
| Description: | Cassette operation disabled A PWM duty of 100% has lasted for 200 msec in a cassette operation. |
| Remedy: | 1. Check the cassette motor and the drive circuit. 2. Check the cassette encoder sensor. |
| Error code: | 2F2E |
| Display: | Hardware error. 03130031-2F2E Turn off printer, wait, then turn on again. |
| Description: | Roll shift timeout No sensor has been detected during a roll operation involving sensor detection. |
| Error code: | 2F2F |
| Display: | Hardware error. 03800500-2F2F Turn off printer, wait, then turn on again. |
| Description: | Non-ejection detection error As a result of nozzle checking made by the head management sensor unit: 1. All 640 nozzles in a nozzle line are nondischarging. 2. At least 50 nozzles have been found mismatched in a nozzle line of 640 nozzles since the last session of detection. |
| Remedy: | 1. Check whether any foreign matter such as paper slip exists on the head management sensor optical axis. 2. Light interception due to ink accumulation.-> Remove the ink/ Replace the unit. 3. Check the head management sensor`s connector connection 4. If Service mode nozzle check pattern printing is no problem, replace the head management sensor unit. Reference 1) As for the detection condition 1. above, in the iPF650/750, iPF6300/6350, and iPF8300 series or later, the error codes are broken up into 2F40,2F41,2F42,2F43,2F44, and 2F47 depending on the non-ejection conditions. Reference 2) Error 2F2F,2F40,2F41,2F42,2F43,2F44, and 2F47 are detected in the following order. 1. Determines signal level (2F47) of head management sensor 2. Determines complete non-ejection of all colors (2F40) 3. Determines multiple mismatches (2F2F) 4. Determines complete non-ejection of a single color (2F41) 5. Determines complete non-ejection of one line (2F42) 6. Determines complete non-ejection of 640 nozzles (2F43) 7. Determines non-ejection of more than 320 nozzles (2F44) Reference 3) The amount of change (between non-ejecting and ejecting nozzle counts) from the last session of nozzle checking is defined as the amount of mismatch. |
| Error code: | 2F30 |
| Display: | Hardware error. 03800500-2F30 Turn off printer, wait, then turn on again. |
| Description: | Non-ejection detecting position error No detectable region has been found during non-ejection position adjustment. |
| Error code: | 2F32 |
| Display: | Multi-sensor error Turn off printer, wait a while, then turn it on again. |
| Description: | Faulty multisensor Light quantity adjustment of multisensor failed. Or, outside light entered during multisensor light quantity adjustment. |
| Remedy: | 1. Retry the adjustment with the effect of outside light, such as that of the afternoon sun, being removed. 2. Check the position at which the multisensor is installed. 3. Replace the multisensor. |
| Error code: | 2F33 |
| Display: | Use another paper. Press Online to clear the error. |
| Description: | Unadjustable because of transparent paper Paper are unidentifiable on automatic adjustment (transparent/semi-transparent paper). |
| Remedy: | Change to appropriate paper. |
| Error code: | 2F34 |
| Display: | Cannot calibrate. Press OK and try calibration again. |
| Description: | Color calibration error The adjustment value has gone out of bounds during calibration. |
| Remedy: | 1. Check to see if the loaded paper permit calibration. 2. Check calibrated printed matter for soiling and other defects. 3. Check the nozzle pattern |
| Error code: | 2F35 |
| Display: | Calibration There is a problem with the multi-sensor. Press OK to cancel calibration. |
| Description: | Faulty multisensor (on calibration) A failure to calibrate has been detected from the parts counter. |
| Remedy: | 1. Check the parts counter in service mode and replace the multisensor unit. 2. Initialize the counter for the replacement unit mounted. (It is recommended to estimate the usage status of other units coming to the end of their service life and replace them as needed.) |
| Error code: | 2F37 |
| Display: | ERROR E173-2F37 Call for service |
| Description: | Linear scale error No signal is available from the carriage encoder when the printhead is driven. |
| Error code: | 2F38 |
| Display: | Top cover is open. Turn off printer, wait a while, and turn it on again. |
| Description: | The top cover is abnormally open. |
| Remedy: | Check the cover. Check the sensor (I/O mode). |
| Error code: | 2F3A |
| Display: | Hardware error. 03130031-2F3A Turn off printer, wait, then turn on again. |
| Description: | Ink Supply Valve Open/Closed motor timeout error |
| Remedy: | 1. Replace the ink supply unit. 2. Replace the main controller PCB. |
| Error code: | 2F3B |
| Display: | Hardware error. 03130031-2F3B Turn off printer, wait, then turn on again. |
| Description: | CS communication error An irrecoverable communication error has occurred communicating between the CS chip mounted on the ink tank and the main unit. |
| Remedy: | 1. Remove and insert the ink tank, or replace the ink tank. 2. Check bundled wires in the ink tank unit and the main controller PCB. 3. Replace the main controller PCB. |
| Error code: | 2F3C |
| Display: | Hardware error. 03130031-2F3C Turn off printer, wait, then turn on again. |
| Description: | LF nip sensor error. When executing nip automatic operation, one of the following conditions is met. -The sensor detected nip closed after the nip completed opening operation. -The sensor detected nip open after the nip completed closing operation. |
| Remedy: | Check the lift cam sensor/ pressure release switch (I/O mode) |
| Error code: | 2F3D |
| Display: | Hardware error. 03130031-2F3D Turn off printer,wait, then turn on again. |
| Description: | HP pre-ejection pump motor overload error |
| Remedy: | Replace the HP maintenance jet tray unit. |
| Error code: | 2F3E |
| Display: | Hardware error. 03130031-2F3E Turn off printer,wait, then turn on again. |
| Description: | HP pre-ejection pump motor shift timeout |
| Remedy: | Replace the HP maintenance jet tray unit |
| Error code: | 2F3F |
| Display: | Hardware error. 03130031-2F3F Turn off printer,wait, then turn on again. |
| Description: | An error other than overload error or shift timeout error has been detected for the HP pre-ejection pump motor. |
| Remedy: | Replace the HP maintenance jet tray unit. |
| Error code: | 2F40 |
| Display: | Hardware error. 03800500-2F40 Turn off printer,wait, then turn on again. |
| Description: | When the result of non-ejection detection is as follows. When non-ejection has been detected for all nozzles of all colors -The error code assuming a problem in the supply system/ purge system/ main controller PCB (electric). |
| Error code: | 2F41 |
| Display: | Hardware error. 03800500-2F41 Turn off printer,wait, then turn on again. |
| Description: | When the result of non-ejection detection is as follows: Complete non-ejection of nozzles in 1 to 5 chip(s). (A line EVEN/ A line ODD/ B line EVEN/ B line ODD Total of 2560 nozzles x 1 to 5 chip(s) complete non-ejection) -Error code assuming a problem in the ink supply system/ purge system. |
| Error code: | 2F42 |
| Display: | Hardware error. 03800500-2F42 Turn off printer,wait, then turn on again. |
| Description: | When the result of non-ejection detection is as follows: Complete non-ejection of one line in 1chip. (In either A line or B line, a complete nonejection of 1280 nozzles) -Error code assuming broken flexible cable or contact failure (heat enable line). |
| Error code: | 2F43 |
| Display: | Hardware error. 03800500-2F43 Turn off printer,wait, then turn on again. |
| Description: | When the result of non-ejection detection is as follows: Complete non-ejection (640 nozzles) of EVEN line or ODD line. -Error code assuming broken flexible cable or contact failure (data line). |
| Error code: | 2F44 |
| Display: | Hardware error. 03800500-2F44 Turn off printer,wait, then turn on again. |
| Description: | When the result of non-ejection detection is as follows: More than half of 640 nozzles in EVEN line or ODD line have non-ejection (more than 320 nozzles). -Error code assuming a head failure such as broken heater board of head. |
| Error code: | 2F46 |
| Display: | Hardware error. 03130031-2F46 Turn off printer,wait, then turn on again. |
| Description: | The shutter HP sensor did not respond at startup and at switching of platen shutter at printing. |
| Remedy: | Check the platen shutter HP sensor (I/ O Display). Check/ replace the platen shutter drive unit or sensor |
| Error code: | 2F47 |
| Display: | Hardware error. 3800500-2F47 Turn off printer,wait, then turn on again. |
| Description: | The optical axis of the head management sensor unit has been intercepted for some reasons. The amount of LED luminescence and the level of detection signal of diode light receiving sensitivity has gone beyond the predefined range. (determines the level of APCCHK)(It`s not a problem of printhead or ink supply system.) |
| Remedy: | 1. Check whether any foreign matter such as paper slip exists on the head management sensor optical axis. 2. Light interception due to ink accumulation.-> Remove the ink/ Replace the unit. 3. Check connection of the head management sensor`s connector. 4. Main controller PCB (Check the fuse/ Replace the PCB.) 5. A large amount of ink mist has been attached to optical element. 6. Replace the head management sensor. |
| Error code: | 2F48 |
| Display: | Hardware error. 03130031-2F48 Turn off printer, wait, then turn on again. |
| Description: | VHT (heater drive drive power supply for printhead) error VHT has gone below or above the rating. |
| Remedy: | iPF6300 series 1. Replace the printhead. 2. Replace the main controller PCB. iPF8300 series 1. Replace the printhead. 2. Replace the CR relay board. 3. Check/ replace the long flexible cable. 4. Replace the main controller PCB. |
| Error code: | 2F49, 2F50, 2F51 |
| Display: | Hardware error. 03130031-xxxx Turn off printer, wait, then turn on again. |
| Description: | Printhead short-circuited detected. Prior to VH power on, it has been detected that the printhead had been damaged due to paper jam etc, and ink went inside the terminal area causing near short-circuit. 2F49: L side printhead 2F50: R side printhead 2F51: LR both printhead |
| Remedy: | iPF6300 series 1. Replace the printhead 2. Replace the main controller PCB. iPF8300 series 1. Replace the printhead 2. Replace the CR relay board 3. Check/ replace the long flexible cable. 4. Replace the main controller PCB. |
| Error code: | 2F4A |
| Display: | Hardware error. 03130031-2F4A Turn off printer, wait, then turn on again |
| Description: | main controller PCB error. |
| Remedy: | Replace the main controller PCB. |
| Error code: | 2F4D |
| Display: | Hardware error. 03130031-2F4D Turn off printer, wait, then turn on again. |
| Description: | VHT leak detection error of left printhead, in case of VHT exceeds rated value or falls below the rated value. |
| Remedy: | For iPF6400 series, 1. Replace the printhead. 2. Replace the main controller PCB. For iPF8400/9400 series, 1. Replace the printhead. 2. Replace the CR relay board. 3. Check and replace the long flexible cable printed circuit. 4. Replace the main controller PCB. |
| Error code: | 2F4F |
| Display: | Hardware error. 03130031-2F4F Turn off printer, wait, then turn on again. |
| Description: | VHT leak detection error of right and left printhead or a single printhead, in case of VHT exceeds rated value or falls below the rated value. |
| Error code: | 2F52 |
| Display: | Hardware error. 03130031-2F52 Turn off printer, wait, then turn on again. |
| Description: | Detected that a carriage unit of a legacy model has been mounted (iPF8300/6300/ 6350 only). |
| Remedy: | Replace with an appropriate carriage unit. 1. Replace with an appropriate carriage unit. 2. Replace the printhead. 3. Replace the main controller PCB |
| Error code: | 2F53 |
| Display: | Hardware error. 03130031-2F53. Turn off printer,wait, then turn on again. |
| Description: | Supply valve motor error of the left ink tank. Drove supply valve motor. The movement was not detected. |
| Remedy: | iPF8400/9400 Series 1. Replace the left ink tank unit. 2. Replace the main controller PCB. |
| Error code: | 2F54 |
| Display: | Hardware error. 03130031-2F54. Turn off printer,wait, then turn on again. |
| Description: | Supply valve motor error of the right ink tank. Drove supply valve motor. The movement was not detected. |
| Remedy: | iPF8400/9400 Series 1. Replace the right ink tank unit. 2. Replace the main controller PCB. |
| Error code: | 2F60 |
| Display: | Spectrophotometer Unit not connected. Turn off power and attach Spectrophotometer Unit. |
| Description: | Spectrophotometer unit won`t return signals. |
| Remedy: | 1. Install spectrophotometer unit. 2. Replace signal line. 3. Replace connection. 4. Replace spectrophotometer unit PCB. |
| Error code: | 2F61 |
| Display: | Hardware error 038A0002-2F61 Turn off printer, wait a while, then turn it on again. |
| Description: | UART communication error. (Data transfer volume in consistency, checksum error etc.) |
| Remedy: | 1. Replace signal line. 2. Replace connection. 3. Replace spectrophotometer unit PCB |
| Error code: | 2F62 |
| Display: | Hardware error 038A0002-2F62 Turn off printer, wait a while, then turn it on again. |
| Description: | When transmitting specified pulses to spectrophotometer carriage motor, the spectrophotometer carriage unit won`t respond to spectrophotometer carriage HP sensor. |
| Remedy: | 1. Replace spectrophotometer unit PCB. 2. Replace lines around spectrophotometer carriage unit. 3. Replace spectrophotometer carriage motor. |
| Error code: | 2F63 |
| Display: | Hardware error 038A0002-2F63 Turn off printer, wait a while, then turn it on again. |
| Description: | The spectrophotometer up-down unit upper detection sensor won`t respond when a predefined pulse is sent to the spectrophotometer up-down unit motor. |
| Remedy: | 1. Replace spectrophotometer updown unit motor. 2. Replace spectrophotometer updown unit upper detection sensor. 3. Re-install delivery guide. 4. Replace the spectrophotometer unit PCB. |
| Error code: | 2F65 |
| Display: | Hardware error 038A0002-2F65 Turn off printer, wait a while, then turn it on again. |
| Description: | When a predefined pulse is sent to the spectrophotometer up-down unit motor, the spectrophotometer up-down unit lower detection sensor in spectrophotometer unit won`t respond. |
| Remedy: | 1. Replace spectrophotometer updown unit motor. 2. Replace spectrophotometer updown unit lower detection sensor. 3. Re-install delivery guide. 4. Replace the spectrophotometer unit PCB. |
| Error code: | 2F66 |
| Display: | Hardware error 038A0002-2F66 Turn off printer, wait a while, then turn it on again. |
| Description: | Media dry fan won`t return signals. |
| Remedy: | 1. Replace fan 2. Replace signal lines 3. Replace the spectrophotometer unit PCB. |
| Error code: | 2F67 |
| Display: | Hardware error 038A0002-2F67 Turn off printer, wait a while, then turn it on again. |
| Description: | Embedded FlashROM read/ write error |
| Remedy: | Replace the spectrophotometer unit PCB. |
| Error code: | 2F68 |
| Display: | Hardware error 038A0002-2F68 Turn off printer, wait a while, then turn it on again. |
| Description: | Spectrophotometer EEPROM read/write error |
| Remedy: | Replace the spectrophotometer unit PCB. |
| Error code: | 2F69 |
| Display: | Hardware error 038A0002-2F69 Turn off printer, wait a while, then turn it on again. |
| Description: | Write/read error at RAM check |
| Remedy: | Replace the spectrophotometer unit PCB. |
| Error code: | 2F6A |
| Display: | Hardware error 038A0002-2F6A Turn off printer, wait a while, then turn it on again. |
| Description: | Firmware update failed. |
| Causes: | The print head which had been installed into a different model before was installed. |
| Remedy: | 1. Update firmware again 2. Replace the spectrophotometer unit PCB. |
| Error code: | 2F6B |
| Display: | Hardware error 038A0002-2F6B Turn off printer, wait a while, then turn it on again. |
| Description: | Initialization after power on of CPU at spectrophotometer unit side failed. |
| Causes: | The print head which had been installed into the model that used a different ink set before was installed. • This error occurs in service mode only. |
| Remedy: | Replace the spectrophotometer unit PCB. |
| Error code: | 2F6C |
| Display: | Hardware error. 03130031-2F6C. Turn off printer, wait, then turn on again. |
| Description: | Failed self-testing. |
| Remedy: | Replace the spectrophotometer unit PCB. |
| Error code: | 2F70 |
| Display: | Hardware error. 03130031-2F70. Turn off printer, wait, then turn on again. |
| Description: | Indication at ink priming error in both subtanks. |
| Remedy: | For iPF6400 Series, 1. Replace both of the inktank units. 2. Replace the main controller PCB. |
| Error code: | 2F71 |
| Display: | Hardware error. 03130031-2F71. Turn off printer, wait, then turn on again. |
| Description: | Indication at ink priming error in the left subtank. |
| Remedy: | For iPF6400 Series, 1. Replace the left inktank unit. 2. Replace the main controller PCB. |
| Error code: | 2F72 |
| Display: | Hardware error. 03130031-2F72. Turn off printer, wait, then turn on again. |
| Description: | Indication at ink priming error in the right subtank. |
| Remedy: | For iPF6400 Series, 1. Replace the right subtank 2. Replace the main controller PCB. |
| Error code: | 2F80 |
| Display: | Spectrophotometer sensor is not mounted. Please check if the sensor is mounted properly and press OK. |
| Description: | Spectrophotometer sensor won`t return signals. |
| Remedy: | 1. Install Spectrophotometer sensor. 2. Check cables. 3. Replace spectrophotometer sensor. 4. Replace the spectrophotometer unit PCB. |
| Error code: | 2F81 |
| Display: | Spectrophotometer Unit Calibration white tile error. Clean the tile then mount it and press OK. |
| Description: | After white calibration, the spectrophotometer sensor returned a value other than predetermined value. |
| Remedy: | 1. Clean white tile. 2. Mount white tile. 3. Replace spectrophotometer sensor. |
| Error code: | 2F82 |
| Display: | Delivery guide of SP unit is not mounted. Check if the guide is mounted properly and press OK. |
| Description: | While the spectrophotometer up-down unit upper detection sensor and spectrophotometer top cover open/closed detection sensor are detecting, the interlock switch remains OFF. |
| Remedy: | 1. Mount delivery guide. 2. Replace the spectrophotometer unit PCB. 3. Replace spectrophotometer updown unit upper detection sensor. |
| Error code: | 2F83 |
| Display: | Backing plate error in the spectrophotometer unit. Clean the backing plate. Install the backing plate to the unit. Then press [OK]. |
| Description: | No signal retuned from backing plate. The signal from the backing plate is beyond threshold. |
| Remedy: | 1. Clean the backing plate. 2. Replace the spectrophotometer unit PCB. 3. Replace the spectrophotometer sensor. |
| Error code: | 2F85 |
| Display: | SP unit up and down cover is open. Close it and press OK |
| Description: | Spectrophotometer top cover open/closed detection sensor won`t respond. |
| Remedy: | 1. Close spectrophotometer top cover. 2. Replace spectrophotometer top cover open/closed detection sensor. 3. Replace the spectrophotometer unit PCB. |
| Error code: | 2F86 |
| Display: | SP unit cover is open. Close it and then press OK. |
| Description: | Spectrophotometer cover open/closed detection sensorwon`t respond. |
| Remedy: | 1. Close spectrophotometer cover. 2. Replace cover sensor. 3. Replace the spectrophotometer unit PCB. |
| Error code: | 2F87 |
| Display: | Colorimetric readout error. Please press OK and execute color measuring again. |
| Description: | When executing color measuring, the spectrophotometer sensor returned a value other than predetermined value was returned. |
| Remedy: | 1. Operate paper feed adjustment. 2. Change the patch size to large. 3. Printer support (In case of printing failure). 4. Replace spectrophotometer sensor |
| Error code: | 2F88 |
| Display: | Colorimetric readout error. Please press OK and execute color measuring again. |
| Description: | When reading the positioning bar, a value other than predetermined value was returned. |
| Remedy: | 1. Operate paper feed adjustment. 2. Printer support (In case of printing failure). 3. Replace spectrophotometer sensor. |
| Error code: | 2F89 |
| Display: | Colorimetric readout error. Please press OK and execute color measuring again |
| Description: | 1) No shifting amount detected from the positioning bar reading value. 2) Position shifting exceeded the threshold value. 3) Skew exceeded the threshold value. |
| Remedy: | 1. Operate paper feed adjustment. 2. Printer support (In case of printing failure). 3. Replace spectrophotometer sensor |
| Error code: | 2F90 |
| Description: | Detected 3V of abnormal power out from the printhead. (Latch up current flows at head logic and temporarily the print head falls into abnormal state ; it is possible to recover by power on and off.) |
| Error code: | 2FA0 |
| Display: | It is recommended to clean the white calibration board to prevent it from possible dirt |
| Description: | Inform the calibration timing of the spectrophotometer sensor. |
| Remedy: | Calibrate the spectrophotometer sensor. |
| Error code: | 4001 |
| Display: | ERROR E146-4001 Call for service. |
| Description: | Polygon motor synchronization error After polygon motor is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and Engine PWB (YC15) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 401A |
| Display: | ERROR E602-401A Call for service. |
| Description: | HDD failure Failed to read and write to and from the HDD. |
| Remedy: | 1. Restart in service mode. 2. Remove and install HDD 3. Replace HDD. Switch on service mode after the replacement. |
| Error code: | 401B |
| Display: | ERROR E602-401B Call for service. |
| Description: | Poor HDD connection The HDD and the HDD controller are not indefinable. |
| Remedy: | 1. Restart in service mode. 2. Remove and install HDD 3. Replace HDD. Switch on service4. Replace HDD controller or the main controller PCB. Restart after the replacement. |
| Error code: | 401C |
| Display: | ERROR E198-401C Call for service. |
| Description: | Faulty RTC Any error other than the two errors mentioned below has been detected while initializing the RTC at startup. |
| Remedy: | 1. Restart the printer in service mode. 2. Replace the main controller PCB. |
| Error code: | 401D |
| Display: | ERROR E198-401D Call for service. |
| Description: | RTC low battery error A battery error has been detected while initializing the RTC at startup. |
| Remedy: | 1. Restart the printer in service mode. 2. Check the RTC battery. 3. Replace the main controller PCB. |
| Error code: | 401E |
| Display: | ERROR E198-401E Call for service. |
| Description: | RTC clock stop The RTC has been detected idle while initializing the RTC at startup. |
| Remedy: | 1. Restart the printer in service mode. 2. Replace the main controller PCB. |
| Error code: | 4027 |
| Display: | Hardware error. 03130031-4027 Turn off printer, wait, then turn on again. |
| Description: | Lift shift timeout error A lift operation has been executed, but no sensor has been detected or a sensor has remained detected. |
| Remedy: | 1. Switch off the printer, then back on. 2. The carriage cannot travel to the lift drive position. 3. The lift drive cam is not engaged. 4. Faulty lift drive sensor 5. Faulty lift drive motor 6. Replace the main controller PCB. |
| Error code: | 4034 |
| Display: | ERROR E196-4034 Call for service. |
| Description: | Multisensor unit version error A different version of multisensor is installed. This would not occur in an ordinary user environment. |
| Error code: | 4037 |
| Display: | ERROR E173-4037 Call for service. |
| Description: | Linear scale error No signal is available from the carriage encoder when the printhead is driven. |
| Error code: | 403E |
| Display: | ERROR E161-403E Call for service. |
| Description: | Head abnormal temperature rise (printhead 1 (R), or A model) Either of the two Di sensors maintained for each printhead chip (color-specific) has been detected at 120 degrees C or higher or -10 degrees C or lower. |
| Error code: | 403F |
| Display: | ERROR E161-403F Call for service. |
| Description: | Head abnormal temperature rise (printhead 2 (L)) Either of the two Di sensors maintained for each printhead chip (color-specific) has been detected at 120 degrees C or higher or -10 degrees C or lower. |
| Error code: | 4040 |
| Display: | ERROR E196-4040 Call for service. |
| Description: | Checksum error The checksum of a file transmitted on execution of the firmware update is unmatched. |
| Remedy: | 1. Start in download mode to upgrade the firmware. 2. Restart the printer in service mode to clear the error. 3. Replace the main controller PCB. |
| Error code: | 4041 |
| Display: | ERROR E196-4041 Call for service. |
| Description: | Flash erase error Failed to erase flash ROM on execution of the firmware update. |
| Remedy: | 1. Start in download mode to upgrade the firmware. 2. Restart the printer in service mode to clear the error. 3. Replace the main controller PCB. |
| Error code: | 4042 |
| Display: | Unknown file. Check file format. Turn off printer, wait a while, then turn it on again. |
| Description: | MIT data transfer failure Failed to write MIT data on its transmission. |
| Remedy: | 1. Execute "Initialize Paper Type" from the system settings. (Note: All paper information will be reset to its factory defaults and additional Paper deleted.) 2. Upgrade the firmware in download mode. 3. Replace the main controller PCB. |
| Error code: | 4043 |
| Display: | ERROR E196-4043 Call for service. |
| Description: | Firmware update failure error Failed to allocate a work area on RAM on firmware update. |
| Remedy: | 1. Start in download mode to upgrade the firmware. 2. Restart the printer in service mode to clear the error. 3. Replace the main controller PCB. |
| Error code: | 4044 |
| Display: | ERROR E196-4044 Call for service. |
| Description: | EEPROM size error Size information about the firmware data transmitted on firmware update and the size of actually transmitted data do not match. |
| Remedy: | 1. Start in download mode to upgrade the firmware. 2. Restart the printer in service mode to clear the error. 3. Check the firmware transfer environment (IF changes, PC). 4. Replace the main controller PCB. |
| Error code: | 4045 |
| Display: | ERROR E196-4045 Call for service. |
| Description: | Engine EEPROM write error An EEPROM read/write failure has been detected in the engine portion of the firmware. |
| Remedy: | 1. Start in download mode to upgrade the firmware. 2. Restart the printer in service mode to clear the error. 3. Replace the main controller PCB. |
| Error code: | 4046 |
| Display: | ERROR E141-4046 Call for service. |
| Description: | Recovery part revolutions reaching 50,000 cycles or more Recovery part operations have reached a predetermined count. |
| Remedy: | Check the parts counter and replace required parts. (Replacement of the parts coming to the end of their useful lives is recommended.) Initialize the counter for the replacement unit mounted. The iPF5000/500/600 have a counter problem fixed. Identify the firmware version and start in download mode to upgrade the firmware to Ver.1.13 or later from any earlier release. |
| Error code: | 4047 |
| Display: | ERROR E144-4047 Call for service. |
| Description: | Carriage count error Supply part operations have reached a predetermined count. |
| Remedy: | Check the parts counter and replace the target unit or Refresh Service Kit. Initialize the parts counter for the target unit after the replacement. |
| Error code: | 4048 |
| Display: | ERROR E144-4048 Call for service. |
| Description: | Non-discharging nozzles on initial filling An unallowable number of nondischarging nozzles have been detected at the completion of initial filling. |
| Error code: | 4049 |
| Display: | Unknown file. Check file format. Turn off printer, wait a while, then turn it on again. |
| Description: | Wrong transfer ROM data model Files for a different model have been transferred on firmware update. |
| Remedy: | 1. Restart the printer in service mode to clear the error (this error won`t occur when FUT is used). 2. Start in download mode to upgrade the firmware. 3. Replace the main controller PCB. |
| Error code: | 404A |
| Display: | ERROR E194-404A Call for service. |
| Description: | Non-ejection count error A non-ejection part operation counter has reached a specified limit. |
| Remedy: | Check the parts counter and replace the target unit or Refresh Service Kit. Initialize the parts counter for the target unit after the replacement. |
| Error code: | 404B |
| Display: | ERROR E199-404B Call for service. |
| Description: | Temperature/humidity sensor error When temperature 0 and humidity 0% are detected, the detection mechanism is considered failed and an error message is displayed. |
| Remedy: | 1. Restart the printer in service mode to clear the error. 2. Identify the firmware version and update the firmware to the last release if it is earlier than Ver.1.31 (firmware defect). 3. Remove and reinsert the temperature/humidity sensor PCB connector 4. Replace the temperature/humidity sensor PCB. |
| Error code: | 404C |
| Display: | ERROR E196-404C Call for service. |
| Description: | Serial number information mismatch A mismatch has been detected between the serial number information stored in the EEPROM on the main controller PCB and that stored in the EEPROM on the MTC relay PCB at startup. |
| Remedy: | 1. Check to see if the correct PCB is mounted, since a PCB of the wrong model may have been mistakenly mounted during servicing. 2. Invoke service mode to implement PCB replacement. |
| Error code: | 404D |
| Display: | ERROR E196-404D Call for service. |
| Description: | Machine ID information mismatch A mismatch has been detected between the model ID information stored in the EEPROM on the main controller PCB and that stored in the EEPROM on the MTC relay PCB at startup. |
| Remedy: | 1. Check to see if the correct PCB is mounted, since a PCB of the wrong model may have been mistakenly mounted during servicing. 2. Invoke service mode to implement PCB replacement. |
| Error code: | 404E |
| Display: | ERROR E196-404E Call for service. |
| Description: | An EEPROM read/ write error has been detected in the controller portion of the firmware. |
| Remedy: | 1. Start in download mode to upgrade the firmware. 2. Start in service mode to clear the error. 3. Replace the main controller PCB. |
| Error code: | 404F |
| Display: | ERROR E144-404F Call for service. |
| Description: | Pump revolutions full The number of HP pre-ejection pump revolution has reached the defined value. |
| Remedy: | Clear the counter in service mode after having replaced the HP pre-ejection tray unit. |
| Error code: | 4050 |
| Display: | Error E161-4050 Call for service. For iPF6000, 03800500-4050. |
| Description: | Non-ejection detection error The timing of "ink priming sequence" is fallowing. -At installation of a new model printer -At reinstallation after the second transportation. -At replacement of the printhead |
| Error code: | 405A |
| Display: | Error E602-405A Call for service. |
| Description: | Incorrect capacity HDD model is connected. |
| Remedy: | Replace HDD |
| Error code: | 405B |
| Display: | Error E602-405B Call for service. |
| Description: | Mismatched HDD model is connected. |
| Remedy: | Replace HDD |
| Error code: | 4061 |
| Display: | The paper loaded askew. Remove the paper. |
| Description: | Postion ditection of askew loaded paper. |
| Error code: | xx01xxxx-xxxx |
| Description: | Jam-related |
| Error code: | xx03xxxx-xxxx |
| Description: | Cover-related |
| Error code: | xx06xxxx-xxxx |
| Description: | Media-related |
| Error code: | xx13xxxx-xxxx |
| Description: | Controller-related |
| Error code: | xx1Axxxx-xxxx |
| Description: | HDD-related |
| Error code: | xx32xxxx-xxxx |
| Description: | Media-related |
| Error code: | xx34xxxx-xxxx |
| Description: | PDL-related |
| Error code: | xx80xxxx-xxxx |
| Description: | Printhead-related |
| Error code: | xx81xxxx-xxxx |
| Description: | Inktank-related |
| Error code: | xx83xxxx-xxxx |
| Description: | Inktank-related |
| Error code: | xx84xxxx-xxxx |
| Description: | Maintenance cartridge-related |
| Error code: | xx86xxxx-xxxx |
| Description: | Print-related |
| Error code: | xx87xxxx-xxxx |
| Description: | Cutter-related |
| Error code: | xx89xxxx-xxxx |
| Description: | Media take-up unit-related |
| Error code: | xx90xxxx-xxxx |
| Description: | Version up-related |
Парткод
Название
CANON PFI-101C Картридж голубой
CANON PFI-101M Картридж пурпурный
CANON PFI-101Y Картридж желтый
CANON PFI-101PC Картридж фото-голубой
CANON PFI-101PM Картридж фото-пурпурный
CANON PFI-101R Картридж красный
CANON PFI-101G Картридж зеленый
CANON PFI-101B Картридж синий
CANON MC-16 Емкость для отработанных чернил
CANON PFI-103MBK Картридж матово-черный
CANON PFI-103BK Картридж черный
CANON PFI-103GY Картридж серый
CANON PFI-103PGY Картридж фото-серый
CANON PF-03 Печатающая головка
